1998 Pontiac Grand Am SMU - Revised Timing Chain, Sprockets, Tensioner Installation Procedure #00-06-01-002 - (Feb 9, 2000) Revised Timing Chain, Sprockets, Tensioner Installation Procedure 1998-1999 Chevrolet Malibu 1998-2000 Chevrolet Cavalier 1998-2000 Pontiac Grand Am, Sunfire 1998 Oldsmobile Achieva 1999-2000 Oldsmobile Alero 1998-2000 Toyota Cavalier with 2.4 L Engine (VIN T -- RPO LD9) This bulletin is being issued to revise the Timing Chain, Sprockets and Tensioner Installation Procedure. Please use the following to replace the existing information in the Engine Mechanical sub-section of the Engine Section in the 1998-2000 Service Manuals. Procedure 1. Install the camshaft sprockets. The sprockets are identical and interchangeable. 2. Clean the old sealer off of the bolts with a wire brush. 3. Clean the threaded hole in the camshaft with a nylon bristle brush.
4. Coat the camshaft bolts with Adhesive/Sealant Compound GM P/N 1234593 or equivalent. Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems. 5. Install the camshaft sprocket bolts and washers while holding the sprockets with J 39579. Tighten Tighten the bolts to 70 N m (52 lb ft). Important Ensure that the camshaft sprocket alignment pins are in the cylinder block and the timing chain housing, prior to installing the timing chain housing. The camshaft sprocket alignment pins ensure proper chain housing and front cover location for correct front oil seat to crankshaft alignment. 6. Install the J 36008-A through the holes in the camshaft sprockets and into the holes in the timing chain housing. This will position the camshaft for correct timing. 7. Use the following steps if the camshafts are out of position and must be rotated more than 1/8 turn in order to install the alignment dowel pins: A. The crankshaft must be rotated 90 degrees clockwise off of TDC to give the valves adequate clearance to open. B. Once the camshafts are in position and the dowels are installed, rotate the crankshaft counter clockwise back to TDC. Do NOT rotate the crankshaft clockwise to TDC. Valve or piston damage could occur.
Important The timing chain and crankshaft sprocket must be put in a specific direction for chain noise and wear considerations. The surfaces that were marked during removal should be showing when the chain and crankshaft sprocket are installed. 8. Install the timing chain over the exhaust camshaft sprocket around the coolant pump sprocket and around the crankshaft sprocket. 9. Remove the alignment dowel pin from the intake camshaft. Use the J 39579 in order to rotate the intake camshaft sprocket counter clockwise enough to allow the timing chain to slide over the intake camshaft sprocket. 10. Release the J 39579. The length of the chain between the two camshaft sprockets will tighten. 11. If properly timed, the intake camshaft alignment dowel pin will slide in easily. If the dowel pin does not fully index, the camshafts are not timed correctly and the procedure must be repeated. 12. Leave the alignment dowel pins installed. 13. The keyway on the crankshaft and the mark on the cylinder block should be aligned with the slack removed from the chain between the intake camshaft sprocket and the crankshaft sprocket. If the mark and the keyway are not aligned, move the chain one tooth forward or rearward. Remove the slack and recheck the marks.
Important Use the following steps in order to reset the timing chain tensioner assembly to the zero position: 14. Reset the timing chain tensioner assembly. A. Insert the tensioner plunger assembly into the tensioner housing. B. With the tensioner plunger fully extended, turn the complete assembly upside down on a bench or other flat surface. C. With the plunger face against the workbench, press firmly on the bottom of the tensioner housing. D. Compress the plunger until the plunger is seated flush in the tensioner. 15. Check the plunger to make sure that the plunger is out of the cylinder at the correct dimension. The correct dimension for the plunger to extend out of the cylinder is 1.7 mm (0.07 in) maximum. 16. Loosely install the tensioner assembly and bolts to the timing chain housing. 17. Install the timing chain tensioner shoe on the stud. 18. Apply hand pressure to the timing chain tensioner shoe until the locking tab seats in the groove in the stud. 19. Tighten the timing chain tensioner bolts. Do not over tighten. Tighten
Tighten the bolts to 10 N m (89 lb in). If the timing chain tensioner plunger is not released from the installation position, engine damage will occur when the engine is started. 20. Release the timing chain tensioner plunger. A. Using a flat blade screwdriver, cotter pin remover, or a similar tool, press firmly against the face of the timing chain tensioner plunger. Important If the timing chain tensioner plunger cannot be depressed, the plunger is not properly reset and the procedure for resetting the timing chain tensioner should be repeated. B. Depress the timing chain tensioner plunger until the plunger is bottomed out in the bore of the timing chain tensioner. C. Release the tensioner plunger. The plunger should press firmly against the back of the timing chain tensioner shoe. 21. Remove the J 36008-A from the camshaft sprockets. Beginning with the 1998 model year, the timing chain on the LD( (VIN T) Twin Cam Engine is different from the chain found on earlier versions of this engine, and is not to be replaced with a timing chain from earlier model year engines. The timing sprockets were also changed beginning in 1998, and the shape of the chain links matches the sprockets. Engine damage may result if the wrong timing chain is used. The timing chain and the crankshaft sprocket must be marked so that they are reinstalled in the same side facing out at the time of assembly. 22. Rotate the crankshaft clockwise two full rotations. Align the crankshaft keyway with the mark on the cylinder block and reinstall the alignment dowel pins. The alignment dowel pins will slide in easily if the engine is timed correctly.
23. Install the timing chain guides. GM bulletins are intended for use by professional technicians, NOT a "do-it-yourselfer". They are written to inform these technicians of conditions that may occur on some vehicles, or to provide information that could assist in the proper service of a vehicle. Properly trained technicians have the equipment, tools, safety instructions, and know-how to do a job properly and safely. If a condition is described, DO NOT assume that the bulletin applies to your vehicle, or that your vehicle will have that condition. See your GM dealer for information on whether your vehicle may benefit from the information. WE SUPPORT VOLUNTARY TECHNICIAN CERTIFICATION