Power distribution & protection

B Product page Miniature circuit breakers (MCB) - Hager B-1 5 - Hager B-5 6 Earth leakage protection - Socomec B-21 - Lovato B-43 Modular isolators - Fanox B-44 - Hager B-7 Modular relays / contactors - Hager B-8 Modular time switches - Hager B-9 - Hager B-10 Surge protection devices (SPD) - CPT B-45 46 - Dehn B-48 Moulded case circuit breakers (MCCB) - Hager B-11-15 Air circuit breakers (ACB) - Hager B-16 18 Load break switches (Isolators) - Socomec B-22 24 - Lovato B-41 42 Changeover switches - Socomec B-25 31 Fuse switches - Socomec B-32 Fuses and bases - DF B-34 40 Power supplies - Delta B-49 50 - Lovato B-51 Transformers - DF B-52

Miniature circuit breakers (MCBs) 6/10kA For the protection and control of circuits against overload and short circuits. Suitable for commercial and industrial installations. Breaking capacity: Field fittable accessories (see page B-5) SANS / IEC 60947-2 10kA auxiliary/alarm contacts IEC 60898 6KA shunt trip device undervoltage release Voltage rating: 240/400V 50-60Hz earth leakage designation current breaking width in rating capacity 17.5mm NF116A NF / HLF series 10kA C curve (5-10 In) Single pole NF100A 0.5A 10kA miniature circuit breaker 1 135.00 1 PP NF101A 1A 10kA miniature circuit breaker 1 128.00 NF102A 2A 10kA miniature circuit breaker 1 128.00 NF103A 3A 10kA miniature circuit breaker 1 128.00 NF106A 6A 10kA miniature circuit breaker 1 79.00 NF110A 10A 10kA miniature circuit breaker 1 79.00 NF116A 16A 10kA miniature circuit breaker 1 79.00 NF120A 20A 10kA miniature circuit breaker 1 79.00 NF125A 25A 10kA miniature circuit breaker 1 81.00 NF132A 32A 10kA miniature circuit breaker 1 81.00 NF140A 40A 10kA miniature circuit breaker 1 88.00 NF150A 50A 10kA miniature circuit breaker 1 108.00 NF163A 63A 10kA miniature circuit breaker 1 112.00 HLF180S 80A 10kA miniature circuit breaker 1.5 454.00 HLF190S 100A 10kA miniature circuit breaker 1.5 458.00 HLF199S 125A 10kA miniature circuit breaker 1.5 660.00 Two pole NF202A 2A 10kA miniature circuit breaker 2 384.00 2 PP NF203A 3A 10kA miniature circuit breaker 2 384.00 NF206A 6A 10kA miniature circuit breaker 2 279.00 NF210A 10A 10kA miniature circuit breaker 2 279.00 NF216A 16A 10kA miniature circuit breaker 2 279.00 NF220A 20A 10kA miniature circuit breaker 2 279.00 NF225A 25A 10kA miniature circuit breaker 2 315.00 NF232A 32A 10kA miniature circuit breaker 2 315.00 NF240A 40A 10kA miniature circuit breaker 2 315.00 NF250A 50A 10kA miniature circuit breaker 2 378.00 NF263A 63A 10kA miniature circuit breaker 2 378.00 NF232A HLF280S 80A 10kA miniature circuit breaker 3 847.00 HLF290S 100A 10kA miniature circuit breaker 3 870.00 HLF299S 125A 10kA miniature circuit breaker 3 1219.00 Triple pole NF302A 2A 10kA miniature circuit breaker 3 612.00 3 PP NF303A 3A 10kA miniature circuit breaker 3 612.00 NF306A 6A 10kA miniature circuit breaker 3 463.00 NF310A 10A 10kA miniature circuit breaker 3 463.00 NF316A 16A 10kA miniature circuit breaker 3 463.00 NF320A 20A 10kA miniature circuit breaker 3 463.00 NF325A 25A 10kA miniature circuit breaker 3 468.00 NF332A 32A 10kA miniature circuit breaker 3 468.00 NF340A 40A 10kA miniature circuit breaker 3 468.00 NF350A 50A 10kA miniature circuit breaker 3 475.00 NF363A 63A 10kA miniature circuit breaker 3 488.00 HLF380S 80A 10kA miniature circuit breaker 4.5 1133.00 HLF390S 100A 10kA miniature circuit breaker 4.5 1219.00 HLF399S 125A 10kA miniature circuit breaker 4.5 1828.00 Four pole NF406A 6A 10kA miniature circuit breaker 4 686.00 4 PP NF410A 10A 10kA miniature circuit breaker 4 686.00 NF416A 16A 10kA miniature circuit breaker 4 686.00 NF420A 20A 10kA miniature circuit breaker 4 686.00 NF425A 25A 10kA miniature circuit breaker 4 709.00 NF432A 32A 10kA miniature circuit breaker 4 709.00 NF440A 40A 10kA miniature circuit breaker 4 709.00 NF450A 50A 10kA miniature circuit breaker 4 754.00 NF463A 63A 10kA miniature circuit breaker 4 754.00 NF320A HLF480S 80A 10kA miniature circuit breaker 6 2742.00 HLF490S 100A 10kA miniature circuit breaker 6 2742.00 HLF499S 125A 10kA miniature circuit breaker 6 3655.00 B-1

Miniature circuit breakers (MCBs) 10/15kA D curve NDN116A For the protection and control of circuits against overload and short circuits. Suitable for commercial and industrial installations. Breaking capacity: Field fittable accessories (see page B-5) SANS / IEC 60947-2 NDN: 10kA - auxiliary/alarm contacts HMD: 15kA - shunt trip device - undervoltage release Voltage rating: 240/400V 50-60Hz - earth leakage designation NDN / HMD series 10/15kA current breaking width in rating capacity 17.5mm D curve (10-20 In) Single pole NDN106A 6A 10kA miniature circuit breaker 1 119.00 1 PP NDN110A 10A 10kA miniature circuit breaker 1 119.00 NDN116A 16A 10kA miniature circuit breaker 1 119.00 NDN120A 20A 10kA miniature circuit breaker 1 119.00 NDN125A 25A 10kA miniature circuit breaker 1 138.00 NDN132A 32A 10kA miniature circuit breaker 1 138.00 NDN140A 40A 10kA miniature circuit breaker 1 138.00 NDN150A 50A 10kA miniature circuit breaker 1 145.00 NDN163A 63A 10kA miniature circuit breaker 1 145.00 HMD180 80A 15kA miniature circuit breaker 1.5 610.00 HMD190 100A 15kA miniature circuit breaker 1.5 711.00 HMD199 125A 15kA miniature circuit breaker 1.5 1169.00 HMD180 Two pole NDN206A 6A 10kA miniature circuit breaker 2 320.00 2 PP NDN210A 10A 10kA miniature circuit breaker 2 320.00 NDN216A 16A 10kA miniature circuit breaker 2 320.00 NDN220A 20A 10kA miniature circuit breaker 2 320.00 NDN225A 25A 10kA miniature circuit breaker 2 356.00 NDN232A 32A 10kA miniature circuit breaker 2 356.00 NDN240A 40A 10kA miniature circuit breaker 2 356.00 NDN250A 50A 10kA miniature circuit breaker 2 381.00 NDN263A 63A 10kA miniature circuit breaker 2 381.00 HMD280 80A 15kA miniature circuit breaker 3 1340.00 HMD290 100A 15kA miniature circuit breaker 3 1436.00 HMD299 125A 15kA miniature circuit breaker 3 2234.00 NDN363A Triple pole NDN306A 6A 10kA miniature circuit breaker 3 585.00 3 PP NDN310A 10A 10kA miniature circuit breaker 3 585.00 NDN316A 16A 10kA miniature circuit breaker 3 585.00 NDN320A 20A 10kA miniature circuit breaker 3 585.00 NDN325A 25A 10kA miniature circuit breaker 3 625.00 NDN332A 32A 10kA miniature circuit breaker 3 625.00 NDN340A 40A 10kA miniature circuit breaker 3 625.00 NDN350A 50A 10kA miniature circuit breaker 3 681.00 NDN363A 63A 10kA miniature circuit breaker 3 681.00 HMD380 80A 15kA miniature circuit breaker 4.5 1929.00 HMD390 100A 15kA miniature circuit breaker 4.5 2234.00 HMD399 125A 15kA miniature circuit breaker 4.5 2792.00 HMD399 Four pole NDN406A 6A 10kA miniature circuit breaker 4 1067.00 4 PP NDN410A 10A 10kA miniature circuit breaker 4 1067.00 NDN416A 16A 10kA miniature circuit breaker 4 1067.00 NDN420A 20A 10kA miniature circuit breaker 4 1067.00 NDN425A 25A 10kA miniature circuit breaker 4 1067.00 NDN432A 32A 10kA miniature circuit breaker 4 1067.00 NDN440A 40A 10kA miniature circuit breaker 4 1067.00 NDN450A 50A 10kA miniature circuit breaker 4 1162.00 NDN463A 63A 10kA miniature circuit breaker 4 1162.00 HMD480 80A 15kA miniature circuit breaker 6 2894.00 HMD490 100A 15kA miniature circuit breaker 6 4518.00 HMD499 125A 15kA miniature circuit breaker 6 5026.00 B-2

Miniature circuit breakers (MCBs) 10/15kA For the protection and control of circuits against overload and short circuits. Suitable for commercial and industrial installations. Breaking capacity: Field fittable accessories (see page B-5) SANS / IEC 60947-2 15kA - auxiliary/alarm contacts IEC 60898 10kA - shunt trip device - undervoltage release Voltage rating: 240/400V 50-60Hz - earth leakage designation current breaking width in rating capacity 17.5mm NCN116A NCN / HMC series 10/15kA C curve (5-10 In) Single pole NCN106A 6A 15kA miniature circuit breaker 1 219.00 1 PP NCN110A 10A 15kA miniature circuit breaker 1 219.00 NCN116A 16A 15kA miniature circuit breaker 1 219.00 NCN120A 20A 15kA miniature circuit breaker 1 219.00 NCN125A 25A 15kA miniature circuit breaker 1 254.00 NCN132A 32A 15kA miniature circuit breaker 1 254.00 NCN140A 40A 15kA miniature circuit breaker 1 254.00 NCN150A 50A 15kA miniature circuit breaker 1 254.00 NCN163A 63A 15kA miniature circuit breaker 1 280.00 HMC180 80A 15kA miniature circuit breaker 1.5 762.00 HMC190 100A 15kA miniature circuit breaker 1.5 838.00 HMC199 125A 15kA miniature circuit breaker 1.5 914.00 NCN232A Two pole NCN206A 6A 15kA miniature circuit breaker 2 605.00 2 PP NCN210A 10A 15kA miniature circuit breaker 2 605.00 NCN216A 16A 15kA miniature circuit breaker 2 605.00 NCN220A 20A 15kA miniature circuit breaker 2 605.00 NCN225A 25A 15kA miniature circuit breaker 2 675.00 NCN232A 32A 15kA miniature circuit breaker 2 675.00 NCN240A 40A 15kA miniature circuit breaker 2 675.00 NCN250A 50A 15kA miniature circuit breaker 2 675.00 NCN263A 63A 15kA miniature circuit breaker 2 675.00 HMC280 80A 15kA miniature circuit breaker 3 1727.00 HMC290 100A 15kA miniature circuit breaker 3 1777.00 HMC299 125A 15kA miniature circuit breaker 3 1828.00 NCN320A Triple pole NCN306A 6A 15kA miniature circuit breaker 3 833.00 3 PP NCN310A 10A 15kA miniature circuit breaker 3 833.00 NCN316A 16A 15kA miniature circuit breaker 3 833.00 NCN320A 20A 15kA miniature circuit breaker 3 833.00 NCN325A 25A 15kA miniature circuit breaker 3 858.00 NCN332A 32A 15kA miniature circuit breaker 3 858.00 NCN340A 40A 15kA miniature circuit breaker 3 858.00 NCN350A 50A 15kA miniature circuit breaker 3 858.00 NCN363A 63A 15kA miniature circuit breaker 3 858.00 HMC380 80A 15kA miniature circuit breaker 4.5 1929.00 HMC390 100A 15kA miniature circuit breaker 4.5 2234.00 HMC399 125A 15kA miniature circuit breaker 4.5 2792.00 Four pole NCN406A 6A 15kA miniature circuit breaker 4 1447.00 4 PP NCN410A 10A 15kA miniature circuit breaker 4 1447.00 NCN416A 16A 15kA miniature circuit breaker 4 1447.00 NCN420A 20A 15kA miniature circuit breaker 4 1447.00 NCN425A 25A 15kA miniature circuit breaker 4 1447.00 NCN432A 32A 15kA miniature circuit breaker 4 1828.00 NCN440A 40A 15kA miniature circuit breaker 4 1828.00 NCN450A 50A 15kA miniature circuit breaker 4 2184.00 NCN463A 63A 15kA miniature circuit breaker 4 2335.00 NCN440A HMC480 80A 15kA miniature circuit breaker 6 3046.00 HMC490 100A 15kA miniature circuit breaker 6 3250.00 HMC499 125A 15kA miniature circuit breaker 6 3808.00 B-3

High fault level (MCBs) 15/20/25kA NRN116A NRN232A NRN320A For the protection and control of circuits against overload and short circuits. Suitable for commercial and industrial installations. Breaking capacity: Field fittable accessories (see page B-5) SANS / IEC 60947-2 6-25A 25kA - auxiliary/alarm contacts 32-40A 20kA - shunt trip device 50-63A 15kA - undervoltage release - earth leakage Voltage rating: 240/400V 50-60Hz designation NRN series 15-25kA C curve (5-10 In) current breaking width in rating capacity 17.5mm Single pole NRN106A 6A 25kA miniature circuit breaker 1 270.00 1 PP NRN110A 10A 25kA miniature circuit breaker 1 270.00 NRN116A 16A 25kA miniature circuit breaker 1 270.00 NRN120A 20A 25kA miniature circuit breaker 1 270.00 NRN125A 25A 25kA miniature circuit breaker 1 270.00 NRN132A 32A 20kA miniature circuit breaker 1 305.00 NRN140A 40A 20kA miniature circuit breaker 1 305.00 NRN150A 50A 15kA miniature circuit breaker 1 318.00 NRN163A 63A 15kA miniature circuit breaker 1 318.00 Two pole NRN206A 6A 25kA miniature circuit breaker 2 508.00 2 PP NRN210A 10A 25kA miniature circuit breaker 2 508.00 NRN216A 16A 25kA miniature circuit breaker 2 508.00 NRN220A 20A 25kA miniature circuit breaker 2 508.00 NRN225A 25A 25kA miniature circuit breaker 2 508.00 NRN232A 32A 20kA miniature circuit breaker 2 508.00 NRN240A 40A 20kA miniature circuit breaker 2 559.00 NRN250A 50A 15kA miniature circuit breaker 2 559.00 NRN263A 63A 15kA miniature circuit breaker 2 559.00 Triple pole NRN306A 6A 25kA miniature circuit breaker 3 812.00 3 PP NRN310A 10A 25kA miniature circuit breaker 3 812.00 NRN316A 16A 25kA miniature circuit breaker 3 812.00 NRN320A 20A 25kA miniature circuit breaker 3 812.00 NRN325A 25A 25kA miniature circuit breaker 3 812.00 NRN332A 32A 20kA miniature circuit breaker 3 812.00 NRN340A 40A 20kA miniature circuit breaker 3 864.00 NRN350A 50A 15kA miniature circuit breaker 3 864.00 NRN363A 63A 15kA miniature circuit breaker 3 864.00 NRN440A Four pole NRN406A 6A 25kA miniature circuit breaker 4 1575.00 4 PP NRN410A 10A 25kA miniature circuit breaker 4 1575.00 NRN416A 16A 25kA miniature circuit breaker 4 1575.00 NRN420A 20A 25kA miniature circuit breaker 4 1575.00 NRN425A 25A 25kA miniature circuit breaker 4 1727.00 NRN432A 32A 20kA miniature circuit breaker 4 1727.00 NRN440A 40A 20kA miniature circuit breaker 4 1727.00 NRN450A 50A 15kA miniature circuit breaker 4 2335.00 NRN463A 63A 15kA miniature circuit breaker 4 2335.00 KB190C Connection and MCB accessories KB263C KB190C 20mm² 1 pole 1 pole insulated busbar 24 157.00 KB263C 10mm² 2 pole 2 pole insulated busbar 24 330.00 KB363C KB363C 10mm² 3 pole 3 pole insulated busbar 24 362.00 KB380B 16mm² (1 meter) 3 pole 3 pole insulated busbar 57 657.00 KB463C 10mm² 4 pole 4 pole insulated busbar 24 584.00 KF83B KF83C MZN175 KZ022 end protection caps for busbar KB263C 22.00 KZ023A end protection caps for busbar KB363C, KB380B 22.00 KZ024 end protection caps for busbar KB463C 23.00 KF84A enlarged terminal 25mm² (lateral connection) 25.00 KF83B enlarged terminal 2 x 25mm² (lateral connection) 67.00 KF83C enlarged terminal 25mm² (top or lateral connection) 36.00 MZN130 MZN131 LZ060 dummy module / heat dissipation insert 0.5 7.00 MZN175 padlocking device for toggle of MCB 1 126.00 JP024 MCB blanking strip (breakable sections) 24 38.00 MZN130 terminal cover / screw cap for HLF, HMC, HMD 1.5 68.00 MZN131 phase seperators for HLF, HMC, HMD (set of 3) 102.00 B-4

MCB auxiliaries / Accessories All auxiliaries are common to both single and multi-pole circuit breakers as well as RCCBs and RCBOs. Auxiliaries are fitted to the left side of the device. Field fittable accessories for MCB s: NF, HMC, NGN, NDN, HMD, HLF, NRN Auxiliary contacts Alarm contacts Shunt trip device Undervoltage release width in 17.5 mm Auxiliaries and tripping devices for MCBs and RCDs MZ201 MZ201 1NO + 1NC 6A 230Vac auxiliary contact block 0.5 347.00 indication of main contact status MZ202 1NO + 1NC 6A 230Vac alarm contact block 0.5 347.00 indicates a fault overcurrent or short circuit MZ203 230-415Vac shunt trip device 1 453.00 permits remote tripping of the device MZ202 MZ204 24-48 Vac / 12-48Vdc shunt trip device 1 379.00 permits remote tripping of the device MZ203 MZ206 230Vac under voltage release 1 453.00 MCB can only close when voltage above 70% of Un. trips when voltage below 35% of Un. MZ212 230Vac over voltage release 1 453.00 trips the protection device in case of overvoltage Add-on earth leakage devices for MCBs For connection to all MCBs to be mounted to the right side of 2, 3, 4 pole circuit breakers. The combined unit provides effective protection against overloads, short circuits as well as earth leakage faults. Features independent indication of earth fault or overload when tripped. BD264 current rating sensitivity poles width in 17.5 mm BD264 63A 30 ma 2 pole earth leakage device 2 914.00 BD364 63A 30 ma 3 pole earth leakage device 3 1067.00 BD464 63A 30 ma 4 pole earth leakage device 3 1321.00 BF264 63A 300 ma 2 pole earth leakage device 2 1269.00 BF364 63A 300 ma 3 pole earth leakage device 3 1369.00 BF464 63A 300 ma 4 pole earth leakage device 3 2027.00 Add-on earth leakage devices for HLF - HMC - HMD circuit breakers Fixed sensitivity BDC280E 125A 30 ma 2 pole earth leakage device 6 1777.00 BDC380E 125A 30 ma 3 pole earth leakage device 6 1981.00 BDC480E 125A 30 ma 4 pole earth leakage device 6 2133.00 BTC380E Adjustable sensitivity Adjustable trip delay - 0.3-0.5-1A - 0-60 - 150ms BTC280E 125A 30 ma 2 pole earth leakage device 6 2031.00 BTC380E 125A 30 ma 3 pole earth leakage device 6 2234.00 BTC480E 125A 30 ma 4 pole earth leakage device 6 2488.00 B-5

Earth leakage protection CD241J CD464J Residual Current Devices (RCDs) Nuisance tripping Without overload protection Hager earth leakage devices are protected against nuisance tripping Description caused by transient leakage current. To automatically open a circuit in the event of an earth leakage faulty. Field fittable (see page B5) Suitable for domestic, commercial and Auxiliaries and remote operators (CD RCDs only) industrial installations. mechanical life: 40,000 operations Nominal voltage: (2 pole) 110/240V 50Hz specification SABS IEC 601008 / SANS 767-1 (4 pole) 240/415V 50Hz 30mA sensitivity overload sensitivity width in poles rating (A) (ma) 17.5mm CD226J 25A 30 ma 2 pole earth leakage device 2 431.00 CD241J 40A 30 ma 2 pole earth leakage device 2 431.00 CD264J 63A 30 ma 2 pole earth leakage device 2 539.00 CD285Z 100A 30 ma 2 pole earth leakage device 2 1101.00 CD464J 63A 30 ma 4 pole earth leakage device 4 862.00 CD485Z 100A 30 ma 4 pole earth leakage device 4 1751.00 100/300mA sensitivity (selective ) CE264J 63A 100 ma 2 pole earth leakage device 2 681.00 CF264J 63A 300 ma 2 pole earth leakage device 2 812.00 CF285Z 100A 300 ma 2 pole earth leakage device 4 1219.00 CF464J 63A 300 ma 4 pole earth leakage device 4 1676.00 CF485Z 100A 300 ma 4 pole earth leakage device 4 2957.00 AD890J Combination MCB/RCD (circuit breaker and earth leakage combination) Earth leakage with overload and short circuit protection AD Series 4.5kA C curve 5-10In AD866J 16A 30 ma 2 pole earth leakage + MCB 2 965.00 AD870J 20A 30 ma 2 pole earth leakage + MCB 2 965.00 AD875J 25A 30 ma 2 pole earth leakage + MCB 2 965.00 AD882J 32A 30 ma 2 pole earth leakage + MCB 2 965.00 AD890J 40A 30 ma 2 pole earth leakage + MCB 2 965.00 Industrial electronic earth leakage relay with separate toroid HR500 HR510 Incorporating test and reset buttons and LED indication Fixed sensitivity, instantaneous trip HR500 220/240V 30 ma 4 pole entry level e/leakage relay 1 1423.00 HR502 220/240V 300 ma 4 pole entry level e/leakage relay 1 1373.00 Adjustable sensitivity and trip delay Selectable In threshold: 0.03A/0.1A/0.3A/0.5A/1A/10A (30mA - 10A) Selectable trip delay: 0/0.15/0.35/0.55/1sec/3sec (0-3sec) HR520 HR510 220/240V selectable 4 pole earth leakage relay 3 1913.00 HR520 as above with fault current indication and 50% pre-alarm output 3 2207.00 HR700 Above prices do not include VAT. E&OE HR743 Separate torroid sensors HR700 round hole torroid dia 30 mm DIN rail mountable 883.00 HR742 round hole torroid dia 70 mm standard torroid 932.00 HR743 round hole torroid dia 105 mm standard torroid 1717.00 HR745 round hole torroid dia 210 mm standard torroid 3433.00 HR830 rectangular hole torroid dia 70 x 175 mm standard torroid 8582.00 B-6

Isolators SB series modular isolators (switch disconnectors) For use as a switch disconnector in all s of circuits Green/red indication on handle provides positive contact indication SANS - IEC 60947-3 utilisation category: AC 22B current rating (A) switching poles width in 17.5mm SB132 SB series modular isolators (switch disconnectors) SB232 SBN132 32A on - off 1 pole modular isolator switch 1 81.00 SBN163 63A on - off 1 pole modular isolator switch 1 108.00 SBN190 100A on - off 1 pole modular isolator switch 1 135.00 SBN199 125A on - off 1 pole modular isolator switch 1 184.00 SBN232 32A on - off 2 pole modular isolator switch 2 108.00 SBN263 63A on - off 2 pole modular isolator switch 2 162.00 SBN290 100A on - off 2 pole modular isolator switch 2 189.00 SBN299 125A on - off 2 pole modular isolator switch 2 321.00 SBN332 32A on - off 3 pole modular isolator switch 3 162.00 SBN363 63A on - off 3 pole modular isolator switch 3 216.00 SBN390 100A on - off 3 pole modular isolator switch 3 270.00 SBN399 125A on - off 3 pole modular isolator switch 3 508.00 SBN399 SBN432 32A on - off 4 pole modular isolator switch 4 250.00 SBN463 63A on - off 4 pole modular isolator switch 4 349.00 SBN490 100A on - off 4 pole modular isolator switch 4 967.00 SBN499 125A on - off 4 pole modular isolator switch 4 1058.00 Changeover switches SFH125 25A on - on 1 pole 2 way changeover switch 1 114.00 SFH225 25A on - on 2 pole 2 way changeover switch 2 265.00 SFH125 SFT125 25A on-off-on 1 pole centre off changeover switch 1 130.00 SFT140 40A on-off-on 1 pole centre off changeover switch 1 130.00 SFT240 40A on-off-on 2 pole centre off changeover switch 2 265.00 SFT440 40A on-off-on 4 pole centre off changeover switch 4 512.00 SF263 63A on-off-on 2 pole centre off changeover switch 4 373.00 SF463 63A on-off-on 4 pole centre off changeover switch 8 1007.00 SFH225 Control transformers (modular DIN rail mount) supply output power width in voltage voltage (VA) 17.5mm ST312 230V 12/24V 25VA modular safety transformer 4 507.00 ST314 230V 12/24V 40VA modular safety transformer 4 571.00 ST315 230V 12/24V 63VA modular safety transformer 6 766.00 ST303 230V 8/12V 8VA modular bell transformer 4 317.00 ST305 230V 8/12V 16VA modular bell transformer 4 527.00 ST314 Audible devices (modular DIN rail mount) SU213 230V 6.5VA 85 dba modular buzzer 1 193.00 SU214 8/12Vac 4.0VA 78 dba modular buzzer 1 193.00 SU215 230V 6.5VA 78 dba modular buzzer 1 193.00 Fuse holders (modular DIN rail mount) For protection and control of circuits against overloads and short circuits Short-circuit resistance with 10x38 mm fuse link: 80kA SU213 LS501 32A 1 pole modular cylindrical fuse holder 1 43.00 LS502 32A 2 pole modular cylindrical fuse holder 2 106.00 Control and indicating devices LED indicating lights (10 000 hrs) LS502 SVN... SVN121 230Vac green modular LED indicating light 1 130.00 SVN122 230Vac red modular LED indicating light 1 130.00 SVN123 230Vac amber modular LED indicating light 1 130.00 SVN126 230Vac grn+red modular LED indicating light 1 183.00 SVN223 230Vac red/wht/blu modular LED p/light for phase indication 1 233.00 SVN131 12-48Vac/dc green modular LED indicating light 1 130.00 SVN132 12-48Vac/dc red modular LED indicating light 1 130.00 SVN351 1no+1nc green modular momentary pushbutton 1 183.00 SVN391 1no+1nc grn+red double pushbutton (grn NO / red NC) 1 182.00 SVN411 1no green modular pushbutton + green pilot light 1 169.00 B-7

Modular relays / Contactors ERC216 Modular DIN rail mounting (same cutout as MCBs) One and two module contactors feature economy low consumption, low heat dissipation coils Four ratings: 16A, 25A, 40A, 63A rated power AC-1 AC-3 coil contact width in (A) kw (400V) voltage config 17.5mm Control relays with manual override selector (I-auto-O) ERC216 16A 230Vac modular eco control relay 2NO 1 247.00 ERC218 16A 230Vac modular eco control relay 1NO+1NC 1 247.00 ERC416 16A 1.7kW 230Vac modular eco control relay 4NO 2 488.00 ERC418 16A 1.7kW 230Vac modular eco control relay 2NO+2NC 2 481.00 ESC225 ERC418 ESC425 Modular contactors (230 Vac 50/60 Hz) Modular DIN rail mounting ESC225 25A 230Vac modular eco control relay 2NO 1 307.00 ESC226 25A 230Vac modular eco control relay 2NC 1 307.00 ESC227 25A 230Vac modular eco control relay 1NO+1NC 1 313.00 ESC425 25A 2.6kW 230Vac modular eco control relay 4NO 2 437.00 ESC427 25A 2.6kW 230Vac modular eco control relay 2NO+2NC 2 446.00 ESC240 40A 7.8kW 230Vac modular std contactor 2NO 3 569.00 ESC440 40A 7.8kW 230Vac modular std contactor 4NO 3 687.00 ESC441 40A 7.8kW 230Vac modular std contactor 4NC 3 687.00 ESC442 40A 7.8kW 230Vac modular std contactor 2NO+2NC 3 687.00 ESC263 63A 10kW 230Vac modular std contactor 2NO 3 744.00 ESC463 63A 10kW 230Vac modular std contactor 4NO 3 781.00 ESC464 63A 10kW 230Vac modular std contactor 4NC 3 793.00 ESC465 63A 10kW 230Vac modular std contactor 2NO+2NC 3 883.00 ESC463 ESC225S ESC425S ESC463S Modular contactors with hum-free coil Low consumption DC coil with integrated rectifier No humming while energised / low switching noise ESC225S 25A 230Vac/dc hum-free eco contactor 2NO 1 293.00 ESD225S 25A 24Vac/dc hum-free eco contactor 2NO 1 293.00 ESL225S 25A 12Vac/dc hum-free eco contactor 2NO 1 293.00 ESC425S 25A 2.6kW 230Vac/dc hum-free eco contactor 4NO 2 558.00 ESD425S 25A 2.6kW 24Vac/dc hum-free eco contactor 4NO 2 558.00 ESL425S 25A 2.6kW 12Vac/dc hum-free eco contactor 4NO 2 549.00 ESC440S 40A 7.8kW 230Vac/dc hum-free contactor 4NO 3 837.00 ESD440S 40A 7.8kW 24Vac/dc hum-free contactor 4NO 3 837.00 ESL440S 40A 7.8kW 12Vac/dc hum-free contactor 4NO 3 837.00 ESC463S 63A 10kW 230Vac/dc hum-free contactor 4NO 3 976.00 ESD463S 63A 10kW 24Vac/dc hum-free contactor 4NO 3 976.00 ESL463S 63A 10kW 12Vac/dc hum-free contactor 4NO 3 976.00 Does not accept clip-on auxiliary Auxiliary contact for all above relays/contactors (except ) ESC080 Ith 6A clip-on auxiliary contact 1NO+1NC 0.5 228.00 Modular stepping relays (pulse ON - pulse OFF ) EPN515 16A 230Vac modular stepping relay 1NO+1NC 1 247.00 EPN518 16A 24Vac/12Vdc modular stepping relay 1NO+1NC 1 247.00 EPN519 16A 12Vac modular stepping relay 1NO+1NC 1 247.00 ESC080 EPN051 EPN053 Auxiliary for all above stepping relays EPN051 Ith 6A clip-on auxiliary contact 1NO+1NC 0.5 211.00 EPN053 Ith 6A impulse converter for maintained contact 1 changeover 0.5 211.00 Above prices do not include VAT. E&OE B-8

Modular time switches time range min. contact width in reserve setting config 17.5mm EH010 EH211 Time switches 16A 250V electro-mechanical 230Vac 50Hz AC1 Slimline 1 module wide (18 mm) EH010 24 hr 15 min no 1 NO time switch 1 442.00 EH011 24 hr 15 min 200 hrs 1 NO time switch 1 463.00 Standard 2/3 module wide (36 mm) (clock hand indicates time) EH210 24 hr 30 min no 1 c/over time switch 2 496.00 EH211 24 hr 30 min 200 hrs 1 c/over time switch 2 786.00 EH110 24 hr 15 min no 1 c/over time switch 3 495.00 EH111 24 hr 15 min 200 hrs 1 c/over time switch 3 782.00 EH171 7 day 2 hr 200 hrs 1 c/over time switch 3 926.00 Dual dial (1 dial 7 day / 1 dial 24hr) EH111 EH191 7 day / 24 hr 15 min / 2 hr 200 hrs 1 c/over time switch 5 1335.00 Digital time switches (programmable via buttons or via PC programmable key) Indicates date and time (pre-programmed at factory) Visualisation of daily profile via incorporated bar-graph display Programmable via front keypad (even without suppy) or program key EG005 Up to 56 program steps EH191 Basic version (programming key to be ordered separately) 230Vac EG103B 7 day 1 min 5 years 1 c/over 2 1083.00 Exclusive version (supplied with programming key) 230Vac Impulse time switch (suitable for school-bell ringing / lunch-tea break) Programmable pulses of 1 sec - 30 min duration Holiday mode programmable (between two dates) Backlit display (for indication in badly illuminated locations) EG103B EG103E 7 day 1 sec 5 years 1 c/over 2 1552.00 EG203E 7day +7 day 1 sec 5 years 2 c/over 2 1717.00 12 / 24Vac/dc (supplied with programming key) EG103V 7 day 1 sec 5 years 1 c/over 2 1585.00 4 Channel yearly time switch (300 program steps) EG103E EG004 EG005 EG403E week 1 min 10 years 2 c/o + 2 NC 4 6854.00 Accessories EG003U PC interface module and programming software for EG series 2112.00 EG004 locking key (for disabling front keypad) 133.00 EG005 programming key (for down / up loading of program) EG103/203E 201.00 EG002 programming key (for down / up loading of program) EG403E 740.00 Modular electronic timers (10A 230V changeover) EG403E Multi - range: 0.1s-10h Multi-voltage: 12-230Vac +-10% 10A 230V changeover output EZN001 on-delay multi-range (modular electronic timer) 1 862.00 EZN002 delay-on de-energisation (modular electronic timer) 1 984.00 EZN003 interval (modular electronic timer) 1 862.00 EZN004 pulse controlled interval (modular electronic timer) 1 969.00 EZN006 multi-function on-delay / off-delay / interval / repeat timer 1 1076.00 EZN006 B-9

Surge protection devices (SPD) / kwh meters SPN802 Modular surge protection devices SANS/IEC 61643-1 For the protection of low voltage equipment against transient voltages and current surges from atmospheric origins (lightning) as well as transients produced by switching characteristics such as in switching of distribution networks, transformers, motors, etc. poles Up Class 1 and class 2 combined surge protection device Lightning and surge-voltage protection in one device Iimp Imax width in 10/350 μs 8/20 μs 17.5mm Replaceable plug-in cartridges SPN802 3ph+N 1.5kV 100kA class 1+2 surge protector 8 19799.00 SPN802R 3ph+N 1.5kV 100kA class 1+2 SPD 8 23278.00 With remote signalling contact for monitoring Class 2 surge protection (modular plug-in) Suitable for second level protection in distribution panels where 1 protectors are installed or areas not exposed to direct lightning strikes and with no external lightning protection system. Protection for domestic, industrial and commercial buildings Replaceable plug-in cartridges Imax 40kA (8/20μs) SPN240D SPN440R SPN140D 1P 1.5kV 40kA class 2 surge protector 1 955.00 SPN140R 1P 1.5kV 40kA class 2 surge protector 1 1635.00 SPN240D 1ph+N 1.5kV 40kA class 2 surge protector 2 2059.00 SPN240R 1ph+N 1.5kV 40kA class 2 surge protector 2 2328.00 SPN440D 3ph+N 1.5kV 40kA class 2 surge protector 4 3802.00 SPN440R 3ph+N 1.5kV 40kA class 2 surge protector 4 4954.00 With remote signalling contact for monitoring Imax 15kA (8/20μs) SPN215D 1ph+N 1.5kV 15kA class 2 surge protector 2 1848.00 SPN415D 3ph+N 1.5kV 15kA class 2 surge protector 4 2587.00 Replacement cartridges for above surge protection devices SPN040D phase replacement cartridge for protectors SPN240/440 1 793.00 SPN015D phase replacement cartridge for protectors SPN215/415 1 793.00 SPN040N neutral replacement cartridge for protectors SPN2/4 1 898.00 SPN040D Energy meters (kwh meters) (modular DIN rail mounting) backlit LCD display Class 1 according to IEC 62 053-21 and EN 50470 Impulse output Total counter and partial (resettable) counter LED indication blinks according to consumption (1 pulse = 100wh) Accuracy: 1% current operation Single-phase (kwh meter) 63A (direct reading) Displays consumption of active energy and instantaneous power consumption EC150 63A direct reading single-phase kwh meter 3 1883.00 EC150 Three-phase (kwh meters) 63/100A (direct reading) Displays consumption of active energy and instantaneous power consumption Protected against phase/neutral inversion Adaptable to three phase with or without neutral, 230V or 400V between lines EC350 63A direct reading three-phase kwh meter 4 3765.00 EC360 100A direct reading three-phase kwh meter 7 6191.00 Three phase (kwh meters) up to 6000A (connection via current transformer - CT) EC350 Displays consumption of active energy and reactive energy Displays instantaneous power consumption No polarity for CT connection Adaptable to three phase with or without neutral, 230V or 400V between lines EC370 6000A CT operated three-phase kwh meter 4 3814.00 B-10

Moulded case circuit breakers (MCCB) 16-1600A H3 circuit breakers conform to IEC/EN 60947-2 standards and to all major international standards and performance categories. Suitable for co-ordinated installations in all applications Thermal magnetic and electronic release Calibrated at 50ºC Cascading with MCBs (see cascading chart Annex-11) Fixed Fixed Fixed Standard Standard Type HHA...Z HHB...Z HHD...U HNA...U HNB...U No. of poles 1-2-3-4 3-4 3-4 3-4 3-4 Electrical Ratings (IEC 60947-2) TM TM TM TM TM Rated uninterrupted current Iu (A) at 50ºC 160 250 400 160 250 Rated voltage Ue Vac 440 440 690 690 690 Rated voltage Ue Vdc 250 250 250 250 250 Rated insulation voltage Ui (Vac) 690 800 800 800 800 Rated impulse withstand voltage Uimp (kv) 8 8 8 8 8 Utilization category A A A A A 16 200 400 25 250 20 250 40 25 63 32 100 40 125 Rated current of release In (A) 50 160 63 80 100 125 160 Performance 220/230Vac (Icu) ka 35 35 35 85 85 380/415Vac (Icu) ka 25 25 25 40 40 Rated ultimate short-circuit, breaking capacity, (Icu) 50-60Hz 480/525Vac (Icu) ka 18 25 22 25 25 660/690Vac (Icu) ka 6 6 6 6 250Vdc (2P) (Icu) ka 25 25 25 25 25 Service breaking capacity Ics (%Icu) 100% 100% 100% 50% 50% Rated making capacity Icm (ka) @ 400Vac 52.5 52.5 52.5 84 84 Durability mechanical operations 20 000 20 000 15 000 20 000 20 000 electrical operations 10 000 10 000 4500 10 000 10 000 Adjustable thermal release fixed 1 x In fixed 1 x In 0.63-1 In 0.63-0.8-1 In 0.63-0.8-1 In Adjustable magnetic >10 In(No adj.) >10 In(No adj.) 6-12 In >10 In 5-11 In Time delay (Electronic release) Suitability for isolation Thermal magnetic release Electronic release Accessories Auxiliary/shunt trip/under volt. release Motor operator/mechan. interlocks Dimensions frame x160 x250 h400 x160 x250 High (with extended terminals) mm 130 165 260 130 165 Wide (3 pole) mm 75 105 140 75 105 Deep (without toggle) mm 68 68 97 68 68 B-11 Above prices do not include VAT. E&OE

Moulded case circuit breakers (MCCB) 16-1600A Standard Standard Standard Standard Standard High Fault High Fault High Fault High Fault HND...U HND...U HNE...U HNE...U HNF...U HEG...U HED...U HEE...U HEF...U 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 TM LSI LSI LSI LSI TM LSI LSI LSI 400 630 800 1000 1250/1600 250 630 800/1000 1250/1600 690 690 690 690 690 690 690 690 690 250 250 250 250 250 250 250 250 250 690 690 690 690 690 690 690 690 690 8 8 8 8 8 6 8 8 8 A A A A A A A A A 400 630 800 1000 1250 63 630 800 1250 1600 100 1000 1600 160 250 85 85 85 85 100 85 100 100 100 50 50 50 50 50 65 70 70 70 30 30 30 30 45 25 65/75 65 70 20 20 20 20 25 7.5 20 20 45 40 40 100% 100% 100% 100% 100% 55% 85% 70% 70% 110 110 110 110 110 143 154 154 154 15 000 15 000 15 000 15 000 15 000 30 000 15 000 15 000 15 000 4500 4500 4500 4500 4500 10 000 4500 4500 4500 0.63-1 In 0.4-1 In 0.4-1 In 0.4-1 In 0.4-1 In 0.63-1 In 0.4-1 In 0,4-1 In 0.4-1 In 6-12 In 2.5-8 In 2.5-10 In 2.5-8 In 2.5-10 In 6-8-11-13 x In 2.5-10 In 2.5-10 In (800A)/2.5-8 In (1000A) 2.5-10 In 0.1-0.2 sec 0.1-0.2 sec 0.1-0.2 sec 0.1-0.2 sec 0.1-0.2 sec 0.1-0.2 sec 0.1-0.2 sec h400 h630 h1000 h1000 h1600 h250 h630 h1000 h1600 260 260 273/433 273/433 370/570 165 260 273/433 370/570 140 140 210 210 210 105 140 210 210 97 97 100 145 140 68 97 100 140 Above prices do not include VAT. E&OE B-12

Moulded case circuit breakers (MCCB s) 25kA / 50kA Standards: SANS / IEC 60947-2 clip-in accessories Mechanical test button on facia Auxiliary contacts Integrated padlock facility on toggle Alarm contacts Cascading with MCBs (see chart Annex 11) Shunt trip device Lockable thermal/magnetic settings Undervoltage release Window indicating presence of: auxiliary/alarm contacts, shunt trip, UV release (40 ka version) thermal current rated ka 415V (Icu) poles frame Fixed thermal / magnetic trip 25 ka HHA125Z Fixed: thermal 1 x In / magnetic >10 x In HHA016Z 16A 25kA 3 pole moulded case CB x160 1232.00 HHA020Z 20A 25kA 3 pole moulded case CB x160 1232.00 HHA025Z 25A 25kA 3 pole moulded case CB x160 1232.00 HHA032Z 32A 25kA 3 pole moulded case CB x160 1232.00 HHA040Z 40A 25kA 3 pole moulded case CB x160 1232.00 HHA050Z 50A 25kA 3 pole moulded case CB x160 1232.00 HHA063Z 63A 25kA 3 pole moulded case CB x160 1232.00 HHA080Z 80A 25kA 3 pole moulded case CB x160 1232.00 HHA100Z 100A 25kA 3 pole moulded case CB x160 1232.00 HHA125Z 125A 25kA 3 pole moulded case CB x160 1305.00 HHA160Z 160A 25kA 3 pole moulded case CB x160 1595.00 HHB200Z 200A 25kA 3 pole moulded case CB x250 2706.00 HHB250Z 250A 25kA 3 pole moulded case CB x250 2706.00 HNA025U HNB250U TM: adjustable thermal 0.63-1 x In / adjustable magnetic 6-12 x In HHD400U 252-400A 25kA 3 pole moulded case CB h400 7247.00 Adjustable thermal / magnetic trip 40 ka TM: adjustable thermal 0.63-0.8-1 x In / fixed magnetic >10 x In Three pole HNA025U 16-25A 40kA 3 pole moulded case CB x160 1353.00 HNA040U 25-40A 40kA 3 pole moulded case CB x160 1353.00 HNA063U 40-63A 40kA 3 pole moulded case CB x160 1353.00 HNA100U 63-100A 40kA 3 pole moulded case CB x160 1353.00 HNA125U 80-125A 40kA 3 pole moulded case CB x160 1353.00 HNA160U 101-160A 40kA 3 pole moulded case CB x160 1643.00 HNB250U 160-250A 40kA 3 pole moulded case CB x250 3672.00 Four pole HNA026U 16-25A 40kA 4 pole moulded case CB x160 1827.00 HNA041U 25-40A 40kA 4 pole moulded case CB x160 1827.00 HNA064U 40-63A 40kA 4 pole moulded case CB x160 1827.00 HNA101U 63-100A 40kA 4 pole moulded case CB x160 1827.00 HNA126U 80-125A 40kA 4 pole moulded case CB x160 1827.00 HNA161U 101-160A 40kA 4 pole moulded case CB x160 2218.00 HNB251U 160-250A 40kA 4 pole moulded case CB x250 4977.00 Adjustable thermal / magnetic trip 50 ka HND630H TM: adjustable thermal 0.63-1 x In / adjustable magnetic 6-12 x In HND400H 252-400A 50 ka 3 pole moulded case CB h400 8552.00 HND401U 252-400A 50 ka 4 pole moulded case CB h400 11545.00 Adjustable electronic release (LSI) 50 ka LSI: adjustable thermal 0.4-1 x In / fixed magnetic 2.5-8 x Ir / time 0.1-0.2sec HND630H 252-630A 50 ka 3 pole moulded case CB h630 12078.00 HNE800H 320-800A 50 ka 3 pole moulded case CB h1000 15943.00 HNE970U 400-1000A 50 ka 3 pole moulded case CB h1000 24059.00 HNF980U 500-1250A 50 ka 3 pole moulded case CB h1600 29954.00 HNF990U 640-1600A 50 ka 3 pole moulded case CB h1600 38166.00 HNE970U HND631U 252-630A 50 ka 4 pole moulded case CB h630 16306.00 HNE801U 320-800A 50 ka 4 pole moulded case CB h1000 21523.00 HNE971U 400-1000A 50 ka 4 pole moulded case CB h1000 32480.00 HNF981U 500-1250A 50 ka 4 pole moulded case CB h1600 40437.00 HNF991U 640-1600A 50 ka 4 pole moulded case CB h1600 51517.00 B-13

High fault level circuit breakers 65/70kA HEG063U Standards: SANS / IEC 60947-2 clip-in accessories Mechanical test button on facia Auxiliary contacts Cascading with MCBs (see chart Annex 11) Alarm contacts Lockable thermal/magnetic settings Shunt trip device Undervoltage release thermal current rated ka 415V (Icu) poles frame Adjustable thermal / magnetic trip 65 ka TM: adjustable thermal 0.63-1 x In / magnetic 6-8 - 11-13 x In HEG063U 40-63A 65kA 3 pole moulded case circuit breaker h250 3769.00 HEG100U 63-100A 65kA 3 pole moulded case circuit breaker h250 3769.00 HEG160U 100-160A 65kA 3 pole moulded case circuit breaker h250 4058.00 HEG250U 160-250A 65kA 3 pole moulded case circuit breaker h250 4349.00 HED630U Adjustable electronic release (LSI) 70 ka LSI: adjustable thermal 0.4-1 x In / fixed magnetic 2.5-8 x Ir / time 0.1-0.2sec HED400U 160-400A 70kA 3 pole moulded case circuit breaker h630 12078.00 HED630U 252-630A 70kA 3 pole moulded case circuit breaker h630 13528.00 HEE800U 320-800A 70kA 3 pole moulded case circuit breaker h1000 16668.00 HEE970U 400-1000A 70kA 3 pole moulded case circuit breaker h1000 26572.00 HEF980U 500-1250A 70kA 3 pole moulded case circuit breaker h1600 32852.00 HEF990U 640-1600A 70kA 3 pole moulded case circuit breaker h1600 45896.00 Four pole available on request HEE970U Load break switches (switch disconnectors / isolators) HCA125Z 125A 3 pole load break switch (isolator) x160 1136.00 HCA160Z 160A 3 pole load break switch (isolator) x160 1402.00 HCB250Z 250A 3 pole load break switch (isolator) x250 2609.00 HCD400H 400A 3 pole load break switch (isolator) h400 4832.00 HCD630H 630A 3 pole load break switch (isolator) h630 9179.00 HCE800U 800A 3 pole load break switch (isolator) h1000 13044.00 HCE970U 1000A 3 pole load break switch (isolator) h1000 19808.00 HCF980U 1250A 3 pole load break switch (isolator) h1600 28987.00 HCF990U 1600A 3 pole load break switch (isolator) h1600 33335.00 HCF990U HCA126Z 125A 4 pole load break switch (isolator) x160 1328.00 HCA161Z 160A 4 pole load break switch (isolator) x160 1556.00 HCB251Z 250A 4 pole load break switch (isolator) x250 3158.00 HCD401U 400A 4 pole load break switch (isolator) h400 4550.00 HCD631U 630A 4 pole load break switch (isolator) h630 8547.00 HCE801U 800A 4 pole load break switch (isolator) h1000 17610.00 HCE971U 1000A 4 pole load break switch (isolator) h1000 26741.00 HCF981U 1250A 4 pole load break switch (isolator) h1600 39133.00 HCF991U 1600A 4 pole load break switch (isolator) h1600 45002.00 Accessories for MCCBs and load break switches Auxiliary contacts 1NO + 1NC HXA021H 1NO + 1NC auxiliary contact 1NO+1NC for circuit breakers x160-250 275.00 HXC021H 1NO + 1NC auxiliary contact 1NO+1NC for circuit breakers h250-1600 588.00 HXA021H HXA024H 1NO + 1NC alarm contact 1NO+1NC for circuit breakers x160-250 275.00 HXC024H 1NO + 1NC alarm contact 1NO+1NC for circuit breakers h250-1600 588.00 HXA024H HXC004H HXC024H Shunt trip units (SH) HXA001H 24Vdc (SH) shunt trip device for circuit breakers x160-250 557.00 HXA003H 110Vac (SH) shunt trip device for circuit breakers x160-250 557.00 HXA004H 230Vac (SH) shunt trip device for circuit breakers x160-250 557.00 HXA005H 400Vac (SH) shunt trip device for circuit breakers x160-250 619.00 HXC001H 24Vdc (SH) shunt trip device for circuit breakers h250-1600 588.00 HXC003H 110Vac (SH) shunt trip device for circuit breakers h250-1600 588.00 HXC004H 230Vac (SH) shunt trip device for circuit breakers h250-1600 588.00 HXC005H 400Vac (SH) shunt trip device for circuit breakers h250-1600 619.00 B-14

MCCB accessories voltage frame Undervoltage release (UV) HXA011H 24Vdc (UV) undervoltage release for circuit breakers x160-250 959.00 HXA013H 110Vac (UV) undervoltage release for circuit breakers x160-250 959.00 HXA014H 230Vac (UV) undervoltage release for circuit breakers x160-250 959.00 HXA015H 440Vac (UV) undervoltage release for circuit breakers x160-250 1052.00 HXC011H 24Vdc (UV) undervoltage release for circuit breakers h250-630 959.00 HXC013H 110Vac (UV) undervoltage release for circuit breakers h250-630 959.00 HXC014H 230Vac (UV) undervoltage release for circuit breakers h250-630 959.00 HXC015H 440Vac (UV) undervoltage release for circuit breakers h250-630 1052.00 HXC014H HXE011H 24Vdc (UV) undervoltage release for circuit breakers h1000-1600 1052.00 HXE013H 110Vac (UV) undervoltage release for circuit breakers h1000-1600 1052.00 HXE014H 230Vac (UV) undervoltage release for circuit breakers h1000-1600 1052.00 HXE015H 440Vac (UV) undervoltage release for circuit breakers h1000-1600 1144.00 Rotary handles (padlockable in off position) HXA030H HXA030H direct mount front mount rotary handle for circuit breakers x160 1096.00 HXB030H direct mount front mount rotary handle for circuit breakers x250 1096.00 HXC030H direct mount front mount rotary handle for circuit breakers h250 866.00 HXD030H direct mount front mount rotary handle for circuit breakers h400/630 1450.00 HXE030H direct mount front mount rotary handle for circuit breakers h1000 1788.00 HXF030H direct mount front mount rotary handle for circuit breakers h1600 2465.00 Rotary handles (vari-depth door interlocking) HXA031H HXA031H vary-depth 200mm door interlocking rotary handle and shaft x160 1450.00 HXB031H vary-depth 200mm door interlocking rotary handle and shaft x250 1450.00 HXC031H vary-depth door interlocking rotary handle and shaft h250 1237.00 HXD031H vary-depth door interlocking rotary handle and shaft h400/630 1981.00 HXE031H vary-depth door interlocking rotary handle and shaft h1000 7102.00 HXF031H vary-depth door interlocking rotary handle and shaft h1600 7875.00 Terminals and mounting accessories HYD003H HYA033H DIN rail mounting adaptor x160 290.00 HYB033H DIN rail mounting adaptor x250 340.00 HYA036H (3 x 100mm) Din rail raiser (to align MCBs with MCCBs) 426.00 HYB001H (set of 3) 150 mm² collar terminals for cables x250 1933.00 HYD003H (set of 3) 240 mm² collar terminals for cables h400/630 2175.00 HYA027H HYA014H (3 pole) spreader link extended terminals x160 725.00 HYB011H (3 pole) spreader link extended terminals x250 822.00 HYC011H (3 pole) spreader link extended terminals h250 822.00 HYD014H (3 pole) spreader link extended terminals h400/630 1498.00 HYA027H (3 pole) terminal shrouds x160 436.00 HYB021H (3 pole) extended terminal shrouds x250 436.00 HYC021H (3 pole) extended terminal shrouds h250 436.00 HYD021H (3 pole) extended terminal shrouds h400/630 677.00 HYE021H (3 pole) extended terminal shrouds h1000 1353.00 HYE021H HYA019H (3 per set) spare interphase barriers x160 290.00 HYB019H (3 per set) spare interphase barriers x250 339.00 HYC019H (3 per set) spare interphase barriers h250 440.00 Special contained palm cable lugs for MCCBs A12-M6/15 50 mm² M6x15 mm contained palm cable lug (ea) x/h250 18.00 A17/M6/17 70 mm² M6x17 mm contained palm cable lug (ea) x/h250 30.00 A19-M8/19 95 mm² M8x19 mm contained palm cable lug (ea) x/h250 41.00 A24B-M8/19 120 mm² M8x19 mm contained palm cable lug (ea) x/h250 52.00 A30B-M8/19 150 mm² M8x19 mm contained palm cable lug (ea) x/h250 78.00 A37-M12/31 185 mm² M12x31 mm contained palm cable lug (ea) h400/630 122.00 A48-M12/31 240 mm² M12x31 mm contained palm cable lug (ea) h400/630 139.00 B-15

Air circuit breakers (ACBs) for MCCBs Hager s ACBs conform to IEC/EN 60947-2 standards and to all major international standards and performance categories. Easy terminal conversion horizontal vertical Many built-in safety features Easy inspection and maintenance facilities Type HWG HWN HWS HWP No. of poles 3/4 Frame 1 2 3 Rated uninterrupted current at 40ºC A 1000,1250 1250, 1600,2000 2000, 2500, 3200 3200, 4000 Rated operational voltage at 50/60Hz Ue V 690 Rated insulation voltage at 50/60Hz Ui V 1000 Rated impulse withstand voltage Uimp kv 12 Utilization category B Compliance EN60947-2, IEC60947-2, GB14048-2 Rated ultimate 400/415V - 50/60Hz Icu KA 50 65 80 100 Short circuit 500/550V - 50/60Hz Icu KA 42 55 70 85 Breaking capacity 660/690V - 50/60Hz Icu KA 42 50 50 75 Rated service short circuit breaking capacity Ics (% Icu) 100% 100% 100% 100% Rated short time 0.5 Sec Icw KA 50 65 80 100 Withstand 1.0 Sec Icw KA 42 65 65 70 Capacity 3.0 Sec Icw KA 25 26 35 50 Rated short 400/415V - 50/60Hz Icw KA 105 143 176 220 Circuit making 500/550V - 50/60Hz Icw KA 88 121 154 187 Capacity 660/690V - 50/60Hz Icw KA 88 105 121 165 Opening time Nt ms 40 40 40 40 Closing time ms 60 60 60 60 Current setting Ir = In x... A 0.4-0.5-0.6-0.7-0.75-0.8-0.85-0.9-0.95-1.0 Overload Time delay Tr at 6 x Ir Sec 0.5-1-2-4-6-8-12-18-24-30 Current setting Is = In x... A 0.6-1.0-1.5-2-3-4-6-8-9-10 Short-circuit Time delay, Ts OFF ms 20-100-200-300-400 Time delay, Ts ON 10xIn-I 2 t ms 20-100-200-300-400 Instantaneous Current setting Ip = In x... A 1.5-2-3-4-5-6-8-10-12-MAX Mechanical life no. of cycles 20 000 20 000 15 000 10 000 Frequency of operation Mechanical cycles/hour 60 Electrical life no. of cycles 10 000 8 000 5 000 5 000 Frequency of operation Electrical cycles/hour 40 40 30 20 Pitch I/C - O/G mm 105 Pitch Ph-Ph mm 100 100 133.3 200 Terminal width mm 80 80 100 165 Dimensions Weight Width 3 pole mm 347 347 447 647 Width 4 pole mm 447 447 581 847 Fixed Depth mm 355 Height mm 430 Width 3 pole mm 347 347 347 647 Width 4 pole mm 447 447 447 847 Drawout Depth mm 418 421 Height mm 433 3 pole kg 39 39 59 86 Fixed 4 pole kg 48 48 71 108 3 pole kg 70 70 88 124 Drawout 4 pole kg 84 84 106 160 B-16

Air circuit breakers (ACBs) Air circuit breakers are supplied standard with the following: fixed draw-out Auxiliary contacts (4NO + 4NC) Panel door ingress seal (flange for compartment door) RTC (ready to close) contact for spring loaded indication Cradle of draw-out circuit breaker Operation (racking) crank handle Safety shutters (padlockable top and bottom) Terminal converters horizontal-vertical connection LSI microprocessor protection and control unit (mechanical trip indication) HWS432A3/RTC Current setting Ir + In x A 0.4-0.5-0.6-0.7-0.8-0.85-0.9-0.95-1 Time delay at 6x Ir s 0.5-1-2-4-6-8-12-18-24-30 Short circuit Is = In x A 0.6-1.0-1.5-2-3-4-6-8-9-10 Time delay Ts 10 x In - I2t ms 20-100-200-300-400 Instantaneous trip Ip = In x A 1.5-2-3-4-5-6-8-12-12-max LED indication for: power ON, overload, short-circuit, instantaneous, percentage load LSIG control unit including earth fault protection available on request breaking capacity frame thermal ka rms 415V adjustment Draw-out air circuit breaker Three pole (supplied with cradle) HWG310A3/RTC 50kA 3 pole air circuit breaker (draw-out) 1 400-1000A 48360.00 HWG312A3/RTC 50kA 3 pole air circuit breaker (draw-out) 1 500-1250A 48360.00 HWN320A3/RTC HWN312A3/RTC 65kA 3 pole air circuit breaker (draw-out) 1 500-1250A 51803.00 HWN316A3/RTC 65kA 3 pole air circuit breaker (draw-out) 1 640-1600A 51803.00 HWN320A3/RTC 65kA 3 pole air circuit breaker (draw-out) 1 800-2000A 67931.00 HWS320A3/RTC 80kA 3 pole air circuit breaker (draw-out) 2 800-2000A 78741.00 HWS325A3/RTC 80kA 3 pole air circuit breaker (draw-out) 2 1000-2500A 78741.00 HWS332A3/RTC 80kA 3 pole air circuit breaker (draw-out) 2 1280-3200A 107857.00 HWP340A3/RTC 100kA 3 pole air circuit breaker (draw-out) 3 1600-4000A 129651.00 Draw-out air circuit breaker Four pole (supplied with cradle) HWN416A3/RTC 65kA 4 pole air circuit breaker (draw-out) 1 640-1600A 68647.00 HWN420A3/RTC 65kA 4 pole air circuit breaker (draw-out) 1 800-2000A 90097.00 HWS425A3/RTC 80kA 4 pole air circuit breaker (draw-out) 2 1000-2500A 104474.00 HWS432A3/RTC 80kA 4 pole air circuit breaker (draw-out) 2 1280-3200A 143199.00 HWP440A3/RTC 100kA 4 pole air circuit breaker (draw-out) 3 1600-4000A 172185.00 Fixed- air circuit breaker Three pole HWS432A3/RTC HWG310C3/RTC 50kA 3 pole air circuit breaker (fixed) 1 400-1000A 35109.00 HWG312C3/RTC 50kA 3 pole air circuit breaker (fixed) 1 500-1250A 35109.00 HWN312C3/RTC 65kA 3 pole air circuit breaker (fixed) 1 500-1250A 37899.00 HWN316C3/RTC 65kA 3 pole air circuit breaker (fixed) 1 640-1600A 37899.00 HWN320C3/RTC 65kA 3 pole air circuit breaker (fixed) 1 800-2000A 52283.00 HWS320C3/RTC 80kA 3 pole air circuit breaker (fixed) 2 800-2000A 59649.00 HWS325C3/RTC 80kA 3 pole air circuit breaker (fixed) 2 1000-2500A 59649.00 HWS332C3/RTC 80kA 3 pole air circuit breaker (fixed) 2 1280-3200A 80571.00 HWP340C3/RTC 100kA 3 pole air circuit breaker (fixed) 3 1600-4000A 96609.00 Fixed- air circuit breaker Four pole HWN416C3/RTC 65kA 4 pole air circuit breaker (fixed) 1 640-1600A 50154.00 HWN420C3/RTC 65kA 4 pole air circuit breaker (fixed) 1 800-2000A 69285.00 HWN320C3/RTC HWS425C3/RTC 80kA 4 pole air circuit breaker (fixed) 2 1000-2500A 79082.00 HWS432C3/RTC 80kA 4 pole air circuit breaker (fixed) 2 1280-3200A 106909.00 HWP440C3/RTC 100kA 4 pole air circuit breaker (fixed) 3 1600-4000A 128238.00 B-17

Air circuit breakers (ACBs) accessories HWX213 voltage Shunt opening release HWX213 240 Vac shunt opening release for all air circuit breakers 1563.00 HWX214 415 Vac shunt opening release for all air circuit breakers 1563.00 HWX215 24 Vdc shunt opening release for all air circuit breakers 1563.00 Shunt closing release HWX253 240 Vac shunt closing release for all air circuit breakers 1563.00 HWX254 415 Vac shunt closing release for all air circuit breakers 1563.00 HWX255 24 Vdc shunt closing release for all air circuit breakers 1563.00 HWX253 Under voltage release HWX233 240 Vac undervoltage release for all air circuit breakers 4298.00 HWX234 415 Vac undervoltage release for all air circuit breakers 4298.00 HWX235 24 Vdc undervoltage release for all air circuit breakers 4298.00 Electric charging device (motor) HWX233 HWX313 240 Vac motor for automatic charging of closing spring 8638.00 HWX314 415 Vac motor for automatic charging of closing spring 8638.00 HWX315 24 Vdc motor for automatic charging of closing spring 8638.00 Protection and control units (LSI supplied standard with ACBs) HWW322 LSI std advanced microprocessor based control and protection unit 10114.00 HWW324 LSIG (as above but with earth fault protection) 10591.00 Mechanical interlocking kits (cable for horizontal or vertical interlocking) Up to three circuit breakers fixed/draw-out/mixed versions can be mechanically interlocked in horizontal or vertical configurations. HWX313 HWY121 mechanical interlock (kit) (for two incommers) 2127.00 HWY122 mechanical interlock (kit) (for three incommers) 3473.00 HWY123 mechanical interlock (kit) (for two incommers and one standby) 3473.00 HWY124 mechanical interlock (kit) (for two incommers and one bus coupler) 3473.00 HWY112 door interlock mechanism for all air circuit breakers 652.00 HWY211 mechanical operation counter for all air circuit breakers 869.00 Accessories HWY121 HWY141 OFF button key lock facility (requires CLKB fortress lock and key) 435.00 HWY131 key locking arrangement (for isolated positions) (requires CLKB fortress lock and key) 435.00 HWY151 key locking arrangement (for all positions) (requires CLKB fortress lock and key) 435.00 HWY114 spare door ingress seal for fixed ACB 652.00 HWY115 spare door ingress seal for draw-out ACB 652.00 CLKB fortress, barrel lock and key for above locking 3750.00 HWY321 Terminals adaptors (convertible from horizontal to vertical) HWY311 terminal adaptor for frame 1 1000-2000A (ea) 667.00 HWY321 terminal adaptor for frame 2 2000-2500A (ea) 903.00 HWY324 terminal adaptor for frame 3 3200A (ea) 1805.00 One adaptor required per ACB terminal two adaptors required per 4000A terminal Neutral current transformer (external) for use with LSIG recharge HWY211 HWW216 1600A external neutral CT for air circuit breakers (frame 1) 5643.00 HWW217 2000A external neutral CT for air circuit breakers (frame 1) 6750.00 HWW227 2500A external neutral CT for air circuit breakers (frame 2) 7379.00 HWW233 3200A external neutral CT for air circuit breakers (frame 3) 11769.00 HWW234 4000A external neutral CT for air circuit breakers (frame 3) 14758.00 B-18

Busbar system / Accessories KM13E KM13N Rail mountable earth/neutral terminals (clips vertically onto rail) KM13N rail mountable neutral terminal (blue) 6x16 + 7x10 mm² 42.00 KM13E rail mountable earth terminal (green) 6x16 + 7x10 mm² 42.00 Terminal support (clips into various distribution boards) KN00A universal terminal support Din rail mount (horizontal or vertical) 105 mm 27.00 Distribution terminals (fully insulated clips onto above support) KN00A Incoming Outgoing 1.5..25 mm² screw clamp terminal 1.5..4 mm² connect cage clamp terminals (push-in) supply output 1.5..25 mm² 1.5..4 mm² KN26E KN10E 63A 2 x 25 mm² 8 x 4 mm² insulated earth terminal (green) 61.00 KN18E 63A 4 x 25 mm² 14 x 4 mm² insulated earth terminal (green) 75.00 KN26E 63A 6 x 25 mm² 20 x 4 mm² insulated earth terminal (green) 91.00 KN99E earth insulated bridge piece for above terminals (push-in) 133.00 KN10N 63A 2 x 25 mm² 8 x 4 mm² insulated neutral terminal (blue) 61.00 KN18N 63A 4 x 25 mm² 14 x 4 mm² insulated neutral terminal (blue) 75.00 KN26N 63A 6 x 25 mm² 20 x 4 mm² insulated neutral terminal (blue) 91.00 KN99... KN99N neutral insulated bridge piece for above terminals (10pcs) 133.00 KN10P 63A 2 x 25 mm² 8 x 4 mm² insualted phase terminal (brown) 61.00 KN18P 63A 4 x 25 mm² 14 x 4 mm² insualted phase terminal (brown) 75.00 KN26P 63A 6 x 25 mm² 20 x 4 mm² insualted phase terminal (brown) 91.00 KN99P phase insulated bridge piece for above terminals (10 pcs) 133.00 KN04P KN04N 90A 4 x 25 mm² screw clamp insulated neutral termina (blue) 38.00 KN07N 90A 7 x 25 mm² screw clamp insulated neutral termina (blue) 40.00 KN04P 90A 4 x 25 mm² screw clamp insulated phase terminal (brown) 38.00 KN07P 90A 7 x 25 mm² screw clamp insulated phase terminal (brown) 40.00 KN07N Single-pole distribution blocks (fully protected) Icc: 36kA Space saving IP20 protection DIN rail or bolt down mounting One main cable input - various cable outputs KJ02C amps incoming outgoing terminals (per phase) mm² Icc terminals 1.5...6 2.5...10 2.5...16 2.5...25 6...35 ka poles KJ02D 125A 1x35/1x16 mm² 6 36 1 pole 307.00 KJ02C 160A 70 mm² 6 36 1 pole 492.00 KJ02A 250A 95 mm² 4 5 2 36 1 pole 634.00 KJ02B 400A 150 mm² 4 5 2 36 1 pole 687.00 Multi-pole distribution blocks (3Ph+N distribution bars in modular format) KJ02A KJ01B Modular DIN rail mounting (mounts through modular front cut-out) High fault level IEC 60947-1 incoming outgoing terminals (per phase) mm² Icc amps poles terminals 1.5...6 2.5...10 2.5...16 2.5...25 6...35 ka KJ01A 100A 35 mm² 10 1 29 2 pole 443.00 KJ01B 80A 16 mm² 8 21 4 pole 443.00 KJ01C 125A 35 mm² 10 1 29 4 pole 502.00 KJ01D 160A 50 mm² 8 3 20 4 pole 1530.00 B-19 KJ02E KJ02E 100A 25 mm² 5/4 2/6 20 4 pole 475.00 = neutral terminals

DIN modular domestic sockets / Safety lockout hasps 6540091 Permits the mounting of domestic switches and/or sockets into standard DIN distribution boards with same dimensions and cutout as modular MCB s to provide an electrical connection for tools or recording instruments. DIN rail mounting housing/support for domestic switches and sockets Mounts into standard distribution boards with same dimensions and cutout as MCB s Two modular widths: one module (18 mm) and two module (36 mm) DIN rail support for Evolution series no. modules (W) 18 mm 654.0091 DIN rail support for Evolution series switches or sockets (1 module) 19.00 654.0092 DIN rail support for Evolution series switches or sockets (2 module) 16.00 Evolution series switches and sockets for above supports Simply clips into DIN rail mount housing (above) 6540092 + 1016414G 101.6414.G 15A 2P+E South African socket for housings (2 module) 107.00 101.6403.G 16A 2P+E Italian socket for housings (1 module) 40.00 101.6303.G 16A 1 Pole switch for housings (I-O) (1 module) 39.00 101.6311.G 16A 2 Pole changeover switch for housings (I-O-II) (1 module) 70.00 Safety lockout hasps Safety lockout hasps permit multiple padlocks to be used when isolating one energy source. The lockout hasp is placed through the isolating point and closed. Each person carrying out maintenance or service attaches their unique individually keyed padlock through the lockout hasp, thereby ensuring complete safety during maintenance operations. The hasp can only be removed once all padlocks have been removed. Scissor action hasp with Ø 25 mm or 38 mm jaw size Accepts padlocks with a shackle diameter up to 9 mm (up to 6 padlocks can be attached) Manufactured from high tensile steel, electroplated to prevent rust ES-VCH-S number of jaw size colour padlocks accepted Vinyl coated hasp Padlock section vinyl coated (red) for improved grip and visibility ES-VCH-S 25 mm red 6 saftey lockout hasp 110.00 ES-VCH-P 38 mm red 6 saftey lockout hasp 127.00 ES-VCH-P Lockout padlocks Maximum security laminated padlocks made for tough lockout situations. Increased durability against cutting, prying and twisting Supplied with two keys per lock ES-PLS-KD padlock long shackle - different keys 320.00 ES-PLS-KD B-20

Earth leakage protection new RESYS M40 earth leakage relays associated with a remote trip breaking device (automatic power breaking), provide the following functions: Protection against indirect contact Limitation of leakage currents They also preventively monitor electrical installations via a (configurable) pre-alarm function or when used as a signalling relay. 4941 3723 Modular DIN rail mountable (same format as MCB s) 44mm wide 2 relays with configurable function (alarm or pre-alarm at 50% IΔn) Adjustment of IΔn: 0.03-0.1-0.3-0.5-1 - 3-5 - 10-30A Time delay: 0-0.06-0.15-0.30-0.50-0.80-1 - 4-10 sec Positive or negative security Tripping accuracy by TRMS measurement (improves immunity to nuisance tripping) LED bargraph provides real-time display of leakage currents current time power setting delay supply IΔn (sec) RESYS M40 A differential relay 4941 3723 0.03 ~ 30A 0 ~ 10 115/230 Vac electronic earth leakage relay 2326.00 4941 3740 0.03 ~ 30A 0 ~ 10 400 Vac electronic earth leakage relay 2326.00 4941 3602 0.03 ~ 30A 0 ~ 10 12~125 Vdc electronic earth leakage relay 2482.00 RESYS M40R with automatic reclosing 4941 3724 M40R relay recloses the system up to six consecutive times after preselected time intervals. If the fault is still present after the sequence of six reclosing attempts, the relay is locked in alarm mode and a manual intervention will be required. Time delay between two reclosings: 7.7-15 - 30-60 - 120-240 sec 4941 3724 0.03 ~ 30A 0 ~ 10 115/230 Vac reclosing earth leakage relay 2326.00 4941 3741 0.03 ~ 30A 0 ~ 10 400 Vac reclosing earth leakage relay 2326.00 new RESYS P40 panel mounting (48x48mm) As per RESYS M40 (above) but in panel mounting version 4942 3723 0.03 ~ 30A 0 ~ 10 115/230 Vac panel mount earth leakage relay 3050.00 Core balance transformers (torroidal transformers) - A Active conductors pass through the aperture of the core balance transformer, providing a differential summation of vector currents, enabling detection of leakage currents. 4941 3723 aperture dimensions (mm) Ø diameter (H) (W) (D) 4950 6030 30 mm core balance transformer for e/leakages 104 92 26 1038.00 4950 6050 50 mm core balance transformer for e/leakages 125 103 26 1299.00 4950 6080 80 mm core balance transformer for e/leakages 143 116 26 1456.00 4950 6120 120 mm core balance transformer for e/leakages 183 163 26 2019.00 4950 6200 200 mm core balance transformer for e/leakages 274 253 51 4558.00 Larger aperture sizes available on request Accessories for above 4950 0011 30 mm for directly mounting transformers onto cables 263.00 4950 0012 50 mm for directly mounting transformers onto cables 426.00 4950 0013 80 mm for directly mounting transformers onto cables 887.00 4950 0014 120 mm for directly mounting transformers onto cables 1007.00 4950 0031 DIN-rail clip (for directly mounting core balance transformer onto DIN rail) 90.00 4950 6080 B-21

Load break switches 16A - 160A 2200 3005 2200 3011 SIRCO M and MV manually operated switches SIRCO modular multipole switches make and break under load conditions and provide safety isolation for any low voltage circuit, particularly for machine control circuits. Modular DIN rail mounting (fits into standard distribution board 45mm cutout) External front (or side) operating handle and shaft (to be ordered seperately-see below) Severe load duty categories (AC-22 and AC-23) Conformity to standards: IEC/EN 60947-3 / IS13947-3 / UL / KEMA / RINA AC-22 A AC-23 A No. dimensions (mm) 415V (A) 400V (kw) poles (H) (W) (D) SIRCO M series load break switches 16-125A 2200 3000 16A 7.5kW 3 load break switch 68 45 75 190.00 2200 3002 25A 11.0kW 3 load break switch 68 45 75 217.00 2200 3003 32A 15.0kW 3 load break switch 68 45 75 245.00 2200 3004 40A 18.5kW 3 load break switch 68 45 75 250.00 2200 3005 63A 22.0kW 3 load break switch 68 45 75 337.00 2200 3009 100A 37.0kW 3 load break switch 76 53 75 601.00 2200 3011 125A 55.0kW 3 load break switch 125 78 75 768.00 SIRCO MV series load break switches 160A Visual double break contacts 2200 3016 160A 75.0kW 3 load break switch 125 109 75 1570.00 2200 4016 160A 75.0kW 4 load break switch 125 135 75 1895.00 2200 3016 Operating handles and shafts for above switches (IP65) External front operated, door interlocking, padlockable in off position (3 padlocks) 2299 0001 1474 1111 2200 1005 1473 1111 1413 2111 1407 0520 2299 0011 2200 1011 2209 6009 handle colour for switch 1473 1111 S00 black operating handle (external) M 16-100A 119.00 1474 1111 S00 red/yellow operating handle (external) M 16-100A 119.00 1483 1111 S0 black operating handle (external) M 125A 171.00 1493 0111 S0 black operating handle (external) MV 160A 196.00 1413 2111 S1 black operating handle (external) MV 160A 282.00 141D 2911 S1 black as above (with metal connection) MV 160A 439.00 Defeatable interlocking mechanism Extension shafts for switches 1407 0520 S000/00 200 5 extension shaft M 16~125A 49.00 1407 0532 S000/00 320 5 extension shaft M 16~125A 65.00 1409 0632 S0 320 6 extension shaft MV 160A 82.00 1401 0632 S1 320 6 extension shaft MV 160A 270.00 1429 0000 shaft guide (permits engaging of misaligned shaft with handle) (all sizes) 93.00 Direct mount handles (mounts directly onto front of switch) 2299 5012 M00 blue 5 direct mount handle M 16~80A 17.00 2299 5032 M01 blue 5 direct mount handle M 100~125A 49.00 2299 5042 M0b blue 6 direct mount handle MV 160A 65.00 Auxiliary contacts for switches 2299 0001 1NO+1NC side mount auxiliary contact 16~160A 168.00 2299 0011 2NO side mount auxiliary contact 16~160A 168.00 3999 0701 1NO internal mounting auxiliary contact 160A 136.00 3999 0702 1NC internal mounting auxiliary contact 160A 136.00 Attachable 4th pole module (clips onto side of switch) 2200 1003 32A 1 pole attachable 4th pole module 16-32A 92.00 2200 1005 63A 1 pole attachable 4th pole module 16-63A 120.00 2200 1009 100A 1 pole attachable 4th pole module 100A 238.00 2200 1011 125A 1 pole attachable 4th pole module 125A 263.00 Conversion kits (mechanical interlock / parallel attachment) supplied with internal direct mount handle 2209 6009 I-O-II changeover mechanism between two switches 16~100A 380.00 2209 6011 I-O-II changeover mechanism between two switches 125A 654.00 1473 1113 I-O-II handle for above changeover switches 16~125A 158.00 2269 6009 I-O 6/8 pole conversion kit between two switches 16~100A 380.00 2269 6011 I-O 6/8 pole conversion kit between two switches 125A 654.00 Door mount kit (for direct door or side panel mounting of Sirco M switches) 2299 3409 door mounting kit (direct door mounting of switch) 16~100A 98.00 B-22

Load break switches 125A - 3200A SIRCO manually operated switches SIRCO switches make and break under load conditions and provide safety isolation for any low voltage circuit, particularly for machine control circuits. External front operating handle and shaft (to be ordered separately - see below) Severe load duty categories (AC-22 and AC-23) Conformity to standards: IEC/EN 60947-3 / IS13947-3 / UL / KEMA / RINA AC-22 A AC-23 A No. dimensions (mm) 415V (A) 400V (kw) poles (H) (W) (D) 26AC 3025 SIRCO AC series load break switches 125-5000A SIRCO s double break per pole achieved through its sliding bar contact system offers very high durability and short-circuit withstand. Specifically designed arcing chambers provide the switch with improved breaking performance. Position indicator located on the sliding bar mechanism, ensures visibility in all circumstances. High thermal and dynamic withstand High electrical and mechanical endurance 2600 3014 125A 63kW 3 load break switch 135 140 115 726.00 2600 3017 160A 80kW 3 load break switch 135 140 115 840.00 26AC 3020 200A 100kW 3 load break switch 160 180 115 1807.00 26AC 3025 250A 132kW 3 load break switch 160 180 115 1892.00 26AC 3031 315A 160kW 3 load break switch 160 180 115 2237.00 26AC 3040 400A 220kW 3 load break switch 235 230 166 3416.00 26AC 3063 630A 280kW 3 load break switch 280 280 166 4672.00 26AC 3080 800A 450kW 3 load break switch 280 280 166 5972.00 26AC 3100 1000A 560kW 3 load break switch 280 280 166 10113.00 26AC 3121 1250A 710kW 3 load break switch 372 372 166 12323.00 26AC 3160 1600A 710kW 3 load break switch 372 372 166 17014.00 26AC 3200 2000A 710kW 3 load break switch 380 372 226 27548.00 2600 3250 2500A 710kW 3 load break switch 380 372 226 29223.00 2600 3320 3200A 710kW 3 load break switch 380 372 226 36901.00 4 pole switches 26AC 4025 250A 132kW 4 load break switch 160 230 115 2578.00 26AC 4040 400A 220kW 4 load break switch 235 290 166 4385.00 26AC 4063 630A 280kW 4 load break switch 280 360 166 5931.00 26AC 4080 800A 450kW 4 load break switch 280 360 166 8786.00 26AC 4121 1250A 710kW 4 load break switch 372 492 166 17215.00 Larger sizes (up to 5000A) available on request - 4 pole available on request Operating handles and shafts for above switches (IP65) External front operated, door interlocking, padlockable in off position (3 padlocks) 1423 2111 handle colour for switch Pistol grip handles for SIRCO (IP65) 1423 2111 S2 black operating handle (external) 125-400A 308.00 142D 2911 S2 black as above (with metal connection) 125-400A 450.00 T grip handles for SIRCO (IP65) 1443 3111 S4 black operating handle (external) 630-1600A 807.00 144D 3911 S4 black as above (with metal connection) 630-1600A 969.00 1453 8111 S5 black operating handle (external) 2000-3200A 2156.00 Extension shafts for switches handle length mm for switch 1400 1020 1400 1020 S2 200mm 10 extension shaft 125~400A 114.00 1400 1032 S2 320mm 10 extension shaft 125~400A 126.00 1400 1050 S2 500mm 10 extension shaft 125~400A 321.00 1401 1520 S4 200mm 15 extension shaft 630~1600A 249.00 1401 1532 S4 320mm 15 extension shaft 630~1600A 267.00 1401 1540 S4 400mm 15 extension shaft 630~1600A 500.00 2799 3018 S5 320mm 30 extension shaft 2000~3200A 385.00 1429 0000 shaft guide (permits engaging of misaligned shaft with handle) (all sizes) 93.00 2699 0031 Direct mount handles (mounts directly onto front of switch) 1113 1111 J1 black 10 direct mount handle 200~400A 346.00 2799 7012 C2 black 15 direct mount handle 630~1600A 758.00 2799 7042 S5 black 30 direct mount handle 2000~3200A 1182.00 Auxiliary contacts for switches 2699 0031 1 Ch/Over auxiliary contact and support 125~3200A 223.00 2699 0032 1 Ch/Over additional auxiliary contact 125~3200A 298.00 See terminal shrouds and screens overleaf page B-33 B-23

Motorised switch / Enclosed isolators 1915 3063 ESW3080M Ideal contactor replacement for high current switching applications Reliable, robust AC-23A switching Manual override facility (handle supplied) AC-22A AC-23A dimensions (mm) 400V 400V (H) (W) (D) Motorised load-break switches 1915 3016 160A 75kW 3 pole motorised load break switch 135 221 173 14242.00 1915 3025 250A 132kW 3 pole motorised load break switch 160 262 173 16563.00 1915 3040 400A 220kW 3 pole motorised load break switch 170 262 173 22787.00 1915 3063 630A 280kW 3 pole motorised load break switch 260 319 250 27217.00 1915 3080 800A 450kW 3 pole motorised load break switch 321 386 327 41932.00 1915 3100 1000A 560kW 3 pole motorised load break switch 321 386 327 43619.00 1915 3120 1250A 710kW 3 pole motorised load break switch 330 386 327 47629.00 1915 3160 1600A 710kW 3 pole motorised load break switch 288 475 327 64560.00 1915 4063 630A 280kW 4 pole motorised load break switch 260 379 250 31278.00 1915 4080 800A 450kW 4 pole motorised load break switch 321 466 327 45519.00 1915 4100 1000A 560kW 4 pole motorised load break switch 321 466 327 48367.00 1915 4120 1250A 710kW 4 pole motorised load break switch 288 466 327 56912.00 1915 4160 1600A 710kW 4 pole motorised load break switch 288 598 327 73948.00 Enclosed isolator switches (manually operated) Sheet metal enclosure (IP65) IP65 sheet metal enclosed 3 pole load-break switches Door interlocking external handle (in ON position) Padlockable handle in OFF position (up to 3 padlocks) Colour: BS/EN06 E53 (electric orange) ESW3004M 40A 18.5kW 3 pole enclosed load break switch 350 250 170 1411.00 ESW3006M 63A 30kW 3 pole enclosed load break switch 350 250 170 1498.00 ESW3012M 125A 63kW 3 pole enclosed load break switch 350 250 170 2219.00 4 pole can be made up by attaching additional 4th pole (see page B-22) to above switches ESW3016M 160A 80kW 3 pole enclosed load break switch 350 250 170 2359.00 ESW3025M 250A 132kW 3 pole enclosed load break switch 550 400 220 4065.00 ESW3040M 400A 220kW 3 pole enclosed load break switch 550 400 220 5425.00 ESW3063M 630A 280kW 3 pole enclosed load break switch 550 400 220 7451.00 ESW3080M 800A 450kW 3 pole enclosed load break switch 950 700 270 10170.00 ESW3100M 1000A 560kW 3 pole enclosed load break switch 950 700 270 13394.00 ESW3125M 1250A 710kW 3 pole enclosed load break switch 950 700 270 16574.00 ESW4017M 160A 80kW 4 pole enclosed load break switch 350 250 170 3284.00 ESW4026M 250A 132kW 4 pole enclosed load break switch 550 400 220 4734.00 ESW4041M 400A 220kW 4 pole enclosed load break switch 550 400 220 6711.00 ESW4064M 630A 280kW 4 pole enclosed load break switch 550 400 220 9395.00 ESW4080M 800A 450kW 4 pole enclosed load break switch 950 700 270 13763.00 ESW4125M 1250A 710kW 4 pole enclosed load break switch 950 700 270 22336.00 Larger sizes available on request Safety enclosures (IP55) Safety enclosed switches provide emergency stop and safety breaking for any low voltage electric circuit. They break ON and OFF load and provide safety isolation. Zinc galvanised sheet metal enclosure 1.5mm thick, door mounted on chrome plated zamak hinges Polyester powder coated corrosion protection minimum thickness 70μm. Bottom mounted gland plate and 2 internal + 1 external earthing connection Metallic side mounted operating handle (red colour) padlockable in OFF position (3 padlocks) Equipped with a double locking system (door can also be padlocked closed in the OFF position) Visible breaking facility is provided through a triplex window (made of 2 layers 3mm thick safety glass) Mechanical flag indicator (visible through triplex window) for indication of switch position status 2 sets terminated auxiliary contacts NO + NC mounted on the double locking system internally Supplied with 2 hooded pushbuttons on right side of enclosure: green 1 NO / red 2 NC contacts Shrouded upper terminals preventing inadvertent touching of incoming supply terminals Colour: BS/EN06 E53 (electric orange) AC-23A AC-23A dimensions (mm) 400V 525V (H) (W) (D) 25484 15kW 25kW 80A Sider 3P 1way safety switch 400 300 160 14675.00 43505 25kW 55kW 125A Sider 3P 1way safety switch 400 300 200 25597.00 43506 63kW 90kW 200A Sider 3P 1way safety switch 400 300 200 30007.00 43565 157kW 160kW 400A Sider 3P 1way safety switch 700 400 250 33804.00 43566 250kW 270kW 630A Sider 3P 1way safety switch 900 500 300 63951.00 B-24

Changeover switches 16A - 3200A SIRCO M and SIRCOVER manual changeover switches SIRCO manual multipolar changeover switches provide switching, source inversion and changeover under load for two power circuits, as well as their safety isolation by double breaking per pole. Severe load duty categories (AC-23 and AC-33) Conformity to standards: IEC/EN 60947-3, IEC 60947-6-1, IS13947-3, UL, KEMA, RINA External front (or side) operating handle and shaft (to be ordered separately - see below) 1433 3113 2230 3005 41AC 3063 AC-23 A No. dimensions (mm) 415V (A) poles (H) (W) (D) SIRCO M changeover switches 16-125A Modular DIN rail mounting (fits into standard distribution board 45mm cutout) Supplied with internal direct mount handle 2230 3002 25A 3 pole modular changeover switch 68 98 95 880.00 2230 3004 40A 3 pole modular changeover switch 68 98 95 945.00 2230 3005 63A 3 pole modular changeover switch 68 98 95 1410.00 2230 3009 100A 3 pole modular changeover switch 76 105 95 1648.00 2230 3011 125A 3 pole modular changeover switch 125 159 100 2255.00 4 pole available by adding 4th poles (see page B-22) Operating handles and shafts for above changeover switches (IP65) 1473 1113 S00 black I-O-II ext. operating handle 25-100A 158.00 1403 2113 S01 black I-O-II ext. operating handle 125A 416.00 1407 0532 320mm extension shaft for switch 25-100A 65.00 1409 0632 320mm extension shaft for switch 125A 82.00 SIRCOVER changeover switches 160-3200A Position indicator located on the sliding bar mechanism, ensures visibility in all circumstances High thermal and dynamic withstand High electrical and mechanical endurance Severe utilization categories (AC-22 and AC-23) 41AC 3016 160A 3 pole manual changeover switch 135 221 173 4440.00 41AC 3020 200A 3 pole manual changeover switch 135 221 173 5188.00 41AC 3025 250A 3 pole manual changeover switch 160 262 173 6151.00 41AC 3039 400A 3 pole manual changeover switch 170 262 173 9946.00 41AC 3063 630A 3 pole manual changeover switch 260 319 225 11021.00 41AC 3080 800A 3 pole manual changeover switch 321 386 298 19357.00 41AC 3100 1000A 3 pole manual changeover switch 321 386 298 22789.00 41AC 3120 1250A 3 pole manual changeover switch 330 386 298 25050.00 41AC 3160 1600A 3 pole manual changeover switch 228 478 298 45211.00 41AC 4016 160A 4 pole manual changeover switch 135 251 173 5995.00 41AC 4020 200A 4 pole manual changeover switch 135 251 173 7002.00 41AC 4025 250A 4 pole manual changeover switch 160 312 173 8651.00 41AC 4039 400A 4 pole manual changeover switch 170 312 173 14662.00 41AC 4063 630A 4 pole manual changeover switch 260 379 225 15001.00 41AC 4080 800A 4 pole manual changeover switch 320 466 298 27896.00 41AC 4120 1250A 4 pole manual changeover switch 330 466 298 34017.00 41AC 4160 1600A 4 pole manual changeover switch 288 598 298 63474.00 External handle (door interlocking padlockable in O position) 1423 2113 S2 black I-O-II ext. operating handle 125-630A 590.00 1443 3113 S4 black I-O-II ext. operating handle 800-1600A 1504.00 1400 1032 320mm extension shaft for switch 125-630A 126.00 1401 1532 320mm extension shaft for switch 800-1600A 267.00 1122 1111 J2 black direct switch mounting handle 125-630A 239.00 2799 7052 C1 black direct switch mounting handle 800-1600A 758.00 Bridging bars for changeover switches 125-1600A 4109 3019 3 pole bridging bar set for switch 160-200A 741.00 4109 3025 3 pole bridging bar set for switch 250A 953.00 4109 3039 3 pole bridging bar set for switch 400A 1182.00 4109 3063 3 pole bridging bar set for switch 630A 1821.00 4109 3080 3 pole bridging bar set for switch 800-1000A 2753.00 4109 3120 3 pole bridging bar set for switch 1250A 4199.00 4109 3160 3 pole bridging bar set for switch 1600A 6346.00 4109 4019 4 pole bridging bar set for switch 160-200A 1031.00 4109 4025 4 pole bridging bar set for switch 250A 1268.00 4109 4039 4 pole bridging bar set for switch 400A 1481.00 4109 4063 4 pole bridging bar set for switch 630A 2425.00 4109 4080 4 pole bridging bar set for switch 800-1000A 3887.00 4109 4120 4 pole bridging bar set for switch 1250A 5596.00 4109 4160 4 pole bridging bar set for switch 1600A 8462.00 B-25

Bypass switches 160A - 1600A / Enclosed manual changeover switch 2799 3018 4100 7063 EC03009P EC03009M SIRCOVER manual Bypass switches 160A - 1600A SIRCOVER Bypass are a combination of three interlocked switches enabling the use with 3+6 or 4+8 poles from 160A to 1600A. Severe load duty categories (AC-23 and AC-33) Conformity to standards: IEC/EN 60947-3, IEC 60947-6-1, IS13947-3, UL, KEMA, RINA External front operating handle and shaft (to be ordered separately - see below) SIRCOVER bypass switches AC-23 A No. dimensions (mm) 415V (A) poles (H) (W) (D) 125-3200A 4100 7016 160A 3 pole manual bypass switch 135 221 268 8926.00 4100 7019 200A 3 pole manual bypass switch 135 221 268 11902.00 4100 7025 250A 3 pole manual bypass switch 160 262 268 13761.00 4100 7039 400A 3 pole manual bypass switch 170 262 268 19295.00 4100 7063 630A 3 pole manual bypass switch 260 319 387 27871.00 4100 7080 800A 3 pole manual bypass switch 320 386 508 35560.00 4100 7120 1250A 3 pole manual bypass switch 320 386 508 57605.00 4100 7160 1600A 3 pole manual bypass switch 288 478 508 77596.00 4100 9016 160A 4 pole manual bypass switch 135 251 268 10577.00 4100 9019 200A 4 pole manual bypass switch 135 251 268 13455.00 4100 9025 250A 4 pole manual bypass switch 160 312 268 14485.00 4100 9039 400A 4 pole manual bypass switch 170 312 268 20311.00 4100 9063 630A 4 pole manual bypass switch 260 379 387 36125.00 4100 9080 800A 4 pole manual bypass switch 320 466 508 46730.00 4100 9120 1250A 4 pole manual bypass switch 320 466 508 76227.00 4100 9160 1600A 4 pole manual bypass switch 288 598 508 88232.00 External handle (IP65) (door interlocking padlockable in O position) 1423 2113 S2 black I-O-II ext. operating handle 160-200A 590.00 1443 3113 S4 black I-O-II ext. operating handle 250-630A 1504.00 4199 7146 black I-O-II ext. operating handle 800-1600A 3810.00 1400 1032 320mm extension shaft for switch 160-200A 126.00 1401 1532 320mm extension shaft for switch 250-630A 267.00 2799 3018 320mm extension shaft for switch 800-1600A 385.00 4199 5012 B3 black direct switch mounting handle 160-200A 396.00 2799 7052 C1 black direct switch mounting handle 250-630A 758.00 2799 7012 C2 black direct switch mounting handle 800-1600A 758.00 Enclosed manual changeover switches (IP65) Polycarbonate housing (IP65) distribution board enclosure Supplied with internal direct mount handle EC03002P 25A 3 pole enclosed changeover switch 210 237 114 1372.00 EC03004P 40A 3 pole enclosed changeover switch 210 237 114 1437.00 EC03006P 63A 3 pole enclosed changeover switch 210 237 114 1902.00 EC03009P 100A 3 pole enclosed changeover switch 210 237 114 2140.00 EC03012P 125A 3 pole enclosed changeover switch 210 237 114 2747.00 Sheet metal enclosed (IP65) Supplied with external door interlocking handle padlockable in O position EC03004M 40A 3 pole enclosed changeover switch 350 250 170 3258.00 EC03006M 63A 3 pole enclosed changeover switch 350 250 170 4188.00 EC03009M 100A 3 pole enclosed changeover switch 350 250 170 4664.00 EC03012M 125A 3 pole enclosed changeover switch 350 250 170 5993.00 4 pole switches are made with add-on 4th poles (see page B-22) EC3013M 125A 3 pole enclosed changeover switch 550 400 220 6850.00 EC3016M 160A 3 pole enclosed changeover switch 550 400 220 7480.00 EC3025M 250A 3 pole enclosed changeover switch 550 400 220 9420.00 EC3040M 400A 3 pole enclosed changeover switch 850 600 270 14950.00 EC3063M 630A 3 pole enclosed changeover switch 850 600 270 16670.00 EC3080M 800A 3 pole enclosed changeover switch 900 600 450 29580.00 EC3125M 1250A 3 pole enclosed changeover switch 900 600 450 34980.00 EC3160M 1600A 3 pole enclosed changeover switch 900 600 450 59150.00 EC4016M 160A 4 pole enclosed changeover switch 550 400 220 9640.00 EC4025M 250A 4 pole enclosed changeover switch 550 400 220 12340.00 EC4040M 400A 4 pole enclosed changeover switch 850 600 270 20060.00 EC4063M 630A 4 pole enclosed changeover switch 850 600 270 21260.00 EC4080M 800A 4 pole enclosed changeover switch 900 600 450 39050.00 EC4125M 1250A 4 pole enclosed changeover switch 900 600 450 46480.00 EC4160M 1600A 4 pole enclosed changeover switch 900 600 450 78810.00 B-26

Motorised changeover switches 40A - 160A new ATyS S motorised 4 pole changeover switches Fully integrated cost effective solution to switch between main and an alternative power supply for loads of up tp 125A: <90kVA /3 phase 415Vac. Manual override facility (handle supplied) Fail-safe mechanical interlock Wide-band AC control voltage ± 30% Padlockable in the OFF position Can be configured for impulse or contactor logic Energy efficient power consumption is minimal and only required during transfer Fully independent position auxiliary contacts one for each position ( I / O / II ) AC 32B IEC 60947-6-1, GB 14048-11 (transfer switch standards) AC 22A IEC60947-3 (load break switch standard) 9503 4008 AC-31 B 415V (A) poles supply voltage 9509 4012 9594 4012 9599 4001 1323 2010 1323 4012 ATyS S motorised changeover switches (H) 144 x (W) 198 x (D) 181 mm 230 Vac power supply 9503 4004 40A 4 pole 230 Vac motorised changeover switch 4032.00 9503 4006 63A 4 pole 230 Vac motorised changeover switch 4430.00 9503 4008 80A 4 pole 230 Vac motorised changeover switch 5437.00 9503 4010 100A 4 pole 230 Vac motorised changeover switch 6041.00 9503 4012 125A 4 pole 230 Vac motorised changeover switch 6846.00 12 Vdc power supply 9505 4004 40A 4 pole 12 Vdc motorised changeover switch 4032.00 9505 4006 63A 4 pole 12 Vdc motorised changeover switch 4430.00 9505 4008 80A 4 pole 12 Vdc motorised changeover switch 5437.00 9505 4010 100A 4 pole 12 Vdc motorised changeover switch 6041.00 9505 4012 125A 4 pole 12 Vdc motorised changeover switch 6846.00 24/48 Vdc power supply 9506 4004 40A 4 pole 24/48 Vdc motorised changeover switch 4032.00 9506 4006 63A 4 pole 24/48 Vdc motorised changeover switch 4430.00 9506 4008 80A 4 pole 24/48 Vdc motorised changeover switch 5437.00 9506 4010 100A 4 pole 24/48 Vdc motorised changeover switch 6041.00 9506 4012 125A 4 pole 24/48 Vdc motorised changeover switch 6846.00 ATyS Sd incorporates a dual control power supply 2 x 230 Vac dual power supply 9513 4004 40A 4 pole 2x230 Vac motorised changeover switch 5376.00 9513 4006 63A 4 pole 2x230 Vac motorised changeover switch 5931.00 9513 4008 80A 4 pole 2x230 Vac motorised changeover switch 6864.00 9513 4010 100A 4 pole 2x230 Vac motorised changeover switch 7551.00 9513 4012 125A 4 pole 2x230 Vac motorised changeover switch 8347.00 Accessories 9509 4012 4 pole power terminal bridging bar set (top or bottom) 374.00 9599 4001 control voltage tapping kit (from power terminals) 237.00 9594 4012 top supply side terminal protection shrouds x 2 237.00 9594 9012 bottom load side terminal protection shrouds x 2 237.00 9503 5012 230 Vac spare motor for above switches 4531.00 9513 5012 2x230 Vac spare motor for above switches 5949.00 9505 5012 12 Vdc spare motor for above switches 4531.00 9506 5012 24/48 Vdc spare motor for above switches 4531.00 ATyS M 3s motorised changeover switches (H) 245 x (W) 2P 235/4P 340 x (D) 74 mm ATyS M single-phase or three-phase modular motorised changeover switches with positive break indication,enable on load changeover switching of two supply sources in automatic or manual mode. Modular format to easily mount into standard distribution boards Provide rapid switching, excellent dynamic withstand and long life Positive break indication, switch position indication with back-up manual operation Auto or manual operation (with incorporated Allen key) padlockable in O position 1323 2006 63A 2 pole 230 Vac motorised changeover switch 7703.00 1323 2008 80A 2 pole 230 Vac motorised changeover switch 8176.00 1323 2010 100A 2 pole 230 Vac motorised changeover switch 8770.00 1323 2012 125A 2 pole 230 Vac motorised changeover switch 9243.00 1323 4006 63A 4 pole 230 Vac motorised changeover switch 9062.00 1323 4008 80A 4 pole 230 Vac motorised changeover switch 9619.00 1323 4010 100A 4 pole 230 Vac motorised changeover switch 10317.00 1323 4012 125A 4 pole 230 Vac motorised changeover switch 10874.00 1323 4016 160A 4 pole 230 Vac motorised changeover switch 13244.00 B-27

Motorised changeover switches 63A - 160A ATyS M 6s automatic changeover switches The ATyS M 6s switch monitors the supply from mains and from generator, if mains fails, the switch provides an output for generator start and once the generator voltage reaches the correct level, switches over to the generator supply until mains is restored which causes the switch to change to the mains supply providing a generator stop signal. AC-31 B 415V (A) poles ATyS M 6s automatic changeover switches supply voltage Monitoring parameters configured via dip switches and potentiometers Potentiometers for: (H) 245 x (W) 2P 235/4P 340 x (D) 47 mm nominal voltage configuration voltage and frequency threshold configuration operating cycle configuration 1354 4016 DIP- switches for: LED indication of: 50 or 60Hz, single or 3-phase delay in O position during I-O transfer cycles network/network or network/genset application supply source availability, automatic mode, fault External command inputs for: 2 pole switches automatic mode inhibition remote test on-load (or priority change) manual change of supply from emergency to main source 1NO output relay fro generator start/stop command 1NO fault relay 1353 2004 40A 2 pole 230 Vac automatic changeover switch 11552.00 1353 2006 63A 2 pole 230 Vac automatic changeover switch 12095.00 1353 2008 80A 2 pole 230 Vac automatic changeover switch 12554.00 1353 2010 100A 2 pole 230 Vac automatic changeover switch 13152.00 4 pole switches 1354 4006 63A 4 pole 230 Vac automatic changeover switch 14229.00 1354 4008 80A 4 pole 230 Vac automatic changeover switch 14769.00 1354 4010 100A 4 pole 230 Vac automatic changeover switch 15472.00 1354 4012 125A 4 pole 230 Vac automatic changeover switch 16072.00 1354 4016 160A 4 pole 231 Vac automatic changeover switch 18448.00 ATyS M 6e automatic transfer switches (digital display and settings) 1309 4006 1364 4012 Self powered from incoming supply, the digital inbuilt control unit monitors voltage and frequency thresholds and can be programmed to automatically switch form one supply source to another. Monitoring parameters configured via pushbuttons and digital display Network/genset, network/network (with or without priority) Display/keyboard for programming values and visualisation of electrical parameters LED indicator: power on, supply status, position of switch, auto/manual/test mode, fault 3 configurable inputs 3 configurable output relays 1 configurable bi-stable output relay for generator start/stop command 4 pole switches 1364 4006 63A 4 pole 230 Vac automatic changeover switch 21964.00 1364 4008 80A 4 pole 230 Vac automatic changeover switch 24615.00 1364 4010 100A 4 pole 230 Vac automatic changeover switch 25967.00 1364 4012 125A 4 pole 230 Vac automatic changeover switch 27969.00 1364 4016 160A 4 pole 230 Vac automatic changeover switch 33487.00 Accessories for all ATyS M switches Bridging bars (plug-in) (for incoming of outgoing side of switch) Provides a common connection between switches I & II on the incoming or outgoing side of the ATyS M without reducing terminal capacity. 1309 0001 1399 4006 1309 2006 63-125A 2 pole fully insulated plug-in bridging bar 838.00 1309 4006 63-125A 4 pole fully insulated plug-in bridging bar 1397.00 1309 4016 160A 4 pole fully insulated plug-in bridging bar 2122.00 1399 4006 1 pole tap-off terminal for power supply 558.00 2294 4016 4 pole terminal protection shroud 158.00 1309 0001 auxiliary contact 1NO + 1NC for each position (I-O-II) 1229.00 B-28

Motorised changeover switches 160A - 3200A ATyS R motorised changeover switches ATyS R are three-phase motorised changeover switches with positive break indication. They enable the on load transfer of two three-phase supplies via remote volt-free contacts, from either an external automatic controller, using pulse logic, or a switch. new Integrated auxiliary contacts (one contact for each position) Wide-band AC control voltage ± 20% Fail-safe mechanical interlock Padlockable in the OFF position Fully independent position auxiliary contacts one for each position ( I / O / II ) AC-31 B dimensions (mm) poles 415V (A) (H) (W) (D) ATyS R motorised changeover switches supply: 230Vac (previously ATyS 3s) 3 pole switches 9523 4016 9523 3016 160A 3 pole motorised changeover switch 135 287 244 14278.00 9523 3025 250A 3 pole motorised changeover switch 160 328 244 17810.00 9523 3040 400A 3 pole motorised changeover switch 170 328 244 24052.00 9523 3063 630A 3 pole motorised changeover switch 260 377 321 28692.00 9523 3080 800A 3 pole motorised changeover switch 321 504 392 44589.00 9523 3100 1000A 3 pole motorised changeover switch 321 504 392 47664.00 9523 3120 1250A 3 pole motorised changeover switch 330 504 392 56148.00 9523 3160 1600A 3 pole motorised changeover switch 288 596 392 68531.00 4 pole switches 9523 4016 160A 4 pole motorised changeover switch 135 317 244 16766.00 9523 4025 250A 4 pole motorised changeover switch 160 395 244 21287.00 9523 4040 400A 4 pole motorised changeover switch 170 395 244 28428.00 9523 4063 630A 4 pole motorised changeover switch 260 454 321 35456.00 9523 4080 800A 4 pole motorised changeover switch 321 584 392 49001.00 9523 4100 1000A 4 pole motorised changeover switch 321 584 392 53702.00 9523 4120 1250A 4 pole motorised changeover switch 330 584 392 56867.00 9523 4160 1600A 4 pole motorised changeover switch 288 716 392 78793.00 Larger sizes (up to 3200A) available on request ATyS G automatic changeover switches supply: 230Vac (previously ATyS 3e + 6e) ATyS G products are automatic changeover switches intended specifically for transformer/generator applications. The integrated controller provides all functions necessary for these applications, including monitoring the voltage and frequency of both sources, and on load changeover switching between two power supply sources, configured via four potentiometers and four DIP switches. Integrated dual power supply (2 independent supplies within the switch) Integrated generator on-load and off-load test function Fail-safe mechanical interlock Padlockable in the OFF position Fully independent position auxiliary contacts one for each position ( I / O / II ) 9553 4016 ATyS G Automatic changeover switches (for standby generators) 3 pole switches 9553 3016 160A 3 pole motorised changeover switch 135 287 244 23582.00 9553 3025 250A 3 pole motorised changeover switch 160 328 244 27115.00 9553 3040 400A 3 pole motorised changeover switch 170 328 244 33356.00 9553 3063 630A 3 pole motorised changeover switch 260 377 321 37996.00 9553 3080 800A 3 pole motorised changeover switch 321 504 392 63045.00 9553 3100 1000A 3 pole motorised changeover switch 321 504 392 66120.00 9553 3120 1250A 3 pole motorised changeover switch 330 504 392 74604.00 9553 3160 1600A 3 pole motorised changeover switch 288 596 392 86987.00 4 pole switches 9553 4016 160A 4 pole motorised changeover switch 135 317 244 26070.00 9553 4025 250A 4 pole motorised changeover switch 160 395 244 30591.00 9553 4040 400A 4 pole motorised changeover switch 170 395 244 37732.00 9553 4063 630A 4 pole motorised changeover switch 260 454 321 44761.00 9553 4080 800A 4 pole motorised changeover switch 321 584 392 67458.00 9553 4100 1000A 4 pole motorised changeover switch 321 584 392 72159.00 9553 4120 1250A 4 pole motorised changeover switch 330 584 392 75323.00 9553 4160 1600A 4 pole motorised changeover switch 288 716 392 97250.00 Larger sizes (up to 3200A) available on request B-29

Motorised changeover switch 250A-3200A / Accessories for changeover switches new 9573 4025 2694 4051 1559 4012 ATyS P automatic changeover switches (digital display) ATyS P products are automatic changeover switches intended specifically for power management applications enabling effective monitoring of installations thanks to time-stamped event recording. Events can be retrieved and read via the communication system. Particularly suited to energy and monitoring. Optional communication modules RS-485 or Ethernet Recording of events Possibilty to set periodic genset startup Power measurements Programmable inputs/outputs can be utilised to control load shedding based on load level or tariff current poles dimensions (mm) (H) (W) (D) ATyS P automatic changeover switches (previously ATyS 6m) 3 pole switches 9573 3025 250A 3 pole motorised ch/over switch 160 328 244 33893.00 9573 3040 400A 3 pole motorised ch/over switch 170 328 244 41695.00 9573 3063 630A 3 pole motorised ch/over switch 260 377 321 47495.00 9573 3080 800A 3 pole motorised ch/over switch 321 504 392 78807.00 9573 3120 1250A 3 pole motorised ch/over switch 330 504 392 93255.00 9573 3160 1600A 3 pole motorised ch/over switch 288 596 392 111343.00 4 pole switches 9573 4025 250A 4 pole motorised ch/over switch 160 395 244 38239.00 9573 4040 400A 4 pole motorised ch/over switch 170 395 244 47165.00 9573 4063 630A 4 pole motorised ch/over switch 260 454 321 55951.00 9573 4080 800A 4 pole motorised ch/over switch 321 584 392 84322.00 9573 4120 1250A 4 pole motorised ch/over switch 330 584 392 94154.00 9573 4160 1600A 4 pole motorised ch/over switch 288 716 392 124479.00 Larger sizes (up to 3200A) available on request Accessories for ATyS switches poles for switch 2694 3014 3 pole terminal protection shroud 160A 347.00 2694 3021 3 pole terminal protection shroud 250/400A 390.00 2694 3051 3 pole terminal protection shroud 630A 586.00 2694 4021 4 pole terminal protection shroud 250/400A 471.00 2694 4051 4 pole terminal protection shroud 630A 682.00 4109 0019 1 pole bridging bar for ch/over switches 160A 310.00 4109 0025 1 pole bridging bar for ch/over switches 250A 321.00 4109 0039 1 pole bridging bar for ch/over switches 400A 395.00 4109 0063 1 pole bridging bar for ch/over switches 630A 609.00 4109 0080 1 pole bridging bar for ch/over switches 800/1000A 953.00 4109 0120 1 pole bridging bar for ch/over switches 1250A 1399.00 4109 0160 1 pole bridging bar for ch/over switches 1600A 2116.00 1559 3012 3 pole voltage sense and p/supply harness 160A 1404.00 1559 3025 3 pole voltage sense and p/supply harness 250A 1644.00 1559 3040 3 pole voltage sense and p/supply harness 400A 1847.00 1559 3063 3 pole voltage sense and p/supply harness 630A 1994.00 1559 3080 3 pole voltage sense and p/supply harness 800/1000A 2392.00 1559 3120 3 pole voltage sense and p/supply harness 1250A 2470.00 1559 3160 3 pole voltage sense and p/supply harness 1600A 2509.00 1559 4012 N-right 4 pole voltage sense and p/supply harness 200/250A 1472.00 1559 4025 N-right 4 pole voltage sense and p/supply harness 200/250A 1722.00 1559 4040 N-right 4 pole voltage sense and p/supply harness 400A 1925.00 1559 4063 N-right 4 pole voltage sense and p/supply harness 630A 2108.00 1559 4080 N-right 4 pole voltage sense and p/supply harness 800/1000A 2586.00 1559 4120 N-right 4 pole voltage sense and p/supply harness 1250A 2606.00 1559 4160 N-right 4 pole voltage sense and p/supply harness 1600A 2626.00 4825 0092 plug-in RS485 MODBUS communication module all ATyS P 1291.00 4825 0094 plug-in plug-in 2 input and 2 output module all ATyS P 1071.00 4825 0203 plug-in Ethernet communication module all ATyS P 3921.00 4825 0204 plug-in Ethernet communication + RS485 JBUS/MODBUS all ATyS P 7116.00 1599 2010 remote control interface (panel mount) all ATyS P 2262.00 1599 2020 remote control interface with display (panel mount) all ATyS P 3637.00 1599 2009 connecting cable for (above) remote interfaces all ATyS P 234.00 1509 0001 mounting spacers (stackable) raises switch by 10mm (2 per set) 260.00 1529 0012 3/4 pole door protective frame for switches ATyS R 160-630A 504.00 1529 0080 3/4 pole door protective frame for switches ATyS R 800-1600A 586.00 1539 0012 3/4 pole door protective frame for switches ATySg/p 160-630A 813.00 1539 0080 3/4 pole door protective frame for switches ATySg/p 800-1600A 866.00 1599 5112 24Vdc-230Vac p/supply to operate switches with DC all ATyS R/G/P 8386.00 1599 4001 dual power supply permits remote transfer to any position all ATyS R 2304.00 B-30

Enclosed automatic changeover panels 63A - 1600A Enclosed automatic changeover panels ATyS automatic changeover panel is a complete AMS (automatic mains failure) switch in an enclosure. The internal ATyS G switch features an integrated controller which monitors the voltage and frequency of both the mains and generator supply. Should the monitored conditions move beyond the pre-configured parameters, the switch provides a generator start signal and once the generator voltage and frequency reach within the preset limits, the switch changes over to the generator supply, when mains are restored the switch changes back to the mains supply and provides a generator stop signal. Easy parameter setup via four potentiometers and DIP switches Integrated dual power supply (2 independent supplies within the switch) Integrated generator on-load and off-load test function Fail-safe mechanical interlock Supplied complete with bridge bars on output side manual override key/handle AC-31 B supply dimensions (mm) poles 415V (A) voltage (H) (W) (D) ATyS M automatic changeover systems 2 pole switches 40-160A EAC2004M 40A 230 Vac 2 pole automatic ch/over panel 550 400 220 14080.00 EAC2006M 63A 230 Vac 2 pole automatic ch/over panel 550 400 220 14620.00 EAC2008M 80A 230 Vac 2 pole automatic ch/over panel 550 400 220 15080.00 EAC2010M 100A 230 Vac 2 pole automatic ch/over panel 550 400 220 15680.00 4 pole switches EAC4004M 63A 230 Vac 4 pole automatic ch/over panel 550 400 220 17840.00 EAC4006M 80A 230 Vac 4 pole automatic ch/over panel 550 400 220 18140.00 EAC4015M 100A 230 Vac 4 pole automatic ch/over panel 550 400 220 19080.00 EAC4012M 125A 230 Vac 4 pole automatic ch/over panel 550 400 220 19690.00 EAC4016M 160A 231 Vac 4 pole automatic ch/over panel 550 400 220 22790.00 ATyS G automatic changeover systems 3 pole switches 250-1600A EAC3025M 250A 230 Vac 3 pole automatic ch/over panel 950 700 330 34160.00 EAC3040M 400A 230 Vac 3 pole automatic ch/over panel 950 700 330 40630.00 EAC3063M 630A 230 Vac 3 pole automatic ch/over panel 950 700 330 46060.00 EAC3080M 800A 230 Vac 3 pole automatic ch/over panel 1200 900 600 80140.00 EAC3100M 1000A 230 Vac 3 pole automatic ch/over panel 1200 900 600 83210.00 EAC3125M 1250A 230 Vac 3 pole automatic ch/over panel 1200 900 600 93220.00 EAC3160M 1600A 230 Vac 3 pole automatic ch/over panel 1200 900 600 107790.00 4 pole switches EAC4025M 250A 230 Vac 4 pole automatic ch/over panel 950 700 330 45290.00 EAC4040M 400A 230 Vac 4 pole automatic ch/over panel 950 700 330 52840.00 EAC4063M 630A 230 Vac 4 pole automatic ch/over panel 950 700 330 61000.00 EAC4080M 800A 230 Vac 4 pole automatic ch/over panel 1200 900 600 85880.00 EAC4100M 1000A 230 Vac 4 pole automatic ch/over panel 1200 900 600 90580.00 EAC4125M 1250A 230 Vac 4 pole automatic ch/over panel 1200 900 600 95470.00 EAC4160M 1600A 230 Vac 4 pole automatic ch/over panel 1200 900 600 120280.00 Larger sizes (up to 3200A) available on request B-31

Switch fuses 32A - 1250A 3631 3003 FUSERBLOC Fuse combination switches FUSERBLOC are manually operated multipole fuse combination switches. They make and break on load and provide safety isolation and protection against overcurrent in any low voltage electrical circuit. Complete isolation of fuses with double breaking per pole (top and bottom of fuse) Positive break indication Test position for testing control circuits without power (enclosure door can be opened in test position) External front operating handle and shaft (to be ordered seperately-see below) IEC/EN 60947-3, IEC/EN 60269-1, IEC/EN 60269-2, VDE 0636-1, VDE 0660-107 AC-22 A AC-23 A fuse dimensions (mm) 415V (A) 400V (kw) (H) (W) (D) NFC Cylindrical fuses (3 pole) 3631 3003 CD32A 15kW 10x38 fuse combination switch 98 96 65 1083.00 3831 3005 50A 25kW 14x51 fuse combination switch 118 121 87 1353.00 3831 3011 125A 63kW 22x58 fuse combination switch 162 148 132 2056.00 DIN pattern fuses 3841 3003 3831 3006 63A 30kW 00C fuse combination switch 118 136 132 1515.00 3831 3012 125A 63kW 00C fuse combination switch 160 148 132 2273.00 3831 3015 160A 80kW 00 fuse combination switch 160 148 132 2544.00 3831 3024 250A 132kW 1 fuse combination switch 195 234 146 3734.00 3831 3039 400A 220kW 2 fuse combination switch 205 252 149 5086.00 3811 3063 630A 355kW 3 fuse combination switch 300 364 250 10442.00 3811 3080 800A 450kW 3 fuse combination switch 300 364 250 12551.00 3811 3120 1250A 560kW 4 fuse combination switch 300 442 289 22722.00 BS88 pattern fuses 3831 3006 3641 3001 CD32A 15kW A1 fuse combination switch 98 96 83 1190.00 3841 3003 32A 15kW A1 fuse combination switch 118 121 85 1353.00 3841 3006 63A 30kW A2-A3 fuse combination switch 118 136 132 1515.00 3841 3010 100A 51kW A4 fuse combination switch 162 148 132 1840.00 3841 3015 160A 80kW A4 fuse combination switch 162 190 137 2544.00 3841 3021 200A 100kW B1-B2 fuse combination switch 195 234 146 3409.00 3841 3024 250A 132kW B1-B2-B3 fuse combination switch 195 234 146 3734.00 3841 3032 315A 160kW B1-B2-B3 fuse combination switch 205 252 149 4437.00 3841 3038 400A 220kW B2-B3-B4 fuse combination switch 205 252 149 5086.00 3821 3063 630A 355kW C1-C2 fuse combination switch 300 364 250 10442.00 3821 3080 800A 450kW C1-C2-C3 fuse combination switch 300 364 250 12551.00 3821 3120 1250A 560kW D1 fuse combination switch 300 442 289 22722.00 Operating handles and shafts for above switches (IP65) External front operated, door interlocking, padlockable (3 padlocks) in off with test position handle colour for switch 3821 3063 1413 2115 S1 black pistol grip operating handle (external) 32-63A 260.00 1423 2115 S2 black pistol grip operating handle (external) 100-400A 308.00 1433 3111 S2 black pistol grip operating handle (external) 630-800A 644.00 1443 3111 S4 black pistol grip operating handle (external) 1250A 807.00 Extension shafts for above switches handle length mm² for switch 3999 0600 1443 3111 1401 0540 1401 0532 S1 320mm 5 extension shaft for switch CD32A 245.00 1401 0540 S1 400mm 5 extension shaft for switch CD32A 274.00 1400 1020 S2 200mm 10 extension shaft for switch 32-400A 114.00 1400 1032 S3 320mm 10 extension shaft for switch 32-400A 126.00 1400 1050 S4 500mm 10 extension shaft for switch 33-400A 321.00 1400 1232 S3 320mm 12 extension shaft for switch 630~1250A 337.00 1400 1250 S3 500mm 12 extension shaft for switch 630~1250A 656.00 1429 0000 shaft guide (permits engaging of misaligned shaft with handle) (all sizes) 93.00 Auxiliary contacts for switch fuses 3999 0701 1 NO auxiliary contact and support CD32-1250A 136.00 3999 0702 1 NC additional auxiliary contact CD32-1250A 136.00 3999 0710 contact holder for additional auxiliary contacts CD32A 390.00 3999 0600 contact holder for additional auxiliary contacts 32-400A 434.00 B-32

Terminal shrouds for switches Top and/or bottom protection against direct contact with the terminals or connection parts. Made of translucent material for ease of inspection without having to remove first. Shrouds also provide phase separation. poles for switches Terminal shrouds for SIRCO M/MV switches (top or bottom terminal protection) 2294 1005 1 pole terminal protection shroud for switches Sirco M 16-63A 33.00 2294 3005 3 pole terminal protection shroud for switches Sirco M 16-63A 71.00 2294 1009 1 pole terminal protection shroud for switches Sirco M 100A 44.00 2294 3009 3 pole terminal protection shroud for switches Sirco M 100A 104.00 2294 3016 3 pole terminal protection shroud for switches Sirco M/MV 125-160A 114.00 2294 4016 4 pole terminal protection shroud for switches Sirco M/MV 125-160A 158.00 2294 3005 Terminal shrouds for SIRCO AC switches Also provides phase separation for switches (top or bottom terminal protection) 2694 3014 3 pole terminal protection shroud for switches Sirco 125-160A 347.00 2694 3021 3 pole terminal protection shroud for switches Sirco 200-315A 390.00 2694 3051 3 pole terminal protection shroud for switches Sirco 315-630A 586.00 Inter-phase barriers (essential for use at 690V or in polluted or dusty atmosphere) 2998 0033 3 pole inter-phase barriers for switches Sirco 125-160A 196.00 2998 0023 3 pole inter-phase barriers for switches Sirco 200-315A 233.00 2998 0013 3 pole inter-phase barriers for switches Sirco 315-400A 270.00 Terminal screens 3998 3016 2698 3080 3 pole terminal protection screens for switches Sirco 630-1000A 426.00 2698 3120 3 pole terminal protection screens for switches Sirco 1250-1600A 784.00 2698 3200 3 pole terminal protection screens for switches Sirco 2000-3200A 1515.00 Terminal shrouds for FUSERBLOC fuse switches (top and/or bottom terminal protection) Also provides phase separation for switches 3998 3016 3 pole terminal protection shroud for switches Fuserbloc 100-160A 282.00 3998 3025 3 pole terminal protection shroud for switches Fuserbloc 200-400A 374.00 3898 3080 3 pole terminal protection shroud for switches Fuserbloc 630-800A 1023.00 3898 3120 3 pole terminal protection shroud for switches Fuserbloc 1250A 1218.00 B-33

Industrial cylindrical fuse-links 420... 421... 422... Cylindrical fuse links made of ceramic tube with high withstand to internal pressure and thermal shock, permitting very high breaking capacities in a compact fuse design. Melting elements are specially designed to avoid ageing thus maintaining their electrical characteristics over time. Standards: IEC/EN 60269-1, IEC/EN 60269-2 rated rated breaking dimensions current voltage capacity (mm) gg cylindrical fuse links gg class for use as general protection against overloads and short circuits, intended as protection of cables, power lines and equipment. 10 x 38mm cylindrical fuses 420000 0.5A 500V 120kA 10 x 38 gg cylindrical fuse link 7.80 420001 1A 500V 120kA 10 x 38 gg cylindrical fuse link 7.00 420002 2A 500V 120kA 10 x 38 gg cylindrical fuse link 7.00 420004 4A 500V 120kA 10 x 38 gg cylindrical fuse link 7.00 420006 6A 500V 120kA 10 x 38 gg cylindrical fuse link 7.00 420010 10A 500V 120kA 10 x 38 gg cylindrical fuse link 7.00 420016 16A 500V 120kA 10 x 38 gg cylindrical fuse link 7.00 420020 20A 500V 120kA 10 x 38 gg cylindrical fuse link 7.00 420025 25A 500V 120kA 10 x 38 gg cylindrical fuse link 7.80 420032 32A 400V 120kA 10 x 38 gg cylindrical fuse link 7.80 14 x 51mm cylindrical fuses 421010 10A 690V 80kA 14 x 51 gg cylindrical fuse link 11.70 421016 16A 690V 80kA 14 x 51 gg cylindrical fuse link 11.70 421020 20A 690V 80kA 14 x 51 gg cylindrical fuse link 12.10 421025 25A 690V 80kA 14 x 51 gg cylindrical fuse link 12.10 421032 32A 500V 120kA 14 x 51 gg cylindrical fuse link 12.10 421040 40A 500V 120kA 14 x 51 gg cylindrical fuse link 12.50 421050 50A 400V 120kA 14 x 51 gg cylindrical fuse link 12.50 22 x 58mm cylindrical fuses 422032 32A 690V 80kA 22 x 58 gg cylindrical fuse link 24.00 422040 40A 690V 80kA 22 x 58 gg cylindrical fuse link 24.00 422050 50A 690V 80kA 22 x 58 gg cylindrical fuse link 25.00 422063 63A 690V 80kA 22 x 58 gg cylindrical fuse link 25.00 422080 80A 500V 120kA 22 x 58 gg cylindrical fuse link 26.00 422000 100A 500V 120kA 22 x 58 gg cylindrical fuse link 27.00 422015 125A 400V 120kA 22 x 58 gg cylindrical fuse link 28.00 4212... gg class cylindrical fuse links with striker For use with holder incorporating a micro switch to provide remote indication of blown fuse 14 x 51mm cylindrical fuses 421204 4A 500V 120kA 14 x 51 gg fuse link with striker 45.00 421206 6A 500V 120kA 14 x 51 gg fuse link with striker 45.00 421210 10A 500V 120kA 14 x 51 gg fuse link with striker 45.00 421216 16A 500V 120kA 14 x 51 gg fuse link with striker 45.00 421220 20A 500V 120kA 14 x 51 gg fuse link with striker 45.00 421225 25A 500V 120kA 14 x 51 gg fuse link with striker 45.00 421232 32A 500V 120kA 14 x 51 gg fuse link with striker 48.00 421240 40A 500V 120kA 14 x 51 gg fuse link with striker 48.00 421250 50A 400V 120kA 14 x 51 gg fuse link with striker 48.00 22 x 58mm cylindrical fuses 4222... 422232 32A 690V 80kA 22 x 58 gg fuse link with striker 66.00 422240 40A 690V 80kA 22 x 58 gg fuse link with striker 66.00 422250 50A 690V 80kA 22 x 58 gg fuse link with striker 69.00 422263 63A 690V 80kA 22 x 58 gg fuse link with striker 69.00 422280 80A 500V 120kA 22 x 58 gg fuse link with striker 75.00 422200 100A 500V 120kA 22 x 58 gg fuse link with striker 75.00 422215 125A 400V 120kA 22 x 58 gg fuse link with striker 75.00 433... 432... 431... Solid neutral links 431000 32A 10 x 38 gg/am solid neutral link 6.20 432000 50A 14 x 51 gg/am solid neutral link 10.60 433000 125A 22 x 58 gg/am solid neutral link 18.50 B-34

Industrial cylindrical fuse-links am fuse links for short circuit protection of motors, transformers and other loads with high inrush currents. Excellent protection of switchgear due to the effective current limiting capabilities and low I²t values. Standards: IEC/EN 60269-1, IEC/EN 60269-2 rated rated breaking dimensions current voltage capacity (mm) am (motor protection) fuse links 440... 441... 10 x 38mm cylindrical fuses 440000 0.5A 500V 120kA 10 x 38 am cylindrical fuse link 7.40 440001 1A 500V 120kA 10 x 38 am cylindrical fuse link 7.40 440002 2A 500V 120kA 10 x 38 am cylindrical fuse link 7.40 440004 4A 500V 120kA 10 x 38 am cylindrical fuse link 7.40 440006 6A 500V 120kA 10 x 38 am cylindrical fuse link 7.40 440010 10A 500V 120kA 10 x 38 am cylindrical fuse link 7.40 440016 16A 500V 120kA 10 x 38 am cylindrical fuse link 7.40 440020 20A 400V 120kA 10 x 38 am cylindrical fuse link 7.40 440025 25A 400V 120kA 10 x 38 am cylindrical fuse link 7.40 14 x 51mm cylindrical fuses 441020 20A 690V 80kA 14 x 51 am cylindrical fuse link 12.00 441025 25A 690V 80kA 14 x 51 am cylindrical fuse link 12.00 441032 32A 500V 120kA 14 x 51 am cylindrical fuse link 12.00 441040 40A 500V 120kA 14 x 51 am cylindrical fuse link 12.80 441050 50A 400V 120kA 14 x 51 am cylindrical fuse link 12.80 22 x 58mm cylindrical fuses 442032 32A 690V 80kA 22 x 58 am cylindrical fuse link 24.00 442040 40A 690V 80kA 22 x 58 am cylindrical fuse link 25.00 442050 50A 690V 80kA 22 x 58 am cylindrical fuse link 25.00 442063 63A 690V 80kA 22 x 58 am cylindrical fuse link 27.00 442080 80A 500V 120kA 22 x 58 am cylindrical fuse link 27.00 442000 100A 500V 120kA 22 x 58 am cylindrical fuse link 28.00 442015 125A 400V 120kA 22 x 58 am cylindrical fuse link 29.00 gr RAPIDPLUS high speed fuse links for semiconductors 442... gr cylindrical high speed fuse-links provide optimum protection of semiconductor devices (thyristors, triacs, diodes, rectifiers, static relays, etc.) provides protection of overloads and short circuits. Melting elements are specially designed to obtain low I²t values and reduce arc voltages to provide adequate selective coordination with upstream fuse links. Typical applications include protection of rectifiers, UPS, motor drives, soft starters and inverters. Standards: IEC/EN 60269-1, IEC/EN 60269-4 492003 4A 690V 100kA 10 x 38 gr semiconductor fuse link 41.00 492004 6A 690V 100kA 10 x 38 gr semiconductor fuse link 41.00 492006 10A 690V 100kA 10 x 38 gr semiconductor fuse link 41.00 492008 16A 690V 100kA 10 x 38 gr semiconductor fuse link 41.00 492009 20A 690V 100kA 10 x 38 gr semiconductor fuse link 41.00 492010 25A 690V 100kA 10 x 38 gr semiconductor fuse link 41.00 492011 32A 690V 100kA 10 x 38 gr semiconductor fuse link 41.00 492022 32A 690V 100kA 14 x 51 gr semiconductor fuse link 69.00 492023 40A 690V 100kA 14 x 51 gr semiconductor fuse link 69.00 492024 50A 690V 100kA 14 x 51 gr semiconductor fuse link 69.00 4920... 492037 50A 690V 100kA 22 x 58 gr semiconductor fuse link 85.00 492038 63A 690V 100kA 22 x 58 gr semiconductor fuse link 124.00 492039 80A 690V 100kA 22 x 58 gr semiconductor fuse link 124.00 492040 100A 690V 100kA 22 x 58 gr semiconductor fuse link 124.00 492123 492139 gr high speed fuse links for semiconductors with striker 492117 10A 690V 100kA 14 x 51 gr semiconductor fuse link 104.00 492119 16A 690V 100kA 14 x 51 gr semiconductor fuse link 104.00 492120 20A 690V 100kA 14 x 51 gr semiconductor fuse link 104.00 492121 25A 690V 100kA 14 x 51 gr semiconductor fuse link 104.00 492122 32A 690V 100kA 14 x 51 gr semiconductor fuse link 104.00 492123 40A 690V 100kA 14 x 51 gr semiconductor fuse link 104.00 492124 50A 690V 100kA 14 x 51 gr semiconductor fuse link 104.00 492137 50A 690V 100kA 22 x 58 gr semiconductor fuse link 131.00 492138 63A 690V 100kA 22 x 58 gr semiconductor fuse link 171.00 492139 80A 690V 100kA 22 x 58 gr semiconductor fuse link 171.00 492140 100A 690V 100kA 22 x 58 gr semiconductor fuse link 171.00 B-35

Industrial modular cylindrical fuse holders 485101 485050 485359 483530 new 485205 485305 480005 485360 new 483534 PMX series modular fuseholders Modular, compact fuse holder DIN rail mountable for cylindrical fuses Incorporated, hinged transparent label holder for positive circuit identification Optimized ventilation zones for improved heat dissipation High temperature resistance, self-extinguishing-halogen free body / silver plated copper contacts Standards: IEC/EN 60269-1, IEC/EN 60269-2, IEC/EN 60947-3, CSA C22.2 4248-1, UL4248-1 For 10 x 38mm fuse-links rated for fuse width in poles current size 17.5 (mm) (H) 88.8 x (W) 17.5 x (D) 58 mm 485101 32A 10 x 38 1 pole 1 industrial cylindrical fuseholder 33.00 485103 32A 10 x 38 1 pole+n 2 industrial cylindrical fuseholder 98.00 485104 32A 10 x 38 2 pole 2 industrial cylindrical fuseholder 92.00 485105 32A 10 x 38 3 pole 3 industrial cylindrical fuseholder 136.00 485107 32A 10 x 38 4 pole 4 industrial cylindrical fuseholder 182.00 With indicator 485108 32A 10 x 38 1 pole 1 with 120~690V neon indication 72.00 Accessories for 10x38mm fuse holder 480005 body pincers for multi-pole assembly of 10x38mm fuse holders 2.00 485050 handle pin for multi-pole assembly of 10x38mm fuse holders 2.00 485051 lock support for padlocking holder 10x38mm fuse holders 15.00 485053 phase separator accessory 10x38mm fuse holders 6.00 485054 replacement fusing neon indicator 120~690V 10x38mm fuse holders 19.00 For 14 x 51mm fuse-links (H) 110 x (W) 26.5 x (D) 76 mm 485201 50A 14 x 51 1 pole 1.5 industrial cylindrical fuseholder 91.00 485203 50A 14 x 51 1 pole+n 3 industrial cylindrical fuseholder 198.00 485205 50A 14 x 51 3 pole 4.5 industrial cylindrical fuseholder 295.00 With indicator (replaceable indicator module) 485208 50A 14 x 51 1 pole 1.5 with 120~690V neon indication 120.00 Accessories for 14x51mm fuse holder 480005 body pincers for multi-pole assembly of 14x51mm fuse holders 2.00 485356 handle pin for multi-pole assembly of 14x51mm fuse holders 4.00 485357 micro switch ties for multiple assembly for 14x51mm fuse holders 6.00 485258 lock support for padlocking holder 14x51mm fuse holders 9.00 485259 micro switch 1 pole for use with fuses with striker 72.00 485260 micro switch 3 pole for use with fuses with striker 89.00 485262 micro switch unipolar extension 14x51mm fuse holders 16.00 485264 replacement fusing neon indicator 120~690V 14x51mm fuse holders 44.00 For 22 x 58mm fuse-links (H) 126.5 x (W) 35.5 x (D) 76.5 mm 485301 125A 22 x 58 1 pole 2 industrial cylindrical fuseholder 182.00 485303 125A 22 x 58 1 pole+n 4 industrial cylindrical fuseholder 405.00 485305 125A 22 x 58 3 pole 6 industrial cylindrical fuseholder 572.00 With indicator (indicator module replaceable) 485308 125A 22 x 58 1 pole 2 with 120~690V neon indication 238.00 Although all our 22 x 58 cylindrical fuse links are rated at 125A, they are marked at 100A in order to conform to IEC/EN 60269-2 requirements Accessories for 22 x 58mm fuse holder 480005 body pincers for multi-pole assembly of 22x58mm fuse holders 2.00 485356 handle pin for multi-pole assembly of 22x58mm fuse holders 4.00 485357 micro switch ties for multiple assembly of 22x58mm fuse holders 6.00 485358 padlocking facility accessory 22x58mm fuse holders 10.00 485359 micro switch 1 pole for use with fuses with striker 76.00 485360 micro switch 3 pole for use with fuses with striker 93.00 485362 micros switch unipolar extension 22x58mm fuse holders 17.00 485364 replacement fusing neon indicator 120~690V 22x58mm fuse holders 38.00 PMC series compact modular fuseholders low profile (38.5mm) Compact fuse holders with very shallow dimension suitable for installation into low profile enclosures. For 10 x 38mm fuse-links (H) 82.7 x (W) 17.8 x (D) 38.5 mm 483530 32A 10 x 38 1 pole 1 compact cylindrical fuseholder 42.00 483534 32A 10 x 38 1 pole+n 1 compact cylindrical fuseholder 68.00 Accessories for compact 10x38mm fuse holder 480005 body pincers for multi-pole assembly of 10x38mm PMC fuse holders 2.00 483550 handle pin for multi-pole assembly of 10x38mm PMC fuse holders 3.00 Above prices do not include VAT. E&OE B-36

NH industrial HRC fuses Knife (NH) fuse-links gg class for general use. High breaking capacity intended for protection of power lines and equipment against overloads and short-circuits. Ceramic body with high withstand to internal pressure and thermal shock, offering high breaking capacity. Manufactured according to IEC/EN60269 and VDE0636 Standards and comply with RoHS directive. Standards: IEC/EN 60269-1, IEC/EN 60269-2, DIN 43620 rated rated breaking fuse current voltage capacity size NH000 gg NH HRC fuse links 500V top indicator NH00 gg class for use as general protection against overloads and short circuits For protection of cables, power lines and equipment Fusing indicator on top of fuse link 381010 6A 500V 120kA NH000 gg DIN HRC fuse link 49.00 381015 10A 500V 120kA NH000 gg DIN HRC fuse link 49.00 381020 16A 500V 120kA NH000 gg DIN HRC fuse link 49.00 381025 20A 500V 120kA NH000 gg DIN HRC fuse link 49.00 381030 25A 500V 120kA NH000 gg DIN HRC fuse link 42.00 381035 32A 500V 120kA NH000 gg DIN HRC fuse link 42.00 381045 40A 500V 120kA NH000 gg DIN HRC fuse link 42.00 381050 50A 500V 120kA NH000 gg DIN HRC fuse link 42.00 381055 63A 500V 120kA NH000 gg DIN HRC fuse link 42.00 381060 80A 500V 120kA NH000 gg DIN HRC fuse link 42.00 381065 100A 500V 120kA NH000 gg DIN HRC fuse link 42.00 381070 125A 500V 120kA NH00 gg DIN HRC fuse link 57.00 381075 160A 500V 120kA NH00 gg DIN HRC fuse link 57.00 NH1 381255 160A 500V 120kA C1 gg DIN HRC fuse link 82.00 381260 200A 500V 120kA NH1 gg DIN HRC fuse link 129.00 381270 250A 500V 120kA NH1 gg DIN HRC fuse link 129.00 381280 315A 500V 120kA NH1 gg DIN HRC fuse link 129.00 381285 355A 500V 120kA NH1 gg DIN HRC fuse link 129.00 381370 315A 500V 120kA NH2 gg DIN HRC fuse link 146.00 381375 355A 500V 120kA NH2 gg DIN HRC fuse link 146.00 381380 400A 500V 120kA NH2 gg DIN HRC fuse link 146.00 381390 500A 500V 120kA NH2 gg DIN HRC fuse link 146.00 381465 500A 500V 120kA NH3 gg DIN HRC fuse link 281.00 381470 630A 500V 120kA NH3 gg DIN HRC fuse link 281.00 381475 800A 500V 120kA NH3 gg DIN HRC fuse link 281.00 381525 800A 500V 120kA NH4 gg DIN HRC fuse link 867.00 381530 1000A 500V 120kA NH4 gg DIN HRC fuse link 867.00 381535 1250A 500V 120kA NH4 gg DIN HRC fuse link 867.00 NH2 gg NH HRC fuse links 690V top indicator 382010 6A 690V 80kA NH000 gg DIN HRC fuse link 98.00 382015 10A 690V 80kA NH000 gg DIN HRC fuse link 94.00 382020 16A 690V 80kA NH000 gg DIN HRC fuse link 94.00 382025 20A 690V 80kA NH000 gg DIN HRC fuse link 95.00 382030 25A 690V 80kA NH000 gg DIN HRC fuse link 96.00 382035 32A 690V 80kA NH000 gg DIN HRC fuse link 96.00 382045 40A 690V 80kA NH000 gg DIN HRC fuse link 96.00 382050 50A 690V 80kA NH00 gg DIN HRC fuse link 103.00 382055 63A 690V 80kA NH00 gg DIN HRC fuse link 103.00 382060 80A 690V 80kA NH00 gg DIN HRC fuse link 103.00 382065 100A 690V 80kA NH00 gg DIN HRC fuse link 103.00 382250 125A 690V 80kA NH1 gg DIN HRC fuse link 158.00 382255 160A 690V 80kA NH1 gg DIN HRC fuse link 158.00 382260 200A 690V 80kA NH1 gg DIN HRC fuse link 158.00 382360 250A 690V 80kA NH2 gg DIN HRC fuse link 273.00 382370 315A 690V 80kA NH2 gg DIN HRC fuse link 288.00 382450 355A 690V 80kA NH3 gg DIN HRC fuse link 389.00 382455 400A 690V 80kA NH3 gg DIN HRC fuse link 392.00 382465 500A 690V 80kA NH3 gg DIN HRC fuse link 399.00 NH3 382520 630A 690V 80kA NH4 gg DIN HRC fuse link 1413.00 382525 800A 690V 80kA NH4 gg DIN HRC fuse link 1413.00 Fuse bases for above (see page B-39) B-37

NH industrial HRC fuses 384035 384065 341250 new 371470 am (motor protection) fuse links am class (NH) for motor protection. These high breaking capacity fuse-links are intended for short circuit protection in motors, transformers and other loads with high inrush currents, with rated voltages up to 500Vac (120kA) and 690Vac (80kA). They offer excellent protection of switchgear (contactor, thermal overloads) due to the good current limiting capability and low I²t values. Standards: IEC/EN 60269-1, IEC/EN 60269-2 and VDE43620 rated rated breaking fuse current voltage capacity size am NH (motor protection) fuse links 500/690V top indicator 384010 6A 690V 80kA NH000 am HRC DIN fuse link 103.00 384015 10A 690V 80kA NH000 am HRC DIN fuse link 99.00 384020 16A 690V 80kA NH000 am HRC DIN fuse link 99.00 384025 20A 690V 80kA NH000 am HRC DIN fuse link 100.00 384030 25A 690V 80kA NH000 am HRC DIN fuse link 100.00 384035 32A 690V 80kA NH000 am HRC DIN fuse link 100.00 384045 40A 690V 80kA NH000 am HRC DIN fuse link 100.00 384050 50A 690V 80kA NH00 am HRC DIN fuse link 106.00 384055 63A 690V 80kA NH00 am HRC DIN fuse link 106.00 384060 80A 690V 80kA NH00 am HRC DIN fuse link 107.00 384065 100A 690V 80kA NH00 am HRC DIN fuse link 114.00 383070 125A 500V 120kA NH00 am HRC DIN fuse link 114.00 383075 160A 500V 120kA NH00 am HRC DIN fuse link 118.00 384260 200A 690V 80kA NH1 am HRC DIN fuse link 185.00 383270 250A 500V 120kA NH1 am HRC DIN fuse link 195.00 384370 315A 690V 80kA NH2 am HRC DIN fuse link 295.00 384375 355A 690V 80kA NH2 am HRC DIN fuse link 307.00 383380 400A 500V 120kA NH2 am HRC DIN fuse link 297.00 384465 500A 690V 80kA NH3 am HRC DIN fuse link 406.00 383470 630A 500V 120kA NH3 am HRC DIN fuse link 419.00 383525 800A 500V 120kA NH4 am HRC DIN fuse link 1084.00 383530 1000A 500V 120kA NH4 am HRC DIN fuse link 1104.00 383535 1250A 500V 120kA NH4 am HRC DIN fuse link 1429.00 gs RAPIDPLUS high-speed fuse-links for semi-conductors RAPIDPLUS NH gs fuse links clear all s of overcurrents, overloads and short-circuits, protecting semiconductors, cables and switchgear of the installation. Optimized for reduced power dissipation, permitting utilization of a wide range of applications. Typical application comprise protection of semiconductors (diodes, thyristors, triacs, etc) used in power rectifiers, UPS, converters, motor drives, soft starters, solid state relays, photovoltaic inverters, welding inverters to protect semiconductor devices. 371025 20A 690V 100kA NH000 gs HRC DIN fuse link 265.00 371030 25A 690V 100kA NH000 gs HRC DIN fuse link 276.00 371035 32A 690V 100kA NH000 gs HRC DIN fuse link 286.00 371045 40A 690V 100kA NH000 gs HRC DIN fuse link 293.00 371050 50A 690V 100kA NH000 gs HRC DIN fuse link 303.00 371055 63A 690V 100kA NH000 gs HRC DIN fuse link 329.00 371060 80A 690V 100kA NH000 gs HRC DIN fuse link 363.00 371065 100A 690V 100kA NH000 gs HRC DIN fuse link 425.00 371070 125A 690V 100kA NH00 gs HRC DIN fuse link 518.00 371075 160A 690V 100kA NH00 gs HRC DIN fuse link 603.00 371260 200A 690V 100kA NH1 gs HRC DIN fuse link 807.00 371270 250A 690V 100kA NH1 gs HRC DIN fuse link 957.00 371370 315A 690V 100kA NH2 gs HRC DIN fuse link 1674.00 371375 355A 690V 100kA NH2 gs HRC DIN fuse link 1823.00 371380 400A 690V 100kA NH2 gs HRC DIN fuse link 2096.00 371465 500A 690V 100kA NH3 gs HRC DIN fuse link 2651.00 371470 630A 690V 100kA NH3 gs HRC DIN fuse link 3489.00 Fuse bases for above (see page B-39) Isolating link blades for NH fuse bases 341100 160A 690V 1 pole NH000/00 isolating neutral link blades 78.00 341250 250A 690V 1 pole NH1 isolating neutral link blades 119.00 341400 400A 690V 1 pole NH2 isolating neutral link blades 142.00 341630 630A 690V 1 pole NH3 isolating neutral link blades 180.00 340125 1250A 690V 1 pole NH4 isolating neutral link blades 665.00 B-38

NH industrial DIN fuse bases ST series fuse bases for NH fuse-links Self-extinguishing polyamide body / silver plated copper contacts Rated voltage: 690V Standards: IEC/EN 60269-1, IEC/EN 60269-2, DIN43620 rated current for fuse size poles qty per pack 354115 325250 340001 353102 326250 ST series NH fuse bases Single pole 354115 160A NH000/00 1 pole industrial NH fuse base 1 68.00 354250 250A NH1 1 pole industrial NH fuse base 1 196.00 354400 400A NH2 1 pole industrial NH fuse base 1 265.00 354630 630A NH3 1 pole industrial NH fuse base 1 352.00 354125 1250A NH4 1 pole industrial NH fuse base 1 1350.00 Three pole (supplied with seperating phase barriers between fuses) 353102 160A NH000/00 3 pole industrial NH fuse base 1 220.00 355250 250A NH1 3 pole industrial NH fuse base 1 662.00 355400 400A NH2 3 pole industrial NH fuse base 1 863.00 355630 630A NH3 3 pole industrial NH fuse base 1 1152.00 DIN rail and chassis screw mount Sectionable neutral NH bases Neutral link base (can be mounted directly onto sides of fuse base) 334103 160A NH00 1 pole sectionable neutral terminal 1 78.00 334160 250A NH1 1 pole sectionable neutral terminal 1 104.00 334251 630A NH3 1 pole sectionable neutral terminal 1 155.00 NH fuse holder accessories Partition walls (NH00/1/2/3 require conectors to mount) 326100 160A NH00 partition walls for fuse bases 2 39.00 326250 250A NH1/2 partition walls for fuse bases 2 80.00 326630 630A NH3 partition walls for fuse bases 2 95.00 343125 1250A NH4 partition walls for fuse bases 1 127.00 Screws directly onto chassis plate (does not mount onto fuse base) Connectors (to connect two bases together - accepts partition wall) 325100 160A NH00 separators for fuse bases 2 16.00 325250 250A NH1/2 separators for fuse bases 2 27.00 325630 630A NH3 separators for fuse bases 2 48.00 Terminal covers (to protect connection terminals of fuse holders) 325000 160A NH00 1 pole terminal cover for bases 6 87.00 325009 160A NH00 3 pole integral terminal cover 1 68.00 325002 250A NH1 1 pole terminal cover for bases 6 160.00 325003 400A NH2 1 pole terminal cover for bases 6 209.00 325007 630A NH3 1 pole terminal cover for bases 6 352.00 Partition walls incorporated Fuse-link covers (connects onto terminal covers) 325010 160A NH00 hinged covers for fuse link 3 63.00 325020 250A NH1/2 hinged covers for fuse link 3 103.00 325025 630A NH3 hinged covers for fuse link 3 151.00 Complete fuse base protection kits (for fuse and terminal insulation protection IP20) Comprises - partition walls - terminal cover - fuse cover 325041 250A NH1 3 pole IP20 full protection kit 1 323.00 325046 400A NH2 3 pole IP20 full protection kit 1 337.00 325051 630A NH3 3 pole IP20 full protection kit 1 641.00 Accessories for NH fuse-links Microswitch (mounts directly onto fuse-links) 357010 5A 250Vac 1 pole NH000-3 micro switch for NH fuses 252.00 Fuse removal handle (universal for all sizes fuse-links) 340001 universal handle NH00-4 fuse replace/removal handle 216.00 B-39

Bolted HRC fuse links (BS88) FSA FGN... Industrial protection HRC fuses Rated voltage: 500 Vac Rated breaking capacity: 80 ka Standards specification: BS88-2, IEC 60269-2-1 Fuse class: gg/q1 rated BS88 rated breaking fixing body current ref. voltage capacity centres dia. (mm) (GEC) Off-set blade tag fuses (F1) body length 60 mm FGN 02A 2A A1/NP 500V 80kA offset blade 14.2 mm NS 18.00 FGN 04A 4A A1/NP 500V 80kA offset blade 14.2 mm NS 18.00 FGN 06A 6A A1/NP 500V 80kA offset blade 14.2 mm NS 18.00 FGN 10A 10A A1/NP 500V 80kA offset blade 14.2 mm NS 18.00 FGN 16A 16A A1/NP 500V 80kA offset blade 14.2 mm NS 18.00 FGN 20A 20A A1/NP 500V 80kA offset blade 14.2 mm NS 18.00 FGN 25A 25A A1/NP 500V 80kA offset blade 14.2 mm NS 18.00 FGN 32A 32A A1/NP 500V 80kA offset blade 14.2 mm NS 18.00 FSS... Off-set bolted tag (A2) body length 86 mm FSA 02A 2A A2 500V 80kA 73 mm 21.5 mm TIA 23.00 FSA 04A 4A A2 500V 80kA 73 mm 21.5 mm TIA 23.00 FSA 06A 6A A2 500V 80kA 73 mm 21.5 mm TIA 23.00 FSA 10A 10A A2 500V 80kA 73 mm 21.5 mm TIA 23.00 FSA 16A 16A A2 500V 80kA 73 mm 21.5 mm TIA 23.00 FSA 20A 20A A2 500V 80kA 73 mm 21.5 mm TIA 23.00 FSA 25A 25A A2 500V 80kA 73 mm 21.5 mm TIA 23.00 FSA 32A 32A A2 500V 80kA 73 mm 21.5 mm TIA 23.00 FSDCP... Off-set bolted tag (A3) body length 90 mm FSS 40 40A A3 500V 80kA 73 mm 21.5 mm TIS 26.00 FSS 50 50A A3 500V 80kA 73 mm 21.5 mm TIS 26.00 FSS 63 63A A3 500V 80kA 73 mm 21.5 mm TIS 26.00 FSFP... Off-set bolted tag (A4) body length 111 mm FSDCP 63 63A A4 500V 80kA 94 mm 32 mm TCP 58.00 FSDCP 80 80A A4 500V 80kA 94 mm 32 mm TCP 58.00 FSDCP 100 100A A4 500V 80kA 94 mm 32 mm TCP 58.00 Off-set bolted tag (A4) body length 111 mm FSFP 125 125A A4a 500V 80kA 94 mm 39.5 mm TFP 89.00 FSFP 160 160A A4a 500V 80kA 94 mm 39.5 mm TFP 89.00 FSFP 200 200A A4a 500V 80kA 94 mm 39.5 mm TFP 89.00 FSK... Central bolted tag (B2) body length 132 mm FSF 160 160A B2 500V 80kA 111 mm 39.5 mm TF 99.00 FSF 200 200A B2 500V 80kA 111 mm 39.5 mm TF 99.00 Central bolted tag (B3) body length 136 mm FSK 250 250A B3 500V 120kA 111 mm 50.5 mm TKF 155.00 FSK 315 315A B3 500V 120kA 111 mm 50.5 mm TKF 155.00 FMF... Central bolted tag (B4) body length 136 mm FMF 355 355A B4 500V 80kA 111 mm 50.5 mm TMF 195.00 FMF 400 400A B4 500V 80kA 111 mm 50.5 mm TMF 195.00 FTM... Central bolted tag (C2) body length 208 mm FTM 500 500A C2 500V 80kA 133/184 mm 70.2 mm TTM 380.00 FTM 600 600A C2 500V 80kA 133/184 mm 70.2 mm TTM 380.00 B-40

Switch disconnectors AC-21A AC-23A dimensions (mm) 690V 415V (H) (W) (D) GA series 3-pole load-break switches (4th pole attachable) Modular design DIN rail mountable supplied with direct mounted handle Door interlocking handle and shaft (to be ordered seperately) GA016A GA016A 16A 7.5kW 3-pole load-break switch 78 36 75 182.00 GA025A 25A 11.0kW 3-pole load-break switch 78 36 75 207.00 GA032A 32A 15.0kW 3-pole load-break switch 78 36 75 239.00 GA040A 40A 18.5kW 3-pole load-break switch 78 36 75 265.00 GA063SA 63A 22.0kW 3-pole load-break switch 78 36 75 373.00 GA080A 80A 45.0kW 3-pole load-break switch 100 70 75 627.00 GA125A 125A 55.0kW 3-pole load-break switch 100 70 75 731.00 Direct door mounting version (rear access terminals) with shaft 25-40A mounts through standard Ø22mm hole or chassis screw mount. GA040C GA025C 25A 11.0kW 3-pole load-break switch 78 36 73 234.00 GA040C 40A 18.5kW 3-pole load-break switch 78 36 73 291.00 GA080C 80A 45.0kW 3-pole load-break switch 100 70 70 679.00 GA125C 125A 55.0kW 3-pole load-break switch 100 70 70 783.00 Parallel attachment to convert 3/4 pole switches to 6/8 pole Used to combine two switches side-by-side to make up a 6/8 pole switch GAX6000 parallel attachment for combining 2 switches (6/8 pole) GA016-40A 306.00 GAX6001 parallel attachment for combining 2 switches (6/8 pole) GA0638A-125A 367.00 GA080C Changeover attachment for switches GAX5000 changeover mechanism interlock for 2 switches GA016-63A 335.00 GAX5001 changeover mechanism interlock for 2 switches GA080-125A 447.00 GAX67B black door interlocking handle (I-O-II) for above changeover mechanisms 153.00 Handles (external front operation) (IP65) External door interlocking handles padlockable (3 padlocks) in off position GAX1011A GAX61 red/yellow door interlocking recessed handle (screw fixing) GA016-63A/C 91.00 GAX632 red/yellow door interlocking handle (ring fix Ø 22mm hole) GA016-63A 131.00 GAX63 red/yellow door interlocking handle (ring fix Ø 22mm hole) GA016-40A/C 131.00 GAX64 red/yellow interlocking handle (ring fix Ø 22mm defeatable) GA016-63A 195.00 GAX66 red/yellow door interlocking pistol grip handle (screw fixing) GA080-125A 390.00 Requires GAX60B adaptor (below) and 7mm sq extension shaft GAX60B adaptor to accommodate 7mm sq shaft required for handles GAX66/66B 41.00 GAX61 GAX7200 GAX63 Extension shafts (for above switches/handles) GAX7200 200mm 5mm extension shaft for switches GA016-125A 43.00 GAX7300 300mm 5mm extension shaft for switches GA016-125A 59.00 GAX7200A 200mm 7mm extension shaft for handles GAX66/66B 83.00 GAX7300A 300mm 7mm extension shaft for handles GAX66/66B 115.00 Auxiliary contact blocks (Ith 16A) GAX1011A 1NO + 1NC auxiliary for base mount switches GA016-125A 159.00 GAX1011C 1NO + 1NC auxiliary for direct door mount switches GA016-125C 168.00 GAX1110EA 1NO (early-break) auxiliary for base mount switches GA016-63A 169.00 GAX1210EA 1NO (early-break) auxiliary for base mount switches GA080-125A 169.00 GAX60B Terminal shrouds GAX81 1 pole terminal protection shroud (2 pcs) GA016-63A/C 39.00 GAX82 1 pole terminal protection shroud (2 pcs) GA080-125A/C 63.00 GAX83 3 pole terminal protection shroud (2 pcs) GA016-63A/C 65.00 GAX84 3 pole terminal protection shroud (2 pcs) GA080-125A/C 108.00 GAX391 3 pole fuse holder for load-break switches 16-32A (for cylindrical 10x38mm fuses) GAX391 3 phase fuse holder attaches directly onto switches: GA016A - 040A 287.00 B-41

Enclosed isolators GAX42040A AC-21A 690V Attachable 4th pole for standard switches GAX42040A 40A attachable 4th pole for above switches GA016-40A 83.00 GAX42063SA 63A attachable 4th pole for above switches GA016-63A 135.00 GAX42125A 125A attachable 4th pole for above switches GA080-125A 196.00 GAX41040A 40A attachable early-make 4th pole for above switches GA016-63A 91.00 GAX41125A 125A attachable early-make 4th pole for above switches GA080-125A 217.00 Attachable 4th pole for door mount switches GAX42040C 40A attachable 4th pole for above switches GA016-40C 104.00 GAX42125C 125A attachable 4th pole for above switches GA063-125C 245.00 GAX41040C 40A attachable early-make 4th pole for above switches GA016-40C 115.00 GAX41125C 125A attachable early-make 4th pole for above switches GA063-125C 269.00 Enclosed Isolators GA series enclosed switch disconnectors are supplied in robust, heavy duty enclosures made of ABS material in an IP65 execution with a sealable front cover. The enclosures incorporate a red/yellow operating handle mechanically interlocked with cover in ON position, padlockable (3 padlocks) in the OFF position. AC-21A AC-23A dimensions (mm) 690V 415V (H) (W) (D) Enclosed isolators three pole (IP65) GAZ025 GAZ016 16A 7.5kW 3-pole enclosed load-break switch 160 100 120 404.00 GAZ025 25A 11.0kW 3-pole enclosed load-break switch 160 100 120 447.00 GAZ032 32A 15.0kW 3-pole enclosed load-break switch 160 100 120 504.00 GAZ040 40A 18.5kW 3-pole enclosed load-break switch 160 100 120 605.00 GAZ063EM 63A 22.0kW 3-pole enclosed load-break switch 160 100 120 655.00 GAZ080C 80A 45.0kW 3-pole enclosed load-break switch 210 175 122 1186.00 GAZ125CEM 125A 55.0kW 3-pole enclosed load-break switch 210 175 122 1371.00 For 4 pole please add attachable 4th pole (above) Enclosed isolators four pole (IP65) GAZ016 T4EM 16A 7.5kW 4-pole enclosed load-break switch 160 100 120 487.00 GAZ032 T4EM 32A 15.0kW 4-pole enclosed load-break switch 160 100 120 587.00 GAZ040 T4EM 40A 18.5kW 4-pole enclosed load-break switch 160 100 120 688.00 GAZ063 T4EM 63A 22.0kW 4-pole enclosed load-break switch 160 100 120 790.00 GAZ080C T4EM 80A 45.0kW 4-pole enclosed load-break switch 210 175 122 1382.00 GAZ125C T4EM 125A 55.0kW 4-pole enclosed load-break switch 210 175 122 1567.00 (Empty enclosures see page H-4) GAZ040 T4EM B-42

Industrial electronic earth leakage relays Industrial electronic earth leakage relays LED indication (Green Power ON ) ( Red TRIP) Front TEST and RESET buttons Configurable automatic or manual reset Configurable tripping set-point (I n): 0.025-0.25A / 0.25-2.5A / 2.5-25A Configurable tripping time delay (t): 0.02-0.5s / 0.2-5s Reference standards: IEC/EN 61010-1, IEC/EN 61000-6-2/3 supply voltage relays Panel mount earth leakage relays (96 x 96 mm) Require torroidal current transformers (listed below) R1D 1 operational threshold R1D 415 110-240-415V 1 earth leakage 1 operational threshold 3189.00 R4D 415 R2D 2 operational thresholds (configurable for 2 tripping or 1 + alarm) R2D 415 110-240-415V 2 earth leakage 2 operational threshold 5582.00 R4D 2 operational thresholds (configurable for 2 tripping or 1 + alarm) Flag indicator (TRIP MEMORY) Digital fault current measurement and display with configurable tripping value R4D 415 110-240-415V 2 earth leakage 2 operational threshold 8214.00 Toroidal current transformers for above earth leakage devices hole size RT60 60 mm toroidal transformer for above relays RT80 80 mm toroidal transformer for above relays 2307.00 RT110 110 mm toroidal transformer for above relays 2646.00 RT210 210 mm toroidal transformer for above relays 6269.00 RTA110 110 mm split-core toroidal transformers 6956.00 RTA210 210 mm split-core toroidal transformers 8261.00 RT... Earth leakage device incorporating toroidal transformer RC60 48 24-48Vac/dc 60 mm earth leakage and toroidal combinations 5243.00 RC60 415 110-240-415V 60 mm earth leakage and toroidal combinations 4228.00 RC80 415 110-240-415V 80 mm earth leakage and toroidal combinations 5745.00 RC110 415 110-240-415V 110 mm earth leakage and toroidal combinations 6026.00 RC80 415 B-43

Electronic earth leakage protection relays D30 Electronic relays with adjustable sensitivity and time delay - Sensitivity: adjustable from 0.03 A - 30 A - Trip time delay: adjustable from 0.02 s - 5 s Suitable for direct pulse current Immune to external disturbances DIN rail mounting sensitivity trip time delay Electronic earth leakage protection relays Slimline only 22.5mm wide (require external toroidal transformer) (H) 80 x (W) 22.5 x (D) 100 mm D30 0.03A - 30A 2.02-5 s electronic earth leakage relay 2755.00 Modular DIN rail mounting (H) 89 x (W) 52.5 x (D) 73 mm DM30 0.03A - 30A 2.02-5 s modular electronic earth leakage relay 2863.00 DR30A DR30A As above, but with automatic reclosing up to 3 attempts with adjustable (1 to 60 s) time 3289.00 Toroidal transformers for above earth leakage relays inner ø core CT1-1/35 35 mm closed torroidal transformer for earth leakage relays 574.00 CT1-1/60 60 mm closed torroidal transformer for earth leakage relays 757.00 CT1-1/80 80 mm closed torroidal transformer for earth leakage relays 960.00 CT1-1/110 110 mm closed torroidal transformer for earth leakage relays 1262.00 CT1-1/160 160 mm closed torroidal transformer for earth leakage relays 3538.00 CT1-1/110 CTA-1/110 110 mm split core torroidal transformer for earth leakage relays 5754.00 CTA-1/160 160 mm split core torroidal transformer for earth leakage relays 6480.00 CT1-1/35 B-44

Surge protection devices Modular plug-in surge protection devices SANS/IEC 61643-1 For the protection of low voltage equipment against transient voltages and current surges from atmospheric origins (lightning) as well as transients produced by switching characteristics such as in switching of distribution networks, transformers, motors, ect. PSC2-25/230 TT IR Provides protection for even most sensitive equipment (IEC 60634-4-443 category-1) Clear lifetime indication (on front face) and optional remote (IR) end of life signalling contact Meets all current international standards (IEC 61643 / IEC 62305, etc.) Plug-in cartridges for quick and easy replacement of damaged cartridges Suitable for all s of applications: residential, commercial and industrial Iimp L-N Imax L-N Uc Up L-N width in poles config. (ka) (ka) Volts (kv) 18 mm new PSC4-25/400 TT IR Class 1+2 Surge Protection Devices (combined in a single device) Suitable for first level of protection with incoming power supply panels and areas with greater exposure to lightning. For installations usually provided with external lightning protection systems. Capable of protecting equipment from direct lightning strikes High discharge capacity 10/350 μs: 12.5 ka or 25 ka per phase Provides protection for most sensitive equipment (IEC 60634-4-443 category 1) Iimp (10/350) 25 ka per phase, I total 50 ka (2 pole) and 100 ka (4 pole) PSC2-25/230 TT 25 ka 100 ka 275 V < 1.5 kv 2 1ph+N 4 4678.00 PSC2-25/230 TT IR 25 ka 100 ka 275 V < 1.5 kv 2 1ph+N 4 5099.00 PSC4-25/400 TT 25 ka 100 ka 275 V < 1.5 kv 4 3ph+N 8 10189.00 PSC4-25/400 TT IR 25 ka 100 ka 275 V < 1.5 kv 4 3ph+N 8 11105.00 Iimp (10/350) 12.5 ka per phase, I total 25 ka (2 pole) and 50 ka (4 pole) PSC2-12.5/230 TT 12.5 ka 65 ka 275 V < 1.3 kv 2 1ph+N 2 2900.00 PSC2-12.5/230 TT IR 12.5 ka 65 ka 275 V < 1.3 kv 2 1ph+N 2 3190.00 PSC4-12.5/400 TT 12.5 ka 65 ka 275 V < 1.3 kv 4 3ph+N 4 6382.00 PSC4-12.5/400 TT IR 12.5 ka 65 ka 275 V < 1.3 kv 4 3ph+N 4 7020.00 CSH1-50/230 Class 1 Surge Protection Devices (monoblock device) Monoblock device (does not accept replacement cartridges) CSH1-50/230 50 ka 50 ka < 2.0 kv 1 1ph 2 1771.00 CSH1-100N 100 ka 100 ka < 2.0 kv 1 N 2 2040.00 PSM1-40/230 PSM2-40/230 TT Class 2 Surge Protection Devices Suitable for second level of protection with distribution panels where 1 protectors are installed upstream or in areas not exposed to direct lightning strikes and with no external lightning protection High discharge capacity tested with an 8/20 μs waveform: 20kA or 40 ka per phase Provides protection for most sensitive equipment (IEC 60634-4-443 category 1) Imax 40 ka (8/20μs) PSM1-40/230 40 ka 275 V < 1.3 kv 1 1ph 1 526.00 PSM1-40N 40 ka 275 V < 1.3 kv 1 N 1 684.00 PSM2-40/230 TT 40 ka 275 V < 1.3 kv 2 1ph+N 2 1161.00 PSM2-40/230 TT IR 40 ka 275 V < 1.3 kv 2 1ph+N 2 1312.00 PSM4-40/400 TT 40 ka 275 V < 1.3 kv 4 3ph+N 4 2099.00 PSM4-40/400 TT IR 40 ka 275 V < 1.3 kv 4 3ph+N 4 2414.00 Imax 20 ka (8/20μs) PSM1-20/230 20 ka 320 V < 1.4 kv 1 1ph 1 451.00 PSM1-20N 20 ka 255 V < 1.4 kv 1 N 1 509.00 PSM2-20/230 TT 20 ka 320 V < 1.4 kv 2 1ph+N 2 921.00 PSM2-20/230 TT IR 20 ka 320 V < 1.4 kv 2 1ph+N 2 1041.00 PSM4-20/400 TT 20 ka 320 V < 1.4 kv 4 3ph+N 4 1728.00 PSM4-20/400 TT IR 20 ka 320 V < 1.4 kv 4 3ph+N 4 1987.00 With signalling contacts for remote indication/monitoring of devices PSM4-40/400 TT B-45

Surge protection devices PSM1-30/750 Iimp L-N Imax L-N Uc Up L-N (ka) (ka) Volts (kv) for surge protector Class 2 surge protection Devices for higher voltage applications (500-690V) Suitable for second level of protection with distribution panels where 1 protectors are installed upstream or in areas not exposed to direct lightning strikes and with no external lightning protection. Rated varistor voltage Uc = 750Vac / Imax 30kA (8/20μs) Un 690Vac Imax 30kA (8/20μs) PSM1-30/750 30 ka 750 V < 3.0 kv 1 1ph 1 691.00 PSM1-30/750 IR 30 ka 750 V < 3.0 kv 1 1ph 1 784.00 PSM3-30/750 TNC 30 ka 750 V < 1.3 kv 3 3ph 1 1982.00 PSM3-30/750 TNC IR 30 ka 750 V < 1.3 kv 3 3ph 1 2302.00 With signalling contacts for remote indication/monitoring of devices Surge protection for 600/1000 Vdc photovoltaic applications available on page G-4 PSM-40/230 Spare replacement plug-in cartridges for surge arrestors Class 1+2 PSC12.5/230 12.5 ka 65 ka 275 V < 1.3 kv PSC2/4-12.5 phase 1296.00 PSC 25/230 25 ka 100 ka 275 V < 1.5 kv PSC2/4-25 phase 2225.00 PSC 25N 25 ka 65 ka 255 V < 1.5 kv PSC2-12.5 neutral 1314.00 PSC 50N 50 ka 65 ka 255 V < 1.5 kv PSC4-12.5 neutral 2030.00 PSC 50N2 50 ka 65 ka 255 V < 1.5 kv PSC2-25 neutral 2030.00 PSC 100N 100 ka 100 ka 255 V < 1.5 kv PSC4-25 neutral 2900.00 Class 2 PSM-20/230 20 ka 320 V < 1.4 kv PSM1/2/4-20 phase 374.00 PSM-40/230 40 ka 275 V < 1.3 kv PSM1/2/4-40 phase 437.00 PSM-30/750 30 ka 750 V < 3.0 kv PSM1/3-30 phase 574.00 PSM-20N 20 ka 255 V < 1.5 kv PSM1/2/4-20 neutral 423.00 PSM-40N 40 ka 255 V < 1.5 kv PSM1/2/4-40 neutral 568.00 B-46

Overvoltage protection power frequency overvoltage (POP) Besides transient overvoltages, transmission lines can transmit a power frequency overvoltage above 10% of nominal for an indefinite period, caused by network problems, bad connections, damage/theft of the neutral conductor. Electrical distribution systems use the neutral conductor (usually grounded) as a reference for phase voltages, the return current through this conductor permits the voltage between each phase and neutral to remain constant, should the neutral conductor break, the line-to-neutral voltage is floating, and depending on the load imbalance, increases voltage causing premature ageing, excessive consumption with a resulting fire risk. surge protection device POP MCB general Imax L-N Up L-N Ua C curve break poles config. mod. (ka) (kv) (V) (In) capacity (18mm) V-CHECK - surge protection + POP + self reclose MCB in a single unit V-CHECK RPT Transient (surge) protection Power frequency Overvoltage Protection (POP) Overload and short circuit protection Self-reclose MCB (automatically resets once fault is cleared) V-CHECK 2MR-10 15 ka 1.5 kv >275 V 10A 6 ka 2 1ph+N 5 5181.00 V-CHECK 2MR-25 15 ka 1.5 kv >275 V 25A 6 ka 2 1ph+N 5 5181.00 V-CHECK 2MR-40 15 ka 1.5 kv >275 V 40A 6 ka 2 1ph+N 5 5788.00 V-CHECK 4MR-16 20 ka 1.5 kv >275 V 16A 10 ka 4 3ph+N 9 9653.00 V-CHECK 4MR-32 20 ka 1.5 kv >275 V 32A 10 ka 4 3ph+N 9 9750.00 V-CHECK 4MR-63 20 ka 1.5 kv >275 V 63A 10 ka 4 3ph+N 9 12525.00 Above also available without self-reclose facility V-CHECK RPT offers SPD+POP protection disconnecting the circuit via a circuit breaker shunt trip V-CHECK 4RPT 40 ka 1.8 kv >275 V 4 3ph+N 4 6963.00 V-CHECK RC offers SPD+POP protection disconnecting the circuit via a contactor V-CHECK 4RC 40 ka 1.8 kv >275 V 4 3ph+N 4 6963.00 OVERCHECK line monitoring unit protection against permanent overvoltages and short circuits OVERCHECK 2N-MT32 OVERCHECK is a programmable control unit and motorised circuit breaker which automatically disconnects the supply when voltage, current or earth leakage exceed preset threshold values, and re-connects the supply when these return to within their preset values. The OVERCHECK provides comprehensive protection of people and equipment connected to the grid, and its safe reconnection feature guarantees maximum service continuity. OVERCHECK 4N-MT63 Plug & play, supplied pre-wired automatic motorised circuit breaker, quick and simple to install Mini USB connection for quick and simple software updates Memory with historical fault log /programmable trip and delay thresholds / password protected End of cycle of reconnections after overload, short circuit or earth leakage / status indication Remote actuation: RST remote reset function / AUX external activation signal contacts Permanent under / over voltage, phase sequence protection (no earth leakage protection) OVERCHECK 2N-MT16 overcheck protection unit 16A 10 ka 2 1ph+N 9 9876.00 OVERCHECK 2N-MT32 overcheck protection unit 32A 10 ka 2 1ph+N 9 9976.00 OVERCHECK 2N-MT63 overcheck protection unit 63A 10 ka 2 1ph+N 9 10519.00 OVERCHECK 4N-MT16 overcheck protection unit 16A 10 ka 4 3ph+N 11 15372.00 OVERCHECK 4N-MT32 overcheck protection unit 32A 10 ka 4 3ph+N 11 15443.00 OVERCHECK 4N-MT63 overcheck protection unit 63A 10 ka 4 3ph+N 11 16811.00 Earth leakage, permanent under / over voltage and phase sequence protection OVERCHECK 2ND-MT16 overcheck protection unit 16A 10 ka 2 1ph+N 9 10677.00 OVERCHECK 2ND-MT32 overcheck protection unit 32A 10 ka 2 1ph+N 9 10785.00 OVERCHECK 2ND-MT63 overcheck protection unit 63A 10 ka 2 1ph+N 9 11321.00 OVERCHECK 4ND-MT16 overcheck protection unit 16A 10 ka 4 3ph+N 11 16810.00 OVERCHECK 4ND-MT32 overcheck protection unit 32A 10 ka 4 3ph+N 11 16881.00 OVERCHECK 4ND-MT63 overcheck protection unit 63A 10 ka 4 3ph+N 11 18250.00 TOCK-30 earth leakage protection transformer for above OVERCHECK... ND 936.00 G-CHECK continuous ground monitor Earthing monitor for continuous status checking, displays measured value of loop resistance in an installation. When a specified value is exceeded the G-CHECK triggers an alarm output. For TT, TNS and TNC-S systems. voltage frequency alarm activation value max. measured value G-CHECK 230 G-CHECK 230 230 V 50/60 Hz adjustable 500 ohms 7620.00 B-47

Surge protection devices 951110 For the protection of low voltage equipment against transient voltage and current surges mainly from atmospheric origin (lightning) and transient produced by switching characteristics such as in switching of distribution networks, transformers, motors, etc. limp L-N lmax L-N Uc Up width in poles config (ka) (ka) (V) (kv) 18 mm DEHNventil Class 1+2 surge protection devices (combined in a single unit) For installation in conformity with the lightning protection zone concept SANS 62305 at boundries O A - 2. Combined lightning current and surge arrester Replaceable plug-in modules Visual fault indication Clamps voltage to less than 1500V as per SANS 10142-1:2008 table L1 951110 25 ka 100 ka 255 V <1.5kV 2 1ph+N 4 10986.00 951115 25 ka 100 ka 255 V <1.5kV 2 1ph+N 4 11842.00 951310 25 ka 100 ka 255 V <1.5kV 4 3ph+N 8 20687.00 951315 25 ka 100 ka 255 V <1.5kV 4 3ph+N 8 22399.00 961180 Class 1 surge protection device with backup fuse 961200 25 ka 255 V <1.5kV 1 ph 2 5814.00 961205 25 ka 255 V <1.5kV 1 ph 2 6102.00 961180 25 ka 255 V <1.5kV 1 N 2 5609.00 961185 25 ka 255 V <1.5kV 1 N 2 5897.00 DEHNguard Class 2 surge protection devices Minimum requirement as per SANS 10142-1:2008 anex L for use in all electrical - distribution boards and sub boards. For installation in conformity with the lightning protection zone concept SANS 62305 at boundries O B - 2. 952070 952110 Replaceable plug-in modules Visual fault indication Clamps voltage to less than 1500V as per SANS 10142-1:2008 table L1 Imax 40kA (8/20μs) 952070 40 ka 275 V <1.25kV 1 ph 1 742.00 952090 40 ka 275 V <1.25kV 1 ph 1 999.00 952030 40 ka 275 V <1.5kV 1 N 1 1042.00 952035 40 ka 275 V <1.5kV 1 N 1 1815.00 952110 40 ka 275 V <1.25kV 2 1ph+N 2 1798.00 952115 40 ka 275 V <1.25kV 2 1ph+N 2 2041.00 952315 952310 40 ka 275 V <1.25kV 4 3ph+N 4 3681.00 952315 40 ka 275 V <1.25kV 4 3ph+N 4 4666.00 Class 2 surge protection device with backup fuse 952171 12 ka 25 ka 275 V <1.5 kv 2 1ph+N 2 3413.00 952176 12 ka 25 ka 275 V <1.5 kv 2 1ph+N 2 3659.00 952322 12 ka 25 ka 275 V <1.5 kv 4 3ph+N 4 5564.00 952327 12 ka 25 ka 275 V <1.5 kv 4 3ph+N 4 6135.00 With signalling contacts for remote indication/monitoring of devices For photovoltaic (PV) surge protection see page G-5 952322 B-48

Power supplies Power supplies CliQ series, from the worlds leading power supply manufacturer offers state-of-the-art designs made to withstand harsh industrial environments in accordance with ATEX requirements. The rugged ultra-compact case is both shock and vibration resistant according to IEC 60068-2. Certification: UL508, EN 60950, culus 60950, EN 50178, EN 60204, GS, CCS Aus DRP024V060W1AZ Product features: RoHS compliant Ease of wiring and handling Wide input voltage range 85 to 264Vac (1 phase) - 320 to 600Vac (3 phase) Provides - overload, overvoltage and thermal protection Power boost 150% for 3 secs (enables reserve power for reliable startup of loads with high inrush currents) Conformal coating on PCBA to protect against chemical and dust pollutants Hazardous locations approval to ATEX and Class I, Div 2 (for selected models) DIN rail mounting input output rated load dimensions (mm) housing voltage voltage (W) (A) (H) (W) (D) CliQ DIN rail mounting Universal AC input voltage without power de-rating Power Boost of 150% for 3 seconds (24V/480W: 200% for 2 seconds) Full corrosion resistant aluminium chassis Conforms to harmonic current IEC/EN 61000-3-2, Class A Operating temperature: -20 C to +80 C 12Vdc output DRP024V240W1AA DRP012V015W1AZ 85~264Vac 12Vdc (adj) 15 1.25 plastic 100 32 101 415.00 DRP012V030W1AZ 85~264Vac 12Vdc (adj) 30 2.5 plastic 100 32 101 460.00 DRP012V060W1AA 85~264Vac 12Vdc (adj) 60 5 aluminium 121 32 120 669.00 DRP012V100W1AA 85~264Vac 12Vdc (adj) 100 8.33 aluminium 121 50 119 1081.00 24Vdc output DRP-24V48W1AZ 85~264Vac 24Vdc (adj) 48 2 plastic 100 32 101 504.00 DRP024V060W1AZ 85~264Vac 24Vdc (adj) 60 2.5 plastic 121 32 113 573.00 DRP024V120W1AA 85~264Vac 24Vdc (adj) 120 5 aluminium 121 50 119 1094.00 DRP024V240W1AA 85~264Vac 24Vdc (adj) 240 10 aluminium 121 85 119 1706.00 DRP024V480W1AA 85~264Vac 24Vdc (adj) 480 20 aluminium 121 160 119 2814.00 CliQ II DIN rail mounting CliQ II DIN rail Power Supplies are high efficiency, high specification units featuring IP20 pluggable terminals and incorporated overvoltage, overload and over temperature protection on the output. DRP024V... Universal AC input voltage without power de-rating High efficiency > 90.0% @ 230Vac Power Boost of 150% for 5 seconds Full corrosion resistant aluminium chassis Conforms to harmonic current IEC/EN 61000-3-2, Class A Operating temperature: -25 C to +80 C 24Vdc output DRP024V060W1BN 85~264Vac 24Vdc (adj) 60 2.5 aluminium 121 32 125 948.00 DRP024V120W1BN 85~264Vac 24Vdc (adj) 120 5 aluminium 121 50 125 1372.00 DRP024V240W1BN 85~264Vac 24Vdc (adj) 240 10 aluminium 121 85 125 1945.00 DRP024V480W1BN 85~264Vac 24Vdc (adj) 480 20 aluminium 121 144 119 2998.00 48Vdc output DRP048V060W1BN 85~264Vac 48Vdc (adj) 60 1.3 aluminium 121 32 125 948.00 DRP048V120W1BN 85~264Vac 48Vdc (adj) 120 2.5 aluminium 121 50 125 1372.00 DRP048V240W1BN 85~264Vac 48Vdc (adj) 240 5 aluminium 121 85 125 1945.00 DRP048V480W1BN 85~264Vac 48Vdc (adj) 480 10 aluminium 121 144 119 2998.00 Three phase 320-600Vac - 24Vdc output DRP048V060W1BN DRP024V060W3BN 320~600Vac 24Vdc (adj) 60 2.5 aluminium 121 50 118 1467.00 DRP024V120W3BN 320~600Vac 24Vdc (adj) 120 5 aluminium 121 50 118 1615.00 DRP024V240W3BN 320~600Vac 24Vdc (adj) 240 10 aluminium 121 70 118 2218.00 DRP024V480W3BN 320~600Vac 24Vdc (adj) 480 20 aluminium 121 140 118 3151.00 DRP024V960W3BN 320~600Vac 24Vdc (adj) 960 40 aluminium 121 255 118 6237.00 B-49

Power supplies new DRC-24V10W1AZ Chrome DIN rail power supply is a compact, modular unit designed for compact cabinets, they feature a broad universal AC input range and are certified to international safety standards ITE and ICE. Compact modular housing (same profile and cut-out as standard MCB s) Class II double insulation (no earth connection required) Universal AC input voltage without power de-rating Conforms to harmonic current IEC/EN 61000-3-2, Class A Safety approval to IEC/EN/UL 60950-1 (ITE standard) and UL 508 (industrial standard) DIN rail mounting CHROME series input output rated load voltage voltage (W) (A) modular DIN rail mounting housing dimensions (mm) (H) (W) (D) 12Vdc output DRC-12V30W1AZ 90~264Vac 12Vdc (adj) 30 2.10 plastic 91 53 56 460.00 DRC-12V60W1AZ 90~264Vac 12Vdc (adj) 60 4.50 plastic 91 71 56 645.00 24Vdc output DRC-24V10W1AZ 90~264Vac 24Vdc (adj) 10 0.42 plastic 91 18 56 325.00 DRC-24V30W1AZ 90~264Vac 24Vdc (adj) 30 1.25 plastic 91 18 56 460.00 DRC-24V60W1AZ 90~264Vac 24Vdc (adj) 60 2.50 plastic 91 18 56 645.00 DRC-24V100W1AZ 90~264Vac 24Vdc (adj) 91.2 3.80 plastic 91 71 56 919.00 DRC-24V100W1AZ PMT-12V35W1AA PMT-12V50W1AA DRR-40N Panel mounting (chassis ) enclosed power supplies (single phase) PMT panel mount power supplies offer normal output voltages of 12V and 24V with a wide operating temperature range and can withstand shock and vibration according to IEC 60068-2, they offer overvoltage and over current protection. PMT meets price demand without compromising quality of components and product specifications. Universal AC input voltage without power de-rating (100/150W selectable by switch) Conforms to harmonic current IEC/EN 61000-3-2, Class A High MTBF > 700,000 hrs per Telcordia SR-332 Expected lifetime: 10 years 5Vdc output PMT-5V35W1AA 90~264Vac 5Vdc (adj) 35 7 aluminium 38 98 98 304.00 PMT-5V50W1AA 90~264Vac 5Vdc (adj) 50 10 aluminium 38 98 98 330.00 12Vdc output PMT-12V35W1AA 90~264Vac 12Vdc (adj) 35 2.92 aluminium 38 98 98 304.00 PMT-12V50W1AA 90~264Vac 12Vdc (adj) 50 4.17 aluminium 38 98 98 330.00 PMT-12V100W1AA 180~264Vac 12Vdc (adj) 100 8.50 aluminium 38 97 158 434.00 PMT-12V150W1AA 180~264Vac 12Vdc (adj) 150 12.5 aluminium 38 97 178 520.00 24Vdc output PMT-24V35W1AA 90~264Vac 24Vdc (adj) 35 1.46 aluminium 38 98 98 304.00 PMT-24V50W1AA 90~264Vac 24Vdc (adj) 50 2.10 aluminium 38 98 98 330.00 PMT-24V100W1AA 180~264Vac 24Vdc (adj) 100 4.50 aluminium 38 97 158 434.00 PMT-24V150W1AA 180~264Vac 24Vdc (adj) 150 6.50 aluminium 38 97 178 520.00 PMT-24V200W1AM 180~264Vac 24Vdc (adj) 200 8.80 aluminium 50 115 215 716.00 PMT-24V350W1AK 180~264Vac 24Vdc (adj) 350 14.60 aluminium 50 115 215 983.00 AC input voltage selectable via switch Complementary modules DIN rail mounting Conformal coating on PCBA to protect against chemical and dust pollutants Hazardous locations approval to ATEX and Class I, Div 2 Redundancy modules Wide input and output range of 22-60Vdc Built-in 2 channel DC OK signal and alarm contact DRR-20N redundancy module 20A aluminium 121 50 122 648.00 DRR-40N redundancy module 40A aluminium 121 50 122 798.00 Buffer module Minimum buffering time of 250ms @ 24V/20A Supports parallel connection for extended buffering time DRB-24V020ABN 250ms buffer module 20A aluminium 121 50 122 2645.00 DC-UPS module (without battery) Maximum output current up to 40A for 24V application High MTBF > 500,000 hrs per Telcordia SR-332 Built-in battery polarity protection circuit Built-in relay contacts DRU-24V40ABN DC-UPS module 40A aluminium 121 50 118 1147.00 B-50

Power supplies DIN rail mount power supplies Modular DIN rail mounting (aligns with standard MCB s with 45 mm cutout) Rated voltage 12Vdc or 24Vdc High efficiency up to 89% Adjustable output voltage input output rated load dimensions (mm) voltage voltage (A) (W) (H) (W) (D) PSL1M... Protection: short circuit overvoltage input voltage peaks Single-phase 100-240Vac (insulated housing) PSL1M02412 90-264Vac 12Vdc 2 24 96 36 56 544.00 PSL1M03312 90-264Vac 12Vdc 2.75 33 96 54 56 648.00 PSL1M05412 90-264Vac 12Vdc 4.5 54 96 72 56 752.00 PSL1M07212 90-264Vac 12Vdc 6 72 96 90 56 1026.00 PSL1... PSL1M02424 90-264Vac 24Vdc 1 24 96 36 56 544.00 PSL1M03624 90-264Vac 24Vdc 1.5 36 96 54 56 648.00 PSL1M06024 90-264Vac 24Vdc 2.5 60 96 72 56 752.00 PSL1M10024 90-264Vac 24Vdc 4.2 100 96 90 56 1026.00 DIN rail mounting (IEC/EN 60715) Rated voltage 24Vdc High efficiency up to 92% Adjustable output voltage PSL112024 90-264Vac 24Vdc 5 120 124 64 124 1244.00 PSL124024 90-264Vac 24Vdc 10 240 124 84 124 1917.00 PSL130024 90-264Vac 24Vdc 12,5 300 124 84 124 2332.00 Three phase (340-575Vac) PSL3... PSL312024 340-575Vac 24Vdc 5 120 124 74 119 1607.00 PSL324024 340-575Vac 24Vdc 10 240 124 89 119 2228.00 PSL348024 340-575Vac 24Vdc 20 480 124 150 119 3316.00 B-51

Control and safety transformers 680100040 TR28 Control and safety or isolating transformers Control and safety or isolating single-phase transformers supply high instantaneous power for the correct operation of contactors and other control and switchgear. DIN rail mountable (up to 400VA) High flexibility - several primary rated voltages (with regulation taps +20V or -20V) Serial-parallel secondary bridge pieces for ease of connection High capacity clamp terminals (10 mm 2 up to 400VA / 25mm 2 up to 1250VA) Primary voltages: 240V - 400V - 525V Secondary voltages: 12-24V (or) 115-230V (with regulation taps + and - 20V) Protection degree: IP20 protection (finger safe) Thermal class: B (130 C) Class: Class I Frequency: 50/60 Hz Dielectric strength: Primary - secondary > 4.5kV Standards: IEC/EN 61558-1, IEC/EN 61558-2-2 /-2-4 /-2-6 power (VA) inrush secondary dimensions (mm) weight t a 25 C t a 40 C VA voltage (H) (W) (D) kg TR 28 - secondary voltage: 12-24V Primary voltage: 240V - 400V - 525V 680040040 40 25 75 12-24V 113 84 96 1.17 678.00 680063040 63 40 120 12-24V 113 84 105 1.48 740.00 680100040 100 63 150 12-24V 113 84 112 1.83 773.00 680200040 200 160 350 12-24V 113 84 131 2.65 870.00 680320040 320 250 600 12-24V 135 108 138 4.45 1186.00 680400040 400 320 800 12-24V 135 108 148 5.00 1435.00 680320042 680630040 630 500 1275 12-24V 152 120 156 7.08 1831.00 680800040 800 630 1700 12-24V 177 150 140 8.68 2329.00 681000040 1000 800 2100 12-24V 177 150 160 11.50 2561.00 681250040 1250 1000 3300 12-24V 177 150 183 14.40 3352.00 TR 28 - secondary voltage: 115-230V - Primary voltage: 240V - 400V - 525V 680040042 40 25 75 115-230V 113 84 96 1.17 678.00 680063042 63 40 120 115-230V 113 84 105 1.48 740.00 680100042 100 63 150 115-230V 113 84 112 1.83 773.00 680200042 200 160 350 115-230V 113 84 131 2.65 870.00 680320042 320 250 600 115-230V 135 108 138 4.45 1186.00 680400042 400 320 800 115-230V 135 108 148 5.00 1435.00 680630042 630 500 1275 115-230V 152 120 156 7.08 1831.00 680630042 680800042 800 630 1700 115-230V 177 150 140 8.68 2329.00 681000042 1000 800 2100 115-230V 177 150 160 11.50 2561.00 681250042 1250 1000 3300 115-230V 177 150 183 14.40 3352.00 B-52