Technical Service BULLETIN September 14, 2001 00 02 Model Year BO023-01 BODY Introduction Toyota customers who find it necessary to increase the length of their seat belts may obtain Seat Belt Extenders at no cost through their local Toyota dealer. The extender is available in 6 inch, 9 inch, 12 inch, 15 inch and 18 inch lengths. The extender is available only in black. Owners are informed of the Seat Belt Extender availability through the Toyota Owner s Manual included in each vehicle. Seat Belt Extender The customer (individual requiring the extender) must visit a Toyota dealership to have the required measurements made and to complete the Seat Belt Extender Worksheet. The worksheet will allow the proper fitting and selection of a Seat Belt Extender for the customer. The dealership personnel should then determine the applicable part number and place a Critical Order through the TDN Parts Network or Dealer Daily. The dealership service department should complete the affixed Seat Belt Extender Customer Information Label on the part and review the Owner Instruction Sheet with the customer. The dealership should give a copy of the completed worksheet to the customer and keep the original in the customer s file. To assure utmost owner satisfaction, it is recommended that a dealership designate one person to coordinate all activities related to the Seat Belt Extender issue. It is recommended that dealerships do NOT stock Seat Belt Extenders due to the need for proper fitting to individual customers. This bulletin contains the following information: Procedure and Sample Label.......... Page 2 Application Charts.................... Pages 3 4 Part Number Information.............. Page 5 Owner Instructions................... Page 6 Seat Belt Extender Worksheet......... Page 7 Applicable Vehicles 2000 through 2002 model year Toyota vehicles. Warranty Information OP CODE DESCRIPTION TIME OPN T1 T2 N/A Not Applicable to Warranty Toyota Supports ASE Certification
Procedure 1. Owner requests a Seat Belt Extender from dealer. 2. Dealer verifies the need for a Seat Belt Extender and obtains a current copy of this TSB and copies the Worksheet. 3. Dealer measures the customer and completes the Worksheet. Dealer determines the correct part number and places a Critical Order for the part through the TDN Parts Network or Dealer Daily. 4. Dealer receives Seat Belt Extender and calls the customer in to check fit of the part. 5. If the Seat Belt Extender fit is good, dealership personnel completes the Customer Information Label on the part, explains usage of the part, and gives the customer a copy of the completed Worksheet. 6. Dealer places copy of the completed Worksheet in the customer s records. DEALER PARTS SUPPLY DEALER OWNER Sample Seat Belt Extender Customer Information Label CAUTION THIS SEAT BELT EXTENDER IS TO BE USED ONLY BY: ON VEHICLE: VIN: SEATING POSITION: USE BY OTHERS, OR IN ANOTHER SEATING POSITION, OR IN ANOTHER VEHICLE COULD REDUCE SEAT BELT RESTRAINT IN AN ACCIDENT AND RESULT IN PERSONAL INJURY.
Front Seat Belt Extender Applications FRONT SEAT EXTENDER APPLICATION MODEL TYPE 02 01 00 RAV4 R 5 R 5 R 5 RAV4 EV R 5 R 5 R 5 ECHO K 5 K 5 K 5 COROLLA TMMC PRODUCTION NUMMI PRODUCTION PRIUS N 7 N 7 MR2 SPYDER N 7 N 6 N 6 CELICA LIFTBACK & COUPE N 7 N 6 N 6 CAMRY TMC PRODUCTION TMMK PRODUCTION CAMRY SOLARA COUPE CONVERTIBLE AVALON* T 1 T 1 T 1 SIENNA TACOMA* S 2 S 2 S 1 4RUNNER K 5 K 5 K 5 LAND CRUISER K 5 K 5 K 5 SEQUOIA Q 4 Q 4 TUNDRA* HIGHLANDER R 5 R 5 * The extender must not be used for the center seat of Avalon, Tacoma, and Tundra which have bench seats.
Rear Seat Belt Extender Applications REAR SEAT EXTENDER APPLICATION MODEL TYPE 02 01 00 RAV4 W/TOKAI RIKA R 5 R 5 R 5 *1 W/QSS Q 4 *2 RAV4 EV ECHO R 5 R 5 R 5 COROLLA TMMC PRODUCTION NUMMI PRODUCTION T 1 T 1 T 1 PRIUS N 7 N 7 CELICA LIFTBACK & COUPE N 7 N 6 N 6 CAMRY TMC PRODUCTION TMMK PRODUCTION CAMRY SOLARA COUPE CONVERTIBLE AVALON T 1 T 1 T 1 SIENNA TACOMA XTRACAB T 1 T 1 A 2 DOUBLE CAB S 2 S 2 4RUNNER R 5 R 5 R 5 LAND CRUISER K 5 K 5 K 5 SEQUOIA REAR SEAT #1 T 1 T 1 REAR SEAT #2 Q 4 Q 4 TUNDRA ACCESS CAB HIGHLANDER R 5 R 5 *1 This seat belt was supplied by TOKAI RIKA. Make sure that the I/D mark on the back side of the seat belt buckle is the same as shown. *2 This seat belt was supplied by QSS. Make sure that the I/D mark on the back side of the seat belt buckle is the same as shown. NOTE: The seat belt extender must not be used for the center rear seat belt.
Part Number Information PART NUMBER PREFIX: 73399 LENGTH SERIES 6 INCH 9 INCH 12 INCH 15 INCH 18 INCH R 5 16060 16070 16080 16090 16100 N 1 12060 12070 12080 12090 12100 N 5 20110 20120 20130 20140 20150 N 6 20160 20170 20180 20190 20200 N 7 47010 47020 47030 47040 47050 K 5 35010 35020 35030 35040 35050 A 2 01060* 01070 01080 01090 01100 Q 2 06010 06020 06030 06040 06050 Q 4 0W010 0W020 0W030 0W040 0W050 S 1 04010 04020 04030 04040 04050 S 2 04060 04070 04080 04090 04100 T 1 01110 01120 01130 01140 01150 * Length: 7-1/4
Owner Instructions Failure to follow the recommendations indicated below could result in reduced effectiveness of the seat belt restraint system in case of vehicle collision, causing personal injury. The Seat Belt Extender must not be used: a. By anyone other than for whom it was provided (name recorded on seat belt extender). b. In any vehicle and/or seat position other than the one for which it was provided. c. When the Seat Belt Extender is provided for rear seat positions (with automatic locking retractor), make sure the retractor is locked when in use. If your seat belt cannot be fastened securely because it is not long enough, a personalized Seat Belt Extender is available from your Toyota dealer free of charge. Please contact your local Toyota dealer so that the dealer can order the proper required length for the extender. Bring the heaviest coat you expect to wear for proper measurement and selection of length. Additional ordering information is available at your Toyota dealer. CAUTION: When using the Seat Belt Extender, observe the following. Failure to follow these instructions could result in reduced effectiveness of the seat belt restraint system in case of vehicle accident, increasing the chance of personal injury. Never use the Seat Belt Extender if you can COMFORTABLY fasten the seat belt without it. The Seat Belt Extender must never be used with any child safety seats. Remember that the extender provided for you may not be safe when used on a different vehicle, or for another person or at a different seating position than the one originally intended for. To connect the extender to the seat belt, insert the tab into the seat belt buckle so that the PRESS signs on the buckle-release buttons of the extender and the seat belt are both facing outward as shown. Seat Belt Release You will hear a click when the tab locks into the buckle. When releasing the seat belt, press on the buckle-release button on the extender, not on the seat belt. This helps prevent damage to the vehicle interior and extender itself. Seat Belt Extender When not in use, remove the extender and store in the vehicle for future use.
SEAT BELT EXTENDER WORKSHEET PLEASE COPY THIS ORIGINAL WORKSHEET FOR EACH EXTENDER NEEDED CAUTIONS: To minimize the chance and/or severity of injury in an accident, the Seat Belt Extender must only be used: 1 By the person for whom it was provided. 2 In the seat position for which it was provided. The Seat Belt Extender must never be used with any child safety seats. When the Seat Belt Extender is provided for rear seat positions (with automatic locking retractor), make sure the retractor is locked when extender belt is in use. DEALER SEAT BELT EXTENDER APPLICATION APPLICANT DEALER CODE DEALER NAME APPLICANT NAME ADDRESS ADDRESS CITY & STATE ZIP CITY & STATE ZIP PHONE EMPLOYEE NAME MODEL YEAR BODY TYPE SEATING POSITION VEHICLE IDENTIFICATION NUMBER DIRECTIONS FOR DETERMINING PROPER EXTENDER LENGTH 1. Place the seat in the position the applicant normally uses. 2. With the applicant in the seat, wearing the thickest coat expected to be worn, pull belt all the way out and try to buckle belt. If belt latches into buckle and feels comfortable against upper chest area, an extender is not needed. If belt does not buckle, continue with Step 3. If buckle latches but belt has no slack remaining, continue with Step 3. 3. Measure distance between applicant s navel and seat belt buckle (Dimension A) and enter on Worksheet. 4. With belt all the way out, measure distance between latch tip and buckle tip (Dimension B) and enter on Worksheet. NOTE: If belt latches but there is no slack enter zero as Dimension B. 5. Subtract Dimension B from Dimension A and record number in Check Number box on Worksheet. 6. Seat Belt Extender length is Dimension B rounded up to next extender length (without exceeding Check Number). NOTE: If extender length exceeds Check Number, an extender cannot be provided to the customer. Dimension A: NAVEL TO BUCKLE Dimension B: LATCH TO BUCKLE Navel Latch Buckle A Buckle B SEAT BELT EXTENDER CALCULATION DIMENSION A: DIMENSION B: CHECK NUMBER: SEAT BELT EXTENDER AUTHORIZATION The same Seat Belt Extender can be used for right and left seating applications. Each Seat Belt Extender will have a label identifying the owner, VIN and seating position. Seat Belt Extenders are available only in black. Applicant s Signature: Date: (Actual user of seat belt extender)