Revised 02-2-2010 Highly Styled, Low Cost Serpentine Drive Installation Instructions Style Track Ford "FE" Kit #19040 (Chrome Alternator and Power Steering Pump) Kit #19045 (Billet Alternator and Power Steering Pump)
Included Parts List Main Front Bracket P/N 19041 1-19041-A... Main Front Bracket Body 2-740-A... Idler Pulley Body 2-02-A... Idler Pulley Cap - S022... 8 2 x 8" Lg Soc Hd Bolt 1 - S150... 5 16" x 1 1 2" Lg Soc Hd bolt 2 - S248... 8" x 1" Lg Soc Hd Bolt 2 - S256... 8" x 2" Lg Soc Hd Bolt 1 - S272... 8" x 4" Lg Soc Hd Bolt 1 - S277... 8" x 4 4" Lg Soc Hd Bolt 2 - S7... 8" x 1 1 2" Thd Stud 1 - S55... 8mm x 5mm Metric Soc Hd Bolt 2 - S622... 8" Id Lock Nut 2 - S666... 8" Id Flat Washer 2 - S778... 4.550" Lg Threaded Spacer Stainless 2 - AC-1.50... Aluminum Spacer 1.50" Lg 1 - TP-2.750... Tube Spacer 2.750" Lg 2 - MM100... Adjustment Bolt Bushing Alternator Rear Support P/N 19042 1-19042-A... Alt Rear Support Brk Body 1 - S270... 8" x 1 2" Lg Soc Hd Bolt 1 - S45... 5 8" x.850" Lg Set Screw 1 - TP-1.70... Tube Spacer 1.70" Lg Power Steering Rear Support P/N 1904 1-1904-A... Power Steering Rear Support Brk Body 1 - S262... 8" x 2 1 2" Lg Soc Hd Bolt 1 - S45... 8" x.850" Lg Set Screw 1 - TP-.650... Tube Spacer.650" Lg Belt Adjustment Tool P/N 21206 1 - MM101... RH Rod End 1 - MM102... LH Rod End 1 - MM105... 1" Threaded Rod Pulley Kit P/N 19040-206 1-198-A... Crank Shaft Pulley 1-1982-A... Water Pump Pulley 1-206-A... Alternator Pulley 1-221-A... Alternator Fan 1-06-A... Alternator Cap 1-1-A... Water Pump Cover 1-60-A... Power Steering Pulley Cap 1-629-A... Power Steering Pulley - S028... 8 2 x 1" Lg Soc Hd Bolt - S106... 1/4" x 1 1 4" Lg Soc Hd bolt 4 - S186... 5 16" x 7 8" Lg Soc Hd Bolt - S248... 8" x 1" Lg Soc Hd Bolt 1 - S685... 11 16" Id Lock Washer Accessories Kit # 19040 1 - P168... Aluminum Water Pump 1 - P04... Power Steering Pump Chrome 1 - P572... Alternator Chrome Accessories Kit # 19045 1 - P168... Aluminum Water Pump 1-9600... Power Steering Pump Billet Aluminum 1-9650... Alternator Billet Aluminun Alt Relocator Bracket P/N 21074 1-21074-A... Alt Relocator Bracket 2 - S244... 8" x 4" Lg Soc Hd Bolt 1 - S12... 8" x 1" Lg Hex Hd Bolt Required Tools and Materials RTV Silicone Loc-Tite Thread Locker Anti-seize Compound Gasket Scraper, Steel Wool or Sandpaper to clean gasket surfaces 16" Allen Head Driver 5 16" Allen Head Driver 1 4" Allen Head Driver 6mm Allen Head Driver 5 8" Combo Wrench 9 16" Combo Wrench 11 16" Combo Wrench 4" Combo Wrench Socket Wrench & Extension 10mm 12pt. socket 12mm 12pt. socket Serpentine Belt 6" Tech Support 1-888-729-9070
Preparing to Install Disconnect the battery to prevent accidental engagement of starter motor. Drain coolant from system If your A/C is intact and charged it must be evacuated. This is best done by a professional garage with proper recycling equipment Remove the existing alternator, air conditioning compressor and associated brackets. Installing the Kit Remove all pulleys and water pump. Remove all traces of old gasket and sealer with gasket scraper and steel wool pad. Clean threads in block by chasing with appropriate thread chasers. 1. (S7) 8" x 1 1 2" Studs Photo-1 Ensure the sealing face of the coolant outlets are clean, flat and free of old gasket material. Apply a small amount of RTV silicone to one end of each mounting stud to prevent coolant seepage. Install the (2) 8 x 1 1 2" Studs (S7) into the two upper water pump mounting holes and install the Paper Gaskets. (S788) Stainless Steel Spacers Photo-2 Install the Provided Water pump (P168) and in the Two upper Water Pump holes use the two Stainless Steel 4.550 long Spacers (S788) Threading them onto the Studs. (TP-1.70) Spacer Tube. (S45) Threaded Bushing Photo-4 In the lower Drivers side Water Pump hole install the rear P/S rear support bracket (1904-A) Use a 8 x 2 1 2" SHCS (S262) and a (TP-.650) Spacer Tube, Also install a 5 8 x.850 Threaded Bushing (S45). 2. Photo- In the Lower Passenger side Water Pump Hole install the Rear Alt. Support Bracket (19042-A) use a 8 x 1 2" SHCS (S270) and a (TP-1.70) Spacer tube also install a 5/8 x.850 Threaded Bushing (S45) into the outer hole as shown, (do not tighten at this time) you will need to adjust this later. (TP-.650) Spacer Tube (S45) Threaded Bushing 4. www.marchperf.com
Photo-5 Installing the Main Front Plate, (19041-A) using (2) 8-16 x 2" SHCS (S256) and (2) AC-1.50 Alum Spacer Tubes in the lower holes and (2) 8 x 1" (S248) SHCS in the upper holes. (AC-1.50) Spacer Tube 5. 6. Photo-7 Installing the Alternator, (P572) Chrome or (9650) March Billet Alternator. In the lower Mounting hole use (1) 8 x 4" SHCS (S272) and (1) /8 Lock nut (S622). Line up the rear support bracket and run the 8 x 4" bolt thru the front bracket make sure the rear bushing is tight to the back of the Alternator unit and install the 8" lock nut. In the upper Mounting Slot use (1) (S150) 5 16 x 1 1 2" SHCS and 8" Alum. Counter sunk bushing (MM100) and (1) 5 16 x 1 1 2" SHCS for the Billet Alternator or a 8MM x 5mm SHCS (S55) for the Chrome Alternator. 8. Photo-6 Install the Two (740) Idlers) use (2) 8 x 1 4" SHCS (S254) and (2) 8" Washers (666) as shown. (MM100) Bushing 7. Photo-8 Installing the power Steering Pump (P04) Chrome or (9600) March Billet Pump by first installing the Power Steering Relocation Bracket (21074) to the Pump, use (2) 8 x 4" SHCS (S244) and (1) /8 x 1" Hex Head Bolt as shown. 9. Photo-9 Install the Pump to the Main Bracket in the Lower Hole of the Main Bracket Install a 8 x 4 4 " SHCS (S277) Between the P/S Adapter Bracket and the Rear support us a (TP-2.750) Tube Spacer. Make sure and ajust the rear (S45) Bushing so its tight. Add a 8" lock nut to the rear (S622), leave loose at this time. Tilt the power Steering pump inward for now leaving the upper slot open. (TP-2.750) Spacer Tube Tech Support 1-888-729-9070
Photo-10 Install the Water Pump Pulley (1982) using four 5 16 x 7 8" SHCS (S184). 11. Photo-12 Install the Alt Fan (221) and pulley (206) and Pulley Cap (1). Install the Power Steering Pulley (629) and the Power Steering Pulley Cap (60). 10. Photo-11 Install the Crank Pulley (198-A) using three 8 x 1" SHCS (S248) 1. Photo-14 Slip the supplied March Adjustment tool over the two (MM100) bushings and using a wrench turn the adjustment tool outward to tighten the serpentine belt to 100 ft. lbs. Use the holes in the adjustment tool to tighten both 8mm socket head cap screws when correct belt tension has been achieved. Remove the adjustment tool and keep for future use. 12. Photo-1 Push the Alternator and A/C inward to their fullest position and install the 6" Belt. Install the 5 16 x 1 1 2" SHCS (S150) and the MM100 Bushing in the upper P/S slot. Instll the (2) Idler Caps (02). 14. TIP: Your Serpentine belt is tight when it can t be moved by more then 1 2" inch at it s longest span between pulleys. The belt should not be able to be twisted by more then half a turn. Check and tighten all bracket bolts and alternator and power steering lower mounting bolts, turn engine over once by hand to check for any belt rubbing and proper belt alignment. Run engine three minutes and check belt tension again. www.marchperf.com
MARCH PERFORMANCE, INC. 16160 PERFORMANCE WAY NAPLES, FLORIDA 4110 LIMITED WARRANTY March Performance warrants to the original retail purchaser that for a period of ninety (90) days from the date of purchase, March Performance will repair or replace, at their option, any Product, which is found to be defective in material or workmanship. Exclusions from Warranty Coverage March Performance does not warrant any Product that is damaged from abuse, misuse or misapplication or not used for its intended purposes. This Limited Warranty does not cover or apply to any damage or loss sustained to the engine or any other parts which may have been caused by the defective Product and does not cover or apply to any personal injury, labor charges or any other incidental costs for damages caused by the defective Product. THIS IS THE ONLY EXPRESS WARRANTY GIVEN WITH RESPECT TO YOUR PRODUCT. ALL OTHER EXPRESS WARRANTIES, GUARANTEES, OR STATEMENTS REGARDING THE PRODUCT, WHETHER WRITTEN OR VERBAL, ARE HEREBY DEEMED NULL AND VOID AND OF NO EFFECT. Normal wear and tear and damage to the Product not caused by March Performance are also excluded from this Warranty. DISCLAIMER OF OTHER WARRANTIES EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTY WHETHER OF MERCHANTABILITY, FIT- NESS FOR A PARTICULAR PURPOSE, OR WARRANTY, SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY WILL LAST SO THAT THE PRECEDING LIMITATION MAY NOT APPLY TO YOU. Limitation on Remedies REPAIR OR REPLACEMENT AS PROVIDED IN THIS WARRANTY IS YOUR EXCLUSIVE REMEDY. MARCH PERFORMANCE SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGE FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THE PRODUCT. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OF CONSEQUESTIAL DAMAGES SO THE PROCEEDING LIMITATIO OR EXCLUSIONS MAY NOT APPLY TO YOU. YOU HAVE NO RECOURSE OR REMEDY FOR DAMAGE OR DEFECT CAUSED BY MISUSE, ABUSE OR NEGLIGENCE. THIS WARRANTY GIVES YOU SPECIFIC RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH MAY VARY FROM STATE TO STATE. Your Responsibilities: 1. Use and install the Product only for its intended purpose. 2. To avail yourself of this Limited Warranty, return the Product with a copy of the paid receipt, postage paid to: MARCH PERFORMANCE 16160 PERFORMANCE WAY NAPLES, FL 4110. When returning the Product, you must follow the directions set forth on the Warranty/Return Form on the reverse side of this Limited Warranty. If you no longer have the Warranty/Return Form, one may be obtained by contacting March Performance during normal business hours at: (888) 729-9070. 4. Shipping and/or transportation costs returning the Product to March Performance and any damage caused during shipping are your responsibility. March Performance will pay for shipping and/or transportation costs incurred in returning the Product to you. LIMITED WARRANTY WARRANTY/RETURNS FORM No product mounted is considered for credit unless it is a manufacturer defect. All products returned for any reason must reference an authorization number (RGA). The RGA number is obtained by calling place of purchase during normal business hours. Any product returned without the RGA# written on the return package next to the return shipping label will be refused. All returns must ship via UPS and be properly packaged in the original carton. Return freight charges are the responsibility of the customer unless the product was shipped in error. March product returned after (1) year from date of purchase will not be accepted unless it is found to be a manufacturer defect. The customer must include a written statement describing the alleged product defect. The complete Limited Warranty is set forth on the reverse side. 100% credit issued on manufacturer defects 20% return fee on all reshelvable product 70% return fee on all repairable product NO CREDIT WILL BE ISSUED ON RETURNED PRODUCT BEYOND REPAIR March Performance thoroughly inspects all returns. It is the sole discretion of March Performance in determining the condition of all returned merchandise. To receive replacements at no charge the original product must first be received and inspected by March Performance for determination. Immediate replacements may be purchased and later credited upon inspection determination. Please Complete the Information below, detach and include with returned product. RGA# CT# Issued by: Date Purchaser s Name Phone Address Purchased Directly Through Invoice# Product ID Invoice Date Reason ** MOUNTED PRODUCTS ARE NONREFUNDABLE **