PETROL CHAINSAW - THPCS18 30/06/2014 v2
CONTENTS 12-14 15 2
3
PULL CHAIN OIL MAX MIN The indication regarding the chain oil adjuster nut. MIN direction - the oil flow decreases MAX direction- the oil flow increases Position: bottom of the clutch side 46 550 260 WPL7RTM with adjuster 7T X 0.325" 410 x 235 x 265 (mm) 7.5 (kg) Sprocket nose - 18" (45cm) 21VB 0.325 (in) 0.058 (in) 4
Your chainsaw package contains: a Power Unit and separate Side Cover, Guide Bar, Saw Chain, Scabbard, Plug Wrench and Screwdriver for carburettor adjustment. Wearing gloves locate the guide bar onto the chainsaw making sure that the hole on either side of the slot locates over the adjuster pin. Tighten the nuts securely with the bar tip held up. Using gloves, check the chain for smooth rotation and correct tension while moving by hand. You should be able to pull the chain 5-6mm off the guide bar. If necessary re-adjust by loosening the side cover nuts. A new chain will stretch during its first use. Turn off the engine then check and readjust the chain frequently. Maintaining chain tension is important, incorrect tension can cause the bar to wear and the chain to come off. FUEL Petrol is very flammable. Do not smoke while using the chainsaw or refuel near a flame or spark. Allow the engine the cool before refuelling. Refuel the engine at least 3m away from your work area. Use a ratio of 25:1 unleaded petrol to 2-stroke mineral oil. For semi-synthetic or synthetic use the manufacturer s ratio. Mix in an appropriate mixing bottle. Unscrew the fuel cap, and fuel the machine to 80% capacity (248ml). Fasten the fuel cap tightly and wipe up any spillage. Ensure that any stored petrol/oil mixture (2-stroke) is clearly marked in a separate can and only stored for 4-6 weeks. If the chainsaw is not going to be used for a long period, drain the mixture from the fuel tank, then start the engine to use up any remaining fuel. CHAIN OIL Use Handy chain oil HP-177. 5
The chain oil flow can be adjusted by inserting a screwdriver in the hole on the bottom of the machine. Adjust accoring to your work conditions 1 6
7
8 to pull it out by
Before cleaning, inspecting or repairing the chainsaw, ensure that the engine has stopped and is cool. Disconnect the spark plug to prevent accidental starting.. 9
3/16in (4.76mm) e 21VB 21VB 0.25 (0.65mm) 21VB 0.25 (0.65mm) Chain fi les can be purchased from Handy Garden Machinery on 01793 333203, under the product code HP-107. 850 10
11
PARTS DIAGRAM 12
PARTS LIST No Part No Description Qty No Part No Description Qty 1 WPL7RTM Spark Plug 1 58 TH206-58 Foam Seal 1 2 TH206-2 Board 1 59 TH206-59 Small Oil Seal 15x28x5 1 3 TH206-3 Bolt M5x14 5 60 TH206-60 Snap Ring 1 4 TH206-4 Cover 1 61 TH206-61 Vent Filter 1 5 TH206-5 Switch Block 1 62 TH206-62 Air Outlet Connector 1 6 TH206-6 Nut M5 2 63 TH206-63 Plug Pad 3 7 TH206-7 Muffler Cover 1 64 TH206-64 Rubber Cushion Pad 3 8 TH206-8 Bolt M5x10 2 65 TH206-65 Bar Plate 1 9 TH206-9 Muffler 1 66 TH206-66 Bolt M4x10 1 10 TH206-10 Muffler Gasket 1 67 TH206-67 Right Pad 2 11 TH206-11 Muffler Bolt 2 68 TH206-68 Right Pad Rubber Cushion 1 12 TH206-12 Bolt M5x20 4 69 TH206-69 Right Crank Case 1 13 TH206-13 Cylinder 1 70 TH206-70 Pin 6x10 3 14 TH206-14 Gylinder Gasket 1 71 TH206-71 Bearing 6202 2 15 TH206-15 Piston Ring 2 72 TH206-72 Snap Ring 2 16 TH206-16 Piston Ring 1 73 TH206-73 Small Bearing 1x15x12.5 1 17 TH206-17 Snap Ring 2 74 TH206-74 Crankshaft Conrod Assembly 1 18 TH206-18 Piston Pin 1 75 TH206-75 Flywheel Key 3.3x7x10 1 19 TH206-19 Carburetor Gasket 1 76 TH206-76 Gasket 1 20 TH206-20 Chain Catcher 1 77 TH206-77 Hose Spring Clip 1 21 TH206-21 Bolt M4x14 1 78 TH206-78 Hose Pulse 1 22 TH206-22 Plastic Ring 1 79 TH206-79 Hose Pulse Spigot 1 23 TH206-23 Damping Spring 1 80 TH206-80 Bolt M5x12 1 24 TH206-24 Bolt ST4.8x16 3 81 TH206-81 Wire Clamp 1 25 TH206-25 Intake Gasket 1 82 TH206-82 Boot Carburetor 1 26 TH206-26 Intake 1 83 TH206-83 Snap Ring 35 1 27 TH206-27 Bolt M5x14 2 84 TH206-84 Outer Gromet 1 28 TH206-28 Bolt M5x14 2 85 TH206-85 Left Crankcase 1 29 TH206-29 Carburetor Support 1 86 TH206-86 Left Pad Rubber Cushion 1 30 TH206-30 Carburetor Support Gasket 1 87 TH206-87 Bolt M5x30 2 31 TH206-31 Carburetor Flange 1 88 TH206-88 Bolt M5x25 3 32 TH206-32 Carburetor Eyelet 1 89 TH206-89 Large Oil Seal 15x35x5 1 33 TH206-33 Carburetor Assembly 1 90 TH206-90 Oil Cap Stopper 2 34 TH206-34 Inner Gromet 1 91 TH206-91 Oil Cap Rubber Washer 1 35 TH206-35 Rubber Cap 1 92 TH206-92 Oil Tank Cap 1 36 TH206-36 Bolt M5x50 2 93 TH206-93 Oil Seal Gasket Plate 1 37 TH206-37 Air Filter 1 94 TH206-94 Bolt M4x6 2 38 TH206-38 Air Filter Cover 1 95 TH206-95 Flywheel Assembly 1 39 TH206-39 Nylon Gasket 1 96 TH206-96 Snap Ring Spring 8 1 40 TH206-40 Air Filter Knob 1 97 TH206-97 Nut M8x1 1 41 TH206-41 Stud Bar M8x24 2 98 TH206-98 Bolt ST4.8x12 1 42 TH206-42 Clutch Frame 1 99 TH206-99 Washer 5x16 1 43 TH206-43 Clutch Spring 1 100 TH206-100 Starter Assembly 1 44 TH206-44 Clutch 3 101 TH206-101 Starter Spring Cover 1 45 TH206-45 Clutch Washer 1 102 TH206-102 Starter Spring Cover 1 46 TH206-46 Clutch Drum 1 103 TH206-103 Outer Gromet 1 47 TH206-47 Sprocket 1 104 TH206-104 Recoil Housing 1 48 TH206-48 Needle Bearing 1 105 TH206-105 Bolt M5x14 4 49 TH206-49 Worm Gear 1 106 TH206-106 Rope Snap 1 50 TH206-50 Choke Knob Washer 1 107 TH206-107 Inner Ring 2 51 TH206-51 Choke Knob 1 108 TH206-108 Recoil Spring 1 52 TH206-52 Choke Knob Damper 1 109 TH206-109 Recoil Handle 1 53 TH206-53 Bolt M5x12 3 110 TH206-110 Recoil Rope 1 54 TH206-54 Oil Pump Cover 1 111 TH206-111 Front Handle 1 55 TH206-55 Oil Outlet Hose 1 112 TH206-112 Bolt ST4.8x16 4 56 TH206-56 Bolt M4x12 2 113 TH206-113 Bolt M5x20 2 57 TH206-57 Oil Pump 1 114 TH206-114 Ignition Coil Assembly 1 13
PARTS LIST No Part No Description Qty No Part No Description Qty 115 TH206-115 Air Baffle 1 150 TH206-150 Brake Lever 1 116 TH206-116 Oil Hose 1 151 TH206-151 Pin 3X8 1 117 TH206-117 Oil Filter 1 152 TH206-152 Brake Band 1 118 TH206-118 Fuel Tank Cap 1 153 TH206-153 Spring Actuator 1 119 TH206-119 Fuel Tank Cap Rubber Washer 1 154 TH206-154 Spring Actuator 1 120 TH206-120 Primer Bulb & Pipes Assembly 5 155 TH206-155 Brake Plate 1 121 TH206-121 Large Plug 2 156 TH206-156 Pin 1 122 TH206-122 Nut 2 157 TH206-157 Bolt ST4.2x9.5 2 123 TH206-123 Large Plug Housing 2 158 TH206-158 Adjustor Cover 1 124 TH206-124 Pin 1 159 TH206-159 Rubber Strap 1 125 TH206-125 Trigger Lever (142) 1 160 TH206-160 Chain Adjustor Sprocket 1 126 TH206-126 Trigger Spring 1 161 TH206-161 Chain Tooth Adjustor 1 127 TH206-127 Double Screw Cushion 1 162 TH206-162 Adjustor Pin 1 128 TH206-128 Fuel Tank 1 163 TH206-163 Pin 1 129 TH206-129 Throttle Rod 1 164 TH206-164 Snap Ring 3 2 130 TH206-130 Balance Cap 1 165 TH206-165 Brake Plate 1 131 TH206-131 Balance 1 166 TH206-166 Gasket Ring 1 132 TH206-132 Balance Cover 1 167 TH206-167 Snap Ring 4 1 133 TH206-133 Balance Support 1 168 TH206-168 Gasket Ring 6X18 1 134 TH206-134 Fuel Filter 1 169 TH206-169 Brake Spring 1 135 TH206-135 Fuel Pipe Ring 1 170 TH206-170 Chain Brake Lever 1 136 TH206-136 Fuel Pipe 1 1 171 TH206-171 Pin 1 137 TH206-137 Inlet Pipe 1 172 TH206-172 Chain Brake Housing 1 138 TH206-138 Fuel Pipe 2 1 173 TH206-173 Rubber Plate 1 139 TH206-139 Fuel Return Pipe 1 174 TH206-174 Flange Nut M8 2 140 TH206-140 Fuel Support Pipe 1 175 TH206-175 Bolt M5x10 2 141 TH206-141 Rear Handle 1 176 TH206-176 Spike 1 142 TH206-142 Trigger Lever (125) 1 177 TH206-177 Oregon 18" Guide Bar 1 143 TH206-143 Cover 1 178 TH206-178 Oregon 18" Chain 1 144 TH206-144 Primer Bulb 1 ZC1 TH206-ZC1 Crankshaft Assembly 1 145 TH206-145 Ignition Switch 1 ZC2 TH206-ZC2 Recoil Assembly 1 146 TH206-146 Bolt ST4.8x19 1 ZC3 TH206-ZC3 Clutch Assembly 1 147 TH206-147 Rubber Dustproof Plate 1 ZC4 TH206-ZC4 Chain Brake Assembly 1 148 TH206-148 Screw ST4.2x9.5 4 ZC5 TH206-ZC5 Balance Assembly 1 149 TH206-149 Brake Spring Cover 1 14
EC Declaration of Conformity We, Importer Handy Distribution SN3 4NS Declare that the product Designation: 46cc PETROL CHAINSAW Model: THPCS18 Complies with the following directives: 2006/42/EC / Annex IV - Machinery Directive 2004/108/EC - Electromagnetic Compatibility Directive 2000/14/EC amended by 2005/88/EC - Noise Emission in the Environment by Equipment for Use Outdoors Directive. The conformity assessment procedure followed was in accordance with Directive 2006/42/EC Name of the Notified Body: TÜV SÜD Product Service GmbH Address: Ridlerstraße 65-80339 München - Measured Sound Pressure Level: 96.7 db (A) - Guaranteed Sound Power Level: 110 db (A) Standards and technical specifications referred to: 2006/42/EC / Annex IV - EN 954-1, ISO 6531:2008, ISO 6533:2001, ISO 6534, ISO 6535, ISO 7293, ISO 7914, ISO 7915, ISO 8334, ISO 9518, ISO 10726:1992, ISO 11680, EN ISO 11681-1, EN ISO 11681-1A:2011, ISO 11684:1995, ISO/TR 11688-1, ISO/TR 11688-2, ISO 11691, ISO 11820, EN 12100-1, ISO 12100:2010, ISO 13772, ISO 13849-1:2006, EN ISO 13849-2, ISO 13857: 2008, EN ISO 14121-1:2007, ISO 14163, ISO 14982:1998, ISO 17080:2005, ISO 22867, ISO 22868, IEC60745-1:2006, EN60825, EN 62061, ZEK 01.4-08/11.11 Authorised signatory and technical file holder Date: 21/03/2014 Signature: Name / title: Mr. Simon Belcher / Managing Director Hobley Drive, Stratton St Margaret, Swindon, Wiltshire, SN3 4NS. 15
GUARANTEE This product is guaranteed against manufacturing defects for a period of 12 months. This does not cover the product where the fault is due to misuse, abuse, use in contravention of the instructions, or where the product has been the subject of unauthorised modifications or alterations. This warranty only covers domestic use and will be void if the tool is used for a commercial application. In the event of a problem with the product within the guarantee period, please contact Customer Service on 01793 333212 or email customerservice@handydistribution.co.uk. If the issue cannot be resolved over the telephone or by email, you may be referred to your local approved service dealer. Please keep your sales receipt as proof of purchase Your statutory rights remain unaffected. Guarantor: Handy Distribution SN3 4NS Whilst every effort is made to accurately represent the product, small variations in colour, design and specification may occur. We reserve the right to alter the product without giving notice. All images are illustrative only and may differ from the product due to ongoing product development. 16
A SELECTION OF QUALITY PRODUCTS FROM OUR VAST RANGE HAND PUSH LAWN MOWERS ELECTRIC & PETROL BLOW VACS ELECTRIC & PETROL SHREDDERS ELECTRIC, PETROL & MANUAL LOG SPLITTERS LAWN SWEEPERS PETROL LINE TRIMMERS PETROL BRUSHCUTTERS PETROL MULTICUTTERS ELECTRIC & PETROL CHAINSAWS LOG SAW HORSES CORDLESS & PETROL HEDGETRIMMERS ELECTRIC & PETROL TILLERS AERATORS & DETHATCHERS GARDEN & SALT SPREADERS PUSH & TOWED ROLLERS SNOW CLEARANCE TOOLS SPRAYERS SACK TRUCKS TROLLEYS & TRAILERS LIGHT CONSTRUCTION FIND OUT MORE AT WWW.THEHANDY.CO.UK 17
NOTES 18
19
To order spare parts and see the complete range of garden machinery and garden equipment from Handy, visit: www.thehandy.co.uk Spares & Support: 01793 333212