ABRASIVES. Diamond Blade Troubleshooting. Multi-Air Backing Pads. Fibre Disc Back-Up Pads - Standard Performance

ABRASIVES 26 Diamond Blade Troubleshooting Diamond blade does not cut: Cause: The blade is too hard for the material being cut. Solution: Use a softer blade specification. Cause: The segments have become blunt & polished. Solution: Sharpen the segments by cutting in to an abrasive material such as sandstone or abrasive concrete block. If segments continue to become blunt use a softer blade. Cause: Insufficient machine power. Solution: Check that the drive belts are tight and in good condition. Check that the line voltage to motor is correct. Excessive blade wear: Cause: The blade is too soft for the material being cut. Solution: Use a harder blade specification. Cause: Blade speed too low. Solution: Increase speed on machine or change machine type. Cause: Poor water supply. Solution: Make sure water hoses are clean and free from blockages. Cause: Machine Power too high. Solution: Ensure the blade used is suitable for the power of the machine. The more power the higher the diamond content and quality of blade required. Cracking of segments and/or steel centre: Cause: Blade is too hard for the material being cut. Solution: Use a softer blade specification. Cause: Blade running at excessive speed. Solution: Check that the blade shaft it running at the correct speed with a tachometer. Cause: Blade is out of tension. Solution: Replace blade or have the blade re-tensioned. Segment Loss. Cause: Blade is too hard for the material being cut. Solution: Use a softer blade specification. Cause: Material moved during cutting. Solution: Hold material securely when cutting. Cause: Steel core worn thin under segment. Solution: Use a blade with undercut protection segments when cutting abrasive materials such as asphalt. Avoid cutting into abrasive road base and increase water flow to blade if possible to wash out the debris from the cut. Uneven segment wear: Cause: Segments worn on one side of the blade. Solution: Make sure water feed pipes are clean and free from blockages on both sides of the blade. Cause: Blade not cutting straight. Solution: Check the saw alignment and ensure flanges are clean and free from dirt and of the same size. Blade worn out of round. Cause: The blade is too hard for the material being cut. Solution: Use a softer blade specification. Cause: Worn or damaged spindle and/or bearings. Solution: Replace spindle and/or bearings. Cause: Oversized or damaged bore. Solution: Use a new diamond blade and/or return damaged blade to the manufacturer for possible repair. Cause: Engine is surging. Solution: Service and tune engine so it runs smoothly. Blade Wobbles. Cause: Worn or damaged spindle and/or bearings. Solution: Replace spindle and/or bearings. Cause: Flanges are different diameters or too small. Solution: Make sure flanges are of correct diameter for the blade, and are of the same diameter. Cause: Excessive operator cutting pressure. Solution: Use a steady even infeed pressure and always cut in a straight line. Cause: Blade is out of tension. Solution: Replace blade or have the blade re-tensioned. Cause: Blade is bent or damaged. Solution: Replace the blade. Undercutting. Cause: Steel core worn thin under segment. Solution: Use a blade with undercut protection segments when cutting abrasive materials such as asphalt. Avoid cutting into abrasive road base and increase water flow to blade if possible to wash out the debris from the cut. discs - back up pads Multi-Air Backing Pads Together with the Multi-Air disc, the backing pad is the other patented sanding system included in the Multi-Air Process. It can be applied to all orbital sander machines, and thanks to the innovative design which draws the dust into a collecting chamber, it allows optimal airflow and powerful dust extraction. 150mm x Multi-Air AM489859 AM489860 Fibre Disc Back-Up Pads - Standard Performance Medium Density Soft Density Size mm AM991001 102 x M10-1.50 Fits most 100mm machines AM097463 100 x M10-1.25 To suit Makita AM991027 115 x M14-2.00 Fits most 115mm machines AM991040 125 x M14-2.00 Fits most 125mm machines AM991053 178 x M14-2.00 Fits most 178mm machines Fibre Disc Turbo Back-Up Pads - High Performance Part No. Size mm AM385611 102 x M10-1.50 Fits most 100mm machines AM385638 115 x M14-2.00 Fits most 115mm machines AM991066 125 x M14-2.00 Fits most 125mm machines AM991079 178 x M14-2.00 Fits most 178mm machines Sponge Interface Pads for Speedgrip Discs Part No. AM328030 AM337293 Speed-Grip Back-Up Pads Part No. AM232041 AM257338 150mm x 6 Holes 150mm x 9 Holes 150mm SGP6-5/16 U.N.F. 150mm SGRP6-5/16 6 Hole AM257346 200mm SGP8M - M14 No Hole

ABRASIVES Medium Speed-Grips Pads (Stick 'n' Sand Pads Available) AM387711 AM387738 AM387746 150mm x No hole 150mm x 6+1 hole 150mm x 8+1 hole Bear-Tex Rapid Blend Surface Conditioning Flap Discs Bear-Tex Rapid Blend Flap Discs are a format of the coated abrasive flap disc using Bear-Tex Surface Conditioning material as the flap component. The new Rapid Blend Discs give a less aggressive cutting action and will retain a constant finish throughout the life of the disc. Ideal for light metal removal, edge breaking and weld blending in metal fabrication on Aluminium, Steels, Titanium and Inconel. Size mm Grade /Colour CX389048 125 x 22 Coarse / Brown CX389056 125 x 22 Medium / Maroon CX389064 125 x 22 Very Fine / Blue Bear-Tex Back-up Pads (Long Hooks for Surface Conditioning Material) For Surface Blending Discs. CX246085 CX246069 100mm diameter M10-1.25 100mm diameter M10-1.5 CX381403 115mm diameter M14-2 CX383767 127mm diameter M14-2 CX235105 178mm diameter M14-2 discs - back up plate Zec Grinding Disc Support Pad Zec Discs / Support Pads are fitted to angle grinders with standard depressed centre grinding wheel locking nuts. Size 8318115 115/125mm - Individually Display Card 8318140 180mm Zec Disc Support Pad STE Surface Blending Discs Surface blending discs deliver superior, consistent finishes whenever you need to clean, deburr, blend or finish all types of metal, wood and plastic. Size mm Brown Coarse CX235059 100 x Blank CX383686 115 x Blank CX383694 127 x Blank CX235083 178 x Blank Maroon Medium CX235040 100 x Blank CX383708 115 x Blank CX383716 127 x Blank CX235075 178 x Blank Blue Very Fine CX383724 100 x Blank CX383732 115 x Blank CX383740 127 x Blank CX235067 178 x Blank Disc converter kit discs - bear-tex Bear-Tex Rapid Strip Discs Cleaning and conditioning without loading. Preparing surfaces before welding. Cleaning and conditioning after welding. Paint and epoxy coating removal. Size mm CX353787 100 x 6 Bear-Tex Rapid Strip Depressed Centre Discs Surface preparation. Rapid cleaning and conditioning Size mm 30651 100 x 16 09649 115 x 22 Size mm CX353795 180 x 22 Rapid paint and coating removal. Rapid rust and residue removal Size mm 30655 125 x 22 09586 180 x 22 Speed-Grip Converter Kit (Self Adhesive) Converts Stick-on Pads to Speed-Grip System. AM379816 125mm x No Holes AM339822 150mm x No Holes AM379824 150mm x 9 Holes AM339725 178mm x No Holes AM379832 200mm x No Holes AM379840 200mm x 8 Holes AM379859 230mm x No Holes AM379867 250mm x No Holes AM379875 305mm x No Holes AM379883 356mm x No Holes Other sizes available. 27

discs - clean & strip DISCs - fibre ABRASIVES Scotch-Brite Clean and Strip XT-DC Disc Excellent for cleaning rust, paint, and other surface contaminates, while reducing damage to the underlying surface Reduces rework caused by gouging and undercutting from some traditional abrasives Raised hub allows for easy attachment to most popular angle grinders XC000777315 XC000777323 Size mm 100 x 16 CH 115 x 22 CH Scotch-Brite Clean and Strip Discs - Shaft Mounted XC000777331 XC000777349 125 x 22mm CH 180 x 22mm CH Extra coarse, open web is designed to handle tough cleaning, coating removal and stripping jobs faster, more effective and safer than wire brushes without loading Use on straight shaft tools with collets or chucks Available with either one or two discs on a 6mm diameter shaft FN510078085 1 Disc (CG-ZS) 75mm 0267203 (CG-ZS) 100mm 0267211 (CG-ZS) 150mm FN510078853 FN510078267 FN510078507 2 Disc (CG-ZS) 75mm (CG-ZS) 100mm (CG-ZS) 150mm ALOX Fibre Discs Fibre Discs for use on steel, non ferrous metals, plastics, aluminium and wood. Size 69400019 FS 100-16 A16 100mm (4 ) 69401016 FS 100-16 A24 100mm (4 ) 69401015 FS 100-16 A36 100mm (4 ) 69401023 FS 100-16 A60 100mm (4 ) 69401024 FS 100-16 A80 100mm (4 ) 69401019 FS 100-16 A100 100mm (4 ) 69401067 FS 100-16 A120 100mm (4 ) 64101111 FS 115-22 A16 115mm (4 1/2 ) 64102111 FS 115-22 A24 115mm (4 1/2 ) 64103111 FS 115-22 A36 115mm (4 1/2 ) 64106111 FS 115-22 A60 115mm (4 1/2 ) 64108111 FS 115-22 A80 115mm (4 1/2 ) 64110111 FS 115-22 A100 115mm (4 1/2 ) 64112111 FS 115-22 A120 115mm (4 1/2 ) 64101125 FS 125-22 A16 125mm (5 ) 64102125 FS 125-22 A24 125mm (5 ) 64103125 FS 125-22 A36 125mm (5 ) 64106125 FS 125-22 A60 125mm (5 ) 64108125 FS 125-22 A80 125mm (5 ) 64110125 FS 125-22 A100 125mm (5 ) 64112125 FS 125-22 A120 125mm (5 ) 64101175 FS 180-22 A16 180mm (7 ) 64102175 FS 180-22 A24 180mm (7 ) 64103175 FS 180-22 A36 180mm (7 ) 64106175 FS 180-22 A60 180mm (7 ) 64108175 FS 180-22 A80 180mm (7 ) 64110175 FS 180-22 A 100 180mm (7 ) 64112175 FS 1800-22 A120 180mm (7 ) 28 Scotch-Brite Clean and Strip Discs Extra coarse with an open web is designed to handle tough cleaning, coating removal and stripping jobs faster, more effective and safer than wire brushes without loading CX-DC are more durable and faster acting than the original black version Can be used as single discs or multiple loaded onto a spindle and used on edge Use No. 934 mandrel for mounting to straight shafted tools 0286237 CS-DC 100 x 6mm CH 0286245 CS-DC 150 x 12mm CH 0286252 CS-DC 178 x 20mm CH AC010565086 CX-DC 102 x 6mm CH AC010565078 CX-DC 152 x 13mm CH AN000417467 CX-DC 178 x 20mm CH

ABRASIVES discs - fibre - blaze BLAZE F980 Fibre Backed Discs The next generation of ceramic fibre discs for metal working applications. Cut cooler and last longer than current generation of fibre discs. Extra heavy fibre backing for the more robust grinding applications. Lower total grinding cost on stainless steel, cobalt, chrome, inconel, titanium and other hard to grind materials. Size mm Grade Grit Size 53168 100 x 16 F980 C24 53170 100 x 16 F980 C36 85524 100 x 16 F980 C50 62965 100 x 16 F980 C60 62966 100 x 16 F980 C80 36181 100 x 16 F980 C120 98000 115 x 22 F980 C24 98001 115 x 22 F980 C36 98002 115 x 22 F980 C50 98003 115 x 22 F980 C60 98004 115 x 22 F980 C80 25332 115 x 22 F980 C120 98005 125 x 22 F980 C24 98006 125 x 22 F980 C36 98007 125 x 22 F980 C50 98008 125 x 22 F980 C60 98009 125 x 22 F980 C80 09084 125 x 22 F980 C120 98010 178 x 22 F980 C24 98011 178 x 22 F980 C36 98012 178 x 22 F980 C50 98013 178 x 22 F980 C60 98014 178 x 22 F980 C80 11528 178 x 22 F980 C120 Zirconia Fibre Discs Fibre Discs for use on steel, non ferrous metals, plastics, aluminium and wood. Size 69400014 FS 100-16 Z24 100mm (4 ) 69400016 FS 100-16 Z36 100mm (4 ) 69400017 FS 100-16 Z60 100mm (4 ) 69400018 FS 100-16 Z80 100mm (4 ) 69400015 FS 100-16 Z120 100mm (4 ) 64202111 FS 115-22 Z24 115mm (4 1/2 ) 64203111 FS 115-22 Z36 115mm (4 1/2 ) 64206111 FS 115-22 Z60 115mm (4 1/2 ) 64208111 FS 115-22 Z80 115mm (4 1/2 ) Zirconia Fibre Discs cont. Fibre Discs for use on steel, non ferrous metals, plastics, aluminium and wood. Size 64212111 FS 115-22 Z120 115mm (4 1/2 ) 64202125 FS 125-22 Z24 125mm (5 ) 64203125 FS 125-22 Z36 125mm (5 ) 64206125 FS 125-22 Z60 125mm (5 ) 64208125 FS 125-22 Z80 125mm (5 ) 64212125 FS 125-22 Z120 125mm (5 ) 64202175 FS 180-22 Z24 180mm (7 ) 64203175 FS 180-22 Z36 180mm (7 ) 64206175 FS 180-22 Z60 180mm (7 ) 64208175 FS 180-22 Z80 180mm (7 ) 64212175 FS 180-22 Z120 180mm (7 ) disc - lockit Quick-Change Discs Merit Abrasives through Saint-Gobain Abrasives offer a selection of Quick-Change Discs with the Speedlok fastening system. Speedlok is compatible to 3M Roloc fastening system. Ideal for deburring, blending, cleaning and polishing a variety of materials in a wide range of industries including mining, automotive, metal fabricators, toolrooms, etc. Part No. Size mm Diameter Material Type Grit Size 492402 51 Alo 36 492404 51 Alo 50 492406 51 Alo 80 492408 51 Alo 120 498404 51 Power Zirc 50 498406 51 Power Zirc 80 492426 51 Zirconia 36 492429 51 Zirconia 60 492430 51 Zirconia 80 440381 51 Surface Conditioning Coarse (Tan) 440382 51 Surface Conditioning Medium (Maroon) 440383 51 Surface Conditioning Very Fine (Blue) 492502 75 Alo 36 492504 75 Alo 50 492506 75 Alo 80 492508 75 Alo 120 498504 75 Power Zirc 50 498506 75 Power Zirc 80 492526 75 Zirconia 36 492529 75 Zirconia 60 492530 75 Zirconia 80 595512 75 Ceramic 36 595515 75 Ceramic 60 595516 75 Ceramic 80 595518 75 Ceramic 120 440481 75 Surface Conditioning Coarse (Tan) 440482 75 Surface Conditioning Medium (Maroon) 440483 75 Surface Conditioning Very Fine (Blue) Holder Pads with 1/4 Diameter Spindle AM337218 51 Medium Firmness 25,000 rpm AM325643 75 Medium Firmness 20,000 rpm 29

discs - metalite fibre discs - norzon fibre plus ABRASIVES Metalite Fibre Backed Discs Tough, durable aluminium oxide abrasive for fast initial cut. Closekote for weld grinding and blending of metal surfaces. Light deburring and finishing. Size mm Grade Grit Size CD106038 100 x 16 F226 P16 CD106496 100 x 16 F226 P24 CD106399 100 x 16 F226 P36 CD106186 100 x 16 F226 P50 CD106275 100 x 16 F226 P60 CD105821 100 x 16 F226 P80 CD105899 100 x 16 F226 P100 CD165239 100 x 16 F226 P120 CD106488 115 x 22 F226 P24 CD106356 115 x 22 F226 P36 CD106178 115 x 22 F226 P50 CD106267 115 x 22 F226 P60 CD105813 115 x 22 F226 P80 CD139092 115 x 22 F226 P120 CD139289 125 x 22 F226 P16 CD106453 125 x 22 F226 P24 CD106321 125 x 22 F226 P36 CD106143 125 x 22 F226 P50 CD106224 125 x 22 F226 P60 CD105996 125 x 22 F226 P80 CD105856 125 x 22 F226 P100 CD105708 125 x 22 F226 P120 CD106526 178 x 22 F226 P16 CD106429 178 x 22 F226 P24 CD106313 178 x 22 F226 P36 CD106100 178 x 22 F226 P50 CD106216 178 x 22 F226 P60 CD105775 178 x 22 F226 P80 CD105619 178 x 22 F226 P100 CD105716 178 x 22 F226 P120 NorZon Plus Fibre Backed Discs for Industrial Stainless Steel Fabricators Norzon PLUS fibre discs are best used on stainless and heat sensitive steels. Norzon PLUS has a supersize coating which produces a cooler cutting action with extended disc life, when grinding or blending. Size mm Grade Grit Size 29135 100 x 16 F861 Z36 29137 100 x 16 F861 Z60 29138 100 x 16 F861 Z80 29139 100 x 16 F861 Z120 95190 115 x 22 F861 Z36 95192 115 x 22 F861 Z60 95193 115 x 22 F861 Z80 95194 115 x 22 F861 Z120 95195 125 x 22 F861 Z36 95198 125 x 22 F861 Z60 95199 125 x 22 F861 Z80 95200 125 x 22 F861 Z120 95201 180 x 22 F861 Z36 95204 180 x 22 F861 Z60 95206 180 x 22 F861 Z80 95207 180 x 22 F861 Z120 DISCS - ROLOC 30 discs - norzon fibre NorZon Fibre Backed Discs Premium self-sharpening zirconia aluminium oxide for fast, aggressive cut. Closekote for heavy stock removal of metal. Size mm Grade Grit Size CD150614 100 x 16 F827 Z24 CD194085 100 x 16 F827 Z36 CD193046 100 x 16 F827 Z60 CD211036 115 x 22 F827 Z24 CD123897 115 x 22 F827 Z36 CD021954 115 x 22 F827 Z60 CD383619 125 x 22 F827 Z24 CD123927 125 x 22 F827 Z36 CD150657 125 x 22 F827 Z60 CD123900 178 x 22 F827 Z24 CD123919 125 x 22 F827 Z36 CD123935 125 x 22 F827 Z60 Roloc Discs 361F - Provides a durable cloth backing designed for general purpose blending and deburring on all metals 777F - Works well on heat sensitive metals. Excellent for heavy grinding applications 983C - Designed for use in aggressive, high pressure grinding applications where premature edge wear may be a concern. Colour button on the back of the disc indicates the grade: Grit 24 = Black Grit, 36 = Brown, 50 = Green Grit, 60 = Orange, 80 = Yellow, 120 = White 0175968 P24 361F 75mm 60440208944 P36 361F 75mm 60440209025 P50 361F 75mm 0272765 P80 361F 75mm 0289421 P60 777F 75mm 60650017704 P80 777F 75mm 0290262 P120 777F 75mm 0318476 P36 983C 75mm 0318490 P50 983C 75mm 60440207102 P60 983C 75mm 0318552 P80 983C 75mm AC010582826 P120 983C 75mm

ABRASIVES discs - speed-grip - adalox Scotch-Brite Roloc Light Grinding and Blending Discs (LGB) Light grinding and blending is accomplished with a single disc, potentially eliminating sanding steps prior to painting Impregnated mineral throughout the disc which extends disc life and provides a consistent finish HD CRS = Heavy Duty Coarse, SD CRS = Super Duty Coarse Accessories: 3M Roloc back-up pads (p/n 45095) 50mm x ¼ in thread, (p/n 45092) 75mm x ¼ in thread, (p/n 84999) 75mm x M14-2.0 61500292661 HD CRS 50mm 61500292679 SD CRS 50mm Scotch-Brite Roloc Surface Conditioning Discs (SC-DR) 61500292687 HD CRS 75mm 61500292695 SD CRS 75mm Non-woven abrasive product used for cleaning, finishing, blending and deburring applications Provides a uniform finish Suitable for stainless steel, carbon steel and aluminium CRS = Coarse (Brown), MED = Medium (Maroon), VFN = Very Fine (Blue), SFN = Super Fine (Grey) Accessories: 3M Roloc back-up pads (p/n 45095) 50mm x ¼ in thread, (p/n 45092) 75mm x ¼ in thread, (p/n 84999) 75mm x M14-2.0 61500141736 CRS 50mm 0262246 MED 50mm 0262238 VFN 50mm 0346205 SFN 50mm Scotch-Brite Roloc Bristle Disc 61500141801 CRS 75mm 61500141793 MED 75mm 0262279 VFN 75mm 0262303 SFN 75mm Able to clean and remove paints, rust and light scale from surfaces without actually abrading the underlying surface Unique Cubitron mineral provides high cut, while the flexible, plastic bristles conform to the work piece Safer than some traditional coating removal methods such as wire technology 0382283 50G 50mm 0382291 80G 50mm 0382309 120G 50mm 0382325 50G 75mm 0382333 80G 75mm 0382341 120G 75mm Adalox Paper Backed Speed-Grip Discs Preparing primed and painted surfaces for finishing. Stripping primer and paint. Sanding of plastic and fibreglass. Light weld blending and deburring. Bare wood sanding. Finishing metal of all types. Size mm Grade Grit Size To suit: Triton R.O.S., B&D 190 CD343110 125 x Blank H211 P40E CD343129 125 x Blank H211 P60E CD343137 125 x Blank H211 P80E CD343145 125 x Blank H211 P120E CD343153 125 x Blank H211 P180E CD379662 125 x Blank H211 P240E To suit: Bosch PEX 125A, Makita BO5000, Metabo SXE 425, Hitachi FSV13Y, AEG, DeWalt DW421, B&D 190E CD300268 125 x 8 holes H211 P40E CD300276 125 x 8 holes H211 P60E CD300284 125 x 8 holes H211 P80E CD300288 125 x 8 holes H211 P100E CD300292 125 x 8 holes H211 P120E CD300306 125 x 8 holes H211 P180E CD336807 125 x 8 holes H211 P240E Other sizes available. disc - speed-grip - no-fil No-Fil Adalox A275 Paper Backed Speed-Grip Discs Premium P-graded, heat treated aluminium oxide abrasive for superior life, faster cut rate, consistent finish. Unique fibre-reinforced, B-wt latex-saturated backing for 50-60% improvement in tear strength. Flexible; can be used wet. Water-based stearate, non-pigmented, No-Fil coating provides maximum load resistance and extended life; no colour transfer to work. Openkote for finishing timber and painted surfaces. Size mm Grade Grit Size CD353496 80 x Blank A275 P80B CD353497 80 x Blank A275 P120B CD353498 80 x Blank A275 P150B CD353499 80 x Blank A275 P180B CD353500 80 x Blank A275 P240B CD353501 80 x Blank A275 P320B CD353502 80 x Blank A275 P400B CD353503 80 x Blank A275 P600B CD353504 80 x Blank A275 P800B CD353505 80 x Blank A275 P1200B CD353506 80 x Blank A275 P1500B CD257516 150 x Blank A275 P80B CD257524 150 x Blank A275 P100B CD257532 150 x Blank A275 P120B CD257710 150 x Blank A275 P150B CD257540 150 x Blank A275 P180B CD257559 150 x Blank A275 P240B CD257567 150 x Blank A275 P320B CD377937 150 x Blank A275 P600B 31

No-Fil Adalox A275 Paper Backed Speed-Grip Discs (cont.) Size mm Grade Grit Size CD353566 150 x 6+1 Hole Vacuum A275 P80B CD353574 150 x 6+1 Hole Vacuum A275 P120B CD353582 150 x 6+1 Hole Vacuum A275 P150B CD353590 150 x 6+1 Hole Vacuum A275 P180B CD353604 150 x 6+1 Hole Vacuum A275 P240B CD353612 150 x 6+1 Hole Vacuum A275 P320B CD353620 150 x 6+1 Hole Vacuum A275 P400B CD368946 150 x 6+1 Hole Vacuum A275 P500B CD353639 150 x 6+1 Hole Vacuum A275 P600B CD354775 150 x 6+1 Hole Vacuum A275 P800B CD353647 150 x 6+1 Hole Vacuum A275 P1200B CD353655 150 x 6+1 Hole Vacuum A275 P1500B DISC - surface conditioning Scotch-Brite Light Grinding and Blending Discs (LGB) Light grinding and blending is accomplished with a single disc, potentially eliminating sanding steps prior to painting Impregnated mineral throughout the disc which extends disc life and provides a consistent finish Use with Centre-Pin Contact Disc Pads for reduced tool vibration and risk of disc fly-off Accessories: Centre-Pin Back-Up Pads (p/n 61677) 100mm - M10-1.5. (p/n 61680) 115mm M14-2.0. (p/n 61681) 125mm x M14-2.0. (p/n 61682) 125mm x M14-2.0. 61500292497 HD CRS 100 x 16mm CH 61500292505 SD CRS 100 x 16mm CH 61500292448 HD CRS 115 x 22mm CH 61500292455 SD CRS 115 x 22mm CH 61500292489 HD CRS 125 x 22mm CH 61500292539 SD CRS 125 x 22mm CH 61500292596 HD CRS 180 x 22mm CH 61500292562 SD CRS 180 x 22mm CH ABRASIVES 32 CDR Type - Surface Conditioning Fibre Discs for use on steel, non-ferrous metals, plastics, aluminium and wood. G = Coarse (Brown), M = Medium (Maroon), S = Fine (Blue) Size 42781501 Non-Woven Discs CDR VRH 50 A Coarse 50mm (2 ) 42781502 Non-Woven Discs CDR VRH 50 A Medium 50mm (2 ) 42781504 Non-Woven Discs CDR VRH 50 A Very Fine 50mm (2 ) 42781751 Non-Woven Discs CDR VRH 75 A Coarse 75mm (3 ) 42781752 Non-Woven Discs CDR VRH 75 A Medium 75mm (3 ) 42781754 Non-Woven Discs CDR VRH 75 A Very Fine 75mm (3 ) 581C Fibre Discs Provides good performance and consistent quality finish, at economical price Alumina Zirconia mineral, with a Vulcanized Fibre backing A Thermoformed shape and slotted centre hole means the disc conforms to the back up pad, maximising disc life and creating safer working conditions Accessories: Back-Up Pads (p/n 07312) 100mm - M10-1.5 retaining nut. (p/n 09584) 125mm both a M14-2.0 & 5/8 in retaining nut included. (p/n 09921) 180mm both a M14-2.0 & 5/8 in retaining nut included GC800984475 GC800984608 GC800984681 GC800984723 GC800984582 GC800984632 GC800984707 GC800984749 GC800984558 GC800984590 GC800984665 GC800984731 GC800984566 P24 100 x 16mm P36 100 x 16mm P60 100 x 16mm P80 100 x 16mm P24 125 x 22mm P36 125 x 22mm P60 125 x 22mm P80 125 x 22mm P120 125 x 22mm P24 180 x 22mm P36 180 x 22mm P80 180 x 22mm P120 180 x 22mm Scotch-Brite Surface Conditioning Discs (SC-DH) Non-woven abrasive product used for cleaning, finishing, blending and deburring applications Provides a uniform finish Suitable for stainless steel, carbon steel and aluminium Use with Centre-Pin Contact Disc Pads for reduced tool vibration and risk of disc fly-off CRS = Coarse (Brown), MED = Medium (Maroon), VFN = Very Fine (Blue), SFN = Super Fine (Grey) Accessories: Centre-Pin Back-Up Pads (p/n 61677) 100mm - M10-1.5. (p/n 61680) 115mm M14-2.0. (p/n 61681) 125mm x M14-2.0. (p/n 61682) 125mm x M14-2.0. 61500291838 CRS 125 x 22mm CH 61500291820 MED 125 x 22mm CH 61500291812 VFN 125 x 22mm CH 61500291895 SFN 125 x 22mm CH 61500291853 CRS 180 x 22mm CH 61500291507 MED 180 x 22mm CH 61500291846 VFN 180 x 22mm CH 61500291903 SFN 180 x 22mm CH DISCs - fibre - combi click Combi Click Fibre Discs Alox - For general purpose grinding work from coarse to fine grinding in industry and trades. Ceramic Cool - For high performance CC-Grind - For grinding applications Size 64190103 Abr. Disc CC-FS 125 A 36 125mm (5 ) 64190106 Abr. Disc CC-FS 125 A 60 125mm (5 ) 64190108 Abr. Disc CC-FS 125 A 80 125mm (5 ) 64190112 Abr. Disc CC-FS 125 A 120 125mm (5 ) 64193106 Abr. Disc CC-FS 125 CO-COOL 60 125mm (5 ) 64193108 Abr. Disc CC-FS 125 CO-COOL 80 125mm (5 ) 64193112 Abr. Disc CC-FS 125 CO-COOL 120 125mm (5 ) 64183125 CC-Grind Disc 125 Steel 125mm (5 ) 44890150 Backing Pad CC-GT 115-125 M14 125mm (5 )

ABRASIVES FAN GRINDERS flap discs - aluminium oxide ALOX Fan Grinders High stock removal rate due to aggressive abrasive materials. The textile elements wear off uniformly and without residue on the material surface. Size 44400086 Fan Grinder F 2010/6 A 80 20 x 10 47800090 Fan Grinder F 2515/6 A 60 25 x 15 44410086 Fan Grinder F 2525/6 A 80 25 x 25 44402066 Fan Grinder F 3010/6 A 60 30 x 10 44402086 Fan Grinder F 3010/6 A 80 30 x 10 47801092 Fan Grinder F 4020/6 A 60 40 x 20 44408086 Fan Grinder F 4020/6 A 80 40 x 20 44505066 Fan Grinder F 5010/6 A 60 50 x 10 44503066 Fan Grinder F 5030/6 A 60 50 x 30 44503086 Fan Grinder F 5030/6 A 80 50 x 30 44509046 Fan Grinder F 6030/6 A 40 60 x 30 44509066 Fan Grinder F 6030/6 A 60 60 x 30 44509086 Fan Grinder F 6030/6 A 80 60 x 30 44516046 Fan Grinder F 8050/6 A 40 80 x 50 Note: A full range of Sizes and Grits is available. flap discs - alum oxide Premium SG Polifans - ALOX Ideal for grinding use on bar, angle iron, flat bar, sheet steel, welds and tube. Size 67604100 FLAP DISC PFF 100 A 40 SG 100mm (4 ) 67606100 FLAP DISC PFF 100 A 60 SG 100mm (4 ) 67608100 FLAP DISC PFF 100 A 80 SG 100mm (4 ) 67612100 FLAP DISC PFF 100 A 120 SG 100mm (4 ) 67704115 FLAP DISC PFC 115 A 40 SG 115mm (4 1/2 ) 67706115 FLAP DISC PFC 115 A 60 SG 115mm (4 1/2 ) 67708115 FLAP DISC PFC 115 A 80 SG 115mm (4 1/2 ) 67712115 FLAP DISC PFC 115 A 120 SG 115mm (4 1/2 ) 67704125 FLAP DISC PFC 125 A 40 SG 125mm (5 ) 67706125 FLAP DISC PFC 125 A 60 SG 125mm (5 ) 67708125 FLAP DISC PFC 125 A 80 SG 125mm (5 ) 67712125 FLAP DISC PFC 125 A 120 SG 125mm (5 ) 67702185 FLAP DISC PFC 180 A 24 SG 180mm (7 ) 67704185 FLAP DISC PFC 180 A 40 SG 180mm (7 ) 67706185 FLAP DISC PFC 180 A 60 SG 180mm (7 ) 67708185 FLAP DISC PFC 180 A 80 SG 180mm (7 ) 67712185 FLAP DISC PFC 180 A 120 SG 180mm (7 ) Note: A full range of sizes and grits is available. Flap Discs - Aluminium Oxide Manufactured in high quality Aluminium Oxide grain with glass fibre backing to give superior performance. Part No. Size mm Grit Specs Max R.P.M. 9890040 100 x 16 40 A/O GFCA 15000 9890060 100 x 16 60 A/O GFCA 15000 9890080 100 x 16 80 A/O GFCA 15000 9890120 100 x 16 120 A/O GFCA 15000 9891040 115 x 22 40 A/O GFCA 13000 9891060 115 x 22 60 A/O GFCA 13000 9891080 115 x 22 80 A/O GFCA 13000 9893040 125 x 22 40 A/O GFCA 12000 9893060 125 x 22 60 A/O GFCA 12000 9893080 125 x 22 80 A/O GFCA 12000 9893120 125 x 22 120 A/O GFCA 12000 9892040 180 x 22 40 A/O GFCA 8600 9892060 180 x 22 60 A/O GFCA 8600 9892080 180 x 22 80 A/O GFCA 8600 9892120 180 x 22 120 A/O GFCA 8600 flap disc - blaze SG Blaze R980 Flap Discs New SG Blaze flap discs demonstrated to last 50 to 200% longer on hard-to-grind materials. Featuring next generation SG ceramic grain, designed to continually fracture during grinding to expose new cutting edges. Part No. Size mm Grit Specs Max R.P.M. 12097 100 x 16 40 R980 15000 93211 100 x 16 60 R980 15000 12098 100 x 16 80 R980 15000 83487 115 x 22 40 R980 13000 83488 115 x 22 60 R980 13000 83489 115 x 22 80 R980 13000 90002 125 x 22 40 R980 12000 90003 125 x 22 60 R980 12000 90004 125 x 22 80 R980 12000 83495 180 x 22 40 R980 8600 83496 180 x 22 60 R980 8600 83497 180 x 22 80 R980 8600 flap discs - curve NEW! Polifan Curve The new POLIFAN CURVE SG-PLUS flap disc has an innovative radial shape to optimize fillet weld operations on steel and INOX workpieces. POLIFAN CURVE SG-PLUS flap discs are specially designed to provide fast, aggressive grinding with a very high rate of material removal. Size 67689052 FLAP DISC PFR 125 Z 40 SGP-Curve-M 125mm (5 ) 67689062 FLAP DISC PFR 125 Z 40 SGP-Curve-L 125mm (5 ) 67689056 FLAP DISC PFR C060-Curve-M 125mm (5 ) 67689066 FLAP DISC PFR C060-Curve-L 125mm (5 ) 33

FLAP DISCS - STRONG NEW! Polifans - Strong The patented construction of the POLIFAN STRONG flap disc provides extraordinary stability. The extended flap length allows for continued aggressive grinding up to the last grain. Removes more material in less time than any grinding wheel or competitve flap disc on the market! Size 67788015 FLAP DISC PFC 115 Z 36 SGP-Strong 115mm (4 1/2 ) 67788115 FLAP DISC PFC 115 Z 50 SGP-Strong 115mm (4 1/2 ) 67788025 FLAP DISC PFC 125 Z 36 SGP-Strong 125mm (5 ) 67788125 FLAP DISC PFC 125 Z 50 SGP-Strong 125mm (5 ) Zirconium Flap Discs cont. Diameter Bore Maximum Safe Grit (mm) (mm) Speed (RPM) FDBZ11522080 115 22 80 13,300 FDBZ11522120 115 22 120 13,300 FDBZ12722036 127 22 36 12,000 FDBZ12722040 127 22 40 12,000 FDBZ12722060 127 22 60 12,000 FDBZ12722080 127 22 80 12,000 FDBZ12722120 127 22 120 12,000 FDBZ18022036 180 22 36 8,600 FDBZ18022040 180 22 40 8,600 FDBZ18022060 180 22 60 8,600 FDBZ18022080 180 22 80 8,600 FDBZ18022120 180 22 120 8,600 ABRASIVES 34 flap discs - ZIRCONIA Premium SG Polifans - Zirconia Ideal for grinding use on bar, angle iron, flat bar, sheet steel, welds and tube. Size 67650104 FLAP DISC PFF 100 Z 40 SGP-SPECIAL 100mm (4 ) 67650106 FLAP DISC PFF 100 Z 60 SGP-SPECIAL 100mm (4 ) 67650108 FLAP DISC PFF 100 Z 80 SGP-SPECIAL 100mm (4 ) 67784115 FLAP DISC PFC 115 Z 40 SG 115mm (4 1/2 ) 67786115 FLAP DISC PFC 115 Z 60 SG 115mm (4 1/2 ) 67750208 FLAP DISC PFC 115 Z 80 SGP-SPECIAL 115mm (4 1/2 ) 67784125 FLAP DISC PFC 125 Z 40 SG 125mm (5 ) 67786125 FLAP DISC PFC 125 Z 60 SG 125mm (5 ) 67750308 FLAP DISC PFC 125 Z 80 SGP-SPECIAL 125mm (5 ) 67784185 FLAP DISC PFC 180 Z 40 SG 180mm (7 ) 67786185 FLAP DISC PFC 180 Z 60 SG 180mm (7 ) 67750408 FLAP DISC PFC 180 Z 80 SGP-SPECIAL 180mm (7 ) Zirconium Flap Discs Garryson HEAVY DUTY Flap Discs Garryson Heavy Duty Flap Discs are manufactured using reinforced glass fibre backs and zirconia grit. These flap discs are particularly suited to weld removal, grinding and clean up on steel, stainless steel and aluminium. Discs fit directly onto machine - no backing pads are needed. Diameter (mm) Bore (mm) Grit Maximum Safe Speed (RPM) FDBZ10016036 100 16 36 15,300 FDBZ10016040 100 16 40 15,300 FDBZ10016060 100 16 60 15,300 FDBZ10016080 100 22 80 15,300 FDBZ10016120 100 22 120 15,300 FDBZ11522036 115 22 36 13,300 FDBZ11522040 115 22 40 13,300 FDBZ11522060 115 22 60 13,300 Megaline Blue Flap Discs - Zirconia Manufactured in high quality Zirconia grain with glass fibre backing to give superior performance. Part No. Size mm Grit Specs Max R.P.M. 9800040 100 x 16 40 Zirc GFCZ 15000 9800060 100 x 16 60 Zirc GFCZ 15000 9800080 100 x 16 80 Zirc GFCZ 15000 9800120 100 x 16 120 Zirc GFCZ 15000 9801040 115 x 22 40 Zirc GFCZ 13000 9801060 115 x 22 60 Zirc GFCZ 13000 9801080 115 x 22 80 Zirc GFCZ 13000 9801120 115 x 22 120 Zirc GFCZ 13000 9803040 125 x 22 40 Zirc GFCZ 12000 9803060 125 x 22 60 Zirc GFCZ 12000 9803080 125 x 22 80 Zirc GFCZ 12000 9803120 125 x 22 120 Zirc GFCZ 12000 9802040 180 x 22 40 Zirc GFCZ 8600 9802060 180 x 22 60 Zirc GFCZ 8600 9802080 180 x 22 80 Zirc GFCZ 8600 9802120 180 x 22 120 Zirc GFCZ 8600 flap discs - zirconia - megaline twin Flap Discs Excellent grinding and finishing: Weld grinding Rust removal Surface preparation Deburring Blending Paint removal Edge grinding Operator Friendly: Light pressure Light in weight Requires no back up pad. Material Applications: For aluminium, carbon steel, stainless steel, cast iron, plastics, bronze and brass. Megaline Twin Flap Discs - SG / Zirconia Twin Flap Discs are the latest innovation of Flap Discs, they use 2 cloths and alternately place one after the other. This technology develops a premium flap disc with high stock removal, fast cutting and cool grinding whilst delivering an extended disc life. Ideal for use on stainless steel and other heat sensitive materials. Part No. Size mm Grit Specs Max R.P.M. 9870040 100 x 16 40 SGZirc GFC 15000 9870060 100 x 16 60 SGZirc GFC 15000 9870080 100 x 16 80 SGZirc GFC 15000 9873040 125 x 22 40 SGZirc GFC 12000 9873060 125 x 22 60 SGZirc GFC 12000 9873080 125 x 22 80 SGZirc GFC 12000

ELECTRIC - POlisher 1200W Polisher - Variable Speed Variable Speed; 700-2,200 rpm Weight; 2.4Kg Pad; Ø175mm Spindle Thread; ØM14 Overload and Restart Protection Soft Start and Constant Torque Auto Stop Carbon Brushes Includes: Side handle, hand guard, pad : PE 12-175 250W Sander 250w Sander Random Orbit Variable speed MICROFILTER dust extraction Product Code: gex 125-1AE ELECTRIC - SANDER - POLISHER ELECTRIC - ROUTER POWER TOOLS 12mm (1/2 ) Plunge Router Linear ball bearing for super-smooth plunge action Precision cutting depth adjustment, cutting depth is adjustable in 0.1mm increments Easy to read cutting depth scale Quick depth setting button Stopper block enables to obtain 3 different cutting depths Tool-less one touch change of template guide : RP1800 ELECTRIC - SANDER - BELT 180mm Sander / Polisher Powerful 950W motor No-load speed range: 1900-3400rpm Two-speed dust sealed switch Robust construction for longer life : SAT180 180mm Variable Speed Sander/Polisher D shaped handle offers comfort and control to the user High power with a 1,250W motor Robust construction for longer life Variable speed dial and trigger : SP18VA 76mm Belt Sander Powerful and versatile - can use both 76mm and 100x610mm belts Fine adjustment tracking Large lever for quick belt changes Excellent for floor sanding, cleaning and smoothing off table and bench tops and can be connected to dust extraction system Low profile nose and extended roller Graphite pad for reduced belt wear and reduced heat in the sanding area : 9924DB ELECTRIC - SANDER - ORBITAL ELECTRIC - SAW - RECIPROCATING Recipro Saw 1,010W motor drives a more efficient cutting action with less wear and drain on the machine Strokes-per-minute have been increased by almost 20% on previous model Minimal vibration A bigger variable speed trigger with lock-on button Rubber cladding Push in tool-less blade change system with quick release : JR3050T 266 1/3 Sheet Orbital Sander Compact and lightweight design for easy handling and high manoeuvrability Powerful heavy-duty motor featuring increased power input obtained by redesigned cooling system Easy to operate paper with large clamp lever Rubberised soft grip Rigid aluminium foot with sponge sleeve provides high durability and effective vibration absorbing performance : BO3710X 1200W Reciprocating Sabre Saw Variable Speed: 0-2,600 Strokes p/m Sawing Blade Stroke; 28mm Toolless saw blade change Soft Start Saw blade rotatable by 180º Adjustable Depth Stop Includes: 3 x Saw Blades, carry case : PSE 1200

TM AIR TOOLS & EQUIPMENT (COMPRESSORS) angle grinders Angle Grinder Pad Size - 4 10,000 RPM 83 dba 90 PSI Length - 138mm Weight - 2kg : SM065 100mm (4 ) Angle Grinder Characteristics 229mm long 12000rpm 100mm capacity 1.7kg 566L/min max, 509L/min av air consumption Product Code: SP-1254 125mm (5 ) Angle Grinder Characteristics 229mm long 12000rpm 125mm capacity 1.7kg 566L/min max, 509L/min av air consumption Product Code: SP-1257 Nitto Angle Grinders Powerful and robust Compact dimensions allow easy access in confined spaces Double lock safety lever Wide variety of models available to suit most grinding applications Model Number Wheel Diameter Weight MAG25B 58mm 0.55 kg MAG40 Aust 100mm 1.4 kg MAG50 125mm 2.2 kg MLG70 180mm 3.4 kg belt sanders Nitto Belt Sanders B10N Adjustable 360 rotation Rear exhaust system Tracking of belts is positive and easy to adjust Double safety lock lever Model Number Belt Size Weight B10N 10 x 330mm 0.9 kg B20N 20 x 520mm 1.4 kg B30N 30 x 540mm 2.9 kg MLG70 BLOW GUNS 125mm Angle Grinder with Wheel - Heavy Duty 11,000 RPM Ideal for cleaning, deburring, grinding and high amounts of rust and material removal Equipped with a side handle for better handling during operation : CHPL1555 8mm Bent Pipe Blow Gun Ideal for general use and keeping work areas clean and tidy Maximum working pressure 232PSI (16bar) : 124140101 299

AIR TOOLS & EQUIPMENT (COMPRESSORS) needle scaler Nitto Needle Scalers JEX28 Nitto Jet Chisels are the only unit of its kind without internal springs Powered by a piston which produces no irregular power Adjusts automatically to any surface contour Model Number Standard Needle Size Body Type JT20 3mm (2mm optional) Straight, Popular JEX20 3mm (2mm optional) Straight, Anti-Vibration JEX24 3mm (2mm optional) Pistol, Universal JEX28 3mm, 4mm (2mm optional) Pistol, Heavy Duty Filter Regulator Polycarbonate bowl with Metal bowl guard 1/2 BSP Inlet/Outlet Max. working pressure 150 psig Automatic water drain Mounting bracket Robust Metal construction : 06.2432 riveters Needle Scaler 4600 bpm 19 needles (3.2 mm) Length 465mm Weight 2.8kg Avg Air Consumption: 8 cfm 226 lpm : 125 Air Powered Rivet Gun - Medium Duty 2,000lbs of pull Sets rivets up to 4.8mm in diameter : CHPL1539 nibbler Air Nibbler - Medium Duty 3,800 strokes per minute, provides the cutting powder to cut up to 1.5mm steel Cuts intricate patterns in sheet metal and aluminium without leaving burrs. : CHPL1519 Pneumatic Riveting Tool Heavy Duty Industrial 15mm stroke 1200lbs pulling power Sets 6.4mm rivets Complete in Sturdy Zip Pouch with Carry handle : FHFFS64 reciprocating saws Reciprocating Saw - Medium Duty 10,000 strokes/minute provides the cutting power to cut up to 1.5mm steel Cuts plastic, aluminium, fibreglass and sheet metal : CHPL1540 REGULATOR AIR Air Riveter Stroke length - 9/16 Blind rivet capacity - 3/16 90 PSI 76 dba Length - 156mm Weight - 2kg : SG0810 sanders Filter Regulator Polycarbonate bowl with Metal bowl guard 1/4 BSP Inlet/Outlet Maximum working pressure 150 psig Automatic water drain Mounting bracket Jamec Pem branded Pressure gauge Robust Metal construction : 06.2426 178mm Air Sander - Medium Duty 4500 RPMs designed to smooth welds, remove rust and remove body filler Built in regulator Requires a 2 stage air compressor Planetary gearing balances load on bearings and gears for greater power 15.1 SCFM average air consumption at 90PSI : CHPL1551 309

6 High Speed Sander 6 High Speed 3/16 Orbit Ultra Duty 12,000rpm Vacuum ready Weight: 0.87kg Ave Air Cons: 8 cfm 226 lpm Dust is channelled away from work, swirl free finish. : 4151/4151-HL Quick Change Screwdriver - Medium Duty At 10,500 RPMs and 120lbs of Torque, provides the power necessary to remove tight screws easily. Ideal for small fastening work in electronic products Computer assembly and automotive application Quick change chuck uses 1/4 Hex bits : CHSA1575 TYRE GAUGES AIR TOOLS & EQUIPMENT (COMPRESSORS) 310 Dual Action Sander - 10,000rpm - Heavy Duty 10,000 RPMs Designed for sanding wood, metal, fibreglass and autobody fillers : CHPL1504 Air Palm Sander Pad size - 6 11,000 RPM 76 dba Spindle thread - 5/16-24 Length - 163mm Weight - 0.8kg : SM095 saw Nitto Super Saw SSW-110 Cutting capacity 3mm in mild steel Low vibration and longer piston stroke improves cutting speed Rear exhaust system for chip-scattering free operation Model Number Stroke Speed Stroke Weight SSW-110 7,000 rpm 11mm 0.6 kg SCREWDRIVERS Air Screwdriver Torque - 10-90 in Lb Hex drive capacity - 1/4 1,800 RPM 83 dba Length - 196mm Weight - 1.3kg : SM120 Digital Tyre Gauge Aluminium body with oil resistant rubber casing 5psi to 150psi measuring range Accurate to ±1% Two position lever for inflation and deflation Display powered by two CR2032 Lithium batteries Battery life of 140 hours Can be turned on and off as required 1/4 BSP(f) inlet Can measure pressures in kpa, psi, kg/cm 2 and bar : 51114 Tyre Gauge Dual scale gauge Dual hold-on chuck lever Precision die cast body Certificate of calibration : 10.2000 TYRE INFLATOR Tyre Inflator Straight clip on chuck 50mm dial gauge with rubber impact protector : 02.0135 utility kit Utility Driver Kit Used extensively in the panel beating industry. Includes: Utility in-line driver Adaptor for rubber eraser or brush Adaptor for double black wheels Adaptor for single black wheel Water based paint rubber eraser Rubber eraser 6 x black strip wheels SM135 12 Piece Air Utility In-Line Driver Kit, 3,500 RPM, 83 dba SM135RH Adaptor for Rubber Eraser or Brush SM135RW Rubber Eraser SM135BW 6 Piece Black Strip Wheels SM135WW723 Wire Brushes, 23mm Coarse SM135WW523 Wire Brushes, 23mm Fine