INSTALLATION INSTRUCTIONS Accessory S P/N 08L02-TK8-100 Application 2014 ODYSSEY Publications No. AII 49541 Issue Date JUNE 2013 PARTS LIST 12 Torx nuts Left side roof rail 4 Torx screws Right side roof rail 2 Roof molding clips Left front roof rail cover Right front roof rail cover Left center roof rail cover TOOLS AND SUPPLIES REQUIRED Tape measure Needle nose pliers T-15 and T-30 Torx drivers Eye protection (face shield, safety goggles, etc.) File Felt-tip pen Masking tape The following tools are available through the Honda Tool and Equipment Program. On the in, click on: Service > Service Bay > Tool and Equipment Program, then enter the number under Search. Or, call 888-424-6857. Trim Tool Set (T/N SOJATP2014) Air Saw (T/N AT192A) Right center roof rail cover Left rear roof rail cover Right rear roof rail cover 2013 American Honda Motor Co., Inc. All Rights Reserved. AII 49541 (1306) 08L02-TK8-1001-91 1 of 6
Illustration of the Roof Rails Installed on the Vehicle RIGHT SIDE 2. Open the tailgate halfway. Using a trim tool, pry up on the rear end of the roof molding left cover. LEFT TAILGATE (Open the halfway.) 020101AB INSTALLATION Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by do-it-yourselfers. NOTE: Be extremely careful not to damage the roof and other finished surfaces of the body when installing the roof rails. TRIM TOOL 020102AB 3. While wearing an eye protection, use an air saw to cut off the roof molding left cover at the scribe line as shown. Remove any burrs. SCRIBE LINE Installing the Roof Rails 1. Remove the left roof molding by carefully lifting it upward from four roof molding clips. 4 CLIPS LEFT AIR SAW 020103AB 020104BB 2 of 6 AII 49541 (1306) 2013 American Honda Motor Co., Inc. All Rights Reserved.
4. Remove and discard four roof molding clips from the roof molding or the stud bolt on the roof. 6. Measure and use a felt-tip pen to mark the left roof molding as shown. CLIPS (Discard.) CLIPS (Discard.) ROOF 518 mm (20.4 in.) 95 mm (3.7 in.) 850 mm (33.5 in.) MARK STUD BOLT 150 mm (5.9 in.) 556 mm (21.9 in.) FELT-TIP PEN 042701BB 7. While wearing an eye protection, use an air saw to cut off the left roof molding at the mark made in step 6. 020105AB MARK 5. Remove any excess sealant from the stud bolts. STUD BOLT STUD BOLT SEALANT SEALANT (Remove the excess.) AIR SAW 020107BB QC30702AB 2013 American Honda Motor Co., Inc. All Rights Reserved. AII 49541 (1306) 3 of 6
8. Install one roof molding clip to the left roof molding (front). 10. Reinstall the left roof moldings back onto the roof of the vehicle as shown. CENTER SIDE (Make sure to install in the correct direction.) CENTER SIDE (Make sure to install in the correct direction.) () OUTSIDE OUTSIDE CLIP CLIP () QC30703AB S QC30704AB 9. Reinstall the roof molding left cover. NOTE: If the roof molding cover is not even with the roof, it is installed incorrectly. Reinstall the roof molding cover properly. LEFT TAILGATE 11. Install the left side roof rail with six Torx nuts. Make sure the roof rail is installed in the correct position. Torque the Torx nuts to: 10 N m (1.0 kgf m, 7.3 lbf ft) 6 TORX NUTS 020109AB 6 STUD BOLTS 020111BB 4 of 6 AII 49541 (1306) 2013 American Honda Motor Co., Inc. All Rights Reserved.
12. Install the left front roof rail cover to the left side roof rail with two clips. TORX SCREW 2 CLIPS 16. Attach the masking tapes to the vehicle panel. LEFT MASKING TAPES 020112BB 13. Secure the left front roof rail cover to the left side roof rail with one Torx screw. VEHICLE PANEL 061802AB 17. Hook the left center roof rail cover to the left side roof rail as shown. 14. Install the left rear roof rail cover to the left side roof rail with three clips. LEFT REAR TORX SCREW 3 CLIPS 020113BB LEFT CENTER 020114BB 15. Secure the left rear roof rail cover to the left side roof rail with one Torx screw. 2013 American Honda Motor Co., Inc. All Rights Reserved. AII 49541 (1306) 5 of 6
18. Install the left center roof rail cover to the left side roof rail as shown. Make sure that the left center roof rail cover is no clearance between the left side roof rail. VIEWED FROM INSIDE LEFT CENTER Push. Turn. LEFT CENTER 061803AB 19. Remove the masking tapes attached in step 16. 20. Repeat steps 1 through 19 for the right side of the vehicle. USE AND CARE Check the roof rail mounting bolts frequently, and re-tighten if necessary. 6 of 6 AII 49541 (1306) 2013 American Honda Motor Co., Inc. All Rights Reserved.