INSTALLATION INSTRUCTIONS

Similar documents
INSTALLATION INSTRUCTIONS

riderite.com INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS

WARNING: HARDWARE PACK (A ) DO NOT INSTALL if the truck has been lifted and the stock jounce bumper spacers are not on the vehicle.

WARNING: INSTALLATION INSTRUCTIONS IMPORTANT! PARTS LIST

Suspension Leveling Kits HIGH LOW REGULAR. .f. KT ASSEMBLY AND USAGE GUIDE

Part# JL AIR IT UP 4 Tire On Board Air Delivery System. (Requires External Air Source)

NOTE: PARTS LIST. system to provide equal pressure to both air springs,

THIS KIT DOES NOT REQUIRE DRILLING INTO THE FRAME.

Kit No Please read these instructions completely before proceeding with installation. Air Spring Kit Parts List. Bracket Attaching Hardware

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS

Installation Instructions READ INSTALLATION INSTRUCTIONS IN ITS ENTIRETY BEFORE INSTALLING YOUR COIL-RITE KIT

INSTALLATION INSTRUCTIONS

Kit No Please read these instructions completely before proceeding with installation. Parts List G J I K L H CC FF DD MN-505 (01201) NPR 3733

Frame. Axle. Kit No Please read these instructions completely before proceeding with installation. Figure 1. Kit Parts List FORWARD B J

Please read these instructions completely before proceeding with installation. Read all maintenance guidelines on page 7 before operating the vehicle.

69-74 VW Beetle IRS Rear Kit Part No

TOOLS REQUIRED UTILITY KNIFE 21MM END WRENCH

WARNING: INSTALLATION INSTRUCTIONS IMPORTANT! PARTS LIST

WARNING: INSTALLATION INSTRUCTIONS IMPORTANT! PARTS LIST

INSTALLATION INSTRUCTIONS IMPORTANT! PARTS LIST WARNING:

I. Assembling the Air Spring

WARNING: Installation of this kit requires a minimum of 7-1/2" of clearance between the tire side wall and the frame. INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS

WARNING OPERATING PRESSURES: READ INSTALLATION INSTRUCTIONS COMPLETELY BEFORE INSTALLING YOUR KIT

2458 / 2459 / 2461 WARNING: INSTALLATION INSTRUCTIONS IMPORTANT! PARTS LIST

4X4 ONLY WARNING: DO NOT INSTALL if the truck has been lifted and the stock jounce bumper spacers are not on the vehicle.

82-01 Chevy S-10/ GMC Sonoma Front Kit Part No B

INSTALLATION INSTRUCTIONS Part# , , ,

WARNING: Installation of this kit requires a minimum of 7-1/2" of clearance between the tire side wall and the frame. INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS

TO BE USED ON A CAB AND CHASSIS TRUCK ONLY. DO NOT USE ON A PICKUP TRUCK.

INSTALLATION INSTRUCTIONS IMPORTANT! PARTS LIST WARNING:

WARNING: INSTALLATION INSTRUCTIONS IMPORTANT! PARTS LIST

INSTALLATION INSTRUCTIONS IMPORTANT! PARTS LIST WARNING:

Kit No Please read these instructions completely before proceeding with installation. Air Spring Kit Parts List. Attaching Hardware

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS

4101 / 4102 READ INSTALLATION INSTRUCTIONS IN ITS ENTIRETY BEFORE INSTALLING YOUR COIL-RITE KIT PARTS LIST OPERATING PRESSURES. Figure A DESCRIPTION

WARNING! INSTALLATION INSTRUCTIONS IMPORTANT! PARTS LIST

WARNING! INSTALLATION INSTRUCTIONS IMPORTANT! PARTS LIST

BOLT PACK (A ) M10 LOCK WASHER 2 DISK /8"-16 X 1-1/2" HEX BOLTS 8 BRACKET STRAPS

PRODUCT SAFETY NOTICE

WARNING! PARTS LIST 01-13

Kit No Please read these instructions completely before proceeding with installation. Air Spring Kit Parts List. Bracket Attaching Hardware

WARNING: INSTALLATION INSTRUCTIONS IMPORTANT! PARS LIST

WARNING: INSTALLATION INSTRUCTIONS IMPORTANT! PARTS LIST

Tools Needed. I. Getting Started

Kit No Please read these instructions completely before proceeding with installation. Figure 1. Forward. Passenger-Side View

R4TECH PRODUCT SAFETY NOTICE

DR W

PRODUCT SAFETY NOTICE DEALER/INSTALLER NOTICE

OPERATING INSTRUCTIONS AND TROUBLE SHOOTING GUIDE

FIGURE 2 FIGURE Remove the rubber jounce bumper. This will not be reused.

INSTALLATION INSTRUCTIONS Air Spring Kit Dodge WD IMPORTANT NOTES

Heavy Duty Air Command

HP10207 KIT. Ram WD*

OPERATING INSTRUCTIONS AND TROUBLE SHOOTING GUIDE

Kit No (THIS KIT IS FOR A 2" AND 4" DROP)

Driver Side Shown P/N Figure 1

Kit Chevrolet/GMC Heavy Duty. Installation Guide

INSTALLATION INSTRUCTIONS

HP10220 KIT. See application guide for proper fitment.

HP10033 KIT. * See application guide for proper fitment.

INSTALLATION INSTRUCTIONS Air Spring Kit Dodge 2500 with Rear Coil Springs IMPORTANT NOTES

Representative vehicle image

AIR CONTROL ACCESSORY KIT

C-4500 Kit No The Choice of the Professional Installer

Please read these instructions completely before proceeding with the installation.

KIT No , and 80590

HP10019 KIT. Universal AMP Air Suspension Kit

INSTALLATION INSTRUCTIONS Air Spring Kit Ford F-250/350 Single Wheel 2WD IMPORTANT NOTES

Kit INSTALLATION GUIDE. Honda Odyssey, Honda Pilot, & Acura MDX

Kit No Please read these instructions completely before proceeding with installation. Figure 1 MN-614 (06601) ECR

Light Duty Electronic Air Command

Please read these instructions completely before proceeding with the installation. Press Lock Swivel Elbow Fitting. Air Sleeve.

Kits Installation Guide. Dodge/RAM WD and 4WD

INSTALLATION INSTRUCTIONS Air Spring Kit IMPORTANT NOTES

Ford Ranger Rear Kit Part No

Kits Installation Guide current Chevrolet Silverado HD and GMC Sierra HD. Watch the video Info on next page

Kit INSTALLATION GUIDE. Ford F-150

FIGURE 2 FIGURE 3 FIGURE 4

P/N 59511, NEVER EXCEED THE MANUFACTURERS MAXIMUM GROSS VEHICLE WEIGHT RATING. DO NOT INSTALL THE AIR SPRING AS THE PRIMARY SUSPENSION SPRING.

AIR SUSPENSION KIT HP UNIVERSAL AIR SUSPENSION KIT

Kit Dodge Ram 2500HD

The purpose of this publication is to assist with the installation, maintenance and troubleshooting of the Air Lift 1000 air spring kit.

Kit No (THIS KIT IS FOR A 2" AND 4" DROP)

LoadLIFTER. Kit Chevrolet Silverado/ GMC Sierra 3500 Commercial Cab and Chassis INSTALLATION GUIDE

FIGURE 2 FIGURE 3 AFTER BEFORE

Transcription:

2705 INSTALLATION INSTRUCTIONS 5-6

! IMPORTANT PLEASE DON T HURT YOURSELF, YOUR KIT OR YOUR VEHICLE. TAKE A MINUTE TO READ THIS IMPORTANT INFORMATION. This kit is to be used on a pickup truck only, and DOES NOT INCREASE YOUR VEHICLE S MAXIMUM LOAD. SAFE INSTALLATION Please take all safety precautions during installation. A hydraulic jack can fail, and if that happens, you can be seriously hurt, or worse, if you are relying on it to hold up the vehicle. If you use a hydraulic jack, secure jack stands in the appropriate locations and chock any tires still touching the ground. Wear safety glasses or goggles. Your eyes may be lower than some parts and pieces, and you don t want to lose an eye. Remove the possibility of any electrical issues by disconnecting the negative battery cable. KIT CLEARANCE There must be a minimum of /2 clearance around all installed components when the Air Springs are inflated and under a load. The Air Springs must flex and expand during operation, so the clearance keeps the kit from rubbing against parts of the vehicle. VEHICLE GVWR NEVER exceed the maximum load recommended by the vehicle manufacturer (GVWR). The GVWR can be found in your vehicle s owner s manual or on the data plate on the driver s side door. Consult your local dealership for additional GVWR specifications. INFLATING THE AIR SPRINGS When inflating Air Springs, add air pressure in small quantities, checking air pressure frequently. The Air Springs have much less air volume than a tire, so they inflate much more quickly. PRESSURE TO LOAD The Air Springs will support approximately 50 lbs. of load for each PSI of inflation pressure (per pair). For example, 50 PSI of inflation pressure will support a load of 2500 lbs. per pair of Air Springs. APPROPRIATE AIR PRESSURE For best ride, use only enough air pressure in the Air Springs to level the vehicle when viewed from the side (front to rear). This will vary, depending on the load, location of the load, condition of the existing suspension, and personal preference. NYLOCK NUTS Using an impact gun is NOT recommended when fastening Nylock Nuts. Doing so may result in the nylon insert overheating, causing it to loosen over time. OPTIONAL T-FITTING This kit includes Inflation Valves and Air Line Tube for each Air Spring, allowing you to compensate for unbalanced loads. If you prefer a single Inflation Valve system to provide equal pressure to both Air Springs, your dealer can supply the optional T fitting (Part # 3025 or WRI-760-346 retail pack). ONCE INSTALLED SUCCESSFULLY, FOLLOW THESE PRESSURE REQUIREMENTS FOR THE AIR SPRINGS:

PARTS Compare the parts below to your kit. Assure you have all pieces, and organize them for an easier installation. MAIN KIT CONTENTS PART # 840 AIR SPRING PART # 584 LOWER BRACKET PART # 3292 BAIL CLAMP PART # 5823 UPPER BRACKET PART # 58 AXLE STRAP BRACKET PART # 004 x HEAT SHIELD PART # 953 x AIR LINE TUBE (30 FEET) A24-760-7560 INFLATION VALVE BRACKET KIT PART # 9483 x NO-DRILL INFLATION VALVE BRACKET PART # 9488 LARGE NYLON TIE A2-760-2705 HARDWARE PACK PT # 3490 3/8" - 6 x 3/4" FLANGE BOLT PT # 3488 x 4 3/8" - 6 NYLOCK NUT PT # 3293 x 4 M0 -.50 x 30mm FLAT HEAD BOLT PT # 3064 3/4" INTERNAL TOOTH LOCK WASHER PT # 3485 3/4" - 6 HEX NUT PT # 303 ELBOW AIR FITTING PT # 3032 INFLATION VALVE AND VALVE CAP ASSEMBLY PT # 3033 x 4 5/6" FLAT WASHER PT # 968 x 6 BLACK NYLON TIE PT # 3493 x 4 3/8 FLAT WASHER (Use as necessary with 3/8 Nylock Nuts) PT # 0899 THERMAL SLEEVE 2705 Installation Instructions 2

CONTENTS AND OVERVIEW 4 5 REMOVE JOUNCE BUMPER & SELECT LOWER BRACKET ORIENTATION FASTEN AIR SPRING TO LOWER BRACKET Vehicle front 6 7 INSTALL UPPER BRACKET AIR SPRING ASSEMBLY INSTALLATION ELBOW AIR FITTING 3/4"- 6 HEX NUT 3/4" INTERNAL TOOTH LOCK WASHER 8 AXLE STRAP BRACKET INSTALLATION UPPER BRACKET 9 0 HEAT SHIELD & PASSENGER SIDE AIR LINE TUBE & INFLATION VALVE INSTALLATION INSTALL & ROUTE AIR LINE TUBE M0 -.50 x 30mm FLAT HEAD BOLT BAIL CLAMP ALIGNMENT PIN *See important note - Step 5. AIR SPRING NOTE: See page 7 for important installation positioning. 2 CHECKING THE SYSTEM 3 4 FIXING AN AIR LEAK FINISHING THE INSTALLATION LEAF SPRINGS LOWER BRACKET NOTE: See page 4 on installation positioning. AXLE 3/8" - 6 x 3/4" FLANGE BOLT AXLE STRAP BRACKET 3/8"- 6 NYLOCK NUT Fasten to Bail Clamp. 3

REMOVE EXISTING JOUNCE BUMPER START THE INSTALLATION ON THE LEFT SIDE OF THE VEHICLE WHEN FACING FORWARD. VEHICLE FRAME Unfasten and remove existing jounce bumper from the vehicle. JOUNCE BUMPER DETERMINE LOWER BRACKET ORIENTATION 2 THE ORIENTATION OF THE BRACKET IS IMPORTANT. NOTE THE DIFFERENCE AND USE THE CORRECT SIDE FOR YOUR VEHICLE. LOWER BRACKET ORIENTATION GASOLINE ENGINE DIESEL GASOLINE LEAF SPRINGS LEAF SPRINGS AXLE U-BOLTS DIESEL ENGINE WIDE SIDE AIR SPRING MOUNTING HOLE NARROW SIDE 2705 Installation Instructions 4

3 FASTEN AIR SPRING TO LOWER BRACKET Install the Air Spring to the Lower Bracket, as shown. 2 Do not fully tighten the fastener at this stage. AIR SPRING LOWER BRACKET Use orientation determined in Step 2. 3/8" - 6 x 3/4" FLANGE BOLT DO NOT FULLY TIGHTEN THE BOLT AT THIS STAGE. TORQUE TO SPEC IN STEP 5. 5

INSTALL THE UPPER BRACKET 4 Vehicle front Fasten the Upper Bracket using existing jounce bumper bolt hole locations on vehicle. UPPER BRACKET M0 -.50 x 30mm FLAT HEAD BOLT MAKE SURE THE UPPER BRACKET ASSEMBLY IS FASTENED TIGHTLY TO THE VEHICLE FRAME. 2705 Installation Instructions 6

5 INSTALL AIR SPRING ASSEMBLY INSTALLING THE RIGHT SIDE? REMEMBER STEP 7 FIRST! Follow guidelines below to dry fit assembly. Make alignment marks as shown. 2 Remove assembly and match alignment marks you made. 3 Fully tighten Flange Bolt to fasten the Air Spring to the Lower Bracket. 4 Install assembly and follow the guidelines. Vehicle front ELBOW AIR FITTING Tighten until threadlock coating is fully engaged. 3/4"- 6 HEX NUT Thread onto outside of Air Combo Stud. 3/4" INTERNAL TOOTH LOCK WASHER VIEW FROM BELOW ROTATE AIR SPRING ASSEMBLY TO USE FRONT OR BACK COMBO STUD AND ALIGNMENT HOLES FOR BEST VERTICAL ALIGNMENT. ALIGNMENT PIN ON AIR SPRINGS MUST BE INSTALLED TO FULLY SEAT INTO ONE OF THE ALIGNMENT HOLES IN THE UPPER BRACKET. FAILURE TO DO SO WILL CAUSE IT TO BE PUSHED INTO THE BEAD PLATE, CREATING AN AIR LEAK, AND RESULTING IN AN AIR SPRING FAILURE THAT IS NOT WARRANTABLE. THE ALIGNMENT PIN CANNOT HOLD 2,500 LBS! IT IS USED FOR ALIGNMENT ONLY! UPPER BRACKET AIR COMBO STUD ALIGNMENT PIN Must fully seat into alignment hole selected above. MAKE ALIGNMENT MARKS 3/8" - 6 x 3/4" FLANGE BOLT Match alignment marks. 7

INSTALL AXLE STRAP BRACKET 6 Vehicle front Assure that the Lower Bracket is tight against the leaf spring stack on the vehicle. 2 Install 3 Alternate the Bail Clamp over the Lower Bracket, assuring that the Bail Clamp is positioned into the Lower Bracket notches, as shown. tightening of the 3/8"-6 Flange Nuts to draw Axle Strap Bracket evenly around the axle. BAIL CLAMP LEAF SPRINGS BAIL CLAMP INSTALLED AXLE Vehicle front AXLE STRAP BRACKET 3/8" - 6 NYLOCK NUT Alternate tightening to draw Axle Strap Bracket evenly to the axle. 3/8" - 6 NYLOCK NUT USE YOUR HAND TO CHECK FOR THE PROPER CLEARANCE AROUND THE AIR SPRING. IF YOUR HAND DOES NOT FIT BETWEEN THE AIR SPRING AND OTHER COMPONENTS, IT WILL RUB! BAIL CLAMP AXLE STRAP BRACKET 3/8" - 6 NYLOCK NUT 2705 Installation Instructions 8

7 INSTALL RIGHT SIDE WITH HEAT SHIELD AWESOME! You re done with the left side. The right side installation is the same, with the addition of this step. Go complete Steps -4 for the right side, then complete this step before continuing to Step 5. RIGHT SIDE INSTALLATION MUST INCLUDE HEAT SHIELD! HEAT SHIELD AIR SPRING HEAT SHIELD Position Heat Shield to closest point of exhaust. DO NOT PLACE DIRECTLY ABOVE AXLE. 9

INSTALL INFLATION VALVES 8 x 4 IF USING THE OPTIONAL NO-DRILL INFLATION VALVE BRACKET, CHOOSE OPTION. IF DRILLING, CHOOSE OPTION 2. INFLATION VALVES MUST BE ACCESSIBLE BY AN AIR CHUCK. Secure the Air Inflation Valve Bracket to a protected, secure location. PROCEED TO STEP 3. 2 Select a protected location to install the Inflation Valves, such as the bumper or the body of the vehicle. 3 Install Inflation Valve assembly as shown. LARGE NYLON TIES Drill two 5/6" holes for Inflation Valve install locations. AIR LINE TUBE 5/6-6 FLAT WASHER EXAMPLE 5/6 INFLATION VALVE INFLATION VALVE NUT Inflation Valve install locations. BUMPER INFLATION VALVES Vehicle body, bumper or Inflation Valve Bracket. VALVE CAP CUT THE AIR LINE TUBE INTO TWO EQUAL LENGTHS 9 Match Air Line Tube ends. AIR LINE TUBE 2 Find center of Air Line Tube, make a square cut with tube cutter or sharp utility knife. DO Make sure the cut is as square as possible. Use a tube cutter or sharp utility knife. DON T Fold or kink the Air Line Tube. Cut the Air Line Tube at an angle. Use pliers, scissors, snips, saws, or side cutters. PROPER AND IMPROPER CUTS IN THE AIR LINE TUBE Square cut AIR LINE TUBE AIR LINE TUBE AIR LINE TUBE AIR LINE TUBE 90 2705 Installation Instructions 0

0 INSTALLING AIR LINE TUBE INTO AIR FITTINGS AND INFLATION VALVE Insert end of Air Line Tube into Air Fitting. 2 Push Air Line Tube into Air Fitting as far as possible. 3 Gently pull on the Air Line Tube to check for a secure fit. 4 To remove, push down collar and gently pull Air Line Tube away. Removal Tip: Use a /4ʺ, 5/6ʺ, or 6mm open-ended wrench to push the collar down. ROUTE AND SECURE AIR LINE TUBES Air Line Tube routes will vary, depending on your truck, and requires you to choose the best path from the Air Springs to the Inflation Valves. Use the instructions below to help you choose. x 7 DO Select routes protected from heat, debris, and sharp edges. Use Thermal Shields near heat sources. Use Nylon Ties to secure the Air Line Tube. DON T Bend or sharply curve Air Line Tubes. Leave Air Line Tube exposed to sharp edges. Use unnecessary lengths of Air Line Tube. Route Air Line Tube near moving parts. Let Air Line tube hang unsecured from vehicle. Scar Air Line Tube while routing. AIR LINE TUBE THERMAL SHIELD INFLATION VALVE USE SUPPLIED THERMAL SHIELDS WHEN AIR LINE TUBE RUNS WITHIN 6 INCHES OF HEAT SOURCES. AIR FITTING AIR LINE TUBE

CHECKING THE AIR SYSTEM 2 Place an air chuck onto the Inflation Valve and fill the system to 70 PSI. 2 Spray fittings with soap and water mixture. 70 PSI AIR SPRINGS INFLATE QUICKLY. CHECK AIR PRESSURE WHILE INFLATING. WATER + SOAP 3 Observe bubbles. SMALL SOAP BUBBLES THAT DO NOT EXPAND SOAP BUBBLES THAT EXPAND NO LEAKS? Congratulations! Continue to Step 4 to finish installation. Review the Operating Instructions. LEAK? Bummer. Continue to Step 3 to fix the leak. 2705 Installation Instructions 2

3 FIXING AN AIR LEAK Press the air valve on end of Inflation Valve to release all air pressure. 0 PSI AIR VALVE EXHAUST ALL AIR FROM THE SYSTEM PRIOR TO RELEASING AIR LINE TUBES FROM AIR FITTINGS. LEAK AT AIR LINE TUBE AND AIR FITTING LEAK AT BASE OF AIR FITTING ON AIR SPRING LEAK OUT OF THE VALVE CORE ON INFLATION VALVE Release Air Line Tube (see page ). Review proper cuts and procedures in Step 9. Repeat Steps 0 and 2. Tighten Air Fitting one turn or until leak stops. Tighten valve core with valve core wrench on Inflation Valve Cap. STILL HAVE A LEAK? Refer to the Troubleshooting section of the Instruction Manual. If the leak persists, or if there is an issue with a leaking part, call -800-888-0650; Option ; Option for Tech Support. 3

FINISHING THE INSTALLATION 4 SAFELY RETURN VEHICLE TO OPERATIVE STATE If you removed any wheels during installation, install the wheels and torque the lug nuts to the manufacturer s specifications. Safely remove any jack stands and wheel chocks used during installation. Re-attach the negative battery cable. DOUBLE-CHECK AIR SPRING CLEARANCE Check the Air Springs once again for the proper /2" minimum clearance. Perform clearance check again when vehicle is under load. USE YOUR HAND TO CHECK FOR THE PROPER CLEARANCE AROUND THE AIR SPRING. IF YOUR HAND DOES NOT FIT BETWEEN THE AIR SPRING AND OTHER COMPONENTS, IT WILL RUB! VEHICLE GVWR NEVER exceed the maximum load recommended by the vehicle manufacturer (GVWR). The GVWR can be found in your vehicle s owner s manual or on the data plate on the driver s side door. Consult your local dealership for additional GVWR specifications. READ AND UNDERSTAND THE OPERATING INSTRUCTIONS The Ride-Rite system can improve handling and comfort. Take the time to learn how to properly use and maintain your investement by reading the Operating Instructions. /2" /2"! IMPORTANT A MINIMUM OF 5 PSI MUST BE MAINTAINED IN THE AIR SPRINGS AT ALL TIMES Too much air pressure in the Air Springs will result in a firmer ride, while too little air pressure will allow the Air Springs to bottom out over rough conditions, and will not provide the improvement in handling that is possible. 2705 Installation Instructions 4

2705 BEFORE YOU DRIVE, CONFIRM THE FOLLOWING: Do you have a minimum of 5PSI in your Air Springs? Are your Air Springs standing 5 /2" - 7" tall? Are your Air Springs properly aligned, left-to-right and front-to-back? Are your nuts and bolts tight? 5 /2" - 7" Put your paper work back into the sleeve and keep it in your glove compartment for future reference. You ve been bagged and now your suspension is Airide equipped! Show it off with the supplied decal! NEED INSTALLATION HELP? -800-888-0650 Select Option for Ride-Rite; Select Option for Technical Support. Or, email us at rrtech@fsip.com. If emailing, please include photos to help us better diagnose and understand any problems you may be experiencing. CONNECT WITH US @rideriteair @rideriteair Firestone RideRite Firestone Ride-Rite 5-6