Installation Instructions BEDPAN WASHER For Use with Exposed Flushometer and -/" Top Spud Toilets Certified to comply with: ASSE 07 CSA B. ADA Compliant 0 AS America, Inc. M960 607.800 607.8 MODEL NUMBERS 607.800 607.8 NOTE TO INSTALLER: Please give this manual to the customer after installation. To learn more about American Standard Faucets visit our website at: www.americanstandard.com or U.S. customer's e-mail us at: faucetsupport@americanstandard.com For Parts, Service, Warranty or other Assistance, please call -800--90 (In Canada: -800-87-069) (In Toronto Area only: -90-0609)
Thank you for selecting American-Standard...the benchmark of fine quality for over 00 years. To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. UNPACKING All American Standard Products Are Water Tested At Our Factory. Some Residual Water May Remain In The Valve During Shipping.. Remove the Bedpan Washer items from the carton. The illustration below shows all items after they have been removed from the carton. Some items may be packaged partially assembled to other items.. Flush Valve Assembly (optional) Must be purchased separately. Down Tube and Vacuum Breaker. Diverter assembly. Straight Tailpiece. Spud Coupling Nut and Washers 6. Spud Flange 7. Wall Support 8. Installation Instructions 9. -/" Offset Tailpiece CARE INSTRUCTIONS: DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH. DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A CLOTH WITH A COARSE SURFACE. 7 Installation Instructions BEDPAN WASHER For Use with Exposed Flushometer and -/" Top Spud Toilets Certified to comply with: ASSE 07 CSA B. ADA Compliant 0 AS America, Inc. 607.800 607.8 MODEL NUMBERS 607.800 607.8 8 9 M960 NOTE TO INSTALLER: Please give this manual to the customer after installation. To learn more about American Standard Faucets visit our website at: www.americanstandard.com or U.S. customer's e-mail us at: faucetsupport@americanstandard.com For Parts, Service, Warranty or other Assistance, please call -800--90 (In Canada: -800-87-069) (In Toronto Area only: -90-0609) 6 M960
Fig. Roughing-in Dimensions FINISHED WALL FINISHED WALL GENERAL DESCRIPTION: BEDPAN WASHER For Use with Exposed Flushometer and -/" Top Spud Toilets ADJUSTABLE 07mm (8-/8") MAX. mm (-/6") 8mm (-/6") mm (8-/") FOR -/" TOP SPUD FIXTURES 8mm (-/") OFF-SET TAILPIECE RECOMMENDED TOOLS; Fig...... Flat Blade Screwdriver Smooth Jaw Adjustable Wrench Tape Measure Tubing Cutter File Fig. 0' PRIOR TO INSTALLATION IMPORTANT: All plumbing must be installed in accordance with applicable codes and regulations. Water supply lines must be sized to provide an adequate volume of water for each fixture. Water pressure over 80 psi is not recommended with most plumbing fixtures Flush all water lines prior to operation. DO NOT use pipe sealant or plumbing grease on any coupling! Protect the chrome or special finish on the Bedpan Washer. DO NOT USE toothed tools on finished surfaces to install or service these valves. Also see Care and Cleaning section of this manual. M960
INSTALL TAILPIECE and DOWN TUBE with VACUUM BREAKER; Fig.. Slide the COUPLING NUT () onto the TAIPIECE ( or a). Place SEAL WASHER () with the tapered side facing down into the COUPLING NUT ().. Thread and tighten COUPLING NUT () to DIVERTER ASSEMBLY (). Fig.. Slide COUPLING NUT (a) onto the DOWN TUBE (). Place SEAL WASHER (a) with the tapered side facing up into the COUPLING NUT (a).. Thread and tighten COUPLING NUT (a) to DIVERTER ASSEMBLY (). TAPERED SIDE UP a a TAPERED SIDE DOWN -/" OFF-SET TAILPIECE OR a INSTALL SPUD FLANGE COUPLING; Fig.. Place the SPUD FLANGE () over the spud on the Fixture.. Thread SPUD COUPLING NUT () onto Spud. Make sure SEAL WASHER () and FRICTION WASHER () are installed. Do not tighten fully. Fig. -/" TOP SPUD M960
INSTALL BEDPAN WASHER; Fig.. Install BEDPAN WASHER ASSEMBLY () into SPUD ASSEMBLY () on fixture. Push the ASSEMBLY () down until the TAILPIECE () seats on the internal stop. Do not fully tighted SPUD COUPLING NUT (). Fig.. TAILPIECE () may be cut to obtain the correct rough-in dimensions for flush valve. INSTALL FLUSH VALVE; Fig. 6 Note: Flush valve () not included with Bedpan Washer and must be purchased separately. Fig. 6. Install FLUSH VLAVE () per manufactures instructions. M960
INSTALL SUPPORT BRACE; Fig. 7 Fig. 7. Determine required length of SUPPORT BRACE () by measuring the distance between finished wall and back of the DIVERTER VALVE () at support rod hole. Add /" (6mm) to the length determined and cut the SUPPORT ROD () to size.. Rotate the DIVERTER VALVE () to allow threading SUPPORT ROD () into back of diverter body. Slide wall SUPPORT ROD FLANGE () onto SUPPORT ROD () and rotate the DIVERTER VALVE () so that the wall SUPPORT ROD FLANGE () is flush with the wall.. Using the SUPPORT ROD FLANGE (), mark the two holes on the finished wall for the mounting screws and anchors. Rotate the DIVERTER VALVE () to the side and drill two /6" holes in the finished wall -/" deep.. Rotate the DIVERTER VALVE () and align the SUPPORT ROD FLANGE (). Secure the FLANGE with two Anchors and Screws (not provided). Tighten SET SCREW (). X+/" (6mm) ANCHORS CUT THIS END SCREWS FINISHED WALL X+/" (6mm) 6 TEST INSTALLAED BEDPAN WASHER; Fig. 8. Align FLUSH VALVE () and DIVERTER VALVE ASSEMBLY () and fully tighten all connections.. Push the DIVERTER ARM and SPRAY () down, parallel to the toilet rim. Flush the toilet to activate the SPRAY (). Fig. 8. Check all connections for leaks.. Return the DIVERTER ARM and SPRAY () to the up-right position. M960
BEDPAN WASHER MODEL NUMBERS 607.800 607.8 M969-0070A VACUUM BREAKER REPAIR KIT M9698-000A VACUUM BREAKER ASSEMBLY M969-0070A SPRAY FACE KIT M9606-000A SUPPORT BRACE M960-0070A DIVERTER REBUILD KIT M9696-000A DIVERTER ASSEMBLY COMPLETE M9607-0070A SPRAY ARM SEAL KIT M9608-000A COUPLING KIT M960-000A SCREWS M960-000A -/" OFF-SET TAILPIECE M9697-000A STRAIGHT TAILPIECE M969-000A ESCUTCHEON KIT HOT LINE FOR HELP For toll-free information and answers to your questions, call: (800) -90 Weekdays 8:00 a.m. to 6:00 p.m. EST IN MEXICO 0-800-89-00 IN CANADA -800-87-069 (TORONTO -90-06-09) Weekdays 8:00 a.m. to 7:00 p.m. EST Product names listed herein are trademarks of AS America, Inc. AS America, Inc. 0 6 M960