AL SL O. Workshop manual. BPW air suspensions, series AL / SL / O. BPW-WH-AL-SL-O e

AL SL O Workshop manual BPW air suspensions, series AL / SL / O BPW-WH-AL-SL-O 35391601e

Page 2 BPW-WH-AL-SL-O 35391601e BPW-WH-AL-SL-O 35391601e Page 3 Contents Valid: 01.02.2016 1. Product identification... Page 4 1.1 Explanation of BPW axle type codes (extract) Page 4 1.2 Explanation of BPW code numbers (extract) Page 6 2. Special tools... Page 8 3. Exploded view / name... Page 10 4. Tightening torques... Page 15 5. Safety regulations, safety information... Page 16 5.1 Safety regulations Page 16 5.2 Safety information Page 17 6. Care and maintenance... Page 18 7. Dismantling and assembly of axle and trailing arms... Page 32 8. Dismantling and assembly of trailing arm... Page 42 8.1 Dismantling trailing arm Page 42 8.2 Fit trailing arm springs Page 44 8.2.1 Fit trailing arm springs (air suspension overslung) Page 46 8.2.2 Fit trailing arm springs (air suspension underslung) Page 49 8.3 Fit trailing arm springs (air suspension overslung and underslung) Page 53 8.4 Change steel / rubber / steel bushes Page 56 9. Dismantling and assembly of U-stabiliser... Page 57 9.1 Dismantling of U-stabiliser Page 57 9.2 Installation of U-stabiliser Page 59 10. Dismantling and assembly of air bags... Page 61 10.1 Dismantling of air bags Page 61 10.2 Assembly of air bags Page 63 10.3 Dismantling of air bags, assembling - Air bag with universal plate Page 65 10.4 Dismantling of air bags, assembling - Air bag with central bolt connection Page 66 10.5 Dismantling of air bags, assembling - Air bag with steel piston Page 67 10.6 Dismantling of air bags, assembling - Combi Air bag Page 68 10.7 Dismantling of air bags, assembling - Airlight Direct Page 69 11. Dismantling and assembly of shock absorbers... Page 70 12. Detaching and attaching check straps... Page 73 13. Dismantling and assembly of axle lift device... Page 74 13.1 Lateral and central axle lift device Page 74 13.2 Double-sided axle lift with adjustable hanger, trailing arm 70 mm wide Page 80 13.3 Double-sided axle lift with fi xed and adjustable hanger, trailing arm 100 mm wide Page 84 13.4 Double-sided axle lift with adjustable, bolted hanger SLO / SLM series Page 89 14. Air levelling valve... Page 94 15. Shut-off valve... Page 96 16. Axle alignment check... Page 97 16.1 Conventional axle alignment on the vehicle Page 97 16.2 Axle alignment check with laser measuring devices Page 102 17. Other inspection operations... Page 103 - Refer to appropriate workshop manuals for axle repairs Subject to change without notice. Current versions and additional information can be found online at www.bpw.de.

Page 4 BPW-WH-AL-SL-O 35391601e BPW-WH-AL-SL-O 35391601e Page 5 1 Product identification 1.1 Explanation of BPW axle type codes (extract) Example H S F H SLO A LL 3/ 9010 /12 A F30 ECO Axle series Brake H H.. SN 420 K K.. SN 360 N N.. SN 300 SH SH.. SB 4309 /SB 4345; TSB 4309 / TSB 4312 SK SK SB 3745; TSB 3709 B For single wheels, wheels with off set S For single wheels, wheels without off set Z For twin wheels I Wheel spiders for TRILEX wheel rims, single wheels IZ Wheel spiders for TRILEX wheel rims, twin wheels F Wheel studs M 22 x 1.5 without wheel nuts, order wheel nuts for stud or spigot alignment separately M For spigot alignment / Aluminium wheel connection H For hanging boosters Air suspension series Ride height O O = straight overslung trailing arm 490-500 OM OM = cranked overslung trailing arm 370-470 OMN OMN = cranked overslung trailing arm 355 OMT OMT = cranked underslung trailing arm 290 OT OT = underslung trailing arm 220-330 SLO SLO = straight overslung trailing arm 420-490 SLM SLM = cranked overslung trailing arm 360-440 SLU SLU = underslung trailing arm 220-330 ALO ALO = straight overslung trailing arm 380-490 ALM ALM = cranked overslung trailing arm 305-420 ALMT ALMT = cranked overslung trailing arm 245-290 ALU ALU = underslung trailing arm 175-300 DLU DLU = Airlight Direct 260-330 A With axle lift device R With frame (= ride height + 100 mm) U With U-stabiliser L With steering axle, series L - steering angle max. 40 LL With self-steering axle, series LL - steering angle max. 20 Example H S F H SLO A LL 3/ 9010 /12 A F30 ECO - Single axle 2 / Tandem axle suspension 3 / Tri-axle suspension 6006 Axle load (kg) + quantity of wheel studs per hub to 13010 /12 to /40 A C D E G K S T V X Y Steering angle of steering axle Alloy hanger brackets Integrated support Hanger brackets with top plate Hanger brackets without top plate Air bags with split piston Bolted on hanger brackets Taper mounted hanger brackets (70 mm wide) With support (trailing axle) Adjustable hanger brackets With stainless steel hanger brackets Without mounted hanger brackets, hanger brackets separate 30 Air bag Ø 300 mm, for stroke 200 mm (standard) 30-1 Air bag Ø 300 mm, for stroke up to 340 mm 30 K Air bag Ø 300 mm, for stroke 150 mm 36 Air bag Ø 360 mm, for stroke 200 mm (standard) 36-1 Air bag Ø 360 mm, for stroke up to 340 mm 36-2 Air bag Ø 360 mm, for stroke up to 450 mm 36 K Air bag Ø 360 mm, for stroke 180 mm F30 Air bag Ø 300 mm, central on the trailing arm Z Without mounted air bags, air bags separate ECO Plus 3 Weight optimised trailer axle with ECO Plus 3 Unit ECO Plus 2 Weight optimised trailer axle with ECO Plus 2 Unit ECO Plus Weight optimised trailer axle with ECO Plus Unit ECO Trailer axle with ECO Unit ECO-MAXX Weight optimised trailer axle with ECO Unit MAXX Weight optimised trailer axle with helical fit wheel bolts

Page 6 BPW-WH-AL-SL-O 35391601e BPW-WH-AL-SL-O 35391601e Page 7 1 Product identification 1.2 Explanation of BPW axle code numbers (extract) Example: 61. 38. 441. 001 1. + 2. digit 21. Air suspension single axle 28. 30. 38. Air suspension single axle without air bags, air bags loose, separate 61. Air suspension single axle 64. 67. 22. Tandem axle air suspension 32. Tandem axle air suspension / tri-axle air suspension 62. Tandem axle air suspension 65. 68. 23. Tri-axle air suspension 29. 39. 63. Tri-axle air suspension 66. 69. 3. + 4. digit: axle load and bearing Axle load Roller bearing Bearing generation 06. 6500 kg 33116 / 32310 Conventional hub bearing 08. 8000-9000 kg 33116 / 32310 Conventional hub bearing 10. 10000-12000 kg 33118 / 32313 Conventional hub bearing 14. 13000-14000 kg 32219 / 33215 Conventional hub bearing 36. 6500 kg 33116 / 32310 ECO Unit 37. 8000-9000 kg 33116 / 32310 ECO Unit 38. 39. 40. 10000-12000 kg 33118 / 32313 ECO Unit 41. 44. 13000-14000 kg 32219 / 33215 ECO Unit 47. 8000-9000 kg 33118 / 32313 ECO Plus Unit 48. 49. 50. 10000-12000 kg 33118 / 32313 ECO Plus Unit 51. 57. 8000-9000 kg 33118 / 32313 ECO Plus 2 Unit 58. 59. 65. 6400 kg 32215 / 32310 Conventional hub bearing 68. 8000-9000 kg 33118 / 32313 ECO Plus 3 Unit Example: 61. 38. 441. 001 001. to 099 220. to 509 501. to 509. 000 to 999 5. - 7. digit Premounted air suspension axle without hanger brackets and air bags in the case of ref. number 61.xx.xxx.xxx - 69.xx.xxx.xxx e.g.:.0xx. = Premounted air suspension axle.x51. = Premounted air suspension axle with trailing arm 05.082.13.51.0 Designation of ride height and air bag type 220 to 509 in the case of ref. number 61.xx.xxx.xxx - 69.xx.xxx.xxx e.g.:.22x. = 220 mm ride height.44x. = 440 mm ride height Air bag type:.xx0. = BPW 30 (Ø 300 mm).xx1. = BPW 36 (Ø 300 mm).xx2. = BPW 36-1 (Ø 300 mm).xx3. = BPW 30-1 (Ø 300 mm).xx4. = BPW 30 K (Ø 300 mm).xx5. = BPW 36 K (Ø 300 mm).xx6. = BPW 36-2 (Ø 300 mm).xx9. = BPW 30 / 36 loose separately Designation of wheel brake in the case of ref. number 20. - 39... For explanations on the item number, refer to the corresponding axis 8. - 10. digit: consecutive number Consecutive number 000-999

Page 8 BPW-WH-AL-SL-O 35391601e BPW-WH-AL-SL-O 35391601e Page 9 2 Special tools Number Description Illustration of tool Tool in operation Number Description Illustration of tool Tool in operation 1 Assembly tool for removal and installation of rubber-steel bushes Ø 50-60 mm 5 Measuring tube for aligning axles and suspension units BPW code number: BPW code number: 14.825.11744 15.001.01609 15.005.01609 2 Press tool for installation of rubber-steel bushes in anti-roll bars (U-shaped) BPW code number: 15.002.19433 Ø 52.6 15.003.19433 Ø 60 3 Press tool for installation of steel-rubbersteel bushes BPW code number: 03.084.37.10.0 Ø 30 03.084.37.11.0 Ø 24 4 Threaded adapter for aligning axles and suspension units. BPW code number: Conventional hub bearing 15.013.01609 M 115 x 2 6.5-9 t 15.014.01609 M 125 x 2 10-12 t 15.012.01609 M 135 x 3 13-14 t 16.008.01609 M 155 x 3 16-18 t ECO Unit 15.020.01609 M 125 x 2 6.5-9 t 15.021.01609 M 135 x 2 10-12 t (old) 15.023.01609 M 136 x 2.5 10 t (new) ECO Plus Unit 15.023.01609 M 136 x 2.5 8-12 t ECO Plus 3 Unit 15.021.01609 M 135 x 2

Page 10 BPW-WH-AL-SL-O 35391601e BPW-WH-AL-SL-O 35391601e Page 11 3 Exploded view

BPW-WH-AL-SL-O 35391601e Page 12 BPW-WH-AL-SL-O 35391601e Page 13 3 Exploded view

Page 14 BPW-WH-AL-SL-O 35391601e BPW-WH-AL-SL-O 35391601e Page 15 Name Tightening torque 4 Item Name 25 Centering frame 1000 Trailing arm 1005 Bush 1012 Locking plate 1015 Plug 1018 Spring screw (2-leaf trailing arm) 1019 Hexagon nut (2-leaf trailing arm) 1024 Spring pad, Double latch 1026 Spring pad 1027 Spring pad 1032 Spring plate 1033 Spring plate 1035 Segment 1035 Spring pad 1040 Centering bolt 1041 Tracking plate 1042 Centering plate, Centering ring 1050 Spring U-bolt 1053 Hexagon screw 1055 Washer 1055 Ring 1057 Nut M 22 1154 Spring bolt 1160 Slider 1161 Plate (adjusting plate) 1165 Washer 1168 Lock nut 1300 Shock absorber 1303 Bush 1304 Rubber bump stop 1310 Thread bolt 1315 Hexagon screw 1318 Ring 1324 Hexagon screw 1327 Spacer sleeves 1330 Lock nut M 24 1510 Hanger bracket, rigid 1511 Hanger bracket, adjustable 1525 Shaped plate (wearing plate) 1530 Disc (aluminium hanger bracket) 1531 Disc (aluminium hanger bracket) 1535 Bush 1540 Bush 1570 Hexagon screw 1571 Hexagon nut 1575 Knurled screw 1576 Washer 1577 Lock nut U-stabiliser 1156 Hexagon screw 1168 Lock nut 1637 Lock nut 1641 Bush with seals 1642 Shaped plate 1643 Grease nipple 1645 Hexagon screw 1815 U-Bolt 1817 Bush 1820 Support Air bag 1200 Air bag assembly 1205 Air bag 1210 Piston 1210 Piston support (version AD) 1212 Hanger bracket (version KA) 1213 Piston 1215 Threaded sleeve (version GG) 1215 Bolt (version ZS, SG) 1216 Ring 1218 Nut (version KA) 1218 Shaped part (version AD) 1219 Screw 1220 Plate (version GG) 1220 Washer (version SG) 1222 Locking screw 1224 Locking screw 1240 Lock nut 1243 Spring washer 1244 Shaft nut Check strap attachments with threaded bolt 1360 Catch strap 1362 Threaded bolt 1368 Shaped plate 1370 Hexagon nut 1375 Return spring with split pins 1360 Catch strap 1362 Bolt 1368 Washer 1371 Split pin 1375 Return spring Lateral and central axle lift device 1024 Spring pad 1050 Spring U-bolt 1055 Washer 1156 Hexagon screw (spring bolt) 1161 Plate (adjusting plate) 1165 Washer 1168 Lock nut 1175 Bush 1180 Bush 1200 Air bag assembly 1224 Locking screw 1225 Hexagon screw 1240 Lock nut 1330 Lock nut M 24 1525 Shaped plate (wearing plate) 1560 Connecting link disc with anti-rotation device 1600 Support 1605 Tube 1610 Lifting arm 1615 Support 1635 Bump stop 1636 Hexagon screw Two-side axle lift 1156 Spring bolt 1161 Plate (adjusting plate) 1168 Lock nut 1175 Bush 1180 Bush 1525 Shaped plate (wearing plate) 1570 Hexagon screw 1571 Hexagon nut 1610 Shaped plate 1610 Support 1611 Support 1613 Shaped plate 1615 Lever 1620 Bump stop 1621 Cylinder head screw 1623 Lock nut 1630 Square bar 1631 Locking screw 1632 Plate 1635 Locking screw 1636 Lock nut 1660 Diaphragm cylinder for axle lift 1663 Hexagon nut Item Description Thread / Spanner size 1057 Locking nut of Ubolts M 22 / SW 32 1330 M 24 / SW 36 1168 Locking nut of spring pivot bolt or hexagon bolt on axle lift device Airlight II from 08/2001 up to 07/2001 channel crossmember Locking nut of securing bolt for stabiliser M 24 / SW 36 M 30 / SW 46 M 30 / SW 46 M 30 / SW 46 M 30 / SW 46 Tightening torque 1215 Screw connection threaded sleeve on air bag M 16 / SW 24 M = 130 Nm Screw connection bolt on air bag M 16 / SW 32 M = 130 Nm 1218 Lower central screw on the air bag piston M 16 / SW 19 M = 130 Nm 1219 Locking screw on Airlight Direct air bag M 12 / SW 8 M = 80 Nm 1222 Lower central screw on the air bag piston M 16 / SW 22 M = 230 Nm 1224 Bottom securing bolt of air bags Central bolt 1225 Mounting bracket screw, side and centre-mounted lift axle system M 16 / SW 22 M 16 / SW 22 M = 550 Nm (510-605 Nm) M = 650 Nm (605-715 Nm) M = 650 Nm (605-715 Nm) M = 900 Nm (840-990 Nm) M = 750 Nm (700-825 Nm) M = 900 Nm (840-990 Nm) M = 750 Nm (700-825 Nm) M = 230 Nm - 300 Nm M = 300 Nm M = 230 Nm 1240 Top locking screws of air bags M 12 / SW 17 M = 66 Nm 1324 Locking nut and hexagon screw for shock absorber 1330 Steel hanger bracket Aluminium hanger brackets M 24 / SW 36 M 24 / SW 36 M = 420 Nm (390-460 Nm) M = 320 Nm (300-350 Nm) 1571 Bolted connection, gusset plate on spring bolts M 18 x 1.5 / SW 27 M = 420 Nm (390-460 Nm) 1623 Bump stop fixing bolts, two-side axle lift M 6 / SW 10 M = 8 Nm 1631 Locking screw of the side plate for two-side axle lift M 8 / SW 13 M = 30 Nm 1635 Square bar fixing bolts for two-side axle lift M 12 / SW 17 M = 130 Nm 1636 Bolted connection for shaped plate on two-side axle lift bracket M 12 / SW 17 M = 75 Nm Bump stop fixing bolts for side and centre-mounted lift axle system M 12 / SW 17 M 10 / SW 17 M = 66 Nm M = 25 Nm 1637 Fixing bolts of bracket for anti-roll bar (U-shape) M 10 / SW 17 M = 53 Nm 1663 Securing nuts of diaphragm cylinder for axle lift M 20 x 2.5 / SW 30 M = 350-380 Nm M 16 x 1.5 / SW 24 M = 180-210 Nm

Page 16 BPW-WH-AL-SL-O 35391601e BPW-WH-AL-SL-O 35391601e Page 17 5 Safety regulations, safety information 5.1 Safety regulations All work must be performed by trained mechanics at competent repair facilities or authorised specialist companies who have access to all relevant tools and have acquired the knowledge required for this work. Anyone who performs maintenance and repair work must be trained in automotive mechanics and already have experience in repairing trailers and semi-trailers. Anyone who performs brake work must be trained in brake systems. Comply with local safety regulations. The relevant operation and service regulations as well as safety regulations of the vehicle manufacturer and of the manufacturers of other vehicle parts must be adhered to. The vehicle must be prevented from moving during repair work. Please observe the relevant safety regulations for repair work on commercial vehicles, in particular the safety regulations for jacking up and securing the vehicle. For all welding operations, the hangers, U-bolts, air bags and plastic lines must be protected against flying sparks and weld spatter. The earth terminal should under no circumstances be attached to the trailing arm, U-bolt or wheel hub. Do not carry out any welding on the trailing arm. Do not machine the trailing arms with cutters or grinders. The spring seat guides should always be widened if replacement trailing arms do not fit exactly into the bed of the axle spring seats. It is not permitted for the hanger brackets to be heated for straightening work! During repair work, make sure that the brake is not operated inadvertently. The brake must be released. Do not perform repair work unless wearing protective clothing (gloves, safety boots, safety goggles, etc.) and using the recommended tools. Only use recommended tools. A second technician must provide assistance when carrying out work with heavy components (trailing arms, stabilisers, brake discs, brake drums or during brake back disassembly or assembly). All air lines and components must be depressurised before being removed. Following each repair, perform a function check or a test drive in order to make sure that the brakes and suspensions are functioning correctly. New brake linings only have maximum effect after a few braking actions. Avoid hard braking. All exchanged components must be reused or disposed in accordance with the applicable environmental regulations, laws and directives. The remaining thickness of the brake lining and the condition of the brake disc or brake drum must be visually inspected at regular intervals with respect to the way in which the vehicle is used (see BPW maintenance instructions). Tighten all fixings to the recommended tightening torque. 5.2 Safety regulations This workshop manual contains different types of safety instructions, each of which is designated an icon and a key word. The key word describes the severity of the potential danger. i Warning! Caution! Repair Guide! Note! Possible potential danger of serious or fatal injury (severe injury or death). Possible dangerous situation (slight injury or damage to property). Risk of damage to property or consequential damage if this information is not observed. Application hints and especially useful information. It is essential that all maintenance work is carried out in accordance with the prescribed intervals in order to maintain the safe operation and roadworthiness of the trailer. The relevant operation and service regulations of the vehicle manufacturer and of the manufacturers of other vehicle parts must also be adhered to. Rectification of any defects which are discovered or replacement of worn parts should be carried out by a BPW Service Centre or BPW Direct Service Partner unless the vehicle owner has the facilities, equipment and workshop manuals and possesses an official certificate to perform interim inspections or special brake inspections. When installing spare parts, it is strongly recommended that only original BPW components are used. Parts approved by BPW for trailer axles and suspensions regularly undergo special test procedures. BPW accepts product responsibility for them. However, BPW cannot assess every single third-party product as to whether it can be used for BPW trailer axles and suspensions without any risk to safety. This applies even if such products have already been tested by an accredited test authority. The warranty becomes null and void if spare parts other than original BPW parts are used.

Page 18 BPW-WH-AL-SL-O 35391601e BPW-WH-AL-SL-O 35391601e Page 19 6 Care and Maintenance Overview For detailed description, see pages 22-30 Within 2 weeks of first journey under load, 1) latest after 2000 km Visual checks during the warranty period for chassis fitted with ECO Plus air suspension after 12, 36, 60 and 72 months Annually 2) 1 Grease U-stabiliser bearing bushes with BPW special longlife grease ECO-Li Plus and check for wear. - Visual inspection, check all component parts and welding seams for damage and wear. 1 1 3) - - 3) Series ALO/SLO Series ALO/SLO with two-sided axle lift 1 Check strap: Check condition and fastening. 1 1 2 Check air suspension levelling valve for condition, seal-tightness and general tightness. 2 2 3 Check condition of air bags. 3 3 4 Check shock absorber fastening for tightness. Tightening torque with a torque wrench: M 24 (SW 36) M = 420 Nm (390-460 Nm) For aluminium hanger brackets: M 24 (SW 36) M = 320 Nm (300-350 Nm) 4 4 4 5 Check spring pivot bolts for tightness. Tightening torque with a torque wrench: Hanger brackets and channel crossmember Airlight II from 09/2007: M 24 (SW 36) M = 650 Nm (605-715 Nm) Hanger brackets from 8/2001: M 30 (SW 46) M = 900 Nm (840-990 Nm) Hanger brackets up to 7/2001: M 30 (SW 46) M = 750 Nm (700-825 Nm) Channel crossmember: M 30 (SW 46) M = 900 Nm (840-990 Nm) 5 5 5 Series ALM/SLM with Combi Air bag II Series ALM/SLM with bolted-on air suspension hanger bracket 6 Check spring mounting kit for tightness. Tightening torque with a torque wrench: M 20 (SW 30) M = 340 Nm (315-375 Nm) M 22 (SW 32) M = 550 Nm (510-605 Nm) M 24 (SW 36) M = 650 Nm (605-715 Nm) When mounting new spring mounting kits for Airlight II: M 22 (SW 32) M = 550 Nm + 90 angle tightening 6 6 6 1) ECO Plus Units with Airlight II and Airlight Direct air suspension are maintenance-free in On-Road applications and do not need to be retightened (see warranty documents ECO Plus).) 2) Under extreme conditions, with more frequency 3) Check twice annually. Series ALU/SLU with sidewise mounted axle lift Series DLU - Airlight Direct

Page 20 BPW-WH-AL-SL-O 35391601e BPW-WH-AL-SL-O 35391601e Page 21 6 Care and Maintenance Overview For detailed description, see pages 22-30 7 Check the bolt connection between the air suspension hanger bracket and the longitudinal member for tightness. Tightening torques with a torque wrench: M 16 M = 260 Nm (240-285 Nm) Within 2 weeks of first journey under load, 1) latest after 2000 km Visual checks during the warranty period for chassis fitted with ECO Plus air suspension after 12, 36, 60 and 72 months. Annually 2) 7 7 7 Series ALO/SLO Series ALO/SLO with two-sided axle lift 8 9 Tighten the spring bolt to gusset plate connecting bolt. Tightening torques with a torque wrench: M 18 x 1.5 (SW 27) M = 420 Nm (390-460 Nm) Check axle lift for tightness. Tightening torques with a torque wrench: Cylinder M 20 (SW 30) M = 350-380 Nm M 16 (SW 24) M = 180-210 Nm Supporting arm M 16 (SW 22) M = 230 Nm Hexagon screw M 12 (SW 17) M = 75 Nm 8 8 8 9 9 9 10 11 Check air bag fastening for tightness. Tightening torques with a torque wrench: M 12 (SW 17) M = 66 Nm M 16 (SW 22) M = 230-300 Nm Lower attachment - centre screw M 16 (SW 22) M = 300 Nm Check U-stabiliser fastenings. Tightening torques with a torque wrench: M 10 (SW 17) M = 53 Nm M 30 (SW 46) M = 750 Nm (700-825 Nm) 10 10 10 11 11 11 Series ALM/SLM with Combi Air bag II Series ALM/SLM with bolted-on air suspension hanger bracket and bolt-on double-sided lift 1) ECO Plus Units with Airlight II and Airlight Direct air suspension are maintenance-free in On-Road applications and do not need to be retightened (see warranty documents ECO Plus). 2) Under extreme conditions, with more frequency. Note: Components that have damage due to improper mounting are to be exchanged after a review by a BPW Service Centre. Series ALU/SLU with sidewise mounted axle lift Series DLU - Airlight Direct

Page 22 BPW-WH-AL-SL-O 35391601e BPW-WH-AL-SL-O 35391601e Page 23 6 Care and Maintenance 1 U-stabiliser bearing bushes Service intervals as shown on page 18 2 Air installation circuit Service intervals as shown on page 18 Grease U-stabiliser bearing bushes with BPW special longlife grease ECO-Li Plus and check for wear. Check air installation valves and line connections for firm seating, damage and seal tightness. Check valve linkage and fastenings (arrows) for damage and tightness. The length of the valve lever and permissible angular positions for the valve linkage are shown in the illustration below. - Visual inspection Service intervals as shown on page 18 Air suspension valve Check all component parts and welding seams for wear and damage. 1 Check straps Service intervals as shown on page 18 Examine check straps and attachment. Replace if necessary. Check axle beam for wear.

Page 24 BPW-WH-AL-SL-O 35391601e BPW-WH-AL-SL-O 35391601e Page 25 6 Care and Maintenance 3 Air bags Service intervals as shown on page 18 5 Spring pivot bolts Service intervals as shown on page 18 Check air bags for external damage (surface cracking, abrasion, crease formation, trapped foreign bodies etc.). Replace air bags in the event of damage. Check bushes, move vehicle back and forth slightly with the brake applied, or move rolled spring ends with the aid of a lever. No play should be present in the rolled spring end when doing so. If the fastening is loose the spring pivot bolt may be damaged. Danger! RISK OF INJURY! No welding should be carried out on steel parts of air bags and pressure vessel! - Check the lateral wear washers in the hanger bracket. - Check the M 24 or M 30 lock nut on the spring pivot bolt for tightness. The air suspension should only be filled with compressed air when mounted. Tightening torque with a torque wrench: Air suspension hanger brackets and channel crossmember from 09/2007: M 24 (SW 36) M = 650 Nm (605-715 Nm) Hanger brackets from 08/2001: M 30 (SW 46) M = 900 Nm (840-990 Nm) Hanger brackets up to 07/2001: M 30 (SW 46) M = 750 Nm (700-825 Nm) Channel crossmember: M 30 (SW 46) M = 900 Nm (840-990 Nm) The serviceable life of the rubber / steel bush is dependent on the tightness of the inner steel bushing. Non-adjustable hanger bracket 4 Shock absorber fastening Service intervals as shown on page 18 Check lower and upper shock absorber fastening for tightness. Tightening torques with a torque wrench. Check condition and wear of the rubber bushing and replace where appropriate. Check shock absorbers for oil leakage. In cases of distinct traces of oil, the shock absorber must be replaced. A light mist of oil is acceptable! Tightening torque: M 24 (SW 36) M = 420 Nm (390-460 Nm) In the case of alloy hanger brackets: M 24 (SW 36) M = 320 Nm (300-350 Nm) Adjustable hanger bracket

Page 26 BPW-WH-AL-SL-O 35391601e BPW-WH-AL-SL-O 35391601e Page 27 6 Care and Maintenance 6 Spring mounting kit Service intervals as shown on page 18 8 Bolted connection, gusset plate spring bolts Service intervals as shown on page 20 Check lock nuts of spring U-bolts for tightness. If loose, tighten nuts alternately a little at a time. Tightening torques with a torque wrench: M 20 (SW 30) M = 340 Nm (315-375 Nm) M 22 (SW 32) M = 550 Nm (510-605 Nm) M 24 (SW 36) M = 650 Nm (605-715 Nm) When mounting new spring mounting kit components for Airlight II, tighten the M 22 locknuts to a tightening torque of: M = 550 Nm + 90 angle tightening. No welding should be performed on the trailing arm spring! Check the mounting bolts of the gusset plates on the spring bolts are firmly tightened, and retighten with a torque wrench if necessary. Tightening torque: M 18 x 1.5 (SW 27) M = 420 Nm (390-460 Nm) Installing or renewing the spring bolt: 1. Unscrew or install the spring bolt. 2. Loosely pre-mount the gusset plate with at least three M 16 bolts at the top on the crossmember and one M 18 bolt at the bottom on the spring bolt and tighten further until contact is made. 3. Set the track. 4. Tighten the spring bolt to the prescribed tightening torque. 5. Tighten the connecting bolt on the gusset plates spring bolt and then tighten the upper connecting bolt to the prescribed tightening torques. 7 Bolted connection, air suspension hanger bracket to longitudinal chassis beam Service intervals as shown on page 20 Check that the mounting bolts of the air suspension hanger bracket on the longitudinal member are firmly tightened. Tighten with a torque wrench if necessary. Tightening torque: M 16 M = 260 Nm (240-285 Nm)

Page 28 BPW-WH-AL-SL-O 35391601e BPW-WH-AL-SL-O 35391601e Page 29 6 Care and Maintenance 9 Axle lift Service intervals as shown on page 20 Single-sided lift Spring pivot bolt bearing with axle lift Single-sided lift Two-sided lift Check the M 16 lock nuts on the lever arm fixing to make sure they are tight. Tighten with a torque wrench if necessary. Tightening torque: M 16 (SW 22) M = 230 Nm Check for wear on the bump stop on the lever arm. Make sure it is secure. Tightening torque: M 10 (SW 17) M = 25 Nm M 12 (SW 17) M = 66 Nm Single-sided lift Two-sided lift: a) Check the M 16 lock nuts on the diaphragm cylinder to make sure they are tight. Tighten with a torque wrench if necessary. Tightening torque: M 20 (SW 30) M = 350-380 Nm M 16 (SW 24) M = 180-210 Nm b) Check the bump stop on the lever arm for wear, and that the M 6 attachment bolts are firmly tightened. Bolt-on two - sided lift Two-sided lift c) Check that the attachment bolts of the front bracing strut of the mount on the air suspension hanger bracket are tight, and in the case of the bolt-on two-sided lift, the bolted connection on the air suspension hanger bracket. Tightening torque: M 12 (SW 17) M = 75 Nm Bolt-on double-sided lift

Page 30 BPW-WH-AL-SL-O 35391601e BPW-WH-AL-SL-O 35391601e Page 31 6 Care and Maintenance 10 Air bag fastenings Service intervals as shown on page 20 Check air bag fixing bolts or nuts for tightness. If necessary retighten using torque wrench. Tightening torques: M 12 (SW 17) M 16 (SW 22) M = 66 Nm M = 230-300 Nm Lower attachment - centre screw: M 16 (SW 22) M = 300 Nm 11 U-stabiliser Service intervals as shown on page 20 Check U-stabiliser bearings for wear and tightness. Tightening torques with a torque wrench: M 10 (SW 17) M = 53 Nm M 30 (SW 46) M = 750 Nm (700-825 Nm)

Page 32 BPW-WH-AL-SL-O 35391601e BPW-WH-AL-SL-O 35391601e Page 33 7 Dismantling and assembly of axle and trailing arms Dismantling Note the ride height (FH) of the air suspenion at its normal setting. To do this, measure the distance from the axle to the lower edge of the frame and record it. [6] Vent the brake system. If spring-type brake actuator fitted, eliminate preload. [7] Remove the parking brake cables, if necessary. [8] Disconnect the compressed air hoses from the brake cylinders. [9] Detach tension spring at the shut-off valve, if necessary. [10] Undo all cable connections to the axle (Brake Monitor, ABS sensor cable, etc.). Picture 1 Picture 4 [1] Secure vehicle to prevent rolling away. [2] Raise vehicle, inflate air bags to maximum height by setting lever for rotary disc valve / changeover valve on air suspension to Lift and then to Stop. On air suspension systems without rotary disc valve / change-over valve, unscrew nut (picture 3/2) on linkage (picture 3/1) for air spring valve on axle and actuate the lever on the air suspension levelling valve until air bags have reached maximum height. [11] Remove the catch straps (1360), if necessary, see chapter 12. If check strap attached with split pin bolt, the check strap only needs to be taken off at one side. Picture 2 Picture 5 [3] Support frame in this position to prevent accidents. [4] Release air from air bags by setting rotary disc valve / change-over valve on air suspension to Lower. 1 [12] If the shock absorbers mountings have threaded pins, the shock absorbers (1300) must be removed by unscrewing the upper and lower lock nuts (1330, SW 36). On air suspension systems without rotary disc valve / change-over valve, actuate valve lever on air suspension levelling valve until air has escaped from air bags. Warning! RISK OF INJURY when working on air bags under pressure! [5] Lift axle slightly with vehicle jack and remove wheel, if required. Picture 3 2 Picture 6

Page 34 BPW-WH-AL-SL-O 35391601e BPW-WH-AL-SL-O 35391601e Page 35 7 Dismantling and assembly of axle and trailing arms If shock absorber attached between plates, remove bottom nut (1330) of the securing bolt (1324). Remove the bolt and spacer sleeves or washers (1318), if present. [16] Unscrew locking nuts (1168, SW 36 / SW 46) of the spring pivot bolts (1154). [17] Remove the washers (1165) from adjustable air spring bracket with adjusting plate (1161). Picture 7 Picture 10 [13] Support axle with movable vehicle lifter (low-lift platform truck) to prevent accidents. [14] Remove bottom locking bolt(s) (1224, SW 22), depending on design of air bag (1200). Not required for Airlight Direct air suspension or combination air bag. [18] Drive spring pivot bolts (1154) out of the hanger brackets and of the trailing arm bushes (1000). In the case of the version with an adjustable hanger bracket take off the connecting link discs (1161). [19] Carefully let down and pull out the axle. For axle lift device, see chapter 13. Picture 8 Picture 11 [15] For air suspension with anti-roll bar (U-shape) (1815), remove the lock nuts (1168) from the mounting screws (1156) to the spring plates (1032, 1033) and pull out the mounting screws. [20] Examine wear plates (1525) in the steel hanger bracket (1510) for wear, and remove, if necessary. If wear plates are tack-welded, separate the components and tack-weld new ones. In case of loose mounted wearing plates, e.g. Airlight II, mount new tracking plates (1525). Picture 9 Heating up of the hanger brackets for alignment work is not allowed. Picture 12 loose wear plates track-welded wear plates

Page 36 BPW-WH-AL-SL-O 35391601e BPW-WH-AL-SL-O 35391601e Page 37 7 Dismantling and assembly of axle and trailing arms Replacement of worn weld-in bushes [21] Separate the worn bushes (1535, 1540) from the side plates of the support (1510, 1511). [22] Insert new bushes and harness with a distance sleeve or trailing arm bush (1005) and wear plates (1525) Align and tack weld centrally as well as horizontally. For adjustable supports; see Picture 13 (TA=trailing arm). [23] Disassemble bolting and fully weld the bushes. Seam thickness a 4 to a 5 (DIN EN ISO 25817) Welding technique: Gas-shielded welding, weld quality G 4 Si 1 (DIN EN 440) or E 46 2 (DIN EN 499) for arc welding rod electrodes. Picture 13 [27] For loose wearing plates (1525), mount these from underneath between trailing arm (1000) and air spring bracket (1510, 1511). [28] Fully insert spring bolt (1154) until the square profile under the head of the spring bolt engages in the torsion protection (arrow) recess of the weld in bushes. See chapter 13 for the version with axle lift. Picture 16 [24] If alloy hanger brackets fitted, examine inner plates (1530) and outer plates (1531), drive out, if necessary and press in new plates. [29] Push the plate (1165) onto the spring pivot bolt (1154), screw on new locking nuts (1168, SW 46) and tighten to the specified torque of: For the fitting and demounting of trailing arm springs, see chapter 8. Hanger brackets from 08/2001: M 30 (SW 46) M = 900 Nm (840-990 Nm) Hanger brackets up to 07/2001: M 30 (SW 46) M = 750 Nm (700-825 Nm) Channel crossmember M 30 (SW 46) M = 900 Nm (840-990 Nm) See page 39 for the further installation procedure, starting from step [31]. Picture 14 Picture 17 Assembly Assembly Version A: rigid hanger bracket Version B: Adjustable hanger bracket [25] Place axle on movable vehicle lifter (low-lift platform truck) to prevent accidents, push below the frame and raise far enough until the holes of the trailing arm and hanger bracket are aligned. [25] In the version up to 2001, apply grease to the sliding surfaces of the sliders (1160) and insert into the hanger bracket (1511) on the left and right until flush. [26] Smear spring pivot bolt (1154) with grease and insert into the holes from the outside. We recommend mounting the spring bolt from the outside to the inside in order to make it easier to tighten the lock nuts over an inspection pit. Picture 15 [26] Place axle on movable vehicle lifter (low-lift platform truck) to prevent accidents, push below the frame and raise far enough until the holes of the trailing arm and hanger bracket are aligned. (The slide elements must remain in position.) Picture 18

Page 38 BPW-WH-AL-SL-O 35391601e BPW-WH-AL-SL-O 35391601e Page 39 7 Dismantling and assembly of axle and trailing arms [27] In the version from 2001 onwards with loose shaped plates, e.g. Airlight II: mount the shaped plates (1525) from below between the hanger bracket (1511) and the trailing arm (1000) (make sure the holes in the trailing arm, hanger bracket and shaped plate line up). [31] Lift the axle to the ride height as measured before step [1]. Picture 19 Picture 22 [28] Push connecting link disc (1161) onto the square spring bolt, ensuring correct positioning of the connecting link disc. [29] Smear spring pivot bolt (1154) with grease and with the connecting link disc pushed on, fit into the spring eye from the outside. In doing so the connecting link disc must engage into the mouth of the hanger bracket. See chapter 13 for the version with axle lift. [32] Align adjusting plates (1161) on both sides and centrally and evenly tighten lock nuts (1168, SW 36 / SW 46) do not fully tighten until secure. (The spring bolt screw connection is tightened after the track of the axle has been adjusted.) Picture 20 Picture 23 [30] Fit connecting link disc (1161), washer (1165) and new lock nut (1168). The bevels of the connecting link discs must be flushed with one another and engaged in the mouth of the hanger bracket on both sides. [33] Clean the contact area of the air bag (1200) and the trailing arm (1000). [34] Position the air bag on the trailing arm. Do not tighten the lock nut! Air bag with central bolt connection [35] Screw in locking screw M16 (1224, SW 22) and tighten to the specified torque of M = 300 Nm. Picture 21 Picture 24

Page 40 BPW-WH-AL-SL-O 35391601e BPW-WH-AL-SL-O 35391601e Page 41 7 Dismantling and assembly of axle and trailing arms Air bag with universal and steel plate [35] Screw in locking screw M16 (1224, SW 22) and tighten to the specified torque of M = 230-300 Nm. [37] Install check straps (1360), see chapter 12. [38] If present, insert the extension spring of the shut-off valve into the bracket on the axle beam and attach to the shut-off valve. If the hexagon screw (1222, SW 22) was loosened during disassembly, check the specified torque of M = 230-300 Nm. Picture 25 Picture 28 When using PDC shock absorbers, a distance washer (1055) as well as shorter lock nuts (1330) must be used in each case between support or spring pad and PDC. [39] Re-connect the compressed air hose onto the brake cylinder. [40] Re-attach all cable connections to the axle (Brake Monitor, ABS sensor cable, etc.). [41] Fit the parking brake cables, if present. [36] If shock absorber (1300) attached to threaded bolt, mount the shock absorber with the protective sleeve facing up. Screw on new lock nuts (1330, SW 36) and tighten to the prescribed torque. Tightening torque: M 24 M = 420 Nm (390-460 Nm) In the case of alloy hanger bracket M = 320 Nm (300-350 Nm) In the case of a shock absorber fastening between plates, depending on the version, insert washers or spacer sleeves (1318) between shock absorber eye and plate. Push in the fastening screw (1324), screw on the new lock nuts (1330, SW 36) and tighten to the prescribed torque, see step [36]. Picture 26 [42] Place the suspension linkage (Picture 30/1) of the air suspension valve in the bracket on the axle beam and secure with nut (Picture 30/2) and spring washer. [43] Replace wheels. [44] Inflate air bags and remove supports. Check the air suspension valve setting, correct it to the originally measured ride height, if necessary, see chapter 14. Perform axle alignment check, see chapter 16. [45] After adjusting the axle track, tighten the spring bolt nut (1168, SW 36 / SW 46) to the prescribed tightening torque. Air suspension hanger brackets and channel crossmember Airlight II from 09/2007: M 24 (SW 36) M = 650 Nm (605-715 Nm) Hanger brackets from 08/2001: M 30 (SW 46) M = 900 Nm (840-990 Nm) Hanger brackets up to 07/2001: M 30 (SW 46) M = 750 Nm (700-825 Nm) Channel crossmember: M 30 (SW 46) M = 900 Nm (840-990 Nm) Picture 29 2 1 Picture 27 Picture 30

Page 42 BPW-WH-AL-SL-O 35391601e BPW-WH-AL-SL-O 35391601e Page 43 8 Dismantling and assembly of trailing arm 8.1 Dismantling [1] Deflate air bags (1200), see page 32, steps [1] - [4]. [2] Support axle on the side on which the trailing arm is to be removed with movable vehicle lifter (low-lift platform truck) to prevent accidents. [8] Push out the spring bolt (1154) from the air suspension and the trailing arm (1000). For versions with an adjustable support, detach the adjusting plate (1161). If side axle lift device fitted, see chapter 13. [3] If air suspension system is fitted with a U-stabiliser, the securing bolts at the spring plates must be removed, see chapter 9, page 57. [4] When the shock absorber is secured to the lower spring plate (1032, 1033) with a welded bolt, remove the mounting nut (1330) and shock absorber completely. In cases where the shock absorber is mounted to the upper spring plate, disconnect by removing the lower bolt and nut (1324, 1330). Picture 1 Caution! RISK OF INJURY! Secure the trailing arm against falling out. Use a hoist or ask a second person for assistance. Picture 4 [5] Depending on the air bag version (1200), disassemble the lower locking screw(s) (1224, SW 22). By loosening the U-bolts of the positive axle clamping, all components are slackened and can be easily detached and exchanged. [9] Screw the lock nuts (1057, SW 32) (1330, SW 36) from the U-bolts (1050) and, if necessary, take off the washers (1055). [10] Remove spring plate (1032, 1033), spring U-bolts and any segments (1035). Picture 2 Picture 5 [6] Remove lock nut (1168, SW 36 / SW 46) from the spring bolt (1154). [7] For air suspension with adjusting plate (1161), remove the nut (1168) and washers (1165). [11] For single-leaf springs with catch plate (1012), detach the trailing arm (1000) from the axle. [12] In the case of axles with a positive axle clamping remove the centring bolt (1040) between trailing arm spring and catch plate hole, the tracking plate (1041, if present) and the spring seats (1026, 1027). [13] Check steel/rubber/steel bush (1005) in the trailing arm spring for wear, replacing if necessary. See chapter 8.4. [14] Check the centering frame (25) on the axle beam for wear and, if necessary, replace and re-weld. Picture 3 [15] For axles with welded axle mounting, take out the tracking plate (1041), if present, from the axle spring seats. Any welded-on tracking plates must be ground off and welded back on again after a tracking check. Picture 6

Page 44 BPW-WH-AL-SL-O 35391601e BPW-WH-AL-SL-O 35391601e Page 45 8 Dismantling and assembly of trailing arm 8.2 Assembly [16] Free the contact areas on the axle beam and axle mounting from dirt and welding spatter, and check condition. [17] For top-mounted air suspension, position the trailing arm (1000) on the axle beam or axle spring seats. For single-leaf springs, this should also include the catch plate (1012) and plug (1015). For bottom-mounted air suspension, position the trailing arm (1000) under the axle beam. For singleleaf springs, this should also include the catch plate (1012) and plug (1015). For single-leaf spring, position the catch plate so that there is a clearance of 8 mm after installation (see detailed view, Picture 7). Non adjustable hanger bracket: [18a] Insert the trailing arm (1000) with the steel-rubbersteel bush in the support (1510) until the bore holes of the trailing arm and support are aligned. [19a] Smear spring pivot bolt (1154) with grease and insert into the hole from the outside. We recommend mounting the spring bolt from the outside to the inside in order to make it easier to tighten the lock nuts (1168) over the pit. Picture 7 Picture 8 Adjustable support with sliders: [18b] For versions until 2001, grease the sliding surfaces of the sliders (1160) and place in the support (1511), aligning it to the right and left (1511). [19b] Insert the trailing arm (1000) with the steel-rubbersteel bush between the slides (1160) in the support (1511) until the bore holes are aligned. [20b] Push connecting link disc (1161) onto the square spring pivot bolt. [21b] Smear spring pivot bolt (1154) with grease and insert into the hole from the outside. Go to Section 8.2.1 on page 46 for top-mounted air suspension or Section 8.2.2 on page 49 for bottom-mounted air suspension. If side axle lift device fitted, see chapter 13. Picture 10 Picture 11 [20a] For loose wearing plates (1525), mount these between trailing arm (1000) and air spring (1510). [21a] Fully insert spring bolt (1154) until the square of the spring bolt is in the torsion protection (arrow) of the weld-in bushes. Go to Section 8.2.1 on page 46 for top-mounted air suspension or Section 8.2.2 on page 49 for bottom-mounted air suspension. If side axle lift device fitted, see chapter 13. Adjustable support with round weld-in bushes: [18c] Insert the trailing arm (1000) with the steel-rubbersteel bush in the support (1511) until the bore holes of the trailing arm and support are aligned. [19c] Mount the wearing plates (1525) from below, between support (1511) and trailing arm (1000) (pay close attention to the alignment of the bore holes of trailing arm, support and shaped plate). Picture 9 Picture 12

Page 46 BPW-WH-AL-SL-O 35391601e BPW-WH-AL-SL-O 35391601e Page 47 8 Dismantling and assembly of trailing arm [20c] Slide the adjusting plate (1161) onto the square of the spring bolt. Pay close attention to correct positioning of the adjusting plate. [21c] Grease the spring bolts (1154) and mount in the spring eye with a suspended adjusting plate from the outside. The adjusting plate should mesh with the support jaw. Clamping of trailing arm with centering bolt on tracking plate [23] Place the tracking plate with mounted centering bolt (1041) into the bore hole of the trailing arm (1000) / catch plate (1012) or into the axle spring seats 1026,1027). If side axle lift device fitted, see chapter 13. See page 48 for further installation with step [24]. For versions with bottom-mounted trailing arm, continue in Section 8.2.2, page 49. Picture 13 Picture 16 8.2.1 Top-mounted air suspension (trailing arm over the axle) SLO/SLM - ALO/ALM To fit the spring mounting kit components, lift the trailing arm slightly. [22] Align spring seats (1026, 1027) with the axle beam centring ring (25). (Not used in welded axle connections.) Two-part trailing arm with spring screw [23] Insert the tracking plate (1041) centred into the axle spring seats (1026, 1027) or attach it to the head of the centre bolt (1018) in the trailing arm (1000). See page 48 for further installation with step [24]. Picture 14 Picture 17 Clamping of trailing arm without tracking plate (only with single-leaf spring for centering bolt) [23] Place the centering bolt (1040) in the axle spring seats (1026, 1027) or the bore hole of the trailing arm (1000) / catch plate (1012). Note: In newer versions, the centering bolt is already forged onto the axle spring seats. Twin leaf trailing arm with centre bolt Centering ring / centering plate for adjustable support [23] Place the centering plate or centering ring (1042) in the axle spring seats (1026, 1027) on the weldedcentring frame (25) on the axle body and centre the axle spring seats. The tracking plate (1041) is not needed. See page 48 for further installation with step [24]. Picture 15 Picture 18

Page 48 BPW-WH-AL-SL-O 35391601e BPW-WH-AL-SL-O 35391601e Page 49 8 Dismantling and assembly of trailing arm [24] Lay the trailing arm spring (1000) complete with centring bolt or tracking plate (1041) in the spring seat (1026, 1027). [25] Fit new spring U-bolts and segments (1035). For attachment of the trailing arm with hexagon screws (1053), these are mounted according to step [27]. Picture 19 8.2.2 Under-slung air suspension (trailing arm under the axle) SLU - ALU - DLU Clamping of trailing arm without tracking plate or with centering bolt or tracking plate under the trailing arm [22] Place the axle spring seats (1026, 1027) in the correct position on the trailing arm (1000) or, where applicable, the catch plate (1012). (Not applicable for welded axle mountings.) See page 50 for further installation with step [24]. Picture 22 [26] Depending on the spring plate version (1032, 1033), mount the axle spring seats (1024) or double latch (1024) onto the U-bolt ends. Spring plate Spring pad Double segment Twin leaf trailing arm with centre bolt and tracking plate [22] For a two-part trailing arm (1000), place the tracking plate (1041) onto the head of the spring screw (1018). [23] Place the axle spring seats (1026, 1027) onto the tracking plate. See page 50 for further installation with step [24]. Picture 20 Picture 23 [27] Attach new discs (1055). [28] Lightly grease the threads of the new U-bolts (1050) / hexagon screws (1053) and the nut contact area. [29] Unscrew the new lock nuts (1057, SW 32) (1330, SW 36) by hand on the U-bolt / hexagon bolts. A rounded washer must be fitted for spring plates with spherical countersink. with spherical countersink without spherical countersink Twin leaf trailing arm with centre bolt and centering ring with adjustable support. [22] Place the centering ring (1042) onto the head of the spring screw (1018). The tracking plate (1041) is not needed. [23] Place the axle spring seats (1026, 1027) onto the trailing arm (1000) (centering ring). See page 50 for further installation with step [24]. [30] Align the axle under the vehicle. Further installation, see Section 8.3 page 53. Picture 21 Picture 24

Page 50 BPW-WH-AL-SL-O 35391601e BPW-WH-AL-SL-O 35391601e Page 51 8 Dismantling and assembly of trailing arm DLU version [22] Insert the centering bolt (1040) in the hole of the trailing arm (1000) / catch plate (1012). [27a] For the clamping of a trailing arm with centering bolt on the tracking plate (1041), insert the centering bolt into the bore hole for the trailing arm / catch plate. [23] Position the axle spring seats (1026, 1027) on the trailing arm (centering plate) in such a way that the centering bolt is situated in the designated bore hole in the axle spring seat. Picture 25 [27b] For the clamping of a trailing arm with centering bolt (1040), insert the centering bolt into the bore hole in the spring plate (1032, 1033). [27c] For the clamping of a trailing arm with two tracking plates with centering bolts (1041), insert a bolt into each bore hole of the trailing arm / catch plate and one into the bore hole in the spring plate. Picture 28 [24] From below, push the trailing arm (1000) with axle spring seats (1026, 1027), and where applicable the tracking plate (1041) or centering ring (1042), against the axle beam. For mounting U-bolt from bottom to top, continue with step [25] page 52. [28] Slide the spring plate (1032, 1033) onto the U-bolt (1050) from below. Attach new washers (1055). [29] Lightly grease the threads of the new U-bolts (1050) / hexagon screws (1053) and the nut contact area. [30] Screw the new lock nuts (1057, SW 32) (1330, SW 36) by hand on the U-bolt / hexagon bolts (1053). Further installation, see Section 8.3 page 53. Picture 26 Picture 29 U-bolt mounting from top to bottom [25] Place the segment plate (1035) or axle spring seats (1024) on the centring frame (25) of the axle beam. (Not applicable for welded axle mounting.) [26] Insert U-bolt / hexagon bolts from above until they are resting on the segment plate or axle spring seats. Depending on the version, the U-bolts are mounted in front of / behind or alongside the axle beam. U-bolt mounting from top to bottom DLU version: [25] With offset in the direction of the axle centre, place the conical axle spring seats (1035) on the centring frame (25) of the axle beam. [26] Position the U-bolt through the lower axle spring seats (1026, 1027) until the U-bolt is resting on the upper axle spring seats (1035). Picture 27 Picture 30