PD18-RIM INSTALLATION INSTRUCTIONS The PD18-RIM is a storefront grade 1 exit device equipped with motor driven latch retraction. Retrofits Adams Rite 8800 series. A. C. E. B. D. PD18-RIM Includes A. RIM Exit Device B. Hardware pack C. 5 Lead D. Lock Stile End Cap pack E. Hinge Stile End Cap pack Tools Required Cordless Drill Needle Nose Pliers Measuring Tape 1/8 Drill Bit 1/4 Drill Bit #25 Drill Bit U.S. Customer Support 1-888-622-2377 Visit our website for more details www.commandaccess.com 1 Canada Customer Support 1-855-823-3002 Doc # 20370_B
TECHNICAL INFORMATION Specifications Input Voltage:24VAV/DC or 12VAC/DC+/- 10% Solenoid Amperage 12V: 900mA Solenoid Amperage 24V: 450mA Wire gauge: Minimum 18 gauge Troubleshooting & Diagnostics Symptom Possible Cause Solution Solenoid pulls back but releases immediately Solenoid plunger not seating correctly - Check plunger rod adjustment. - Check vertical rod adjustment. - Make sure the plunger set screw has been installed correctly. Solenoid pulls back and holds, but does not retract latch far enough Plunger rod out of adjustment Check plunger rod adjustment Solenoid has excess delay time and/or drop out. Wire run exceeding the maximum recommended distance Locate power supply within the distances specified U.S. Customer Support 1-888-622-2377 Visit our website for more details www.commandaccess.com 2 Canada Customer Support 1-855-823-3002
Electrified Exit Device Installation Example CAT GREEN CHANNEL 1 LED Ceiling Tile NORMALLY OPEN DRY CONTACT FROM ACCESS CONTROL SYSTEM NO VOLTAGE LOCKING HARDWARE + - Legend Standard Placement Optional Placement RECOMMEND POWER SUPPLIES: All Command Access exit devices & field installable kits have been thoroughly cycle tested with Command Access power supplies at our factory. PS210 PS220/220B PS204/204B PS440B PS480B PS1 PS2/2B PS5-4 For more information click here or go to our website 3
DOOR SIZE 30 36 42 48 DIA 26.88 32.88 38.88 44.88 CUT-OFF INSTRUCTIONS FOR NON STANDARD DOORS 1. DRIVE OUT TWO ROLL PINS 2. REMOVE MOUNTING CAP 3. COLLAPSE BAR AND TAPE DOWN IN THE AREA OF CUT-OFF 4. DETERMINE EXTRUSION LENGTH (8 DIM) DIMENSIONS FROM RIVET CENTERLINE TO NEW CUT-OFF LENGTH 5. MEASURE MOUNTING BAR (NOT PUSH BAR) AND MARK EXTRUSION LENGTH ON TAPE 6. SAW OFF EXCESS LENGTH, REMOVE TAPE AND DE-BURR 7. LAY MOUNTING CAP OVER MOUNTING BAR AND USE AS GUIDE TO DRILL TWO 1/8 DIAMETER HOLES. 8. REINSTALL MOUNTING CAP INTO MOUNTING BAR AND DRIVE TWO ROLL PINS INTO HOLES. WHEN USED WITH OPTIONAL TRIM. REMOVE LOWER SCREW ONLY. MOUNTING BAR ROLL PINS 3.6 MIN PUSH BAR MOUNTING CAP DIM 8 DOOR OPENING MINUS 3.75 0.125 DIA HOLES (2 PLCS) DRILL.250 DIA HOLE (2 PLCS) MASKING TAPE SEPARATING PUSH BAR AND MOUNTING BAR PROCEDURE 1. REMOVE BOTH END CAPS. THE RETAINER IS ATTACHED TO THE NOSE CAP. 2. SLIDE PUSH BAR TOWARD HINGE SIDE OF DOOR. 3. CONTINUE TO SLIDE THE PUSH BAR PAST THE PIVOT PLATE THAT RIDES IN PUSH BAR TRACK. 4. SLIDE PUSH BAR IN OPPOSITE DIRECTION KEEPING PIVOT PLATE OUT OF TRACK UNTIL PUSH BAR IS FREE OF MOUNTING PLATE. END CAP MOUNTING BAR PUSH BAR PIVOT PLATE STOP PLATE END CAP & RETAINER ASS Y INSTALLING PUSH BAR TO MOUNTING BAR 1. WITH PUSH BAR IN HAND AND MOUNTING BAR ATTACHED TO DOOR, FIND STOP PLATE STAKED INTO PUSH BAR.( THIS PLATE IS ON THE LATCH END OF ASSEMBLED UNIT) SLIDE THE PIVOT PLATE NEAREST HINGE INTO TRACK OF PUSH BAR UNTIL SECOND PIVOT PLATE IS EXPOSED. INSERT PIVOT PLATE INTO TRACK ON PUSH BAR AND SLIDE IN OPPOSITE DIRECTION UNTIL PUSH BAR AND MOUNTING BAR ALIGN. 3.00 DRILL.250 DIA HOLES (2 PLCS) 1.50 CUT AWAY STOP (FOR HOLLOW STEEL JAMB, CONSULT FACTORY) METRIC EQUIVALENTS.219 5.56 1.500 38.10 38.88 987.55.250 6.35 1.531 38.89 42 1066.80.375 9.53 2.000 50.80 44.88 1139.95.406 10.31 3.00 76.20 48 1219.20.687 17.45 3.6 91.44 1/16 1.59.750 19.05 4.125 104.78 3/16 4.75.813 20.65 26.88 682.75 5/8 15.88 1.000 25.40 30 762.00 1 1/8 28.58 1.156 29.36 32.88 835.15 INSTALL INSTRUCTIONS INSIDE SURFACE CLOSED DOOR. DRILL.156 DIA PILOT HOLES FOR SELF TAPPING SCREWS (4 PLCS) 1. CRIMP ALL RIVNUTS IN STILE AND JAMB ACCORDING TO INSTRUCTIONS WITH RIVNUT TOOL. SKIP STEPS 2 AND 3 IF CYLINDER IS NOT USED. 2. INSTALL CYLINDER, USING SCREWS SUPPLIED WITH CYLINDER. 3. INSTALL MOUNTING BAR ( IF CYLINDER IS USED. BE SURE THAT TAILPIECE PROTRUDES 3/16 INCH TO ENGAGE CYLINDER PROP- ERLY.) 4. INSTALL PUSH BAR TO MOUNTING BAR. 5. INSTALL END CAPS 6. INSTALL STRIKE AND STRIKE PLUG. USE ENOUGH SPACERS SO THAT STRIKE CLEARS CAP BY 1/16 MOUNTING CENTER LINE #25 x 1 1/4 PAN HEAD SELF TAPPING SCREW (4 REQ D) #25 x 5/8 ROUND HEAD SELF TAPPING SCREW (4 REQ D) CYLINDER CENTER LINE STRIKE ASS Y SPACER (ONLY IF NEEDED) SPACER 1.531 1.000 2.000 WHEN USED WITH MULLION THIS SHOULD BE REFERENCED FROM STRIKE MOUNTING SURFACE. SEE MULLION TEMPLATE. 10-32 X 3/4 FLAT HEAD MACHINE SCREW RIVNUT A 1.375 1.500.750.687 WHEN USED WITH OPTIONAL TRIM, REMOVE LOWER SCREW ONLY.406.450.125.1.156 DIA (OUTSIDE ONLY).375.250.219 DIA THRU C SINK.375 DIA X 82 DEG. (2 PLCS).813.375 DIA NOTE: CYLINDER ACTUATOR MUST ALWAYS BE IN LOWER HOLE TO ENGAGE CYLINDER TALL PIECES 4
STRIKE PREPARATION AND INSTALLATION Instructions INSIDE SURFACE OF CLOSED DOOR 3/4 3/4 DRILL 5/32 DIA HOLE (2 PLCS) STRIKE SPACER (ONLY IF NEEDED) STRIKE 1 1/12 3 CUT AWAY STOP (FOR HOLOW STEEL JAMP. CONSULT FACTORY) STRIKE PLUG INSTALL STRIKE AND STRIKE PLUG. USE ENOUGH SPACERS SO THAT STRIKE STRIKE CLEARS END CAP BY 1/16 #10 X 1 1 1/8 SELF TAPPING SCREW 5