Technicl informtion TI 271T/02/en 60021058 RTD Temperture Sensor omnigrd S- TR 88 RTD ssembly with extension neck Replceble insert PCP (4...20 ma), HART or PROFIBUS-PA electronics The TR 88 Omnigrd S rnge temperture sensors re resistnce thermometers designed for use in the hevy chemicl industry, in pplictions with high pressures, tempertures nd high flows. They re equipped with thermowell tht must be purchsed seprtely. The TR 88 temperture sensors re mde up of mesurement probe, n extension neck with thermowell connection, nd housing, which my contin the trnsmitter for the conversion of the vrible mesured. Thnks to its modulr configurtion, the TR 88 is suitble for ll industril processes with severe therml nd mechnicl stresses. PCP (4...20 ma, lso with enhnced ccurcy), HART nd PROFIBUS- PA 2-wire trnsmitters Pt 100 sensing element with clss A ccurcy (DIN EN 60751) or 1/3 DIN B Pt 100 wire wound (-200...600 C) or thin film (-50...400 C) Double Pt 100, for redundncy purposes Single Pt 100 with 4 wires connection, double Pt 100 with 3 wires ATEX II 1 or 1/2 GD EEx i certifiction EA clibrtion certificte Fetures nd benefits Customized immersion lengths Seprte extension neck Stinless steel, luminium or plstic housings, with protection grde from IP65 to IP67 Replceble minerl insulted insert, with dimeter of 3 or 6 mm
omnigrd S TR 88 Ares of ppliction Chemicl industry Energy industry Function nd system design Mesuring principle In the RTD (Resistnce Temperture Detector) thermometers, the sensing element consists of n electricl resistnce with vlue of 100 Ω t 0 C (clled Pt 100, in complince with stndrd DIN EN 60751) which increses t higher tempertures ccording to coefficient chrcteristic of the resistor mteril (pltinum). In industril thermometers tht comply with the DIN EN 60751 stndrd, the vlue of this coefficient is α = 3.85*10-3 C -1, clculted between 0 nd 100 C. Equipment rchitecture The Omnigrd S TR 88 temperture sensor is mde up of mesurement probe, n extension neck with thermowell connection nd housing (hed), which my contin trnsmitter or the terminls on the cermic block for electricl connection. Construction of the sensor is bsed on the following stndrds: DIN 43729 (housing), 43772 (neck) nd 43735 (probe), nd cn therefore gurntee, together with suitble thermowell, good level of resistnce to the most typicl nd common industril processes. The mesurement probe (insert) is tensioned by mens of springs nd therefore mintined in contct with the lower bse of protection thermowell to enhnce the het trnsfer. The sensing element (Pt 100) is positioned close to the tip of the probe. The TR 88 cn be fitted on the plnt (tube or tnk) through the use of the connection to the thermowell, which cn be purchsed seprtely. The electricl structure of the thermometer lwys complies with DIN EN 60751 stndrd rules. The sensing element is vilble in two versions with thin film (TF) or wire wound (WW), the ltter with lrge mesurement nd ccurcy rnge. The housing cn be of different types nd mterils (plstic, pinted luminium lloy, stinless steel). The wy in which it fits to extension neck nd the cble glnd ensure minimum grde of IP65 (Ingress Protection). TR88_G_gd_07_xx_01 Fig. 1: TR 88 with vrious types of heds Mteril Extension neck in SS 316Ti/1.4571 Insert sheth in SS 316L/1.4404 Weight From 1 to 2.0 kg for stndrd options. 2 Endress+Huser
omnigrd S TR 88 Electronics The required type of output signl cn be obtined by choosing the correct hed-mounted trnsmitter. Endress+Huser supplies "stte-of-the-rt" trnsmitters (the itemp series) built in 2-wire technology nd with 4 20 ma output signl, HART or PROFIBUS-PA. All of the trnsmitters cn be esily progrmmed using personl computer through the RedWin 2000 public domin softwre (for trnsmitters 4 20 ma nd HART ) or the Commuwin II softwre (for PROFIBUS- PA trnsmitters). The HART trnsmitters cn lso be progrmmed with the hnd-held operting module DXR 275 (Universl HART Communictor). A PCP (4 20 ma, TMT 180) model with enhnced ccurcy is vilble. In the cse of PROFIBUS-PA trnsmitters, E+H recommends the use of PROFIBUS dedicted connectors. The Weidmüller type (Pg 13.5 - M12) is provided s stndrd option. For detiled informtion bout trnsmitters, plese refer to the relevnt documenttion (refer to the TI codes t the end of the document). If hed-mounted trnsmitter is not employed, the sensor probe cn be connected through the terminl block to remote converter (i.e. DIN ril trnsmitter). Performnce Operting conditions Ambient temperture (housing without hed-mounted trnsmitter) metl housings plstic housings Ambient temperture (housing with hed-mounted trnsmitter) Ambient temperture (housing with disply) Process temperture Sme of mesurement rnge (see below). Mximum process pressure nd mximum flow velocity Depending on the type of thermowell used. Shock nd vibrtion resistnce According to DIN EN 60751-40 130 C -40 85 C -40 85 C -20 70 C 3 g pek / 10 500 Hz Accurcy Probe mximum error (type TF) cl. A 3σ = 0.15+0.0020It 50 250 C 3σ = 0.30+0.0050ItI 250 400 C cl. 1/3 DIN B 3σ = 0.10+0.0017It 0 100 C 3σ = 0.15+0.0020ItI -50...0 / 100...250 C 3σ = 0.30+0.0050ItI 250 400 C (± 3σ = rnge including 99.7% of the redings, ( t = bsolute vlue of the temperture in C) Grfic_g_gd_05_en_01 Endress+Huser 3
omnigrd S TR 88 Probe mximum error (type WW) cl. A 3σ = 0.15+0.0020ItI cl. 1/3 DIN B 3σ = 0.10+0.0017It 3σ = 0.15+0.0020ItI -200 600 C -50 250 C -200...-50 / 250 600 C Trnsmitter mximum error See the corresponding documenttion (codes re shown t the end of this document). Grfic_g_gd_05_en_14_A Disply mximum error 0.1% FSR + 1 digit (FSR = Full Scle Rnge) The "4 wires" configurtion, provided s stndrd connection for single Pt 100, excludes dditionl errors in every condition (e.g. deep immersion lengths, long connection cbles without hed trnsmitter,...). Generlly speking, in the "4 wires" configurtion there is higher gurntee of ccurcy. The "2-wire" connection, used in the version of the ATEX certified insert, my crete n dditionl error due to the resistnce of the copper conductors of the minerl insulted cble; such resistnce is dded to the vlue of the Pt 100. The incidence of this source of inccurcy increses with the increse of the insertion length. Mesurement rnge Type TF -50 400 C Type WW -200...600 C Response time Tests in wter t 0.4 m/s (ccording to DIN EN 60751; 23 to 33 C step chnges), only on thermometer insert: Dimeter of the stem Pt 100 type Response time 3 mm TF / WW 6 mm TF / WW t50 = 2 s t90 = 5 s t50 = 3.5 s t90 = 8 s Insultion Insultion resistnce between the terminls nd probe sheth bove 100 MΩ t 25 C (ccording to DIN EN 60751, test voltge 250 V) bove 10 MΩ t 300 C Self heting Negligible when the E+H itemp trnsmitters re employed. 4 Endress+Huser
omnigrd S TR 88 Instlltion Omnigrd S TR 88 thermometers cn be mounted on thermowells instlled on pipes, tnks or other plnt prts tht my require them. In the cse of ATEX-certified components (trnsmitter, insert), plese refer to the relevnt documenttion (refer to the code t the end of this document). Immersion length my hve n effect on the ccurcy of the mesurement. If the immersion is too low, n error my be generted in the temperture recorded due to the lower temperture of the process fluid ner to the wlls nd het trnsfer, which tkes plce through the sensor stem. The incidence of such n error cn be not negligible if there is big difference between the process temperture nd the mbient temperture. In order to void this source of inccurcy, the thermowell should hve smll dimeter nd the immersion length (L) should be, if possible, t lest 100 mm. In pipes of smll section the xis line of the duct must be reched nd if possible slightly exceeded by the tip of the probe (refer to fig. 2A-2B). Insultion of the outer prt of the sensor reduces the effect produced by low immersion. Another solution my be tilted instlltion (see fig. 2C-2D). L L TR88_g_id_07_XX_01 Fig. 2: Instlltion exmples With regrd to corrosion, it is very importnt to choose the correct bse mteril for the thermowell; Endress+Huser offers wide rnge of thermowells suitble for ll kinds of pplictions. For further informtion on specific pplictions, plese contct the E+H Customer Service Deprtment. In the cse tht the sensor components re disssembled, in the following ressembly procedure the definite torques must be employed. This will ssure the housings with the IP grde protection defined. When the surrounding environment hs high humidity rte nd the process is t low temperture, plstic housing is recommended (i.e. model TA20B) to void problems due to condenstion. In the cse of vibrtions the thin film sensing element (TF) my offer dvntges, but the behviour depends on the intensity, the direction nd the dominting frequency in the vibrtion mode. The wire wound Pt 100 (WW), besides hving lrger mesurement nd ccurcy rnge, gurntees greter long term stbility. Upon request, the Customer Service of E+H cn verify through clcultion the resistnce of thermowells t specific operting conditions (pressure, temperture, fluid velocity) tking into ccount lso the forces nd vibrtions generted by the flow. Endress+Huser 5
omnigrd S TR 88 System components Housing The housing, which contins the electric terminls or the trnsmitter, is vilble in different types nd mterils, e.g. plstic, pinted luminium lloy nd stinless steel. The coupling method with the rest of the probe nd the glnd for the cble entry ensures minimum IP65 grde (refer lso to fig. 3). All vilble heds hve internl geometry ccording to DIN 43729 stndrd (form B), nd thermometer connection M24x1.5. Hed type TA20A is the bsic E+H luminium housing for temperture sensors. It is supplied in the E+H corporte colours, without ny extr chrge. Hed TA20B is blck polymide housing, sometimes referred to s the BBK in the Temperture mrket. A screw cp is employed in TA21E nd is joined to the hed body by chin. The TA20D hed (luminium), lso referred to s BUZH, is ble to contin bord nd trnsmitter or two trnsmitters t the sme time. The order of the double trnsmitter must be crried out by choosing the option "flying wires" in the sles structure, nd two trnsmitters in seprte position (THT1, see the tble t the end of the document). The TA20J hed is stinless steel housing used in other instruments mde by E+H nd cn be provided with LCD disply (4 digits), which opertes with 4 20 ma trnsmitters. The TA20R is normlly recommended by the Temperture division of E+H for hygienic pplictions. The TA20W (BUS type) is round blue/grey coloured hed mde of luminium, with clip for the cp closure. The cble glnd M20x1.5 provided with the housings, is comptible with cbles of dimeter between 5 nd 9 mm. Housing type IP Housing type IP Housing type IP Housing type IP TA20A 66 67 110 80 TA20A_g_dd_00_xx_01 TA20B 65 TA20R 66 67 72 120 TA20B_g_dd_00_xx_01 TA20R_g_dd_00_xx_01 TA20W 66 85 140 TA20W_g_dd_00_xx_01 TA20J 66 108 67 98 TA20J_g_dd_00_xx_01 TA20J (disply) 66 108 67 119 TA20J_g_dd_00_xx_02 TA20D 66 TA21E 65 113 140 TA20D_g_dd_00_xx_01 95 Ø 80 TA21E_g_dd_00_xx_01 Fig. 3: Housings nd reltive IP grde Hed trnsmitter The hed-mounted trnsmitters vilble re (lso refer to the "Electronics" section): TMT 180 PCP 4 20 ma TMT 181 PCP 4 20 ma TMT 182 Smrt HART TMT 184 PROFIBUS-PA. The TMT 180 nd the TMT 181 (see fig. 4) re PC progrmmble trnsmitters. The TMT 180 is lso vilble in version with enhnced ccurcy (0.1 C vs. 0.2 C) in the temperture rnge -50 250 C, nd in version with fixed mesurement rnge (specified by the customer in the order phse). The TMT 182 output consists of 4 20 ma nd HART superimposed signls. For the TMT 184 (see fig. 5), with PROFIBUS-PA output signl, the communiction ddress my be set vi softwre or vi mechnicl dip-switch. The customer my specify the configurtion desired during the order phse. 6 Endress+Huser
omnigrd S TR 88 Ø33 Ø44 1 Ø 4.5 + - 2 Ø 6.5 Ø33 6 5 + - 4 3 Ø44 22.5 TMT181_g_gd_06_IT_02 Fig. 4: TMT 180-181-182 Ø 33 Ø44 1 Ø 4.5 + - 2 Ø33 1 8 6 5 + - 4 3 Ø 6.5 Ø44 26.8 TMT184_g_gd_06_IT_01 Fig. 5: TMT 184 Extension neck The extension neck is the prt between the thermowell nd the hed. It is constituted by n 11 mm tube in SS 316L/1.4404 (fig. 6), whose stndrd length (E) cn be chosen mong the following vlues: 80 mm 100 mm 155 mm (normlly used for length L = 110 mm of thermowells DIN 43772 Form 4) 165 mm (normlly used for other lengths of thermowells DIN 43772 Form 4/4F) 200 mm. Other sizes re vilble on request. The connection situted in the upper prt of the neck llows for orienttion of the sensor hed. As illustrted by the chrt in figure 7, the length of the extension neck my influence the temperture in the hed. It is necessry tht this temperture is kept within the limit vlues defined in the prgrph "Operting conditions". SW.24 M24x1.5 5 Ø22 E 22 14 Ø11 Ø11 Ø11 Ø11 25 15 G½ SW. 27 ½ NPT SW. 22 8 30 M14x1.5 SW.17 12 20 M18x1.5 SW.24 TR88nk_G_dd_15_xx_01 Fig. 6: Extension neck in different versions Endress+Huser 7
omnigrd S TR 88 C 30 25 20 15 Hed heting 10 5 0 75 Process temperture 100 125 150 175 200 225 250 Neck extension length mm 570 C 400 C 220 C Grfic_g_gd_05_en_12 Fig. 7: Grph showing the heting of the hed cused by the process temperture Thermowell connection Probe Avilble in stndrd versions: M14 x 1.5 (normlly used for thermowells DIN 43772 Form 4/4F with dimeter of 18 mm) M18 x 1.5 (normlly used for thermowells DIN 43772 Form 4/4F with dimeter of 24 mm) G 1/2 B ISO 228-1 1/2 NPT ANSI B2.1. Other versions my be supplied upon request. Figure 6 shows the bsic dimensions of the threded connections vilble from the sles structure (see prgrph "Ordering informtion" t the end of this document). In the TR 88 the mesuring probe is mde up of minerl (MgO) insulted insert positioned inside the thermowell. The insert length is vilble in the stndrd dimensions DIN 43772 nd in the most commonly used ones, or it cn be personlized by the customer within rnge of vlues (refer to "Sles Structure" t the end of the document). The immersion length (ML) must be chosen in complince with the totl length of thermowell (A) nd of the type of thermowell used; see the following tble (vlid for thermowell bse with stndrd thickness): Type of thermowell ML Type of thermowell ML Type of thermowell ML TA 535 ML = A TW 15 ML = A (L) TA 570 ML = A - 3 TA 540 ML = A - 2 TA 560 ML = A - 3 TA 571 ML = A - 3 TA 550 ML = A - 3 TA 562 ML = A - 3 TA 572 ML = A - 3 TA 555 ML = A - 2 TA 565 ML = A - 3 TA 575 ML = A - 3 TA 557 ML = A - 2 TA 566 ML = A - 3 TA 576 ML = A - 2 For thermowells with non stndrd end thickness (D), use the following formul: ML = A - D + 3. For replcement, the length of the insert (IL) must be chosen using the formul: IL = ML + E + 10. 8 Endress+Huser
6 3 omnigrd S TR 88 - + Red Red 1 + - 2 White White 5 4 Ø42 Ø44 Ø33 Ø33 75 A NPT ML E 10 GAS M4x1 M4x1 Ø6 10 Ø33 Ø42 Ø6 Ø3 TTR88_g_dd_07_en_01 Fig. 8: Functionl components Although the wiring digrm of single Pt 100s is lwys supplied with 4 wires configurtion, the connection of trsmitter cn be executed with 3 wires s well, by voiding to connect whichever of the terminls. The configurtion Pt 100 double with 2 wires (clss B) is only vilble for the ATEX certified inserts. The use of stndrd dimensions (extension neck nd length of immersion) llows for the use inserts on sensors of different kinds nd gurntees rpid delivery times; this llows our customers to reduce the mount of spre prts to be kept on stock. MORSET_G_GD_07_en_01 Fig. 9: Stndrd electricl digrms (cermic terminl block) Endress+Huser 9
omnigrd S TR 88 Certifictes & pprovls Ex pprovl PED pprovl Mteril certifiction Test report nd clibrtion ATEX Certificte KEMA 01 ATEX1169 X (1 GD or 1/2 GD IIC EEx i T6...T1 T85...450 C). The Pressure Equipment Directive (97/23/CE) is respected. As prgrph 2.1 of rticle 1 is not pplicble to these types of instruments, the CE mrk is not requested for the TR 88 destined for generl use. Mteril certifictions cn be requested seprtely. With regrds to the tests nd clibrtion, the "Inspection Report" consists of complince declrtion for the essentil points of the stndrd DIN EN 60751. The "Fctory clibrtion" is crried out in n uthorised lbortory EA (Europen Accredittion) of E+H ccording to n internl procedure. A clibrtion my be requested seprtely ccording to n ccredited procedure EA (SIT clibrtion). Clibrtion is crried out on the thermometer insert. Further detils Mintennce Delivery time The Omnigrd S thermometers do not require ny specific mintennce. In cse of ATEX certified components (trnsmitter, insert), plese refer to the relevnt specific documenttion (see the code t the end of this document). For smll quntities (pproximtely 10 units) nd stndrd options, between 5 nd 15 dys depending on the configurtion required. 10 Endress+Huser
omnigrd S TR 88 Ordering informtion Sles structure TR88- Sfety (Ex) certifiction A B E Ex certifiction not required ATEX II 1 GD EEx i IIC certified ATEX II 1/2 GD EEx i IIC certified Hed mteril, conduit, IP grde A TA20A Aluminium, conduit M20x1.5, IP66/IP67 4 TA20A Aluminium, PROFIBUS connector, IP66 2 TA20A Aluminium, conduit 1/2 NPT, IP66/IP67 7 TA20B Polymide, blck, conduit M20x1.5, IP65 E TA21E Aluminium, screw cp, M20x1.5, IP65 6 TA20D Aluminium, high lid, conduit M20x1.5, IP66 5 TA20D Aluminium, high lid, PROFIBUS connector, IP66 8 TA20D Aluminium, high lid, conduit 1/2 NPT, IP66 J TA20J SS 316L, conduit M20x1.5, IP66/IP67 K TA20J SS 316L, with disply, conduit M20x1.5, IP66/IP67 M TA20J SS 316L, PROFIBUS connector, IP66 R TA20R SS 316L, screw cp, conduit M20x1.5, IP66/IP67 S TA20R SS 316L, screw cp, PROFIBUS connector, IP66 W TA20W Aluminium, round lid, clip, conduit M20x1.5, IP66 Y Specil version Length of extension neck E (45-300 mm); mteril SS 316L/1.4404 1 80 mm, extension E 2 100 mm, extension E 3 155 mm, extension E (DIN43772 only ML=110) 4 165 mm, extension E (DIN43772) 5 200 mm, extension E 8... mm, extension E to specify 9... mm, specil extension E Thermowell connection A M14x1.5 DIN 43772 B M18x1.5 DIN 43772 C G1/2 B ISO 228-1 E 1/2 NPT ANSI B2.1 Y Specil version Dimeter nd mteril of extension neck E 1 D1=11 mm, SS 316Ti/1.4571 9 Specil version Insertion length ML (50-2000 mm) A 110 mm Insertion length ML B 140 mm Insertion length ML C 170 mm Insertion length ML D 200 mm Insertion length ML E 260 mm Insertion length ML F 410 mm Insertion length ML X... mm Length ML to specify Y... mm Specil ML length Insert dimeter 1 Dimeter 3 mm, SS 316L/1.4404 2 Dimeter 6 mm, SS 316L/1.4404 Terminl type or built-in trsmitter F Flying leds C Cermic terminl block 2 TMT180-A22, fixed rnge, from...to... C, ccurcy 0.2 K, spn -50...650 C 3 TMT180-A11, fixed rnge, from...to... C, ccurcy 0.1 K, spn -50... 250 C 4 TMT180-A11 configurble rnge, from...to... C, ccurcy 0.2 K, spn -200...650 C 5 TMT180-A12 configurble rnge, from...to... C, ccurcy 0.1 K, spn -50...250 C P TMT181-A insulted, 2-wire PCP trnsmitter configured from...to... C Q TMT181-B isolted, 2-wire PCP ATEX trnsmitter, configured from...to... C T HART ATEX trnsmitter 2-wire TMT182-B, isolted, configured from...to... C S PROFIBUS-PA trnsmitter 2-wire TMT184-A, configured from...to... C V PROFIBUS-PA ATEX trnsmitter 2-wire TMT184-B, configured from...to... C Endress+Huser 11
omnigrd S TR 88 RTD type, temperture rnge, wiring digrm 3 1 Pt 100, TF Clss A, -50/400 C 4 wires 7 1 Pt 100, TF Clss 1/3 DIN B -50/400 C 4 wires B 2 Pt 100, WW Clss A, -200/600 C 3 wires C 1 Pt 100, WW Clss A, -200/600 C 4 wires D 2 Pt 100, WW Clss B, -200/600 C 2 wires F 2 Pt 100, WW Clss 1/3 DIN B -200/600 C 3 wires G 1 Pt 100, WW Clss 1/3 DIN B -200/600 C 4 wires Y Specil version Mteril certifiction 0 Mteril certifiction not requested 9 Specil version Test nd clibrtion on the insert 0 Test nd clibrtion not requested 1 Inspection report on sensor 2 Inspection report on loop A Fctory clibrtion, single RTD, 0-100 C B Fctory clibrtion, single RTD, loop, 0-100 C C Fctory clibrtion, double RTD, 0-100 C E Fctory clibrtion, single RTD, 0-100-150 C F Fctory clibrtion, single RTD, loop, 0-100-150 C G Fctory clibrtion, double RTD, 0-100-150 C Additionl options 0 Additionl options not required 9 Specil version Mrking 0 Tgging ccording to customer specifictions TR88- Complete order code 12 Endress+Huser
omnigrd S TR 88 Sles structure THT1 Model nd version of the hed trnsmitter A11 A12 A13 A14 A15 A16 A17 A18 A19 A20 F11 F21 F22 F23 L11 L21 L22 L23 K11 K21 K23 K24 YYY TMT180-A11 progrmmble from...to... C, ccurcy 0.2 K, spn limit -200...650 C TMT180-A12 progrmmble from...to... C, ccurcy 0.1 K, spn limit -50...250 C TMT180-A21AA fixed rnge, ccurcy 0.2 K, spn 0...50 C TMT180-A21AB fixed rnge, ccurcy 0.2 K, spn 0...100 C TMT180-A21AC fixed rnge, ccurcy 0.2 K, spn 0...150 C TMT180-A21AD fixed rnge, ccurcy 0.2 K, spn 0...250 C TMT180-A22AA fixed rnge, ccurcy 0.1 K, spn 0...50 C TMT180-A22AB fixed rnge, ccurcy 0.1 K, spn 0...100 C TMT180-A22AC fixed rnge, ccurcy 0.1 K, spn 0...150 C TMT180-A22AD fixed rnge, ccurcy 0.1 K, spn 0...250 C TMT181-A PCP, 2-wire, isolted, progrmmble from...to... C TMT181-B PCP ATEX, 2-wire, isolted, progrmmble from...to... C TMT181-C PCP FM IS, 2-wire, isolted, progrmmble from...to... C TMT181-D PCP CSA, 2-wire, isolted, progrmmble from...to... C TMT182-A HART, 2-wire, isolted, progrmmble from...to... C TMT182-B HART ATEX, 2-wire, isolted, progrmmble from...to... C TMT182-C HART FM IS, 2-wire, isolted, progrmmble from...to... C TMT182-D HART CSA, 2-wire, isolted, progrmmble from...to... C TMT184-A PROFIBUS-PA, 2-wire, progrmmble from...to... C TMT184-B PROFIBUS-PA ATEX, 2-wire, progrmmble from...to... C TMT184-C PROFIBUS-PA FM IS, 2-wire, progrmmble from...to... C TMT184-D PROFIBUS-PA CSA, 2-wire, progrmmble from...to... C Specil trnsmitter Appliction nd services 1 Assembled into position 9 Specil version THT1- Complete order code Endress+Huser 13
Supplementry documenttion RTD Thermometers Omnigrd TST - Generl informtion Industril protecting tubes - Omnigrd TA series Terminl housings - Omnigrd TA 20 Temperture hed trnsmitter itemp Pt TMT 180 Temperture hed trnsmitter itemp PCP TMT 181 Temperture hed trnsmitter itemp HART TMT 182 Temperture hed trnsmitter itemp PA TMT 184 Pt 100 insert - Omniset TPR 100 Thermowell for temperture sensor - Omnigrd M TW 15 Sfety instructions for use in hzrdous res E+H Thermolb - clibrtion certifictes for industril thermoelements nd working stndrds. RTD s nd thermocouples TI 088T/02/en TI138T/02/en TI 072T/02/en TI 088R/09/en TI 070R/09/en TI 078R/09/en TI 079R/09/en TI 268T/02/en TI 265T/02/en XA 003T/02/z1 TI 236T/02/en Subject to modifiction Endress+Huser Gmbh+Co. KG Instruments Interntionl P.O. Box 2222 Colmrer Str. 6 D-79574 Weil m Rhein Germny Tel. +49 7621 97502 Fx +49 7621 975345 http://www.endress.com info@ii.endress.com TI 271T/02/en/11.03 60021058 FM+SGML 6.0