Alarms & Remote Start Automotive Data Solutions Inc. INSTALL GUIDE OL-BLADE-TB-MA-EN Available for : OL-BLADE-TB Rev. Date: September 28, 205 Doc. No.: ##22960## MA The brand names and logos found in this guide are property of their respective owners. NOTICE: The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. This guide has been written for properly trained technicians; a certain level of skill & knowledge is therefore assumed. Please!review the Installation Guide carefully before beginning any work.
Page 2 of 6 OL-BLADE-TB-MA-EN Doc. No.: ##22960## 2050928 install type SeLeCtiOn FeaTUres MaZda MaKe ModeL year InsTaLL Type data IMMoBILIZer Bypass Miata STD key 0-04 MPV STD key 00-06
Page 3 of 6 OL-BLADE-TB-MA-EN Doc. No.: ##22960## 2050928 type - wire CrOSS reference CHart - OF MaZda MaKe ModeL year WIre description ConneCTor name ConneCTor CoLor ConneCTor Type position WIre CoLor polarity ModULe LoCaTIon CoMponenT LoCaTor Miata STD key MPV STD key 0-04 00-06 2V ~ ~ ~ 8 Blue/Red ~ At Immobilizer near Steering Column ~ Ignition ~ ~ ~ 7 Black/White ~ At Immobilizer near Steering Column ~ Data ~ ~ ~ 5 Red/Black (DATA) At Immobilizer near Steering Column ~ Ground ~ ~ ~ 4 Black/Orange ~ At Immobilizer near Steering Column ~ 2V ~ ~ ~ 8 Blue/Red ~ At Immobilizer near Steering Column ~ Ignition ~ ~ ~ 7 Black/White ~ At Immobilizer near Steering Column ~ Data ~ ~ ~ 5 Blue/White or Blue/Black (DATA) At Immobilizer near Steering Column ~ Ground ~ ~ ~ 4 Black/Orange ~ At Immobilizer near Steering Column ~
Page 4 of 6 OL-BLADE-TB-MA-EN Doc. No.: ##22960## 2050928 type - wiring diagram REMOTE STARTER IMMOBILIZER LOCATED NEAR STEERING COLUMN 6 2 7 8 9 3 4 5 0 2 DATA IGNITION ORANGE/BLACK *BLADE CONNECTOR EXACT PIN-OUT WHITE/RED WHITE PINK/BLACK NO WIRE BROWN/RED ORANGE BLUE/RED GREEN/RED GRAY/RED 0 20 09 9 08 8 07 7 06 6 05 5 04 4 03 3 02 2 0 WHITE/BLACK NO WIRE PINK BLACK BROWN/YELLOW ORANGE/WHITE NO WIRE BLUE/YELLOW YELLOW GRAY/YELLOW WHITE/BLACK - DATA CONNECTOR SIDE WHITE/RED - DATA VEHICLE SIDE WHITE (NC) YELLOW (NC) BROWN/RED (NC) BROWN/YELLOW (NC) ORANGE/BLACK (NC) ORANGE/WHITE (NC) ORANGE (NC) PINK/BLACK - IGNITION OUTPUT CONNECTOR SIDE PINK - IGNITION INPUT VEHICLE SIDE BLUE/RED (NC) BLUE/YELLOW (NC) GREEN/RED (NC) GRAY/RED - DATA OUTPUT GRAY/YELLOW (NC) BLACK (NC)
Page 5 of 6 OL-BLADE-TB-MA-EN Doc. No.: ##22960## 2050928 Cartridge installation Slide cartridge into unit. Notice button under LED. 2 Ready for Module Programming Procedure. module PrOgramming PrOCedUre Insert key into ignition. 3 Wait, LED will turn solid GREEN for 2 seconds. 2 START Turn key to START position. (Engine running) 4 OFF Turn key to OFF position. 5 Module Programming Procedure completed.
Page 6 of 6 OL-BLADE-TB-MA-EN Doc. No.: ##22960## 2050928 identify VeHiCLe year Locate the Vehicle Identification Number (VIN), identify the 0th character then match it to its corresponding year. Æ 4 3 A 5 Y N 5 T A L 8 D 5 R 0 X Æ a 980 L 990 y 2000 a 200 B 98 M 99 200 B 20 C 982 n 992 2 2002 C 202 d 983 p 993 3 2003 d 203 e 984 r 994 4 2004 e 204 F 985 s 995 5 2005 F 205 G 986 T 996 6 2006 G 206 H 987 V 997 7 2007 H 207 J 988 W 998 8 2008 J 208 K 989 X 999 9 2009 K 209 Led status Flashing RED diagnostics during programming during remote start WITH IGnITIon off Missing/wrong information from firmware or vehicle Incorrectly programmed Solid RED Waiting for more vehicle information Incorrectly programmed Flashing GREEN Additional steps required to complete programming module diagnostics Correctly programmed and operational Incorrectly programmed or connected Not programmed waiting for more vehicle information False ground when running status from remote starter Solid GREEN then OFF Correctly programmed Reset in progress Reset in progress OFF No activity or already programmed Invalid ground when running status from remote starter At rest and ready for a remote start sequence FaCtOry reset PrOCedUre DISCONNECT cartridge from remote starter. 3 LED will flash red. Immediately RELEASE programming button. 2 PRESS AND HOLD programming button while re-connecting cartridge to remote starter. 4 LED will turn solid red for 2 seconds. RESET COMPLETED. 5 RECONNECT all connectors. Repeat programming procedure.! Failure to follow procedure may result with a DTC or a CHECK ENGINE error message.