Installation Instructions for 99-7804B REV. 3/17/2015 INST99-7804B KIT FEATURES ISO DIN radio provision with pocket DDIN radio provision Painted two tone to match factory Retains factory color screen Honda Accord 2013-up 99-7804B KIT COMPONENTS A) Radio housing trim panel B) Brackets C) Top bracket D) Pocket E) (6) White panel clips F) (8) #6 x 3/8 Phillips screws G) (8) #8 x 3/8 Phillips screws H) Display retention interface and harness (not shown) A WIRING & ANTENNA CONNECTIONS (sold separately) Wiring Harness: Included Antenna Adapter: 40-HD11 B C D E F G Table of Contents Dash Disassembly Honda Accord 2013-up...2-3 Kit Assembly Kit preparation... 4 ISO DIN radio provision with pocket... 5 DDIN radio provision... 6 Wiring Instructions... 7-8 Touch Screen Instructions...9-10 TOOLS REQUIRED Panel removal tool Phillips screwdriver CAUTION: Metra recommends disconnecting the negative battery terminal before beginning any installation. All accessories, switches, and especially air bag indicator lights must be plugged in before reconnecting the battery or cycling the ignition. NOTE: Refer to the instructions included with the aftermarket radio. METRA. The World s best kits. 1-800-221-0932 metraonline.com COPYRIGHT 2015 METRA ELECTRONICS CORPORATION
Dash Disassembly 1. Unclip and remove the side trim panels from each side of the console. 2. Remove (2) Phillips screws exposed on pocket then remove the pocket. (Figure B) 3. Remove (2) 8 mm screws facing up on bottom of radio chassis inside pocket cavity. (Figure C) 4. Unclip and remove the small trim panel between the radio and steering column. (Models with auto climate will have a thermistor hose attached to this panel. Disconnect the hose under the dash above the gas pedal to give it enough slack before re-installing the panel.) (Figure D) Continue on next page (Figure C) (Figure B) (Figure D) 2
Dash Disassembly 5. Remove (2) Phillips screws on top of radio. (Figure E) 6. Unclip and remove the radio assembly. (Figure F) 7. Remove (1) Phillips screw from each A/C vent then unclip and remove the vents. (Figure G) 8. Remove (2) Phillips screws securing the hazard light switch and retain for kit assembly. Continue to kit assembly (Figure E) (Figure G) (Figure F) 3
Kit Preparation 1. Attach the hazard light switch to the radio trim panel using (2) of the supplied #8 x 3/8 Phillips screws. 2. Attach the (6) white panel clips to the radio housing trim panel. Continue on next page 4
Kit Assembly ISO DIN radio provision with pocket 1. Attach the radio brackets to the radio housing trim panel using (4) of the #6 x 3/8 Phillips screws. 2. Attach the top bracket to the top of the radio brackets using (4) of the #6 x 3/8 Phillips screws supplied. (Figure B) 3. Mount the pocket to the bracket/ panel assembly with (4) of the #8 x 3/8 Phillips screws supplied. (Figure C) 4. Slide the radio into the assembly and secure with screws supplied with the radio. (Figure D) 5. Attach the A/C vents to the radio trim panel and secure using (2) of the supplied #8 x 3/8 Phillips screws. (Figure E) 6. Locate the factory wiring harness in the dash. Follow the Wiring and Initialization section of this manual before completing the installation. 7. Mount the new radio assembly into the dash and reassemble dash in reverse order of disassembly. (Figure D) (Figure B) (Figure C) (Figure E) 5
ISO DDIN radio provision 1. Attach the radio brackets to the radio housing trim panel using (4) of the #6 x 3/8 Phillips screws. 2. Attach the top bracket to the top of the radio brackets using (4) of the #6 x 3/8 Phillips screws supplied. (Figure B) 3. Slide the radio into the bracket/ trim panel assembly and secure to the assembly using the screws supplied with the radio. (Figure C) 4. Attach the A/C vents to the radio trim panel and secure using (2) of the supplied #8 x 3/8 Phillips screws. (Figure D) 99-7804B Kit Assembly 5. Locate the factory wiring harness in the dash. Follow the Wiring and Initialization section of this manual before completing the installation. 6. Reassemble dash in reverse order of disassembly. (Figure C) (Figure B) (Figure D) 6
Wiring Instructions Harnesses Included: 24-pin gray Honda connector to 14-pin black interface connector, with pre-wired 12-pin black ASWC-1 harness. 24-pin and 12-pin gray Honda connector to 22-pin black interface connector, with a Yellow female RCA. 8-pin gray Honda subwoofer connector to White RCA. Blue connector to White connector LVDS cable. Connections to be made: From the 24-pin gray Honda connector to the aftermarket radio: Connect the Red wire to the accessory wire. Connect the Black wire to the ground wire. Connect the Yellow wire to the battery wire. Connect the Blue/White wire to the amp turn on wire (this wire must be connected to hear sound from the factory amplifier). Connect the White wire to the left front positive speaker output. Connect the White/Black wire to the left front negative speaker output. Connect the Gray wire to the right front positive speaker output. Connect the Gray/Black wire to the right front negative speaker output. Connect the Green wire to the left rear positive speaker output. Connect the Green/Black wire to the left rear negative speaker output. Connect the Purple wire to the right rear positive speaker output. Connect the Purple/Black wire to the right rear negative speaker output. 7
Wiring Instruction Connections to be made: From the 14-pin black connector to the aftermarket radio: Connect the Orange wire to the illumination wire. (If the aftermarket radio has no illumination wire, tape off the Orange wire). If Equipped with Factory Subwoofer: From the 8-pin gray Honda connector to the aftermarket radio: Connect the White RCA to the Subwoofer Output (a Y-RCA adapter may be needed, not provided). The following wires are for aftermarket multimedia/navigation radios that provide these wires (if not required, tape them off and disregard them): Connect the Light Green wire to the parking brake wire (if applicable). Connect the Blue/Pink wire to the speed sense wire (if applicable). Connect the Green/Purple wire to the reverse wire (if applicable). If not equipped with a factory Rearview Camera and one wants to be added: From the 22-pin black connector to the aftermarket radio: Connect the Yellow RCA to the aftermarket rearview camera (female to female barrel connector may be needed depending on camera brand, not provided). Note: If an aftermarket backup camera is connected it must be selected in the Menu. (Menu button on SWC>Camera Settings>Backup Camera Source>Aftermarket Backup Camera) ASWC-1 (if installing) After the interface is initialized, plug the ASWC-1 into the 12-pin harness of the 7804 and refer to the ASWC-1 instructions. Note: There are a couple harnesses in the vehicle that there will be no harness connections; these are not needed in the installation. Green and Gray connectors with similar small square connectors. 20-pin, 18-pin, & 5-pin gray connectors. 8
Touch Screen Instructions Initialization Personalization Menu Procedure When the interface first boots up, the OEM screen will show an Android Boot up sequence, DO NOT touch any controls until the clock screen appears. Enter the System settings menu to select the correct year range for the vehicle; the instructions to enter this menu are as follows. Press the Menu button on the SWC to enter the personalization menu then continue through the menus. (System Settings>Others>Select Car>2013 & 2014 Accord OR 2015 Accord) If this step is not done immediately after the boot sequence, the interface will need the power re-cycled by completely unplugging the interface, waiting 5-10 seconds, and re-attaching the harnessing. The steering wheel controls for the personalization menu will override the controls for the radio. Press the Menu button to enter the personalization menu To navigate through the menu you will continue to use the steering wheel controls. The controls are as follows: Volume up and down = Cycle through the menu options Source (SRC) = Enter Seek left = Back or Return Seek right = Not used The personalization menu is the same as the factory with a couple differences. 9
Touch Screen Instructions System Settings Camera Settings This menu option allows for a background change on the clock, the ability to adjust the clock, and select the year range for interface. This menu allows you to turn the LaneWatch camera on and off, change the view of the Rearview Camera, and allow you to add a aftermarket camera if the car is not equipped with a factory rearview camera. LaneWatch Calibration Note: The LaneWatch button is located on the left side of the steering wheel, on the stalk. Press and hold the LaneWatch button for 50 seconds to begin the LaneWatch aiming procedure (this procedure should only be done by a Honda authorized technician). At this point the display will also show an image of the LaneWatch camera feed, with instructions on what to do a Honda authorized technician will know what to do from here. 10
11
Installation Instructions for 99-7804B REV. 3/17/2015 INST99-7804B KNOWLEDGE IS POWER Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow. Metra recommends MECP certified technicians METRA. The World s best kits. 1-800-221-0932 metraonline.com COPYRIGHT 2015 METRA ELECTRONICS CORPORATION