data features 22 ton ( mton) capacity 4-section, 1' (, m) proportional booms 1' "(33,7 m) maximum main boom tip height 139' " (42,6 m) maximum tip height with jib 2' (,5 m) fixed jib 2-speed planetary hoist with grooved drum Anti-two-block system Load Moment Indicator (LMI) senses boom hoist cylinder pressure, boom length and boom angle Adjustable Out-and-Down outriggers from 7' 4.3"(2,2 m) to 19' 9.5" (6,0 m) wide System pressure gauge Rugged, weatherproof, automotive style electrical system Manitowoc CraneCARESM comprehensive support product guide contents Specifications Outline Dimensions 221S Single Axle Fully Extended Boom/Jib Range Diagram 221S Dual Axle Fully Extended Boom/Jib Range Diagram 221S Dual AxleFully Extended Boom/Jib Load Charts 221S Dual Axle Intermediate Boom/Jib Range Diagram 221S Dual Axle Intermediate Boom/Jib Load Charts 221S Dual Axle Fully Retracted Boom/Jib Range Diagram 221S Dual Axle Fully Retracted Boom/Jib Load Charts Load Chart Data CraneCARE SM 2 4 6 7 9 11 13
specifications 2 Upperworks Boom Boom Inverted T-cross section. 4-section telescoping type, extended and retracted proportionally by double-acting hydraulic cylinder and cable-crowd system. Easily replaceable and adjustable high-density nylon slide pads. 221S 4-Section ' 5" (9,0 m) to 1' (, m). Maximum tip height 1' " (33,7 m). 1-section, ' (9,1 m) fixed jib. Maximum tip height 139' " (42,6 m). Quick Reeve Boom Point Three high-density nylon sheaves mounted on heavy-duty roller bearings. Two removable pin-type rope guards. Boom Elevation Double-acting hydraulic cylinder. Working range from 9.5 below horizontal to 0.5 above. Hoist Hoist Theoretical maximum line speed 247 fpm (75,3 mpm). Maximum theoretical bottomlayer line pull,000 (5 443 kg). Two-speed planetary reducer. Spring-applied, pressure-released internal brake. Wire Rope 0 feet (91,4 m) of 9/16" (,3 mm) 6x25 EIPS IWRC wire rope. Swing System Externally mounted, double-reduction planetary driven by hydraulic motor. Maximum swing speed 1.5 rpm. Spring-applied hydraulically released parking brake. Balearing swing circle with external gear. Continuous rotation is standard. Outriggers Out-and-Down type with double-acting hydraulic cylinders operated independently from rear for precise leveling (221S Dual Axle offers fully extended, intermediate extension and fully retracted positions). Bubble level located near outrigger controls. Mounting Mounting Lower frame is mounted to chassis by threaded rods and clamp plates. No welding to truck chassis is required. Lower Frame Torsion resistant, rigid 4-plate design. Rear Underride Protection Supplied on factory mounted cranes. Fabricated structure mounted under rear of carrier. Complies with Bureau of Motor Carrier Safety Standard 393.6. Boom Rest Heavy-duty, removable. Control System Single operator platform and seat mounted to turret. Four single-axis crane controls, bubble level and system pressure gauge arranged to ANSI B.5 standards. The operator station includes engine start/stop, air foot throttle, signal horn, boom angle indicator, swing limit indicator, load chart and range diagram. Hydraulics Hydraulic System A 3-section vane pump directmounted to power take-off on truck transmission provides 35 gpm (133 lpm) to the hoist, 1 gpm (6 lpm) to perform other crane functions, and gpm ( lpm) to the swing and outrigger circuit. -gallon (265-liter) baffled reservoir with strainer and 25-micron filter in the return lines. Ball-type shutoff valve and strainer are provided in suction line. All fittings are ORS type and SAE. Hydraulic Cylinders All load-holding cylinders are equipped with integral holding valves. Warning Systems Anti-Two-Block System Audible warning and shutoff functions prevent hook from contacting boom point. Load Moment Indicator (LMI) Senses boom hoist cylinder pressure, boom length and boom angle. Audio-visual warning indicates overload conditions and overload shutoff feature prevents continuing overload. Operator can access all relative crane configuration and load conditions via display at the operator station. Back-Up Alarm Electronic audible motion alarm activated when truck transmission is in reverse gear. General Electrical State-of-the-art, weather-resistant components throughout. Automotive style electrical system for easy installation. Designed to withstand high pressure washing and varying climates.
specifications Design/Welding Design conforms to ANSI B.5. Welding conforms to AWS D1.1. Tested to SAE 63 and SAE 765. Manuals Operator, service and parts manuals depict correct crane operation, maintenance procedures and parts listing. Warranty -month warranty covers parts and labor resulting from defects in material and workmanship. Warning 1. The operator must read and understand the owner s manual before operating this crane. 2. Positioning or operation of crane beyond areas shown on this chart is not intended or approved except where specified in owner s manual. 3. Loaded boom angles at specified boom lengths give only an approximation of the operating radius. The boom angle before loading should be greater to account for deflections. Do not exceed the operating radius for rated loads. 4. The operating radius shown in the jib rating chart is for fully extended boom only. When boom is not fully extended, use only loaded boom angle to determine load rating of jib. 5. For boom angles shown on jib load rating chart, use rating of next lower boom angle. 6. For boom lengths not shown, use rating of next shorter or longer boom length, whichever is less. For radii not shown, use rating of next longer radius. 7. Crane load ratings on outriggers are based on freely suspended loads with the machine leveled and standing on a firm uniform supporting surface. No attempt shall be made to move a load horizontally on the ground in any direction.. Practical working loads depend on supporting surface, wind, and other factors affecting stability such as hazardous surroundings, experience of personnel, and proper handling, all of which must be taken into account by the operator. 9. The maximum load which may be telescoped is limited by hydraulic pressure, boom angle, and boom lubrication. It is safe to attempt to telescope any load within the limits of the load rating chart.. Lifting off the main boom point while the swingaround jib is erected is not intended or approved. 11. All load ratings above the heavy line are based on machine structural competence and do not exceed 5% of tipping. Load ratings below are stability limited and do not exceed 5% of tipping.. Do not operate a Manitowoc truck-mounted crane or accessories within ' (3,05 m) of live power lines. 13. This capacity chart is for reference only and must not be used for specific serial number cranes. Information 1. Deductions must be made from rated loads for stowed jib, optional attachments, hooks, and loadblocks (see deduction chart). Weights of slings and all other load handling devices shall be considered a part of the load. 2. Load ratings above the heavy line are structurally limited capacities. Load ratings below the heavy line are stability limited capacities and do not exceed 5% of tipping. Definitions 1. Operating radius (r ) is the horizontal distance from the axis of rotation to the center of the vertical hoist line or tackle with load applied (see below). 2. Loaded boom angle ( ), as shown in the column headed by, is the included angle between the horizontal and longitudinal axes of the boom base after lifting rated load at rated radius (see below). r 3 NOTE: Due to continuing improvements, reserves the right to change product specifications without notice.
outline dimensions 4 ' 5.3" (,97 m) RETRACTED 1' 5.3" (,92 m) EXTENDED 2" (5 35 mm) 271" EOF (6 3 mm) 16" (6 mm) 11'.5" (3,57 m) 3' 11.5" (11,53 m) 13' 3.1" (4,04 m) " (1 016 mm) 11' 7" (3,53 m) 61.9" (1 572 mm) SINGLE 62.9" (1 59 mm) DUAL 256" WB (6 502 mm) SINGLE 237" WB (6 0 mm) DUAL 16" CA (4 724 mm) 16" CT (4 267 mm) 196" (4 97 mm) 47.5" (1 7 mm) 4' 11.5" (1,51 m) 17.2" (436 mm) 33' 7.5" OAL (, m) Chassis Data Weights Minimum Truck Requirements 221S 221S SINGLE DUAL 221S SINGLE & DUAL Wheease (WB) 256" (6 502 mm) 237" (6 0 mm) Crane- With Out Cab 1,553 ( 416 kg) Cab to Axle (CA) 16" (4 724 mm) - Cab Alone 575 (261 kg) Cab to Tandem (CT) - 16" (4 267 mm) 13' (4,0 m) Flat Bed 1,0 (544 kg) Cab to End of Frame (EOF) 271" (6 3 mm) 271" (6 3 mm) ' (, m) Fixed Length Jib 6 (9 kg) Frame Section Modulus 15.9 in 3 1,000 psi (75 422 kpa) 15.9 in 3 1,000 psi (75 422 kpa) *Minimum chassis weight is required to meet 5% stability requirements. Frame Section Modulus Front Axle Gross Weight Rating Rear Axle Gross Weight Rating Minimum Truck Axle Weight Front* Minimum Truck Axle Weight Back* Nominal Frame Width 1.0 in 3 50,000 psi (344 750 kpa),000 (5 443 kg) 21,000 (9 525 kg) 5,750 (2 kg) 4,050 (1 37 kg) 34 " (64 mm) 1.0 in 3 50,000 psi (344 750 kpa),000 (5 443 kg) 34,000 (15 422 kg) 6,00 (3 04 kg) 7,0 (3 357 kg) 34 " (64 mm) Chassis data is general not for engineering. Some dimensions depend on truck selection. OAH Overall Height CT Cab to Tandem CA Cab to Axle WB Wheel Base OAL Overall Length BBC Bumper to Back of Cab AF Afterframe EOF End of Frame
outline dimensions 5 A 9.5 6" (152 mm) 19' 9.75" (6,04 m) 7.75" (197 mm) Maximum Tip Height (A) Configuration Extended Boom Fixed or Retracted Jib 221S Boom 1' 0" (, m) 1' " (33,7 m) 139' " (42,6 m)
boom/jib range diagram 6 221S Single Axle Range Diagram - Fully Extended (only avialable in fully extended position) (45,7) 150 (42,7) 1 JIB 0 75 = LOADED BOOM ANGLE (39,6) 1 1 (39,6) 65 (36,6) 1 55 (33,5) 1 50 (,5) 0 D (, ) 1 45 HEIGHT ABOVE GROUND (27,4) (24,4) 90 0 A (16,2) 53 B 69 C (25,9) 5 35 25 (15,2) 50 15 5 16" ( 6 mm ) BOOM HINGE POINT ROTATION 50 0 90 (3,0) (15,2) (24,4) (27,4) DISTANCE FROM CENTERLINE OF ROTATION NOTE: Use this chart only when outriggers and stabilizers are fully extended. 0 (,5) 0 1 (33,5) GROUND 264.0 REF - 22' 0" (6,71 m)
boom/jib load charts 221S Single Axle Load Ratings Fully Extended Outrigger Spread Boom/Jib Operating Radius A B C D 53 69 5 1 (16,2) (25,9) (,) (kg) (kg) (kg) (kg) (kg) 221S Jib Load Ratings Fixed Jib (kg) Boom/Jib Operating Radius 7 5 (1,5) 0 44,000 (19 95) 5 (1,5) (2,4) 74 33,5 (15 213) (2,4) (3,1) 2,1 ( 764) (3,1) (3,7) 66 24,2 7,000 ( 991) (6 350) (3,7) (4,3) 61,4 76,000 0,000 (9 21) (6 350) (6 350) (4,3) 17 (5,2) 54 16,0 72,000 7,0 (7 439) (6 350) (5 42) 17 (5,2) 46 13,5 69 13,0 75 11,4 79,9 (6 133) (6 2) (5 15) (4 046) 25 (7,6) 9,9 63,3 71 9,4 75,000 79 6,000 (4 495) (4 61) (4 1) (3 6) (2 722) 25 (7,6) 56 7, 66 7,9 72 7,0 76 5,500 (3 5) (3 615) (3 7) (2 495) 0 3,000 (1 361) 35 (,7) 49 6,0 61 6,0 6 6,1 73 4,90 (2 ) (2 5) (2 71) (2 259) 7 2, (1 2) 35 (,7) 41 4,990 56 5,0 65 5,150 4,490 (2 263) (2 3) (2 336) (2 037) 76 2,6 (1 1) 45 (13,7) 31 4,000 51 4,1 61 4,2 67 4,000 (1 ) (1 73) (1 9) (1 ) 73 2,4 (1 09) 45 (13,7) 50 (15,2) 17 3,10 45 3,3 57 3,390 64 3,4 (1 442) (1 53) (1 53) (1 5) 71 2,2 (1 0) 50 (15,2) 55 (16,) 3 2,60 52 2,750 61 2,00 (1 216) (1 247) (1 2) 69 2,0 (916) 55 (16,) 2,1 47 2,2 57 2,0 (94) (1 016) (1 039) 67 1, (35) 65 19 1,750 42 1, 54 1, (794) () (4) 64 1,6 (757) 65 36 1,40 50 1,5 (671) (69) 62 1,5 (69) 75 (22,9) 0 (24,4) 5 (25,9) 90 (27,4) 95 (,0) Deduction* *for stowed fixed jib 1,10 45 1,2 (535) (55) 9 41 9 (417) (4) 36 750 (3) 5 (254) 22 390 (177) 3 190 150 1 0 (154) (6) (6) (54) (45) 59 1,3 () 56 1,00 (490) 53 (390) 50 6 (4) 47 500 (227) 75 (22,9) 0 (24,4) 5 (25,9) 90 (27,4) 95 (,0) Meets ANSI B.5 Requirements - Do not operate crane or accessories within ' (3.05m) of live power lines. NOTICE: This capacity chart is for reference only and must not be used for lifting purposes.
boom/jib range diagram 221S Dual Axle Range Diagram - Fully Extended (45,7) 150 (42,7) 1 JIB 0 75 = LOADED BOOM ANGLE (39,6) 1 65 1 (39,6) (36,6) 1 55 (33,5) 1 50 (,5) 0 D (,) 1 45 HEIGHT ABOVE GROUND (27,4) (24,4) 90 0 A (16,2) 53 B 69 C (25,9) 5 25 35 (15,2) 50 15 5 (A) 16" ( 6 mm ) BOOM HINGE POINT (B) ROTATION 50 0 90 (3,0) (15,2) (24,4) (27,4) GROUND DISTANCE FROM CENTERLINE OF ROTATION (C) (A) (B) (C) Pins must be disengaged for this outrigger configuration These marks indicate when beams are fully extended All outrigger beams must be extended to full extend mark 0 (,5) 0 1 (33,5) 237. REF - 19' 9." (6,04 m) NOTE: Use this chart only when all outriggers are fully extended.
boom/jib load charts 221S Dual Axle Load Ratings Fully Extended Outrigger Spread Boom/Jib Operating Radius 5 (1,5) A B C D 53 69 5 1 (16,2) (25,9) (,) (kg) (kg) (kg) (kg) 0 44,000 (19 95) (kg) 221S Jib Load Ratings Fixed Jib (kg) Boom/Jib Operating Radius 5 (1,5) 9 (2,4) 74 33,5 (15 213) (2,4) (3,1) 2,1 ( 764) (3,1) (3,7) 66 24,2 7,000 ( 991) (6 350) (3,7) (4,3) 61,4 76,000 0,000 (9 21) (6 350) (6 350) (4,3) 17 (5,2) 54 16,0 72,000 7,0 (7 439) (6 350) (5 42) 17 (5,2) 46 13,5 69 13,0 75 11,4 79,9 (6 133) (6 2) (5 15) (4 046) 25 (7,6),2 63,0 71 9,4 75,000 79 6,000 (4 631) (4 0) (4 1) (3 6) (2 722) 25 (7,6) 56,390 66,2 72 7,0 76 5,500 (3 06) (3 724) (3 7) (2 495) 0 3,000 (1 361) 35 (,7) 49 6,790 61 6,90 6 6,1 73 4,90 (3 00) (3 5) (2 71) (2 259) 7 2, (1 2) 35 (,7) 41 5,590 56 5,0 65 5,3 4,490 (2 536) (2 55) (2 413) (2 037) 76 2,6 (1 1) 45 (13,7) 31 4,6 51 4,7 61 4,6 67 4,000 (2 5) (2 159) (2 5) (1 ) 73 2,4 (1 09) 45 (13,7) 50 (15,2) 17 3,0 45 4,000 57 4,0 64 3,50 (1 7) (1 ) (1 46) (1 624) 71 2,2 (1 0) 50 (15,2) 55 (16,) 3 3,30 52 3,450 61 3,0 (1 533) (1 565) (1 451) 69 2,0 (916) 55 (16,) 2, 47 2,9 57 2,50 (1 7) (1 3) (1 3) 67 1, (35) 65 19 2,4 42 2,490 54 2,5 (1 093) (1 1) (1 3) 64 1,6 (757) 65 36 2,090 50 2,1 (94) (966) 62 1,5 (69) 75 (22,9) 1,7 45 1,790 (79) () 59 1,30 (626) 75 (22,9) 0 (24,4) 5 (25,9) 90 (27,4) 95 (,0) 0 (,5) 5 (32,0) 1 (33,5) Deduction * *for stowed fixed jib 1,4 41 1,500 (653) (60) 36 1,2 (562) 1,0 (463) 22 (372) 3 190 150 1 0 (154) (6) (6) (54) (45) 56 1,2 (55) 53 1,00 (490) 50 950 (431) 47 (376) 44 7 (327) 5 (259) 36 4 (195) 0 (24,4) 5 (25,9) 90 (27,4) 95 (,0) 0 (,5) 5 (32,0) 1 (33,5) Meets ANSI B.5 Requirements - Do not operate crane or accessories within ' (3.05m) of live power lines. NOTICE: This capacity chart is for reference only and must not be used for lifting purposes.
boom/jib range diagram 221S Dual Axle Range Diagram - Intermediate (45,7) 150 (42,7) 1 JIB 0 75 = LOADED BOOM ANGLE (39,6) 1 65 1 (39,6) (36,6) 1 (33,5) 1 (,5) 0 D (,) 1 55 HEIGHT ABOVE GROUND (27,4) (24,4) 90 0 69 B 5 C (25,9) 50 45 53 A (16,2) 35 (15,2) 50 25 15 5 (B) 16" ( 6 mm ) BOOM HINGE POINT ROTATION 50 0 90 (3,0) (15,2) (24,4) (27,4) (C) DISTANCE FROM CENTERLINE OF ROTATION (A) (B) Mark indicates beam is mid extended Pins must be engaged for this outrigger configuration 0 0 (,5) NOTE: Lifting personnel with crane in this outrigger configuration is strictly prohibited. Use only fully extended outrigger configuration when lifting personnel. 1 (33,5) (A) GROUND (C) All outrigger beams must be extended to mid extend mark Use this chart only when all outriggers are in the intermediate position. 163.0 REF - 13' 7" (4, m)
boom/jib load charts 221S Dual Axle Load Ratings Intermediate Outrigger Spread Boom/Jib Operating Radius A B C D 53 69 5 1 (16,2) (25,9) (,) (kg) (kg) (kg) (kg) (kg) 221S Jib Load Ratings Fixed Jib (kg) Boom/Jib Operating Radius 11 5 (1,5) 0 44,000 (19 95) 5 (1,5) (2,4) 74 33,5 (15 213) (2,4) (3,1) 2,1 ( 764) (3,1) (3,7) 66 24,2 7,000 ( 991) (6 350) (3,7) (4,3) 61,4 76,000 0,000 (9 21) (6 350) (6 350) (4,3) 17 (5,2) 54,0 72,000 7,0 (6 36) (6 350) (5 42) 17 (5,2) 46,190 69,690 75, 79,9 (4 622) (4 49) (4 90) (4 046) 25 (7,6) 6,5 63 7,050 71 7,1 75 7,2 79 6,000 (2 976) (3 19) (3 252) (3 24) (2 722) 25 (7,6) 56 4,9 66 5,090 72 5,1 76 5,2 (2 254) (3 9) (2 341) (2 363) 0 3,000 (1 361) 35 (,7) 49 3,6 61 3,750 6 3, 73 3, (1 647) (1 1) (1 72) (1 751) 7 2, (1 2) 35 (,7) 41 2,690 56 2, 65 2, 2,9 (1 2) (1 275) (1 2) (1 3) 76 2,6 (1 1) 45 (13,7) 31 1,990 51 2,1 61 2,10 67 2,2 (903) (957) (99) (1 007) 73 2,3 (1 04) 45 (13,7) 50 (15,2) 17 1,450 45 1,5 57 1,6 64 1,60 (65) (7) (744) (762) 71 1,7 (03) 50 (15,2) 55 (16,) 3 1,150 52 1,2 61 1,2 (522) (553) (572) 69 1,350 (6) 55 (16,) 00 47 57 9 (363) (395) (413) 67 1,000 (454) 65 64 7 (322) 65 62 4 (213) Deduction* *for stowed fixed jib 3 19 150 1 0 (154) (6) (6) (54) (45) Meets ANSI B.5 Requirements - Do not operate crane or accessories within ' (3.05m) of live power lines. NOTICE: This capacity chart is for reference only and must not be used for lifting purposes.
boom/jib range diagram 221S Dual Axle Range Diagram - Fully Retracted (45,7) 150 (42,7) 1 = LOADED BOOM ANGLE (39,6) 1 (36,6) 1 (33,5) 1 0 75 D 1 (,) (,5) 0 (27,4) 90 C 5 (25,9) 65 HEIGHT ABOVE GROUND (24,4) 0 69 B 55 53 A (16,2) 50 (15,2) 50 45 35 25 15 5 (A) 16" ( 6 mm ) BOOM HINGE POINT ROTATION GROUND.4 REF - 7' 4.4" (2, m) 0 50 0 90 (3,0) (15,2) (24,4) (27,4) (B) (A) (B) DISTANCE FROM CENTERLINE OF ROTATION Pins must be disengaged for this outrigger configuration All outrigger beams must be fully retracted 0 (,5) NOTE: Lifting personnel with crane in this outrigger configuration is strictly prohibited. Use only fully extended outrigger configuration when lifting personnel. Use this chart only when all outriggers are fully retracted. 1 (33,5)
boom/jib load charts 221S Dual Axle Load Ratings Fully Retracted Outrigger Spread A B C D 13 Boom/Jib Operating Radius 5 (1,5) (2,4) (3,1) (3,7) (4,3) 17 (5,2) 25 (7,6) 35 (,7) 53 69 5 1 (16,2) (25,9) (,) (kg) (kg) (kg) (kg) 0 44,000 (19 95) 74 19,6 ( 904),5 (5 674) 66, 7 9,2 (3 996) (4 5) 61 6,5 76 6,9 0 7,090 (2 966) (3 162) (3 216) 54 4,4 72 4, 7 4,9 (2 005) (2 191) (2 241) 46 3 0 69 3 4 75 3 50 79 3,6 (1 3) (1 574) (1 624) (1 651) (kg) 1,6 63 2,050 71 2,1 75 2,2 79 2,2 (744) (9) (90) (1 007) (1 025) 56 1,1 66 1,2 72 1,3 76 1,3 (531) (576) (3) (621) 61 6 6 7 73 7 (4) (331) (349) Deduction* *for stowed fixed jib 3 190 150 1 0 (154) (6) (6) (54) (45) Meets ANSI B.5 Requirements - Do not operate crane or accessories within ' (3.05m) of live power lines. NOTICE: This capacity chart is for reference only and must not be used for lifting purposes.
load chart data Deductions Auxillary Block Load Block Overhaul Ball Hose Reel Swing Around Jib* (Stowed) 50 (23 kg) See manufacturer s nameplate See manufacturer s nameplate 1 (73 kg) See load rating chart Area of Operation Standard 3 Full Capacity Work Area The front tires must be in contact with the ground, and the machine level, when operating in this area Allowable Line Pull 1 Part Line 2 Part Line 3 Part Line 4 Part Line 5 Part Line 6 Part Line 7,0,00 22,0,0 37,000 44,000 (3 375 kg) (6 713kg) ( 0 kg) (13 426 kg) (16 73 kg) ( 1 kg),500 17,000 25,500 34,000 42,500 44,000 (3 56 kg) (7 711 kg) (11 567 kg) (15 422 kg) (19 27 kg) ( 1 kg) 9/16" 6 x 25 IWRC (3.5:1 SF),750 Min Breaking Strength 9/16" Rotation Resistant (5.0:1 SF) 37,000 Min Breaking Strength Warning Anti-two-block system must be in good operating condition before operating crane. Refer to the owner s manual. Keep at least three wraps of load line on the drum at all times.
SM CraneCARE CraneCARE is complete service and support program. Incorporated into this program are service training, immediate parts availability, professional field service, and technical support and documentation. CraneCARE is available for every one of the thousands of cranes still operating all over the world. That s dedication and devotion that you won t get anywhere else. That s CraneCARE. Technical Support dealer network and factory personnel are available 24 hours a day, 7 days a week, 365 days a year to answer your technical questions and more. For a worldwide listing of dealer locations, please consult our website at: www.manitowocbt.com. 15 Service Training A certified service specialist works with you in your training facility or in the field to ensure that you know how to achieve maximum performance, dependability, and years from your cranes. A reputable Service technician comes to you to provide valuable training to all distributors on the crane s LMI system. Technical Documentation boast an extensive, easy-tounderstand library of documentation. A complete set of Operator s parts and service manuals are included with each crane. Additional copies are available through your Authorized Distributor. Parts Availability Genuine replacement parts may be obtained through your MBT distributor on a regular basis. Hydraulic Test Kit with Case Part No. 499792-9 Small national O-ring kit Pressure gauges Fluke multi-meter Hydraulic flow meters Multi-load grease gun 6-drawer tool box 17-piece wrench set Field Service Factory-trained service experts are always ready to help maintain your crane s peak performance. For a worldwide listing of dealer locations, please consult our website at: www.manitowocbt.com.
Backed by, part of Manitowoc Crane Group CraneCARE SM CraneCARE is complete service and support program. Incorporated into this program are service training, immediate parts availability, professional field service, and technical support and documentation. CraneCARE is available for every one of the thousands of cranes still operating all over the world. That s dedication and devotion that you won t get anywhere else. That s CraneCARE. 00 South Austin Avenue P.O. Box 19 Georgetown, TX, USA 7627-19 Telephone 5-942-00 Facsimile 5-63-3776 www.manitowocbt.com PRODUCT IMPROVEMENTS MAY CHANGE SPECIFICATIONS 01 MANITOWOC 0000-221S-PG-US-E-0000