Cast Steel. Carbon and Stainless Steel Gate, Globe and Check Valves

Cast Steel Carbon and Stainless Steel Gate, Globe and Check Valves

Contents Cast Steel Standard Features 3 Testing, Modifications and Accessories Standard Product Range With DSI Zy-Gear Bevel Gear Chart NACE Conformance And General Design Specifications Specifying DSI Carbon Steel Figure Numbers Specifying DSI Stainless Steel Figure Numbers 7 Gate Valves -13 Globe Valves 1-17 Swing Check Valves 1-21 Pressure Temperature Ratings 22 Warranty And Returns Policy 23

Standard Features of Cast Steel Valves Low Fugitive Emission Service standard Cast Steel Gate, Globe and Check Valves are designed and manufactured to ensure leakage of less than 0 ppm (parts per million) of volatile organic compounds. Extensive base line laboratory testing (static and cycle testing) has been performed establishing critical design parameters necessary to achieve low emission sealing in the stem packing Critical Design and Manufacturing Controls Applied To Produce Low Emission Service Valves In Standard Products. Stem Straightness and Roundness Stem Surface Finish To Max. 32 Ra Stuffing Box Surface Finish To Max. 12 Ra Stuffing Box and Gland Cylindricity Self Centering Gland Design Gland Packing: Die-formed Graphite Rings with Braided Graphite Top and Bottom Rings. Bonnet Gaskets: Class 10 Gate: SS Tanged Clad Graphite Class 10 Globe & Check: SS Spiral Wound Grafoil Class 300 Valves: SS Spiral Wound Class 00 & igher: Ring Type Joint seal area for Gate and Globe Valves and in the bonnet gasket sealing area (cover gasket for Check Valves). In-house testing procedure has been developed and is periodically performed to ensure that standard product design and manufacturing criteria consistently result in the Gate, Globe and Check Valve meeting a maximum of 0 ppm VOC leakage prior to shipment. Low Emission Design Options Live Load Packing In services requiring frequent cycling or with high pressure/ temperature variations, live loading extends the service life between maintenance periods by requiring less frequent packing gland adjustments. Belleville springs are employed to provide constant packing gland stress. Lantern Ring and Double Packing Set Lantern ring with leak-off fitting connection and double packing stack is optionally available for critical services. Packing System Cast Steel Gate and Globe valves use a combination of dieformed flexible graphite and interbraided graphite in a predetermined arrangement to ensure an effective seal. Graphite packing achieves its maximum ability to isolate the atmosphere when it is contained within a chamber that is precise in finish and dimension. Gate and Globe valves are manufactured with stem finishes better than 32 Ra and stuffing box wall finishes for 12 Ra. In addition, stem straightness and taper are closely controlled. Standard Packing Live Load Packing Bevel Packing Lantern Ring Packing 3

Testing, Modifications and Accessories for Cast Steel valves Zy-Tech Global Industries offers In-ouse NDE Testing, a variety of Product Modifications and Accessories, saving our customers time and resources by eliminating the need for multiple purchase orders, time and transportation costs. A single warranty then applies to each modified product, with each product inspected for quality and conformance to our customer's specifications and industry standards. Available Modifications for DSI Cast Steel Valves Packing and Gasket Changes End Connection Modifications Gear Operator Mounting Trim Changes Actuation Cryogenic Gas Columns and Wheel Extensions Teflon Disc Inserts Drilled & Tapped Body/Bonnet Connections By-Pass Pressure Equalizing Acid Shields Oxygen & Chlorine Cleaning & Packaging Weld End Bore Changes Customer Specified Coatings Outside Lever and Weight for Check Valves Slam Retarders for Check Valves Chain Wheel Operator Block and Bleed NDE Testing Available (In-ouse) Dye Penetrant Test Magnetic Particle Test Radiography PMI (Positive Material Identification) API Performance Testing Cast Steel Valves Standard Product Range with Zy-Gear Bevel Gear Chart offers a broad range of standard commodity Cast Steel Valves in flanged and weld end connections. The chart for Zy- Gears is based on torque ratings for each valve at maximum differential pressure. Valve Type Pressure Class Size Range Bonnet Disc Zy-Gear 2"-12" - 7B 10 2"-" Bolted OS&Y Flex 1"-2" - 207B 30" & 3" - 307B 2"-" - 7B 300 2"-30" Bolted OS&Y Flex 12"- 20" - 207B 2" & 30" - 307B 2"- " - 7B Gate 00 2"-2" Bolted OS&Y Flex "-12" - 207B 1"-2" - 307B 2"-" - 7B 900 2"-2" Bolted OS&Y Flex "-" - 207B 12"-1" - 307B 2"-" - 7B 100 2"-12" Bolted OS&Y Flex "-" - 207B "-12" - 307B 10 2"-1" Bolted OS&Y Plug 2"-1" - 207B Globe 300 2"-12" Bolted OS&Y Plug 2"-"* - 207B 00 2"-" Bolted OS&Y Plug 2"-" - 207B 10 2"-2" Bolted Swing n/a Swing Check 300 2"-2" Bolted Swing n/a 00 2"-1" Bolted Swing n/a Industry inter-changeable pre-drilled mounting pattern per MSS SP1. Note: DSI Cast Steel Globe and Check Valves are available in Classes 900 and 100. Contact your salesperson for more information. *" & 12" standard from factory.

Conformance NACE MR017 Compliant Over recent years the demand for valves resistant to sulfide stress cracking in facilities handling 2S bearing hydrocarbons has increased dramatically. Varying concentrations of 2S, pressure, temperature and the medium itself, whether it be fluid, gas or multi-phase, plus other factors all have a bearing on the appropriate metallic material selection. offers three basic valves which have been proven reliable and which fully comply with the NACE MR017 Latest Edition specification. The typical material configurations of the NACE compliant Carbon and Low Temperature Carbon Steel Gate Valves are shown below. NACE Compliant Material Specifications for Gate Valves LUF-N LUF-N-LCC XUF-N Valve Parts Carbon Steel LowTempCarbon Steel Carbon Steel Notes Body, Bonnet ASTM A21 WCB ASTM A32 LCC ASTM A21 WCB Maximum hardness 22Rc/23B "& under ASTM A12 F " & under ASTM A/ eat affected zone and weld deposit hardnesses Disc + Disc Faces " & above ASTM A21 ASTM A32 LCC/ Stellite, " & above WCB/ ASTM A21 WCB/Stellite are controlled to 22 Rc/23B maximum ASTM A27 T, All from solid bar or forging, no welding, Stem, Backseat ASTM A12 F ASTM A12 F ASTM A12 FA maximum hardness 22Rc/23B Gland ASTM A12 FA ASTM A12 F ASTM A12 FA Same as above Seat + Seat Faces ASTM A plus Stellite weld deposit ASTM A32 LF2 plus Stellite weld deposit Base material and heat affected zone hardnesses ASTM A/Stellite are controlled to 22Rc/23B maximum, Stellite facing to NACE MR017 Sec. and Sec. Bonnet Bolts ASTM A193 B7M ASTM A320 L7M ASTM A193 B7M Materials are suitable for direct exposure to 2S, NACE MR017 Sec. Bonnet Nuts ASTM A19 2M ASTM A19 7M ASTM A19 2M Same as above Note: Other trims available in NACE. Welding Material Test Reports Welding and weld repair operations are conducted in accordance with applicable ASTM material specifications and NACE MR017 using procedures and personnel qualified to ASME Section IX. General Design Specifications Cast Steel Valves are manufactured in strict accordance with the following standards: Material test reports for Cast Steel valves are available upon request. Material test reports meet the requirements of EN 20 3.1b American Standard British Standard Item Description BS (Gate Valve) API 00 BS173 (Globe Valve) Shell wall thickness and general valve design specifications BS1 (Check Valve) ANSI B1.3 BS10 Pressure temperature ratings ANSI B1. BS200 Face-to-face dimensions, End-to-end dimensions ANSI B1.* BS10 End flange dimensions, Gasket contact facing BS (Gate Valve) ANSI B1.2 BS173 (Globe Valve) Welding end dimensions BS1 (Check Valve) *Valves 2 and larger according to ANSI B1.7 Series A (MSS SP-) and Series B (API 0).

Specifying Cast Carbon Steel Valve Figure Numbers It s easy to specify Cast Steel Valves. Just follow the example and use the figure number chart below to specify the valve you need. Carbon Steel Example: " Class 00 Gate Valve with RTJ Flanged Ends operated by a Zy-Gear Bevel Gear Operator, API Trim No. 12 with Flex Wedge, Special NACE Design meeting NACE MR017 Requirements, and utilizing ASTM A32 LCC for Special Body Material, Graphoil Packing and Gaskets. " G R LUF* N LCC A B C D E F G Size Operation End Pressure Trim Special Special Body Packing and Connection Classes Material Design Material Gasket Material G No Denotation for See Chart Below See Chart Below N No Symbol Required No Denotation for Gear Operated Raised Face For API Trim No. Nace MR017 for ASTM A21 WCB Graphoil Packing R *F designates LCC and Gaskets RTJ Flanged Ends Flex Wedge ASTM A32 LCC T FF for Gates C PTFE Packing Flat Faced Ends ASTM A217 C and Gaskets C12 ASTM A217 C12 WC ASTM A217 WC Valve Type Class Flanged End Welding End 10 37 37 1 /2 300 23 23 1 /2 Gate 00 1 /2 900 73 73 1 /2 100 77 77 1 /2 10 133 133 1 /2 300 1 /2 Globe 00 11 11 1 /2 900 173 173 1 /2 100 179 179 1 /2 10 137 137 1 /2 300 19 19 1 /2 Swing Check 00 1 1 1 /2 900 177 177 1 /2 100 19 19 1 /2 Symbol API Trim No. Seating* Disc/Seat Stem/Backseat U F/F 13Cr XU 13Cr/F 13Cr AU Monel/F Monel LU 12 /F L / LUU 1** F/F A 9 Monel/Monel Monel *Note: F denotes hardfaced with Stellite. **Per API 00 th Edition. Note: All information is subject to change without notice.

Specifying API 00 Cast Stainless Steel Valve Figure Numbers It s easy to specify API 00 Cast Steel Valves. Just follow the example and use the figure number chart below to specify the valve you need. Stainless Steel Example: 1" Class 00 Gate Valve with RTJ Flanged Ends, operated by a Zy-Gear Bevel Gear Operator, Stainless Steel and half Stellite Trim, API 00 Design, utilizing CFM Stainless Steel Body Material, and Graphoil Packing and Gaskets. DSI G R 1 1 FS A B C D E F G I DSI Series Operation Pressure End Body Trim Stellite Packing and Design Classes Connection Material Material Option Gasket Material DSI No Denotation See Chart Below No Denotation 0 0 FS No Denotation for manual for Raised Face A31 CF 30 SS alf Stellite for Graphoil API 00 Design Operation Flanged End 0L 0L Trim Packing and G R A31 CF3 30 LSS U Gaskets Gear Operated RTJ Flanged Ends 1 1 Full Stellite T FF A31 CFM SS Trim PTFE Packing Flat Faced Ends 1L 1L and Gaskets A31 CF3M L SS 17 17 A31 CGM 7 SS 17L 17L A31 CG3M 7L SS 7 7 A31 CFC 37 SS A20 A20 A31 CN7M Alloy 20 21 321 SS Valve Type Class Flanged End Welding End 10 37 37 1 /2 300 23 23 1 /2 Gate 00 1 /2 900 73 73 1 /2 100 77 77 1 /2 10 133 133 1 /2 300 1 /2 Globe 00 11 11 1 /2 900 173 173 1 /2 100 179 179 1 /2 10 137 137 1 /2 300 19 19 1 /2 Swing Check 00 1 1 1 /2 900 177 177 1 /2 100 19 19 1 /2 Note: All information is subject to change without notice. 7

Gate Valves Class 00, 900 &100 Class 300 Class 10 Parts And Materials Class 10, 300, 00, 900 &100 Item Part Name WCB LCC C C12 WC CFM 1 Body A21 WCB A32 LCC A217 C A217 C12 A217 WC A31 CFM 2 Bonnet A21 WCB A32 LCC A217 C A217 C12 A217 WC A31 CFM Flex Wedge (" & under) A/STL A12 F A12 F9/STL A12 F9/STL A12 FA A31 CFM Flex Wedge (" & above) A21 WCB/STL A32 LCC/F A217 C/STL A217 C12/STL A217 WC/13Cr A31 CFM Seat Rings* A/STL A30 LF 2/STL A33-P/STL AISI 321/STL A33-P/STL A20 Stem A27 T A12 F A27 T A27 T A27 T A79 7 Backseat A12 FA A12 F A12 FA A12 FA A12 FA A31 CFM Studs A193 B7 A320 L7M A193 B7 A193 B7 A193 B7 A193 B 9 Stud Nuts A19 2 A19 7M A19 2 A19 2 A19 2 A19 Gasket Cl. 10 Graphite GE Graphite Sheet Gasket Cl. 300 Spiral Wound Metal Graphite Spiral Wound Gasket Cl. 00 & above Ring Joint Spiral Wound andwheel A7, A3 A7, A3 A7, A3 A7, A3 A7, A3 A197 12 Gland Flange AISI 1 AISI 1 AISI 1 AISI 1 AISI 1 A31 CF 13 Yoke Sleeve A39 TYPE D2 A39 TYPE D2 A39 TYPE D2 A39 TYPE D2 A39 TYPE D2 A39 Type D2 1 andwheel Nut A7 A7 A7 A7 A7 30 SS 1 Retainer Nut AISI 1 AISI 1 AISI 1 AISI 1 AISI 1 CS 20+Cr 1 Gland A12 FA A12 F A12 FA A12 FA A12 FA 17 Spacer A12 FA A12 F A12 FA A12 FA A12 FA 1 Eyebolts A193 B7 A193 B7 A193 B7 A193 B7 A193 B7 A193 B 19 Eyebolt Pins AISI 1 AISI 1 AISI 1 AISI 1 AISI 1 A79 30 20 Eyebolt Nuts A19 2 A19 2 A19 2 A19 2 A19 2 A19 21 Packing Graphite Stack (Braided and Die-Formed Graphite Rings) Pillar +2 23 Grease Fitting Commercial Commercial Commercial Commercial Commercial Commercial 2 Nameplate AISI 30 AISI 30 AISI 30 AISI 30 AISI 30 NPS 1" and Over (12" and Over on Stainless) 2 Yoke Bearings Commercial Commercial Commercial Commercial Commercial 2 Studs A193 B7 A193 B7 A193 B7 A193 B7 A193 B7 A193 B 27 Stud Nuts A19 2 A19 2 A19 2 A19 2 A19 2 A19 Yoke A21 WCB A32 LCC A21 WCB A21 WCB A21 WCB A31 CF NPS 3" 2 Studs A193 B7 A193 B7 A193 B7 A193 B7 A193 B7 29 Stud Nuts A19 2 A19 2 A19 2 A19 2 A19 2 30 Cover A21 WCB A32 LCC A21 WCB A21 WCB A21 WCB *Welded Seat Rings. Contact your DSI salesperson for more information.

Class 10 Gate Valves (37-37 1 /2) Dk 1 1 OPEN 1 20 1 21 23 13 12 1 19 17 7 2 NPS 1"-30" Ball Bearing Yoke Sleeve 2 30 29 2 1 9 NPS 3" Ball Bearing Yoke Sleeve 2 D D3 D2 D1 2 27 17 a L n x d f L1 NPS 1" And Over 2 Piece Yoke Dimensional Data (in.) and Flow Coefficient (Cv) End Flange Bolt ole Size D D1 D2 n d D3 a f L L1 1(open) Dk Wt. Lbs. Cv 2 2.00.00.7 0.7 3.2 0.3 0.0 7.00.0 12.0 1.3 7.7 29.7 2 1 /2 2.0 7.00.0 0.7.13 0.71 0.0 7.0 9.0 1.9 19. 9. 7.7 3 3.00 7.0.00 0.7.00 0.7 0.0.00.12 1.93 20. 9. 9.1.00 9.00 7.0 0.7.1 0.9 0.0 9.00 12.00 19.09 23.70 9. 3 123.00.00 9.0 0.7.0 1.02 0.0.0 1. 2.91 32.0.1 13 273.9.00 13.0.7 0.7.3 1.1 0.0.0 1.0 30.9 39.9 1.7 273 9.1.00 1.00 1.2 12 0.9 12.7 1.22 0.0 13.00 1.00 37..2 17.72 32 22. 12 12.00 19.00 17.00 12 0.9 1.00 1.2 0.0 1.00 19.7 3.70.70 19.9 121. 1 13.2 21.00 1.7 12 1.12 1.2 1.3 0.0 1.00 22.0 7.0 2.09 19.9 0 171.7 1 1.2 23.0 21.2 1 1.12 1.0 1. 0.0 1.00 2.00.1 71.1 22.0 123 230.3 1 17.2 2.00 22.7 1 1.2 21.00 1.7 0.0 17.00 2.00 1.00 79.0 2.0 1 3003. 20 19.2 27.0 2.00 20 1.2 23.00 1.9 0.0 1.00 2.00.0.3 2.0 172 3772.2 2 23.2 32.00 29.0 20 1.3 27.2 1.9 0.0 20.00 32.00 7.2 2. 27.9 27 739. 30(A) 29.00 3.7 3.00 2 1.3 33.7 2.9 0.0 2.00 3.00 93.70 12.01.0 7 90 30(B) 29.00 3.9 33. 0.7 32.00 1.77 0.0 2.00 3.00 93.70 12.01.0 19 90 3(A) 3.0.00 2.7 32 1.1 0.2 3. 0.0 2.00 0.00 7. 1.93 3.3 70 13.1 3(B) 3.0 1.2 39.7 0.9 3.2 2.09 0.0 2.00 0.00 7. 1.93 3.3 272 13.1 9

Class 300 Gate Valves (23-23 1 /2) Dk 1 1 OPEN 1 20 23 13 12 NPS 12"-2" Ball Bearing Yoke Sleeve 2 1 1 (approx.) 21 2 17 19 7 2 9 NPS 30" And Over Ball Bearing Yoke Sleeve 30 29 2 1 2 D D3 D2 D1 27 17 n x d NPS 12" And Over 2 Piece Yoke a L f L1 Dimensional Data (in.) and Flow Coefficient (Cv) End Flange Bolt ole Size D D1 D2 n d D3 a f L L1 1(open) Dk Wt. Lbs. Cv 2 2.00.0.71 0.7 3.2 0.91 0.0.0.0 1.17 17.00 7.7 0 29. 2 1 /2 2.0 7.0.7 0.7.13 1.02 0.0 9.0 9.0 17.13 20. 9. 2 2. 3 3.00.2.1 0.7.00 1.1 0.0.12.12 1. 21.93 9. 9 72.1.00.00 7.7 0.7.1 1.2 0.0 12.00 12.00 20.7 2.0 9. 13 9..00 12.0.3 12 0.7.0 1. 0.0 1. 1. 27.7 3. 1.7 29 277..00 1.00 13.00 12 1.00.3 1. 0.0 1.0 1.0 3.92.13 17.72 00 93..00 17.0 1.2 1 1.12 12.7 1.9 0.0 1.00 1.00 1.2 2.2 19.9 77 792.9 12 12.00 20.0 17.7 1 1.2 1.00 2.00 0.0 19.7 19.7.09 7.09 19.9 1213 929. 1 13.2 23.00 20.2 20 1.2 1.2 2.13 0.0 30.00 30.00 9.00 3.29 22.0 170 1. 1 1.2 2.0 22.0 20 1.3 1.0 2.2 0.0 33.00 33.00.79 72.33 2.0 22 21207. 1 17.00 2.00 2.7 2 1.3 21.00 2.0 0.0 3.00 3.00 1.00 79.0 2.0 200 21.1 20 19.00 30.0 27.00 2 1.3 23.00 2.2 0.0 39.00 39.00 7..1 27.9 32 390.3 2 23.00 3.00 32.00 2 1.1 27.2 2.7 0.0.00.00 79.92.3.0 2 17. 30(A) 29.00 3.00 39.2 2 1.9 33.7 3.2 0.0.00.00 2.3 13.2 3.3 93 0 30(B) 29.00 39.00 3.2 3 1.0 33.2 3.70 0.0.00.00 2.3 13.2 3.3 900 0 3(A) 3.0 0.00.00 32 1.73 0.2.13 0.0.00.00 7.0 1. 37.2 13029 3(B) 3.0. 2. 32 1.73 39.7.09 0.0.00.00 7.0 1. 37.2 123

Class 00 Gate Valves (- 1 /2) Dk 1 1 23 1 OPEN 20 13 12 NPS " And Over Ball Bearing Yoke Sleeve 2 1 1 19 21 17 7 2 2 27 2 17 1 9 NPS " And Over 2 Piece Yoke D D3 D2 D1 n x d a L f L1 Dimensional Data (in.) and Flow Coefficient (Cv) End Flange Bolt ole Size D D1 D2 n d D3 a f L L1 1(open) Dk Wt. Lbs. Cv 2 2.00.0.00 0.7 3.2 1.02 0.2.0.0 1.17 17.00 7.7 90 20.7 2 1 /2 2.0 7.0.91 0.7.13 1.1 0.2 13.00 13.00 17.2 20.7 9. 9 07. 3 3.00.2.3 0.7.00 1.2 0.2 1.00 1.00 17.99 21.1 9. 133..00.7.0 0.9.1 1. 0.2 17.00 17.00 21.1 2.22.1 20..00 1.00.0 12 1..0 1.9 0.2 22.00 22.00.30 3. 19.9 719 20. 7.7 1.0 13.7 12 1.2.3 2.20 0.2 2.00 2.00 3.0 2.92 19.9 2 3. 9.7 20.00 17.00 1 1.3 12.7 2.2 0.2.00.00 1.73 2. 2.0 1709 72. 12.73 22.00 19.2 20 1.3 1.00 2. 0.2 33.00 33.00.1 9.0 2.0 2271 73 1 12.7 23.7 20.7 20 1.0 1.2 2.7 0.2 3.00 3.00.12 9. 27.9 22 1 1 1.7 27.00 23.7 20 1.1 1.0 3.03 0.2 39.00 39.00 0.3 77.9 27.9 203.3 1 1.0 29.2 2.7 20 1.73 21.00 3.2 0.2 3.00 3.00 9.29.9.0 3 21.1 20 1.2 32.00 2.0 2 1.73 23.00 3.0 0.2 7.00 7.00 73.2 9.7.0 390.3 2 22.00 37.00 33.00 2 2.00 27.2.02 0.2.00.00.3 1.3 3.3 907 17.

Class 900 Gate Valves (73-73 1 /2) Dk 1 1 23 1 OPEN 20 13 12 NPS " And Over Class 900 Ball Bearing Yoke Sleeve 2 1 1 19 21 17 7 2 2 27 2 17 1 9 NPS " And Over 2 Piece Yoke D D3 D2 D1 n x d a L f L1 Dimensional Data (in.) and Flow Coefficient (Cv) End Flange Bolt ole Size D D1 D2 n d D3 a f L L1 1(open) Dk Wt. Lbs. Cv 3 2.7 9.0 7.0 0.9.00 1. 0.2 1.00 1.00 20.3 2.3.1 23 0. 3..0 9.2 1.2.1 1.77 0.2 1.00 1.00 23.90 2. 1.7 379 1.9.7 1.00 12.0 12 1.2.0 2.20 0.2 2.00 2.00.9 3.9 19.9 2 23. 7.0 1.0 1.0 12 1.0.3 2.2 0.2 29.00 29.00 3.39 7. 2.0 1 27. 9.37 21.0 1.0 1 1.0 12.7 2.7 0.2 33.00 33.00 3. 3. 27.9 1973 2. 12.1 2.00 21.00 20 1.0 1.00 3.12 0.2 3.00 3.00 9.37 2.37 27.9 277 13 12

Class 100 Gate Valves (77-77 1 /2) Dk 1 1 23 1 OPEN 20 13 12 NPS 3" And Over Class 100 Ball Bearing Yoke Sleeve 2 1 1 19 21 17 7 2 2 27 2 17 1 9 NPS " And Over 2 Piece Yoke D D3 D2 D1 n x d a L f L1 Dimensional Data (in.) and Flow Coefficient (Cv) End Flange Bolt ole Size D D1 D2 n d D3 a f L L1 1(open) Dk Wt. Lbs. Cv 2 1.97.0.0 0.9 3.2 1. 0.2 1.0 1.0 1.7 21.1 9. 1 29.1 3 2.7.0.00 1.2.00 1.9 0.2 1.0 1.0 23.3 27.0 1.7 332 37.7 3.2 12.2 9.0 1.3.1 2.13 0.2 21.0 21.0 2.0 29.1 17.72 9 97..39 1.0 12.0 12 1.0.0 3.27 0.2 27.7 27.7 32. 39. 22.0 3 222.2 7.00 19.00 1.0 12 1.73.3 3.2 0.2 32.7 32.7 3.9 7. 27.9 220 07..7 23.00 19.00 12 2.00 12.7.2 0.2 39.00 39.00.7 7.3.0 339 1.1 12.39 2.0 22.0 1 2.13 1.00. 0.2.0.0 1.1 3.7.0 72 917. 13

Globe Valves Class 10 Class 300 Class 00, 900 &100 Parts And Materials Class 10, 300, 00, 900 & 100 Item Part Name WCB LCC C C12 WC CFM 1 Body A21 WCB A32 LCC A217 C A217 C12 A217 WC A31 CFM 2 Bonnet A21 WCB A32 LCC A217 C A217 C12 A217 WC A31 CFM Disc A217 CA1 A31 CFM A217 C/STL A217 C12/STL A217 WC/STL A31 CFM Disc "-12" A21 WCB/13Cr A32 LCC/F A217 C/STL A217 C12/STL A217 WC/STL A31 CFM Seat Ring A/STL A32 LF2/F A33-P/STL AISI 321/STL A33-P/STL A31 CFM Stem A27 T A12 F A27 T A27 T A27 T A79 7 Backseat A12 FA A12 F A12 FA A12 FA A12 FA A31 CFM Studs A193 B7 A320 L7M A193 B7 A193 B7 A193 B7 A193 B 9 Stud Nuts A19 2 A19 7M A19 2 A19 2 A19 2 A19 Gasket Cl. 10 Spiral Wound Graphite Graphite Sheet Gasket Cl. 300 Spiral Wound Graphite Spiral Wound Gasket Cl. 00 & above RTJ Spiral Wound Stem Lock Nut A12 FA A12 F A12 FA A12 FA A12 FA A79 12 Nameplate AISI 30 AISI 30 AISI 30 AISI 30 AISI 30 andwheel A7, A3 A7, A3 A7, A3 A7, A3 A7, A3 A197 32 Gland Flange AISI 1 AISI 1 AISI 1 AISI 1 AISI 1 A31 CF 33 Yoke Sleeve A39 Type D2 A39 Type D2 A39 Type D2 A39 Type D2 A39 Type D2 A39 Type D2 3 andwheel Nut A7, A19 2 A7, A19 2 A7, A19 2 A7,A19 2 A7,A19 2 A19 3 Bonnet A21 WCB A21 WCB A21 WCB A21 WCB A21 WCB 3 Gland A12 FA A12 F A12 FA A12 FA A12 FA A79 37 Spacer A12 FA A12 F A12 FA A12 FA A12 FA 3 Eyebolts A193 B7 A193 B7 A193 B7 A193 B7 A193 B7 A193 B 39 Eyebolt Pins AISI 1 AISI 1 AISI 1 AISI 1 AISI 1 A79 30 0 Eyebolt Nuts A19 2 A19 2 A19 2 A19 2 A19 2 A19 1 Packing Braided and Die-Formed Graphite Rings 3 Bearing Commercial Commercial Commercial Commercial Commercial Grease Fitting Commercial Commercial Commercial Commercial Commercial Studs A193 B7 A193 B7 A193 B7 A193 B7 A193 B7 Stud Nuts A19 2 A19 2 A19 2 A19 2 A19 2 7 Guide AISI 1 AISI 1 AISI 1 AISI 1 AISI 1 Studs Commercial Commercial Commercial Commercial Commercial 0 Pins AISI 1 AISI 1 AISI 1 AISI 1 AISI 1 1 ub A7 A7 A7 A7 A7 2 Washer AISI 1 AISI 1 AISI 1 AISI 1 AISI 1 30 Gear Cl. 300 " & 12" Commercial Commercial Commercial Commercial Commercial Commercial Contact your DSI salesperson for more information. 1

Class 10 Globe Valves (133-133 1 /2) Dk 3 2 3 33 33 1 1 OPEN 0 3 7 32 3 NPS "-12" Guide Detail NPS 2"-" Standard andwheel 9 39 37 1 2 3 3 12 7 Secured By Spot Weld Weld On Circumference D D3 D2 D1 NPS "-12" ammer-blow andwheel Rising, Non-Rotating Stem 1 a L n x d f L1 0 NPS "-12" Disc to Stem Engagement Detail Dimensional Data (in.) and Flow Coefficient (Cv) End Flange Bolt ole Size D D1 D2 n d D3 a f L L1 1(open) Dk Wt. Lbs. Cv 2 2.00.00.7 0.7 3.2 0.3 0.0.00.00 13. 1.9 7.7.9 2 1 /2 2.0 7.00.0.7.13 0.71 0.0.0.0 19.30 21.07 9. 77 72.2 3 3.00 7.0.00 0.7.00 0.7 0.0 9.0 9.0 1.7 17.2 9. 93..00 9.00 7.0 0.7.1 0.9 0.0.0.0 1. 20.2 1.7 13 1.00.00 9.0 0.7.0 1.00 0.0 1.00 1.00 20.0 22.0 17.72 2 00.00 13.0.7 0.7.3 1.12 0.0 19.0 19.0 21.97 2.2 17.72 37.00 1.00 1.2 12 0.9 12.7 1.19 0.0 2.0 2.0 29.0 32. 19.9 17. 12 12.00 19.00 17.00 12 0.9 1.00 1.2 0.0 27.0 27.0 32. 3.7 19.9 33 1900. 1

Class 300 Globe Valves (- 1 /2) Dk 3 1 OPEN 3 33 7 0 9 12 3 3 39 Secured By Spot Weld 32 3 3 1 37 7 2 1 33 30 Axis Of Stem 1 3 NPS "-12" ammer-blow andwheel With Gear Rising, Non-Rotating Stem A Dk Secured By Weld 33 Secured By Weld NPS 2"-3" Standard andwheel Rising, Rotating Stem NPS "-" ammer-blow andwheel Rising, Non-Rotating Stem 2 33 3 2 1 0 Weld On Circumference D D3 D2 D1 a L n x d f L1 NPS " Guide Detail NPS 2"-" Disc to Stem Engagement Detail Dimensional Data (in.) and Flow Coefficient (Cv) End Flange Bolt ole Size D D1 D2 n d D3 a f L L1 1(open) Dk A Wt. Lbs. Cv 2 2.00.0.00 0.7 3.2 0.91 0.0.0.0 1.1 1.73 7.7. 2 1 /2 2.0 7.0.7 0.7.13 1.02 0.0.0.0 17.2 19. 9.. 3 3.00.2.3 0.7.00 1.1 0.0 12.0 12.0 17.91 19. 9. 12.7.00.00 7.7 0.7.1 1.2 0.0 1.00 1.00 20.7 22. 1.7 1 1.00 12.2.3 12 0.7.0 1. 0.0 17.0 17.0 22.3 2.19 17.72 37 3.7.00 1.00 13.00 12 0.9.3 1. 0.0 22.00 22.00. 33.3 19.9 17 92.9.00 17.0 1.2 1 1.12 12.7 1. 0.0 2.0 2.0 32. 3.0 19.9. 91 20. 12 12.00 20.0 17.7 1 1.2 1.00 2.01 0.0 2.00 2.00 3.3 3. 27.9. 127 12. 1

Class 00 Globe Valves (11-11 1 /2) Dk 3 3 33 1 3 OPEN 7 0 9 3 39 32 3 3 1 37 7 2 NPS " Guide Detail Secured By Weld 33 Secured By Weld NPS 2" Standard andwheel Rising, Rotating Stem 2 33 3 2 1 12 Secured By Spot Weld 1 NPS 3"-" ammer-blow andwheel Rising, Rotating Stem 0 Weld On Circumference D D3 D2 D1 a L n x d f L1 NPS 2"-" Disc to Stem Engagement Detail Dimensional Data (in.) and Flow Coefficient (Cv) End Flange Bolt ole Size D D1 D2 n d D3 a f L L1 1(open) Dk Wt. Lbs. Cv 2 2.00.0.00 0.7 3.2 1.30 0.2.0.0 1.93 1.0 1.7 9.2 2 1 /2 2.0 7.0.7 0.7.13 1.1 0.2 13.00 13.00 20.27 22.2 17.72 13 73.2 3 3.00.2.3 0.7.00 1. 0.2 1.00 1.00 20.2 22.2 17.72 13 3.9.00.7.0 0.9.1 1.1 0.2 17.00 17.00 23.23 2.9 17.72 309 19.7.00 1.00.0 12 1..0 2.17 0.2 22.00 22.00 3. 37.21 27.9 79 39. 7. 1.0 13.7 12 1.2.2 2.19 0.2 2.00 2.00 2.39. 22.0 00 79. 17

Swing Check Valves Class 10 Class 300 Class 00, 900 &100 Parts And Materials Class 10, 300, 00, 900 & 100 Item Part Name WCB LCC C C12 WC CFM 1 Body A21 WCB A32 LCC A217 C A217 C12 A217 WC A31 CFM 2 Cover A21 WCB A32 LCC A217 C A217 C12 A217 WC A31 CFM 3 Disc 2"-" A27 T A12 F A12 F9/Stellite A27 T A27 T A31 CFM Disc "-2" A21 WCB/13Cr A32 LCC/F A217 C/Stellite A217C12/13Cr A217 WC/13Cr A31 CFM Arm A21 WCB A32 LCC A217 C A217 C12 A217 WC A31 CFM Seat Ring A/Stellite A30LF2/Stellite A33-P/Stellite AISI 321/Stellite A33-P/Stellite A31 CFM Arm Pin A12 Fa A12 F A12 Fa A12 Fa A12 Fa A79 Disc Nut A12 F A12 F A12 Fa A12 Fa A12 Fa A193 BM Gasket Cl. 10 Spiral Wound Graphite Graphite Sheet Gasket Cl. 300 Spiral Wound Graphite Spiral Wound Gasket Cl. 00 & above RTJ Spiral Wound Studs A193 B7 A320 L7M A193 B7 A193 B7 A193 B7 A193 B 12 Stud Nuts A19 2 A19 7M A19 2 A19 2 A19 2 A19 13 Side Plug CSN 1701 A12 Fa A12 Fa A12 Fa A12 Fa A79 1 Split Pin AISI 30 AISI 30 AISI 30 AISI 30 AISI 30 A0 1 Side Plug Gasket A12 F A12 F A12 F A12 F A12 F A79 17 Nameplate AISI 30 AISI 30 AISI 30 AISI 30 AISI 30 SS 1 Disc Sleeve AISI 20 AISI 20 AISI 20 AISI 20 AISI 20 19 Arm Sleeve AISI 20 AISI 20 AISI 20 AISI 20 AISI 20 20 Eyebolt ASTM A ASTM A ASTM A ASTM A ASTM A Contact your DSI salesperson for more information. 1

Class 10 Swing Check Valves (137-137 1 /2) 12 2 20 " & Over 13 1 19 1 inge Pin Detail 3 D D3 D2 D1 1 1 n x d a f L L1 Dimensional Data (in.) and Flow Coefficient (Cv) End Flange Bolt ole Size D D1 D2 n d D3 a f L L1 Wt. Lbs. Cv 2 2.00.00.7 0.7 3.2 0.3 0.0.00.00.30 32 21.1 3 3.00 7.0.00 0.7.00 0.7 0.0 9.0 9.0.27 99.2.00 9.00 7.0 0.7.1 0.9 0.0.0.0. 97 903.2.00.00 9.0 0.7.0 1.02 0.0 1.00 1.00.3 1 2032.1.00 13.0.7 0.7.3 1.1 0.0 19.0 19.0 12.2 2 379.00 1.00 1.2 12 0.9 12.7 1.22 0.0 2.0 2.0 13. 1 7.9 12 12.00 19.00 17.00 12 0.9 1.00 1.2 0.0 27.0 27.0 1.3 93 3. 1 13.2 21.00 1.7 12 1. 1.2 1.3 0.0.00.00 1.9 77 70. 1 1.2 23.0 21.2 1 1. 1.0 1. 0.0 3.00 3.00 17.91 3 1293.2 1 17.2 2.00 22.7 1 1.2 21.00 1.7 0.0 3.0 3.0 19.9 12 197. 20 19.2 27.0 2.00 20 1.2 23.00 1.9 0.0 3.0 3.0 20.9 13 2912.9 2 23.2 32.00 29.0 20 1.3 27.2 1.9 0.0 1.00 1.00 2.9 231 30. 19

Class 300 Swing Check Valves (19-19 1 /2) 12 2 20 " & Over 13 1 19 1 inge Pin Detail 3 D D3 D2 D1 1 1 n x d a f L L1 Dimensional Data (in.) and Flow Coefficient (Cv) End Flange Bolt ole Size D D1 D2 n d D3 a f L L1 Wt. Lbs. Cv 2 2.00.0.00 0.7 3.2 0. 0.0.0.0.29 2 2.2 2 1 /2 2.0 7.0. 0..12 1.00 0.0.0.0 7.0 330 3 3.00.2.2 0..00 1.12 0.0 12.0 12.0.2 3 2..00.00 7. 0..19 1.2 0.0 1.00 1.00. 129..00 12.0.2 12 0..0 1. 0.0 17.0 17.0.1 217 193.2.00 1.00 13.00 12 1.00.2 1.2 0.0 21.00 21.00 13.07 00 39..00 17.0 1.2 1 1.12 12.7 1. 0.0 2.0 2.0 1.0 9. 12 12.00 20.0 17.7 1 1.2 1.00 2.00 0.0 2.00 2.00 17.79 1 12. 1 13.2 23.00 20.2 20 1.2 1.2 2.12 0.0 33.00 33.00 17.0 23 13. 1 1.2 2.0 22.0 20 1.3 1.0 2.2 0.0 3.00 3.00 21.2 170 171.9 1 17.00 2.00 2.7 2 1.3 21.00 2.3 0.0 3.0 3.0 23.23 1771 12. 20 19.00 30.0 27.00 2 1.3 23.00 2.0 0.0 0.00 0.00 2.19 271 23. 2 23.00 3.00 32.00 2 1.2 27.2 2.7 0.0 3.00 3.00 3.29 1 3371. 20

Class 00 Swing Check Valves (1-1 1 /2) 12 2 20 " & Over 13 1 19 1 inge Pin Detail 3 D D3 D2 D1 1 1 n x d a f L L1 Dimensional Data (in.) and Flow Coefficient (Cv) End Flange Bolt ole Size D D1 D2 n d D3 a f L L1 Wt. Lbs. Cv 2 2.00.0.00 0.7 3.2 1.30 0.2.0.0 7. 2 20.9 3 3.00.2.3 0.7.00 1. 0.2 1.00 1.00 9..00.7.0 0.9.1 1.1 0.2 17.00 17.00.3 20..00 1.00.0 12 1..0 2.17 0.2 22.00 22.00 12.20 29 1900.9 7.7 1.0 13.7 12 1.2.3 2. 0.2 2.00 2.00 1.7 73 333. 9.7 20.00 17.00 1 1.3 12.7 2.0 0.2.00.00 1.77 129 3.7 12.7 22.00 19.2 20 1.3 1.00 2.91 0.2 33.00 33.00 19. 19 72.9 1 12.7 23.7 20.7 20 1.0 1.2 3.03 0.2 3.00 3.00 22.0 2013. 1 1.7 27.00 23.7 20 1.1 1.0 3. 0.2 39.00 39.00 2.9 220 99.3 Contact your DSI salesperson for Class 900 and 100 Dimensional Data. 21

Cast Steel Valves Pressure Temperature Ratings Pressure temperature ratings are based on ANSI/ASME B1.3 (199 edition). The temperatures shown are that of the pressure-containing shell, which is considered to be the same temperature as that of the fluid flowing within it. Special consideration should be given to such items as trim, bonnet gasket material, and packing to assure that the rating is merited in all respects. Maximum Allowable Non-Shock Pressure (PSIG) Service Temperature Class 10 Class 300 Class 00 Class Class Class 900 100 200 F C WCB LCC WC C C12 CFM WCB LCC WC C C12 CFM WCB LCC WC C C12 WCB WCB WCB (a) (b) (c,d) (d) (d) (f) (a) (b) (c,d) (d) (d) (f) (a) (b) (c,d) (d) (d) (a) (a) (a) -20 to 0-29 to 3 2 290 290 290 290 27 70 70 70 70 70 720 10 100 100 100 100 2220 370 170 200 93 20 20 20 20 20 23 7 70 70 7 70 20 130 100 100 190 100 202 337 2 300 19 230 230 230 230 230 21 730 720 71 730 0 1 1 1 130 1 1970 320 70 00 20 200 200 200 200 200 19 3 70 9 70 70 1 1270 1 13 1 1 1900 70 20 00 20 170 170 170 170 170 170 00 0 1200 1330 1330 1330 1330 179 299 990 00 0 0 0 0 0 0 9 12 12 12 12 10 273 0 0 33 12 12 12 12 12 12 3 90 90 90 90 7 7 7 7 7 1 2 7 700 371 1 1 1 1 1 1 3 70 70 70 70 30 3 3 3 3 100 2 0 70 399 9 9 9 9 9 9 0 0 30 30 30 2 1 220 200 00 27 0 0 0 0 0 0 20 2 2 1 1 1 123 200 330 0 270 270 20 3 3 97 9 97 0 130 2230 900 2 0 0 0 0 0 0 170 170 0 370 0 1 3 3 900 70 900 1 0 130 90 3 3 3 3 3 3 320 27 370 3 20 20 0 0 7 0 1 0 00 3 20 20 20 20 20 20 0 0 21 200 290 30 30 00 0 1 20 30 0 20(e) 20(e) 20(e) 20(e) 1 1 190 3 290 290 3 10 93 20(e) 20(e) 20(e) 20(e) 9 0 30 190 200 22 0 21 20(e) 20(e) 20(e) 20(e) 0 0 7 23 12 12 10 1200 9 1(e) 1(e) 20(e) 20(e) 0 3 0 1 7 70 ydrostatic Shell Test Press. 0 2 222 220 330 7 Valve Closure Liquid 320 1 2 130 10 20 00 Test Pressure Air 0 0 0 0 0 Notes: (a) Permissible, but not recommended for prolonged exposure above about 00 F. Upon prolonged exposure to temperatures above about 00 F, the carbide phase of Carbon Steel may be converted to Graphite. (b) Not to be used over 0 F. (c) Not to be used over 10 F. (d) Use normalized and tempered material only. (e) For welding end valves only. Flanged end ratings terminate at 00 F. (f) At temperatures over 00 F, use only when the Carbon content is 0.0% or higher. 22