G66 Series Maximum Flow Rate: Maximum Pressure: 248.7 l/min (65.7 gpm) 48 bar (7 psi) for Metallic Pump Heads 17 bar (25 psi) for Non-metallic Pump Heads API 674 ATEX G66 with Ductile Iron pump head www.hydra-cell.eu G66 with Polypropylene pump head
G66 Series Performance Capacities Flow Max. Max. Flow Input @ 48 bar (7 psi) G66-X 1 65.7 248.7 Metering & Dosing Pressure Maximum Inlet Pressure Metallic Pump Heads: 17 bar (25 psi) Non-metallic Pump Heads: 3.5 bar (5 psi) Maximum Discharge Pressure Metallic Pump Heads: 48 bar (7 psi) Non-metallic Pump Heads: 17 bar (25 psi) Polypropylene Performance and specification ratings apply to G66 configurations unless specifically noted otherwise. API 675 Performance Characteristics of Steady State Accuracy ± 1%, Linearity ± 3% and Repeatability ± 3% can be achieved at speeds up to 1 rpm and pressures up to 48 bar (metallic pump heads) for X-cam pumps only. Maximum Flow at Designated Pressure 7. 264.9 6. 5. 14 bar (2 psi) 48 bar (7 psi) G66-X 227.1 189.3 Gallons per Minute 4. 3. 151.4 113.6 Liters per Minute 2. 75.7 1. 37.9 2 4 6 8 1 Revolutions Per Minute www.hydra-cell.eu 2
G66 Series API 674 Performance Capacities Flow Max. Max. Flow Input @ 48 bar (7 psi) G66-X 1 65.7 248 Pressure Maximum Inlet Pressure Metallic Pump Heads: Non-metallic Pump Heads: 17 bar (25 psi) 3.5 bar (5 psi) Performance and specification ratings apply to G66 configurations unless specifically noted otherwise. Maximum Discharge Pressure Metallic Pump Heads: 48 bar (7 psi) @ 1 rpm max. Non-metallic Pump Heads: 17 bar (25 psi) Maximum RPM at Designated Pressure 55 G66 48 41 34 Pressure (bar) 28 Operation on or below line complies with Item 6.8.2 of API-674 G66 21 14 7 2 4 6 8 1 12 Pump Speed (rpm) 3 www.hydra-cell.eu
G66 Series Specifications Flow Capacities @ 14 bar (2 psi) G66-X (Metallic) 1 67.8 256 Flow Capacities @ 17 bar (25 psi) G66-X (Non-metallic) 1 67.5 255 Flow Capacities @ 48 bar (7 psi) G66-X (Metallic) 1 65.7 248 Delivery @ 14 bar (2 psi) Model gal/rev liters/rev G66-X (Metallic).678.256 Delivery @ 17 bar (25 psi) Model gal/rev liters/rev G66-X (Non-metallic).675.255 Delivery @ 48 bar (7 psi) Model gal/rev liters/rev G66-X (Metallic).657.248 Maximum Discharge Pressure Metallic Heads: 48 bar (7 psi) @1 rpm Non-metallic Heads: 17 bar (25 psi) Polypropylene Maximum Inlet Pressure Metallic Heads: 17 bar (25 psi) Non-metallic Heads: 3.5 bar (5 psi) Maximum Operating Temperature Metallic Heads: Non-metallic Heads: Maximum Solids Size Inlet Port Discharge Port Shaft Diameter Shaft Rotation Bearings Oil Capacity Weight Metallic Heads: Non-metallic Heads: 93.3 C (2 F) - Consult factory for correct component selection for temperatures from 71 C (16 F) to 121 C (25 F). 49 C (12 F) - Consult factory for temperatures above 49 C (12 F). 8 microns 3 inch BSPT 3 inch NPT 2-1/2 inch SAE J518 Flange (Non-metallic) 3 inch SAE J518 Flange (Metallic) 1-1/2 inch BSPT 1-1/2 inch NPT 1-1/2 inch SAE 5.8 mm (2 inch) Reverse (bi-directional) Tapered roller bearings 7.5 litres (8 US quarts) 226 kg (5 lbs.) 133 kg (295 lbs.) Calculating Required Power 1 x rpm + gpm x psi = electric motor hp 63, 1,46 1 x rpm + l/min x bar = electric motor kw 84,428 511 Calculating Pulley Size motor pulley OD = pump rpm When using a variable frequency drive (VFD) controller, calculate the hp or kw at minimum and maximum pump speed to ensure the correct hp or kw motor is selected. Note that motor manufacturers typically de-rate the service factor to 1. when operating with a VFD. Net Positive Suction Head (NPSHr) NPSHr (feet of water) 16 15 14 13 12 11 1 9 8 7 6 5 4 3 2 1 pump pulley OD motor rpm 1 2 3 4 5 6 7 8 9 1 Revolutions Per Minute 4.5 4 3.5 3 2.5 2 1.5 1.5 NPSHr (meters of water) Self-priming: Each Hydra-Cell pump has different lift capability depending on model size, cam angle, speed, and fluid characteristics. To ensure that your specific lift characteristics are met, refer to the inlet calculations regarding friction, and acceleration head losses in your Hydra-Cell Installation & Service Manual. Compare those calculations to the NPSHr curves above. www.hydra-cell.eu 4
G66 Series Representative Drawings G66 Models with BSPT Inlet/Outlet Ports mm (Inches) 12 7) Outlet 1 1/2 BSPT or 1 1/2 NPT Ø 375.3 (14.78) Inlet 3 BSPT or 3 NPT 345. (13.59) 468.3 (18.44) 165.1 (6.5) 292.8 (11.53) 596.12 (23.47) W576 Outlet 1 1/2 BSPT or 1 1/2 NPT Ø 5.8 (2.) 12.7 (.5) Ø 375.3 (14.78) Inlet 3 BSPT or 3 NPT 172.8 (6.81) 165.1 (6.5) 292.8 (11.53) Metallic pump head models shown. Note: Contact factory for additional drawings of specific models and configurations. 5 www.hydra-cell.eu
G66 Series Representative Drawings G66 Models with SAE Flange Inlet/Outlet Ports mm (Inches) 596.12 (23.47) Outlet 1 1/2 SAE J518 Ø 5.8 (2.) 12.7 (.5) Inlet 3 SAE J518 Ø 375.3 (14.78) 345. (13.59) 468.3 (18.44) 172.8 (6.81) 165.1 (6.5) 292.8 (11.53) Metallic pump head models shown. G66 Models with SAE Flange Inlet/Outlet Ports mm (Inches) 584.23 (23.) 37.1 (1.46) Outlet 1 1/2 SAE J518 W575 Ø 5.8 (2.) 12.7 (.5) 43.5 (1.71) 345.8 (13.62) 468.3 (18.44) Inlet 2 1/2 SAE J518 18.8 (7.12) 172.8 (6.81) 165.1 (6.5) 292.8 (11.53) Non-metallic pump head models shown. Note: Contact factory for additional drawings of specific models and configurations. www.hydra-cell.eu 6
G66 Series How to Order Ordering Information 1 2 3 G 6 6 X K 4 5 6 7 8 9 1 11 12 A complete G66 Series Model Number contains 12 digits including 7 customer-specified design and materials options, for example: G66XKDGHFEPA. Order Digit Code Description 1-3 Pump Configuration G66 Shaft-driven 4 Hydraulic End Cam X Max 248.7 l/min (65.7 gpm) @ 1 rpm 5 Pump Head Version K Kel-Cell BSPT Ports or SAE Flanges 6 Pump Head Material B Brass D Ductile Iron (Nickel-plated) N Polypropylene (with Hastelloy C followers and follower screws) P Polypropylene (with 316 SST followers and follower screws) S 316L Stainless Steel 7 Diaphragm & O-ring Material G FKM T Buna-N 8 Valve Seat Material H 17-4 Stainless Steel N Nitronic 5 T Hastelloy C 9 Valve Material F 17-4 Stainless Steel N Nitronic 5 T Hastelloy C 1 Valve Springs E Elgiloy H 17-7 Stainless Steel 11 Valve Spring Retainers C Celcon M PVDF P Polypropylene 12 Hydra-Oil A 1W3 standard-duty oil H 15W5 high-temp severe-duty synthetic oil 7 www.hydra-cell.eu
WANNER Partners in over 7 Countries WANNER ENGINEERING - WORLD HEADQUARTERS & MANUFACTURING Minneapolis USA t: (612) 332-5681 e: sales@wannereng.com WANNER PUMPS Kowloon HONG KONG t: +852 3428 6534 e: sales@wannerpumps.com WANNER ENGINEERING Latin American Office t: +55 (11) 481-798 e: sales@wannereng.com WANNER PUMPS Shanghai CHINA t: +86-21-6876 37 e: sales@wannerpumps.com WANNER INTERNATIONAL Hampshire UK t: +44 () 1252 816847 e: sales@wannerint.com www.hydra-cell.eu