idatastart HC Document number Revision Date

Similar documents
idatastart HC Document number Revision Date

idatastart HC Document number Revision Date

PRODUCT GUIDE FT-DC2-S DOCUMENT NUMBER REVISION DATE

idatastart HC Document number Revision Date

PRODUCT GUIDE FT-DC2-S DOCUMENT NUMBER REVISION DATE

PRODUCT GUIDE FT-DC2-S DOCUMENT NUMBER REVISION DATE

PRODUCT GUIDE HCF900A DOCUMENT NUMBER REVISION DATE

PRODUCT GUIDE HC1151A DOCUMENT NUMBER REVISION DATE

INSTALL GUIDE OEM-AL(RS)-NI9-[FLCAN]-EN

PRODUCT GUIDE FT-DC2-S DOCUMENT NUMBER REVISION DATE

PRODUCT GUIDE ORBIT1151A DOCUMENT NUMBER REVISION DATE

Alarms & Remote Start

INSTALL GUIDE OEM-AL(RS)-NI8-[FLCAN]-EN

Alarms & Remote Start

Alarms & Remote Start

PRODUCT GUIDE OL-RS-VW1 DOCUMENT NUMBER REVISION DATE

INSTALL GUIDE OEM-AL(RS)-FM8-[ADS-ALCA]-EN

install guide ADS-AL(RS)-FM6-[ADS-ALCA]-EN

INSTALL GUIDE OEM-AL(RS)-TL1-[ADS-ALCA]-EN

INSTALL GUIDE OEM-AL(RS)-TL2-[FLCAN]-EN

INSTALL GUIDE OL-AL(RS)-CH5-[OL-MDB-ALL]-EN

PRODUCT GUIDE VWX000A DOCUMENT NUMBER REVISION DATE

PRODUCT GUIDE RS1B-DC2 DOCUMENT NUMBER REVISION DATE

INSTALL GUIDE OEM-AL(RS)-FM6-[OL-MDB-ALL]-EN

INSTALL GUIDE OEM-AL(RS)-CH5-[FLCAN]-EN

INSTALL GUIDE ORB-AL(RS)-CH5-[ADS-ALCA]-EN

INSTALL GUIDE OEM-AL(RS)-FM6-[FLCAN]-EN

INSTALL GUIDE OEM-AL(RS)-TL7-[FLCAN]-EN

INSTALL GUIDE OEM-AL(RS)-FM8-[FLCAN]-EN

INSTALL GUIDE COM-HA(RS)-HA6P-[FT-HA6-DC]-EN

INSTALL GUIDE IDL-HA(RS)-HA7-[ADS-HA7]-EN

INSTALL GUIDE OEM-AL(RS)-CH8-[FLCAN]-EN

INSTALL GUIDE OEM-AL(RS)-CH5-[ADS-ALCA]-EN

INSTALL GUIDE FLC-CH(RS)-CH8-[FLRSCH7]-EN

INSTALL GUIDE DIR-CH(RS)-CH8-[FLRSCH10]-EN

INSTALL GUIDE COM-CH(RS)-CH4-[FT-CH4-DC]-EN

INSTALL GUIDE OL-HA(RS)-HA6P-[OL-RS-HA6]-EN

INSTALL GUIDE FLCI-CH(RS)-CH7-[FLRSCH7]-EN

INSTALL GUIDE OEM-AL(RS)-CH5-[ADS-ALCA]-EN

INSTALL GUIDE OL-FO(RS)-FO1B-[OL-RS-FO1]-EN

INSTALL GUIDE OEM-GM(RS)-GM2-[OL-RS-GM2]-EN

INSTALL GUIDE FLC-HA(RS)-HA6P-[FLRSHA6]-EN

INSTALL GUIDE ORB-AL(RS)-CH4-[ADS-ALCA]-EN

INSTALL GUIDE OEM-GM(RS)-GM2-[ADS-GM2]-EN

INSTALL GUIDE FLC-NI(RS)-NI6-[FLRSNI5]-EN

install guide OEM-AL(RS)-FM6-[ADS-ALCA]-EN

INSTALL GUIDE OL-CH(RS)-CH4-[OL-RS-CH4]-EN

INSTALL GUIDE OEM-AL(RS)-CH8-[OL-MDB-ALL]-EN

INSTALL GUIDE COM-CH(RS)-CH5-[FT-CH5-DC]-EN

INSTALL GUIDE OEM-CH(RS)-CH8-[FLRSCH10]-EN

INSTALL GUIDE IDL-IDS(RS)-BZ2B-[ADS-BZ2]-EN

INSTALL GUIDE AKX-IDS(RS)-BZ1B-[ADS-BZ1]-EN

PRODUCT GUIDE CMVWXA0

INSTALL GUIDE ORB-AL(RS)-CH4-[ADS-ALCA]-EN

INSTALL GUIDE COM-CH(RS)-CH5-[FT-CH5-DC]-EN

install guide FLC-CH(RS)-CH5-[FLRSCH5]-EN

install guide COM-IDS(RS)-BM1-[ADS-BM1]-EN

INSTALL GUIDE FLC-GM(RS)-GM10-[FLRSGM10]-EN

install guide OEM-IDS(RS)-BM1-[ADS-BM1]-EN

INSTALL GUIDE AKX-IDS(RS)-BM1-[ADS-BM1]-EN

install guide FLC-CH(RS)-CH4-[FLRSCH4]-EN

INSTALL GUIDE FLCI-IDS(RS)-BZ4-[FLRSBZ4]-EN

INSTALL GUIDE OL-NI(RS)-NI5-[OL-RS-NI5]-EN

INSTALL GUIDE IDL-IDS(RS)-BM1-[ADS-BM1]-EN

INSTALL GUIDE OEM-GM(RS)-GM10-[OL-RS-GM10]-EN

INSTALL GUIDE FLC-GM(RS)-GM10-[FLRSGM10]-EN

INSTALL GUIDE DIR-IDS(RS)-BM1-[FLRSBM1]-EN

INSTALL GUIDE FLCI-CH(RS)-CH5-[FLRSCH5]-EN

INSTALL GUIDE OL-GM(RS)-GM10-[OL-RS-GM10]-EN

INSTALL GUIDE FLC-CH(RS)-CH5-[FLRSCH5]-EN

Alarms & Remote Start

install guide OEM-IDS(RS)-BM1-[ADS-BM1]-EN

INSTALL GUIDE OEM-CH(RS)-CH4-[ADS-CH4]-EN

FT-DC3 MASTER GUIDE DIGITAL REMOTE STARTER + ALARM REV B

Automotive Data Solutions Inc. AVAILABLE FOR : ADS-AL CA. Rev. Date: January 18, 2018 Doc. No.: ##47342##

Automotive Data Solutions Inc. Rev. Date: November 26, 2013 Doc. No.: ##13245##

Automotive Data Solutions Inc. AVAILABLE FOR : ADS-AL CA. Rev. Date: August 29, 2018 Doc. No.: ##52817##

U.S. Patent No. 8,856,780 INSTALL TYPE SELECTION INSTALL TYPE

Automotive Data Solutions Inc. AVAILABLE FOR : ADS-AL CA. Rev. Date: January 18, 2018 Doc. No.: ##47334##

Automotive Data Solutions Inc. AVAILABLE FOR : ADS-AL CA. Rev. Date: May 15, 2017 Doc. No.: ##39060##

VW7 INSTALL GUIDE ADS-AL(DL)-VW7-EN. Alarms & Remote Start. Automotive Data Solutions Inc.

Automotive Data Solutions Inc. AVAILABLE FOR : FLCAN. Rev. Date: June 28, 2018 Doc. No.: ##51678##

Automotive Data Solutions Inc. AVAILABLE FOR : ADS-AL CA. Rev. Date: April 17, 2018 Doc. No.: ##49944##

Automotive Data Solutions Inc. Rev. Date: October 28, 2015 Doc. No.: ##23962##

HA2 INSTALL GUIDE ADS-AL(DL)-HA2-EN. Alarms & Remote Start. Automotive Data Solutions Inc.

Automotive Data Solutions Inc. AVAILABLE FOR : ADS-AL CA. Rev. Date: January 03, 2018 Doc. No.: ##46808##

Alarms & Remote Start

INSTALLATION GUIDE. FCC ID NOTICE

Automotive Data Solutions Inc. Rev. Date: August 07, 2014 Doc. No.: ##15683##

Automotive Data Solutions Inc. AVAILABLE FOR : FLCAN. Rev. Date: December 27, 2017 Doc. No.: ##46765##

TL2 INSTALL GUIDE OL-AL(MDB)-TL2-EN. Alarms & Remote Start. Automotive Data Solutions Inc.

VW3 INSTALL GUIDE OL-AL(MDB)-VW3-EN. Alarms & Remote Start. Automotive Data Solutions Inc.

Automotive Data Solutions Inc. AVAILABLE FOR : ADS-AL CA. Rev. Date: September 14, 2017 Doc. No.: ##44374##

HA2 INSTALL GUIDE OL-AL(MDB)-HA2-EN. Alarms & Remote Start. Automotive Data Solutions Inc.

Automotive Data Solutions Inc. AVAILABLE FOR : ADS-BLADE AL. Rev. Date: September 14, 2018 Doc. No.: ##53307##

GM2. Alarms & Remote Start. Automotive Data Solutions Inc.

2 WAY REMOTE STARTER & ALARM SYSTEM INSTALLATION GUIDE FCC ID NOTICE

Alarms & Remote Start Automotive Data Solutions Inc.

Automotive Data Solutions Inc. Rev. Date: November 16, 2012 Doc. No.: ##10129##

Automotive Data Solutions Inc. AVAILABLE FOR : ADS-AL CA. Rev. Date: December 3, 2018 Doc. No.: ##56063##

Transcription:

PRODUCT guide Document number Revision Date 20151001 NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. Please review the Installation Guide carefully before beginning any work.

BOX CONTENTS - 1 OF 1 Page 2 of 17 BOX CONTENTS HC MODULE Included with the HCF, HCX, HC1, HC2 Part Numbers: HCF900A, HC1151AC, HC2351AC, HC2352AC, HCX000A M1 8 PIN BLACK 8 PIN BLACK CONNECTOR 12 PIN BLACK CONNECTOR [1x] 1-WAY REMOTE [1x] 2-WAY REMOTE Included with the HC2 Part Number: HC2351AC 10 PIN WHITE CONNECTOR M2 : 12 PIN BLACK M3 : 10 PIN WHITE TELEMATIC : 4 PIN BLUE 4 PIN RED 4 PIN RED M5 : 6 PIN BLUE M4 : 20 PIN BLACK 3 PIN BLACK PROGRAMMING BUTTON 20 PIN BLACK CONNECTOR 6 PIN BLUE CONNECTOR [2x] 2-WAY REMOTES Included with the HC2 Part Number: HC2352AC LED 1 LED 2 RF/WEBLINK : 4 PIN BLACK USB AFTERMARKET HOOD SWITCH AND CABLE [2x] STICKERS DECODER Included with the HCF Part Number: HCF900A ANTENNA Included with the HC1, HC2 Part Numbers: HC1151AC, HC2351AC, HC2352AC [2x] 1-WAY REMOTES Included with the HC1 Part Number: HC1151AC ANTENNA LED 2 PIN BLACK RF PORT : 4 PIN BLACK ANTENNA PORT : 4 PIN WHITE 6 PIN WHITE RF PORT : 4 PIN BLACK ANTENNA LED ANTENNA BUTTON BLUE CABLE WITH 4 PIN BLACK CONNECTORS BLACK CABLE WITH 4 PIN BLUE CONNECTORS MODULE RF PORT DECODER RF PORT MODULE RF PORT ANTENNA RF PORT

MODULE PINOUT - 1 OF 1 Page 3 of 17 HC MODULE 2 4 6 8 1 3 5 7 M1 01 ORANGE - ACCESSORY (+) 02 RED - POWER (30A) 03 PURPLE - ER (+) 04 PINK/WHITE - PROG. 1 - IGNITION 2 (+) (DEFAULT) 05 PINK - IGNITION (+) 06 WHITE - PROG. 2 (10A) - PARKING LIGHTS (+) (DEFAULT) 07 RED - POWER (30A) 08 BLACK - GROUND M1 2 1 4 3 6 5 8 7 10 9 12 11 M2 01 GREEN BLACK DOT - LOCK (-) OUTPUT 02 BLUE BLACK DOT - UNLOCK (-) OUTPUT 03 RED/WHITE BLACK DOT - TRUNK RELEASE (-) OUTPUT 04 GREEN/WHITE BLACK DOT - ARM (-) OUTPUT 05 GREEN/BLACK BLACK DOT - DISARM (-) OUTPUT 06 BLUE/WHITE BLACK DOT - GWR (-) OUTPUT 07 EMPTY 08 WHITE/PURPLE BLACK DOT - POC 1 - UNLOCK DRIVER (-) OUTPUT 09 PURPLE/BLACK BLACK DOT - POC 2 - RAP SHUTDOWN (-) OUTPUT 10 WHITE/BLACK BLACK DOT - POC 3 - HORN (-) OUTPUT 11 BROWN/BLACK BLACK DOT - POC 4 - ER KILL (-) OUTPUT 12 WHITE BLACK DOT - PARKING LIGHTS (-) OUTPUT M2 M3 M5 M4 2 4 6 8 10 1 3 5 7 9 M3 01 BROWN SILVER DOT - BRAKE (+) INPUT 02 BLACK/WHITE SILVER DOT - E-BRAKE (-) INPUT 03 PURPLE SILVER DOT - DOOR (+) INPUT 04 GREEN SILVER DOT - DOOR (-) INPUT 05 PURPLE/WHITE SILVER DOT - TACH (-) INPUT 06 WHITE/BLUE SILVER DOT - X-TRIGGER (-) INPUT 07 GRAY SILVER DOT - HOOD (-) INPUT 08 BLUE SILVER DOT - TRUNK (-) INPUT 09 GRAY/BLACK SILVER DOT - GLOW PLUG (+) INPUT 10 NEGATIVE (-) INPUT 2 1 4 3 6 5 8 7 10 9 12 11 14 13 16 15 18 17 20 19 M4 01 EMPTY 02 EMPTY 03 BROWN/RED 04 BROWN/YELLOW 05 BLUE/RED 06 BLUE/YELLOW 07 EMPTY 08 ORANGE 09 YELLOW 10 EMPTY 11 GRAY/RED 12 GRAY/YELLOW 13 GREEN/RED 14 ORANGE/WHITE 15 BROWN 16 ORANGE/BLACK 17 PINK 18 PURPLE 19 RED 20 BLACK 1 3 5 2 4 6 M5 01 GRAY/BLACK BLUE DOT 02 WHITE/BLACK BLUE DOT 03 GRAY/RED BLUE DOT 04 WHITE/RED BLUE DOT 05 GRAY BLUE DOT 06 WHITE BLUE DOT

COMPATIBLE ACCESSORIES - 1 OF 2 Page 4 of 17 WEBLINK CABLE (required accessory sold separately) WEBLINK CABLE MODULE WEBLINK PORT COMPUTER USB PORT 4 PIN BLACK CABLE WEBLINK MOBILE (required accessory sold separately) OBDII CONNECTOR MODULE WEBLINK PORT 4 PIN BLACK CABLE MOBILE DEVICE PORT 1 2 3 4 5 6 7 8 OBDII CONNECTOR 9 10 11 12 13 14 15 16 TELEMATIC KIT (accessory sold separately) DRONE MODULE TELEMATIC PORT (NC)

COMPATIBLE ACCESSORIES - 2 OF 2 Page 5 of 17 DECODER (included with the HCF) RF KIT (sold separately) MODULE RF PORT DECODER (NC) RED (NC) BLACK BLACK BLUE RF KIT FLASH THE DECODER BEFORE THE INSTALLATION BLUE CABLE DECODER BLACK CABLE ANTENNA RF KIT (included with the HC1 & HC2) MODULE RF PORT 4 PIN BLACK CABLE ANTENNA

VALET MODE PROGRAMMING PROCEDURE - 1 OF 1 Page 6 of 17 >> NOTE: In Valet Mode, the Remote starter is not functional. Keyless entry, Lock and Unlock will remain functional. See RF kit user manual for alternate valet mode programming. 06 Valet Mode Programming Procedure completed. 01 Time restriction. Complete next step within 7 seconds. >> To exit valet mode: repeat steps 1 to 5. 02 ACC ON Cycle ignition ON twice [2x /ON] rapidly. ENGINE STOP 03 Press and release the BRAKE pedal three times [3x]. 04 Parking Light will flash once [1x] then will flash twice [2x]. 05 ACC ON Set ignition to position. ENGINE STOP

AFTERMARKET REMOTE PROGRAMMING PROCEDURE - 1 OF 1 Page 7 of 17 >> WARNING: Program aftermarket remotes before usage. A maximum of four [4x] aftermarket remotes per system. 05 Release the antenna button. The antenna s leds will turn. 01 ACC ON Set ignition to ON position. 06 Wait, Parking Light will flash twice [2x]. ENGINE STOP 02 Press and release the antenna button, then press and hold the antenna button. The antenna s leds will turn solid BLUE. 07 ACC ON Set ignition to position. ENGINE STOP 03 Parking Light will flash once [1x]. 08 Aftermarket Remote Programming Procedure completed. 04 Press once [1x] on LOCK button of aftermarket remote. The antenna s leds will flash BLUE once [1x]. >> To program additional remotes: repeat step 5 using each additional remote.

online MoDULe SeTTINgS - 1 OF 7 Page 8 of 17 01 - REMOTE ER OPTION options SeTTINgS 01 gas 02 DIESEL (GLOW PLUG) 03 3 SEC 01 ENGINE/WAIT TO 04 5 SEC 05 10 SEC 06 15 SEC 07 25 SEC 08 45 SEC 01 TaCH 02 TACHLESS 03 ASSUME (2) 02 ENGINE SENSING 04 ASSUME (2.5) 05 ASSUME (3) 06 ASSUME (4) 07 ASSUME (5) 01 3 MIN 02 5 MIN 03 10 MIN 03 RUN TIME 04 15 MIN 05 25 MIN 06 30 MIN 07 35 MIN 01 IgNITIoN 02 ACCESSORIES 04 PROGRAMMABLE 4TH RELAY 03 ER 04 TRUNK 05 PARKING 01 IGNITION 02 ACCESSORIES 05 PROGRAMMABLE 5TH RELAY 03 ER 04 TRUNK 05 PaRKINg 01 ReMoTe 06 MT ACTIVATION SEQUENCE 02 2X EBRAKE 03 1X EBRAKE 01 OPEN/CLOSE DOOR 07 MT SHUTDOWN SEQUENCE 02 10 SEC AFTER OPEN/CLOSE DOOR 03 ReMoTe 08 WEATHER MODE Default settings are listed in bold. 01 - REMOTE ER OPTION options 08 WEATHER MODE 09 10 TEMP SENSOR FOR COLD WEATHER TEMP SENSOR FOR HOT WEATHER 11 IDLE MODE 12 TURBO TIMER 13 TAKE OVER BEHAVIOUR 14 SECURE TAKE OVER DELAY 15 16 FACTORY KEYLESS RS SEQUENCE EXTERNAL RS INPUT TRIGGER (X-TRIG 17 VALET MODE 02 EVERY 2 HOUR 03 EVERY 3 HOUR 04 EVERY 4 HOUR SeTTINgS 05 WITH TEMP SENSOR 02-20C/-4F 03-15C/5F 04-10C/14F 05-5C/23F 02 25C/77F 03 30C/86F 04 35C/85F 05 40C/104F 01 DISABLE 02 enable 02 30 SEC 03 1 MIN 04 2 MIN 05 4 MIN 01 enable 02 SHUTDOWN WITH DOOR 03 SHUTDOWN WITH UNLOCK 01 45 SeC 02 90 SEC 03 3 MIN 04 4 MIN 01 DISABLE 02 HOLD LOCK 3 SEC 03 LOCK, UNLOCK, LOCK 04 LoCK, LoCK, LoCK 02 SINGLE PULSE (-) 03 DOUBLE PULSE (-)(-) 04 TRIPLE PULSE (-)(-)(-) 05 ANALOG FACTORY KEYLESS X-TRIGGER =LOCK INPUT DOOR(+) =UNLOCK INPUT 01 REMOTE OR 5 X IGNITION ON OR 2 X IGN. ON + 3 BRAKE 02 REMOTE OR ANTENNA BUTTON ONLY

online MoDULe SeTTINgS - 2 OF 7 Page 9 of 17 01 - REMOTE ER OPTION 02 - DOORLOCK OPTION 17 VALET MODE options 18 HEATED ACC CONTROL 19 COOLED SEATS CONTROL 20 21 RS PARKING LIGHTS CONFIRMATION CRANK TIME ADJUSTMENT (TACH) 22 REMOTE ER 01 02 DOORLOCK ANALOG OUTPUT DURATION TRUNK ANALOG OUTPUT DURATION Default settings are listed in bold. SeTTINgS 03 REMOTE OR ANTENNA OR 5 X IGN ON OR 2 X IGN ON + 3 BRAKE 04 REMOTE OR 5 X IGN ON 05 antenna or ReMoTe or 2 X IgN on + 3 BRaKe 06 5 X IGN ON OR 2 X IGN ON + 3 BRAKE 07 ANTENNA BUTTON ONLY 08 ANTENNA OR 5 X IGNITION ON OR 2 X IGN ON + 3 BRAKE 01 AUX TRIGGER 02 ALWAYS ON 03-10C/14F 04-5C/24F 05 0C/32F 06 4C/40F 07 8C/46F 08 12C/54f 01 AUX TRIGGER 02 ALWAYS ON 03 20C/68f 04 24C/76F 05 28C/82F 06 32C/90F 07 36C/96F 01 DISABLE 02 CoNSTaNT 03 FLASHING 02 +0.2 SECOND TO CRANK 03 +0.6 SECOND TO CRANK 04-0.2 SECOND TO CRANK 01 DISABLE 02 enable 01 0.4 SEC 02 0.8 SeC 03 2 SEC 04 4 SEC 01 0.4 SEC 02 0.8 SeC 03 2 SEC 04 4 SEC 02 - DOORLOCK OPTION options 03 PRIORITY UNLOCK 04 DOUBLE PULSE LOCK 05 DOUBLE PULSE UNLOCK 06 AUTO RE-LOCK 07 UNLOCK BEFORE 08 RE-LOCK AFTER 09 RE-LOCK AFTER RS SHUTDOWN 10 LOCK AFTER MT SHUTDOWN SEQUENCE 11 LOCK AFTER TURBO MODE 12 13 IGNITION CONTROLLED DOORLOCK IGNITION CONTROLLED DOORLOCK SETTING 14 TRUNK SEQUENCE 15 ANALOG REARM TRIGGER 16 ANALOG DISARM SEQUENCE 17 DL PARKING LIGHTS CONFIRMATION SeTTINgS 02 ENABLE 02 ENABLE 02 ENABLE 02 ENABLE 02 ENABLE 02 ENABLE 03 SMART RE-LOCK 02 ENABLE 03 SMART RE-LOCK 02 ENABLE 03 SMART RE-LOCK 02 ENABLE 02 ENABLE 03 ENABLE 2000 RPM 01 LoCK + UNLoCK 02 LOCK ONLY 03 UNLOCK ONLY 01 DISaRM, UNLoCK and TRUNK 02 DISARM AND TRUNK 03 TRUNK ONLY 01 after STaRT, SHUTDoWN and first LoCK 02 AFTER SHUT DOWN AND FIRST LOCK 03 AFTER ONLY 04 AFTER SHUTDOWN ONLY 01 DISaRM only 02 DISARM WITH IGN CYCLE 01 DISABLE 02 enable 03 ENABLE WITH IGNITION ONLY 04 ENABLE WITHOUT IGNITION

online MoDULe SeTTINgS - 3 OF 7 Page 10 of 17 03 - ALARM/SECURITY OPTION 01 ALARM options 02 ALARM DURATION 03 ALARM TRIGGERED BEHAVIOR 04 PASSIVE ALARM/LOCKS 05 06 07 PASSIVE ALARM/AUTO-RELOCK NOTI PASSIVE ALARM/AUTO-RELOCK TIMING PASSIVE OPEN ZONE BYPASS (FORCE 08 OPEN ZONE NOTIFICATION 09 10 CONFIRMATION CHIRP (HORN OUTPUT) CONFIRMATION CHIRP (SIREN OUTPUT) Default settings are listed in bold. SeTTINgS 02 ENABLE 01 30 SEC 02 60 SeC 03 120 SEC 01 No DeLaY 02 DELAY WITH PARKING LIGHTS 03 DELAY WITH PARKING LIGHTS AND CHIRPS 01 ACTIVE ONLY 02 ALARM & LOCKS 03 alarm only 04 LOCKS ONLY 02 ALARM & LOCKS 03 ALARM ONLY 04 LOCKS ONLY 01 30 SeC 02 60 SEC 03 5 MIN 04 10 MIN 02 ENABLE 01 DISABLE 02 enable 03 15 SEC DELAY 04 20 SEC DELAY 05 25 SEC DELAY 06 30 SEC DELAY 07 35 SEC DELAY 01 DISABLE 02 LOCK ONLY 03 DoUBLe LoCK only 04 LOCK AND UNLOCK 05 UNLOCK ONLY 06 LOCK, UNLOCK, 07 DOUBLE LOCK, 01 DISABLE 02 LOCK ONLY 03 DOUBLE LOCK ONLY 03 - ALARM/SECURITY OPTION options SeTTINgS 04 LoCK and UNLoCK 10 CONFIRMATION CHIRP (SIREN 05 UNLOCK ONLY OUTPUT) 06 LOCK, UNLOCK, 07 DOUBLE LOCK, 11 RESERSED FOR FUTURE USE 01 N/A 01 20 MS 02 30 MS 03 40 MS 12 CHIRP PULSE DURATION (HORN AND 04 45 MS 05 50 MS 06 60 MS 07 100 MS 01 DISABLE 13 SHOCK SENSOR INPUT 02 enable BEHAVIOUR 03 WARN AWAY ONLY 04 SHOCK ONLY 02 WARN AWAY ONLY (-) 14 ANALOG SENSOR (-) INPUT 03 SHOCK(-) BEHAVIOUR 04 NORMALY CLOSED ALARM(+) 05 ZONE 2 PASSIVE 15(-) 06 ZONE 2 PASSIVE 30(-) 15 ALARM CONTROL FROM OEM 01 DISABLE KEYLESS 02 enable 01 DISABLE 16 LED FLASHING 02 enable (IgNITIoN off only) 03 FOLLOW ALARM STATUS 17 ALARM/PANIC WITH PARKING 01 DISABLE LIGHTS 02 enable 01 5 SeC 18 CAR FINDER DURATION 02 10 SEC 03 15 SEC 04 60 SEC 01 anti-grind + active SK 19 ER KILL/ANTI-GRIND 02 ANTI-GRIND ONLY 03 ANTI-GRIND+ PASSIVE SK 30 SECONDS 04 ANTI-GRIND+ PASSIVE SK 60 SECONDS

online MoDULe SeTTINgS - 4 OF 7 Page 11 of 17 04 - AUX OPTION options SeTTINgS 01 LEFT SLIDE DOOR 02 RIGHT SLIDE DOOR 03 PTo 1 04 PTO 2 05 PTO 3 06 PTO 4 01 TRANSMITTER AUX 1 07 CAR FINDER 08 GAS CAP 09 REAR GLASS 10 HEATED SEATS 11 COOLED SEATS 12 PANIC 13 DEFROST 01 LEFT SLIDE DOOR 02 RIGHT SLIDE DOOR 03 PTO 1 04 PTo 2 05 PTO 3 06 PTO 4 02 TRANSMITTER AUX 2 07 CAR FINDER 08 GAS CAP 09 REAR GLASS 10 HEATED SEATS 11 COOLED SEATS 12 PANIC 13 DEFROST 01 LefT SLIDe DooR 02 RIGHT SLIDE DOOR 03 PTO 1 04 PTO 2 05 PTO 3 06 PTO 4 03 TRANSMITTER AUX 3 07 CAR FINDER 08 GAS CAP 09 REAR GLASS 10 HEATED SEATS 11 COOLED SEATS 12 PANIC 13 DEFROST 04 TRANSMITTER AUX 4 01 LEFT SLIDE DOOR Default settings are listed in bold. 04 - AUX OPTION 05 - AUX OPTION options 04 TRANSMITTER AUX 4 05 TRANSMITTER AUX 5 01 POC 1 SeTTINgS 02 RIgHT SLIDe DooR 03 PTO 1 04 PTO 2 05 PTO 3 06 PTO 4 07 CAR FINDER 08 GAS CAP 09 REAR GLASS 10 HEATED SEATS 11 COOLED SEATS 12 PANIC 13 DEFROST 01 LEFT SLIDE DOOR 02 RIGHT SLIDE DOOR 03 PTO 1 04 PTO 2 05 PTO 3 06 PTO 4 07 CaR finder 08 GAS CAP 09 REAR GLASS 10 HEATED SEATS 11 COOLED SEATS 12 PANIC 13 DEFROST 01 UNLoCK others 02 DEFROST 03 HORN 04 IGN 05 ACC 06 07 PARKING LIGHTS 08 PULSE TIMER OUTPUT 1 09 PTO1 10 PTO2 11 PTO3 12 PTO4 13 ARM 14 DISARM 15 LOCK

online MoDULe SeTTINgS - 5 OF 7 Page 12 of 17 05 - POC OPTION options 01 POC 1 02 POC 2 03 POC 3 Default settings are listed in bold. SeTTINgS 16 UNLOCK 17 TRUNK 18 GWR 19 LSD 20 RSD 21 RAP SHUTDOWN 22 CAR FINDER 01 UNLOCK OTHERS 02 DefRoST 03 HORN 04 IGN 05 ACC 06 07 PARKING LIGHTS 08 N/A 09 PTO1 10 PTO2 11 PTO3 12 PTO4 13 N/A 14 ARM 15 DISARM 16 LOCK 17 UNLOCK 18 TRUNK 19 GWR 20 LSD 21 RSD 22 RAP SHUTDOWN 01 UNLOCK OTHERS 02 DEFROST 03 HoRN 04 IGN 05 ACC 06 07 PARKING LIGHTS 08 PULSE TIMER OUTPUT 3 09 PTO1 10 PTO2 05 - POC OPTION 03 POC 3 04 options POC 4 (LOW CURRENT WHEN ACTIVE) SeTTINgS 11 PTO3 12 PTO4 13 ARM 14 DISARM 15 LOCK 16 UNLOCK 17 TRUNK 18 GWR 19 LSD 20 RSD 21 RAP SHUTDOWN 22 CAR FINDER 01 STaRTeR KILL 02 DEFROST 03 HORN 04 IGN 05 ACC 06 07 PARKING LIGHTS 08 PULSE TIMER OUTPUT 4 09 PTO1 10 PTO2 11 PTO3 12 PTO4 13 ARM 14 DISARM 15 LOCK 16 UNLOCK 17 TRUNK 18 GWR 19 LSD 20 RSD 21 RAP SHUTDOWN 22 CAR FINDER

online MoDULe SeTTINgS - 6 OF 7 Page 13 of 17 06 - PULSE TIMER OUTPUT OPTION options 01 PTO 1 DURATION 02 PTO 2 DURATION 03 PTO 3 DURATION 04 PTO 4 DURATION Default settings are listed in bold. SeTTINgS 01 1 SeCoND PULSe 02 LATCHED 10 SEC 03 LATCHED 15 SEC 04 LATCHED 20 SEC 05 LATCHED 30 SEC 06 LATCHED 5 MIN 07 LATCHED 10 MIN 08 RUN TIME LATCH 01 1 SeCoND PULSe 02 LATCHED 10 SEC 03 LATCHED 15 SEC 04 LATCHED 20 SEC 05 LATCHED 30 SEC 06 LATCHED 5 MIN 07 LATCHED 10 MIN 08 RUN TIME LATCH 01 1 SeCoND PULSe 02 LATCHED 10 SEC 03 LATCHED 15 SEC 04 LATCHED 20 SEC 05 LATCHED 30 SEC 06 LATCHED 5 MIN 07 LATCHED 10 MIN 08 RUN TIME LATCH 01 1 SeCoND PULSe 02 LATCHED 10 SEC 03 LATCHED 15 SEC 04 LATCHED 20 SEC 05 LATCHED 30 SEC 06 LATCHED5 MIN 07 LATCHED 10 MIN 08 RUN TIME LATCH 07 - INPUT SOURCE options 01 BRAKE 02 DOOR 03 TACH 04 HOOD 05 TRUNK 06 GLOW PLUG 07 E-BRAKE 08 TEMPERATURE 09 VSS SeTTINgS 02 DATA 03 auto 02 DATA 03 auto 02 DATA 03 auto 02 DATA 03 auto 04 ANALOG INVERTED 02 DATA 03 auto 02 DATA 03 auto 02 DATA 03 auto (TEMP SENSOR) 02 DATA (FROM CAR) 03 auto 01 DISABLE 02 auto

online MoDULe SeTTINgS - 7 OF 7 Page 14 of 17 08 - OUTPUT SOURCE options 01 ARM 02 DISARM 03 LOCK 04 UNLOCK ALL 05 UNLOCK DRIVER DOOR 06 TRUNK 07 LEFT SLIDING DOOR 08 RIGHT SLIDING DOOR 09 PARKING LIGHTS 10 RAP SHUT DOWN 11 PANIC 12 CAR FINDER 13 DEFROST 14 HORN 15 SLEEP STATUS ON LED Default settings are listed in bold. 02 analog/data 02 analog/data 02 analog/data 02 analog/data 02 analog/data 02 analog/data 02 analog/data 02 analog/data 02 analog/data 02 analog/data 02 analog/data 02 analog/data 02 analog/data 02 analog/data 02 ENABLE SeTTINgS

ReMoTe STaRTeR error CoDeS - 1 OF 1 Page 15 of 17 ReMoTe STaRTeR error CoDeS: NoTeS [X] NUMBeR of PaRKINg LIgHT flashes DIagNoSTIC I II WARNING: The following applies only when the parking lights are connected and supported by the system. After a remote starter failure, the parking lights will flash three [3x] times, then will flash [X] number times to indicate an error code. See table. 01 Engine running. 02 Key in ignition at ON position. 03 Door is open. 04 Trunk is open. 05 Foot brake is ON. 06 Hood is open. 07 The reservation is. (Manual transmission only) 08 Tach failure. 09 The vehicle is moving (VSS). 10 System is in Valet Mode. 11 CAN communication failure 12 RS not synchronized. Start vehicle with OEM key for 15 sec before trying a new RS sequence. 13 Bypass problem. ReMoTe STaRTeR SHUTDoWN error CoDeS: NoTeS [Y] NUMBeR of PaRKINg LIgHT flashes DIagNoSTIC I II WARNING: The following applies only when the parking lights are connected and supported by the system. If the engine shuts down after a remote starter sequence: Press and hold the Trunk button and the Start button at the same time for 2.5 seconds when using a 1-WAY remote. OR Press once [1x] on button 4 when using a 2-WAY remote. The parking lights will flash four [4x] times, then will flash [Y] number times to indicate an error code. See table. 01 Engine tach signal is lost. 02 Emergency brake is lost. 03 Foot brake is ON. 04 Hood is open. 05 Engine RPM limiter is ON. 06 Glow plug timeout error. 07 Vehicle is moving (VSS). 08 N/A 09 N/A 10 Door is open. 11 CAN communication failure during RS sequence. 12 RS not synchronized. Start vehicle with OEM key for 15 sec before trying a new RS sequence. 13 Takeover is not allowed. 14 Shutdown error, board overheat protection.

MoDULe DIagNoSTICS - 1 OF 1 Page 16 of 17 TeST MoDULe LeD 1 STaTUS DIagNoSTIC I II III DURING PROGRAMMING DURING REMOTE WITH IGNITION Flashing RED Solid RED Flashing GREEN Solid GREEN then Flashing RED Solid RED Flashing GREEN Solid GREEN then Flashing RED Solid RED Flashing GREEN Solid GREEN then Missing/wrong information from firmware or vehicle. Module waiting for more vehicle information. Additional steps required to complete module programming. Module correctly programmed. No activity or module already programmed. Module incorrectly programmed. Module incorrectly programmed. Module correctly programmed and operational. Reset in progress. Invalid ground when running status from remote starter. Module incorrectly programmed or connected. Module not programmed. Waiting for more vehicle information. False ground when running status from remote starter. Reset in progress. Module at rest and ready for a remote start sequence.

MODULE RESET PROCEDURE - 1 OF 1 Page 17 of 17 >> The following procedure resets the module programming to the vehicle. It does not reset any settings configured online. 06 Module RESET completed. 01 Disconnect all connectors from module except the BLACK 20-PIN connector. 07 Reconnect all connectors. 02 Disconnect the BLACK 20-PIN connector. 08 Repeat programming procedure. 03 PRESS AND HOLD the module s programming button while connecting the BLACK 20-PIN connector. >> Failure to follow procedure may result with a DTC or a CHECK ENGINE error message. 04 Wait, LED 1 will flash RED. RELEASE programming button. 05 LED 1 will turn RED for 2 seconds.

install guide 2000-2006 Mazda MPV STD key AT Document number Revision Date 20151001 firmware ADS-HCX(RST)-MA-[ADS-HCX] hardware ADS-HCX accessories ADS-USB (OPTIONAL) ADS-WLM-AN1/ADS-WLM-AP1 (OPTIONAL) DRONE MOBILE DR-2000 (OPTIONAL) COMPATIBLE RF-KIT (OPTIONAL) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. Please review the Installation Guide carefully before beginning any work.

HARDWIRE / COMPONENT LOCATOR - 1 OF 1 Page 2 of 7 C A D E B F 02A_v1_[W] ADS-HCX(RST)-MA-[ADS-HCX]-EN

HARDWIRE / WIRING DIAGRAM - 1 OF 1 Page 3 of 7 M1 M2 M3 M5 M4 ACCESSORY (+) BLACK/RED 12V (+) WHITE/BLACK IGNITION SWITCH (A) ER (+) BLUE/YELLOW M1 M2 M3 01 ORANGE - ACCESSORY (+) 02 RED - 12V (+) 03 PURPLE - ER (+) 04 PINK/WHITE 05 PINK - IGNITION (+) 06 WHITE 07 RED - 12V (+) 08 BLACK - GROUND 01 GREEN BLACK DOT - LOCK (-) OUTPUT 02 BLUE BLACK DOT - UNLOCK (-) OUTPUT 03 RED/WHITE BLACK DOT 04 GREEN/WHITE BLACK DOT 05 GREEN/BLACK BLACK DOT 06 BLUE/WHITE BLACK DOT 07 EMPTY 08 WHITE/PURPLE BLACK DOT 09 PURPLE/BLACK BLACK DOT 10 WHITE/BLACK BLACK DOT - HORN (-) OUTPUT 11 BROWN/BLACK BLACK DOT 12 WHITE BLACK DOT - PARKING LIGHT (-) OUTPUT 01 BROWN SILVER DOT - BRAKE (+) INPUT 02 BLACK/WHITE SILVER DOT 03 PURPLE SILVER DOT 04 GREEN SILVER DOT 05 PURPLE/WHITE SILVER DOT - TACH (AC) INPUT 06 WHITE/BLUE SILVER DOT 07 GRAY SILVER DOT - HOOD (-) INPUT 08 BLUE SILVER DOT 09 GRAY/BLACK SILVER DOT 10 EMPTY 1K IGNITION (+) BLUE IMMO. (DATA) BLUE/WHITE OR BLUE/BLACK - 05 IGNITION (+) BLACK/WHITE - 07 ARM/DISARM (MUX) LTGREEN - 14 PARKING LIGHT (-) BROWN/WHITE - 13 BRAKE (+) GREEN/YELLOW IMMOBILIZER, NEAR STEERING COLUMN (B) 1 1 2 3 4 5 6 7 8 9 10 11 12 1 DOORLOCK MODULE (C) 1 12 11 10 9 8 7 6 5 4 3 2 1 24 23 22 21 20 19 18 17 16 15 14 13 HEADLAMP SWITCH (D) 1 8 7 6 5 4 3 2 1 16 15 1413 12 11 10 9 BRAKE SWITCH (D) M4 01 EMPTY 02 EMPTY 03 BROWN/RED 04 BROWN/YELLOW 05 BLUE/RED 06 BLUE/YELLOW 07 EMPTY 08 ORANGE 09 YELLOW 10 EMPTY 11 GRAY/RED - IMMOBILIZER (DATA) VEHICLE SIDE 12 GRAY/YELLOW 13 GREEN/RED 14 ORANGE/WHITE 15 BROWN 16 ORANGE/BLACK 17 PINK 18 PURPLE 19 RED 20 BLACK TACH (AC) PURPLE/WHITE DIAGNOSTIC CONNECTOR (F) M5 01 GRAY/BLACK BLUE DOT - IGNITION (+) CONNECTOR SIDE 02 WHITE/BLACK BLUE DOT - IMMO. (DATA) CONNECTOR SIDE 03 GRAY/RED BLUE DOT - IGNITION (+) VEHICLE SIDE 04 WHITE/RED BLUE DOT - IMMO. (DATA) VEHICLE SIDE 05 GRAY BLUE DOT 06 WHITE BLUE DOT HORN (-) HOOD SWITCH 1 02A_v1_[W] ADS-HCX(RST)-MA-[ADS-HCX]-EN INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH ONE. 1

MODULE PROGRAMMING PROCEDURE - 1 OF 1 Page 4 of 7 01 ACC ON Insert key into ignition. 07 Press and release the module s programming button. 02 ACC ON Turn key to position. 08 Release the brake pedal. 03 Wait, LED 1 will turn solid GREEN for 2 seconds. 09 Wait, LED 2 will flash GREEN. 04 ACC ON Turn key to position. 10 Module Programming Procedure completed. 05 ACC ON vehicle for 15 seconds. 06 Press and hold the brake pedal. ADS-HCX(RST)-MA-[ADS-HCX]-EN

TAKEOVER PROCEDURE - STD KEY - 1 OF 1 Page 5 of 7 >> All vehicle doors must be closed and locked prior to remote start sequence. >> Failure to follow procedure will result in vehicle engine shutdown. 01 Press unlock on OEM or aftermarket remote. 02 Insert key into ignition. ACC ON 03 ACC ON Turn key to ON position. 04 Press and release BRAKE pedal. 05 Take over procedure completed. ADS-HCX(RST)-MA-[ADS-HCX]-EN

INSTaLLaTIoN CHeCKLIST - 1 OF 2 Page 6 of 7 CHeCKLIST - WITH aftermarket KeYfoB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 9 Press the /STOP button once [1x] on the aftermarket keyfob to shut down vehicle. 2 Close all vehicle doors, hood and trunk. Question 7: Does the vehicle shut down? 3 Press the LOCK button once [1x] on the aftermarket keyfob. YES: Go to next step. Question 1: Do the doors lock? NO: Repeat step. If problem persists, press the brake pedal once [1x] to shut down the vehicle YES: Go to next step. and call technical support. NO: Verify the remote programming, the RF connections and the wired door lock/unlock 10 RAP and auto light shutdown test connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown? 4 Press the UNLOCK button once [1x] on the aftermarket keyfob. Question 2: Do the doors unlock? YES: Go to next step. NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. 5 Press the TRUNK release button once [1x] on the aftermarket keyfob if supported. Question 3: Does the trunk or hatch open/unlock? YES: Close trunk or hatch and go to next step. NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. 6 Press the AUX 1 button once [1x] on the aftermarket keyfob if supported. Question 4: Does the driver side sliding door open? YES: Press the AUX 1 button once [1x] to close the driver sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists. 7 Press the AUX 2 button once [1x] on the aftermarket keyfob if supported. Question 5: Does the passenger side sliding door open? YES: Press the AUX 2 button once [1x] to close the passenger sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists. 8 Press the /STOP button once [1x] on the aftermarket keyfob to remote start vehicle. Question 6: Does the vehicle remote start? YES: Go to next step. NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call technical support, if the problem persists. YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists. 11 Open hood. 12 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 13 Press the /STOP button once [1x] on the aftermarket keyfob to remote start vehicle. Question 9: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 14 Close hood. 15 Enter vehicle and close the doors. 16 Press the /STOP button once [1x] on the aftermarket keyfob to remote start vehicle. 17 Wait for the vehicle to start. 18 Press brake pedal. Question 10: Does the vehicle shut down? YES: Go to next step. NO: The module does NOT detect the brake pedal signal. Press the /STOP button once [1x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support. 19 Exit vehicle. 20 Installation checklist completed. ADS-HCX(RST)-MA-[ADS-HCX]-EN

INSTaLLaTIoN CHeCKLIST - 2 OF 2 Page 7 of 7 CHeCKLIST - WITH oem KeYfoB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 1: Does the vehicle remote start? YES: Go to next step. NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists. 4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle. Question 2: Does the vehicle shut down? YES: Go to next step. NO: Repeat step. If the problem persists, press on the brake pedal once [1x] to shut down the vehicle and call technical support. 5 RAP Shutdown test Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown? YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists. 6 Open hood. 7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 4: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 9 Close hood. 10 Enter vehicle and close the doors. 11 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. 12 Wait for the vehicle to start. 13 Press brake pedal. Question 5: Does the vehicle shut down? YES: Go to next step. NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support. 14 Exit vehicle. 15 Installation checklist completed. ADS-HCX(RST)-MA-[ADS-HCX]-EN

install guide 2001-2004 Mazda Miata STD key AT Document number Revision Date 20151001 firmware ADS-HCX(RST)-MA-[ADS-HCX] hardware ADS-HCX accessories ADS-USB (OPTIONAL) ADS-WLM-AN1/ADS-WLM-AP1 (OPTIONAL) DRONE MOBILE DR-2000 (OPTIONAL) COMPATIBLE RF-KIT (OPTIONAL) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. Please review the Installation Guide carefully before beginning any work.

HARDWIRE / COMPONENT LOCATOR - 1 OF 1 Page 2 of 7 C A B D E 01A_v1_[W] ADS-HCX(RST)-MA-[ADS-HCX]-EN

HARDWIRE / WIRING DIAGRAM - 1 OF 1 Page 3 of 7 M1 M2 M3 M5 M4 ACCESSORY (+) BLACK/RED 12V (+) WHITE/RED IGNITION SWITCH (A) ER (+) WHITE/BLACK M1 M2 01 ORANGE - ACCESSORY (+) 02 RED - 12V (+) 03 PURPLE - ER (+) 04 PINK/WHITE 05 PINK - IGNITION (+) 06 WHITE - PARKING LIGHT (+) 07 RED - 12V (+) 08 BLACK - GROUND 01 GREEN BLACK DOT - LOCK (-) OUTPUT 02 BLUE BLACK DOT - UNLOCK (-) OUTPUT 03 RED/WHITE BLACK DOT - TRUNK (-) OUTPUT 04 GREEN/WHITE BLACK DOT 05 GREEN/BLACK BLACK DOT 06 BLUE/WHITE BLACK DOT 07 EMPTY 08 WHITE/PURPLE BLACK DOT 09 PURPLE/BLACK BLACK DOT 10 WHITE/BLACK BLACK DOT - HORN (-) OUTPUT 11 BROWN/BLACK BLACK DOT 12 WHITE BLACK DOT 1K IGNITION (+) BLUE IMMO. (DATA) RED/BLACK - 05 IGNITION (+) BLACK/WHITE - 07 ARM/DISARM (MUX) RED/BLUE - 09 PARKING LIGHT (+) RED/BLACK TRUNK RELEASE (-) RED/WHITE 1 1 2 3 4 5 6 7 8 9 10 11 12 1 5 4 3 2 1 12 11 10 9 8 7 6 IMMOBILIZER, NEAR STEERING COLUMN (B) 1 DOORLOCK MODULE (C) DRIVER KICK PANEL (D) M3 01 BROWN SILVER DOT - BRAKE (+) INPUT 02 BLACK/WHITE SILVER DOT 03 PURPLE SILVER DOT 04 GREEN SILVER DOT 05 PURPLE/WHITE SILVER DOT - TACH (AC) INPUT 06 WHITE/BLUE SILVER DOT 07 GRAY SILVER DOT - HOOD (-) INPUT 08 BLUE SILVER DOT 09 GRAY/BLACK SILVER DOT 10 EMPTY BRAKE (+) GREEN TACH (AC) GREEN/TAN DIAGNOSTIC CONNECTOR (E) M4 01 EMPTY 02 EMPTY 03 BROWN/RED 04 BROWN/YELLOW 05 BLUE/RED 06 BLUE/YELLOW 07 EMPTY 08 ORANGE 09 YELLOW 10 EMPTY 11 GRAY/RED - IMMOBILIZER (DATA) VEHICLE SIDE 12 GRAY/YELLOW 13 GREEN/RED 14 ORANGE/WHITE 15 BROWN 16 ORANGE/BLACK 17 PINK 18 PURPLE 19 RED 20 BLACK M5 01 GRAY/BLACK BLUE DOT - IGNITION (+) CONNECTOR SIDE 02 WHITE/BLACK BLUE DOT - IMMO. (DATA) CONNECTOR SIDE 03 GRAY/RED BLUE DOT - IGNITION (+) VEHICLE SIDE 04 WHITE/RED BLUE DOT - IMMO. (DATA) VEHICLE SIDE 05 GRAY BLUE DOT 06 WHITE BLUE DOT HORN (-) HOOD SWITCH 1 01A_v1_[W] ADS-HCX(RST)-MA-[ADS-HCX]-EN INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH ONE. 1

MODULE PROGRAMMING PROCEDURE - 1 OF 1 Page 4 of 7 01 ACC ON Insert key into ignition. 07 Press and release the module s programming button. 02 ACC ON Turn key to position. 08 Release the brake pedal. 03 Wait, LED 1 will turn solid GREEN for 2 seconds. 09 Wait, LED 2 will flash GREEN. 04 ACC ON Turn key to position. 10 Module Programming Procedure completed. 05 ACC ON vehicle for 15 seconds. 06 Press and hold the brake pedal. ADS-HCX(RST)-MA-[ADS-HCX]-EN

TAKEOVER PROCEDURE - STD KEY - 1 OF 1 Page 5 of 7 >> All vehicle doors must be closed and locked prior to remote start sequence. >> Failure to follow procedure will result in vehicle engine shutdown. 01 Press unlock on OEM or aftermarket remote. 02 Insert key into ignition. ACC ON 03 ACC ON Turn key to ON position. 04 Press and release BRAKE pedal. 05 Take over procedure completed. ADS-HCX(RST)-MA-[ADS-HCX]-EN

INSTaLLaTIoN CHeCKLIST - 1 OF 2 Page 6 of 7 CHeCKLIST - WITH aftermarket KeYfoB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 9 Press the /STOP button once [1x] on the aftermarket keyfob to shut down vehicle. 2 Close all vehicle doors, hood and trunk. Question 7: Does the vehicle shut down? 3 Press the LOCK button once [1x] on the aftermarket keyfob. YES: Go to next step. Question 1: Do the doors lock? NO: Repeat step. If problem persists, press the brake pedal once [1x] to shut down the vehicle YES: Go to next step. and call technical support. NO: Verify the remote programming, the RF connections and the wired door lock/unlock 10 RAP and auto light shutdown test connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown? 4 Press the UNLOCK button once [1x] on the aftermarket keyfob. Question 2: Do the doors unlock? YES: Go to next step. NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. 5 Press the TRUNK release button once [1x] on the aftermarket keyfob if supported. Question 3: Does the trunk or hatch open/unlock? YES: Close trunk or hatch and go to next step. NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. 6 Press the AUX 1 button once [1x] on the aftermarket keyfob if supported. Question 4: Does the driver side sliding door open? YES: Press the AUX 1 button once [1x] to close the driver sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists. 7 Press the AUX 2 button once [1x] on the aftermarket keyfob if supported. Question 5: Does the passenger side sliding door open? YES: Press the AUX 2 button once [1x] to close the passenger sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists. 8 Press the /STOP button once [1x] on the aftermarket keyfob to remote start vehicle. Question 6: Does the vehicle remote start? YES: Go to next step. NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call technical support, if the problem persists. YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists. 11 Open hood. 12 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 13 Press the /STOP button once [1x] on the aftermarket keyfob to remote start vehicle. Question 9: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 14 Close hood. 15 Enter vehicle and close the doors. 16 Press the /STOP button once [1x] on the aftermarket keyfob to remote start vehicle. 17 Wait for the vehicle to start. 18 Press brake pedal. Question 10: Does the vehicle shut down? YES: Go to next step. NO: The module does NOT detect the brake pedal signal. Press the /STOP button once [1x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support. 19 Exit vehicle. 20 Installation checklist completed. ADS-HCX(RST)-MA-[ADS-HCX]-EN

INSTaLLaTIoN CHeCKLIST - 2 OF 2 Page 7 of 7 CHeCKLIST - WITH oem KeYfoB 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 2 Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 1: Does the vehicle remote start? YES: Go to next step. NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists. 4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle. Question 2: Does the vehicle shut down? YES: Go to next step. NO: Repeat step. If the problem persists, press on the brake pedal once [1x] to shut down the vehicle and call technical support. 5 RAP Shutdown test Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown? YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists. 6 Open hood. 7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 4: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 9 Close hood. 10 Enter vehicle and close the doors. 11 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. 12 Wait for the vehicle to start. 13 Press brake pedal. Question 5: Does the vehicle shut down? YES: Go to next step. NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support. 14 Exit vehicle. 15 Installation checklist completed. ADS-HCX(RST)-MA-[ADS-HCX]-EN