SALFORD TILLAGE SPECIALISTS Подбор запасных частей на сайте: http://texagropark.ru 870 DISC 2007 32' & 35 MODELS 9" C-FLEX ASSEMBLY AND PARTS MANUAL Лесных Павел Владимирович Тел. 903-030-15-51 E-mail: lpv310180@mail.ru lpv@texagropark36.ru ООО «ТехАгроПарк» 396336 Воронежская обл., Новоусманский р- н, п. Отрадное, ул. Автодорожная 7. (трасса М4 «Дон» 519 км пост ГАИ) Тел./факс 8 (473) 233-28-17 E-mail: info@texagropark36.ru
TABLE OF CONTENTS Recommended Torque Values..1 Frame assembly Mainframe Installation 2 Mainframe W-Tower Installation 3 Wing Installation.4 Tongue Installation.6 Self Leveling PVT Installation and Depth Control Rod.8 Lights and SMV Installation..10 Wheel and axle assembly 10,000 lb Main & Wing Disc Axle Assembly...12 16,000 lb Tandem Axle (2 DOM).14 Mainframe Axle Installation..16 Wing Axle Mount Installation..18 Wing Axle Installation..20 Hydraulics Lift Hydraulics... 22 Wing Hydraulics...23 Disc Gangs Front Mainframe Assembly 24 C-Flex Hanger Assembly 26 2 ¼ Disc Gang Bearing Assembly 28 Wide Mainframe 9 Spacing 2 ¼ Shaft Layout..30 Disc Step Down Layout...31 Harrows 62 Long Harrow Arm Assembly 32 ½ Tine Harrow Assemblies 34 14 Roller Harrow Assemblies...36 Wing Mounted Harrow Installation 38 Mainframe Mounted Harrow Installation..39 Harrow Layout.40 Optional Equipment Tow Hitch Assembly 41 Подбор запасных частей на сайте: http://texagropark.ru
SALFORD RECOMMENDED TORQUE VALUES BOLT SIZE GRADE 2 GRADE 5 GRADE 8 ft-lbs Nm ft-lbs Nm ft-lbs Nm 1/2"NC 50 68 75 102 105 142 5/8"NC 90 122 150 203 210 285 3/4"NC 160 217 270 366 375 508 7/8"NC 145 197 395 536 610 827 1"NC 210 285 590 800 910 1234 NOTES: These recommended torque values are applicable when applied to the nut only. These recommended torque values are approximate only. The torque-tension relationship is affected by lubrication, surface finish, thread fit, plating, lock-washers, etc. DO NOT use these values if a different torque value or tightening procedure is given for a specific application. Torque values listed are for general use only. Check tightness of fasteners periodically. Shear bolts are designed to fail under predetermined loads. Always replace shear bolts with identical grade. Fasteners should be replaced with the same or higher grade. If higher-grade fasteners are used, these should only be tightened to the strength of the original. Make sure fasteners threads are clean and that you properly start thread engagement. This will prevent them from failing when tightening. WARNING Do not tighten one side of the u-bolt before the other side. Both sides of the u-bolt must be tightened equally. 12-2007 Salford Farm Machinery Ltd. Page 1
3 4 ITEM NO. QTY. PART NO. DESCRIPTION 1 1 D70001A 870 DISC MAINFRAME - HEAVY AXLE INSTALLATION LH 2 1 D70001B 870 DISC MAINFRAME - HEAVY AXLE INSTALLATION RH 3 27 BN10S 5/8" NC STOVER LOCK NUT 4 54 BF10HS 5/8" HARD STRUCTURAL FLAT WASHER 5 27 B1025 5/8 x 2 1/2" HEX BOLT GR 5 4 5 DO NOT INSERT TOP BOLTS AT THIS TIME 2 1 2007 870 35' Disc Assembly and Parts Manual MAINFRAME INSTALLATION Page 2 Salford Farm Machinery Ltd. 12-2007
MAINFRAME W-TOWER INSTALLATION - 870 35' DISC IMPORTANT 16 15 WHEN FOLDING FOR THE FIRST TIME BOLT MUST BE ALL THE WAY IN, AFTER; SET BOLT SO CYLINDER WILL NOT BE UNDER PRESSURE IN TRANSPORT POSITION THEN TIGHTEN JAM NUT. ITEM NO. QTY. PART NO. DESCRIPTION 4 30 BN10S 5/8" NC STOVER LOCK NUT 5 60 BF10HS 5/8" HARD STRUCTURAL FLAT WASHER 6 1 D10048 870 FRONT WIDE W-TOWER W/WING REST 7 1 D70106 REAR W-TOWER 8 1 D10049 W-TOWER TO SPIDER BRACE 9 1 GP1600512A05 PIN 1" DIA. x 5 1/2" LG. - 2 HOLES 10 2 BF16 1" FLAT WASHER 11 2 BSC0415 1/4" x 1 1/2" COTTER PIN 12 1 D70112 SELF-LEVELING CYLINDER MOUNT 7 13 4 BU1046 U-BOLT 5/8" x 4" x 7 1/2" LG. 14 14 16 BN10L 5/8" NYLOCK NUT NC 15 4 BN16J 1"NC JAM NUT 16 4 B1630 1" NC x 3" HEX BOLT GR.5 PLATED 17 3 B1035 5/8 x 3 1/2" HEX BOLT 18 8 B1080 5/8 x 8" HEX BOLT GR. 5 PLATED 19 2 D10016 DISC WRENCH 8 9 13 11 10 6 Подбор запасных частей на сайте: http://texagropark.ru 5 17 5 19 18 4 18 14 12 12-2007 Salford Farm Machinery Ltd. Page 3
WING INSTALLATION 6 5 3 LH 35' WING INSTALLATION 7 FRONT 4 8 2 3 14 NOTE: WINGLOCKS MUST BE TOWARD THE INSIDE AND TO THE FRONT OF MACHINE. RH 35' WING INSTALLATION 1 5 6 6 4 1 3 2 8 7 8 15 Page 4 Salford Farm Machinery Ltd. 12-2007
870 35' WING INSTALLATION ITEM NO. QTY. PART NO. DESCRIPTION 1 9 BN08L 1/2" NYLOCK NUT NC 2 9 B0830 1/2" x 3" HEX BOLT 3 4 GP2401012A09 1 1/2" DIA. x 10 1/2" LG. 4 3 2 B1070 5/8 x 7" HEX BOLT GR 5 5 32 BN10L 5/8" NYLOCK NUT NC 6 64 BF10HS 5/8" HARD STRUCTURAL FLAT WASHER 7 8 L 0 0 4 1 7 1 X 4 X 8" PULL-UP PLATE 8 4 D70015 870 WING HINGE 14 1 870 64in. WIDE WING LEFT 870-35' LH WING WELDMENT 15 1 870 64in. WIDE WING RIGHT 870-35' RH WING WELDMENT 1. Install wing hinges (8) by aligning holes with holes on the mainframe, insert 1 1/2" x 10 1/2" pin (3) and retain with 1/2" x 3" hex bolt (2) and 1/2" nylock nut (1), once all pins and bolts are installed on hinges to mainframe, lift up wing hinges by setting a block underneath to make hinges parallel to mainframe. 2. Place wings at hinges making sure that the right hinges are on the right side and the left on the left, insert 5/8" x 7" hex bolts (4) with 5/8" hard structural flat washer (6) into pull-up plates (7) and align with holes on wing hinges and retain with 5/8" nylock nuts (5) and hard structural flat washers (6), NOTE: BEFORE TIGHTENING BOLTS ENSURE WINGS ARE PARALLEL WITH MAINFRAME AND FRONT OF WING LINES UP WITH FRONT OF MAINFRAME. Подбор запасных частей на сайте: http://texagropark.ru 12-2007 Salford Farm Machinery Ltd. Page 5
TONGUE INSTALLATION 14 2 19 5 12 8 9 6 12 11 13 15 10 4 17 3 20 18 16 7 1 20 23 25 19 24 22 21 Подбор запасных частей на сайте: http://texagropark.ru Page 6 Salford Farm Machinery Ltd. 12-2007
TONGUE INSTALLATION ITEM NO. QTY. PART NO. DESCRIPTION 1 1 P9701C 860-870-9700 CAST CLEVIS TONGUE 2 1 A60041 570-580-860-870-9700 INNER TELESCOPE 3 1 A60040 OUTER TELESCOPE 48" 4 1 A50010 TURNBUCKLE 5 1 C1014 6 TIP HOSE HOLDER 6 1 PPI-42XL CAT 4 CAST IRON HITCH 7 1 GJ8002 8000 LB TONGUE JACK 8 1 GJ652027 20,000 LB SAFETY CHAIN 9 2 B1680H 1" x 8" NC HEX BOLT GR. 8 10 2 BN16L 1-8 NC NYLOCK NUT 11 1 GP1600512A05 PIN 1" DIA. x 5 1/2" LG. - 2 HOLES 12 2 BF16S 1" SAE WASHER 13 2 BSC0515 5/16" x 1 1/2" COTTER PIN 14 2 GP1600258H04 PIN 1" DIA. x 2 5/8" LG. WITH HEAD 15 4 BSC0415 1/4" x 1 1/2" COTTER PIN 16 1 GP10004L03 L-PIN 5/8" DIA. x 4" LG. 17 1 GHP11 #11 HAIR PIN 18 1 BU0830 1/2" x 3" x 4 1/2" U-BOLT 19 8 BN08L 1/2" NYLOCK NUT NC 20 1 GF641 1/4"-28NF GREASE FITTING 21 1 BN05L 5/16" LOCK NUT 22 4 B0830 1/2"NC x 3" HEX BOLT 23 1 B0520 5/16"NC x 2" BOLT 24 2 GP2400758A09 PIN 1 1/2" DIA. x 7 5/8" LG. - 2 HOLES 25 1 GP1600614B05 PIN 1" DIA. x 6 1/4" LG - 1 HOLE 1. Attach tongue (1) to frame assembly using 1 1/2" x 7 5/8" pins (24). Retain pins with 1/2" x 3" hex bolts (23) and 1/2" locknuts (8). 2. Insert inner telescope (2) into outer telescope (3). Attach turnbuckle (4) to telescope with 1" x 2 5/8" head pins (14) and 1/4" x 1 1/2" cotter pins (15). Install grease fitting (20) in end of outer telescope. 3. Attach top of telescope assembly to self-levelling assembly with 1" x 6 1/4" pin (25). Retain pin with 5/16" x 2" hex bolt (23) and 5/16" locknut (21). 4. Attach bottom of telescope assembly and safety chain (8) to tongue with 1" x 7 5/8" pin (24), 1" SAE washers (12), and 5/16" x 1 1/2" cotter pins (13). Note: pin goes through chain link in centre of tube. Washers go between plate and cotter pin. 5. Install hitch clevis (6) in end of tongue with 1" x 8" Grade 8 hex bolts (9) and 1" lock nuts (10). Insert bolts from opposite sides as shown. Add 1" washers between hitch and mounting plates if any play or clearance exists. 6. Install jack (7) onto tongue with 5/8" x 4" L-pin (16) and #11 hairpin (17). 7. Install hose holder (5) onto telescope approximately 16" from the end of the telescope. Retain hose holder with 1/2" x 3" x 4 1/2" u-bolt (18) and 1/2" locknuts (19). 12-2007 Salford Farm Machinery Ltd. Page 7
SELF LEVELLING PIVOT INSTALLATION ITEM NO. QTY. PART NO. DESCRIPTION 1 1 D70111 SELF-LEVELING PIVOT 2 2 HSR4012 4" BORE x 12" STROKE HYD. CYLINDER 3 2 GP1600314H04 PIN 1" DIA. x 3 1/4" LG. WITH HEAD 4 1 GP2401514A09 PIN 1 1/2" DIA. x 15 1/4" LG. - 2 HOLES 5 1 GP2001058A05 1 1/4" DIA. x 10 1/4" LG - 2 HOLE 6 2 BN08L 1/2" NYLOCK NUT NC 7 2 B0830 1/2" x 3" HEX BOLT 8 2 GM30 1 1/4" MACHINE BUSHING 9 4 BSC0415 1/4" x 1 1/2" COTTER PIN 10 2 BSC0520 5/16" x 2" COTTER PIN 10 5 7 4 9 8 1 6 2 3 Подбор запасных частей на сайте: http://texagropark.ru Page 8 Salford Farm Machinery Ltd. 12-2007
DEPTH CONTROL ROD INSTALLATION ITEM NO. QTY. PART NO. DESCRIPTION 25 1 C1008 DETENT ADJUSTABLE STOP 26 1 C1003-30 30" DEPTH CONTROL ROD W/WELDED RING 27 1 D10011A POPPET VALVE BRACKET 28 1 BU1046 U-BOLT 5/8" x 4" x 7 1/2" LG. 29 1 HPMSC10 STROKE CONTROL VALVE 30 2 B0525 5/16"NC x 2 1/2" HEX BOLT 31 2 BN05L 5/16" LOCK NUT 26 25 29 28 27 24 27 30 31 Boss must face mounting bracket 12-2007 Salford Farm Machinery Ltd. Page 9
13 12 11 4 15 10 8 14 6 6 3 4 7 9 3 5 2007 870 35' Disc Assembly and Parts Manual LIGHTS AND SMV INSTALLATION Page 10 Salford Farm Machinery Ltd. 12-2007
870 LIGHTS AND SMV INSTALLATION ITEM NO. QTY. PART NO. DESCRIPTION 3 3 BU1061 U-BOLT 5/8" x 6" x 5 1/2" 4 6 BN10L 5/8" NYLOCK NUT NC 5 8 B0410 1/4" NC x 1 1/2" HEX BOLT 6 16 BN04L 1/4" LOCK NUT 7 1 C1011 SMV MOUNTING BRACKET 8 1 GAP103NS SMV SIGN 9 2 BN06L 3/8"-16NC LOCK NUT 10 2 B0610 3/8 X 1" PLATED BOLT GR.5 11 2 A60055 LIGHT BRACKET (SHORT) 12 2 L00425 OUTSIDE LIGHT MOUNTING PLATE 13 2 GL767762-AA ORANGE LIGHT 14 2 GL767762-R RED LIGHT 15 4 BU0415 1/4 x 1 1/2" U-BOLT Подбор запасных частей на сайте: http://texagropark.ru 12-2007 Salford Farm Machinery Ltd. Page 11
10000 LB WING DISC AXLE ASSEMBLY ITEM NO. QTY. PART NO. DESCRIPTION 1 1 C00083L 10000 LB UPRIGHT BEAM - LH 2 1 C00083R 10000 LB UPRIGHT BEAM - RH 3 1 C00084L 10000 LB DISC AXLE WALKING BEAM WLDMNT - LH 4 1 C00084R 10000 LB DISC AXLE WALKING BEAM WLDMNT - RH 5 2 GB28995 12000 LB CONE, 10000 LB INNER CONE 6 2 GB28921 12000 LB CUP, 10000 LB INNER CUP 7 2 GB255204 10000 LB OUTER CUP 8 2 GB255814 10000 LB OUTER CONE 9 2 BF20HS 1 1/4" HARD STRUCTURAL WASHER 10 2 BN20SF 1 1/4"NF SLOTTED HEX NUT 11 2 BSC0425 1/4" x 2 1/2" COTTER PIN 12 2 GW9112 10,000 LB DUST CAP 13 3 GW8000A 8000 lb GREASABLE HUB AND 14" SPINDLE ASSY 14 3 B1045 5/8 x 4-1/2" BOLT 15 3 BN10L 5/8" NYLOCK NUT NC 16 2 GF1610 1/8" NPT GREASE FITTING 17 4 GBB175150200 1 3/4" x 1 1/2" x 2" LG. HARD BUSHING 18 2 GW12110VC 10000/12000 LB COUNTERFACE 19 2 GW12110VS 10000/12000 LB V-SEAL 20 2 GW12110VW 10000/12000 LB GRASS WRAP GUARD FRONT LH AXLE ASSEMBLY RH AXLE ASSEMBLY Page 12 Salford Farm Machinery Ltd. 12-2007
5 6 13 10000 LB WING DISC AXLE ASSEMBLY LH RH 1 2 17 15 LH RH 3 4 20 19 18 14 7 8 9 10 LEFT HAND ASSEMBLY SHOWN 16 11 12 12-2007 Salford Farm Machinery Ltd. Page 13
16000 LB TANDEM AXLE ASSEMBLY (2" DOM) ITEM NO. QTY. PART NO. DESCRIPTION 1 1 C00089L 16000 LB 870 DISC MAIN AXLE UPRIGHT LH 2 1 C00089R 16000 LB 870 DISC MAIN AXLE UPRIGHT RH 3 1 C00090L 16000 LB 870 DISC MAIN AXLE WALKER LH 4 1 C00090R 16000 LB 870 DISC MAIN AXLE WALKER RH 5 1 GB47687 16000 LB INNER CUP 6 1 GB39585 16000 LB OUTER CUP 7 1 GW16112 16000 LB DUST CAP 8 1 GW16110 16000 LB GREASE SEAL 9 1 GB47620 16000 LB INNER CONE 10 1 GB39520 16000 LB OUTER CONE 11 1 BN28SF 1 3/4" NF SLOTTED FLANGE NUT 12 1 BSR0527 5/16" x 2 3/4" ROLL PIN 13 4 B0505 5/16"NC x 1/2" LG. HEX BOLT 14 2 GW12000A15 12000 LB HUB AND 15" SPINDLE ASSEMBLY 15 2 B1055H 5/8 x 5 1/2" HEX BOLT GR 8 16 2 BN10L 5/8" NYLOCK NUT NC 17 3 GF1610 1/8" NPT GREASE FITTING FRONT 16" CENTRES LH AXLE ASSEMBLY RH AXLE ASSEMBLY Page 14 Salford Farm Machinery Ltd. 12-2007
9 5 17 16000 LB TANDEM AXLE ASSEMBLY (2" DOM) LH RH LH RH 1 2 14 16 3 4 8 9 5 15 6 10 6 10 11 12 7 13 LEFT HAND ASSEMLY SHOWN 12-2007 Salford Farm Machinery Ltd. Page 15
870 MAINFRAME AXLE INSTALLATION 16 14 13 18 1 17 15 5 3 4 9 2 11 6 7 8 7 12 10 LEFT HAND AXLE SHOWN USE SAME METHOD FOR RIGHT HAND AXLE Подбор зарасных частей на сайте: http://texagropark.ru Page 16 Salford Farm Machinery Ltd. 12-2007
870 MAINFRAME AXLE INSTALLATION ITEM NO. QTY. PART NO. DESCRIPTION 1 1 D70001A 870 DISC MAINFRAME - HEAVY AXLE INSTALLATION LH 2 1 C50010 TRANSPORT LOCK ASSEMBLY 3 2 BF16 1" FLAT WASHER 4 2 BSC0415 1/4" x 1 1/2" COTTER PIN 5 1 GP16005A05 PIN 1" DIA. x 5" LG. - 2 HOLES 6 1 GP1600212H04 PIN 1" DIA. x 2 1/2" LG. WITH HEAD 7 2 BSC0315 3/16" x 1 1/2" COTTER PIN 8 1 C00091L 16000 LB 870 DISC MAIN AXLE ASSEMBLY LH 9 1 GP200190000B11 2" x 19" LG 1-HOLE PIN 10 2 GW12158 12.5L x 15FL x 8 BOLT WHEEL & TIRE (12 PLY HIGHWAY) 11 1 HSR4508H 4 1/2" BORE x 8" STROK HYD. CYLINDER 12 1 GP1600312H04 PIN 1" DIA. x 3 1/2" LG. WITH HEAD 13 1 B1040 5/8 x 4" HEX BOLT GR 5 14 1 BN10 5/8" NC HEX NUT GR.5 15 1 B0815 1/2" x 1 1/2" HEX BOLT 16 1 GPH2000734F 1 1/4" x 7 3/4" LG. AXLE PIN - HARDENED 17 1 BL08 1/2" SPRING WASHER 18 2 GBB150125100 1 1/2" x 1 1/4" x 1" LG. HARD BUSHING 12-2007 Salford Farm Machinery Ltd. Page 17
870 WING AXLE MOUNT INSTALLATION 18 20 19 16 19 20 21 15 16 11 4 4 LH WING AXLE MOUNT INSTALLATION 12 16 4 21 20 14 19 17 20 19 4 RH WING AXLE MOUNT INSTALLATION Page 18 Salford Farm Machinery Ltd. 12-2007
870 AXLE MOUNT INSTALLATION ITEM NO. QTY. PART NO. DESCRIPTION 4 20 BN10L 5/8" NYLOCK NUT NC 11 1 870 64in. WIDE WING LEFT 870 NARROW WING FRAME LEFT 12 1 870 64in. WIDE WING RIGHT 870 NARROW WING FRAME RIGHT 14 1 D70032 WIDE AXLE HANGER, WING RH 15 1 D70005 WIDE AXLE HANGER FOR WING LH 16 10 BU1046 U-BOLT 5/8" x 4" x 7 1/2" LG. 17 1 D10019R RH WING AXLE ADJUSTER 18 1 D10019L LH WING AXLE ADJUSTER 19 4 BF20 1 1/4" FLAT WASHER 20 4 BN24 1 1/4" HEX NUT PLATED 21 2 BN20J 1 1/4" HEX JAM NUT GR.5 PLATED 12-2007 Salford Farm Machinery Ltd. Page 19
870 WING AXLE INSTALLATION 9 10 7 8 11 8 11 LEFT HAND AXLE SHOWN USE SAME METHOD FOR RIGHT HAND AXLE Page 20 Salford Farm Machinery Ltd. 12-2007
870 WING AXLE INSTALLATION ITEM NO. QTY. PART NO. DESCRIPTION 7 1 GP2401212B09 1 1/2" X 12 1/2" LG. 1 HOLE PIN 8 2 GP1600312H04 PIN 1" DIA. x 3 1/2" LG. WITH HEAD 9 1 B0830 1/2" x 3" HEX BOLT 10 1 BN08 1/2" HEX NUT NC 11 2 BSC0415 1/4" x 1 1/2" COTTER PIN 12-2007 Salford Farm Machinery Ltd. Page 21
LIFT AXLE HYDRAULICS Page 22 Salford Farm Machinery Ltd. 12-2007
12-2007 Salford Farm Machinery Ltd. Page 23
9" SPACING DISC GANG DISC GANG ASSEMBLY LEFT FRONT MAINFRAME SHOWN 15 18 19 19 12 15 17 11 14 20 16 13 3 1x 1 1/2" SPACER (8) USED FOR 9" SPACING 6 9 LEFT HAND ASSEMBLY SHOWN 7 8 5 1 6 2 5 4 10 DISC WRENCH HAVE SOMEONE USE A DISC WRENCH ON 1 OF THE SQUARE NUTS (4), WHILE YOU TIGHTEN THE OTHER SQUARE NUT (4), THIS WILL ALLOW YOU TO TIGHTEN EACH NUT EASIER. 4 2007 870 35' Disc Assembly and Parts Manual Page 24 Salford Farm Machinery Ltd. 12-2007
DISC GANG ASSEMBLY - LEFT FRONT MAINFRAME 9" SPACING ITEM NO. QTY. PART NO. DESCRIPTION 1 1 DK36098 2 1/4" DIA. DISC SHAFT 98 1/2" LG 2 8 D20020 SPOOL 9" x 6" DIA 3 11 CT50322 24" SMOOTH C.B. 6.5 MM (2.25" ROUND) 675 RAD. 4 2 D20024 2 1/4" SLOTTED SQUARE NUT 5 4 D20011-00 6" x 1 1/2" CONVEX WASHER 6 4 D20012-01 6" x 1 1/2" CONCAVE WASHER 7 3 D10040A 2 1/4" TRUNNION BEARING CARTRIDGE ASSEMBLY 8 3 D20021 3 1/2" x 1 1/2" FLAT SPACER 9 3 D00023B C-FLEX HANGER W/ BEARING RH 10 1 U40604090 TUBE 4" x 6" x 1/4"W x 90" LG. 11 1 U20203096 TUBE 2" x 2" x 3/16"W x 96" LG. 12 3 D10042 C-FLEX SCRAPER HANGER 13 11 D10018 SCRAPER BLADE (RIGHT AND LEFT) 14 22 BN08L 1/2" NYLOCK NUT NC 15 12 BN10L 5/8" NYLOCK NUT NC 16 11 BU0820 1/2" x 2 x 3 U-BOLT 17 3 BU1020 5/8" x 2 x 3 1/2" U-BOLT 18 3 BU1061 U-BOLT 5/8" x 6" x 5 1/2" 19 12 BF10HS 5/8" HARD STRUCTURAL FLAT WASHER 20 22 BF08HS 1/2" HARD STRUCTURAL FLAT WASHER 12-2007 Salford Farm Machinery Ltd. Page 25
C-FLEX HANGER ASSEMBLY 12 4 3 8 6 7 2 6 7 5 1 16 14 15 11 13 Tighten this bolt to approx. 600 ft/lbs Use thread locker Then install Bolt locking plate (13) For 1 1/2" disc shafts 10 9 For 2 1/4" disc shafts Page 26 Salford Farm Machinery Ltd. 12-2007
C-FLEX HANGER ASSEMBLY ITEM NO. QTY. PART NO. DESCRIPTION 1 1 D10026 2 1 /4" C-FLEX BEARING HANGER 2 1 D10023 1 1/4" C-FLEX SPRING 3 1 L00676 1" x 5" x 9" PLATE 4 2 B1285 3/4" NC X 8" HEX BOLT GR.5 PLATED 5 2 B1230 3/4" x 2" HEX BOLT GR.5 PLATED 6 5 BF12HS 3/4" HARD STRUCTURAL WASHER 7 5 BN12S 3/4" STOVER LOCK NUT 8 1 D10034 2 1/4" C-FLEX PULL-UP PLATE WITH STOPPER 9 1 D10040A 2 1/4" TRUNNION BEARING CARTRIDGE ASSEMBLY 10 1 D10055 1 1/2" DISC TRUNNION BEARING ASSEMBLY 11 2 GBB150125100 1 1/2" x 1 1/4" x 1" LG. HARD BUSHING 12 1 B1275 3/4 x 9" HEX BOLT 13 2 D10054 GANG HANGER PIVOT BOLT 14 2 FL00156 BOLT LOCKING PLATE 15 2 B0825 1/2" x 2 1/2" HEX BOLT 16 2 BN08L 1/2" NYLOCK NUT NC RH hanger assembly LH hanger assembly The same parts can be assembled for LH or RH hangers. 12-2007 Salford Farm Machinery Ltd. Page 27
2 7 2 1/4" DISC GANG C-FLEX HANGER BEARING ASSEMBLY 5 2 7 6 1 3 4 6 5 2007 870 35' Disc Assembly and Parts Manual Page 28 Salford Farm Machinery Ltd. 12-2007
2 1/4" DISC GANG C-FLEX HANGER BEARING ASSEMBLY ITEM NO. QTY. PART NO. DESCRIPTION 1 1 D10027 BEARING HOUSING WITH STUBS WELDED 2 2 GB6213 2 1/4" DISC BEARING 3 1 D00039 CENTRE SPACER 4 1 D00036 2 1/4 BEARING CENTRE SLEEVE 5 2 D00037 2 1/2" BEARING SLEEVE END CAPS 6 2 GBS39961 2 1/4" DISC BEARING RUBBER SEAL 7 2 GBS39961U 2 1/4" DISC BEARING URETHANE WIPER 12-2007 Salford Farm Machinery Ltd. Page 29
DISC GANG LAYOUT 870-35' WIDE MAINFRAME 9" SPACING 2 1/4" SHAFT SHAFT 116 1/2" SHAFT 98 1/2" SHAFT 98 1/2" 109" GANG TUBE 90" GANG TUBE 90" GANG TUBE 115" SCRAPER TUBE 10 1/2" 96" SCRAPER TUBE 96" SCRAPER TUBE 126" GANG TUBE 10 1/2" 84" GANG TUBE 84" GANG TUBE 10 1/2" 80" SCRAPER TUBE 80" SCRAPER TUBE 132" SCRAPER TUBE SHAFT 134 1/2" SHAFT 80 1/2" SHAFT 80 1/2" 94 BLADES + 2 FURROW FILLERS 10 1/2" SHAFT 116 1/2" 109" GANG TUBE 115" SCRAPER TUBE 126" GANG TUBE 132" SCRAPER TUBE SHAFT 134 1/2" Page 30 Salford Farm Machinery Ltd. 12-2007
2 1 4 DISC STEP DOWN LAYOUT 9" SPACING 4 1 3 2 1 4 4 1 35' DISC LAYOUT SHOWN ITEM # DISC SIZE/PART # & BEARING # # OF PARTS PER SIZE OF UNIT @ 9" SPACING 21' 6" 24' 8" 26' 29' 31' 8" 35' 1 24 - CT50322 54 62 66 74 82 90 2 22 - CT502662 4 4 4 4 4 4 3 18 - CT501862 2 2 2 2 2 2 4 D10045 BEARING CARTRIDGE 16 16 16 18 20 22 2 2 3 12-2007 Salford Farm Machinery Ltd. Page 31
62 INCH LONG HARROW ARM ASSEMBLY (5/8" PIVOT BOLT) 20 23 12 21 18 19 22 24 4 5 16 14 7 6 9 25 9 1 13 27 On flat-fold wing-mounted arm assemblies only 17 Only use here when (13) is not required. 17 3 6 FLIP SPACER OVER TO LOWER TRANSPORT HEIGHT 11 10 2 7 STANDARD POSITION AS SHOWN. NOTE: ON SOME MODELS (26) IS USED 26 OFFSET BLOCK TO ADJUST TRANSPORT HEIGHT Note: Tines shown with pin in bottom hole. 8 2007 870 35' Disc Assembly and Parts Manual Page 32 Salford Farm Machinery Ltd. 12-2007
62 INCH LONG HARROW ARM ASSEMBLY (5/8" PIVOT BOLT) + + + + + + + + + + + ITEM NO. QTY. PART NO. DESCRIPTION 1 1 R30012 PARALLEL LINKAGE BAR 2 1 R30006 PARALLEL LINKAGE ARM 3 1 R80099 HEAD,SALFORD HARROW FOR 5/8" UPPER PIVOT BOLT 4 1 R80100 62" HARROW ARM FOR 5/8" PIVOT AND U-BOLTS 5 1 R80100A 62" HARROW ARM W/ KIT (REPLACES RB1125) 6 5 BC0835H 1/2" X 13NC X 3-1/2" LG. CARRIAGE BOLT GR. 5 7 4 R0030 NYLON BUSHING 3/4" OD x 1/2" ID x 1.94 LG. 8 5 BN08L 1/2" NYLOCK NUT NC 9 6 BN10L 5/8" NYLOCK NUT NC 10 1 GP0800312L03 1/2" x 3 1/2" PARKING STAND PIN 11 1 GHP11 #11 HAIR PIN 12 2 R0035 2" x 10" HARROW ARM SPRING 13 1 R80032 FLAT-FOLD ROLLER ARM STOP BRACKET 14 1 R80037L TINE SECTION UPRIGHT PLATE LEFT 15 1 R80037R TINE SECTION UPRIGHT PLATE RIGHT 16 1 R0028 STEEL HEAD SPACER 2 1/8" LG. 17 2 B1037ST 5/8" - 11NC X 3 3/4" SHORT THREAD BOLT 18 1 R80098 7/8"OD NYLATRON BUSHING 19 1 R80106 7/8"OD - 0.520"ID NYLATRON ROD 20 1 R80096 HARROW ARM SPACER 21 2 RB0021 TIGHTENER,SINGLE SPRING 22 2 B0615 3/8" X 1 1/2" LG. GRADE 5 23 2 BN06L 3/8"-16NC LOCK NUT 24 2 GHP9 #9 HAIR PIN 25 2 BU1020 5/8" x 2 x 3 1/2" U-BOLT 26 1 R80035 SPACER BLOCK 27 1 B1045 5/8 x 4 1/2" HEX BOLT GR 5 NOTES: + PLEASE NOTE- R80100 (62" HARROW ARM) IS ALSO AVAILABLE AS R80100A (THIS PART# INCLUDES (19) FOR 1/2" & (18) FOR 5/8" PIVOT BOLT AS WELL AS NEW 5/8" U-BOLTS) AND REPLACES PART# RB1125 (FOR 1/2" NYLON BUSHING AND U-BOLTS). + + SOME MODELS MAY USE (26) INSTEAD OF (20) + + + ONLY USE (27) IF (13) IS NEEDED FOR DOUBLE FOLDED WINGS 12-2007 Salford Farm Machinery Ltd. Page 33
FOR ENDS OF FRONT TUBE ONLY 16 18 14 17 3 6 8 2 OPTIONAL SECOND TUBE FOR WEIGHT 7 5 6 20 4 13 21 12 9 11 10 TINE ANGLE ADJUSTER SHOWN HERE ON INNER LEFT. SEE HARROW LAYOUT FOR MACHINE SPECIFIC POSITIONS. 15 16 14 FOR ADJUSTOR MOUNTS ONLY 14 19 ALL OTHER POSITIONS 16 1 2007 870 35' Disc Assembly and Parts Manual Page 34 Salford Farm Machinery Ltd. 12-2007
1/2" - 3 TINE HARROW ASSEMBLY PART NO. R633 ITEM NO. PART NO. DESCRIPTION 1 U252503054 TUBE 2 1/2 x 2 1/2 x 3/16"W x 54" LG. 2 R6063 TINE PIPE FOR 1/2" (3-TINE) 1/2" - 4 TINE HARROW ASSEMBLY PART NO. R634 ITEM NO. PART NO. DESCRIPTION 1 U252503072 TUBE 2 1/2 x 2 1/2 x 3/16"W x 72" LG. 2 R6064 TINE PIPE FOR 1/2" (4-TINE) 1/2" - 5 TINE HARROW ASSEMBLY PART NO. R635 ITEM NO. PART NO. DESCRIPTION 1 U252503092 TUBE 2 1/2 x 2 1/2 x 3/16"W x 92" LG. 2 R6065 TINE PIPE FOR 1/2" (5-TINE) 1/2" - 6 TINE HARROW ASSEMBLY PART NO. R636 ITEM NO. PART NO. DESCRIPTION 1 U252503112 TUBE 2 1/2 x 2 1/2 x 3/16"W x 112" LG. 2 R6066 TINE PIPE FOR 1/2" (6-TINE) COMMON PARTS ITEM NO. PART NO. DESCRIPTION 3 R30002 1/2" TINE TUBE CONNECTOR 4 R30011 CLAMP BRACKET 5 B0812 1/2 X 1 1/4" BOLT 6 BN08L 1/2" NYLOCK NUT NC 7 BU1025 U-BOLT 5/8" x 2 1/2" x 4" 8 BN10L 5/8" NYLOCK NUT NC 9 R60000 1/2" WIRE - 20" DBL LEG SPRING TINE 10 R30007 ADJUSTING BRACKET WELDMENT 11 R30005 1/2" TINE 3 BAR ADJUST CONNECTOR 12 R30010 ADJUSTING BAR HD 3 BAR TINE 13 R30008 ADJUSTING BRACKET HANDLE WELDMENT 14 R9063.75 OD x.438 ID X 3/4 LONG SPACER 15 B0640 3/8"NC x 4" LG. HEX BOLT 16 BN06S 3/8"-16NC STOVER LOCK NUT 17 B0635 3/8"NC x 3 1/2" LG. HEX BOLT 18 R30015 LIGHT SAVER BRACKET 19 B0630 3/8"NC x 3" HEX BOLT 20 B0815 1/2" x 1 1/2" HEX BOLT 21 GHP11 #11 HAIR PIN 12-2007 Salford Farm Machinery Ltd. Page 35
2007 870 35' Disc Assembly and Parts Manual Подбор запасных частей на сайте: http://texagropark.ru Page 36 Salford Farm Machinery Ltd. 12-2007
12-2007 Salford Farm Machinery Ltd. Page 37
WING MOUNTED HARROW INSTALLATION 31 32 NOTE: USED ONLY WITH CERTAIN DISC MODELS 38 37 41 42 39 38 39 33 42 40 34 38 Page 38 Salford Farm Machinery Ltd. 12-2007
WING MOUTED HARROW INSTALLATION ITEM NO. QTY. PART NO. DESCRIPTION 31 4 D10053 3 1/2" EXTENSION 32 2 U40604100 TUBE 4" x 6" x 1/4"W x 100" LG. 33 8 RB1091 62" HARROW ARM ASSEMBLY 34 2 R636 6-1/2" TINE HARROW ASSY W/ OUTER RH HANDLE 37 4 MR1405R 5' ROLLER WITH FRAME RH 14" 38 32 BU1061 5/8" x 6" x 5 1/2" U-BOLT 39 64 BN10L 5/8" NYLOCK NUT NC 40 16 BU0825 1/2" x 2 1/2" x 3 1/2" U-BOLT 41 16 BU0820 1/2" x 2" x 3" U-BOLT 42 64 BN08L 1/2" NYLOCK NUT NC MAINFRAME MOUNTED HARROW INSTALLATION (NO EXTENSIONS SEE LAYOUT) QTY. PART NO. DESCRIPTION 6 RB1091 62" HARROW ARM ASSEMBLY 2 R635 5-1/2" TINE HARROW ASSY W/ OUTER RH HANDLE 3 MR1405R 5' ROLLER WITH FRAME RH 14" 12 BU1061 5/8" x 6" x 5 1/2" U-BOLT 24 BN10L 5/8" NYLOCK NUT NC 12 BU0825 1/2" x 2 1/2" x 3 1/2" U-BOLT 12 BU0820 1/2" x 2" x 3" U-BOLT 48 BN08L 1/2" NYLOCK NUT NC Подбор запасных частей на сайте: http://texagropark.ru 12-2007 Salford Farm Machinery Ltd. Page 39
870-35' HARROW LAYOUT 2007 870 35' Disc Assembly and Parts Manual 5 TINES 26 3/4" 6 TINES SPACER MUST 30" BE 3" MIN. 35 3/4" 40" 35" 20" 9" 6 TINES 24 1/2" 5 TINES 9" 30" 15" 42" 40" 35 7/8" 18" TUBES ADDED FOR HARROW ARM HANGERS 100" 100" 5' RH 5' RH 5' RH 5' RH 5' RH 5' RH 5' RH Page 40 Salford Farm Machinery Ltd. 12-2007
870 TOW HITCH INSTALLATION ITEM NO. PART NUMBER DESCRIPTION QTY. 3 MD873 TOW HITCH WELDMENT - 870 DISC 1 4 BU1046 U-BOLT 5/8" x 4" x 7 1/2" LG. 6 5 BN10L 5/8" NYLOCK NUT NC 12 4 3 5 Подбор запасных частей на сайте: http://texagropark.ru 12-2007 Salford Farm Machinery Ltd. Page 41