Steady-State and Transient Simulation of Gas Flow Pressure in Intake Port Engine

Similar documents
Heat Transfer Investigation of Intake Port Engine Based on Steady-State and Transient Simulation

Engine Cylinder Fluid Characteristics of Diesel Engine Converted to CNG Engine

Air Flow Analysis of Four Stroke Direct Injection Diesel Engines Based on Air Pressure Input and L/D Ratio

Investigation of Fuel Flow Velocity on CNG Engine using New Injector

A STUDY ON DIESEL ENGINE PERFORMANCE DEPENDS ON BP AND BSFC BY APPLYING DIFFERENT INJECTION PRESSURE

Fuel Injection Pressure Effect on Performance of Direct Injection Diesel Engines Based on Experiment

Investigation of Diesel Engine Performance Based on Simulation

INFLUENCE OF THE NUMBER OF NOZZLE HOLES ON THE UNBURNED FUEL IN DIESEL ENGINE

The Effect of Spring Design as Return Cycle of Two Stroke Spark Ignition Linear Engine on the Combustion Process and Performance

INTAKE VALVE LIFT EFFECT ON AIR-FUEL MIXING OF DUAL FUEL ENGINE

Gas exchange and fuel-air mixing simulations in a turbocharged gasoline engine with high compression ratio and VVA system

Crankcase scavenging.

The Effect of Efi to the Carbureted Single Cylinder Four Stroke Engine

II. EXPERIMENTAL SETUP AND PROCEDURE

Influence of Fuel Injector Position of Port-fuel Injection Retrofit-kit to the Performances of Small Gasoline Engine

Simulation of Performance Parameters of Spark Ignition Engine for Various Ignition Timings

DESIGN OF THROTTLE BODY: A COMPARATIVE STUDY OF DIFFERENT SHAFT PROFILES USING CFD ANALYSIS

NUMERICAL INVESTIGATION OF EFFECT OF EXHAUST GAS RECIRCULATION ON COMPRESSIONIGNITION ENGINE EMISSIONS

Prediction Studies for the Performance of a Single Cylinder High Speed Spark Ignition Linier Engine with Spring Mechanism as Return Cycle

Influence of Cylinder Bore Volume on Pressure Pulsations in a Hermetic Reciprocating Compressor

Comparing FEM Transfer Matrix Simulated Compressor Plenum Pressure Pulsations to Measured Pressure Pulsations and to CFD Results

SWIRL MEASURING EQUIPMENT FOR DIRECT INJECTION DIESEL ENGINE

CONTROLLING COMBUSTION IN HCCI DIESEL ENGINES

DEVELOPMENT OF COMPRESSED AIR POWERED ENGINE SYSTEM BASED ON SUBARU EA71 MODEL CHEN RUI

REDUCTION OF EMISSIONS BY ENHANCING AIR SWIRL IN A DIESEL ENGINE WITH GROOVED CYLINDER HEAD

TECHNICAL PAPER FOR STUDENTS AND YOUNG ENGINEERS - FISITA WORLD AUTOMOTIVE CONGRESS, BARCELONA

The Effect of Spark Plug Position on Spark Ignition Combustion

Effect of Helix Parameter Modification on Flow Characteristics of CIDI Diesel Engine Helical Intake Port

Study of intake manifold for Universiti Malaysia Perlis automotive racing team formula student race car

GT-Power Report. By Johan Fjällman. KTH Mechanics, SE Stockholm, Sweden. Internal Report

Comparison of Air-Standard Atkinson, Diesel and Otto Cycles with Constant Specific Heats

System Simulation for Aftertreatment. LES for Engines

[Rao, 4(7): July, 2015] ISSN: (I2OR), Publication Impact Factor: 3.785

Marc ZELLAT, Driss ABOURI and Stefano DURANTI CD-adapco

PERFORMANCE EVALUATION OF A FOUR STROKE COMPRESSION IGNITION ENGINE WITH VARIOUS HELICAL THREADED INTAKE MANIFOLDS

Analysis of Parametric Studies on the Impact of Piston Velocity Profile On the Performance of a Single Cylinder Diesel Engine

DISCHARGE AND FLOW COEFFICIENT ANALYSIS IN INTERNAL COMBUSTION ENGINE USING COMPUTATIONAL FLUID DYNAMICS SIMULATION

An Experimental investigation of dimpled inlet valve on Diesel engine performance

Flow Simulation of Diesel Engine for Prolate Combustion Chamber

Finite Element Analysis on Thermal Effect of the Vehicle Engine

EXHAUST BRAKE SYSTEM MODEL AND TORQUE SIMULATION RESULTS ON A DIESEL SINGLE-CYLINDER ENGINE

COLD FLOW ANALYSIS OF A SINGLE CYLINDER FOUR STROKE DIRECT INJECTION CI ENGINE AND ANALYSIS OF VOLUME FRACTION OF AIR USING CFD TECHNIQUE

Transient in-cylinder Gas Flow Characteristics of Single Cylinder Port Injection Hydrogen Fueled Engine

Potential of Large Output Power, High Thermal Efficiency, Near-zero NOx Emission, Supercharged, Lean-burn, Hydrogen-fuelled, Direct Injection Engines

EFFECT OF INJECTION ORIENTATION ON EXHAUST EMISSIONS IN A DI DIESEL ENGINE: THROUGH CFD SIMULATION

A REVIEW OF SCAVENGING PROCESS OF TWO STROKE ENGINE

MARINE FOUR-STROKE DIESEL ENGINE CRANKSHAFT MAIN BEARING OIL FILM LUBRICATION CHARACTERISTIC ANALYSIS

Application of Natural Gas for Internal Combustion Engines

2013 THERMAL ENGINEERING-I

Homogeneous Charge Compression Ignition combustion and fuel composition

H. Sumithra Research Scholar, School of mechanical Engineering RGMCET, Nandyal, Andhra Pradesh, India.

Experimental Investigation on Modification of Inlet poppet valve of single cylinder Direct Ignition Four stroke Diesel Engine

Comparative performance and emissions study of a lean mixed DTS-i spark ignition engine operated on single spark and dual spark

Comparison of Swirl, Turbulence Generating Devices in Compression ignition Engine

Heat Release Model of DI Diesel Engine: A Review

Eco-diesel engine fuelled with rapeseed oil methyl ester and ethanol. Part 3: combustion processes

Effect of concave plug shape of a control valve on the fluid flow characteristics using computational fluid dynamics

Numerical Simulation of the Effect of 3D Needle Movement on Cavitation and Spray Formation in a Diesel Injector

Engine Manifold Wave Action under Variable Stroke Length

Smoke Reduction Methods Using Shallow-Dish Combustion Chamber in an HSDI Common-Rail Diesel Engine

Thermo-Kinetic Model to Predict Start of Combustion in Homogeneous Charge Compression Ignition Engine

[Rohith, 5(1): January, 2016] ISSN: (I2OR), Publication Impact Factor: 3.785

POSIBILITIES TO IMPROVED HOMOGENEOUS CHARGE IN INTERNAL COMBUSTION ENGINES, USING C.F.D. PROGRAM

NUMERICAL INVESTIGATION OF PISTON COOLING USING SINGLE CIRCULAR OIL JET IMPINGEMENT

Christof Schernus, Frank van der Staay, Hendrikus Janssen, Jens Neumeister FEV Motorentechnik GmbH

Numerical Study on the Flow Characteristics of a Solenoid Valve for Industrial Applications

Generation of Air Swirl through Inlet Poppet Valve Modification and To Enhance Performance on Diesel Engine

Thermal Stress Analysis of Diesel Engine Piston

A Novel Device to Measure Instantaneous Swept Volume of Internal Combustion Engines

Effects of ethanol unleaded gasoline blends on cyclic variability and emissions in an SI engine

AN ANALYSIS OF EFFECT OF VARIABLE COMPRESSION RATIO IN C.I. ENGINE USING TURBOCHARGER

837. Dynamics of hybrid PM/EM electromagnetic valve in SI engines

Figure 1: The Turbocharger cross-section with turbine and compressor connected with shaft [2]

Transient Thermal Analysis of Screw Compressors, Part III: Transient Thermal Analysis of a Screw Compressor to Determine Rotor-to-Rotor Clearances

Gas exchange Processes. Typical valve timing diagram

Assignment-1 Introduction

PERFORMANCE AND COMBUSTION ANALYSIS OF MAHUA BIODIESEL ON A SINGLE CYLINDER COMPRESSION IGNITION ENGINE USING ELECTRONIC FUEL INJECTION SYSTEM

Study on Flow Fields in Variable Area Nozzles for Radial Turbines

GT-Suite Users International Conference Frankfurt a.m., October 22 nd 2012

CFD ANALYSIS ON LOUVERED FIN

Design Rules and Issues with Respect to Rocket Based Combined Cycles

PM Emissions from HCCI Engines

Unit WorkBook 4 Level 4 ENG U13 Fundamentals of Thermodynamics and Heat Engines UniCourse Ltd. All Rights Reserved. Sample

Effect of cavitation in cylindrical and twodimensional nozzles on liquid jet formation

SIX STROKE ENGINE ARRANGEMENT

CFD Analysis for Designing Fluid Passages of High Pressure Reciprocating Pump

Aguk Zuhdi Muhammad Fathallah 1, Wolfgang Busse 2, Fadhil Rizki Clausthaldi 3

Vol-3 Issue India 2 Assistant Professor, Mechanical Engineering Dept., Hansaba College of Engineering & Technology, Gujarat, India

Analysis of Emission characteristics on Compression Ignition Engine using Dual Fuel Mode for Variable Speed

Electromagnetic Fully Flexible Valve Actuator

Australian Journal of Basic and Applied Sciences

Marc ZELLAT, Driss ABOURI, Thierry CONTE and Riyad HECHAICHI CD-adapco

Practical Exercise: Computation of the engine output characteristics for a 4-stroke spark ignition engine

Direct Injection Ethanol Boosted Gasoline Engines: Biofuel Leveraging For Cost Effective Reduction of Oil Dependence and CO 2 Emissions

Numerical Study on the Combustion and Emission Characteristics of Different Biodiesel Fuel Feedstocks and Blends Using OpenFOAM

Studying Turbocharging Effects on Engine Performance and Emissions by Various Compression Ratios

Improving Simulation Accuracy of a Downsized Turbocharged SI Engine by Developing a Predictive Combustion Model in 1D Simulation Software

Investigation of Radiators Size, Orientation of Sub Cooled Section and Fan Position on Twin Fan Cooling Packby 1D Simulation

THE THEORETICAL STUDY ON INFLUENCE OF FUEL INJECTION PRESSURE ON COMBUSTION PARAMETERS OF THE MARINE 4-STROKE ENGINE

Computational Investigation of Normal and Hybrid Cooling Fins of Internal Combustion Engine

Transcription:

Journal of Engineering and Applied Sciences 3 (1): 47-54, 008 ISSN: 1816-949X Medwell Journals, 008 Steady-State and Transient Simulation of Gas Flow Pressure in Intake Port Engine 1 Semin, Abdul Rahim Ismail and Rosli Abu Bakar 1 Institute of Technology Sepuluh Nopember, Surabaya 60111, Indonesia Faculty of Mechanical Engineering, University Malaysia Pahang, 5000 Kuantan, Malaysia Abstract: This study presents the gas flow pressure in the intake port of four-stroke direct-injection compression ignition engine using GT-Suite software for steady-state and transient simulation. To investigate and simulate the intake port gas flow pressure profile of compression ignition engine is using GT-Power engine model were developed in this study. GT-Power is sub-system menu from GT-Suite. The engine model is developed from the real compression ignition engine data and input to software library. In this research, the simulation of engine model is running in variations engine speeds. The simulation output data is collected from the GT-Post results plots and cases RLT in post processing. The simulation results of the intake port engine model are shown the characters in intake port pressure profile of engine in variations engine speeds. The detail performance intake port gas flow pressure is shown in graphs in this study. Key words: Compression ignition engine, computational model, intake port, pressure, simulation INTRODUCTION thermodynamics performance using GT-Suite simulation model, how the engine model developed and how the The compression ignition engine performance theory components interact. to link together with computer modeling of the engine The direct injection compression ignition engines is thermodynamics in engine simulations are great challenge, internal combustion engines, where fuel is injected by the as the latter make the most complete use of the former and fuel injection system into the engine cylinder toward the the use models is becoming widespread. Engine modeling end of the compression stroke, just before the desired is a very large subject, in part because of the range of start of combustion (Bakar and Semin, 006a, b; engine configurations possible and the variety of Bakar et al., 007a; Kowalewicz, 1984; Stone, 1997; alternative analytical techniques or sub-models, which Heywood, 1998; Ganesan, 1999; Challen and Baranescu, can be applied in overall engine models (Challen and 003). The liquid fuel, usually injected at high velocity as Baranescu, 003). Engine modeling is a fruitful research one or more jets through small orifices or nozzles in area and as a result many universities have produced their injector tip, atomizes into small drops and penetrates into own engine thermodynamics models, of varying degrees the combustion chamber. The fuel vaporizes and mixes of complexity, scope and ease to use. There are also now with high temperature and high pressure cylinder air. The available a number of fairly comprehensive models which air is supplied from intake port of engine. Since the air have a wider, more general purpose use with refined temperature and pressure are above the fuel s ignition inputs and outputs to facilities their use by engineers point, spontaneous ignition of portions of the alreadyother than their developers, most of these models had mixed fuel and after air a delay period of a few crank angle their origins in university-developed models. They degrees. The cylinder pressure increases as combustion include WAVE from USA, PROMO from Germany, of the fuel-air mixture occurs (Atkinson and Andersson, TRANSEG/ICENG/MERLIN from UK, among others. A 1999; Eriksson et al., 00; Klein et al., 00; Piedrahita new code covering completes engine systems have et al., 003; Sanders et al., 003). The major problem in emerged recently, GT-Suite (Challen and Baranescu, compression ignition engine combustion chamber design 003). is achieving sufficiently rapid mixing between the injected In this study, the steady-state and transient of gas fuel and the air from intake port in the cylinder to complete flow in intake port of engine is simulate using GT-Suite. combustion in the appropriate crank angle interval close This research is focuses on single cylinder four stroke to top-center (Bakar and Semin, 006a; Baker et al., 007a; direct injection compression ignition engine. The aim is Blair, 1999; Challen and Baranescu, 003; Heywood, to give an insight into the engine intake port gas flow 1998; Ganesan, 1999; Klein et al., 00; Semin et al., Corresponding Author: Semin, Center for Graduate Studies, University Malaysia Pahang, Locked Bag 1, 5000 Kuantan, Pahang, Malaysia 47

J. Eng. Applied Sci., 3 (1): 47-54, 008 007a). Horsepower output of an engine can be dramatically improved through good intake port design and manufacture (Jawad et al., 003). To determine gas flow conditions right through the engine is the essence of modeling at small intervals time. Appropriate summation of these gas conditions over an engine cycle then leads to an estimate engine performance. Gas flow condition through the engine is basically meant pressures, temperatures, gas composition and mass or energy flows. The core of any model is the energy equation for each control volume in the engine (Challen and Baranescu, 003). The first essential the engine performance model is the energy for a control volume, which is derived from First Law Thermodynamics and the Perfect Gas Law. The first law states that the rate of change of internal energy of the volume from connected gas flows, less any nett heat transfer out through the volume walls and less any work done by the control volume gas against its surroundings is shown in Eq. 1. ( ) d um dq dv dt dt dt = hm i i P l Where u is the specific internal energy per unit mass of gas in the control volume and there are l pipes connecting to the control volume, the flow in the ith pipe having specific enthalpy hi and mass flow rate m i (negative for outflow). Net heat transfer out of the control volume is dq/dt, M is the mass of gas in the control volume at pressure P and this gas carrier out nett work on its surroundings of PdV/dt, where dv/dt is the control volume s current rate of change of volume (zero for manifold control volume and not for cylinder control volume). To determine flow through a pipe and constriction is needed the orifice equation. The stagnation or total temperature T t at any point in a flow is given by Eq.. v ct p t = ct p + Where, T t is the temperature that the gas flowing at velocity v with static temperature T would reach if it were brought to rest adiabtically, the equation is simply an energy balance, cpt being a measure of the static energy, v / the kinetic energy and cptt the total energy (enthalpy). And to determine the mach number Ma is using Eq. 3, where c is velocity of sound, ( is equal with cp/cv and cp-cv = R. (1) () v v Ma = = c RT p ( γ ) The total to static temperature relationship is obtained using Eq. 4 and 5. Then the total to static pressure equation is shown in Eq. 6. Tt v γrtm = 1+ = 1+ T c c a Tt M = 1+ ( γ 1) T p a γ γ γ 1 1 γ γ 1 Ma Pt Tt 1 = = + P T MATERIALS AND METHODS The real engine data is used in four stroke single cylinder direct injection compression ignition engine model. The model of compression ignition engine has been developed using GT-POWER software based from real engine selected data. According to Bakar and Semin (006a), Baker et al. (007b, c), Ismail et al. (007), Semin et al. (007a), Baker and Semin (007b-d) the specification of four stroke direct injection compression ignition engine and it intake port is shown in Table 1 and the physical illustration of intake port is shown in Fig. 1. According to Bakar et al. (007b, c) and Semin et al. (007a, c) in the GT-POWER engine model development, a typical intake port is modeled using Import, engine is modeled using EngCylinder and EngineCrankTrain component objects, Valve*Conn and EngCylConn connection objects. Import is used to define the basic geometry and characteristics of intake port, EngCylinder and EngineCranktrain are used to define the basic geometry and characteristics of engine. These objects further refer to several reference objects for more detailed modeling information on such attributes as gas flow, combustion and heat transfer. Import must be connected to the engine cylinder with Valve*Conn, Cylinder must be connected to the engine with EngCylConn part made from the predefined object which available in the template library. While Pipe, EngCylConn parts have no user defined attributes, the global cylinder number for cylinder is assigned by the port number where the EngCylConn connection is attached to the engine. Cylinder are connected to intake and exhaust ports with Valve*Conn connections. Many Valve*Conn connection (3) (4) (5) (6) 48

J. Eng. Applied Sci., 3 (1): 47-54, 008 Table 1: Specification the engine and intake port Engine and intake parameters Value Bore (mm) 86.0 Stroke (mm) 70.0 Displacement (cc) 407.0 Number of cylinder 1 Connecting rod length (mm) 118.1 Exhaust Valve Open (EVO) ( CA) 147 Exhaust Valve Close (EVC) ( CA) 8 Intake Valve Open (IVO) ( CA) 395 Intake Valve Close (IVC) ( CA) 530 Injection Start ( CA) -.0 Combustion start ( CA) -1.0 Number of nozzle injector 1 Number of nozzle injector holes 4 Diameter of nozzle injector holes (mm) 0.1 Intake port diameter inlet end (mm) 40.69 Intake port diameter outlet end (mm) 3.78 Intake port length (mm) 55. Intake port discreatization length (mm) 34.4 Intake port wall temperature ( C) 176.85 D.inlet Fig. : Single cylinder compression ignition engine model using GT-POWER, i-9 is intake port Fig. 1: Intake port of engine D.outlet templates are available to define different types of valve, port and their characteristics. To create the GT-POWER model, open the GT- SUITE software and select the GT-POWER menu, select window and then Tile with Template Library from the menu. This will place the GT-POWER template library on the left hand side of the screen. The template library contains all of the available templates that can be used in GT-POWER. Some of these templates those that will be needed in the project need to be copied into the project before they can be used to create objects and parts. For the purpose of this model, click on the icons listed and drag them from the template library into the project library. Some of these are templates and some are objects that have already been defined and included in the GT- POWER template library. Then, the engine components size data input to the GT-POWER library of the all engine components data. All of the parameters in the model will be listed automatically in the case setup and each one must be defined for first case of the simulation. The engine model is shown in Fig.. In this research, the solver of GT-POWER determines the performance of an engine simulation based on engine speed mode in the EngineCrankTrain object. Speed mode is the most commonly used mode of engine simulation, especially for steady states cases (Gamma Technologies, 003). In the research imposes the engine speed as either constant or by a dependency reference object. This method typically provides steady-state results very quickly because the speed of the engine is imposed from the start of the simulation, thus eliminating the relatively long period of time that a loaded engine requires for the crankshaft speed to reach steady-state. RESULTS AND DISCUSSION The simulation of the four stroke direct injection compression ignition engine model is running in 8 cases engine speed. Case 1 is engine model running at 500 rpm, case is engine model running at 1000 rpm, case 3 is engine model running at 1500 rpm, case 4 is engine model running at 000 rpm, case 5 is engine model running at 500 rpm, case 6 is engine model running at 3000 rpm, case 7 is engine model running at 3500 rpm and case 8 is engine model running at 4000 rpm. In this research, the result of the model is viewed from GT-Post plots and casesrlt. GT-Post plots result is intake port static pressure versus crank angle degree based on engine speed and GT-Post cases RLT result is intake port pressure versus engine speed based on any cases. 49

J. Eng. Applied Sci., 3 (1): 47-54, 008 Fig. 3: Intake port static pressure at 500 RPM Fig. 5: Intake port static pressure at 1500 RPM Fig. 4: Intake port static pressure at 1000 RPM The results of the simulations from GT-Post plots are shown in Fig. 3-10. The results from the GT-Post plots investigation are focuses on inlet port static pressure. Figure 3 shows the intake port static pressure versus crank static pressure versus crank angle profile at 1500 RPM engine speeds, Fig. 6 shows the intake port static pressure versus crank angle profile at 000 RPM engine speeds, Fig. 7 shows the intake port static pressure versus crank angle profile at 500 RPM engine speeds, Fig. 8 shows the intake port static pressure versus crank angle profile at 3000 RPM engine speeds, Fig. 9 shows the intake port static pressure versus crank angle profile at 3500 RPM engine speeds and Fig. 10 shows the intake port static pressure versus crank angle profile at 4000 RPM engine speeds. The static pressures characteristics in intake port profile of four stroke direct injection compression ignition engine is shown in Fig. 3-10. The results have been plotted from simulation result output of GT-Post plots. Figure 3-10 shows the profile of the minimum and the Fig. 6: Intake port static pressure at 000 RPM maximum intake port static pressure versus crank angle profile at 500-4000 RPM engine speeds in compression stroke, power stroke, exhaust stroke and intake stroke of engine. In this engine speed, nominal static pressure in the intake stroke is most extreme then in the compression stroke compare with power stroke and exhaust stroke. In the intake stroke is started from static pressure when the intake valve is just start opened, so the pressure not extreme different compare with another stroke. In the intake valve opened the static pressure is increase extremely because in the stroke the cylinder is needed suction air into the engine cylinder to mixture with fuel for engine combustion to angle profile at 500 RPM engine speeds, Fig. 4 shows the intake port static pressure versus crank angle profile at 1000 R PM engine speeds, Fig. 5 shows the intake port product the power. In the intake valve closed processing until intake valve is closed the pressure static is very low because in this process the gas flow in the intake port is crass with back static pressure from intake valve closed. Then the static pressure is become to lower and lower in 50

J. Eng. Applied Sci., 3 (1): 47-54, 008 Fig. 7: Intake port static pressure at 500 RPM Fig. 10: Intake port static pressure at 4000 RPM Fig. 8: Intake port static pressure at 3000 RPM Fig. 11: Maximum pressure inlet at intake port Fig. 9: Intake port static pressure at 3500 RPM compression stroke, power stroke and in exhaust stroke is the lowest. In the intake stroke, the highest static pressure is declared in 3500RPM engine speed and shown Fig. 1: Minimum pressure inlet at intake port in Fig. 9, because in this engine speed the combustion is excellent dramatically so need most of air to combustion process and the minimum static pressure is in 4000 RPM engine speed and shown in Fig. 10, because in this engine 51

J. Eng. Applied Sci., 3 (1): 47-54, 008 Fig. 13: Average total pressure inlet at intake port Fig. 15: Minimum pressure outlet at intake port Fig. 14: Maximum pressure outlet at intake port Fig. 16: Average total pressure outlet at intake port speed investigation the combustion and the intake valve speed and Fig. 18 shows the outlet pressure at end of lift and intake valve close moving is most quickly so the cycle at intake port on 500-4000 RPM engine speed. air flow back static pressure from the intake valve closing The pressure performance characteristics of intake is highest than the other engine speed. port engine in any cases shown in Fig 11-18. The Fig. 11 The results of the simulations from GT-Post shows that the inlet maximum pressure to the intake port casesrlt are shown in Fig. 11-18. The results from the from the intake runner the highest is in 3500RPM engine GT-Post casesrlt investigation are focuses on any cases speed, likely the static pressure in 3500RPM the in intake port pressure. Figure 11 shows the maximum combustion is most excellently so the engine cylinder is pressure inlet at intake port on 500-4000 RPM engine needed most air volume for in cylinder combustion speed, Fig. 1 shows the minimum pressure inlet at intake process. The Fig. 1 shows that the minimum inlet port on 500-4000 RPM engine speed, Fig. 13 shows the pressure to intake port the lowest is in 4000 RPM engine average total pressure inlet at intake port on 500-4000 speed, because in the engine speed the combustion and RPM engine speed, Fig. 14 shows the maximum pressure the intake valve opened and closed is most quickly. It can outlet at intake port on 500-4000 RPM engine speed, be the back flow of air from cylinder and intake valve Fig. 15 shows the minimum pressure outlet at intake port closed is very high. The air back flow pressure can be on 500-4000 RPM engine speed, Fig. 16 shows the reduced the intake pressure inlet to intake port. The outlet average total pressure outlet at intake port on 500-4000 maximum pressure from the intake port to the engine RPM engine speed, Fig. 17 shows the inlet pressure cylinder is shown in Fig. 14. The highest maximum outlet at end of cycle at intake port on 500-4000 RPM engine pressure is in 3500 RPM engine speed, in 3500 RPM 5

J. Eng. Applied Sci., 3 (1): 47-54, 008 intake port to engine cylinder is in 500RPM engine speed. The pressure at end of cycle at intake port is shown in Fig. 17 and 18. Figure 17 is shows the intake pressure at end of cycle at intake port and Fig. 18 shows the outlet pressure at end of cycle at intake port. The highest inlet and outlet pressure at end of cycle at intake port is in 1500 RPM engine speed and the lowest inlet and outlet pressure at end of cycle at intake port is in 4000 RPM. It mean that in 1500 RPM engine speed the back flow pressure is lowest and in 4000 RPM engine speed the back flow pressure is highest. CONCLUSION Fig. 17: Inlet pressure at end of cycle at intake port Intake port pressure versus crank angle and engine speed data can be used to obtain quantitative information to predict the characteristics of the intake port gas flow pressure were needed on the progress of combustion. The simulation results are shown that the highest intake port static pressure is in 3000 RPM, the highest outlet pressure intake pressure to the engine cylinder is in 3500 RPM and the lowest outlet pressure intake port to engine cylinder is in 4000 RPM engine. The simulation result shown the optimum pressure in intake port is if the engine operated in 3000-3500 RPM. If the engine is operated higher than 3500 RPM it can be highest back flow pressure. REFERENCES Fig. 18: Outlet pressure at end of cycle at intake port Atkinson, M. Christopher, Thompson, J. Gregory, Traver, Michael, L., Clark and N. Nigel, 1999. In-cylinder engine speed the combustion is most excellently so the combustion pressure characteristics of Fischerengine cylinder is needed most air volume for in cylinder Tropsch and conventional diesel fuels in a heavycombustion process, so the engine need most pressure duty CI engine. SAE Paper 1999-01-147. and volume compare the other speed. The minimum outlet Blair and P. Gordon, 1999. Design and Simulation of Four pressure from intake port to engine cylinder the lowest is Stroke Engines. SAE Inc. USA. in 4000RPM engine speed too, because in the engine Challen, B. and R. Baranescu, 003. Diesel Engine speed the combustion and the intake valve opened and Reference Book, Elsevier, Oxford, U.K. closed is most quickly. It can be the back flow of air from Eriksson, L. and I. Andersson, 00. An analytic model for cylinder and intake valve closed is very high. The air back cylinder pressure in a four-stroke SI engine, SAE flow pressure can be reduced the intake pressure outlet Paper 00-01-0371. from intake port to the engine cylinder. Average total Gamma T., 003. GT-POWER user manual, Gamma pressure is minimum pressure add maximum pressure Technologies, Inc. divided two. Average of total pressure in inlet process to Ganesan, V., 1999. Internal Combustion Engines. nd Edn. intake port and outlet process from intake port to engine Tata McGraw-Hill, New Delhi. cylinder is shown in Fig. 14 and 16. The figures shows Heywood, J.B., 1998. Internal Combustion Engine that the average pressure inlet to intake port the Fundamentals. McGraw-Hill, Singapore. highest is in 4000RPM engine speed and the lowest is in Ismail, A.R., Semin and A.B. Rosli, 007. Valve Flow 3000RPM engine speed, the average pressure outlet from Discharge Coefficient Investigation for Intake and intake port to engine cylinder the highest is in 4000 RPM Exhaust Port of Four Stroke Diesel Engines. J. Eng. engine speed and the lowest average pressure outlet from Applied Sci., : 1807-1811. 53

J. Eng. Applied Sci., 3 (1): 47-54, 008 Jawad, B., A. Dragoiu, L. Dyar, K. Zellner and C. Riedel, 003. Intake Design for Maximum Performance. SAE Paper 003-01-77. Klein, M., Eriksson and Nilsson, 00. Compression estimation from simulated and measured cylinder pressure. SAE Paper 00-01-0843. Kowalewicz, A., 1984. Combustion System of High-Speed Piston I.C. Engines, Wydawnictwa Komunikacji i Lacznosci, Warszawa. Piedrahita, A.R. Carlos, Riaza and F.Q. Héctro, 003. Prediction of in-cylinder pressure, temperature, and loads related to the crank-slider mechanism of I. C. engines: A computational model. SAE Paper 003-01-078. Rosli, A.B., Semin and A.R.Ismail, 006a. The Internal Combustion Engine Diversification Technology for The Future: A Review. Proceeding of International Seminar IMarEST-ITS, Surabaya, Indonesia. Rosli, A.B., Semin and A.R.Ismail, 006b. Investigation of Fuel Nozzle Performance on Direct Injection Diesel Engines Using Computational Simulation. MARINE J., Vol. 3. Rosli, A.B., Semin and A.R.Ismail, 007a. Proceeding of the Internal Combustion Engine Diversification Technology And Fuel Research for the Future: A Review, AEESEAP Regional Symposium, Kuala Lumpur, Malaysia, pp: 57-6. Rosli, A.B., Semin and A.R.Ismail, 007b. Effect of Engine Performance for Four-Stroke Diesel Engine Using Simulation. Proceeding of the 5th International Conference on Numerical Analysis in Engineering, Padang-West Sumatera, Indonesia. Rosli, A.B., Semin and A.R.Ismail, 007c. Development of Intake and Exhaust Stroke Flow Simulation in an Engine Cylinder Using CFD Model. Proceeding of NaCSEC Conference, Malaysia. Stone, R., 1997. Introduction to Internal Combustion Engines. nd Edn. SAE Inc, USA. Sanders, S.T., T. Kim and J.B. Ghandhi, 003. Gas temperature measurements during ignition in an HCCI engine. SAE Paper 003-01-0744. Semin, A.R. Ismail and A.B. Rosli, 007a. In An Engine Valve Lift Visualization And Simulation Performance Using CFD. Proceeding of Conference on Applications and Design in Mechanical Engineering (CADME), Malaysia. Semin, A.B. Rosli and A.R. Ismail, 007b. Air Flow Analysis of Four Stroke Direct Injection Diesel Engines Based on Air Pressure Input and L/D Ratio. Res. J. Applied Sci., : 1135-114. Semin, Bakar and A. Rosli, 007c. Nozzle Holes Effect on Unburned Fuel in Injected and In-Cylinder Fuel of Four Stroke Direct Injection Diesel Engine. Res. J. Applied Sci., : 1165-1169. Semin, A.B. Rosli and A.R. Ismail, 007d. Engine Power Calculation using Air Flow through Engine from Flowbench Test Flow of Four Stroke DI Diesel Engines. J. Eng. Applied Sci., : 181-1817. 54