BREAKERS, TAMPERS & DRIVERS Flush face couplers are factory installed. REL-GRD SERIES THE DOOGIE DRIVER GROUND ROD DRIVER The REL-GRD Series Ground Rod Driver from RELIABLE EQUIPMENT has been designed to drive galvanized ground rods FAST. Cushioned Comfort Grip handles run the length of the tool body providing two handed control while reducing operator fatigue. 70 inch whips with remote in-line ON/OFF valve provides convenient access to control for accurate drive depth. Operate from any Open- or Closed- Center hydraulic systems. The integral lifting eye allows the driver to be lifted and suspended above the rod reducing operator strain. MODEL REL-GRD-1 REL-GRD-3/4 REL-GRD-A-1 Pressure 2000 psi Max. 2000 psi Max. 2000 psi Max. Flow 5-8 gpm (18-30 lpm) 5-8 gpm (18-30 lpm) 5-8 gpm (18-30 lpm) Whip Set 70 in. (178 cm) 70 in. (178 cm) 70 in. (178 cm) Ports 9/16-18 SAE O-Ring 9/16-18 SAE O-Ring 9/16-18 SAE O-Ring Rod Diameter 1/2-5/8 in. 3/4 in. 1 in. Length 25-1/2 in. (654 mm) 25-1/2 in. (654 mm) 25-1/2 in. (654 mm) Weight 44 lbs. (24. 0 kg) 44 lbs. (24. 0 kg) 44 lbs. (24. 0 kg) HYD. GROUND ROD DRIVERS GROUND ROD DRIVERS The easy to use Tiiger Ground Rod Driver eliminates the need to climb above the rod for installation. It s designed with a unique positioning guide pin, which allows the driver socket of the impact tool to be engaged to the Ground Rod Driver. You can position it at any height for installation. FEATURES Position at any height for easy and safe installation Positioning guide allows driver socket of rotary hammer to be engaged to ground rod driver Manufactured from high quality steel, designed with a backside support ridge Heat treated for long life Eliminates need to climb above rod The use of impact tools or jack hammers may shorten service life Made in USA GRD0010 1/2" GRD0015 5/8" GRD0020 3/4" Refer to breakers and hammers on the following four pages. 106 QUALITY I EXPERIENCE I PROFESSIONALISM I DEDICATION
QUALITY I EXPERIENCE I PROFESSIONALISM I DEDICATION REL-MGRD SERIES TEMPORARY GROUNDING SYSTEM Temporary Screw Grounds provide an effective alternative to auger type grounding devices in situations where the work area is hard or frozen. A 5 foot section of 5/8 inch copper clad threaded ground rod is Included. REL-MGRD-TH - Ground Rod Driver with Handles Size: 29-1/2" L x 7" W x 2-3/4" R Weight: 28.5 lbs. REL-MGRD - Ground Rod Driver without Handles Size: 29-1/2" L x 2-3/4" R Weight: 23.5 lbs. OPTIONAL: REL-GR-ADP - Ground Rod Adapter For permanent installation of standard 5/8 ground rod. TEMPORARY INSTALLATION 1. Install & tighten thumb screw securing driver shaft. 2. Screw 5/8" threaded ground rod into threaded end of driver shaft. 3. Loosen thumb screw. 4. Grasp driver with both hands and impact rod down to desired depth. 5. Connect grounding cable from any equipment that is to be grounded to the temporary rod below driver body using a suitable connector clamp. REMOVAL OF TEMPORARY GROUND ROD 1. Remove cable from temporary ground assembly. 2. Impact driver upward to remove rod from ground. REL-GR-ADP Adapter for use with 3. Tighten thumb screw. Stand. Ground Rod. 4. Unscrew rod from driver and store. REL-MGRD-TH REL-MGRD REL-MGRD-ROD Reusable Threaded Temp. 5/8" x 5' Ground Rod BREAKERS, TAMPERS & DRIVERS MANUAL GROUND ROD DRIVER The REL-MGRDH provides a safe effective method of installing a standard 5/8 ground rod without the use of a sledge hammer, or powered ground rod drivers. REL-MGRDH - Ground Rod Driver with Handles Drive Shaft: 29-1/2" L x 7" W x 2-3/4" R Weight: 28.5 lbs. REL-MGRD-NH - Ground Rod Driver NO Handles Drive Shaft: 29-1/2" L x 2-3/4" R Weight: 23.5 lbs. INSTALLATION 1. Install & tighten thumb screw securing sliding impact shaft. 2. Slide driver over ground rod. (Note: Thumb Screw at Top) 3. Grasp driver with both hands and impact rod down to desired depth. 4. Tighten thumb screw securing the sliding impact shaft and remove driver from rod. 5. Install grounding assembly as required by application. DRIVE ROD BELOW GRADE 1. Slide driver over ground rod. (Note: Thumb Screw at Bottom) 2. Grasp driver with both hands and impact rod down to desired depth. REL-MGRDH Manual Ground Rod Driver with Handles REL-MGRD-NH Manual Ground Rod Driver w/o Handles MANUAL GROUND ROD DRIVERS 107
BREAKERS, TAMPERS & DRIVERS PNEUMATIC Model 131 Model 650 Model 119 119 - TRENCH DIGGER Built-in automatic oiler T-style forged handle (New) Rubber handle grips Teflon-faced throttle valve Automatic valve Deep case-hardened drop forged alloy steel cylinders Replaceable chuck bushing Latch-type retainer 131 - BACKFILL TAMPER Built-in large automatic oiler Flapper valve design allows dirt to pass without stopping the tool Internally reinforced large malleable iron butt. (Standard) Pole (half-moon), and 3" dia. butts available. 650 - CHIPPING HAMMERS 4-bolt style handle for ease of maintenance Available in 2, 3, and 4 strokes Drop-forged, vibration dampening handle Flapper valve allows dirt to pass without stopping the tool Deep case-hardened alloy steel cylinders Replaceable bushing Adjustable exhaust deflector Choice of optional retainers including the APT latch-type TRENCH DIGGER MODEL CHUCK SIZE BORE STROKE B.P.M. CFM @ 90 PSI WEIGHT LENGTH AIR INLET NPT 119 7/8 x 3-1/4-1 x 4/1/4 1-3/4 3-3/8 1500 34-38 37 lbs. 31 in. 1/2" fem. BACKFILL TAMPER MODEL BORE STROKE B.P.M. CFM @ 90 PSI WEIGHT LENGTH AIR INLET NPT 131 1-1/2 5-1/2 670 38-42 37 lbs. 51-7/8" 1/2" fem. CHIPPING HAMMERS MODEL BORE STROKE B.P.M. CFM @ 90 PSI WEIGHT W/O RETAINER LENGTH W/O RETAINER CHUCK BUSHING AIR INLET 652 1-1/8 2 2100 32-34 12 lbs. 13-1/4 in..680 R or.580 H. 7/8-24 653 1-1/8 3 1650 33-35 14 lbs. 15-1/4 in..680 R or.580 H 7/8-24 654 1-1/8 4 1375 34-36 16 lbs. 16 in..680 R or.580 H 7/8-24 108 QUALITY I EXPERIENCE I PROFESSIONALISM I DEDICATION
QUALITY I EXPERIENCE I PROFESSIONALISM I DEDICATION REL-TMP SERIES HYDRAULIC POLE TAMPERS The REL-TMP Series Hydraulic Pole Tampers from Reliable is the perfect tool selection for setting utility poles, working with asphalt patch or general construction backfill compacting job. FEATURES: Only 3 moving parts for low maintenance Reversible On/Off valve for Open and Closed Center systems (hose-end models) Rotate trigger spool for Open and Closed Center systems (valve on tube models) Kits with couplers and accessories included (as shown): REL-TMP-60V-FF: 60" tamper with valve on hose & couplers REL-TMP-60-FF: 60" tamper with hose & couplers REL-TMP-72-HWK: 72" tamper, valve on tube, whips & couplers Flow Range Pressure Pressure Port Return Port Foot Size BPM Input Flow Range Input Pressure Max. Back Pressure Optimum Flow Weight Length Width (at handles) 4-6 gpm 1,000-2,000 psi 9/16-18 SAE O-Ring 3/4-16 SAE O-Ring 2.5 x 8" kidney shaped 1,160 @ 5 gpm REL-BR-SERIES 45 OR 67 LB. HYDRAULIC BREAKER The REL-BR is a medium-duty T handle breaker designed for D.O.T and street maintenance, gas & water repair, utility construction, and general contracting applications. The REL-BR operates on open- or closed-center systems. Sold with a choice of 1-1/8" or 1-1/4" hex chuck. The feathering valve controls blow speed at startup making initial tool placement easy. 7-9 gpm (26-34 lpm) 1500-2000 psi (105-140 bar) 250 psi (17 bar) 8 gpm (30 lpm) 45 lbs. / 67 lbs. (30 kg) 27 in. (68 cm) 16 in. (41 cm) REL-TMP-60V Valve on Hose Above photos shown as kits with couplers and accessories installed: REL-45BR 45 lb. Model REL-67BR 67 lb. Model REL-TMP-72 Valve on Tube REL-TMP-60 Direct Coupled (No Valve) BREAKERS, TAMPERS & DRIVERS HYDRAULIC Steels for breaking, cutting and driving are available from your Reliable representative. MODELS: REL-BR45-112 ( 6 x 1-1/8 in. Steel Cap) REL-BR45-125 ( 6 x 1-1/4 in. Steel Cap) REL-BR67-112 ( 6 x 1-1/8 in. Steel Cap) REL-BR67-125 ( 6 x 1-1/4 in. Steel Cap) Please specify when ordering Operate from any 2,000 PSI Hydraulic Power Source Supplied with 18 inch whips and FF Couplers 109
BREAKERS, TAMPERS & DRIVERS HPB55-1AVS HPB45-1AVS HPB45-2AVS CP 1290 HPB45-1AVS BREAKER 45 LB 1-1/8x6 DMP HDL HPB45-2AVS BREAKER 45 LB 1x4-1/4 DMP HDL HPB55-1AVS BREAKER 55LB 1-1/8x6 DMP HDL Great for breaking sidewalks and curbs or driving ground rod, and for other small demolition jobs Clean modular design with few protrusions to irritate operators legs High blow energy provides maximum breaking power Integral rubber damper reduces chisel noise AVS tools have patented spring-dampened handles that reduce vibration transmitted to the operator by 80%-90% Two-step trigger Supplied with 12 in. (305 mm) steel braided whip hoses CP 1290 90 LB. PNEUMATIC BREAKERS Great for breaking heavy and reinforced concrete, frozen ground, asphalt, boulders and pavement Alloy steel forgings for excellent durability Equipped with four-bolt backhead to withstand rugged use Integral oiler for continuous lubrication Heavy-duty Polyurethane front head springs to reduce reaction back to operator Reversible piston reduces maintenance cost Air inlet swivel for easy maneuverability HYD. BREAKERS & ROCK DRILL HD20 HD20 HYDRAULIC POWERED ROCK DRILL Built in air compressor makes removes drill cuttings from the hole. With the turn of a knob this machine can be used as a pavement breaker and sign post anchor driver. Low noise as it uses hydraulics not air Closed circuit no exhaust from the tool Equivalent to 55 pound air drill Anti-vibration handles reduce operator fatigue Hundreds of available tools for drilling, driving or breaking Drives round, U-Channel, Square post anchors Breaks concrete, asphalt Drills up to 3" diameter in concrete or rock MODEL HPB45-2AVS HPB45-1AVS HPB55-1AVS CP 1290 HD20 Dimensions 26-1/2" Length 28-1/2" Length 30" Length 29" Length 22" x 16" Connection 1/2" NPTF 1/2 NPTF 1/2 NPTF 3/4 NPT Air Inlet 3/8" Hose Impact Energy 63 ft.-lb. 65 ft.-lb. 81 ft.-lb. 50 ft.-lb. Shank Size 1" x 4-1/4" 1/8" x 6" 1/8" x 6" 1-1/8" x 6" 7/8" x 4-1/4" Blows Per Minute 2160 2160 1860 1100 1200 Weight 47 lbs. 54 lbs. 56 lbs. 82 46 110 QUALITY I EXPERIENCE I PROFESSIONALISM I DEDICATION
QUALITY I EXPERIENCE I PROFESSIONALISM I DEDICATION PAVING BREAKER TOOLS MOIL POINT A11014 14" 3.4 lbs. A21014 14" 4.5 lbs. A31014 14" 5.9 lbs. A41014 14" 7.2 lbs. A11018 18" 4.3 lbs. A21018 18" 5.8 lbs A31018 18" 7.1 lbs A41018 18" 8.8 lbs A11024 24" 5.2 lbs. A21024 24" 6.8 lbs A31024 24" 8.9 lbs A41024 24" 10.9 lbs A11036 36" 7.5 lbs. A21036 36" 9.3 lbs A31036 36" 12.3 lbs A41036 36" 15.5 lbs A21048 48" 12.7 lbs A31048 48" 15.9 lbs A41048 48" 19.7 lbs A21060 60" 15.1 lbs A31060 60" 19.4 lbs A41060 60" 24.0 lbs A21072 72" 18.7 lbs A31072 72" 23.0 lbs A41072 72" 28.4 lbs A21096 96" 24.6 lbs A31096 96" 30.0 lbs A41096 96" 37.1 lbs PAVING BREAKER TOOLS NARROW CHISEL A12014 14" 3.4 lbs. A22014 14" 4.5 lbs. A32014 14" 5.9 lbs. A42014 14" 7.2 lbs. A12018 18" 4.3 lbs. A22018 18" 5.8 lbs A32018 18" 7.1 lbs A42018 18" 8.8 lbs A12024 24" 5.2 lbs. A22024 24" 6.8 lbs A32024 24" 8.9 lbs A42024 24" 10.9 lbs A12036 36" 7.5 lbs. A22036 36" 9.3 lbs A32036 36" 12.3 lbs A42036 36" 15.5 lbs A22048 48" 12.7 lbs A32048 48" 15.9 lbs A42048 48" 19.7 lbs A22060 60" 15.1 lbs A32060 60" 19.4 lbs A42060 60" 24.0 lbs A22072 72" 18.7 lbs A32072 72" 23.0 lbs A42072 72" 28.4 lbs A22096 96" 24.6 lbs A32096 96" 30.0 lbs A42096 96" 37.1 lbs PAVING BREAKER TOOLS 3" CHISEL A13014 14" 3.5 lbs. A23014 14" 5.2 lbs. A33014 14" 6.7 lbs. A43014 14" 8.1 lbs. A13018 18" 4.3 lbs. A23018 18" 6.2 lbs A33018 18" 7.9 lbs A43018 18" 9.5 lbs A13024 24" 5.5 lbs. A23024 24" 7.7 lbs A33024 24" 9.5 lbs A43024 24" 11.6 lbs A13036 36" 8.0 lbs. A23036 36" 10.6 lbs A33036 36" 12.9 lbs A43036 36" 15.7 lbs A23048 48" 13.6 lbs A33048 48" 16.2 lbs A43048 48" 20.4 lbs A23060 60" 16.5 lbs A33060 60" 20.1 lbs A43060 60" 25.6 lbs A23072 72" 19.5 lbs A33072 72" 23.2 lbs A43072 72" 29.3 lbs A23096 96" 25.4 lbs A33096 96" 30.6 lbs A43096 96" 388.0 lbs PAVING BREAKER TOOLS HI-DUTY POINT A14014 14" 4.1 lbs. A24014 14" 4.1 lbs. A34014 14" 6.8 lbs. A44014 14" 8.0 lbs. A14018 18" 6.1 lbs. A24018 18" 6.1 lbs A34018 18" 8.0 lbs A44018 18" 9.6 lbs PAVING BREAKER TOOLS HI-DUTY CHISEL A15014 14" 4.1 lbs. A25014 14" 4.1 lbs. A35014 14" 6.8 lbs. A45014 14" 8.0 lbs. A15018 18" 6.1 lbs. A25018 18" 6.1 lbs A35018 18" 8.0 lbs A45018 18" 9.6 lbs BREAKERS, TAMPERS & DRIVERS PAVING BREAKER TOOLS PAVING BREAKER TOOLS 3" CHISEL A16014 14" 4.5 lbs. A26014 14" 5.5 lbs. A36014 14" 7.3 lbs. A46014 14" 8.2 lbs. A26018 18" 6.5 lbs A36018 18" 8.5 lbs A46018 18" 10.0 lbs 111
BREAKERS, TAMPERS & DRIVERS HYD. SIGN POST DRIVER DRIVE GAD R-SPD-DGS BASE VIEW Control Valve and FF Couplers Included 70 lbs. 30.5 in. X 8 in. X 9 in. REL-SPD ADAPTER REL-SPD REL-SPD HYDRAULIC SIGN POST DRIVER The REL-SPD Sign Post Driver will drive posts of almost any configuration, including U channel, round, square, T-post and more. The REL-SPD is fitted to accommodate most common post types, providing greater control throughout the post installation. Reducing operator fatigue due to indirect motion, and limiting damage to the top of the post. A balanced lifting eye, in-line control valve, and dual full length cushion grip handles simplify lifting and operation in raised applications. Optional post adapters are available to accommodate custom or regional post styles. The REL-SPD meets State Department of Transportation (DOT) requirements for driving breakaway posts and delineators. Capable of driving posts to within 4 inches (100 mm) above ground level. CAPACITIES REL-SPD without accessory adapters #2, #3 and #4 lb./ft. U Channel Sign Post #3 & # 4 Strong Back U Channel Sign Post #1 Delineator Post 2-1/2 in. (63.5 mm) Square Post 2-5/8 in. (67 mm) Round Post REL-SPD with accessory adapters 1-3/4" Round (T-Post) 1-3/4" Square Post 2" Round Pipe 2" Square Post 2-1/4" Square Post CUSTOM SIGN POST DRIVER ACCESSORIES Five custom Sign Post Adapters and one Drive Gad are available for use with the REL-SPD Sign Post Driver. When the custom sign post adapters are installed into the front housing of the driver it will provide a positive guide for the post. The adapter guarantees that the full force of the hammer falls squarely onto the end of the post. Less movement and increased drive force will result in the post being driven faster, cleaner and more true. R-SPD-DGS Drive Gad - The Drive Gad allows Break-Away posts to be driven to within 4 inches above ground level. Shape: Square, I.D. Size: 2"- 2-1/4" ADAPTERS 5 STYLES R-SPD-175R 1-3/4" Round R-SPD-200R 2" Round R-SPD-175S 1-3/4" Square R-SPD-200S 2" Square R-SPD-225S 2-1/4" Square 112 QUALITY I EXPERIENCE I PROFESSIONALISM I DEDICATION
QUALITY I EXPERIENCE I PROFESSIONALISM I DEDICATION REL-SPP HYDRAULIC SIGN POST PULLER The REL-SPP will pull flanged type and irregular shaped sign posts and poles up to 8 inches in diameter. Pull flanged type posts using the gripping jaw, or utilize the included chain to wrap around the pole. The REL-SPP combines 9,800 lbs. of pulling force with an 8 inch stroke to provide the power for almost any application. MODEL REL-SPP System Hydraulic Pressure 2,000 psi (140 bar) Flow Range 3-9 gpm (11-34 lpm) Pulling Force 9,800 lbs. (4,450 kg) @ 2,000 psi Capacity Up to 8 inch diameter (20 cm) Weight 70 lbs. Length 12.75 Width 14 Height 18.75 (Retracted) REL-EA250 HYDRAULIC AUGER POST HOLE DIGGER The REL-EA250 Hydraulic Earth Auger can be used in boring applications for pole, post, and fence installations. The X Handles offer easy two person operation. The Torque Anchor Bar offers safe one person operation. The safety control valve is reversible, simplifying the augers removal from the hole. MODEL REL-EA250 Weight 47 lbs. (21 kg) w/o torque bar Length 11.7 in. (30 cm) w/o auger Width 46 in. (119 cm) w/ handles Performance 250 ft. lb. (339 Nm) Capacity (Long Auger) 2 to 18 in. Dia. x 42 in. (46 x 107 cm) + Extensions Flow Range 7 9 gpm (26-34 lpm) Pressure Up to 2,000 psi (up to 138 bar) Ports / Connection -8 SAE O-Ring / 3/8 in. FF Quick Couplers Torque Anchor Bar 75-141 in. (190-358 cm) Speed (at 8 gpm/30 lpm) 165 rpm Integrated Control Valve Couplers Included R-SPP-PIN Square Post Assist Pin Operate from any 2,000 PSI Hydraulic Power Source Shown with Optional Auger Features Gripping Jaw and Chain Operation to Handle Flanged and Irregular Poles up to 8 inches in dia. Stabilizer Bar Not Shown BREAKERS, TAMPERS & DRIVERS HYD. POST PULLER & AUGER 113