P600 (MS-16D3) Disassembly Guide 1 BATTERY PACK 2 BOTTOM DOOR ASSY 3 HDD MODULE 4 ODD MODULE 5 THERMAL-KIT AND RAM 6 SEPARATE UPPER CASE AND LOWER CASE 7 LOWER CASE ASSY 8 UPPER CASE ASSY 9 LCD MODULE ASSY
1 BATTERY PACK 1.1:Move the Unlock button base on left picture shows; 1.2:Release the Release button and move the battery pack base on left picture. Battery Pack S9N-3089200-SB3 1
2 BOTTOM DOOR ASSY 2.1:Remove the 10 screws (M2.5*4mm), then remove the Bottom door. Attention: the screw driver touque is: 2.3Kgf-cm Bottom door 307-6D2J211-SE0 1 Screw E43-1254002-H29 10
3 HDD MODULE 3.1:Remove the 3 screws (M2.5*4mm); Then remove the HDD Module according to the direction as pic shows. Attention: the screw driver torque: 3.0Kgf-cm Screw E43-1254002-H29 3 3.2 : Remove the 2 screws (M3*3.5mm) that stabilize the bracket. Attention: the screw driver torque is 2.3Kgf-cm Screw E43-1303502-H29 2 3.3:Remove the HDD bracket. HDD Bracket 307-6910111-A89 1 HDD Module S71-2432538-W36 1
4 ODD MODULE 4.1: Remove the ODD Module according to the direction as pic shows. 4.2:Remove ODD Bezel as below. ODD Bezel 307-6D1F211-SE0 1 4.3:Remove 2pcs screws (M2*3mm). Then remove ODD Bracket as below. Attention: the screw driver torque: 2.3Kgf-cm Screw E43-1203003-H29 2 ODD Bracket E2M-6D10112-A89 1 ODD Module S7D-2170004-H44 1
5 THERMAL-KIT AND RAM 5.1:Remove the 3 screws(m2.5*4mm) and FAN cable, after that remove the Fan. Attention:the screw driver torque is 2.3Kgf-cm Screw E43-1254002-H29 3 Fan E33-0800140-A32 1 5.2:Remove the 3 screws(m2.5*4mm),after that remove the thermal module. Attention:the screw driver torque is 2.3Kgf-cm Screw E43-1254002-H29 3 HEATSINK E31-0801810-TA9 1 5.3:Push the two sides shielding of RAM as pic Shows, then remove the RAM module; after that remove the CPU. CPU A13-2220106-I06 1 RAM Module S7C-S458804-S02 1
6 SEPARATE UPPER CASE AND LOWER CASE 6.1:Remove 7 screws(m2*3mm) Attention: the screw driver torque is 2.3Kgf-cm Screw E43-1203003-H29 7 6.2:Remove 13 screws(m2.5*4mm) Attention: the screw driver torque is 2.3Kgf-cm Screw E43-1254002-H29 13
6 SEPARATE UPPER CASE AND LOWER CASE 6.3:Before remove K/B, firstly remove the upside, then remove the two sides, last remove the downside. 6.4 : Firstly push connector according to the direction as pic shows; then remove the cable; Keyboard S1N-3EUS231-SA0 1 6.5: When remove the keyboard should notice the two bosses at bottom of the keyboard..
6 SEPARATE UPPER CASE AND LOWER CASE 6.6:Remove the 1 screw(m2.5*4mm); Attention: the screw driver torque is: 2.0-2.5Kgf-cm Screw E43-1254002-H29 1 6.7:First release the connector that stabilize the cable, then remove Touchpad cable according to the direction that pic shows. 6.8:When remove the Upper case, detach the Upper case down side from Lower case;
7 LOWER CASE ASSY 7.1:Remove the Power cable and the LVDS cable as pic shows. 7.2:Remove 1 screw (M2.5*4mm); then remove the Power board. Attention: the screw driver torque is 2.0-2.5Kgf-cm Power Board 607-16D3C-01S 1 Screw E43-1254002-H29 1 7.3 : Remove the 3 screws (M2.5*4mm); then remove the Audio board. Attention: the screw driver torque is 2.0-2.5Kgf-cm Audio board 607-16D3B-01S 1 Screw E43-1254002-H29 3
7 LOWER CASE ASSY 7.4 : Remove the 5screws (M2.5*4mm), then remove the main board from the Lower case. Attention: the screw driver torque is 2.0-2.5Kgf-cm Main Board 607-16D31-01S 1 Screw E43-1254002-H29 5 7.5:Remove the cable as pic shows. 7.6 : Remove the 1 screw (M2.5*4mm); then remove the FFC and VGA board. Attention: the screw driver torque is 2.3Kgf-cm VGA board 607-16D3A-01S 1 Screw E43-1254002-H29 1
7 LOWER CASE ASSY 7.7:Remove the 1 screw (M2.5*4mm) that stabilize the left LCD hinge. Attention: the screw driver torque is 2.5-3.0Kgf-cm Screw E43-1254002-H29 1 7.8:Remove the 1 screw (M2.5*4mm) that stabilize the right LCD hinge. Attention: the screw driver torque is 2.5-3.0Kgf-cm Screw E43-1254002-H29 1 7.9:Remove the Speaker module from lower case. Speaker Module S33-A000150-F33 1 Lower Case 307-6D1D211-SE0 1
8 UPPER CASE ASSY 8.1:Remove the 2 screws (M2*3mm), then remove the T/P bracket. Attention: the screw driver torque is 1.5-2.0Kgf-cm T/P bracket E2M-6D10511-A89 1 Screw E43-1203003-H29 2 8.2:Remove the 2 screws (M2*3mm), then remove the F/P. Attention: the screw driver torque is 1.5-2.0Kgf-cm F/P OS1-16D3001 1 Screw E43-1203003-H29 2 8.3 : Remove the Mylar and release the connector that stabilize the T/P cable, then remove the T/P module according to direction of pic shows; T/P module S78-3700440-E47 1 UPPER CASE 307-6D1C221-SE0 1 FFC Cable (To MB) K1C-1012057-J36 1
9 LCD MODULE ASSY 9.1:Remove the two sides LCD HINGE-CAP. Hinge cap-l E2P-6910151-H76 1 Hinge cap-r E2P-6910251-H76 1 9.2:Remove the 6 LCD rubbers. LCD Rubber E2Y-6911711-Y40 6 9.3:Remove the LCD bezel, should begin from downside to left side, then the upside to right side; LCD Bezel 307-692B211-U22 1
9 LCD MODULE ASSY 9.4:Remove the 3 magnets on LCD cover; LCD Cover Magnet E2M-6910511-SF7 2 LCD Cover Magnet E2M-6910411-SF7 1 9.5:Remove the 3 screws (M2.5*5mm); Remove the left LCD hinge. Attention: the screw driver torque is 3.0-3.5Kgf-cm Screw E43-1255002-H29 3 Hinge L E2M-6D10911-G60 1 9.6:Remove the 3 screws (M2.5*5mm); Remove the right LCD hinge. Attention: the screw driver torque is 3.0-3.5Kgf-cm Screw E43-1255002-H29 3 Hinge R E2M-6D10811-G60 1
9 LCD MODULE ASSY 9.7:Remove the 4 screws (M2.5*4mm) Attention: the screw driver torque is 2.0-2.5Kgf-cm Screw E43-1254002-H29 4 9.8:Firstly remove the Camera Cable, then remove the display module from LCD cover. 9.9:Remove the LVDS cable from display module; LVDS Cable K19-3023011-V03 1
9 LCD MODULE ASSY 9.10:Remove the 8 screws (M2*3mm) Attention: the screw driver torque is 1.5-2.0Kgf-cm Display Module S1J-642G004-CG1 1 LCD BRACKET-L E2M-6910211-A89 1 LCD BRACKET-R E2M-6910311-A89 1 Screw E43-1203003-H29 8 9.11:Remove the CMOS camera module according to the sequence as pic shows; Camera Module S1F-0001550-AH3 1
9 LCD MODULE ASSY 9.12:Remove the MIC Module as left picture show MIC Module S34-2101070-K03 1 9.13:Remove the WIRELESS board from LCD Cover. Antenna S79-1800U40-J51 1 9.14:Remove the Bluetooth board from LCD Cover. Bluetooth 605-3801-010 1 LCD Cover 307-691A713-SE0 1
P600(MS-16D3)Screws specification Photo Screw specification Label (M2.5*L4MM)black (M2.5*L5MM)white (M2*L3MM)white (M3*L3.5MM) white
P600(MS-16D3)screws specification 1 BOTTOM DOOR ASSY total 22pcs screws specification: Photo Screw specification label (M2.5*L4MM) black
2 THERMAL-KIT 6pcs screws specification: P600(MS-16D3)screws specification Photo Screw specification label (M2.5*L4MM) black
P600(MS-16D3)screws specification 3 ODD and HDD ASSY total 4pcs screws specification: Photo Screw specification label (M3*L3.5MM) white (M2*L3MM)white
P600(MS-16D3)screws specification 4 LOWER CASE ASSY total 9pcs screws specification: Photo Screw specification label (M2.5*L4MM) black (M2*L3MM)white
P600(MS-16D3)screws specification 5 LCD Hinge total 2pcs screws specification: Photo Screw specification Label (M2.5*L4MM) black
P600(MS-16D3)screws specification 6 LCD MODULE ASSY total 18pcs screws specification: Photo Screw specification label (M2.5*L4MM) black (M2.5*L5MM)white (M2*L3MM)white
P600(MS-16D3)screws specification 7 TOUCHPAD total 4pcs screws specification: Photo Screw specification label (M2*L3MM) white