PRO-SPEC IV SYNTHETIC BLEND

PRO-SPEC IV SYNTHETIC BLEND

89 Years of world-class manufacturing experience has enabled Texas Refinery Corp. to develop the most robust Total Base Number in the industry, miles ahead of other CJ-4 oils on the market... introducing PRO-SPEC IV SYNTHETIC BLEND with a 14 TBN! This new, ground-breaking technology formulated into PRO-SPEC IV SYNTHETIC BLEND provides you with one engine oil to protect on-highway low emission diesel engines with after treatment devices, pre-2007 diesel engines, as well as off-road engines operating on 500 ppm sulfur diesel fuel and Tier 4 off-road diesel engines. PRO-SPEC IV SYNTHETIC BLEND is a new generation engine oil that provides emission system durability, prevents catalyst poisoning and particulate filter blocking, while at the same time controls soot thickening, oil consumption and wear prevalent in EGR engines. Low sulfur diesel (15ppm) used in on-highway engines has led many in the industry to believe TBN is not as important as it was before, due to less sulfur in the fuel. But with increased exhaust gases that are circulated back into the engine, Texas Refinery Corp. believes the TBN, and more importantly TBN retention, is just as critical due to the increase of acidity in the EGR process. The 14 TBN formulated in PRO-SPEC IV SYNTHETIC BLEND is The Right Choice, because let s face it... when your equipment is down, so is your cash flow. ~ 2 ~

Controlling Corrosive Bearing Wear Enables You To Run Extended Drain Intervals With Pro-Spec IV The MACK T-12 : A New Engine Test, 300 hours in length, used to measure the ability of an oil to protect against cylinder wear, soot thickening, bearing corrosion and oxidation at high operating temperatures and high EGR rates. Competitive CJ-4 Oil PRO-SPEC IV SYNTHETIC BLEND PRO-SPEC IV SYNTHETIC BLEND offers the most advanced protection against corrosive wear in rod bearings ~ 3 ~

PRO-SPEC IV provides oxidation protection not found in other CJ-4 oils... 60% Better Protection The operating conditions of your engine are more extreme than they were in the past, with much higher temperatures placing demands on the oil. As temperatures rise, the process of oxidation can begin to cause problems for you, unless you are using PRO-SPEC IV SYNTHETIC BLEND Engine Oil. Less oxidation means less deposits in your engine, longer drain intervals and more time for your equipment to make money. Oxidation Progression: Darkening of oil Insoluble Sludge Higher peak cylinder temperatures are prevalent in EGR engines, causing the need for improved oxidation resistance in your oil. Corrosive Organic Acids Oil Thickening, Varnish and Gum Deposits on Pistons ~ 4 ~

Exhaust Gas Recirculation engines generate high levels of soot, and if the engine oil doesn t disperse it well, the soot forms a fused mass that leads to abrasive wear, oil consumption and premature engine failure PRO-SPEC IV SYNTHETIC BLEND is formulated with powerful dispersant chemistry to keep soot dispersed into finer particles, which results in reduced oil thickening and improved protection against abrasive wear. PRO-SPEC IV provides wear protection for your engines against high EGR rates and excess soot generation ~ 5 ~

PRO-SPEC IV results in the Caterpillar C-13 Test confirms less deposits formed under the same engine test conditions Other CJ-4 Oil Heavy carbon formation in crown land Carbon Deposits in grooves of piston PRO-SPEC IV SYNTHETIC BLEND Crown Land virtually free from heavy carbon Little to no carbon in grooves of piston PRO-SPEC IV provides excellent engine cleanliness to minimize your oil consumption and protect exhaust after treatment systems. Clean Turbochargers help maintain horse power and can yield better responsiveness and acceleration. ~ 6 ~

All The Benefits of PRO-SPEC IV, PLUS MORE! 0.16 GRAPH 1 MOLY XL PRO-SPEC SYNTHETIC BLEND is the same oil as PRO-SPEC IV, with a unique liquid molybdenum compound added to the formulation for a higher level of anti-wear protection. The moly compound is significant in reducing wear and friction, as seen in the first graph. CO-EFFICIENT OF FRICTION 0.15 0.14 0.13 0.12 0.11 0.10 0.09 0.08 0.07 COMMERCIAL GRADE OIL MOLY XL PRO-SPEC IV 0.06 100 200 300 400 500 600 700 800 LOAD, N GRAPH 2 Temperatures within the newer engines can be a problem for many oils, but the MOLY XL PRO-SPEC IV properties actually become more noticeable as temperatures rise. Graph 2 shows the friction reduction as temperatures continue to rise. This is one reason why many customers notice an improvement in fuel efficiency with MOLY XL PRO-SPEC IV. CO-EFFICIENT OF FRICTION 0.16 0.14 0.12 0.10 0.08 0.06 0.04 0.02 COMMERCIAL GRADE OIL MOLY XL PRO-SPEC IV 0.0 50 70 90 110 130 150 170 TEMPERATURE (C) GRAPH 3 Reduction in wear with MOLY XL PRO-SPEC IV is also shown by running the Four-Ball Wear Test. The higher the load, the better MOLY XL PRO-SPEC IV makes a difference for you. 7.0 6.0 Base Oil 5.0 Pamper your engine with MOLY XL PRO-SPEC IV: Less friction and wear during start-up and operation Wear Ratio 4.0 3.0 EP Regime MOLY XL PRO-SPEC IV Cooler operating temperatures Maximum horsepower 2.0 Antiwear Regime Increased Fuel Economy 1.0 15 30 45 60 75 90 Load - kg ~ 7 ~

Almost a year ago now, we were introduced to your PRO-SPEC SunDevil line of motor oils for gas and Plumbing diesel trucks. By switching to these products, we have cut our costs for motor oils in half. Furthermore, with less downtime for maintenance, we are able to perform this work inhouse much more economically. We are also using the Lab Analysis Program to closely monitor the conditions and performance of our vehicles, something we were never able to do before. We are amazed at how the PRO-SPEC oil stands up to the desert heat and does not break down. KEITH REGIER I have used PRO-SPEC 15W/40 motor oil in my 2001 Peterbilt with a C-15 CAT engine since it was new. I bought this truck in June of 2000, and after 900,000 miles it still runs great. I change the motor oil every 42,000 to 49,000 miles with filter changes about halfway. I ve had two overheads run, the second at 430,000 miles and the mechanic said he has never seen an engine so clean. I told him that it must be the TRC oil. I have been using your MOLY XL PRO-SPEC 15W/40 in our engines for 13 years. I have a 4 cylinder Kubota 14kw generator. It has over 28,000 hours and still keeps on going. In the winter and spring months it runs 24/7. The Kubota needs about two quarts of make-up oil per week. I change the oil and filter between 600 to 700 hours. Western Quality Concrete TRC oils are the ones to use, when you consider your time savings and reduction in oil change frequencies. SPECIFICATIONS Meets and/or exceeds MIL-L-2104E, MIL-L-46152E, CID AA 52039, Caterpillar TO-2, Caterpillar ECF-3, Caterpillar ECF-2, Cummins CES 20077, Cummins CES 20078, Cummins CES 20081, Detroit Diesel Power Guard 93K218, 93K214, Power Guard 93K217, Mack EO-N Premium Plus, Mack EO-N Premium Plus 03, Mack EO-O Premium Plus 07, Navistar, Allis Chalmers, Series 3, GM6094M, Ford M2C153E, M2C171C, M2C171D, ACEA E9/E7/E5/E3/B3/A3, MAN 271, MAN 3275, Mercedes Benz MB 228.31 and MB229.1, MTU Type 1, Type II, Volvo VDS-2, Volvo VDS-3, Volvo VDS-4, Global DHD-1, Chrysler MS-6395-D, Renault RLD-3, JASO DH-2, Allison C4, A.P.I. CF-4, CG-4, CH-4, CI-4, CI-4 Plus, CJ-4, SH, SJ, SL, SM. ASTM TEST METHOD TESTS 15W/40 10W/30 Product Code #6775 #6715 D287 API Gravity 27/29 27/29 D287 Specific Gravity at 60 0 F, Typical.87.86 D-92 Flash Point, 0 F, COC, Minimum 400 0 F. (204 0 C.) 385 0 F. (196 0 C.) D-97 Pour Point, Typical -30 0 F. (-34 0 C.) -35 0 F. (-37 0 C.) D-5293 Viscosity @ -25 0 C, Cold Cranking Simulator cp 7000 max. - - - D-5293 Viscosity @ -30 0 C, Cold Cranking Simulator cp - - - 7000 max. D-4684 Viscosity @ -25 0 C, Mini Rotor Viscosimeter-TP1 cp 25,000 - - - D-4684 Viscosity @ -30 0 C, Mini Rotor Viscosimeter-TP1 cp - - - 21.500 D-446 Viscosity @ 100 0 C, cst, Typical 15.5 12.4 D-446 Viscosity @ 40 0 C, cst, Typical 119.0 82.0 D-2270 Viscosity Index 150 150 D-874 Sulfated Ash, Wt. %, Maximum 0.99% 0.99% D-2896 Total Base Number, mg KOH/g 14 14 D-892 Foam Tendency/Stability: Sequence I 0/0 0/0 Sequence II 0/0 0/0 Sequence III 0/0 0/0 Calcium, Wt. %, Typical 0.13 0.13 Zinc, Wt. %, Typical 0.13 0.13 Nitrogen, Wt. %, Typical 0.23 0.23 Magnesium, Wt. %, Typical 0.09 0.09 Handling Information: For safe handling of the product, read the Safety Data Sheet (SDS). PRO-SPEC is a registered trademark of Texas Refinery Corp. TEXAS REFINERY CORP Fort Worth, Texas Moose Jaw, Saskatchewan Toronto, Ontario Toll Free: 1-800-827-0711 Toll Free Fax: 1-800-582-3329 www.texasrefinery.com E-mail: lube1@texasrefinery.com PRINTED IN U.S.A. 9/2014 L306775