Medium voltage switchgear type W rated voltage kv rated current 0 A
General The metal-encapsulated, air-insulated medium voltage switchgears, type W are for universal application. They range from compact ring cable switchgears up to complex power distribution switchgears. Tailored to meet the needs of public utility networks and power supply companies in industry and municipal buildings. These medium-voltage switchgears meet the user s specific requirements in full and ensure a satisfactory power distribution. The W standard types are available in three different dimensional sizes: W 0; w x d x h: 00 x 0 x 00 mm, W ; w x d x h: 0 x 0 x 00 mm, W 0; w x d x h: 00 x 0 x 00 mm. They are available as individual s or as a combined switchgear, where the equipment, sequence etc. can be determined by the customer. The switch s are type-tested in compliance with DIN VDE 00, Part, including the Pehla directive No.. Operating conditions The switch s of type W are installed in closed electrical operating areas which are only to be entered by skilled personnel and appropriately instructed persons. The equipment can be used at an altitude of up to 000 m above sea level. For installations above an altitude of 000 m the rated insulating level of the switchgear must be corrected accordingly. The switch s are designed for use under normal operating conditions in compliance with the standard DIN VDE 00, Part 000(IEC ). Technical standards The design of the air-insulated switch s corresponds to the specifications of the DIN VDE 00, Part. The resistance to accidental arcs of the switch s has been determined at ka and 0 ka; s, by and independent testing institute. The installed switchgear equipment is designed in compliance with DIN VDE 00, Part 000 (IEC ). Technical data rated voltage rated frequency rated lightning impulse withstand voltage rated short-time withstand voltage rated short-circuit duration rated current s with circuit breaker V-0- KUF rated current s with load disconnector H rated short-time current s with circuit breaker V-0- KUF rated short-time current s with load disconnector H rated peak current s with circuit breaker V-0- KUF rated peak current s with load disconnector H degree of protection kv 0 Hz kv kv s 0 A 0 A ka 0 ka ka 0 ka IP X Description of the W switch s Design The air-insulated medium-voltage switch s of type W with a width of 00 mm, 0 mm and 00 mm are metal-encapsulated. The switch frame is made of a screwed, hot-galvanized composite structure. The front of the switch s has a single-wing door of steel sheet with door hinge optionally on the right or left. A window of compound glass is inserted in the door. The cover in front of the bus bar compartment is either screwed on or designed as a door for the relay box positioned behind it. Each switch has a screwed on rear of galvanized sheet metal. Connecting cables are conducted into the switch s from below and are mounted on cross rails. The doors and covers of the switchgear are painted in structural paint (available in different colours according to the customer s request).
Equipment The switch s of type W are available in the following versions: Cable switch WK Transformer feeder WT Measuring switch WM Bus sectionaliser WÜ Circuit-breaker WL All switch s are partitioned off from to, in the bus bar area, by means of fibrousglass reinforced plastic plates with lead-in openings. Pressure relief can be in upward or downward direction. Switch s equipped with load-break switches can optionally be fitted with an earthing switch as well. Integrated in the circuit-breaker, type WL, there is also a bus disconnector. It is also possible to equip these s with a set of current transformers and voltage transformers as well as with an earthing switch. The optional interlocking of the equipment practically rules out any form of incorrect operation. All built-in switchgear equipment can be operated manually or via motor-operated mechanisms when the door is closed. The product program is completed by special measuring s which are fitted with current and voltage transformers. Earthing switches or spherical fixed points are available for earthing and shortcircuiting. An insulating protective plate can be inserted when the door is closed. It is possible to install appropriate surge voltage protectors in the, if required. W switch s optional - not possible * not possible with current or voltage transformer WK WT WM WÜ WL WÜL Switch s W 0 Cable Transformer feeder Measuring Bus section. Circuit breaker Circ. br. bus sect. Disconnector * * - - Load disconnector / H H EA / EK H SEA - circuit breaker EK / EA / SEA V.. KUF V.. KUF Earthing switch - Current transformer - Voltage transformer - - - WK WT WM WÜ WL WÜL Switch s W, W 0 Cable Transformer feeder Measuring Bus section. Circuit breaker Circ. br. bus sect. Disconnector - - - - Load disconnector / H H EA / EK H SEA - circuit breaker EK / EA / SEA V.. KUF V.. KUF Earthing switch - - Current transformer - Voltage transformer - - Weights Panel type Description Weight [kg] W - 0 W - W - 0 WK cable switch 0 WT transformer feeder 0 0 WÜ bus sectionaliser 00 0 WM measuring switch 0 0 WL circuit-breaker 0 0 Auxiliary equipment insulating protective plate in compliance with DIN VDE 0 part illumination, floor coverings capacitive voltage testing system in compliance with DIN VDE 0 part, short-circuit indicators additional locking systems with profile cylinder and lockable operating mechanisms
Type W 0 switch s Positions: Pressure relief plate Relay box Bus terminal Switch-disconnector H Withdraw able plate Current transformer Voltage transformer Circuit breaker Position indicator and actuation of load-break switch 0 Position indicator and actuation of disconnecting switch Position indicator and actuation of earthing switch Earthing switch Disconnecting switch HV-HBC fuse Cable terminal Type W 0 switch front view Cable with H EA/EK load discon. also possible with current and voltage transf. 0 0 Cable with H EA/EK load disconnector and disconnector Transformer feeder with H SEA load disconnector, also possible with current and voltage transformer Transformer feeder with H SEA load disconnector and disconnector
Bus sectionaliser with H EA / EK load disconnector Bus sectionaliser with H SEA load disconnector Measuring with current and voltage transformers 0 Measuring in longitudinal rails with current and voltage transformers side and front view Circuit-breaker with circuit breaker and disconnector
Type W and W 0 switch s Type W and W 0 switch front view Cable (bus sectionaliser ) with H EK / EA load disconnector Cable with H EK / EA load disconnector, current and voltage transformer Measuring with current and voltage transformer Measuring in longitudinal rails with current and voltage transformer Transformer feeder (bus sectionaliser ) with H SEA load disconnector
0 0 0 Circuit-breaker (V-0- KUF) with current transformer Circuit-breaker (V-0- F) with current and voltage transformer Circuit-breaker (V-0- KUF) (bus sectionaliser ), also possible with current transformer Specifications are subject to change without notice. DRIBO 0/0