Jeep Wrangler Rear Vision Camera, 2007 Current (Kit # 9002-8837) Items Included in the Kit Required Tools & Supplies Camera Chassis Harness Zip lock bag with 15 Wire Ties & 3 Push Nuts Program Module 22--pin white connector w/ video T15 & T20 Torx Bits 7mm & 10mm Sockets Phillips Screwdriver Plastic Trim Removal Tool Soldering Iron, Solder, & Heat Shrink Tubing (RECOMMENDED) or T-taps as an alternate splicing method Electrical Tape These instructions Please read so you do not VOID the warranty: If the camera harness is ran though the center on the camera bracket, it will cut the camera harness. This will VOID the warranty on the camera. Safety Precautions: Work in a well-ventilated area that is clear of obstructions. Secure vehicle with tire chucks in both front and rear of tires. Turn vehicle accessories OFF and ensure ignition key is in OFF position. Wear safety goggles and snug fitting clothes. Use tools only for their intended purpose and which are in good repair. Only perform this task if confidence, skill, and physical ability permit. NOTE: We strive to provide accurate and up-to-date installation instructions.
Install Camera: Wheel Alignment for Camera Clearance Step 1: Loosen lug nuts to remove spare tire. Step 2: Slide Camera on studs placing harness end on top of tire carrier. Do not run harness through the camera bracket opening. Step 3: Temporarily replace spare tire to check wheel clearance to Camera. Step 4: Remove spare tire and slide (3) supplied Push Nuts on the studs.
Install Chassis Harness: Step 5: Plug the Camera connector into the gray Chassis Harness connector, and insert RCA connector end of supplied Chassis Harness through the rear gate vent behind tire carrier. Step 8: Use supplied Wire Ties to secure Chassis Harness to existing harness. Step 9: Use supplied Wire Ties to secure Chassis Harness to fabric factory wire cover. CAUTION: Leave enough slack to allow gate to open fully. Step 6: Using a plastic trim removal tool, remove interior panels on inside of rear gate. Step 10: Use a T20 Torx bit to remove subwoofer box. Step 11: Using a plastic trim removal tool, pry off rear seat belt closeout. Step 7: Pull harness through the rear gate openings.
Step 12: Using a plastic trim removal tool, remove rear access panel to expose 10mm bolt, and remove bolt. Step 16: Use a 10mm socket to remove the existing nut located behind the passenger kick panel and attach ground eyelet of Chassis Harness to chassis ground. Step 13: Pull out subwoofer box slightly to gain access to run Chassis Harness along existing harness. Step 14: Pull back carpet and continue running Chassis Harness forward. Step 18: Remove rubber bin insert from top of dash. Step 15: Run Chassis Harness under B-pillar cover to passenger door sill. Use a plastic trim removal tool to remove the (2) plastic push pins and remove passenger sill plate/kick panel. Step 19: Remove 7mm bolt.
Step 20: Using a plastic trim removal tool, remove window switch panel. Step 21: Disconnect harness from window switches. Step 23: Remove driver knee bolster cover. Step 24: Remove (2) 7mm bolts on both sides of the steering column. Step 25: Remove center stack/cluster surround. Step 26: Remove glove box for access and run Chassis Harness toward center of dash. Step 22: Remove 7mm bolt.
Step 27: Using a plastic trim removal tool, remove HVAC panel. Step 31: Plug in the 22 pin white connector to the open connector on the back of the radio. Step 28: Run Red 12v+ ignition power wire and green trigger wire of supplied Chassis Harness to ignition controlled power point on HVAC panel power point. Step 32: Connect White 22-pin Connector to radio along with all remaining radio connectors before reinstalling radio head unit and all trim removed. Step 29: Splice Red power wire and the green trigger wire from the chassis harness to Blue/Red wire on back of power point. RECOMMENDED: Use solder and cover with heat shrink tubing or use T-taps as an alternate connection method. Step 33: Connect male RCA of camera into female RCA of jumper harness and proceed to the Programming Instructions. Step 30: Plug the Chassis Harness RCA connector into your aftermarket display.
Programing Instructions PLEASE NOTE: These modules are VIN locked for single use. a) With the module not plugged in, key on the ignition and wait 10 seconds for the chimes and lights to stop flashing. b) Plug module into OBDII port, located under the dash on the driver s side, and wait to hear honk honk. Programming is completed. c) Unplug the module from the OBDII port. Step 35: Test the system. Start vehicle and shift into Reverse in order to check that all connections were made properly. If all of the connections are correct you will see the camera image displayed on your aftermarket display. Step 36: Reassemble vehicle. Follow your disassembly steps in reverse order, taking care not to bind the harness wiring when reinstalling trim.
Factory Display Camera Harness for Chrysler Town & Country, Dodge Durango, Grand Caravan, & Ram Tradesman, Jeep Commander, Grand Cherokee and Wrangler Factory Displays (Kit part number 9002-2632) NOTE: Requires Chrysler/Dodge dealer to activate; see below Applications: 2011 current Chrysler Town & Country (RBZ, RHB, RER, REZ, RBZ, REW radios) 2011 current Dodge Durango (RHR, RHB, RHZ, RHP radios) 2011 current Dodge Grand Caravan (RBZ, RHB, RER, REZ, RBZ, REW radios) 2011 current Dodge Ram Tradesman (RBZ, RHB, RER, REZ, RBZ, REW radios) 2008 2010 Jeep Commander (430, 730 radios) 2008 current Jeep Grand Cherokee (430, 730, RHR, RHB, RB2, RHP radios) 2007 current Jeep Wrangler (display radios) Please read thoroughly before starting installation and check that kit contents are complete. Items Included in the Kit: Factory Display RCA Jumper Harness Loose red and black wires (if needed) White 22-pin Connector These Instructions Tools & Supplies Needed: Delphi Terminal Removal Tool #12094429 or Small Flat Watch Repair Screwdriver 10mm Socket Plastic Trim Removal Tool Vehicle Service Manual (If needed) Safety Precautions: Work in well ventilated area that is clear of obstructions. Secure vehicle with tire chucks in both front and rear of tires. Turn vehicle accessories OFF and ensure ignition key is in OFF position. Wear safety goggles and snug fitting clothes. Use tools only for their intended purpose and which are in good repair. Only perform this task if confidence, skill, and physical ability permit. NOTE: We strive to provide accurate and up-to-date installation instructions. IMPORTANT: Use of this camera with the factory display requires activation by a Chrysler/Dodge dealer. See below for Dealer Programming Instructions. If possible, have the dealer enable the camera option prior to installation.
Step 1: Use a Plastic Trim Removal Tool to remove console and dash trim pieces to gain access to the radio bezel. Step 2: Use a Plastic Trim Removal Tool to remove radio bezel. Step 3: Unplug all radio connectors from the radio head unit and set radio aside. Only complete Step 4 and 5 for 2014+ Dodge Durango, Jeep Grand Cherokee, RAM Truck vehicles with 52-pin radio connectors. Step 4: Insert terminal from red wire on supplied jumper harness into position 31 of black 52-pin radio connector and insert terminal from black wire on supplied chassis harness into position 32 of black 52-pin radio connector. Continue with steps 6 through 9 for vehicles with 22-pin radio connector. IMPORTANT: If the White 22-pin connector is present in the vehicle and Pin 3 and/or Pin 4 are already populated, remove the terminal(s) using Delphi Terminal Removal Tool #12094429 or a Small Flat Watch Repair Screwdriver and isolate with Electrical Tape. Step 6: Remove both terminals from chassis harness. Splice provided loose red wire to chassis harness red wire and insert terminal into pin position 3 on the white 22-pin radio connector (Figure 1) until it clicks securely. Figure 1 Step 5: Connect male RCA of camera into female RCA of jumper harness and proceed to the Dealer Programming Instructions (Included). Step 7: Splice provided loose black wire to chassis harness black wire and insert terminal into pin position 4 on the white 22-pin radio connector (Figure 1) until it clicks securely. Step 8: Connect White 22-pin Connector to radio along with all remaining radio connectors before reinstalling radio head unit and all trim removed. Step 9: Connect male RCA of camera into female RCA of jumper harness and proceed to the Dealer Programming Instructions (Included).
Dealer Programming Instructions PARK VIEW REAR BACK-UP CAMERA VEHICLE CONFIGURATION Vehicle VIN must be updated with the sales code of the added accessory in order to enable system functionality. Using the DealerCONNECT and the scan tool, complete the procedure below: A. In the Vehicle Option screen under Global Claims System category in the Service tab, enter the VIN and add the following sales code: XAC (PARK VIEW REAR BACK-UP CAMERA) as a Dealer Installed Option. B. Confirm that the new sales code has been successfully added to the VIN. With the scan tool connected to both the internet (via Ethernet port or wireless connection) and the vehicle, perform the following steps: C. Using the scan tool, select VEHICLE PREPARATION and then select RESTORE VEHICLE CONFIGURATION. D. Follow the step by step instructions on the scan tool to complete the Park View Rear Back-Up Camera vehicle configuration. Step 23: Start vehicle and shift into Reverse in order to check that all connections were made properly. If all of the connections are correct you will see the camera image displayed on your factory display. If you re looking for quality cameras & driver safety products by Brandmotion, we ve you covered.