Active Bollards An aesthetic solution to a complex need Crash tested, Ross active bollards are designed to provide temporary or permanent security measures and are built to withstand violent impacts. Despite their inherent strength, the variety of finishes and options allow the bollards to blend seamlessly into their surroundings to minimize their presence.
ROSS PERIMETER SECURITY Active Bollards (XT-1200/XT-1208) K12/L2 and K8 Standard Mount Retractable Bollards............. pg.3 Offering proven anti-ram security, pleasing aesthetics and unrestricted access for pedestrians and bicycles, these bollards are designed for simple maintenance and long service life. (XT-2200) M50 P1 Shallow Mount Retractable Bollard - Heald Raptor............. pg.6 The only bollard of its kind, the Raptor combines a unique retracting motion, a sleek, modern design and easy maintenance all in a shallow-mount installation that s ideal where site conditions prohibit deep excavation. (XT-2300/2400) PAS 68 Surface Mount Sliding Bollards - Heald Matador............. pg.10 A smart choice for both permanent and temporary security applications, the Matador is the only surfacemounted automated bollard, offering many of the same architectural design benefits as retractable bollards, but without the need to excavate and pour a foundation. 1
Industries Applications Government Military Shipping Ground, Sea, Air Critical Infrastructure Oil and Gas Mass Transportation Chemical/Pharmaceutical Banking/Financial Commercial Data Centers Stadiums and Arenas Institutional Industrial The Ross XT-1200/XT-1208 Retractable Bollards provide DOD K12/L2 and DOS K8 crash certified security for controlling vehicle access while allowing pedestrians and bicycles to pass freely. The XT- 1200 series is ideal for a wide variety of pedestrian traffic applications, including stadiums, courthouses, museums, parks, mass transit facilities, universities and corporate offices. The XT-2200 Retractable Bollard (Heald Raptor) provides ASTM F2656-07 M50-P1 and PAS 68 crash tested security and offers a great alternative to both wedge barriers and standard bollards. The Raptor is an ideal choice where utilities and other underground conditions exist, and are particularly suited for urban settings such as courthouses, embassies, museums, banks, corporate offices, universities, mass transit facilities and parks. The XT-2300/2400 Surface Mount Sliding Bollards (Heald Matador) provide PAS 68 crash tested security while allowing freedom of travel for pedestrians and bicyclists. This surface-mount system is ideal for wide range of facilities, particularly in urban settings where foundations cannot be excavated. Ideal locations include stadiums, courthouses, parking garages, museums, parks, mass transit facilities, universities and corporate offices. 2
(XT-1200/1208) K12/L2 & K8 RETRACTABLE BOLLARDS Design Overview Ross Retractable Bollards consist of an array of three units, typically spaced on 36- inch centers. These arrays can be joined with additional groups, making them a cost effective solution for wider entrances. When deployed, XT-1200 Series Bollards extend a full 40 inches (1016 mm) high for maximum protection, which exceeds the long-used industry standard of 36 inches. In the retracted position, they re nearly invisible with only the top covers and road plates exposed. Each bollard is manufactured from durable 10-3/4inch structural steel pipe and finished with a heavy-duty galvanized coating for corrosion resistance. Various paint finishes or cast stainless steel, aluminum and bronze sleeves are available to achieve specific aesthetic requirements. The controls and operating components can be set to activate bollards individually or in groups*. A custom-engineered Hydraulic Power Unit (HPU) housed in an above-ground NEMA-rated control enclosure activates the bollards, lifting the units in 5 seconds during normal operation and 2 seconds in Emergency Fast Operation (EFO) mode. While there is no limit to the number of bollards that can be installed in an entrance, they are typically operated in groups of up to four units per HPU. Pedestrian and bicycle access non-vehicular traffic can move through freely while the bollards are in the secure position Aesthetic appeal bollards can be manufactured to complement design elements of the facility and its surrounds Low-impact security presence because bollards are commonly used in many applications and can be designed to be attractive, they don t stand out as being high-security measures, especially compared to other barrier types Wide entrances units can be added to block wider-than-normal entrances Safe operation unlike many wedge-style barriers, there are no hazardous pinch points and no need for a safety skirt Flexible controls bollards can be controlled independently or in groups to create more zones of control Ross Retractable Bollards are available with many equipment options for managing operation, including control consoles, traffic equipment, safety loops and environmental controls. With so many benefits to offer, the XT-1200 Retractable Bollard Series is ideal for: 3
Standard Features High-speed impacts where the roadway layout allows vehicles to reach higher speeds Minimal setbacks where critical assets or equipment are located close to entrances (such as in urban areas) and a high level of security is required regardless of potential vehicle speed Fast deployment where the barrier needs to be deployed quickly because it is close to the guard booth and reaction time is therefore minimal High traffic used as a final denial, this barrier can be used in tandem with standard traffic arms to process a high number of vehicles quickly Site restrictions where flush surfaces are required for snow plowing or where buttresses and posts used in other barrier designs would prevent access to wide vehicles XT-1200: DOD K12/L2 crash test certified to stop a 15,000 pound vehicle traveling 50 mph with less than 20 feet penetration of the cargo bed XT-1208: DOS K8 crash test certified with a 15,000 pound vehicle traveling 40 mph with less than one meter penetration of the cargo bed Quadra-Slide construction that provides 360 degrees of protection Bollard Height 40" (1016 mm) Crash tested in an array of three bollards on 36" centers Foundation (XT-1200 K12/L2 Model) 85" (2159 mm) deep x 132" (3048 mm) wide x 72" (1524 mm) long Foundation (XT-1208 K8 Model) 84" (2134 mm) deep x 120" (3048mm) wide x 60" (1524 mm) long Separate, removable bollard housing that provides easy access to hydraulic components for routine maintenance or quick replacement in the event of a crash Self-contained Hydraulic Power Unit (HPU) with AC (5) HP direct drive motor, 5 gallon reservoir, manual back-up hand pump and lowering valve Heavy-duty cylinders with double-lip wiper seals, heavy-duty packing glands, oversized ports and internal limit switches Normal operation mode 5 seconds. (Available with optional Emergency Fast Operation [EFO] mode of 2.0 seconds) Hydraulic oil that meets the low acute aquatic toxicity criteria of the U.S. Fish and 4
(XT-1200/1208) K12/L2 & K8 RETRACTABLE BOLLARDS Wildlife Service and the U.S. Environmental Protection Agency (EPA). This fluid is inherently biodegradable and designed to operate in temperatures from -22 F to 150 F Quick-connect HPU hose connections Controls embedded system controller plus standard NEMA-rated control enclosure Compatible with worldwide AC power sources Oversized drains with debris guards Back-up manual operation with hand pump ALGRIP slip-resistant surface on top covers and road plates Wired master and remote control console (push button and touch screen) Wired EFO control box Galvanized steel exterior barrier control enclosure Aluminum NEMA exterior barrier control enclosure Safety loops to prevent barrier deployment when authorized vehicles are over the loop, except in Emergency Fast Operation mode Wrong-way detection Over-speed detection Heat-trace system to keep bollards functioning properly in snow and ice conditions Reflective tape Pole-mounted traffic lights Optional Features Hydraulic accumulator for the standard AC based configuration that provides for Emergency Fast Operation (EFO) deployment of 1.5 seconds and supplemental back-up power for 3 cycles DC based system configuration that features a self-contained Hydraulic Power Unit (HPU) with DC (5) HP direct drive motor, 5 gallon reservoir, manual back-up hand pump and lowering valve. This option includes a fully integrated, batterypowered Uninterruptible Power Supply (UPS) to provide 100+ cycles without local power Steel-mesh-reinforced hydraulic hoses, rated at 3,000 psi, that give long-lasting service with a 300% safety factor Traffic arms Sump pump to drain water from foundation pit and mechanical components Hydraulic oil heater for operation in temperatures below -22 F (-30 C) Hydraulic oil cooler for operation in temperatures above 150 F (66 C) Low hydraulic fluid level switch Spare parts kit Extended warranty Optional Finish Galvanized + primed finish Galvanized + painted finish: Wash primer with polyurethane top coat. Contact Ross for a color chart Control Relay based, plus standard control enclosure Control PLC based 5
Technical Data Testing and Certifications Tested per U.S. Department of State SD- STD-02.01/SD-STD-02.01 Rev. A Certified by U.S. DOS (XT-1208; K8) Certified by DOD and listed on DOD Anti-Ram Vehicle Barrier List (XT-1200; K12/L2) Endurance tested to 200,000 cycles without barrier/component failure or excessive wear Applicable Standards ASTM A53: Steel Pipe ASTM A36: Steel Shapes Structural welding in accordance with AWS D1.1/D1.1M Installation Considerations Installed flush with road surface; no protruding joints or obstructions. Maintenance Separate outer housing allows for easy inspection and removal of hydraulic components. Regular inspection and preventive maintenance is required. Quality Control Manufacturing facility certified to ISO 9001:2015 Availability and Cost Barrier systems are typically made to order and subject to production lead times at the time of purchase. Contact Ross for details. Warranty Ross warrants that all of its manufactured products shall remain free of defects in material and workmanship under normal use for a period of one year from the date of delivery. 6
(XT-2200) M50 P1 SHALLOW MOUNT RETRACTABLE BOLLARD - HEALD RAPTOR Design Overview The XT-2200 Retractable Bollard is a shallow mount curved bollard that, when deployed, extends 39 inches (985 mm) above ground. The foundation requires only 3 cubic yards of concrete and is very compact at just 20 inches (500 mm) deep by 69 inches (1750 mm) wide by 110 inches (2800 mm) long that requires only 3 cubic yards of concrete. The curved element rolls on six heavy-duty wheels with sealed bearings and steel inner cores to provide smooth and quiet operation. When retracted, there are no protruding obstructions or hinged joints to present a tripping hazard for pedestrians or to damage vehicles. The Raptor is raised and lowered with a double-acting hydraulic cylinder for longterm reliability. Normal operation cycle time is 5 seconds and Emergency Fast Operation (EFO) mode is 1.5 seconds. A push button interface or optional Heald Hydra System controls the unit. It can be operated by any access control equipment or manually with a hand pump. The Raptor is ideal for the following conditions: Minimal excavation where underground utilities, high water tables or other site conditions limit excavation depth Non-standard roadway widths it can secure narrow roadways more cost effectively than typical wide three-bollard arrays Pedestrian and bicycle access nonvehicular traffic can move through freely while the bollards are in the secure position Safe operation unlike many wedge-style barriers, there are no hazardous pinch points and no need for a safety skirt High-speed impacts where the roadway layout allows vehicles to reach higher speeds Minimal setbacks where critical assets or equipment are located close to entrances (such as in urban areas) and a high level of security is required regardless of potential vehicle speed Fast deployment where the barrier needs to be deployed quickly because it is located close to a guard booth and reaction time is therefore minimal Site restrictions where flush mounting with the roadway surface is required for snow plowing or where buttresses and posts would prevent access to wide vehicles High traffic used as a final denial, this barrier can be used in tandem with standard traffic arms to quickly process a high number of vehicles Architectural appeal contemporary style offers a modern twist on the typical bollard design Flexible controls bollards can be controlled independently or in small groups to create more zones of control 7
Standard Features Dual crash tested to the ASTM F2656-07 test method with a rating of M50-P1 (15,000-pound vehicle traveling 50 mph with less than 1 meter penetration) and the PAS 68:2010 test method with a classification of V/7500(N3)/80/90:3.3/18.9 (7.5 tonne vehicle traveling 80 kph with 3.3 m penetration) Bollard height 38.8" (985 mm) Bollard width 14.96" (380 mm) Crash tested as a single unit Foundation 20" (500 mm) deep x 68.9" (1750 mm) wide x 110.2" (2800 mm) long Hydraulic Power Unit (HPU) with heavy-duty AC motor, immersed pump, extra heavy-duty solenoid valves, fluid reservoir and manual back-up hand pump Barrier housing with removable maintenance cover and integrated rebar provided by Ross Normal operation mode 5 seconds. (Available with optional Emergency Fast Operation [EFO] mode of 1.5 seconds) Quick-connect HPU hose connections Controls PLC-based NEMA rated control enclosure Compatible with worldwide AC power sources ALGRIP slip-resistant surface on top covers and road plates 8
(XT-2200) M50 P1 SHALLOW MOUNT RETRACTABLE BOLLARD - HEALD RAPTOR Optional Features Hydraulic accumulator for the standard AC based configuration that provides for Emergency Fast Operation (EFO) deployment of 1.5 seconds and supplemental back-up power for 3 cycles Steel-mesh-reinforced hydraulic hoses, rated at 3,000 psi, that give long-lasting service with a 300% safety factor Controls Heald HYDRA multi-head, universal command and control system Wired master and remote control console (push button and touch screen) Wired EFO control box Galvanized steel exterior barrier control enclosure Aluminum NEMA exterior barrier enclosure. Vehicle detection loops Heat-trace system to keep bollards functioning properly in snow and ice conditions Reflective tape Pole-mounted traffic lights Traffic arms Sump pump to drain water from foundation pit and mechanical components Hydraulic oil heater for operation in temperatures below -22 F (-30 C) Hydraulic oil cooler for operation in temperatures above 150 F (66 C) Low hydraulic fluid level switch Spare parts kit Extended warranty Optional Finish Galvanized + primed finish Galvanized + painted finish: Wash primer with polyurethane top coat. Contact Ross for color chart 9
Technical Data Testing and Certifications ASTM F2656-07 M50-P1 rating and C40-P1 rating PAS 68:2010 with a classification of V/7500(N3)/80/90:3.3/18.9 Certified by DOD and listed on DOD Anti-Ram Vehicle Barrier List Applicable Standards ASTM A53: Steel Pipe ASTM A36: Steel Shapes Structural welding in accordance with AWS D1.1/D1.1M Installation Considerations No separate reinforcement of concrete is required. Crash tested as a single unit to allow for maximum flexibility in placement. Installed flush with road surface, no protruding joints or obstructions. Maintenance Regular inspection and preventive maintenance is required. Quality Control Manufacturing facility certified to ISO 9001:2015 Availability and Cost Barrier systems are typically made to order and subject to production lead times at the time of purchase. Contact Ross for details. Warranty Ross warrants that all of its manufactured products shall remain free of defects in material and workmanship under normal use for a period of one year from the date of delivery. 10
(XT-2300/2400) PAS68 SURFACE MOUNT SLIDING BOLLARDS - HEALD MATADOR Design Overview The Matador Surface Mount Automated Bollard System is available as a three-bollard (XT-2300) or four-bollard (XT-2400) array. It consists of one or two sliding bollards that, when activated, slide behind stationary bollards located on either side. The Matador can be surface mounted with bolts for rapid deployment or recessed into a new or existing foundation to eliminate uneven transitions in the roadway surface. The Matador allows for a constant flow of pedestrian traffic and the optional stainless steel elements provide greater architectural appeal. The mounting plate design eliminates pinch points, trap hazards and voids, making it safe for passing pedestrians. The XT-2300 protects 9-foot-wide traffic lanes with two fixed bollards and a single moving bollard in the center. The XT-2400 protects 12-foot-wide traffic lanes with two fixed bollards and two moving bollards in the center. The Matador Bollard System is available with numerous equipment options for managing operation including control consoles, traffic equipment, safety loops and environmental controls. It is ideal for the following conditions: Restricted excavation where underground utilities, high water tables or other site conditions restrict excavation Temporary installation because it can be installed with minimal disruption to the road surface, it is ideal for short term placement Pedestrian and bicycle access nonvehicular traffic can move through freely while the bollards are in the secure position 11
Safe operation eliminates the pinch points found in many wedge-style barriers and the need for a safety skirt Architectural appeal a variety of finishes including stainless steel, aluminum and bronze are available to meet aesthetic requirements Low-impact security presence because bollards are commonly used, they blend in well with the surrounding streetscape and don t draw attention to high-security measures Standard Features Crash tested to the PAS 68:2010 test method with a classification of V/7500[N2]/48/90:0.0/0.0 (7500 kg vehicle traveling 48 kph at 90 impact angle, with zero penetration) Bollard height 44.9" (1140 mm) above road surface Bollard spacing 55.7" (1415 mm) Clear opening, Matador 3 102.7" (2608 mm) Clear opening, Matador 4 158.5" (4025 mm) Base Unit Size, Matador 3 159.8" x 84.3" x 4.9" (4060 mm x 2140 mm x 125 mm) Base Unit Size, Matador 4 208.7" x 84.3" x 4.9" (5300 mm x 2140 mm x 125 mm) Hydraulic Power Unit (HPU) with one or two heavy-duty AC motors, immersed pump, extra heavy-duty solenoid valves, fluid reservoir and manual back-up hand pump Normal operation 7-8 seconds Quick-connect HPU hose connections Controls PLC-based NEMA rated control enclosure Compatible with worldwide AC power sources 12
(XT-2300/2400) PAS68 SURFACE MOUNT SLIDING BOLLARDS - HEALD MATADOR Optional Features Fixed Matador configuration, which features three or more stationary bollards and offers surface mounted static PAS68 security. This unit can be combined with modular extension plates to add as many additional fixed bollards as required Controls Heald HYDRA multi-head, universal command and control system Wired master and remote control console Galvanized steel exterior barrier control enclosure 13
Aluminum NEMA exterior barrier enclosure Vehicle detection loops Heat-trace system to keep bollards functioning properly in snow and ice conditions Reflective tape Pole-mounted traffic lights Traffic arms Hydraulic oil heater for operation in temperatures below -22 F (-30 C) Hydraulic oil cooler for operation in temperatures above 150 F (66 C) Low hydraulic fluid level switch Spare parts kit Extended warranty Optional Finish Galvanized + primed finish Galvanized + painted finish: Wash primer with polyurethane top coat. Contact Ross for color chart Stainless, aluminum and bronze sleeves Technical Data Testing and Certifications Structural welding in accordance with AWS D1.1/D1.1M Installation Considerations Can be surface mounted on appropriate base (no excavation required). Low ramps are used to facilitate vehicle access Can be recessed into road surface, requiring an excavation of just 4.7 (120 mm) Flat surfaces are required for installation of barrier To achieve rated crash resistance, unit shall be bolted to concrete road or base Maintenance Driving surfaces should be kept clean to ensure unimpeded barrier motion. Regular inspection and preventive maintenance is required. Quality Control Manufacturing facility certified to ISO 9001:2015 Availability and Cost Barrier systems are typically made to order and subject to production lead times at the time of purchase. Contact Ross for details. Warranty Ross warrants that all of its manufactured products shall remain free of defects in material and workmanship under normal use for a period of one year from the date of delivery. Tested per PAS 68:2010 with a classification of V/7500(N2)/48/90:0.0/0.0 Applicable Standards ASTM A53: Steel Pipe ASTM A36: Steel Shapes 14
Ross offers a complete line of Perimeter Security Products Wedges & Plates Passive Bollards Active Bollards Gates & Fences Ross Technology Corporation 104 North Maple Avenue Leola, PA 17540-0646 US: 800-345-8170 International: +01(717)656-2200 Fax: 717-656-3281 Email: sales@rosstechnology.com RossTechnology.com