Dr.Babasaheb Ambedkar Technological University, Lonere List of Equipment to be purchased under Shopping mode TEQIP II Last date for receipt of quotations: 5/2/25 Time 4:00 pm Dr.Babasaheb Ambedkar Technological University, Lonere invites sealed quotations for various items in the university departments through Shopping modes of purchase under TEQIP II scheme. You are invited to submit your most competitive quotation for the following goods with item wise detailed specifications given at Annexure I, 1. Government of India has received a credit from the International Development Association (IDA) towards the cost of the Technical Education Quality Improvement Programme [TEQIP]-Phase II Project and intends to apply part of the proceeds of this credit to eligible payments under the contract for which this invitation for quotations is issued. 2. Quotation: 2.1 The contract shall be for the full quantity as described above. 2.2 Corrections, if any, shall be made by crossing out, initialing, dating and re writing. 2.3 All duties and other levies payable by the supplier under the contract shall be included in the unit price. 2.4 Applicable taxes shall be quoted separately for all items. 2.5 The prices quoted by the bidder shall be fixed for the duration of the contract and shall not be subject to adjustment on any account. 2.6 The Prices should be quoted in Indian Rupees only. 3. Each bidder shall submit only one quotation. 4. Quotation shall remain valid for a period not less than 30 days after the last date of quotation submission. 5. Evaluation of Quotations, The Purchaser will evaluate and compare the quotations determined to be substantially responsive i.e. which 5.1 are properly signed ; and 5.2 confirm to the terms and conditions, and specifications. 6. The Quotations would be evaluated for all items together. 7. Award of contract:
The Purchaser will award the contract to the bidder whose quotation has been determined to be substantially responsive and who has offered the lowest evaluated quotation price. 7.1 Notwithstanding the above, the Purchaser reserves the right to accept or reject any quotations and to cancel the bidding process and reject all quotations at any time prior to the award of contract. 7.2 The bidder whose bid is accepted will be notified of the award of contract by the Purchaser prior to expiration of the quotation validity period. The terms of the accepted offer shall be incorporated in the purchase order. 8. Payment shall be made in Indian Rupees as follows: Delivery and Installation - 90% of total cost Satisfactory Acceptance - 10% of total cost 9. All supplied items are under warranty of 12 months from the date of successful acceptance of items. 10. You are requested to provide your offer latest by 15:00 hours on 05-Feb-25. 11. Detailed specifications of the items are at Annexure I. 12. Training Clause (if any) Required for operation. 13. Testing/Installation Clause (if any) Installation required 14. Information brochures/ Product catalogue, if any must be accompanied with the quotation clearly indicating the model quoted for. 15. Sealed quotation to be submitted/ delivered at the address mentioned below, Vidyavihar, Po. Lonere Tal. Mangaon, Dist. Raigad MS 402 103 17. We look forward to receiving your quotation and thank you for your interest in this project.
ANNEXURE I To: FORMAT FOR QUOTATION SUBMISSION (In letterhead of the supplier with seal) Date: Sl. No. Description of goods (with full Specifications) Qty. Unit Quoted Unit rate in Rs. (Including Ex Factory price, excise duty, packing and forwarding, transportation, insurance, other local costs incidental to delivery and warranty/ guaranty commitments) Total Price (A) Sales tax and other taxes payable In In figures % (B) Total Cost Gross Total Cost (A+B): Rs. We agree to supply the above goods in accordance with the technical specifications for a total contract price of Rs. (Amount in figures) (Rupees amount in words) within the period specified in the Invitation for Quotations. We confirm that the normal commercial warranty/ guarantee of months shall apply to the offered items and we also confirm to agree with terms and conditions as mentioned in the Invitation Letter. We hereby certify that we have taken steps to ensure that no person acting for us or on our behalf will engage in bribery. Signature of Supplier Name: Address: Contact No:
List of items to be purchased Sr. No. Teqip Package Code Equipment detail 1 Mech 81 High speed Camera High Speed Camera Make = Photron / Redlake / IDT Vision or equivalent Recording speed = 3000 fps @ maximum resolution and upto 1,00,000 fps at reduced resolution Maximum Resolution = 1024 x 1024 Pixel Size = 12 x 12 Internal Memory = upto 16 GB Sensor = 12 Bit CMOS Communication Interface = 1000 Base T Ethernet & USB Software Interface with 32/64 bit Windows OS Minimum Exposure Time = 1 µs Application: High speed dynamic impact testing of biological soft tissues and high speed image capturing in metal working phenomema 2 Mech 82 Deer Freezer Capacity = upto 170 lit. Temperature Range = Ambient to -80 0C No. of trays = 2 or 4 (Custom) Application = Biological Research 3 Mech 83 Digital Storage Oscilloscope Make = Tektronix/Agilent / Rigol or equivalent Bandwidth = Upto 200 MHz No. of Channels = 2 / 4 Sampling Rate = 1 GSa/s 25 GSa/s Memory = 8 12 MB Deep Memory Display = 7 Color LCD Display Recoding Length = 20 Kpts 1 Mpts Interface Connectivity = USB, Parallel & RS232, Laptop, printer & projector connectivity support Application: Strain gauge data acquisition in high speed dynamic testing 4 Mech 85 Steam Turbine Test Rig 1.Rankin Blade: - Thermal Efficiency on Turbine 2.Steam Boiler: - IBR 12 Kg/sq m 3.Pressure: - Fully automated, Oil fired comes with all safety devices. 4.Water Softener: - Iron exchange types with first fill of resin & come with ½ HP Single phase self priming Mono block pump. 5.Fuel Tank: - 100 litres capacity comes with valve, stand, piezometer, pipes & lid for closure. 6.Boiler Controller: - Control Panel with switches, gauges & meters. 7.Steam Turbine :- Rankin Blade, Impulse Turbine Qty.
8.Turbine Control Panel: - Comes with Digital Panel Meter 9.Surface Condenser: - Shell & Tube type with 2 nos. water & 1 no. Steam pass. 10.Cooling Water: - 2 HP Centrifugal Pump 3 phase is provided for the pungent 11.Vacuum Creation in Condenser: - 1 HP Reciprocating pump with 2880 rpm is provided to extract condensate from condenser and this create vacuum. 12.Control Valves: - To make Turbine Experiment either with or without condenser. 13.Steam Flow meter: - Steam Flow meter is provided with due calibration of Orifice condenser pots, valves, mercury manometer tubes etc. 14.Separating & Throttling Calorimeter: - Comes with calibrated Orifice Condenser pots, valves, mercury, Manometer tubes etc. 15.Steam Piping: - Complete conveying pipes, valves, flanges to connect boiler to various parameters. 16.Insulation for Steam lines: - Done with glass wool & Aluminium sheathed Cladding. 5 Mech 87 Variable speed air blower Test Rig 1.Study of Performance with 3 types Rotors. 2.Motors with VFD (variable frequency drive) to perform fan laws verification expts. 3.3 H.P. AC motor, 1500 rpm, 3 phases Kirloskar or standard make. 4.Digital speed indicator. 5.2 HP blower with AC motor 6.Digital air flow indicator. 7.3 different types of interchangeable rotors. 8.Pressure distribution in volute casing. 9.Provision for head and flow rate change. 10.Separate control panel for all instrumentation. 11.Rectangular M.S. duct of 2 m length. 6 Mech 88 Apparatus for calibration of turbine flow meter. a) The test rig consists of a GI pipeline fitted with a turbine flow meter (paddle wheel type) with digital flow readout. A strong iron stand is provided for supporting the pipe line and the rotameter. A stop watch and an M.S. collecting tank of size 90 liters. with a gauge glass scale fitting, a drain valve and a bend are provided to measure the actual 1 set
flow rate. c) A 220 volt AC, 0.5 HP, single phase monoblock ISI pumpset with suitable pipe fittings, strainer foot valve, and switch is provided to supply water to the test rig. d) A sump tank of size 200 liters with suitable drain is provided to store the water. A strong iron stand fitted with wheels supports the complete test rig. The unit is moveable. All tanks are lined with FRP for total rust protection. Apparatus for calibration of venturimeter, orificemeter and rotameter a) The test rig consists of GI pipe lines for fitting a set of gunmetal venturimeter and orificemeter of size 25mm(1"), and of d/d Ratio = 0.6. The pipe has the venturimeter and orificemeter provided with the pressure tappings with quick change over cocks, and a flow control valve. A differential manometer (without mercury) is provided to measure the pressure difference across the flow meter to be tested. The pressure tappings are connected to a common manifold which in turn is connected to the manometer. A strong iron stand is provided for supporting the pipe lines. A stop watch and an M.S. collecting tank of size 90 liters. with a gauge glass scale fitting, a drain valve and a bend are provided to measure the actual flow rate. b) A rotameter of range 5 to 55 lpm is connected with the other flow meters to indicate directly the flow rate. c) A 220 volt AC, 0.5 HP, single phase monoblock ISI pumpset with suitable pipe fittings, strainer foot valve, and switch is provided to supply water to the test rig. d) A sump tank of size 200 liters with suitable drain is provided to store the water. A strong iron stand fitted with wheels supports the complete test rig. The unit is moveable. All tanks are lined with FRP for total rust protection. 7 Mech 89 1. Pelton Wheel Turbine Test Rig (1 KW capacity 5HP supply pump) a) Test rig consists of a Pelton wheel water Turbine, designed for laboratory experimental purposes and to conduct test in metric units. The specifications of the turbine are as follows:- Design Speed - 1000 RPM. Output Power - 1.0 KW The turbine consists of a cast iron body with a large transparent acrylic window, a nozzle and spear arrangement, a rotor assembly of shaft, runner and a brake drum all mounted on a sturdy base frame. The Pelton buckets and nozzle are made of gunmetal and the spear made of brass for corrosion resistance. The input to the turbine is controlled by adjusting the spear position with a hand wheel. A rope brake arrangement with a spring 1 each
balance is provided for loading the turbine. The transparent perspex sheet side casing is provided for visual observation of flow on the buckets. Water inlet pressure is measured by a pressure gauge. b) Water to the turbine is provided by a centrifugal monoblock pump set of 5 HP capacity. The pump operates on 440Volts, 3 Phase, 50 Hz line. c) Other standard accessories include a DOL starter, switch, flow control gate valve, suitable piping. d) Flow measuring unit consists of a venturimeter with pressure taps connected to two pressure gauges mounted on a panel board. e) The complete test rig is mounted on a storage tank of suitable capacity. The tank is provided with FRP lining for total rust protection. 2. Francis Turbine Test Rig (1 KW capacity 5HP supply pump) a) Test rig consists of a Francis water turbine designed for laboratory experimental purpose and to conduct test in metric units. The specifications of the turbine are as follows:- Normal Speed - 2200 RPM. Capacity - 1.0 KW The unit consists of a cast iron casing, a rotor assembly of shaft, gunmetal runner and a brake drum all mounted on a suitable sturdy base. Guide vanes are provided in the turbine to regulate the flow into the runner. A conical draught tube is connected to the turbine outlet by a bend. A rope brake arrangement with a spring balance is provided for loading the turbine. Pressure gauge and vacuum gauge are fixed at the inlet and outlet to measure the net supply head to the turbine. b) Water to the turbine is provided by a centrifugal pump set of 5 HP capacity. The pump operates on 440Volts, 3 Phase, 50 Hz line. c) Other standard accessories include a DOL starter, switch, flow control valve, suitable piping. d) Flow measuring unit consists of a venturimeter with pressure taps connected to two pressure gauges mounted on a panel board. e) The complete test rig is mounted on a storage tank of 500 liters capacity. The tank is provided with FRP lining for total rust protection 3. Kaplan Turbine Test Rig (1 KW capacity 5HP supply pump) a) Test rig consists of a Kaplan turbine designed for laboratory experimental purposes and to conduct test in metric units. The specifications of the turbine are as follows: Normal Speed - 2200 RPM. Capacity - 1.0 KW The unit consists of a cast iron casing, a rotor assembly of shaft, an axial flow gunmetal runner and a brake drum all mounted on a suitable sturdy base. The runner has vanes of aerofoil section. Fixed guide vanes are provided in the turbine to regulate the flow into the runner. A conical draught tube is
connected to the turbine outlet by a bend. For observing the flow at the runner exit a transparent window made of thick perspex tube is provided in between the turbine casing and the draft bend. A rope brake arrangement with a set of dead weights and spring balance is provided for loading the turbine. Pressure gauge and vacuum gauge are fixed at the inlet and outlet to measure the net supply head to the turbine. b) Water to the turbine is provided by a centrifugal pump set of 5HP capacity. The pump operates on 440Volts, 3 Phase, 50 Hz line. c) Other standard accessories include a DOL starter, switch, flow control valve, suitable piping. d) Flow measuring unit consists of a venturimeter with pressure taps connected to two pressure gauges mounted on a panel board. e) The complete test rig is mounted on a storage tank of suitable capacity. The tank is provided with FRP lining for total rust protection 8 Mech 90 Cascade Refrigeration System High side Low side Refrigerant R 404A R-23 De-super-heater Required Compressor Hermetically sealed, Emerson Hermetically sealed, Emerson Compressor oil Standard Standard Condenser Air Cooled Cascade condenser tube type DrierDM-50 DM-50 Evaporator Tube-in-tube Forced convection air cooled Expansion device Thermostatic expansion valve Capillary Tube Accumulator Copper shell suction line accumulator provide Insulation 65 MM PUF 250 MM PUF Controls & Indications HP / LP Cut-out Provided Provided Temperature Digital Indicator with or Digital Indicator with or Pressure Pressure gauges 2 Nos. for suction and discharge Pressure gauges 2 Nos. for suction and discharge Electrical System Supply-230 Volts, 50 Hz, 1 phase Construction Outer body -Panel: 1.2 mm thick CRCA ; Powder coating Brine Tank-Stainless steel. Size-2165x800 x1675 mm (L*D*H) 9 Mech 91 Bench Center
Center to Center 23.6 in Workpiece Capacity 9.8 in Diameter Max. Weight 66 lbs Parallelism of Centers.00024 in Flatness of Surface.0008 in Attachment Diameter 3/8 in 967-202-10 10 Mech 92 Floating Carriage Micrometer College Model: Floating Carriage Diameter Measuring Machine along with Standard accessories : 1. Thread measuring prism - 1 no. 2. Cylinder setting master - 1 no. 3. Pair of Thread measuring wire 1 no. 4. Plain thread plug Gauge 1 no. 5. Two wire set 1 no 6. Setting master- 1 no Micrometer Head Range :25mm Repeatability:0.004 mm Resolution:0.0002 mm Accuracy:0.0mm Three Wire Unit A full set for 0.25-5.0 mm pitch threads