PAGE 28 EMERGENCY EXIT SIGNAGE GUIDANCE All our Eterna Emergency Exit Signage comply with current Exit Signage Regulations using the Signs Directive format. 4 Our Eterna legends fulfil the legal and technical requirements for exit signs 4 Extensions to existing installations should be made in the same format as originally installed 4 Up arrow option available for all models For installations requiring ISO 7010 format legends contact our sales team for more information
LED EMERGENCY LIGHTING PAGE 29 All our Emergency Lighting products comply with the BS EN 60598-2-22 Emergency Lighting Standard. All products in this section have 5 year warranties available ETERNAPRO 5 YEAR WARRANTY n LED Emergency Battens + High Output Versions Page 30 n LED 5ft Twin Slimline Emergency Ceiling Fitting Page 30 n LED Single Or Twin Weatherproof Fittings Page 30 n LED Colour Selectable Carina Lights Page 31 n LED Circular Or Square Utility Lights Page 32 n LED Full, Eyelid Or Grill Aluminium Wall Lights Page 33 n LED Non Maintained Emergency Downlight Page 34 n LED Maintained Recessed Emergency Fittings Page 34 n LED Emergency Hanging Exit Sign Light Page 35 n LED IP65 Twinspot Emergency Light Page 35 n LED IP20 Emergency Twinspot Fitting Page 35 n Emergency Battery Pack For RDL Range & LED Panels Page 35 n LED Slim Maintained Emergency Exit Box Page 36 n LED Maintained Emergency Exit Box Sign Page 36 n LED Maintained / Non Maintained Emergency Bulkheads Page 36
PAGE 30 IP20 LED 5FT / 6FT BATTENS + HIGH OUTPUT VERSIONS 5FT LED TWIN SLIMLINE EMERGENCY CEILING FITTING A slim, modern design LED ceiling fitting which offers a more stylish alternative to traditional battens. Where a more aesthetically pleasing fixture is desirable this versatile and elegant light source is suitable for commercial, retail and domestic applications. Polycarbonate and aluminium construction Push terminal connections Pre-wired for easy installation Minimum 3 hour functionality in emergency mode LED glows green in standby mode and super bright white light in the event of a mains failure 118 lumens in emergency mode See PAGE 44 for non emergency version M.O.M: 1 / O.P.Q: 6 ALL FITTINGS: White / 4200K / 35,000 hrs / IP20 Full photometric data available to enable lighting designs. Light output is equivalent or superior to traditional fluorescent battens. White / 50W / 4000K / 5000 lm / 40,000 hrs 1503mm (5ft) 127mm 43mm Emergency Box 60mm 46mm 50mm Pressed steel body and polycarbonate diffuser LED tray can be removed from the housing for easy installation 20mm knockout glands at each end for through wiring options BESA box mounting Gear tray retaining straps Push terminal connections Pre-wired for easy installation LED glows green in standby mode and super bright white light in the event of a mains failure Minimum 3 hour functionality in emergency mode 118 lumens in emergency mode See PAGE 43 for non emergency versions M.O.M: 1 / O.P.Q: 6 ELEGAN5EM3 5FT (1460mm) 6FT (1730mm) Emergency module glows green in standby mode Bright white glow in emergency mode 60mm Version Wattage Luminaire Lumens STANDARD OUTPUT LED BATTENS LBAT5FTEM3 5FT 38W 4800 lm LBAT6FTEM3 6FT 48W 6000 lm HIGH OUTPUT LED BATTENS LBAT5HOEM3 5FT 65W 7900 lm LBAT6HOEM3 6FT 70W 8600 lm 73mm IP65 LED SINGLE/TWIN 5FT EMERGENCY WEATHERPROOF FITTINGS BOTH FITTINGS: Grey / 5000K / 30,000 hrs / IP65 1560mm (5ft) 95mm Single: 90mm Twin: 135mm Version Wattage Luminaire Lumens WPLEDEM351 Single 5ft 30W 3000 lm WPLEDEM352 Twin 5ft 60W 6000 lm Superb one for one replacement for traditional fluorescent fixtures. Polycarbonate housing and diffuser Multiple fixing options - supplied with surface mounting brackets and suspension hooks Gear tray retaining strap for easy installation IES files available Stainless steel clips Push-fit terminal block 3 hour duration maintained operation: facility for non-maintained mode or remote switching See PAGE 45 for non emergency versions Single = M.O.M: 1 / O.P.Q: 6 Twin = M.O.M: 1 / O.P.Q: 4
IP65 LED EMERGENCY COLOUR TEMPERATURE SELECTABLE FITTINGS ALL FITTINGS: 17W / 35,000 hrs / IP65 / A Rated 3100K 1250 lm 4200K 1350 lm 6400K 1300 lm PAGE 31 ALL FITTINGS: Colour temperature selectable - options of 3100K, 4200K & 6400K easily set by a dip switch on the gear tray Full circular LED array Polycarbonate construction IP65, ceiling or wall mounted 325mm Plug in connector between the terminal block and the gear tray. Terminal block is located on the base, allowing for easy wiring and the gear tray to be removed during installation See PAGE 21 for non emergency versions M.O.M: 1 / O.P.Q: 8 EMERGENCY VERSIONS: 3 hour maintained mode as standard which can also be configured for non maintained operation STANDARD ON/OFF MICROWAVE SENSOR VERSIONS: Adjustable microwave sensor: with options to adjust 2-50 lux or disable, detection range 10-100% and time 5 secs - 15 mins The microwave sensor is discreetly placed behind the diffuser: making it unobtrusive so there is no compromise to the appearance of the fitting or the room design STEP DIM (CORRIDOR MODE) MICROWAVE SENSOR VERSIONS: Operation at 100% light level after last presence detection, reducing to 10% light output after installer selected time delay Delay time to 10% operation adjustable: 5 sec 30 sec 1 min 5 min 15 min 30 min 30~150 detection angle 12~18m adjustable detection range: 100% 75% 50% 25% 10% Daylight sensitivity adjustment: 2Lux 5Lux 10Lux 30Lux 50Lux Photocell Disable Detection is possible through doors, glass panels and thin walls 110mm Colour STANDARD EMERGENCY CSLEDCREM3 Polished Chrome CSLEDWHEM3 White ON/OFF MICROWAVE SENSOR + EMERGENCY MSCSLCREM3 Polished Chrome MSCSLWHEM3 White 10% STEP DIM (CORRIDOR MODE) MICROWAVE SENSOR + EMERGENCY SDCSLCREM3 Polished Chrome SDCSLWHEM3 White = ON = OFF Standard shown
PAGE 32 IP65 LED EMERGENCY UTILITY FITTINGS WITH OPAL / PRISMATIC DIFFUSER ALL FITTINGS: 18W / 4000K / 35,000 hrs / IP65 / A+ Rated High output, energy saving utility LED wall / ceiling fixtures with standard, emergency & multi-function microwave control versions. Both opal & clear versions are available for either smooth diffused effect or maximum light output. Diffusers are supplied not fitted to bases and fully captive diffuser fixing screws are utilised to save installation time. Multi-function microwave versions provide the best in flexibility & energy saving options. Prismatic circular diffuser Captive fixing screws Version Diffuser + Lumens CIRCULAR FITTINGS CIROPALEM3 Standard Emergency Opal CIROPALMW3 Multi-function MW Sensor + Emergency 1400 lm CIRPRISEM3 Standard Emergency Prismatic CIRPRISMW3 Multi-function MW Sensor + Emergency SQUARE FITTINGS 1600 lm SQOPALEM3 Standard Emergency Opal SQOPALMW3 Multi-function MW Sensor + Emergency 1400 lm SQPRISEM3 Standard Emergency Prismatic SQPRISMW3 Multi-function MW Sensor + Emergency 1600 lm Opal square diffuser Multi-function MW Sensor Push fit terminal block CIR: Ø 290mm SQU: 250mm FULL CIRCULAR / SQUARE LED ARRAY 100mm Opal circle Opal square Hinged gear tray Captive fixing screws Four 20mm cable entries on the side and one to the rear See PAGE 22 for non emergency versions EMERGENCY VERSIONS: 3 hour maintained mode as standard which can also be configured for non maintained operation MULTI-FUNCTION MICROWAVE SENSOR VERSIONS: Detection sensitivity adjustable - 10/50/75/100% Daylight sensor adjustable - 5/15/50 Lux/Disable Mounting height - maximum 6mtr Detection zone - maximum 16mtr diameter x 6mtr height Detection angle - 150 (wall mounted), 360 (ceiling mounted) MULTI-FUNCTION MICROWAVE SENSOR WITH 3 INSTALLER OPTIONS: Prismatic square Prismatic circle Standard On/Off Mode: operation at 100% light level then off after last presence detection. Operation on time can be set at 5 seconds/90 seconds/3 minutes/10 minutes Corridor Mode : operation at 100% light level after last presence detection which can be set at 5 seconds/90 seconds/ 3 minutes/10 minutes, then continuous operation at 10% light level Corridor & Off Mode: operation at 100% light level after last presence detection which can be set at 5 seconds/ 90 seconds/3 minutes/10 minutes, then operation at 10% light level which can be set at 30 seconds or 10 minutes, then off
IP65 LED EMERGENCY FULL, EYELID OR GRILL ALUMINIUM WALL LIGHTS ALL FITTINGS: 18W / 4200K / 35,000 hrs / IP65 / A+ Rated ALEM3BKFUL shown ALEM3WHEYE shown PAGE 33 Full Modern and robust design with options including full, eyelid and grill case, black and white finish, and standard, emergency, multi function microwave and multi function microwave emergency. Colour Version Luminaire Lumens Eyelid FULL ALEM3BKFUL ALEM3WHFUL Black White Emergency ALMF3BKFUL Black Multi-function MW Sensor ALMF3WHFUL White + Emergency 1400 lm Grill Standard push fit terminal block EYELID GRILL ALEM3BKEYE ALEM3WHEYE Black White Emergency ALMF3BKEYE Black Multi-function MW Sensor ALMF3WHEYE White + Emergency ALEM3BKGRI ALEM3WHGRI Black White Emergency ALMF3BKGRI Black Multi-function MW Sensor ALMF3WHGRI White + Emergency 1300 lm 1400 lm Die-cast aluminium base and bezel Polycarbonate diffuser Full circular/eyelid LED array Plug in connector between the terminal block and the gear tray. Terminal block is located on the base, allowing for easy wiring and the gear tray to be removed during installation Four 20mm cable entries Tamper-proof, captive, stainless steel allen key screws See PAGE 23 for non emergency versions M.O.M: 1 / O.P.Q: 1 EMERGENCY VERSIONS: 3 hour maintained mode as standard which can also be configured for non-maintained operation MULTI-FUNCTION MICROWAVE SENSOR VERSIONS: Detection sensitivity adjustable - 10/50/75/100% Daylight sensor adjustable - 5/15/50 Lux/Disable Mounting height - maximum 6mtr Detection zone - maximum 16mtr diameter x 6mtr height Detection angle - 150 (wall mounted), 360 (ceiling mounted) MULTI-FUNCTION MICROWAVE SENSOR WITH 3 INSTALLER OPTIONS: ALEM3WHGRI shown Ø 365mm FULL: 100mm EYE: 120mm GRILL: 130mm Standard On/Off Mode: operation at 100% light level then off after last presence detection. Operation on time can be set at 5 seconds/90 seconds/3 minutes/10 minutes Corridor Mode : operation at 100% light level after last presence detection which can be set at 5 seconds/90 seconds/ 3 minutes/10 minutes, then continuous operation at 10% light level Corridor & Off Mode: operation at 100% light level after last presence detection which can be set at 5 seconds/ 90 seconds/3 minutes/10 minutes, then operation at 10% light level which can be set at 30 seconds or 10 minutes, then off
PAGE 34 IP20 LED 1.4W NON MAINTAINED EMERGENCY DOWNLIGHT This LED compact recessed emergency light is ideal for use in corridors, stairwells and other places that require a smart, discreet emergency unit. Aluminium construction Compact design Matt silver and white trims included Pre-wired for easy installation LED glows green in standby mode and super bright white light in the event of a mains failure Excellent alternative to a converted downlight Minimum 3 hour functionality in emergency mode 118 lumens in emergency mode 32mm diameter hole cut out size M.O.M: 1 / O.P.Q: 20 Matt Silver or White Trim / 1.4W Actual size: Ø 45mm 2 X COLOUR TRIMS INCL. 45mm 33mm LDLEM3 Bright white glow in emergency mode Emergency charge light Low energy alternative to standard emergency exit fittings Emergency module glows green in standby mode Download the SPACING TABLE from: /product/ldlem3/ LED MAINTAINED RECESSED EMERGENCY FITTINGS BOTH FITTINGS: White / 6500K / 18,000 hrs LEDMDDEM3 Pressed steel body Hinged gear tray: easy installation and maintenance Hole cut out size: 115mm x 320mm LEDREM3 = M.O.M: 1 / O.P.Q: 10 LEDMDDEM3 = M.O.M: 1 / O.P.Q: 6 RLGDLR / RLGDUP = M.O.M: 1 / O.P.Q: 25 LEDREM3 Polycarbonate reeded diffuser: unobtrusive solution for discreet emergency lighting Facility for non-maintained mode Facility for remote switching LEDMDDEM3 Slotted pressed steel panel housing polycarbonate down arrow exit legend for unobtrusive exit path designation LEDREM3 320mm 110mm 410mm 135mm 90mm 180mm 260mm Version Wattage Lumens LEDREM3 Reeded Diffuser 5.20W 162 lm LEDMDDEM3 Edge Lit Panel & Diffuser 3.5W - Up & left / right legend available for LEDMDDEM3 RLGDUP RLGDLR LEDMDDEM3 LEDREM3
Remote connection box complete with adjustable length suspension cable (max 80cm) Supplied with a double-sided down arrow exit legend - left/right & up arrow legends available separately 3 hour maintained mode as standard which can also be configured for non-maintained or remote switched operation Viewing distance 29m Test button and LED charge light SIGNLEDEM3: M.O.M: 1 / O.P.Q: 6 SIGNLGD/UP: M.O.M: 1 / O.P.Q: 100 LED EMERGENCY HANGING EXIT SIGN LIGHT White / 2.3W / 6000K / 171 lm / 25,000 hrs SIGNLGD 55mm Up to 800mm Max. 172mm 340mm SIGNLGDUP 45mm SIGNLEDEM3 PAGE 35 335mm 8mm IP65 LED TWINSPOT EMERGENCY FITTING White / 7W (2 x 3W) / 3500K / 441 lm / 30,000 hrs / IP65 Twin 3W LED projectors: provide superior light output to traditional twinspot fittings Horizontally and vertically adjustable heads, 180 rotation across the horizontal plane IP65 rating utilising high quality polycarbonate enclosure: for installation in wet or dusty environments Individual indicator to show Lamps Healthy and Charge Reduced battery capacity requirement: allows a more compact design reducing the weight dramatically compared to traditional products facilitating easier installation Minimum 3 hour non-maintained functionality in emergency mode M.O.M: 1 / O.P.Q: 6 295mm 125mm 300mm 190mm 60mm 70mm IP20 LED EMERGENCY TWINSPOT FITTING 75mm LEDTWNSPOT White / 3.4W / 6000K / 405 lm / IP20 Reduced battery capacity requirement allows a more compact design reducing the weight dramatically compared to traditional products facilitating easier installation. TSPOTLIP20 50mm Polycarbonate construction Individual indicator to show Lamps Healthy and Charge Horizontally and vertically adjustable heads, 180 rotation across the horizontal plane 3 hour non-maintained operation M.O.M: 1 / O.P.Q: 6 170mm 110mm 280mm 55mm 310mm EMERGENCY BATTERY PACK FOR ETERNA LED FITTINGS 250mm White / 65W Max / IP20 55mm 110mm EBPM3 Enables Eterna LED commercial downlights (RDL range on PAGE 49) and LED panel lights (See PAGE 26-27) to be converted into emergency luminaires, rated at 65W max 3 hours duration in emergency mode Push fit plug and socket: allows quick & easy installation Facility for non maintained mode and for remote switching LED charge light Control gear can be removed from the housing: allows use in installations with smaller hole cut out M.O.M = 1 / O.P.Q = 1 Download the EASY STEP BY STEP WIRING GUIDE from: /product/ebpm3/
PAGE 36 An aesthetically pleasing, low energy, ultra slim alternative to conventional exit boxes Ultra slim design: excellent solution where a more compact fitting is required 3 hour maintained mode as standard which can also be configured for non maintained operation Diffuser on base: for added downward illumination of exit path Interchangeable down, up, left & right arrow exit legends included Long life energy efficient LED light source eliminates lamp replacement cycle without compromising panel visibility distance Facility for remote switching LED charge light For wall mounting only 34 metres viewing distance M.O.M: 1 / O.P.Q: 10 393mm IP20 SLIM LED MAINTAINED EMERGENCY EXIT BOX White / 5.2W / 30,000 hrs / IP20 27mm 193mm EBLSLIMM Down, up, left & right legends included IP20 LED MAINTAINED EMERGENCY EXIT BOX SIGN White / 4W / 30,000 hrs / IP20 Low energy alternative to standard emergency exit signs. Steel construction 3 hour maintained mode as standard which can also be configured for non maintained operation Facility for remote switching Interchangeable polycarbonate down arrow exit legend included Diffuser on base: for added downward illumination of exit path Long life energy efficient LED light source eliminates lamp replacement cycle without compromising panel visibility distance LED charge light and battery test button Viewing distance: 34m EXIT3MLED = M.O.M: 6 / O.P.Q: 6 Legends = M.O.M: 1 / O.P.Q: 100 390mm 60mm EXIT3MLED 192mm Full range of alternative legend directional panels available EBLGDL EBLGDR EBLGDU IP65 LED MAINTAINED / NON MAINTAINED EMERGENCY BULKHEADS BOTH FITTINGS: White / 6000K / 30,000 hrs / IP65 Polycarbonate construction Internal or external use Low energy alternative to standard 20mm gland entries as standard fluorescent emergency bulkheads. Minimum 3 hour functionality in emergency mode High output LEDs with bright white light Semi recessed fixing: allows a more discreet installation option Dedicated self adhesive legend pack included with a combination of symbols: allows multiple exit path designation options (LGDSET) Fitting / Frame = M.O.M: 1 / O.P.Q: 12 LGDSET = M.O.M: 12 / O.P.Q: 12 EMLED3M: Facility for remote switching and non-maintained mode 235 lm when connected to mains,150 lm when connected to battery BULKHEAD FRAME (BULKFRAME): For use with emergency bulkheads Pressed steel construction Spring retaining clips Semi recessed fixing: allows a more discreet installation option Hole cut out size: 350mm x 117mm 105mm 346mm 392mm 45mm 150mm Version Wattage Lumens EMLED3M Maintained 7W 235/150 lm EMLED3NM Non Maintained 2W 150 lm Hinged gear tray & push fit terminal block: allows for quicker and easier installation and maintenance 355mm 70mm 110mm