Automotive Data Solutions Inc. INSTALL GUIDE ADS-AL(DL)-CH CH Available for : ADS-AL CA Rev. Date: May 0, 0 Doc. No.: ##50## 0059 Version FRançaise disponible en ligne au www.idatalink.com please visit www.idatalink.com/support for complete product details The brand names and logos found in this guide are property of their respective owners. Automotive Data Solutions Inc. 0 NOTICE: The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. This guide has been written for properly trained technicians; a certain level of skill & knowledge is therefore assumed. Please review the Installation Guide carefully before beginning any work.
Page of 9 ADS-AL(DL)-CH Doc. No.: ##50## 0059 install type SeLeCtiOn FEATURES MAKE MODEL YEAR VOLKSWAGEN JEEP DODGE CHRYSLER INSTALL TYPE DATA IMMOBILIZER BYPASS DOWNLOADABLE SOFTWARE RS COMMUNICATION -WAY COMPATIBILITY PRIORITY UNLOCK DOOR LOCK DOOR UNLOCK ARM OEM ALARM DISARM OEM ALARM TRUNK/HATCH RELEASE POWER LIFTGATE POWER SLIDING DOOR (L) POWER SLIDING DOOR (R) DOOR STAT OUTPUT TRUNK STAT OUTPUT RAP SHUTDOWN CTRL BRAKE PEDAL STAT OUTPUT E-BRAKE OUTPUT TACHOMETER OUTPUT DATA/MUX IGNITION CTRL SECURE TAKEOVER PARKING LIGHT CTRL 00 08- or 00 Limited 08- or 00c 08- or 00c SRT8 08- or Town & Country 08- or Caravan 08-0 or Challenger SXT 08- or Challenger R/T 08- or Challenger SRT8 08- or Charger SE 08- or Charger R/T 08- or Charger SRT8 08- or Durango or Grand Caravan 08- or Journey 09- or Magnum 08 or RAM 500 09- or RAM 500 or RAM 500 or Commander 08-0 or Grand Cherokee 08- or Routan 09- or Visit our website for advanced features.
Page of 9 ADS-AL(DL)-CH Doc. No.: ##50## 0059 REFER TO ADS-HRN CHTIP* ASSEMBLY FOR PROPER CONNECTIONS AND MATCH EACH LETTER ACCORDINGLY GWR (-) INPUT - BLUE/WHITE (NC) WHITE (NC) BLACK (NC) RED LOCK/ARM (-) INPUT - GREEN/BLACK UNLOCK/DISARM (-) INPUT - BLUE/BLACK TRUNK (-) INPUT - RED/WHITE DISARM ONLY (-) INPUT - BROWN LEFT SLIDING DOOR (-) INPUT - PURPLE/YELLOW RIGHT SLIDING DOOR (-) INPUT - PURPLE/BLACK PARKING (+) INPUT - WHITE STARTER (+) INPUT - BLACK/WHITE *E-BRAKE (-) OUTPUT - GREEN *TACH (AC) OUTPUT - PURPLE/WHITE THE BRAKE STATUS IS FUNCTIONAL ONLY WHEN THE IGNITION IS POWERED VEHICLE (-) DRIVER DOOR PIN CONNECT EITHER IDATALINK OR STANDARD WIRING IDATALINK (RS) PORT REQUIRED ON REMOTE STARTER. IF UNAVAILABLE USE STANDARD WIRING METHOD IDATALINK LEGEND Wiring connections not required when installed in idatalink mode * Wiring connection not required in -way idatalink type - wiring diagram ONLY WHEN RAP SHUTDOWN IS REQUIRED TACH (AC) INPUT E-BRAKE (-) INPUT STARTER (+) OUTPUT PARKING (+) OUTPUT RIGHT SLIDING DOOR (-) OUTPUT LEFT SLIDING DOOR (-) OUTPUT DISARM ONLY (-) OUTPUT TRUNK (-) OUTPUT UNLOCK (-) OUTPUT LOCK (-) OUTPUT GROUND WHEN RUNNING (-) OUTPUT E D REARM (-) OUTPUT IDATALINK REMOTE STARTER OPTIONAL -> PARKLIGHTS (+) OUTPUT OPTIONAL -> TRUNK STATUS (-) INPUT OPTIONAL -> DOOR STATUS (-) INPUT A IF YOUR MODULE HARDWARE IS VERSION. OR NEWER YOU CAN ELIMINATE THE RELAY AND CONNECT THE YELLOW DIRECTLY TO THE VEHICLE. THE DIODE IS ONLY REQUIRED FOR THE ADS-HRN CH ASSEMBLY THE DIODE IS NOT REQUIRED FOR THE ADS-HRN CHTIP ASSEMBLY IGNITION OUTPUT - PINK GROUND INPUT - BLACK V INPUT - RED/WHITE BRAKE INPUT - ORANGE DO NOT USE THE RED/WHITE IF YOU ARE PLANNING TO POWER THE VEHICLE POSITIVE PARKLIGHTS. YELLOW/BLACK - DOOR STATUS (-) OUTPUT* YELLOW/RED - TRUNK STATUS (-) OUTPUT* YELLOW - MULTIPLEX PARKLIGHTS OUTPUT B C DIODE N00 G 85 87A 87 0 USE THIS OUTPUT ONLY ON VEHICLES EQUIPPED WITH MUX PARKING LIGHTS CONTROL 86 F VEHICULE PARKLIGHTS MUX ADS-HRN CHTIP ASSEMBLY - SOLD SEPARATELY ADS-HRN CH ASSEMBLY - SOLD SEPARATELY E D A B C VEHICLE HARNESS OR F E D A B C VEHICLE HARNESS F G G
Page of 9 ADS-AL(DL)-CH Doc. No.: ##50## 0059 type - wire CrOSS reference CHart CAN HIGH CAN LOW LEFT FRONT DOOR PARKING LIGHT IGNITION MAKE MODEL YEAR POSITION VOLKSWAGEN JEEP DODGE CHRYSLER LOCATION POSITION LOCATION LOCATION POLARITY LOCATION POSITION 00 08-5 White/Black A 6 White/LtBlue A Violet B White/Brown MUX E Pink/White 00 Limited 08-5 White/Black A 6 White/LtBlue A Violet B White/Brown MUX E Pink/White 00c 08-5 White/Black A 6 White/LtBlue A Violet B White/Brown MUX E Pink/White 00c SRT8 08-5 White/Black A 6 White/LtBlue A Violet B White/Brown MUX E Pink/White Town & Country 08-5 White/LtBlue A 6 White/Brown A Violet C White/Brown MUX F Pink/White Caravan 08-0 5 White/LtBlue A 6 White/Brown A Violet C White/Brown MUX F Pink/White Challenger SXT 08-5 White/Black A 6 White/LtBlue A Violet C White/Brown MUX F Pink/White Challenger R/T 08-5 White/Black A 6 White/LtBlue A Violet C White/Brown MUX F Pink/White Challenger SRT8 08-5 White/Black A 6 White/LtBlue A Violet C White/Brown MUX F Pink/White Charger SE 08-5 White/Black A 6 White/LtBlue A Violet B White/Brown MUX E Pink/White Charger R/T 08-5 White/Black A 6 White/LtBlue A Violet B White/Brown MUX E Pink/White Charger SRT8 08-5 White/Black A 6 White/LtBlue A Violet B White/Brown MUX E Pink/White Durango 5 White/LtGreen A 6 White/LtBlue A Violet/Gray C White MUX F Pink/White Grand Caravan 08-0 5 White/LtBlue A 6 White/Brown A Violet C White/Brown MUX F Pink/White Grand Caravan 5 White/LtBlue A 6 White/Brown A Violet C White/Green MUX F Pink/White Journey 09-5 White/LtBlue A 6 White/Brown A Violet C White/Violet (+) H Pink/White Magnum 08 5 White/Black A 6 White/LtBlue A Violet B White/Brown MUX F Pink/White RAM 500 09-5 White/LtGreen A 6 White/LtBlue A Violet/Gray C White MUX F Pink/White RAM 500 5 White/LtGreen A 6 White/LtBlue A Violet/Gray C White MUX F Pink/White RAM 500 5 White/LtGreen A 6 White/LtBlue A Violet/Gray C White MUX F Pink/White Commander 08-0 5 White/LtGreen A 6 White/LtBlue A Violet D N/A (-) G Pink/White Grand Cherokee 08-5 White/LtGreen A 6 White/LtBlue A Violet D N/A (-) G Pink/White Routan 09-5 White/LtBlue A 6 White/Brown A Violet C White/Brown MUX F Pink/White A B C D E F G H *LEGEND - COMPONENT LOCATOR At -pin node Black connector at drivers kick panel At drivers kick panel Left door At switch or drivers kick panel At switch At pin of relay 7 in IPM At passengers kick panel
Page 5 of 9 ADS-AL(DL)-CH Doc. No.: ##50## 0059 type - wiring diagram ONLY WHEN RAP SHUTDOWN IS REQUIRED USE THIS OUTPUT ONLY ON VEHICLES EQUIPPED WITH MUX PARKLIGHTS CONTROL TACH (AC) INPUT E-BRAKE (-) INPUT STARTER (+) OUTPUT PARKING (+) OUTPUT RIGHT SLIDING DOOR (-) OUTPUT LEFT SLIDING DOOR (-) OUTPUT DISARM (+) OUTPUT TRUNK (-) OUTPUT UNLOCK (-) OUTPUT LOCK (-) OUTPUT V(+) GROUND (-) GROUND WHEN RUNNING (-) OUTPUT REMOTE STARTER VEHICLE (-) DRIVER DOOR PIN REQUIRED -> REARM (-) OUTPUT REQUIRED -> PARKLIGHTS (+) OUTPUT REQUIRED -> ST IGNITION (+) INPUT REQUIRED -> BRAKE (+) INPUT OPTIONAL -> TRUNK STATUS (-) INPUT OPTIONAL -> DOOR STATUS (-) INPUT VEHICULE PARKLIGHTS MUX IF YOUR MODULE HARDWARE IS VERSION. OR NEWER YOU CAN ELIMINATE THE RELAY AND CONNECT THE YELLOW DIRECTLY TO THE VEHICLE 5 AMPS 85 87 87A 0 86 IDATALINK CONNECT EITHER IDATALINK OR STANDARD WIRING IDATALINK (RS) PORT REQUIRED ON REMOTE STARTER. IF UNAVAILABLE USE STANDARD WIRING METHOD REMOTE STARTER START OUTPUT MUST BE EXTENDED TO ITS MAXIMUM WHEN USING TACHLESS MODE (CRANK TIME: AT LEAST.5 SECONDS) OR USE TACH CONNECTION INSTEAD N00 DIODE IDATALINK GWR (-) INPUT - BLUE/WHITE (NC) WHITE GROUND - BLACK V - RED LOCK/ARM (-) INPUT - GREEN/BLACK UNLOCK/DISARM (-) INPUT - BLUE/BLACK TRUNK (-) INPUT - RED/WHITE DISARM ONLY (-) INPUT - BROWN LEFT SLIDING DOOR (-) INPUT - PURPLE/YELLOW RIGHT SLIDING DOOR (-) INPUT - PURPLE/BLACK PARKING (+) INPUT - WHITE STARTER (+) INPUT - BLACK/WHITE *E-BRAKE (-) OUTPUT - GREEN *TACH (AC) OUTPUT - PURPLE/WHITE LEGEND Wiring connections not required when installed in idatalink mode * Wiring connection not required in -way idatalink WHITE/BLACK - IGNITION (+) VEHICLE SIDE WHITE/RED - IGNITION (+) CONNECTOR SIDE WHITE YELLOW/BLACK - DOOR STATUS (-) OUTPUT* YELLOW/RED - TRUNK STATUS (-) OUTPUT* YELLOW - MULTIPLEX PARKLIGHTS OUTPUT BROWN/RED - CANH BROWN/YELLOW-CANL ORANGE/BLACK (NC) ORANGE/WHITE (NC) ORANGE - BRAKE STATUS (+) OUTPUT* PINK/BLACK (NC) PINK - IGNITION (+) INPUT VEHICLE SIDE BLUE/RED (NC) BLUE/YELLOW (NC) GREEN/RED (NC) GREEN/YELLOW (NC) GRAY/RED - IGNITION (+) INPUT FROM KEY GRAY/YELLOW (NC) FOR SECURE TAKE OVER, CONNECT THE BRAKE STATUS TO THE REMOTE STARTER. DO NOT CONNECT TO THE VEHICLE BRAKE, IT VOIDS THE SECURE TAKE OVER FEATURE. THE BRAKE STATUS IS FUNCTIONAL ONLY WHEN THE IGNITION IS POWERED. IGNITION PINK/WHITE CAN HIGH CAN LOW 5 6 7 8 9 0
Page 6 of 9 ADS-AL(DL)-CH Doc. No.: ##50## 0059 installation mode SeLeCtiOn Press and release programming button to select installation mode. LED flashes (X) once = DATA MODE LED flashes (X) twice = STANDARD HARD MODE Press and hold programming button until LED turns solid GREEN to register selection. After registration, follow Factory Reset Procedure to change installation mode and restart this procedure. module PrOgramming PrOCedUre Close driver door. 6 OFF Turn key to OFF position. Re-open driver door to wake up data bus. 7 Remove key. Insert key into ignition. 8 UNLOCK Press UNLOCK on the OEM remote. ON Turn key to ON position. If vehicle is not equipped with OEM remote, press module programming button. LED will turn solid RED. 9 Wait, LED will turn solid GREEN for seconds. 5 Within 5 seconds, LED will flash GREEN rapidly. 0 Module Programming Procedure completed.
Page 7 of 9 ADS-AL(DL)-CH Doc. No.: ##50## 0059 module PrOgramming installation PrOCedUre mode SeLeCtiOn - PUSH to Start Press Close driver and release door. programming button to select installation mode. LED flashes (X) once = DATA Re-open MODE driver door to wake up LED flashes (X) twice = STANDARD data bus. HARD MODE x DO NOT PRESS BRAKE PEDAL Push start button twice [x] to ON position. LED will turn solid RED. 5 6 7 Press DO NOT and PRESS hold BRAKE PEDAL programming button until Push LED start turns button solid once GREEN [x] to to OFF register position. selection. After registration, follow Factory Press UNLOCK Reset Procedure on the OEM to change installation mode and remote. restart this procedure. UNLOCK x If vehicle is not equipped with OEM remote, press module programming button. Wait, LED will turn solid GREEN for seconds. Within 5 seconds, LED will flash GREEN rapidly. 8 Module Programming Procedure completed.
Page 8 of 9 ADS-AL(DL)-CH Doc. No.: ##50## 0059 identify VeHiCLe year Locate the Vehicle Identification Number (VIN) and identify the 0th character. A 5 Y N 5 T A L 8 D 5 R 0 X Match the VIN s 0th character to its corresponding year. L > 990 S > 995 Y > 000 5 > 005 A > 00 M > 99 T > 996 > 00 6 > 006 B > 0 N > 99 V > 997 > 00 7 > 007 C > 0 P > 99 W > 998 > 00 8 > 008 D > 0 R > 99 X > 999 > 00 9 > 009 E > 0 LED STATUS Flashing RED DIAGNOSTICS DURING PROGRAMMING DURING REMOTE START WITH IGNITION OFF Missing/wrong information from firmware or vehicle Incorrectly programmed Solid RED Waiting for more vehicle information Incorrectly programmed Flashing GREEN Additional steps required to complete programming module diagnostics Correctly programmed and operational Incorrectly programmed or connected Not programmed waiting for more vehicle information False ground when running status from remote starter Solid GREEN then OFF Correctly programmed Reset in progress Reset in progress OFF No activity or already programmed Invalid ground when running status from remote starter At rest and ready for a remote start sequence FaCtOry reset PrOCedUre DISCONNECT all connectors from module EXCEPT the black -PIN standard or optional data connector. DISCONNECT black -PIN standard or optional data connector. 5 6 LED will turn solid red for seconds. RESET COMPLETED. RECONNECT all connectors. PRESS AND HOLD programming button while connecting either -PIN standard or optional data connector. When LED flashes red, RELEASE programming button. 7 Repeat programming procedure. Failure to follow procedure may result with a DTC or a CHECK ENGINE error message.
Page 9 of 9 ADS-AL(DL)-CH Doc. No.: ##50## 0059 warning: read BeFOre remote Starting the VeHiCLe IMPORTANT I All vehicle doors must be closed and locked prior to remote start sequence. Failure to comply will result in remote starter malfunction. take OVer PrOCedUre - to the VeHiCLe Owner NOTE I All vehicle doors must be closed and locked prior to remote start sequence. Insert key into ignition. TIME RESTRICTIN COMING UP ON Turn key to ON position. Wait seconds for key validation. Press UNLOCK on after-market remote. 5 Press and release BRAKE pedal. TIME RESTRICTIN Within 5 SECONDS from previous step: Open vehicle door. Enter vehicle. 6 Take over procedure completed. Failure to follow procedure within time restriction will result in vehicle engine shutdown. take OVer PrOCedUre - PUSH to Start - to the VeHiCLe Owner NOTE I All vehicle doors must be closed and locked prior to remote start sequence. x DO NOT PRESS BRAKE PEDAL Push start button twice [x] to ON position. TIME RESTRICTIN COMING UP Press UNLOCK on after-market remote. TIME RESTRICTIN Within 5 SECONDS from previous step: Open vehicle door. Enter vehicle. 5 Wait seconds for key validation. Press and release BRAKE pedal. Take over procedure completed. Failure to follow procedure within time restriction will result in vehicle engine shutdown.