BM20200 Mobile Roller Brake Tester The BM20200 roller brake tester is designed for direct on-ground installation without need of civil work. It requires only approximately 10 minutes for one person to set it up for operation. This brake tester features a large range of options that allows for a customized configuration. OPTIONS Robust and long lasting: All steel is of highest quality and hot galvanized. Consists of an integral motorized gear box, two main rollers and a spring loaded sensor roller, all placed in a galvanized steel frame. The wear surfaces of the rollers are based on mesh steel to ensure a long life time and accurate measurements. Steel mesh plus a flinstone/bauxite mix for test of only summer tires.
Steel mesh for test of winter tires (spike tires) and summer tires. Can be supplied in a minimum configuration and still allows for later upgrade to all options. Easy to use with BM software: Integrated guide. Advanced graphics printout. Diagnostic printout with or without connection to PC/Notebook. Calculation of test results according to the requirements of many national authorities. BM FlexCheck software: Advanced data collection, storing and presentation of test results. Data capture from a complete inspection lane. PDA/smartphone/tablet solution that allows the operator to control and monitor the test results directly on a handheld unit. BM FlexCheck on smartphone and tablet Infrared remote control with an operating distance of 15-25 metres.. Large and easy-to-read aluminium display with analogue and digital readout of all relevant test
data. Integrated guide. Large analogue dials showing readings of left and right brake forces. 65 mm high bright digital readouts of other measurement results. Modularly designed so that it can be customized to existing and future demands. Display units are available in dan, kgf or kn. Up to 3 displays can be connected. Optional automatic axle weighing and vehicle total weight. Test of 4 4, 6 4 and 8 6 driven vehicles. Optional cable or radio pedal force meter. Optional cable or radio air/hydraulic pressure system. Posibility to create a mobile test lane concept consisting of: BM53000 mobile wheel play detector BM605 tacho tester Optional axle load simulation. BM ALS axle load simulation
Optional transport solutions: Trailer solution. Inside 20 container. The BM20200 roller brake tester is approved by several international authorities and can optionally be supplied in compliance with ISO 21069. See also other BM brake testers for light and heavy vehicles: BM12200, BM14200, BM17200 and BM5200. Advantages IT system using the latest app technology for smartphone and tablet (Windows and Android). The rollers are only approximately 160 mm above floor level allowing for very short drive on/off ramps (only 125 cm on each side). Requires a minimum of floor space. Total weight of only approximately 1200 kg. Can be supplied with wheels and trolley for easy manuovering. Compact design during transport with drive on/off ramps folded up and display placed between left and right side roller bed. Can be made operational by one person in approximately 10 minutes. Installation
Placed directly on the floor indoor or outdoor without need of civil work. Can be installed as split bed over an inspection pit. No particular requirements to the testing area surface (asphalt, concrete, gravel, sand, dirt etc.) Can be installed both indoor and outdoor in most environments from -30ºC to 60 C and humidity up to 95. Applications Normal workshops for repair and test of light and heavy vehicles.
Perfect for road side inspections by enforcement authorities due to low weight and height. Works well in tough environments as experienced by army, navy and air force organisations. Can be placed directly on-ground on locations such as indoor and outdoor repair workshops, laybys at highways, port entry areas, gravel ground at remote areas etc.
Downloads BM20200 brochure EN (PDF) BM20200 brochure DA (PDF) BM20200 brochure ES (PDF) BM20200 brochure SE (PDF) BM20200 brochure NO (PDF) Videos BM20200 mobile brake tester BM20200 is a mobile brake tester for light and heavy vehicles with an axle load of up to 20.000 kg. Mobile brake tester installation BM20200 A V-Tech installation of a BM20200 Mobile roller brake tester for Omega Travel. A great workshop solution to test the fleet s braking systems without the need for civil works and to keep the workshop space flexible.
Unloading a BM20200 mobile roller brake tester Unloading a BM20200 mobile roller brake tester in less than 10 minutes. This video was made by BM distributor in USA, LINK Engineering. Full brake test on BM20200 Conducting a brake test on a BM20200. This video was made by BM distributor in USA, LINK Engineering. Roller brake test of agricultural vehicles Danish. A film about brake testing of agricultural vehicles made by BM Autoteknik in association with the Danish Færdselsgruppen (Traffic Group). Roller brake test of agricultural vehicles Danish with English subtitles. A film about brake testing of agricultural vehicles made by BM Autoteknik in association with the Danish Færdselsgruppen (Traffic Group). Tractor testing on Bremsedagen 2011 Danish. BM Autoteknik tested tractor train using BM25 SmartTest. Product Short Description :
Mobile roller brake tester for vehicles with axle load up to 20000 kg. Additional Information: Dimensions: N/A Weight: 1250 kg Roller bed per side (1000 mm rollers) LxWxH: 3465 x 4240 x 505 mm Roller bed per side (1250 mm rollers) LxWxH: 3465 x 4740 x 505 mm Roller bed per side (1600 mm rollers) LxWxH: 3465 x 5440 x 505 mm Roller diameter: 150 mm Roller length: 1000 mm, 1250 mm, 1600 mm Friction coefficient of roller from factory dry/wet: Min. 0.7/0.6 Wheel span: 800 to 2800/3300/4000 mm Distance between roller centres: 430 mm Maximum test axle weight: 16000 kg, 20000 kg Gear motor size: 2.2 kw, 4.8 kw, 11 kw, 15 kw Max. brake force measurement: 4000 dan, 6000 dan Test speed: 0.5 km/h, 1.0 km/h, 2.0 km/h, 3.0 km/h Display (LxWxH): 930 x 820 x 100 mm Control box (LxWxH): 600 x 600 x 210 mm Display brake force scale: 0 800 dan, 0 4000 dan Brake force measuring accuracy: 0 100 dan: +/-2 dan, > 100 dan: +/-2% FS Pedal force measuring accuracy: 0 100 dan: +/-1 dan Power and fuses: 3 x 400 Vac + N + PE, Min. 16/25/50/80 Amp, 3 x 230 Vac + PE, Min. 20/50/80/125 Amp Product Gallery: