Alarms & Remote Start Automotive Data Solutions Inc. INSTALL GUIDE ADS-AL(TB)-MA-EN MA Available for : ADS-AL-CA Rev. Date: September 8, 0 The brand names and logos found in this guide are property of their respective owners. Automotive Data Solutions Inc. 0! NOTICE: The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. This guide has been written for properly trained technicians; a certain level of skill & knowledge is therefore assumed. Please review the Installation Guide carefully before beginning any work.
Page of 6 install type SeLeCtiOn data IMMoBILIZer Bypass InsTaLL Type year ModeL MaZda MaKe FeaTUres Miata STD key 0-0 MPV STD key 00-06 Automotive Data Solutions Inc. 0
Page 3 of 6 MPV STD key 00-06 WIre description ConneCTor name ConneCTor CoLor ConneCTor Type position WIre CoLor polarity ModULe LoCaTIon CoMponenT LoCaTor 0-0 MaZda Miata STD key year ModeL MaKe type - wire CrOSS reference CHart - OF V 8 Blue/Red Ignition Black/White Data Red/Black (DATA) Ground Black/Orange V 8 Blue/Red Ignition Black/White Data Blue/White or Blue/Black (DATA) Ground Black/Orange Automotive Data Solutions Inc. 0
Page of 6 type - wiring diagram IMMOBILIZER LOCATED NEAR STEERING COLUMN REMOTE STARTER TA DA 3 6 8 9 0 IG NI TI ON V (+) <- REQUIRED GROUND (-) <- REQUIRED GROUND WHEN RUNNING (-) OUTPUT <- REQUIRED DATA MODE LEGEND NOT REQUIRED IN DATA MODE (-WAY) NOT REQUIRED IN DATA MODE (-WAY) USE DATA MODE OR HARDWIRE MODE DATA MODE GWR (-) INPUT - BLUE/WHITE (NC) WHITE GROUND - BLACK V (+) - RED (NC) GREEN/BLACK (NC) BLUE/BLACK (NC) RED/WHITE (NC) BROWN (NC) PURPLE/YELLOW (NC) PURPLE/BLACK (NC) WHITE (NC) BLACK/WHITE (NC) GREEN (NC) PURPLE/WHITE WHITE/BLACK - DATA CONNECTOR SIDE WHITE/RED - DATA VEHICLE SIDE WHITE (NC) YELLOW/BLACK (NC) YELLOW/RED (NC) YELLOW (NC) BROWN/RED (NC) BROWN/YELLOW (NC) ORANGE/BLACK (NC) ORANGE/WHITE (NC) ORANGE (NC) PINK/BLACK - IGNITION OUTPUT CONNECTOR SIDE PINK - IGNITION INPUT VEHICLE SIDE BLUE/RED (NC) BLUE/YELLOW (NC) GREEN/RED (NC) GREEN/YELLOW (NC) GRAY/RED - DATA OUTPUT GRAY/YELLOW (NC) Automotive Data Solutions Inc. 0
Page of 6 installation mode SeLeCtiOn Press and release programming button to select installation mode. LED flashes (X) once = DATA MODE LED flashes (X) twice = STANDARD HARDWIRE MODE! Press and hold programming button until LED turns solid GREEN to register selection. After registration, follow Factory Reset Procedure to change installation mode and restart this procedure. module PrOgramming PrOCedUre Insert key into ignition. Turn key to START position. START 3 Wait, LED will turn solid GREEN for seconds. OFF Turn key to OFF position. (Engine running) Module Programming Procedure completed. Automotive Data Solutions Inc. 0
XX-XX CLASSIC PAGE X-X - Page 6 of 6 identify VeHiCLe year Locate the Vehicle Identification Number (VIN), identify the 0th character then match it to its corresponding year. Æ 3AYNTAL8DR0X Æ a 980 L 990 y 000 a 00 B 98 M 99 00 B 0 C 98 n 99 00 C 0 d 983 p 993 3 003 d 03 e 98 r 99 00 e 0 F 98 s 99 00 F 0 G 986 T 996 6 006 G 06 H 98 V 99 00 H 0 J 988 W 998 8 008 J 08 K 989 X 999 9 009 K 09 module diagnostics Led status diagnostics during programming during remote start WITH IGnITIon off Flashing RED Missing/wrong information from firmware or vehicle Incorrectly programmed Incorrectly programmed or connected Solid RED Waiting for more vehicle information Incorrectly programmed Not programmed waiting for more vehicle information Flashing GREEN Additional steps required to complete programming Correctly programmed and operational False ground when running status from remote starter Solid GREEN then OFF Correctly programmed Reset in progress Reset in progress OFF No activity or already programmed Invalid ground when running status from remote starter At rest and ready for a remote start sequence LED will turn solid red for seconds. RESET COMPLETED. 6 3 RECONNECT all connectors. DISCONNECT black -PIN standard or optional data connector. DISCONNECT all connectors from module EXCEPT the black -PIN standard or optional data connector. FaCtOry reset PrOCedUre PRESS AND HOLD programming button while connecting either -PIN standard or optional data connector. Repeat programming procedure.! Failure to follow procedure may result with a DTC or a CHECK ENGINE error message. When LED flashes red, RELEASE programming button. Automotive Data Solutions Inc. 0