Page 1 of 12 Last Modified: 9-21-2007 1.6 A Service Category: Vehicle Interior Section: Interior Panels/Trim Model Year: 2008 Model: Tundra Doc ID: RM000002VHU003X Title: INSTRUMENT PANEL: INSTRUMENT PANEL SAFETY PAD (for Floor Shift Type): REMOVAL (2008 Tundra) REMOVAL 1. TABLE OF BOLT, SCREW AND NUT HINT: All bolts, screws and nuts relevant to installing and removing the instrument panel are shown along with their alphabet code below. 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (a) Turn the ignition switch OFF and disconnect the cable from the negative (-) battery terminal. CAUTION: Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation. NOTICE: After the ignition switch is turned OFF, the navigation system requires approximately 90 seconds to record various types of memory and settings. As a result, after turning the ignition switch OFF, wait 90 seconds or more before disconnecting the cable from the negative (-) battery terminal. Some systems need to be initialized after the cable is reconnected.
Page 2 of 12 3. REMOVE LOWER NO. 2 STEERING WHEEL COVER 4. REMOVE LOWER NO. 3 STEERING WHEEL COVER 5. REMOVE STEERING PAD (w/o Steering Pad Switch) 6. REMOVE STEERING PAD (w/ Steering Pad Switch) 7. REMOVE STEERING WHEEL ASSEMBLY 8. REMOVE LOWER STEERING COLUMN COVER (for Manual Tilt and Manual Telescopic Steering Column) 9. REMOVE LOWER STEERING COLUMN COVER (for Power Tilt and Power Telescopic Steering Column) 10. REMOVE UPPER STEERING COLUMN COVER (for Manual Tilt and Manual Telescopic Steering Column) 11. REMOVE UPPER STEERING COLUMN COVER (for Power Tilt and Power Telescopic Steering Column) 12. REMOVE TILT AND TELESCOPIC MANUAL SWITCH (for Power Tilt and Power Telescopic Steering Column) 13. REMOVE TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY 14. REMOVE FRONT DOOR SCUFF PLATE LH (for Regular Cab) 15. REMOVE FRONT DOOR SCUFF PLATE LH (for Double Cab, CrewMax) 16. REMOVE COWL SIDE TRIM BOARD LH 17. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH (for Regular Cab) 18. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH (for Double Cab, CrewMax) 19. REMOVE FRONT PILLAR GARNISH LH 20. REMOVE INSTRUMENT SIDE PANEL LH (a) Using a moulding remover, detach the 7 claws and remove the side panel.
Page 3 of 12 21. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LH (a) Remove the hood lock control lever. (b) Remove the 2 bolts. (c) Detach the 4 clips and claw. (d) for Automatic Air Conditioning System: Detach the 2 claws and remove the sensor. (e) Remove the finish panel and then disconnect the connectors. 22. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (a) Twist the shift lever knob in the direction indicated by the arrow and remove it. 23. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY
Page 4 of 12 (a) Detach the 12 clips and remove the console panel. 24. REMOVE REAR UPPER CONSOLE PANEL SUB-ASSEMBLY (a) Remove the clip. (b) Detach the 6 clips and remove the console panel. (c) w/trailer Towing System: Disconnect the connector 25. REMOVE REAR CONSOLE END PANEL SUB-ASSEMBLY (a) Using a moulding remover, detach the 7 clips and remove the end panel. (b) except Regular Cab:
Page 5 of 12 Disconnect the connector. 26. REMOVE CONSOLE BOX CARPET 27. REMOVE REAR CONSOLE BOX ASSEMBLY (a) Remove the 2 screws. (b) Remove the 4 bolts and rear console box. 28. REMOVE FRONT CONSOLE BOX (a) Remove the 2 clips. (b) Remove the 6 screws and front console box. 29. REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY
Page 6 of 12 (a) Disconnect the connector and clamp. (b) Detach the 12 clips and remove the finish panel. 30. REMOVE COMBINATION METER ASSEMBLY (a) Remove the 4 screws. (b) Disconnect the connector and clamp, and remove the combination meter. 31. REMOVE CENTER LOWER INSTRUMENT PANEL FINISH PANEL (a) Detach the 4 clips. (b) Remove the finish panel and then disconnect the connectors. 32. REMOVE INTEGRATION CONTROL AND PANEL ASSEMBLY (for Manual Air Conditioning
Page 7 of 12 System) (a) Detach the 4 clips. (b) Remove the panel and then disconnect the connectors. 33. REMOVE INTEGRATION CONTROL AND PANEL ASSEMBLY (for Automatic Air Conditioning System) (a) Detach the 4 clips. (b) Remove the panel and then disconnect the connectors. 34. REMOVE RADIO RECEIVER ASSEMBLY WITH BRACKET 35. REMOVE NAVIGATION RECEIVER ASSEMBLY WITH BRACKET (w/ Navigation System) 36. REMOVE INSTRUMENT SIDE PANEL RH (a) Using a moulding remover, detach the 6 claws and remove the side panel. 37. REMOVE FRONT DOOR SCUFF PLATE RH (for Regular Cab) 38. REMOVE FRONT DOOR SCUFF PLATE RH (for Double Cab, CrewMax) 39. REMOVE COWL SIDE TRIM BOARD RH
Page 8 of 12 40. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH (for Regular Cab) 41. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH (for Double Cab, CrewMax) 42. REMOVE FRONT PILLAR GARNISH RH 43. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY RH (a) Remove the bolt. (b) Remove the 3 screws. (c) Detach the 3 claws and remove the finish panel. 44. REMOVE NO. 2 INSTRUMENT PANEL BOX DOOR SUB-ASSEMBLY (a) Using a screwdriver, detach the 4 claws to remove the 2 instrument panel hole covers. HINT: Tape the screwdriver tip before use. (b) Remove the 6 screws and box door. 45. REMOVE GLOVE BOX LIGHT ASSEMBLY
Page 9 of 12 (a) Detach the 2 claws. (b) Remove the box light and then disconnect the connector. 46. REMOVE INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY (a) Using a screwdriver, detach the 4 clips and claw, and remove the speaker panel. HINT: Tape the screwdriver tip before use. 47. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY LH 48. REMOVE NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY (a) Using a screwdriver, detach the 4 clips and claw, and remove the speaker panel. HINT: Tape the screwdriver tip before use. 49. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY RH (a) Remove the 2 bolts. (b) Remove the speaker and disconnect the connector. NOTICE: Do not touch the cone part of the speaker. 50. REMOVE NO. 3 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY
Page 10 of 12 (a) Using a screwdriver, detach the 6 clips and 2 claws, and remove the speaker panel. HINT: Tape the screwdriver tip before use. 51. REMOVE FRONT NO. 4 SPEAKER ASSEMBLY (for 10 Speaker Models) 52. REMOVE NO. 1 INSTRUMENT PANEL SAFETY PAD INSERT (a) Remove the 4 bolts. (b) Detach the 2 claws. (c) Remove the safety pad and then disconnect the connector. 53. REMOVE INSTRUMENT PANEL SUB-ASSEMBLY (a) Detach the connectors from the clamps and disconnect the connectors. (b) Remove the bolt and wire harness.
Page 11 of 12 (c) Remove the 2 passenger airbag bolts. (d) Remove the 3 bolts and 2 nuts. (e) Detach the 5 claws and remove the instrument panel.
Page 12 of 12 54. REMOVE NO. 3 INSTRUMENT PANEL STAY (a) Detach the 5 claws and remove the 5 stays.