For Malaria extermination SPRAYCAN HANSEN ML - 12 HOW TO FIT THE SPRAYER UP Tank and Pump assembly is already installed in one assembly of HANSEN Spraycan. You only have to assemble the spraying component simply by to connect and then fastened up in consecutively as follow : - Nozzle to the upper side of lance - The bottom side of Lance to the trigger grip of stop valve with it s spray hose. - The end edge of spray hose to the shut off cock at the top side of Tank
SPRAYCAN FOR Malaria Extermination ML - 12 1. General Information 2. Check List for contents of sprayer box 3. Assembly 4. Filling 5. Spraying 6. Safety 7. Maintenance and care 8. Storage 9. Technical specification SPARE PARTS LIST : ML - 12 PART NO PART CODE PART NAME 1 NK Flood jet nozzle Nozzle kipas 2 H-5 Lance ( Spraying Pipe ) Pipa Penyemprot 50 cm 3 014-48 Joint s Gasket Packing Gabungan 4 H-7 Pistol Grip Stop Valve Kran Pencet 5 H-10 Spraying Hose Selang + Pegangan 150 cm 6 H-16 Discharge Pipe Gasket Packing Kepala Pipa Air 7 H-70 Pressure Gauge Manometer 8 H-59 Filler Cap Tutup Tanki 9 H-69 Filler Cap Chain Hold Rantai 10 H-26 Spraycan Tank Badan Tanki 11 H-54 Pump Lever Plug Tutup Gagang Piston 12 H-52 Piston Rod ( Plunger ) Batang Piston 13 H-44 Leather Cap Gasket Klep Kulit 14 H-45 Leather Cap Retainer Dudukan Klep 15 H-41 Cylinder s Ring Gasket Packing Tutup Atas Silinder 16 H-39 Cylinder Silinder 17 H-33 Cylinder Valve Housing Mur Bawah Silinder 18 H-34 Cylinder Valve Spring Per 19 H-35 Cylinder s Valve Plunger Piston Bawah Silinder 20 H-36 Cylinder s Valve s Gasket Packing Piston Bawah Silinder 21 H-24 Hanging Straps Tali Gendong
Congratulations on the purchase of you new HANSEN Sprayer. We would like to thank you for choosing our product, and we are sure that you will be very happy with it. 1. General Information : The HANSEN Spraycan is a hand sprayer which be designer for spray wark in human residental in order to kill anopheles mosquito the malaria disease propagator and the like, by killing anopheles mosquitoes it also exterminate the Malaria disease All accident prevention regulations and all generally recognized safety precautions are to be followed. Any unauthorized modifications or changes made to the pressure sprayer will automaticallly exclude liatbility claims against the manufacturer 2. Check list for contents of sprayer box : 1 Tank assembly 1 Pump assembly 1 Spraying component consist of : hose, trigger grip stop valve, lance and cozzle 1 Sealed plastic bag of spare parts 1 Instruction manual 1 Chum 3. Assembly : Tank and Pump assembyl is already installer in one assembly of HANSEN Spraycan. You only have to assemble the spraying component simply by to connect and then fastened up in consecutively as follow : - Nozzle to the upper side of Lance. - The bottom side of Lance to the trigger grip of stop valve with it s spray hose. - The end edge of spray hose to the Shut off cock at the top side of tank.
4. Filling When filling the ML-12 tank always use the filter provided with the machine. A v o i d a d i r e c t c o n n e c t i o n b e t w e e n w a t e r h o s e a n d s p r a y t a n k avoid any overflow from the tank and any contamination of public water and drainage. 5. Preparing Spray solution and Filling Dilute in other container the correct chemical with clean pure water in a proper Measurement according to the kind of disease propagator insects which will be killed. Stir it up thoroughly, then pour the solution into the tank of HANSEN Spraycan through the filler hole using Churn. Fill the thank up to the three quarter of the tank capacity volume only. The one quarter is used to accumulate air pressure inside tank over the solution surface. 6. Safety Do not operate the sprayer while persons or animal are in close contact. Never smoke, drink or eat whilw you are spraying. After you finish spraying. Clean and flush the sprayer tank as well as all parts which come contact with chemicals. Residues of plant protection chemicals may lead to corrosion and damage of the sprayer. 9. Technical Specification : Tank Capacity : 3 US Gallons ( 11,3 Litres ) Pump type : Air Compressing Hand Pump. Material Used : Stainless Steel Sheet AISI-304-BA Spray Lance : Stainless Steel pipe Spraycan Measurement : Heigh : 445 mm Tank diameter : 190 mm Empty weight : 5.5 kgs 7. Maintenance and care : The ML-12 Sprayer is almost maintenance free. After every spraying job, clean the sprayer with sprayer by washing the inside of the tank with pure clean water at least twice. To wash up the inner side of the hose. Lance and nozzle, add 3 liters of pure clean water into the clean tank, then spray it out by pumping movement until all the water will be sprayed out through the nozzle tip 8. Storage Never store the M-12 Sprayer with chemicals inside the tank. Spray the chemical out all or keep them in other container to be used next time. We recommended that the unit will be protected from direct sunlight and store in a dryroom, away from children and animals.