mk Systems Profile Technology

PROFILE SYSTEMS mk Systems Profile Technology www.mkprofiles.com

How to use the Catalog Series Icons The following symbols identify the suitability of a particular component to its respective Profile Series. Any component not so identified is typically usable in all Profile Series. for Profile Series 25 for Profile Series for Profile Series, limited use in Series 50 for Profile Series 50, limited use in Series for Profile Series 50 for Profile Series 60 Cross-Reference between Sections The following symbol denotes that there is further relevant component information to be found on the referenced page. Further information on this chapter can be found in another section. See more Information page XXX Further information on this component can be found in another section. Pg. XXX Profile Descriptions and Ident- or Order-Numbers The numbering system is used to identify cut-tolength as well as stock length profiles. Description Profile mk 20.01 Order Number 54.01..* Profile number in the series Series description, Series Denotes Profile System 2000 Append the order number (four-digit) with the length in mm Profile number in the series Profile Series The Profile System 2000 The Profile System 2000 consists of 4 compatible Profile Series. Selection of the appropriate system is primarily dependant on the desired application as well as requirements such as load capacity, design or available space. Series 25 Typical applications of the mk Profile System 2000 Series 25 are for trade shows, electronics and small equipment. From light frames, displays, cabinets and shelving to prototypes, measurement and test equipment, control panels and electronic enclosures. Series As the most extensive system, Series is the basis for lighter machine frames, enclosures and guarding, workstations and our GTP system (Railings, Stairs and Platforms). Series 50 The structural profiles of Series 50 are designed for higher static loads in such areas as machine building, heavy machine frames and other load bearing structures. Series 60 The profiles of Series 60 were designed for applications which were historically the realm of steel construction. Using M12 connectors, the rigidity and load capacity of this series can be fully utilized. 14 mk Systems Profile Technology

Index General Information 16 mk Structural Profiles 18 mk Function Profiles 94 mk Assembly Components 1 mk Accessory Components 208 mk Assemblies 292 mk Examples of Customer Applications 304 mk Partners and Support 312 Component Index 318 Profile Index by Ident-Nr. 320 mk Systems Profile Technology 15

General Information Product Philosophy The product focus of mk is on supplying the highest quality profile technology, based on rigidity and functionality, to provide solutions for demanding production environments. The philosophy behind our assembly components is stability to prevent the overall structural integrity of the design from being limited because of its connections. mk offers 250 system profiles made of high-quality alloys, strength-oriented connecting components using 8 proven methods and a wide-ranging selection of accessories using readily available hardware. With four aluminum profile series identified by their base dimensions of 25,, 50, 60 the ideal system is available for any application. Profile Geometry The geometry of the mk Profile Technology System has been designed so that no gaps or exposed edges are visible when connecting profiles. As a result, areas where dirt can accumulate are minimized, as well as reducing the potential for cuts and injuries. The resulting assembly also looks markedly cleaner and more professional. Others mk Services Products mk offers everything from individual parts and components to assemblies all the way to complete design solutions using mk system components. Service Sales Our sales team can meet with you at your company or at ours. We also offer workshops and product training on a regular basis. Design Qualified engineers are available to support planning, layout and design throughout your entire project cycle. Transport Shipping mk guarantees world-wide shipments. Delivery times are minimized through the use of optimized processes in sales and production, as well as selected carriers. Packaging mk packages its products using environmentallyfriendly or recyclable materials ranging from small boxes to overseas containers. Special packaging is available at the customer's request. 16 mk Systems Profile Technology

Advantages of Profile Technology Shortened planning, design and assembly times Easily disassembled components can be reused Clean designs High strength-to-weight ratio using mk Profile Technology No Painting... because the system profiles have a smooth surface offer a good finish require no touchups No Grinding or Polishing... because beams can easily be added, removed or relocated no marks remain after assembly changes are made No Cutting or Welding... because all connections are bolted disassembled profiles and components can be reused Advantages of mk Profile Technology Most wide-ranging Profile System in the marketplace Machine building focused product philosophy (form follows function) Mature, stability-oriented connection methods Compatible technologies: Profile-, Conveyor-, Linear Technology and Factory Equipment from a single source Competent advice from mk sales engineers Customer aids including CAD library, electronic catalog and technical documentation System compatible components and hardware Use of high-quality materials mk supplies components, kits and assemblies Assembly mk Profile Technology systems are assembled without the need for extensive tools or services. Besides cutting the profiles, the most sophisticated tool required is a standard drill. Most connections, though, can be made without this. Naturally we can provide all these services for you. mk Systems Profile Technology 17

mk Structural Profiles Quick-Reference Structural Profiles 20 Standards, Norms and Calculations 24 System 2000 Series 25 27 System 2000 Series 37 System 2000 Series 50 55 System 2000 Series 60 63 Profile Supports Combi-Profiles 74 Foamed Profiles 76 Profile Ties 82 Profile Lattices 83 Profile Services Bent Profiles 84 Angle Braces 86 End Services 87 Threads and Inserts 91 Profile Ties 92 mk Systems Profile Technology 19

Quick-Reference Structural Profiles...* Profile length in mm Series 25 Series mk 2025.01 25.01....* Page 31 mk 2025.16 25.16....* Page 33 mk 20.01 54.01....* Page 41 mk 20.08 54.08....* Page 43 mk 2025.02 25.02....* Page 31 mk 2025.03 25.03....* Page 31 mk 2025.04 25.04....* Page 31 mk 2025.05 25.05....* Page 31 mk 2025.31 25.31....* Page 32 mk 2025.35 25.35....* Page 32 mk 2025.38 25.38....* Page 32 mk 2025.37 25.37....* Page 33 mk 2025.32 25.32....* Page 33 mk 2025.36 25.36....* Page 33 mk 2025.17 25.17....* Page 33 mk 2025.18 25.18....* Page 33 mk 2025.19 25.19....* Page 33 mk 2025.22 25.22....* Page 34 mk 2025.20 25.20....* Page 34 mk 2025.21 25.21....* Page 34 mk 2025.41 25.41....* Page 35 mk 2025.42 25.42....* Page 35 mk 2025.43 25.43....* Page 35 mk 20. 54.....* Page 41 mk 20.31 54.31....* Page 41 mk 20.02 54.02....* Page 41 mk 20.41 54.41....* Page 42 mk 20.52 54.52....* Page 42 mk 20.03 54.03....* Page 42 mk 20.45 54.45....* Page 42 mk 20.05 54.05....* Page 42 mk 20.06 54.06....* Page 42 mk 20.09 54.09....* Page 43 mk 20.10 54.10....* Page 43 mk 20.21 54.21....* Page 44 mk 20.11 54.11....* Page 44 mk 20.14 54.14....* Page 44 mk 20.15 54.15....* Page 44 mk 20.22 54.22....* Page 45 mk 20.12 54.12....* Page 45 mk 2025.39 25.39....* Page 33 mk 2025.25 25.25....* Page 33 mk 2025.44 25.44....* Page 35 mk 20.07 54.07....* Page 42 mk 20.24 54.24....* Page 45 mk 20.46 54.46....* Page 45 20 mk Systems Profile Technology

Series Series 50...* Profile length in mm mk 20.13 54.13....* Page 45 mk 20.39 54.39....* Page 49 mk 20.80 54.80....* Page 51 mk 2001 51.01....* Page 59 mk 20.04 54.04....* Page 45 mk 20.74 54.74....* Page 49 mk 20.86 54.86....* Page 51 mk 2000 51.00....* Page 59 mk 20.17 54.17....* Page 45 mk 20.18 54.18....* Page 45 mk 20.19 54.19....* Page 45 mk 20.75 54.75....* Page 49 mk 20.35 54.35....* Page 50 mk 20.34 54.34....* Page 50 mk 20.33 54.33....* Page 50 mk 20.43 54.43....* Page 52 mk 20.42 54.42....* Page 52 mk 20.44 54.44....* Page 52 mk 20.32 54.32....* Page 52 mk 20.67 54.67....* Page 53 mk 2002 51.02....* Page 59 mk 2004 51.04....* Page 59 mk 2005 51.05....* Page 60 mk 2011 51.11....* Page 60 mk 20.20 54.20....* Page 45 mk 20.93 54.93....* Page 46 mk 20.94 54.94....* Page 46 mk 20.30 54.30....* Page 50 mk 20.28 54.28....* Page 50 mk 20.85 54.85....* Page 53 mk 2025.41 25.41....* Page 54 mk 2007 51.07....* Page 60 mk 20.95 54.95....* Page 46 mk 20.16 54.16....* Page 46 mk 20.37 54.37....* Page 49 mk 20.38 54.38....* Page 49 mk 20.29 54.29....* Page 50 mk 2025.42 25.42....* Page 54 mk 2025.43 25.43....* Page 54 mk 2025.44 25.44....* Page 54 mk 2008 51.08....* Page 60 mk Systems Profile Technology 21

Quick-Reference Structural Profiles...* Profile length in mm Series 50 Series 60 Profile Supports mk 2072 51.72....* Page 60 mk 2003 51.03....* Page 60 mk 2016 51.16....* Page 61 mk 2060.01 60.01....* Page 67 mk 2060.02 60.02....* Page 67 mk 2060.03 60.03....* Page 67 mk 2060.30 60.30....* Page 69 mk 2060.31 60.31....* Page 69 mk 2060.26 60.26....* Page 71 Combi-Profile Page 74 Foamed Profile Page 76 mk 2031 51.31....* Page 62 mk 2060.27 60.27....* Page 71 mk 2033 51.33....* Page 62 mk 2060.04 60.04....* Page 68 mk 2060.28 60.28....* Page 71 Profile Tie Page 82 mk 2060.22 60.22....* Page 71 mk 2060.05 60.05....* Page 68 Profile Lattice Page 83 mk 2060.07 60.07....* Page 68 22 mk Systems Profile Technology

Standards, Norms and Calculations mk profiles are extruded aluminum and are available in standard lengths of 5100 mm. Profiles are available cut to length. Longer lengths may also be available on request. All structural profiles are chemically etched per E6, whereby surface grooves and roughnesses are removed. As a surface treatment the profiles are anodized with appx. 10µm of tint C0 (natural). This surface finish is alkaline and acid resistant (alkalines to PH 9.5 and acids to PH 4). The following tables show the allowable dimensional deviations from standard with maximum values indicated. Alloys of mk Profiles Per DIN 17615 Precision Profiles mk uses primarily two alloys for all profile series. For Series 25 and, for Series 50 and 60, AlMgSi 0.7 F28, which has a higher strength. 6063T6 6005T6 3.3206.72 3.3210.71 AlMgSi 0.7 F28 Density 2.7 kg/dm 3 2.7 kg/dm 3 E-Modulus 70.000 N/mm 2 70.000 N/mm 2 Rm 245 N/mm 2 270 N/mm 2 Rp0.2 195 N/mm 2 225 N/mm 2 Reduction of Area 10 % 8 % Hardness HB 75 90 Linear Expansion 23.4 10-6 1/K 23.4 10-6 1/K Thermal Conductivity 200-220 W/(m K) 180-220 W/(m K) Electrical Conductivity 38-34 m/(ω mm 2 ) 26-32 m/(ω mm 2 ) Squareness of cross-section all values in mm D W over Width W Range to Deviation from square of cross-section D - 0.20 60 0.30 60 90 0. 90 120 0.45 120 150 0.55 150 180 0.65 180 210 0.70 24 mk Systems Profile Technology

Straightness in extruded direction The deviation h1 for a given length may not exceed the chart values. In addition, any 300 mm long section may not exceed 0.3 mm from true. All values in mm. h1 L Length L to 1000 to 2000 to 3000 to 00 to 5000 to 6000 over 6000 Tolerance h 1 0.7 1.3 1.8 2.2 2.6 3.0 3.5 Twist all values in mm W L H Width W Allowable twist H per Length L over 1000 over 2000 over 3000 over 00 over 5000 over 6000 over to to 1000 to 2000 to 3000 to 00 to 5000 to 6000-25 1.0 1.5 1.5 2.0 2.0 2.0 25 50 1.0 1.2 1.5 1.8 2.0 2.0 50 75 1.0 1.2 1.2 1.5 2.0 2.0 75 100 1.0 1.2 1.5 2.0 2.2 2.5 per 100 125 1.0 1.5 1.8 2.2 2.5 3.0 quote 125 150 1.2 1.5 1.8 2.2 2.5 3.0 150 200 1.5 1.8 2.2 2.6 3.0 3.5 200 300 1.8 2.5 3.0 3.5 4.0 4.5 mk Systems Profile Technology 25

f f Relative deflection of base profiles Load at Center Maximum Stress: F L M M bmax = σ b = bmax R S = p0.2 4 W x,y σ b Maximum Deflection R p0.2 = 195 N/mm 2 () F L f = F L 3 48 E I x,y 225 N/mm 2 (AlMgSi 0.7 F28) Uniform Load Maximum Stress: q L M bmax = 2 M σ b = bmax R S = p0.2 R p0.2 = 8 W x,y σ b 195 N/mm 2 () Maximum Deflection 5 q L 225 N/mm f = 2 4 384 E I x,y (AlMgSi 0.7 F28) L q Deflection comparison of Base Profiles Series 25,, 50 and 60 L[mm] 6000 for F = 100 N at Center 5000 Series 60 00 Series 50 3000 Series 2000 Series 25 1000 F[mm] 0.1 1 10 26 mk Systems Profile Technology

System 2000 Series 25 Series 25 Dimensions and Threads Series 25 is designed on a 25 x 25 mm base dimension. The 6 mm T-slots are spaced at 25 mm. Threads can be cut into the extruded holes. Info regarding end services see page 87 Angle 15, 25.50.1000 SHCS DIN 6912, M5 x 8, 8.8 Zn, D691258 Ribbed Washer ø 5.3 Zn, K111010015 Nut M5, Steel Zn 25.50.0500 Profile ends can be tapped directly. M5 Recommended screw length = 2. dn M10 Different sizes possible with threaded inserts. Ensat M3 K112030002 M3 Ensat M6 K112030006 Helicoil M4 K112030104 Helicoil M8 K112030109 M8 M6 M4 d N = Thread diameter mk Systems Profile Technology 27

Determining the Deflection of the System Profiles The Deflection of the mk Structural Profiles can be ascertained mathematically as well as through the use of the ensuing logarithmic charts. Using the graphs is the fastest way of determining deflection. This method can also help recommend a profile given allowable deflection under a particular length/load situation. Using the given equation is recommended to determine exact deflection. The examples shown here are limited to profiles supported at both ends with a single load at the center an evenly distributed load As the weight of the beam itself can be considered an evenly distributed load, the deflection due to this can be taken from the graph Deflection due to evenly distributed load, or calculated as shown in the example equation. To determine the total deflection of overlapping profiles the deflection of the individual beams may be added (note to include the applied load as well as the weight of the beam). Consider the following application: A machine frame is constructed using Profile mk 2025.02, oriented vertically, as the top beams. This frame is 1525 mm long on one side. A surface plate is placed on these beams, which exerts a force of 237 N/m (distributed load) on this profile. A piece of equipment is placed onto the surface plate, which exerts an additional force of 750 N (point load) on the beam. This example is shown in the calculations at right. Caution! Die examples shown are only valid for in relation to beam lengths relatively small deflections! Example: Series 25 Deflection calculation using point load and weight of beam Load: f Point = 250 N q Distr. = 237 N/m L = 1585 mm Profile: mk 2025.02 (25 x 50 vertical) Using: I X = 12.19 cm 4 =^ 121900 mm 4 q Beam = 1.35 kg/m =^ 13.2 N/m E = 70000 N/m 2 (E-Modulus Alu) Deflection due to point load using the graph on page 29 f Point = 2.4 mm using the formula f f Point = Point L 3 = 250 N 1585 3 mm 3 48 E I X 48 70000 N/mm 2 121900 mm 4 f Point = 2.43 mm Deflection due to distributed weight of beam using the graph on page 30, with q = q Distr. + q Beam = 250 N/m = 2.4 mm f Distr. using the formula 5 q L 4 f Distr. = = 5 0.25 N/mm 1585 4 mm 4 384 E I x 384 70000 N/mm 2 121900 mm 4 f Distr. = 2.4 mm Total Deflection f Total = f Point + f Distr. = 2.4 mm + 2.4 mm f Total = 4.8 mm Caution! Ensure correct use of units. To be safe, compare calculations with the examples shown above. 28 mk Systems Profile Technology

Deflection of Load at Center Series 25 Example: Profile mk 2025.02 (high) I = 12.19 cm 4 F = 250N L = 1585 mm f = 2.4 mm 0.01 0.1 F[N] 1000 I[cm 4 ] 500 300 mk 2025.04 (high) 280.00 200 100 mk 2025.03 (high) 87.02 50 30 20 mk 2025.05 22.29 mk 2025.02 (high) 12.19 10 mk 2025.04 (flat) 9.58 mk 2025.03 (flat) 6.44 5 3 mk 2025.02 (flat) 3.30 2 mk 2025.01 1.73 1 L[mm] 100 200 300 500 1000 2000 3000 5000 10000 f F 1 10 100 f/mm L mk Systems Profile Technology 29

Deflection of Distributed Load Series 25 q Example: Profile mk 2025.02 (high) I = 12.19 cm 4 q = 250 N/m L = 1585 mm f = 2.4 mm 0.01 0.1 1 10 100 f/mm L 1000 I[cm 4 ] 500 300 mk 2025.04 (high) 280.00 36.8 200 100 mk 2025.03 (high) 87.02 25.0 50 30 20 mk 2025.05 22.29 21.6 mk 2025.02 (high) 12.19 13.2 10 mk 2025.04 (flat) 9.58 36.8 mk 2025.03 (flat) 6.44 25.0 5 3 mk 2025.02 (flat) 3.30 13.2 2 mk 2025.01 1.73 7.4 1 L[mm] 100 200 300 500 1000 2000 3000 5000 10000 f q[n/m] q of Profile [N/m] 30 mk Systems Profile Technology

...* Profile length in mm System 2000 Series 25 Series 25 25 25 25 100 Profile mk 2025.03 25.03....* 2.55 kg/m A 945.12 mm 2 Ix 87.02 cm 4 Iy 6.44 cm 4 Wx 17. cm 3 Wy 5.15 cm 3 25 25 ø 4.2 25 Profile mk 2025.01 25.01....* 0.75 kg/m A 279.13 mm 2 ø 8.5 Ix 1.73 cm 4 Iy 1.73 cm 4 Wx 1.38 cm 3 Wy 1.38 cm 3 25 25 25 25 25 150 Profile mk 2025.04 25.04....* 3.75 kg/m A 1389.11 mm 2 Ix 280.00 cm 4 Iy 9.58 cm 4 Wx 37.33 cm 3 Wy 7.66 cm 3 Profile mk 2025.02 25.02....* 1.35 kg/m 25 25 25 50 A 501.12 mm 2 Ix 12.19 cm 4 Iy 3.30 cm 4 Wx 4.87 cm 3 Wy 2.64 cm 3 25 50 25 50 Profile mk 2025.05 25.05....* 2.21 kg/m A 816.00 mm 2 Ix 22.30 cm 4 Iy 22.30 cm 4 Wx 8.90 cm 3 Wy 8.90 cm 3 mk Systems Profile Technology 31

...* Profile length in mm System 2000 Series 25 Series 25 with closed T-slots In addition to the standard system T-slot, the profiles of Series 25 with closed T-slots have a second, smaller slot which can accept paneling. This paneling can be recessed or reworked to be flush with the framing. Profile mk 2025.31 25.31....* 0.77 kg/m Alucobond 4 mm with serviced edges 25 25 A 283.99 mm 2 Ix 1.73 cm 4 Iy 1.62 cm 4 Wx 1.42 cm 3 Wy 1.29 cm 3 Profile mk 2025.35 25.35....* 0.75 kg/m 25 25 A 275.26 mm 2 Ix 1.71 cm 4 Iy 1.68 cm 4 Wx 1.38 cm 3 Wy 1.34 cm 3 ex. steel 2.5 mm thick Seal Strip, mk 3027, EPDM 10 25 10 25 Profile mk 2025.38 25.38....* 0.79 kg/m A 290.32 mm 2 Ix 1.52 cm 4 Iy 1.48 cm 4 Wx 1.27 cm 3 Wy 1.25 cm 3 ex. steel 2.5 mm thick 32 mk Systems Profile Technology

...* Profile length in mm 2.75 25 25 Profile mk 2025.37 25.37....* 0.73 kg/m A 267.02 mm 2 Ix 1.32 cm 4 Iy 1.28 cm 4 Wx 1.14 cm 3 Wy 1.12 cm 3 Profile mk 2025.25 25.25....* 1.30 kg/m A 482.45 mm 2 Ix 9.99 cm 4 Iy 9.99 cm 4 Wx 3.76 cm 3 Wy 3.76 cm 3 25 50 25 Profile mk 2025.32 25.32....* 1.29 kg/m A 474.55 mm 2 Ix 3.22 cm 4 Iy 12.03 cm 4 Wx 2.60 cm 3 Wy 4.81 cm 3 60 45 12.5 26 ø 8.5 Profile mk 2025.16 25.16....* 1.13 kg/m A 419.06 mm 2 25 50 25 Profile mk 2025.36 25.36....* 1.25 kg/m A 462.26 mm 2 Ix 3.12 cm 4 Iy 11.88 cm 4 Wx 2.58 cm 3 Wy 4.81 cm 3 30 25 120 135 Profile mk 2025.17 25.17....* 1.24 kg/m A 458.96 mm 2 Profile mk 2025.18 25.18....* 1.02 kg/m A 376.19 mm 2 R25 Profile mk 2025.39 25.39....* 1.1 kg/m 25 25 25 50 A 7.28 mm 2 Ix 2.05 cm 4 Iy 9.44 cm 4 Wx 1.81 cm 3 Wy 3.77 cm 3 150 Profile mk 2025.19 25.19....* 1.23 kg/m A 455.46 mm 2 25 25 mk Systems Profile Technology 33

...* Profile length in mm System 2000 Series 25 Series 25 25 25 100 Profile mk 2025.22 25.22....* 2.26 kg/m A 837.08 mm 2 Ix 64.26 cm 4 Iy 5.84 cm 4 Wx 12.95 cm 3 Wy 4.67 cm 3 25 57 50 Profile mk 2025.20 25.20....* 2.12 kg/m A 782.60 mm 2 Ix 15.51 cm 4 Iy 15.52 cm 4 Wx 6.20 cm 3 Wy 5.45 cm 3 70 Profile mk 2025.21 25.21....* 2.98 kg/m A 1100.95 mm 2 Ix 43.62 cm 4 Iy 43.62 cm 4 Wx 12.46 cm 3 Wy 12.46 cm 3 70 Tension Plug B51.03.009 34 mk Systems Profile Technology

...* Profile length in mm System 2000 Series 25 Profiles 25/ One side features T-slots for Series 25, the other for Series. This allows for a variety of combinations between Series 25, and even 50. The profiles are also ideal for situations requiring the installation of valves, sensors and switches. Profile mk 2025.43 25.43....* 2.86 kg/m M8 Ensat Insert (see page 91) K112030008 120 15 25 15 25 15 A 1057.66 mm 2 Ix 136.21 cm 4 Iy 4.44 cm 4 Wx 22.70 cm 3 Wy 4.37 cm 3 20 M8 M12 x1.5 80 15 15 25 15 20 20 Profile mk 2025.41 25.41....* 1.02 kg/m A 377.37 mm 2 Ix 6.20 cm 4 Iy 1.49 cm 4 Wx 3.10 cm 3 Wy 1.39 cm 3 Profile mk 2025.42 25.42....* 1.94 kg/m A 717.50 mm 2 Ix 42.51 cm 4 Iy 2.97 cm 4 Wx 10.63 cm 3 Wy 2.88 cm 3 160 15 25 15 25 15 25 15 20 Profile mk 2025.44 25.44....* 3.77 kg/m A 1397.82 mm 2 Ix 314.51 cm 4 Iy 5.90 cm 4 Wx 39.29 cm 3 Wy 5.86 cm 3 mk Systems Profile Technology 35

System 2000 Series Series Dimensions and Threads Series is designed on a x mm base dimension. The 10 mm T-slots are spaced at mm. Threads can be cut into the extruded holes. Info regarding end services see page 87-90 Angle E25, 82..0701 SHCS DIN 912, M8 x 16, 8.8 Zn, D0912816 Ribbed Washer ø 8.4 Zn, K111010017 Nut 1 M8, Steel Zn 34.01.0001 Profile ends can be tapped directly. M12 Recommended screw length = 2. dn Different sizes possible with threaded inserts. Ensat M8 K112030008 M10 M8 Helicoil M10 K112030110 d N = Thread diameter mk Systems Profile Technology 37

Determining the Deflection of the System Profiles The Deflection of the mk Structural Profiles can be ascertained mathematically as well as through the use of the ensuing logarithmic charts. Using the graphs is the fastest way of determining deflection. This method can also help recommend a profile given allowable deflection under a particular length/load situation. Using the given equation is recommended to determine exact deflection. The examples shown here are limited to profiles supported at both ends with a single load at the center an evenly distributed load As the weight of the beam itself can be considered an evenly distributed load, the deflection due to this can be taken from the graph Deflection due to evenly distributed load, or calculated as shown in the example equation. To determine the total deflection of overlapping profiles the deflection of the individual beams may be added (note to include the applied load as well as the weight of the beam). Consider the following application: A machine frame is constructed using Profile mk 20.02, oriented vertically, as the top beams. This frame is 2500 mm long on one side. A surface plate is placed on these beams, which exerts a force of 315 N/m (distributed load) on this profile. A piece of equipment is placed onto the surface plate, which exerts an additional force of 750 N (point load) on the beam. This example is shown in the calculations at right. Caution! Die examples shown are only valid for in relation to beam lengths relatively small deflections! Example: Series Deflection calculation using point load and weight of beam Load: f Point = 750 N q Distr. = 315 N/m L = 2500 mm Profile: mk 20.02 ( x 80 vertical) Using: I x = 83.26 cm 4 =^ 832600 mm 4 q Beam = 3.62 kg/m =^ 35.5 N/m Deflection due to point load using the graph on page 39 f Point = 4 mm using the formula f Point L 3 = 750 N 2500 3 mm f 3 Point = 48 E I x 48 70000 N/mm 2 832600 mm 4 f Point = 4.2 mm Deflection due to distributed weight of beam using the graph on page, with q Total = q Distr. + q Beam = 350 N/m = 3 mm f Distr. using the formula 5 q L f Distr. = 4 = 5 0.35 N/mm 2500 4 mm 4 384 E I x 384 70000 N/mm 2 832600 mm 4 f Distr. = 3.05 mm Total Deflection f Total = f Point + f Distr. = 4.2 mm + 3.05 mm f Total = 7.25 mm Caution! Ensure correct use of units. To be safe, compare calculations with the examples shown above. 38 mk Systems Profile Technology

Deflection of Load at Center Series 100 200 300 500 1000 2000 3000 5000 10000 0.01 0.1 1 10 100 f F L f/mm F[N] 10000 I[cm 4 ] 5000 3000 2000 mk 20.09 1528.25 1000 mk 20.08 (high) 948.91 500 300 200 mk 20.06 (high) 576.06 mk 20.07 (high) 4.69 mk 20.08 (flat) 272.05 mk 20.05 (high) 256.55 mk 20.07 (flat) 208.46 mk 20.03 149.64 100 mk 20.02 (high) 83.26 50 mk 20.06 (flat) 41.41 30 mk 20.05 (flat) 31.57 20 mk 20.02 (flat) 22.62 10 mk 20.01 12.13 L[mm] mk Systems Profile Technology 39

Deflection of Distributed Load Series q L 10000 I[cm 4 ] 5000 3000 2000 mk 20.09 1528.25 111.8 1000 mk 20.08 (high) 948.91 92.8 500 300 200 mk 20.06 (high) 576.06 61.4 mk 20.07 (high) 4.69 68.3 mk 20.08 (flat) 272.05 92.8 mk 20.05 (high) 256.55 46.0 mk 20.07 (flat) 208.46 68.3 mk 20.03 149.64 54.6 100 mk 20.02 (high) 83.26 35.5 50 mk 20.06 (flat) 41.41 61.4 30 mk 20.05 (flat) 31.57 46.0 20 mk 20.02 (flat) 22.62 35.5 10 mk 20.01 (flat) 12.13 19.6 L[mm] 100 200 300 500 1000 2000 3000 5000 10000 0.01 0.1 1 10 100 f f/mm q[n/m] q of Profile [N/m] mk Systems Profile Technology

...* Profile length in mm System 2000 Series Series Profile mk 20.01 54.01....* 2.00 kg/m A 742.16 mm 2 ø10 Ix 12.13 cm 4 Iy 12.13 cm 4 Wx 6.06 cm 3 Wy 6.06 cm 3 Profile mk 20. (light) 54.....* 1.64 kg/m standard profiles cut thread A 605.68 mm 2 Ix 10.52 cm 4 Iy 10.52 cm 4 Wx 5.26 cm 3 Wy 5.26 cm 3 light profiles cut thread Profile mk 20.31 (extra light) 54.31....* 1.50 kg/m A 551.55 mm 2 Ix 9.66 cm 4 Iy 9.66 cm 4 Wx 4.82 cm 3 Wy 4.82 cm 3 extra light profiles ø 7.4 M8 form thread 80 Profile mk 20.02 54.02....* 3.62 kg/m A 13.91 mm 2 Ix 83.26 cm 4 Iy 22.62 cm 4 Wx 20.84 cm 3 Wy 11.31 cm 3 mk Systems Profile Technology 41

System 2000 Series Series 80 Profile mk 20.41 (light) 54.41....* 2.85 kg/m A 1164.36 mm 2 Ix 68.89 cm 4 Iy 18.67 cm 4 Wx 17.22 cm 3 Wy 9.33 cm 3...* Profile length in mm Profile mk 20.05 54.05....* 4.69 kg/m A 1738.64 mm 2 Ix 256.55 cm 4 Iy 31.57 cm 4 Wx 43.75 cm 3 Wy 15.78 cm 3 Profile mk 20.52 (extra light) 54.52....* 2.59 kg/m A 958.00 mm 2 Ix 63.00 cm 4 Iy 17.30 cm 4 Wx 15.70 cm 3 Wy 8.68 cm 3 Profile mk 20.06 54.06....* 6.26 kg/m A 2318.93 mm 2 Ix 576.06 cm 4 Iy 41.41 cm 4 Wx 72.01 cm 3 Wy 20.70 cm 3 80 80 80 80 Profile mk 20.03 54.03....* 5.57 kg/m A 2062.18 mm 2 Ix 149.64 cm 4 Iy 149.64 cm 4 Wx 37.41 cm 3 Wy 37.41 cm 3 Profile mk 20.45 (light) 54.45....* 4.75 kg/m A 1760.65 mm 2 Ix 127.89 cm 4 Iy 127.89 cm 4 Wx 31.94 cm 3 Wy 31.94 cm 3 Profile mk 20.07 54.07....* 6.96 kg/m A 2579.26 mm 2 Ix 4.69 cm 4 Iy 208.46 cm 4 Wx 73.44 cm 3 Wy 52.11 cm 3 42 mk Systems Profile Technology

...* Profile length in mm 160 Profile mk 20.08 54.08....* 9.46 kg/m A 3504.88 mm 2 Ix 948.91 cm 4 Iy 272.05 cm 4 Wx 118.62 cm 3 Wy 68.01 cm 3 80 Profile mk 20.10 54.10....* 8.26 kg/m A 3058.61 mm 2 Ix 585.21 cm 4 Iy 585.21 cm 4 Wx 97.51 cm 3 Wy 97.51 cm 3 Profile mk 20.09 54.09....* 11. kg/m A 4223.70 mm 2 Ix 1528.25 cm 4 Iy 1528.25 cm 4 Wx 191.03 cm 3 Wy 191.03 cm 3 mk Systems Profile Technology 43

...* Profile length in mm System 2000 Series Series with closed T-slots In addition to the standard system T-slot, the profiles of Series with closed T-slots have a second, smaller slot which can accept paneling. This paneling can be recessed or reworked to be flush with the framing. Profile mk 20.21 54.21....* 1.84 kg/m A 684.82 mm 2 Ix 11.00 cm 4 Iy 10.21 cm 4 Wx 5.42 cm 3 Wy 5.10 cm 3 Profile mk 20.11 54.11....* 1.88 kg/m Alucobond 4 mm reworked, 50.15.3005 ex. alu. sheet, t = 2.5 mm A 695.79 mm 2 Ix 11.13 cm 4 Iy 11.13 cm 4 Wx 5.50 cm 3 Wy 5.50 cm 3 15 Profile mk 20.14 54.14....* 1.62 kg/m Seal Strip mk 3021, EPDM 15 ø 10 A 603.53 mm 2 Ix 8.30 cm 4 Iy 8.30 cm 4 Wx 4.75 cm 3 Wy 4.75 cm 3 ex. alu. sheet, t = 2 mm ø 10 Profile mk 20.15 54.15....* 1.51 kg/m A 561.03 mm 2 Ix 7.85 cm 4 Iy 7.85 cm 4 Wx 4.54 cm 3 Wy 4.54 cm 3 44 mk Systems Profile Technology

...* Profile length in mm 80 Profile mk 20.22 54.22....* 3.43 kg/m A 1271.68 mm 2 Ix 21.53 cm 4 Iy 75.54 cm 4 Wx 10.72 cm 3 Wy 18.89 cm 3 Profile mk 20.04 54.04....* 3.61 kg/m A1336.93 mm 2 Ix 71.82 cm 4 Iy 71.82 cm 4 Wx 18.80 cm 3 Wy18.80 cm 3 80 80 80 80 80 80 Profile mk 20.12 54.12....* 3.43 kg/m A 1273.46 mm 2 Ix 21.39 cm 4 Iy 77.91 cm 4 Wx 10.86 cm 3 Wy 19.86 cm 3 Profile mk 20.24 54.24....* 2.25 kg/m A 832.00 mm 2 Ix 16.60 cm 4 Iy 66.07 cm 4 Wx 8.30 cm 3 Wy 16.34 cm 3 Profile mk 20.46 54.46....* 5.44 kg/m A 2015.76 mm 2 Ix 145.08 cm 4 Iy 145.56 cm 4 Wx 35.63 cm 3 Wy 36.38 cm 3 Profile mk 20.13 54.13....* 5.32 kg/m A 1973.17 mm 2 Ix 141.92 cm 4 Iy 141.92 cm 4 Wx 36.05 cm 3 Wy 36.05 cm 3 60 ø10 70 ø10 120 135 150 Profile mk 20.17 54.17....* 2.64 kg/m A 977.89 mm 2 Profile mk 20.18 54.18....* 2.45 kg/m A 907.60 mm 2 Pg. 191 Profile mk 20.19 54.19....* 2.54 kg/m A 943.01 mm 2 Pg. 191 Profile mk 20.20 54.20....* 2.62 kg/m A 973.89 mm 2 Pg. 191 mk Systems Profile Technology 45

System 2000 Series Flat Finish Profiles Series...* Profile length in mm Profile mk 20.93 54.93....* 1.72 kg/m A 634.00 mm 2 Ix 11.00 cm 4 Iy 11.00 cm 4 Wx 5. cm 3 Wy 5. cm 3 Plug, K117010001 SHCS DIN 6912, M8 x 20, Stainless Steel D6912820A2 Spring Washer, ø 8.4, Stainless Steel D67698.4A2 Ensat M8, Stainless Steel K112030020 Profile mk 20.94 54.94....* 1.72 kg/m A 634.00 mm 2 Ix 11. cm 4 Iy 10.50 cm 4 Wx 5.73 cm 3 Wy 5.28 cm 3 End Cap, mk 2507 with rework End Cap Clamp, M6 K111030020 FH-SHCS DIN 7991, M6 x 12, Stainless Steel D7991612A2 Tension Plug, Stainless Steel B51.03.030 Profile mk 20.95 54.95....* 1.75 kg/m A 647.00 mm 2 Ix 11.00 cm 4 Iy 11. cm 4 Wx 5.41 cm 3 Wy 5.74 cm 3 Profile mk 20.16 54.16....* 1.25 kg/m A 444.60 mm 2 Ix 5.28 cm 4 Iy 6.22 cm 4 Wx 2.87 cm 3 Wy 3.11 cm 3 46 mk Systems Profile Technology

Drill System 2000 Series Flat Finish Profiles Series These profiles are identified by their smooth exterior surfaces. The absence of any gaps leaves contaminants no place to accumulate. The profiles are further designed to be completely standard system profiles, which is to say that they can be used with all assembly components. The T-slot can be opened, either partially or completely, with very little effort. In this instance, the T-slot cover can be removed with the parting tool. Designed exclusively for use with mk profiles, very little force is required. If a partial removal of the cover is desired, we recommend placing a drilled hole at the exact location using our drill fixture. Part Drill Fixture Flat Finish B51.03.020 Parting Tool B46.03.102 Deburr Deburring Block K902030001 mk Systems Profile Technology 47

System 2000 Series Telescoping Profiles Series In combination with base Profile x mm, height adjustment for workstations and frames is quickly and simply accomplished. Profiles can be serviced to your request (cut, drill, punch or mill). SHCS M8 x 16 D0912816, 8.8 Zn Plate left 50.09.0070 right 50.09.0071 Nut 1 PE M8 34.01.0018 SHCS M8 x 16 D0912816, 8.8 Zn FBH-Screw M8 x 16 D0912816, 8.8 Zn Guide mk 2575 Ribbed Washer ø 5.3 K111010015, Steel Zn SHCS M5 x 16 D0912516, 8.8 Zn Adjustable Handle, Plastic K110030204 SHCS M8 x 16 D0912816, 8.8 Zn Angle E25 82..0701 Nut 1 PE M8 34.01.0018 48 mk Systems Profile Technology

...* Profile length in mm Profile mk 20.37 54.37....* 1.17 kg/m A 426. mm 2 Ix 2.74 cm 4 Iy 14.65 cm 4 Wx 1.09 cm 3 Wy 9.73 cm 3 Profile mk 20.74 54.74....* 3.5 kg/m A 1296.23 mm 2 Ix 74.32 cm 4 Iy 56.44 cm 4 Wx 21.23 cm 3 Wy 18.66 cm 3 Profile mk 20.38 54.38....* 2.52 kg/m A 932.80 mm 2 Ix 43.13 cm 4 Iy 32.45 cm 4 Wx 13.60 cm 3 Wy 12.98 cm 3 Profile mk 20.75 54.75....* 3.01 kg/m A 1117.06 mm 2 Ix 68.36 cm 4 Iy 38.58 cm 4 Wx 27.35 cm 3 Wy 11.02 cm 3 Profile mk 20.39 54.39....* 3.00 kg/m A 1112.74 mm 2 Ix 49.87 cm 4 Iy 49.87 cm 4 Wx 16.31 cm 3 Wy 16.31 cm 3 mk Systems Profile Technology 49

System 2000 Series Profiles for Desks and Workstations...* Profile length in mm ø 10 100 120 Profile mk 20.30 54.30....* 4.36 kg/m A 1616.20 mm 2 Ix 242.23 cm 4 Iy 67.65 cm 4 Wx.20 cm 3 Wy 19.84 cm 3 50 65 ø 10 20 ø 7 22 25 60 ø10 Profile mk 20.35 54.35....* 1.61 kg/m A 592.96 mm 2 Ix 3.16 cm 4 Iy 19.20 cm 4 Wx 2.50 cm 3 Wy 6. cm 3 80 1 160 Profile mk 20.28 54.28....* 4.81 kg/m A 1782.26 mm 2 Ix 482.52 cm 4 Iy 84.85 cm 4 Wx 57.90 cm 3 Wy 24.34 cm 3 120 ø 10 80 120 Profile mk 20.34 54.34....* 3.56 kg/m A 1315. mm 2 Ix 139.67 cm 4 Iy 24.15 cm 4 Wx 23.53 cm 3 Wy 12.08 cm 3 Profile mk 20.33 54.33....* 3.16 kg/m A 1167.26 mm 2 Ix 162.27 cm 4 Iy 14.01 cm 4 Wx 27.33 cm 3 Wy 9.66 cm 3 50 66 50 ø 10 80 45 190 210 Profile mk 20.29 54.29....* 5.59 kg/m A 2071.13 mm 2 Ix 944.71 cm 4 Iy 102.04 cm 4 Wx 87.68 cm 3 Wy 30.09 cm 3 66 50 mk Systems Profile Technology

...* Profile length in mm System 2000 Series Profiles Series for Partitions Profiles mk 20.80 and 20.86 are often used in the manufacture of partitions and paneling. Gaps resulting from the use of the profile connectors provide an ideal conduit for electric or pneumatic services. For further information see pages 53 and 197 20 15 80 Profile mk 20.80 54.80....* 1.83 kg/m A 679.20 mm 2 Ix 36.26 cm 4 Iy 2. cm 4 Wx 9.06 cm 3 Wy 2.76 cm 3 20 120 Profile mk 20.86 54.86....* 2.90 kg/m A 1073.98 mm 2 Ix 121.74 cm 4 Iy 4.12 cm 4 Wx 20.28 cm 3 Wy 4.47 cm 3 15 Profile Connector 3, B51.03.023 Profile mk 20.80, 54.80....* mk Systems Profile Technology 51

...* Profile length in mm System 2000 Series Profiles Series as Covers Used to aesthetically enhance profile constructions for offices, trade shows or partitions. The covers are clipped into the profile T-slots without additional hardware. 11 Profile mk 20.43 54.43....* 0.41 kg/m 42.7 18 R 31.7 A 150.93 mm 2 82.7 51.1 R 60 3.5 26.3 Profile mk 20.42 54.42....* 0.68 kg/m A 251.60 mm 2 122.8 91 R 127 Profile mk 20.44 54.44....* 0.85 kg/m A 316.21 mm 2 3.5 26.3 Profile mk 20.32 54.32....* 1.26 kg/m A 464.85 mm 2 52 mk Systems Profile Technology

...* Profile length in mm System 2000 Series Profiles Series as Covers The profiles mk 20.67 and 20.85 are used as covers for structural profiles of Series. T-slots can be covered to prevent dirt from accumulating. The structure of the profiles prevents them sliding if they are used in tread applications. Also, using them as covers of wireways is quick and easy. The profiles do not require additional hardware to install. 3.5 25 80 3.7 9.7 Profile mk 20.67 54.67....* 0.78 kg/m A 292.03 mm 2 2 88 120 7.2 3.7 17 Profile mk 20.85 54.85....* 0.93 kg/m A 344. mm 2 3.5 mk Systems Profile Technology 53

...* Profile length in mm System 2000 Series Profiles 25/ One side features T-slots for Series 25, the other for Series. This allows for a variety of combinations between Series 25, and even 50. The profiles are also ideal in situations requiring the installation of valves, sensors and switches. Profile mk 2025.43 25.43....* 2.86 kg/m M8 Ensat Insert (see page 91) K112030008 M8 M12 x1.5 80 15 15 25 15 20 20 Profile mk 2025.41 25.41....* 1.02 kg/m A 377.37 mm 2 Ix 6.20 cm 4 Iy 1.49 cm 4 Wx 3.10 cm 3 Wy 1.39 cm 3 Profile mk 2025.42 25.42....* 1.94 kg/m A 717.50 mm 2 Ix 42.51 cm 4 Iy 2.97 cm 4 Wx 10.63 cm 3 Wy 2.88 cm 3 120 160 15 25 15 25 15 25 15 15 25 15 25 15 20 20 A 1057.66 mm 2 Ix 136.21 cm 4 Iy 4.44 cm 4 Wx 22.70 cm 3 Wy 4.37 cm 3 Profile mk 2025.44 25.44....* 3.77 kg/m A 1397.82 mm 2 Ix 314.51 cm 4 Iy 5.90 cm 4 Wx 39.29 cm 3 Wy 5.86 cm 3 54 mk Systems Profile Technology

System 2000 Series 50 Series 50 Dimensions and Threads Series 50 is designed on a 50 x 50 mm base dimension. The 10 mm T-slots are spaced at 50 mm. Threads can be cut into the extruded holes. Info regarding end services see page 87-90 Angle B25, 82.05.0003 SHCS DIN 912, M8 x 20, 8.8 ZN, D0912820 Ribbed washer ø 8.4 spring st. ZN, K111010017 Nut 1 M8, Steel ZN 34.01.0001 Profile ends can be tapped directly. M8 Recommended screw length = 2. dn Different sizes possible with threaded inserts. M5 Ensat M5 K112030005 M6 Helicoil M6 K112030106 d N = Thread diameter mk Systems Profile Technology 55

Determining the Deflection of the System Profiles The Deflection of the mk Structural Profiles can be ascertained mathematically as well as through the use of the ensuing logarithmic charts. Using the graphs is the fastest way of determining deflection. This method can also help recommend a profile given allowable deflection under a particular length/load situation. Using the given equation is recommended to determine exact deflection. The examples shown here are limited to profiles supported at both ends with a single load at the center an evenly distributed load As the weight of the beam itself can be considered an evenly distributed load, the deflection due to this can be taken from the graph Deflection due to evenly distributed load, or calculated as shown in the example equation. To determine the total deflection of overlapping profiles the deflection of the individual beams may be added (note to include the applied load as well as the weight of the beam). Consider the following application: A machine frame is constructed using Profile mk 2004, oriented vertically, as the top beams. This frame is 2500 mm long on one side. A surface plate is placed on these beams, which exerts a force of 315 N/m (distributed load) on this profile. A piece of equipment is placed onto the surface plate, which exerts an additional force of 750 N (point load) on the beam. This example is shown in the calculations at right. Caution! Die examples shown are only valid for in relation to beam lengths relatively small deflections! Example: Series 50 Deflection calculation using point load and weight of beam. Load: f Point = 750 N q Distr. = 315 N/m L = 2500 mm Profile: mk 2004 (50 x 100 vertical) Using: I x = 199 cm 4 =^ 1990000 mm 4 q Beam = 4.75 kg/m =^ 46.6 N/m Deflection due to point load using the graph on page 57 f Point = 1.7 mm using the formula f Point L 3 = 750 N 2500 3 mm 3 f Point = 48 E I x 48 70000 N/mm 2 1990000 mm 4 f Point = 1.75 mm Deflection due to distributed weight of beam using the graph on page 58 with q Total = q Distr. + q Beam = 362 N/m = 1.3 mm f Distr. using the formula 5 q L 4 = 5 0.362 N/mm 2500 4 mm f 4 Distr. = 384 E I x 384 70000 N/mm 2 1990000 mm 4 f Distr. = 1.32 mm Total Deflection f Total = f Point + f Distr. = 1.75 mm + 1.32 mm f Total = 3.07 mm ² 3.0 mm Caution! Ensure correct use of units. To be safe, compare calculations with the examples shown above. 56 mk Systems Profile Technology

Deflection of Load at Center Series 50 F[N] 10000 I[cm 4 ] 5000 3000 2000 mk 2008 (high) 1302.47 1000 500 300 200 mk 2011 383.36 mk 2005 334.81 mk 2004 (high) 199.96 100 mk 2008 (flat) 106.83 50 mk 2004 (flat) 55.38 30 mk 2000 29.90 20 10 L[mm] 100 200 300 500 1000 2000 3000 5000 10000 0.01 0.1 1 10 100 f F L f/mm mk Systems Profile Technology 57

Deflection of Distributed Load Series 50 q L 10000 I[cm 4 ] 5000 3000 2000 mk 2008 (high) 1302.47 89.3 1000 500 300 200 mk 2011 383.36 95.2 mk 2005 334.81 68.7 mk 2004 (high) 199.95 46.6 100 mk 2008 (flat) 106.83 89.3 50 mk 2004 (flat) 55.37 46.6 30 mk 2000 29.90 27.0 20 10 L[mm] 100 200 300 500 1000 2000 3000 5000 10000 0.01 0.1 1 10 100 f f/mm q[n/m] q of Profile [N/m] 58 mk Systems Profile Technology

...* Profile length in mm System 2000 Series 50 Series 50 Profile mk 2001 51.01....* 1.49 kg/m AlMgSi 0.7 F28 A 541.83 mm 2 Ix 14.26 cm 4 Iy 2.67 cm 4 Wx 5.70 cm 3 Wy 1.82 cm 3 The load capacity of beams can be significantly increased by inserting steel bar stock into several of the structural profiles. The attachment is accomplished through foaming, for example. Vertical posts can also benefit from this feature. 50 50 ø 7 Profile mk 2000 51.00....* 2.85 kg/m AlMgSi 0.7 F28 A 1084.16 mm 2 Ix 29.90 cm 4 Iy 29.90 cm 4 Wx 11.96 cm 3 Wy 11.96 cm 3 Bar stock 10 x x Length, K0010110.010 50 50 Profile mk 2002 51.02....* 1.75 kg/m A 693.05 mm 2 Ix 19.56 cm 4 Iy 19.56 cm 4 Wx 7.83 cm 3 Wy 7.83 cm 3 Profile mk 2004 51.04....* 4.87 kg/m AlMgSi 0.7 F28 50 100 A 1805.51 mm 2 Ix 199.96 cm 4 Iy 55.38 cm 4 Wx 39.99 cm 3 Wy 22.15 cm 3 50 Bar stock 10 x 70 x Length, K001011070.010 mk Systems Profile Technology 59

...* Profile length in mm Profile mk 2005 51.05....* 7.00 kg/m AlMgSi 0.7 F28 A 2655.52 mm 2 Ix 334.81 cm 4 Iy 334.81 cm 4 Wx 66.96 cm 3 Wy 66.96 cm 3 50 50 50 200 Profile mk 2008 51.08....* 9.09 kg/m AlMgSi 0.7 F28 A 3366.41 mm 2 Ix 1302.47 cm 4 Iy 106.83 cm 4 Wx 130.24 cm 3 Wy 42.73 cm 3 Profile mk 2011 51.11....* 9.70 kg/m 50 AlMgSi 0.7 F28 A 3671.30 mm 2 Ix 383.36 cm 4 Iy 383.36 cm 4 Wx 76.67 cm 3 Wy 76.67 cm 3 Profile mk 2072 51.72....* 4.62 kg/m AlMgSi 0.7 F28 A 1709.46 mm 2 Ix 151.77 cm 4 Iy 151.77 cm 4 Wx 28.75 cm 3 Wy 28.75 cm 3 Profile mk 2007 51.07....* 6.42 kg/m AlMgSi 0.7 F28 A 2381.00 mm 2 Ix 622.49 cm 4 Iy 48.67 cm 4 Wx 83.00 cm 3 Wy 27.38 cm 3 50 50 Profile mk 2003 51.03....* 2.00 kg/m A 761.72 mm 2 Ix 14.01 cm 4 Iy 14.01 cm 4 Wx 6.49 cm 3 Wy 6.49 cm 3 60 mk Systems Profile Technology

System 2000 Series 50 Series 50 Profile with closed T-slots...* Profile length in mm Profile mk 2016 has been designed to be a completely standard system profile, which is to say that it can be used with all assembly components. The T-slot can be opened, either partially or completely, with very little effort. In this instance, the T-slot cover can be removed with the parting tool. Designed exclusively for use with mk profiles, very little force is required. If a partial removal of the cover is desired, we recommend placing a drilled hole at the exact location. Closed Profile Parting Tool B46.03.102 50 50 Profile mk 2016 51.16....* 3.13 kg/m A 1158.84 mm 2 Ix 32.47 cm 4 Iy 32.47 cm 4 Wx 12.99 cm 3 Wy 12.99 cm 3 Deburring Block K902030001 mk Systems Profile Technology 61

...* Profile length in mm System 2000 Series 50 Series 50 Telescoping Profiles In combination with the base Profile mk 2000 (50 x 50 mm), height adjustment for workstations, conveyors and subframes is easily accomplished. These profiles are available with services to your specifications (cut, drilled, milled). Nut 1 M8, Steel ZN, 34.01.0001 Flanged Button-Head M8x16, 10.9 ZN, K112010003 SHCS DIN 912, M8 x 16, 8.8 ZN, D0912816 Hex Head Screw DIN 933, M8 x 16, 8.8 ZN D0933816 20.5 30 50.5 60 28 Profile mk 2033 51.33....* 1.50 kg/m AlMgSi 0.7 F28 A 553.89 mm 2 Ix 5.22 cm 4 Iy 27.72 cm 4 Wx 4.94 cm 3 Wy 9.24 cm 3 51 Profile mk 2031 51.31....* 2.85 kg/m 60 51 75 AlMgSi 0.7 F28 A 1120.06 mm 2 Ix 79.17 cm 4 Iy 55.59 cm 4 Wx 23.18 cm 3 Wy 18.53 cm 3 Adjustable Handle, Cast Zinc, K110030055 Nut 1 M8, Steel ZN, 34.01.0001 62 mk Systems Profile Technology

System 2000 Series 60 Series 60 Dimensions and Threads Series 60 is designed on a 60 x 60 mm base dimension. The 14 mm T-slots are spaced at 60 mm. Threads can be cut into the extruded holes. Info regarding end services see page 87-90 Profile ends can be tapped directly. M12 Recommended screw length = 2. dn Reduced load capacity with M16 thread M16 Different sizes possible with threaded inserts. Ensat M8 K112030008 M8 Ensat M12 K112030010 Helicoil M10 K112030110 M10 M12 d N = Thread diameter mk Systems Profile Technology 63

Determining the Deflection of the System Profiles The Deflection of the mk Structural Profiles can be ascertained mathematically as well as through the use of the ensuing logarithmic charts. Using the graphs is the fastest way of determining deflection. This method can also help recommend a profile given allowable deflection under a particular length/load situation. Using the given equation is recommended to determine exact deflection. The examples shown here are limited to profiles supported at both ends with a single load at the center an evenly distributed load As the weight of the beam itself can be considered an evenly distributed load, the deflection due to this can be taken from the graph Deflection due to evenly distributed load, or calculated as shown in the example equation. To determine the total deflection of overlapping profiles the deflection of the individual beams may be added (note to include the applied load as well as the weight of the beam). Consider the following application: A machine frame is constructed using Profile mk 2060.02, oriented vertically, as the top beams. This frame is 2500 mm long on one side. A surface plate is placed on these beams, which exerts a force of 630 N/m (distributed load) on this profile. A piece of equipment is placed onto the surface plate, which exerts an additional force of 1500 N (point load) on the beam. This example is shown in the calculations at right. Caution! Die examples shown are only valid for in relation to beam lengths relatively small deflections! Example: Series 60 Deflection calculation using point load and weight of beam Load: f Point = 1500 N q Distr. = 630 N/m L = 2500 mm Profile: mk 2060.02 (60 x 120 vertical) Using: I x = 4 cm 4 =^ 000 mm 4 q Beam = 6.95 kg/m =^ 68.2 N/m Deflection due to point load using the graph on page 65 f Point = 1.7 mm using the formula f Point L 3 = 1500 N 2500 3 mm f 3 Point = 48 E I x 48 70000 N/mm 2 000 mm 4 f Point = 1.73 mm Deflection due to distributed weight of beam using the graph on page 66, with q Total = q Distr. + q Beam = 698 700 N/mm = 1.3 mm f Distr. using the formula f Distr. = 5 q L 4 = 5 0.698 N/mm 2500 4 mm 4 384 E I x 384 70000 N/mm 2 000 mm 4 = 1.25 mm f Distr. Total Deflection f Total = f Point + f Distr. = 1.73 mm + 1.25 mm f Total = 2.98 mm ² 3.0 mm Caution! Ensure correct use of units. To be safe, compare calculations with the examples shown above. 64 mk Systems Profile Technology

Deflection of Load at Center Series 60 F[N] 10000 I[cm 4 ] 0.01 0.1 1 10 100 f/mm 5000 3000 2000 1000 500 mk 2060.07 (high) 86.0 mk 2060.04 (high) 2657.1 mk 2060.03 (high) 1210.5 mk 2060.07 (flat) 1177.3 mk 2038.85 (flat) 757.0 mk 2038.85 (high) 732.5 mk 2060.05 659.86 mk 2060.02 (high) 4.43 300 200 100 mk 2060.04 (flat) 189.92 mk 2060.03 (flat) 146.66 mk 2060.02 (flat) 103.48 50 mk 2060.01 60.17 30 20 10 100 200 300 500 1000 2000 3000 5000 10000 L[mm] mk Systems Profile Technology 65

Deflection of Distributed Load Series 60 I[cm 4 ] q of Profile [N/m] mk 2060.07 (high) 86.0 177.5 mk 2060.04 (high) 2657.1 119.6 mk 2060.03 (high) 1210.5 93.9 mk 2060.07 (flat) 1177.3 177.5 mk 2038.85 (flat) 757.0 116.2 mk 2038.85 (high) 732.5 116.2 mk 2060.05 659.86 100.7 mk 2060.02 (high) 4.43 68.2 mk 2060.04 (flat) 189.92 119.6 mk 2060.03 (flat) 146.66 93.9 mk 2060.02 (flat) 103.48 68.2 mk 2060.01 60.17 42.3 L[mm] 100 200 300 500 1000 2000 3000 5000 10000 0.01 0.1 1 10 100 f/mm 10000 q[n/m] 5000 3000 2000 1000 500 300 200 100 50 30 20 10 66 mk Systems Profile Technology

...* Profile length in mm System 2000 Series 60 Series 60 Profile mk 2060.01 60.01....* 4.31 kg/m AlMgSi 0.7 F28 A 1596.60 mm 2 Ix 60.17 cm 4 Iy 60.17 cm 4 Wx 20.05 cm 3 Wy 20.05 cm 3 The load capacity of beams can be significantly increased by inserting steel bar stock into several of the structural profiles. The attachment is accomplished through foaming, for example. Vertical posts can also benefit from this feature. Profile mk 2060.02 60.02....* 6.95 kg/m AlMgSi 0.7 F28 A 2574.25 mm 2 Ix 4.43 cm 4 Iy 103.48 cm 4 Wx 67.34 cm 3 Wy 34.49 cm 3 Bar stock 10 x 110 x Length, K001011110.010 Profile mk 2060.03 60.03....* 9.57 kg/m AlMgSi 0.7 F28 A 3544.44 mm 2 Ix 1210.53 cm 4 Iy 146.66 cm 4 Wx 134.50 cm 3 Wy 48.89 cm 3 mk Systems Profile Technology 67

...* Profile length in mm System 2000 Series 60 Series 60 Profile mk 2060.04 60.04...* 12.19 kg/m AlMgSi 0.7 F28 A 4515.94 mm 2 Ix 2657.18 cm 4 Iy 189.92 cm 4 Wx 221.18 cm 3 Wy 63.28 cm 3 Profile mk 2060.07 60.07....* 18.09 kg/m A 6700.21 mm 2 Ix 86.05 cm 4 Iy 1177.39 cm 4 Wx 3.50 cm 3 Wy 169.23 cm 3 Profile mk 2060.05 60.05....* 10.26 kg/m AlMgSi 0.7 F28 A 3800.71 mm 2 Ix 659.86 cm 4 Iy 659.86 cm 4 Wx 109.85 cm 3 Wy 109.85 cm 3 68 mk Systems Profile Technology

...* Profile length in mm System 2000 Series 60 Series 60 Cover and Adapter Profiles The cover profile mk 2060.30 closes open T-slots for applications in the food industry, for example. With profile mk 2060.31, 10 mm thick paneling can be fixed in the profile T-slots. In addition, this profile serves as an adapter profile for series and 50 keyed angles. mk 2060.02 60.02....* Cover profile mk 2060.30 60.30....* Adapter profile mk 2060.31 60.31....* Profile mk 2060.30 60.30....* 0.14 kg/m Profile mk 2060.31 60.31....* 0.21 kg/m SHCS DIN 912 M8x20, 8.8 ZN, D0912820 Nut 1 M8, Steel ZN 34.01.0001 Adapter profile mk 2060.31 60.31....* mk Systems Profile Technology 69

...* Profile length in mm System 2000 Series 60 Series 60 Corner and Cover Profiles Even heavy industrial frames may require a certain aesthetic element. We offer several corner covers for this application. Screw connections or possible wiring/tubing can also be hidden. In addition, Profile mk 2060.26 can accept a variety of decorative sheets to not only accent the frame, yet identify potential wire and tubing locations. Profile mk 2060.26 Decorative sheet Spring Washer SHCS DIN 6912 M12x25, 8.8 ZN, D69121225 Nut 1 M12, Steel ZN 34.60.0301 70 mk Systems Profile Technology

...* Profile length in mm Profile mk 2060.26 60.26....* 1.20 kg/m A 447.28 mm 2 Profile mk 2060.22 60.22....* 6.05 kg/m AlMgSi 0.7 F28 A 2239.62 mm 2 Ix 301.86 cm 4 Iy 301.86 cm 4 Wx 45.36 cm 3 Wy 45.36 cm 3 Profile mk 2060.27 60.27....* 1.22 kg/m A 454.74 mm 2 Profile mk 2060.28 60.28....* 2.14 kg/m A 797. mm 2 mk Systems Profile Technology 71

Profile Supports Combi-Profile Foamed Profile Profile Lattice Profile Tie mk Systems Profile Technology 73

Profile Supports Combi-Profile With combination profiles mk 20.91 and mk 2068 the structural profiles of series and 50 can be combined to manufacture very compact structural framing elements. The resulting cavities can be used to contain parts or wiring, which can also be attached to the available interior T-slots. Decorative paneling can be slid into the small exterior slots, to identify the contents for example. Linear Technology also benefits from using combiprofiles as a way of increasing load capacity over long lengths. Ribbed Washer ø 8.4, Spring steel Zn, K111010017 SHCS M8 x 16, DIN 912, 8.8 Zn, D0912816 Nut 1 M8, Steel Zn, 34.01.0001 Nut 1 M5, Steel Zn, 34.12.0001 FH-SHCS M5 x 25, DIN 7991, 8.8 Zn, D7991525 74 mk Systems Profile Technology

...* Profile length in mm Profile mk 20.91 54.91....* 2.2 kg/m A 814.00 mm 2 Ix 112.74 cm 4 Iy 0.59 cm 4 Wx 18.79 cm 3 Wy 0.93 cm 3 Profile mk 2068 51.68....* 4.47 kg/m AlMgSi 0.7 F28 A 1655.88 mm 2 Ix 546.14 cm 4 Iy 2.29 cm 4 Wx 60.70 cm 3 Wy 2.72 cm 3 100 80 150 180 17 Profile mk 2069 51.69....* 1.93 kg/m AlMgSi 0.7 F28 A 717.43 mm 2 100 150 180 Ix 270.50 cm 4 Iy 0.79 cm 4 Wx 30.05 cm 3 Wy 1.34 cm 3 17 mk Systems Profile Technology 75

76 mk Systems Profile Technology Profile Supports Foamed Profile A technological advantage unto itself, profile supports using this foam process create beams with enormous stability. They are heavily used as columns or supporting beams for mezzanines and machine frames. Foamed profiles are normally available in lengths of up to 5000 mm. On request, special lengths may be possible. Basically, this process is available to all profiles of series, 50 and 60. They are manufactured to customer specifications. Once foamed, the profiles can no longer be disassembled, and can also be used where dynamic loads are present.

Examples Series Series 50 Series 60 mk 20.06/mk 20.90/mk 20.06 lx 3499.45 cm 4 Wx 349.94 cm 3 ly 1388.15 cm 4 Wy 173.48 cm 3 m 18.92 kg/m S 70.08 cm 2 mk 2005/mk 2067/mk 2004 lx 3973.88 cm 4 Wx 305.74 cm 3 mk 2060.03/mk 2060./mk 2060.03 lx 6516.68 cm 4 Wx 543.09 cm 3 ly 726.45 cm 4 Wy 145.24 cm 3 ly 3763.64 cm 4 Wy 418.05 cm 3 m 16.94 kg/m S 62.74 cm 2 m 27.49 kg/m S 101.81 cm 2 mk 20.05/mk 20.72/mk 20.05 lx 2736.05 cm 4 Wx 273.50 cm 3 ly 1134.74 cm 4 Wy 189.06 cm 3 m 15.78 kg/m S 58.46 cm 2 mk 2011/mk 2067/mk 2011 lx 8267.15 cm 4 Wx 551.05 cm 3 mk 2060.05/mk 2060./mk 2060.05 lx 12749.08 cm 4 Wx 707.95 cm 3 ly 959.42 cm 4 Wy 191.85 cm 3 ly 1724.88 cm 4 Wy 287.44 cm 3 m 24.71 kg/m S 91.53 cm 2 m 28.88 kg/m S 106.95 cm 2 mk 20.06/mk 20.72/mk 20.06 lx 3497.29 cm 4 Wx 349.59 cm 3 mk 2008/mk 2067/mk 2008 lx 4226.93 cm 4 Wx 422.66 cm 3 mk 2060.03/mk 2060.43/mk 2060.03 lx 6516.58 cm 4 Wx 542.93 cm 3 ly 1836.15 cm 4 Wy 211.67 cm 3 ly 3310.74 cm 4 Wy 313.96 cm 3 ly 3233.64 cm 4 Wy 320.42 cm 3 m 18.91 kg/m S 70.05 cm 2 m 23.24 kg/m S 86.06 cm 2 m 27.61 kg/m S 102.27 cm 2 mk Systems Profile Technology 77

Profile Supports Foamed Profile Series...* Profile length in mm Profile mk 20.72 54.72....* 3.09 kg/m 120 80 134 A 1145.10 mm 2 Ix 210.20 cm 4 Iy 3.99 cm 4 Wx 31.37 cm 3 Wy 3.99 cm 3 Profile mk 20.72, 54.72....* Profile mk 20.90 54.90....* 3.64 kg/m A 1345.10 mm 2 Ix 437.73 cm 4 Iy 4.71 cm 4 Wx 50.31 cm 3 Wy 4.31 cm 3 160 120 18.8 174 18.8 78 mk Systems Profile Technology

Profile Supports Foamed Profile Series 50...* Profile length in mm Profile mk 2067 51.67....* 2.48 kg/m AlMgSi 0.7 F28 A 935.60 mm 2 Ix 111.67 cm 4 Iy 2.25 cm 4 Wx 18.61 cm 3 Wy 2.79 cm 3 Profile mk 2067, 51.67....* mk Systems Profile Technology 79

Profile Supports Foamed Profile Series 60 Profile mk 2060.43, 60.43....* Profile mk 2060., 60.....* Profile mk 2060.44, 60.44....* Profile mk 2060.41, 60.41....* 80 mk Systems Profile Technology

...* Profile length in mm Profile mk 2060. 60.....* 4.10 kg/m A 1519.65 mm 2 Ix 226.19 cm 4 Iy 8.27 cm 4 Wx 31. cm 3 Wy 6.63 cm 3 Profile mk 2060.43 60.43....* 4.31 kg/m A 1598.48 mm 2 Ix 2.56 cm 4 Iy 13.61 cm 4 Wx 33. cm 3 Wy 9.29 cm 3 Profile mk 2060.41 60.41....* 6.05 kg/m A 2241.90 mm 2 Ix 13.04 cm 4 Iy 685.57 cm 4 Wx 10.59 cm 3 Wy 67.20 cm 3 Profile mk 2060.44 60.44....* 6.26 kg/m A 2319.60 mm 2 Ix 18.70 cm 4 Iy 726.73 cm 4 Wx 12.35 cm 3 Wy 71.25 cm 3 mk Systems Profile Technology 81

...* Profile length in mm Profile Supports Profile Tie If the values and heights indicated below are acceptable, profile ties are a cost-effective alternative to lattices. Profile Ties see page 92 Profile mk 2000 Profile Tie 1 B34.02.003 20 170 Profile mk 2056 51.56....* 4.09 kg/m A 1518.13 mm 2 Ix 450.68 cm 4 Iy 2.43 cm 4 Wx 53.02 cm 3 Wy 2.16 cm 3 Connecting Height H Series / 152 mm Series /50 151 mm Series 50/50 150 mm Profile Tie 3 B34.02.005 Profile mk 20.01 220 Profile mk 2057 51.57....* 4.77 kg/m A 1768.13 mm 2 Ix 926.35 cm 4 Iy 2.48 cm 4 Wx 84.17 cm 3 Wy 2.20 cm 3 Connecting Height H Series / 202 mm Series /50 201 mm Series 50/50 200 mm 20 H 82 mk Systems Profile Technology

Profile Supports Profile Lattice mk profile lattices can be manufactured using a variety of profile combinations. Inform us of your particular application, and we will provide you with a suitable lattice including the specific calculations. Further information on request. Profile Wedges see page 195 Example: Lattice H L Upper and lower runner mk 20.03 Brace profile mk 20.01 Box Lattice Ix 31.185.00 cm 4 Iy 643.00 cm 4 Wx 705.00 cm 3 Wy 87.00 cm 3 Brace length = 2 (H-31.7) with -series brace = 2 (H-22.3) with 25-series brace mk Systems Profile Technology 83

Profile Services Bent Profiles Our ability to bend profiles is especially helpful in manufacturing special conveyors, turntables, etc. Curves in a variety of angles and radii can be made to specification. For all applications requiring curves, bends and rings, for example, we are limited only by the indicated minimum radius (vertical orientation). Profile Dimensions min. Radius mk 2025.01 25 x 25 mm 250 mm mk 2025.02 25 x 50 mm 250 mm mk 2025.03 25 x 100 mm 250 mm mk 2025.04 25 x 150 mm 250 mm Rmin mk 2025.22 25 x 100 mm 275 mm mk 2025.41 20 x mm 250 mm mk 2025.42 20 x 80 mm 250 mm mk 2025.43 20 x 120 mm 250 mm 84 mk Systems Profile Technology

Profile Dimensions min. Radius Profile Dimensions min. Radius mk 2025.44 20 x 160 mm 250 mm mk 2239 12 x 20 mm 150 mm mk 20.01 x mm 600 mm mk 20.02 x 80 mm 600 mm mk 20.80 20 x 80 mm 250 mm mk 20.86 20 x 120 mm 250 mm mk 2001 25 x 50 mm 0 mm mk 2000 50 x 50 mm 1200 mm mk 2004 50 x 100 mm 1200 mm mk 2066 25 x 100 mm 550 mm mk 20.56 x 120 mm 1300 mm mk 2238 15 x 30 mm 150 mm mk Systems Profile Technology 85

...* Profile length in mm Profile Services Angle Braces mk Braces offer the ability to easily add stiffness to a heavily loaded profile frame. Using slot nuts makes later installation effortless. Stock lengths 200, 300, 0 and 500 mm. L Brace 01 (mk 20.01) 51CC...* L Brace (mk 20.) 54CC...* Nut 1 M8, Steel Zn, 34.01.0001 Ribbed Washer ø 8.4, Spring Steel Zn, K111010017 SHCS M8 x 20, DIN 912, 8.8 Zn, D0912820 mk 20.02, 52CA...* mk 20.02 Brace 02 (mk 20.02) 52CA...* L 86 mk Systems Profile Technology

...* Profile length in mm Profile Services End Services End Services include cutting, milling, drilling and tapping. Our production capabilities allow us to provide these services in a timely and cost-effective manner. The following descriptions and part numbers are just a portion of available services. Customer services to drawings are also available. For angled cuts, please indicate the following: Please indicate the requested drilling locations for Tension Plugs. A A B B C α α β L L C D mk Profile Services Series 25 mk 2025.01 one end angle cut α 2501AE.* both ends angle cut α and β 2501AF.* Profile faced 2501AI.* one end thread M10 2501AA.* both ends thread M10 2501AB.* one end drill ø 5.8 for Tension Plug 2501BA.* both ends drill ø 5.8 for Tension Plug 2501BB.* one end threaded insert Ensat M6 B25.01.001.* both ends threaded insert Ensat M6 B25.01.002.* one end threaded insert Helicoil M8 B25.01.010.* both ends threaded insert Helicoil M8 B25.01.011.* mk 2025.02 one end angle cut α 2502AE.* both ends angle cut α and β 2502AF.* one end angle cut α (long side) 2502AG.* both ends angle cut α and β (long side) 2502AH.* Profile faced 2502AI.* one end 2 x thread M10 2502AC.* mk Systems Profile Technology 87

...* Profile length in mm mk Profile Services Series 25 mk 2025.02 both ends 2 x thread M10 2502AD.* one end 2 x drill ø 5.8 for Tension Plug 2502BA.* both ends 2 x drill ø 5.8 for Tension Plug 2502BB.* one end 2 x threaded insert Ensat M6 B25.02.001.* both ends 2 x threaded insert Ensat M6 B25.02.002.* one end 2 x threaded insert Helicoil M8 B25.02.010.* both ends 2 x threaded insert Helicoil M8 B25.02.011.* mk Profile Services Series 20.01 20. mk 20.01 one end angle cut α 51AE.* 54AD.* both ends angle cut α and β 51AF.* 54AC.* Profile faced 51AI.* 54AI.* one end thread M12 51AA.* 54AA.* mk 20. both ends thread M12 51AB.* 54AB.* one end drill ø 10 for Tension Plug 51BA.* 54BA.* both ends drill ø 10 for Tension Plug 51BB.* 54BB.* one end drill ø 9 for Economy Fastener 51BE.* 54BE.* both ends drill ø 9 for Economy Fastener 51BF.* 54BF.* one end threaded insert Ensat M8 B54.01.003.* B54..002.* both ends threaded insert Ensat M8 B54.01.002.* B54..001.* one end threaded insert Helicoil M10 B54.01.001.* B54..004.* both ends threaded insert Helicoil M10 B54.01.007.* B54..005.* 20.02 20.41 mk 20.02 one end angle cut α 52 AG.* 5441AG.* both ends angle cut α and β 52 AH.* 5441AH.* one end angle cut α (long side) 52AE.* 5441AA.* both ends angle cut α and β (long side) 52AF.* 5441AF.* mk 20.41 Profile faced 52AI.* 5441AI.* one end 2 x thread M12 52AA.* 5441AC.* both ends 2 x thread M12 52AB.* 5441AB.* one end 2 x drill ø 10 for Tension Plug 52BA.* 5441BA.* both ends 2 x drill ø 10 for Tension Plug 52BB.* 5441BB.* one end 2 x drill ø 9 for Economy Fastener 52BE.* 5441BE.* both ends 2 x drill ø 9 for Economy Fastener 52BF.* 5441BF.* one end 2 x threaded insert Ensat M8 B54.02.002.* B54.41.002.* both ends 2 x threaded insert Ensat M8 B54.02.001.* B54.41.001.* one end 2 x threaded insert Helicoil M10 B54.02.004.* B54.41.004.* both ends 2 x threaded insert Helicoil M10 B54.02.005.* B54.41.005.* 88 mk Systems Profile Technology

mk Profile Services Series 20.03 20.45 mk 20.03 one end angle cut α 53AE.* 5445AE.* both ends angle cut α and β 53AF.* 5445AF.* Profile faced 53AI.* 5445AI.* one end 4 x thread M12 53AA.* 5445AA.* both ends 4 x thread M12 53AB.* 5445AB.* mk 20.45 one end 2 x drill ø 10 for Tension Plug 53BA.* 5445BA.* both ends 2 x drill ø 10 for Tension Plug 53BB.* 5445BB.* one end 2 x drill ø 9 for Economy Fastener 53BE.* 5445BE.* both ends 2 x drill ø 9 for Economy Fastener 53BF.* 5445BF.* one end 4 x threaded insert Ensat M8 B54.03.002.* B54.45.002.* both ends 4 x threaded insert Ensat M8 B54.03.001.* B54.45.001.* one end 4 x threaded insert Helicoil M10 B54.03.004.* B54.45.004.* both ends 4 x threaded insert Helicoil M10 B54.03.005.* B54.45.005.* mk Profile Services Series 50 mk 2000 one end angle cut α 5100AE.* both ends angle cut α and β 5100AF.* Profile faced 5100AI.* one end 2 x thread M8 diagonal 5100AA.* both ends 2 x thread M8 diagonal 5100AB.* one end 4 x thread M8 5100AC.* both ends 4 x thread M8 5100AD.* one end drill ø 10 for Tension Plug 5100BF.* both ends drill ø 10 for Tension Plug 5100BG.* mk 2004 one end angle cut α 5104BG.* both ends angle cut α and β 5104BH.* one end angle cut α (long side) 5104AE.* both ends angle cut α and β (long side) 5104AF.* Profile faced 5104AI.* one end 2 x thread M8 diagonal 5104AB.* both ends 2 x thread M8 diagonal 5104AG.* one end 4 x thread M8 5104AA.* both ends 4 x thread M8 5104AC.* mk 2005 one end angle cut α 5105AE.* both ends angle cut α and β 5105AC.* Profile faced 5105AI.* one end 2 x thread M8 diagonal 5104AF.* both ends 2 x thread M8 diagonal 5105AG.* one end 4 x thread M8 5105AB.* both ends 4 x thread M8 5105AA.*...* Profile length in mm mk Systems Profile Technology 89

...* Profile length in mm mk Profile Services Series 60 mk 2060.01 one end 4 x thread M12 6001AA.* both ends 4 x thread M12 6001AB.* one end 1 x thread Ensat M12 B60.01.605 both ends 1 x thread Ensat M12 B60.01.606 one end angle cut α 6001AE.* both ends angle cut α and β 6001AF.* mk 2060.02 one end 4 x thread M12 6002AA.* both ends 4 x thread M12 6002AB.* one end 2 x thread Ensat M12 B60.02.605 both ends 2 x thread Ensat M12 B60.02.606 one end angle cut α 6002AG.* both ends angle cut α and β 6002AH.* one end angle cut α (long side) 6002AE.* both ends angle cut α and β (long side) 6002AF.* mk 2060.05 one end 4 x thread Ensat M12 B60.05.605 both ends 4 x thread Ensat M12 B60.05.606 one end angle cut α 6005AE.* both ends angle cut α and β 6005AF.* one end 4 x thread M12 6005AA.* both ends 4 x thread M12 6005AB.* 90 mk Systems Profile Technology

Profile Services Threads and Inserts For servicing the holes at the profile ends. The installation tools are for manual operation. Service for ø Hole Tools Req. Order-Nr. Order-Nr. Series thread Tools Threaded length Insert thread M5 25 4.2 mm Tap M5 15 mm K903060005 thread M8 50 7.0 mm Tap M8 25 mm K903060008 thread M10 25 8.5 mm Tap M10 30 mm K903060010 thread M12 10.0 mm Tap M12 35 mm K903060012 thread M12 60 10.5 mm Tap M12 35 mm K903060012 thread M16 60 14.5 mm Tap M16 45 mm K903060016 Ensat M3 25 4.2 mm Tap M5x0.5 mm, 10 mm K903060105 K112030002 Installation Tool K902010004 Ensat M5 50 7.0 mm Tap M8x1 mm, 15 mm K903060108 K112030005 Installation Tool K902010008 Ensat M6 25 8.5 mm Tap M9x1 mm, 15 mm K903060109 K112030006 Installation Tool K902010010 Ensat M8 10.0 mm Tap M12x1.5 mm, 20 mm K903060113 K112030008 Installation Tool K902010012 Ensat M8 60 10.5 mm Tap M12x1.5 mm, 20 mm K903060113 K112030008 Installation Tool K902010012 Ensat M12 60 14.5 mm Tap M16x1.5 mm, 25 mm K903060116 K112030010 Installation Tool K902010016 Helicoil M4 25 4.2 mm Helicoil Tap M4 mm, 10 mm K903060204 K112030104 Installation Tool K902010204 Helicoil M6 50 7.0 mm Helicoil Tap M6 mm, 15 mm K903060206 K112030106 Installation Tool K902010206 Helicoil M8 25 8.5 mm Helicoil Tap M8 mm, 15 mm K903060208 K112030109 Installation Tool K902010208 Helicoil M10 10.0 mm Helicoil Tap M10 mm, 20 mm K903060210 K112030110 Installation Tool K902010210 Helicoil M10 60 10.5 mm Helicoil Tap M10 mm, 20 mm K903060210 K112030110 Installation Tool K902010210 mk Systems Profile Technology 91

Profile Services Profile Ties More Information see page 83 Profile Tie 5156BA0100 Profile mk 20.56 Profile Tie 5156BB0200 Hex Nut M8, D09348 Clamp, 30.00.0055 SHCS DIN 912, M8 x 30, 8.8 Zn, D0912830 Ribbed Washer ø 8.4 St Zn, K111010017 Profile mk 20.57 Profile Tie 5156BC00 Profile Tie 5156CA0100 92 mk Systems Profile Technology

Profile Tie 5156CB0080 Profile Tie 5157CA0100 Profile Tie 5157BA0100 Profile Tie 5157CB0080 Profile Tie 5157BB0200 Profile Tie 5157BC00 Tie Clamp 1 B34.02.003 complete Tie Clamp 3 B34.02.005 mk Systems Profile Technology 93

mk Function Profiles Quick-Reference Function Profiles 96 Linear Technology 101 Conveyor Technology 109 Triggers and Sliders 118 Planning and Information Boards 119 Drawing Holders 120 19'' Rack 121 Cover and Connection Profiles 122 Partitions 124 Swing Door Stops 125 Guarding 126 Steps, Flooring and Facades 127 Windows 128 Wireways 130 Profiles for Rework 131 mk Systems Profile Technology 95

Quick-Reference Function Profiles...* Profile length in mm Linear Technology mk 2038.20 38.20....* Page 102 mk 2038.30 38.30....* Page 102 mk 2038.31 38.31....* Page 103 mk 2038.41 38.41....* Page 103 mk 2038.42 38.42....* Page 103 mk 2038.21 38.21....* Page 103 mk 2038.32 38.32....* Page 103 mk 2038.33 38.33....* Page 103 mk 2038.44 38.44....* Page 103 mk 2038.46 38.46....* Page 103 mk 2038.36 38.36....* Page 103 mk 2038.37 38.37....* Page 103 mk 2038.01 38.01....* Page 104 mk 2038.05 38.05....* Page 104 mk 2038.06 38.06....* Page 104 mk 2038.07 38.07....* Page 104 mk 2038.11 38.11....* Page 104 mk 2038.12 38.12....* Page 104 mk 2038.13 38.13....* Page 104 mk 2038.75 38.75....* Page 105 mk 2038.77 38.77....* Page 105 mk 2038.85 38.85....* Page 105 mk 2038.51 38.51....* Page 106 mk 2038.55 38.55....* Page 106 mk 2038.56 38.56....* Page 106 mk 2038.58 38.58....* Page 107 mk 2038.60 38.60....* Page 107 mk 2038.65 38.65....* Page 107 mk 2038.61 38.61....* Page 107 mk 2039.25 39.25....* Page 107 mk 2039.26 39.26....* Page 107 mk 2015 51.15....* Page 107 Conveyor Technology mk 2010 51.10....* Page 110 mk 2012 51.12....* Page 110 mk 2060 51.60....* Page 111 mk 2061 51.61....* Page 111 mk 2086 51.86....* Page 112 mk 2065 51.65....* Page 112 mk 2066 51.66....* Page 112 mk 20.56 54.56....* Page 113 mk 2038.50 38.50....* Page 106 96 mk Systems Profile Technology

...* Profile length in mm Conveyor Technology mk 20.57 54.57....* Page 113 mk 2237 52.37....* Page 116 Triggers and Sliders mk 22 52.....* Page 118 19" Rack mk 2025.23 25.23....* Page 121 mk 20.58 54.58....* Page 113 mk 2007 51.07....* Page 116 mk 2241 52.41....* Page 118 mk 2025.24 25.24....* Page 121 mk 2075 51.75....* Page 114 mk 2100 51.76....* Page 114 mk 2251 52.51....* Page 116 mk 20.76 54.76....* Page 117 Planning and Information Boards mk 2150 51.77....* Page 114 mk 2253 52.53....* Page 117 mk 20.71 54.71....* Page 119 mk 2080 51.80....* Page 115 mk 2238 52.38....* Page 115 mk 2239 52.39....* Page 115 mk 2234 52.34....* Page 116 mk 2254 52.54....* Page 117 mk 20.77 54.77....* Page 119 mk 2025.45 25.45....* Page 120 mk 2025.46 25.46....* Page 120 mk 2235 52.35....* Page 116 mk 2236 52.36....* Page 116 mk Systems Profile Technology 97

Quick-Reference Function Profiles...* Profile length in mm Cover and Connection Profiles mk 2205 52.05....* Page 122 mk 2206 52.06....* Page 122 mk 2207 52.07....* Page 122 for Partitions mk 20.83 54.83....* Page 124 mk 20.84 54.84....* Page 124 mk 20.47 54.47....* Page 124 Guarding mk 2218 52.18....* Page 126 mk 2217 52.17....* Page 126 mk 20.60 54.60....* Page 126 for Steps, Flooring and Facades mk 20.68 54.68....* Page 127 mk 20.69 54.69....* Page 127 mk 2208 52.08....* Page 122 mk 2209 52.09....* Page 123 mk 2210 52.10....* Page 123 mk 2211 52.11....* Page 123 mk 20.48 54.48....* Page 124 for Swing Doors mk 20.88 54.88....* Page 125 mk 20.26 54.26....* Page 127 mk 2212 52.12....* Page 123 mk 20.25 54.25....* Page 125 mk 2213 52.13....* Page 123 mk 2214 52.14....* Page 123 mk 2215 52.15....* Page 123 mk 2216 52.16....* Page 123 mk 2203 52.03....* Page 123 mk 2204 52.04....* Page 123 98 mk Systems Profile Technology

...* Profile length in mm Windows Rework mk 20.81 54.81....* Page 128 mk 2025.47 25.47....* Page 131 mk 2085 51.85....* Page 132 mk 20.63 54.63....* Page 134 Wireways mk 20.82 54.82....* Page 128 mk 20.59 54.59....* Page 128 mk 20.97 54.97....* Page 128 mk 20.50 54.50....* Page 130 mk 20.51 54.51....* Page 130 mk 2050 51.50....* Page 130 mk 2051 51.51....* Page 130 mk 2048 51.48....* Page 130 mk 20.49 54.49....* Page 130 mk 2025.82 25.82....* Page 131 mk 20.98 54.98....* Page 131 mk 20.99 54.99....* Page 131 mk 20.61 54.61....* Page 131 mk 2043 51.43....* Page 131 mk 2029 51.29....* Page 131 mk 2090 51.90....* Page 131 mk 2060.82 60.82....* Page 132 mk 20.55 54.55....* Page 132 mk 2088 51.88....* Page 132 mk 2097 51.97....* Page 132 mk 2089 51.89....* Page 132 mk 2081 51.81....* Page 132 mk 2060.71 60.71....* Page 133 mk 2060.72 60.72....* Page 133 mk 2060.73 60.73....* Page 133 mk 2052 51.52....* Page 133 mk 2053 51.53....* Page 133 mk 2054 51.54....* Page 133 mk 20.62 54.62....* Page 134 mk 20.66 54.66....* Page 134 mk 20.65 54.65....* Page 134 mk 20.27 54.27....* Page 134 mk 2084 51.84....* Page 134 mk 2250 52.50....* Page 135 mk 2271 52.71....* Page 135 mk 20.87 54.87....* Page 135 mk 20.36 54.36....* Page 135 mk 2095 51.95....* Page 135 mk 2098 51.98....* Page 132 mk 2070 51.70....* Page 134 mk Systems Profile Technology 99

Quick-Reference Function Profiles...* Profile length in mm Rework Further mk 2074 51.74....* Page 135 mk 20.78 54.78....* Page 135 mk 20.79 54.79....* Page 135 mk 20.89 54.89....* Page 136 mk 2096 51.96....* Page 136 mk 2244 52.44....* Page 136 mk 2245 52.45....* Page 136 mk 2046 51.46....* Page 136 mk 2047 51.47....* Page 136 mk 2231 52.31....* Page 136 mk 2232 52.32....* Page 136 mk 2246 52.46....* Page 137 mk 2248 52.48....* Page 137 mk 2270 52.70....* Page 137 mk 2294 52.94....* Page 137 mk 2295 52.95....* Page 137 mk 2296 52.96....* Page 137 mk 2038 51.38....* Page 137 mk 2093 51.93....* Page 137 mk 2079 51.79....* Page 138 mk 2062 51.62....* Page 138 mk 20.64 54.64....* Page 138 mk 2030 51.30....* Page 138 mk 20.70 54.70....* Page 138 mk 2049 51.49....* Page 139 mk 2219 52.19....* Page 139 mk 2063 51.63....* Page 139 mk 2064 51.64....* Page 139 mk 20.54 54.54....* Page 139 mk 2060.81 60.81....* Page 139 mk 2073 51.73....* Page 139 mk 2083 51.83....* Page 139 mk 2087 51.87....* Page 139 100 mk Systems Profile Technology

Function Profiles Linear Technology Linear Technology The mk Linear Technology System consists of glide, recirculating ball and dual-row grooved roller bearings. Just a few basic elements are required for the construction of precision tracks and carriages. Detailed information regarding the selection and design of linear systems is available on request. The profiles shown on the following pages are designed primarily for use with the grooved roller bearings. Hardened steel rods are securely clamped over their entire length using precision clamping profiles which ensure exact parallel. The load ratings of the systems are dependant on the rod diameter selected. mk offers four guide rod diameters for the four profile series. Guide Roller 6, K101100003 Guide Roller 10, K101100001 Guide Roller 16, K101100002 Guide Roller 20, K101100006 mk Systems Profile Technology 101

...* Profile length in mm Function Profiles Linear Technology Linear Technology System Layout The guide track is mounted directly to the base supporting profile, whereby attention must be paid to using compatible profile series and systems. Available adapter profiles provide options for additional combinations. The selection of a linear system is based of the desired support profile and rollers. When selecting a support profile, calculate both the deflection and the strength of the profile. For proper operation of our linear modules, total deflection cannot exceed 1 mm/m. Standard mechanical calculations as shown in the respective profile sections of this catalog are sufficient. Further information is available on request. Series 25 Load specifications per roller ø 6 mm Series ø 6 mm ø 6 mm ø 10 mm ø 10 mm ø 16 mm Value Roller for Roller for Roller for Roller for rod rod rod rod ø 6 mm ø 10 mm ø 16 mm ø 20 mm so* 4 4 4 4 F radial 175N 1000N 2000N 3250N F axial 60N 300N 500N 825N static load Cow 890N 5100N 9500N 16600N dynamic load Cw 1270N 8500N 16800N 29500N ø 6 mm ø 10 mm * static load safety factor with regard to plastic deformation of the roller at the rod contact point Series 50 mk 2038.20 38.20....* 0.44 kg/m AlMgSi 0.7 F28 Used with ø 10 mm ø 16 mm ø 20 mm Guide Rod ø 6 mm Series 60 mk 2038.30 38.30....* 0.79 kg/m AlMgSi 0.7 F28 ø 10 mm ø 16 mm ø 20 mm Used with Guide Rod ø 6 mm 102 mk Systems Profile Technology

...* Profile length in mm mk 2038.31 38.31....* 1.07 kg/m AlMgSi 0.7 F28 Used with Guide Rod ø 10 mm mk 2038.41 38.41....* 1.36 kg/m AlMgSi 0.7 F28 Used with Guide Rod ø 10 mm mk 2038.42 38.42....* 1.37 kg/m AlMgSi 0.7 F28 Used with Guide Rod ø 10 mm mk 2038.44 38.44....* 3.09 kg/m AlMgSi 0.7 F28 Used with Guide Rod ø 16 mm mk 2038.46 38.46....* 3.97 kg/m AlMgSi 0.7 F28 Used with Guide Rod ø 20 mm mk 2038.21 38.21....* 0.88 kg/m AlMgSi 0.7 F28 Used with Guide Rod ø 6 mm mk 2038.32 38.32....* 2.09 kg/m AlMgSi 0.7 F28 Used with Guide Rod ø 10 mm mk 2038.36 38.36....* 3.62 kg/m AlMgSi 0.7 F28 A 13.88 mm 2 Used with Guide Rod ø 16 mm mk 2038.33 38.33....* 2.96 kg/m AlMgSi 0.7 F28 Used with Guide Rod ø 16 mm mk 2038.37 38.37....* 4.60 kg/m AlMgSi 0.7 F28 A 1701.91 mm 2 Used with Guide Rod ø 20 mm mk Systems Profile Technology 103

...* Profile length in mm Function Profiles Linear Technology Linear Technology Clamping One-Sided For linear applications which are subject to a large moment of inertia, an additional guide roller and track can be mounted between the carriage and the support profile. mk 2038.07 38.07....* 1.50 kg/m AlMgSi 0.7 F28 Used with Guide Rod ø 16 mm mk 2038.01 38.01....* 0.42 kg/m AlMgSi 0.7 F28 Used with Guide Rod ø 6 mm mk 2038.11 38.11....* 1.27 kg/m AlMgSi 0.7 F28 Used with Guide Rod ø 10 mm mk 2038.05 38.05....* 0.75 kg/m AlMgSi 0.7 F28 Used with Guide Rod ø 6 mm mk 2038.12 38.12....* 1.77 kg/m AlMgSi 0.7 F28 Used with Guide Rod ø 16 mm mk 2038.06 38.06....* 1.12 kg/m AlMgSi 0.7 F28 Used with Guide Rod ø 10 mm mk 2038.13 38.13....* 2.07 kg/m AlMgSi 0.7 F28 Used with Guide Rod ø 20 mm 104 mk Systems Profile Technology

...* Profile length in mm Function Profiles Linear Technology Linear Technology Interior Guides mk 2038.75 38.75....* 3.41 kg/m AlMgSi 0.7 F28 Used with Guide Rod ø 6 mm, Guided inside Profile mk 2038.77 Carriage Plate Centric Guide Roller, B60.02.015 mk 2038.77 38.77....* 4.34 kg/m AlMgSi 0.7 F28 Used with Guide Rod ø 10 mm, Guided inside mk 2038.85 38.85....* 11.85 kg/m AlMgSi 0.7 F28 A 4390.63 mm 2 Ix 732.52 cm 4 Iy 757.05 cm 4 Wx 108.74 cm 3 Wy 126.17 cm 3 Used with Guide Rod ø 10 mm, Guided inside mk Systems Profile Technology 105

...* Profile length in mm Function Profiles Linear Technology Linear Technology Adapter Profiles Adapter profiles are used in instances where a larger supporting profile is desired (or required) and the standard carriage interferes with such an arrangement. In addition, adapter profiles can be used to combine linear components with different profile series. mk 2038.50 38.50....* 0.46 kg/m AlMgSi 0.7 F28 Support Profile ex. mk 20.05, 54.05....* Carriage LF101, B90.00.006 mk 2038.51 38.51....* 0.89 kg/m AlMgSi 0.7 F28 mk 2038.55 38.55....* 0.77 kg/m AlMgSi 0.7 F28 mk 2038.56 38.56....* 1.67 kg/m AlMgSi 0.7 F28 106 mk Systems Profile Technology

...* Profile length in mm Function Profiles Linear Technology Linear Technology Adapter Profiles Function Profiles Linear Technology Linear Technology Profiles for Glides mk 2038.58 38.58....* 3.46 kg/m AlMgSi 0.7 F28 mk 2039.25 39.25....* 1.83 kg/m AlMgSi 0.7 F28 mk 2038.60 38.60....* 1.04 kg/m AlMgSi 0.7 F28 mk 2039.26 39.26....* 2.75 kg/m AlMgSi 0.7 F28 mk 2038.65 38.65....* 1.00 kg/m AlMgSi 0.7 F28 mk 2015 51.15....* 2.75 kg/m AlMgSi 0.7 F28 mk 2038.61 38.61....* 1.90 kg/m AlMgSi 0.7 F28 mk Systems Profile Technology 107

...* Shaft lenght in mm Function Profiles Linear Technology Guide Rod Stock lengths for Cf 53 and X46 Cr13 is 00 mm, for Cf 53 (galvanized) is 3000 mm. Guide Rod 6 0.22 kg/m Guide Rod 10 0.62 kg/m Guide Rod 16 1.58 kg/m Guide Rod 20 2.47 kg/m Guide Rods Cf 53 Cf 53 X46 Cr13 1.1213 1.1213 1.34 (galvanized) ø 6 mm 7003AK...* 7003DC...* 7003EC...* ø 10 mm 7003AA...* 7003DH...* 7003EH...* ø 16 mm 7003AM...* 7003DP...* 7003EP...* ø 20 mm 7003CM...* 7003DT...* 7003ET...* 108 mk Systems Profile Technology

Function Profiles Conveyor Technology Modul-con with Profile mk 2060 Timing Belt conveyor with Profile mk 2010 Multiflex conveyor with Profile mk 2061 Accum. Roller Chain conveyor with Profile mk 2012 Roller conveyor with mk 2065 Wire Mesh Belt conveyor with Profile mk 20.76 mk Systems Profile Technology 109

Function Profiles Conveyor Technology Profiles for Dual Lane Conveyors...* Profile length in mm 20 25 25 38.5 50 100 Profile mk 2010 51.10....* 4.87 kg/m AlMgSi 0.7 F28 A 1797.62 mm 2 Ix 192.74 cm 4 Iy 51.41 cm 4 Wx 38.28 cm 3 Wy 19.86 cm 3 60 85 135 Profile mk 2012 51.12....* 7.56 kg/m AlMgSi 0.7 F28 A 2799.19 mm 2 Ix 516.93 cm 4 Iy 119.32 cm 4 Wx 73.96 cm 3 Wy 39.77 cm 3 for for Duplex Chain conveyor 1/2" Timing Belt conveyor for Belt Conveyor Option A Option B Wear Strip mk 1033 Wear Strip mk 1041 Wear Strip mk 1017 Wear Strip mk 1034 Wear Strip mk 1042 Wear Strip mk 1039 Wear Strip mk 1051 Accumulating Roller Chain Wear Strip mk 1050 Wear Strip mk 1048 Accumulating Roller Chain Wear Strip mk 1047 Wear Strip K102 29/.7 Wear Strip mk 1022 110 mk Systems Profile Technology

...* Profile length in mm Function Profiles Conveyor Technology Profiles for Chain Conveyors Manufactured using a minimum of components, our Modul-con and Multiflex conveyors are ideal for industrial applications. The systems are tough and require a minimum of service once in operation. Typically used for parts transport between machines and operators, profiles mk 2060 and mk 2061 are the basis for extremely flexible modular conveyor systems. 25 25 80 Profile mk 2060 51.60....* 3.24 kg/m AlMgSi 0.7 F28 A 1244.73 mm 2 Ix 88.07 cm 4 Iy 25.80 cm 4 Wx 22.01 cm 3 Wy 12.53 cm 3 65 100 150 Profile mk 2061 51.61....* 6.17 kg/m A 2287.09 mm 2 Ix 595.29 cm 4 Iy 57.63 cm 4 Wx 79.37 cm 3 Wy 26.32 cm 3 25 45 50 Wear Strip mk 1060, 22.60.2000 Single Strand Chain 1 /2" x 5 /16" Wear Strip mk 1022, 22.22.2000 Multiflex chain mk Systems Profile Technology 111

...* Profile length in mm Function Profiles Conveyor Technology Profiles for Roller Conveyors Profile mk 2086 51.86....* 1.64 kg/m AlMgSi 0.7 F28 A 615.92 mm 2 Profile mk 2065 51.65....* 1.68 kg/m AlMgSi 0.7 F28 A 627.11 mm 2 75 Ix 39.73 cm 4 Iy 4.23 cm 4 Wx 11.73 cm 3 Wy 4.63 cm 3 25 SHCS DIN 912, M8 x 20, 8.8 Zn, D0912820 Gravity Roller type 3, Plastic 25 75 100 Profile mk 2066 51.66....* 2.36 kg/m AlMgSi 0.7 F28 A 877.41 mm 2 Ix 98.72 cm 4 Iy 6.15 cm 4 Wx 19.74 cm 3 Wy 6. cm 3 112 mk Systems Profile Technology

...* Profile length in mm Function Profiles Conveyor Technology Profiles for Roller Conveyors Profile mk 20.56 54.56....* 2.72 kg/m A 1006.76 mm 2 Ix 204.27 cm 4 Iy 17.96 cm 4 Wx 34.01 cm 3 Wy 6.69 cm 3 Pg. 53 Sprocket driven roller 1/2", z = 14 Profile mk 20.57 54.57....* 4.15 kg/m A 1536.89 mm 2 Ix 353.58 cm 4 Iy 111.58 cm 4 Wx 58.93 cm 3 Wy 22.50 cm 3 Drive Chain 1 /2" (Roller Chain) Wear Strip mk 10.94, 21.94... Wear Strip mk 10.93, 21.93... Profile mk 20.58 54.58....* 2.72 kg/m A 1005.78 mm 2 Ix 41.44 cm 4 Iy 17.71 cm 4 Wx 10.37 cm 3 Wy 8.86 cm 3 mk Systems Profile Technology 113

...* Profile length in mm Function Profiles Conveyor Technology Frames for Belt Conveyors The profile is designed so that the belt return is protected on the frame's underside. The conveyor can thus be placed directly onto equipment. Profile mk 2075 51.75....* 2.24 kg/m AlMgSi 0.7 F28 A 830.23 mm 2 Ix 6.81 cm 4 Iy 49.58 cm 4 Wx 5.34 cm 3 Wy 13.22 cm 3 Stainless steel slider bed t = 1 mm Profile mk 2100 51.76....* 2.65 kg/m AlMgSi 0.7 F28 A 980.23 mm 2 Ix 8.00 cm 4 Iy 103.23 cm 4 Wx 6.49 cm 3 Wy 20.64 cm 3 Profile mk 2150 51.77....* 3.70 kg/m AlMgSi 0.7 F28 A 1364.65 mm 2 Ix 10.48 cm 4 Iy 306.81 cm 4 Wx 8.97 cm 3 Wy.90 cm 3 114 mk Systems Profile Technology

...* Profile length in mm Function Profiles Conveyor Technology Side Rails 50 Pg. 285 Profile mk 2080 51.80....* Used to clamp Ø 10 mm rods 25 Wear Strip mk 1043, 22.43....* Wear Strip mk 1031, 22.31....* Profile mk 2239, 52.39....* Profile mk 2238, 22.38....* Pg. 270 Profile mk 2238 52.38....* 0.4 kg/m A 148.19 mm 2 Profile mk 2235, 52.35....* (H = 25) Profile mk 2236, 52.36....* (H = 50) Profile mk 2237, 52.37....* (H = 75) Rod ø 10, 7000AB....* Profile mk 2234, 51.80....* Profile mk 2080, 51.80....* 20 12 15 Pg. 270 Profile mk 2239 52.39....* 0.37 kg/m A 138.22 mm 2 mk Systems Profile Technology 115

...* Profile length in mm Function Profiles Conveyor Technology Side Rails Function Profiles Conveyor Technology Other Profile mk 2234 52.34....* 0.82 kg/m A 304.77 mm 2 Profile mk 2007 51.07....* 6.42 kg/m AlMgSi 0.7 F28 A 2381.00 mm 2 Profile mk 2235 52.35....* 0.32 kg/m A 117.05 mm 2 50 50 50 110 150 Profile mk 2236 52.36....* 0.45 kg/m A 166.97 mm 2 Profile mk 2251 52.51....* 3.62 kg/m AlMgSi 0.7 F28 A 1341.17 mm 2 Profile mk 2237 52.37....* 0.59 kg/m A 216.87 mm 2 116 mk Systems Profile Technology

...* Profile length in mm 38.5 69 90 Profile mk 20.76 54.76....* 3.02 kg/m A 1119.00 mm 2 41 60 Profile mk 2253 52.53....* 1.78 kg/m A 660.00 mm 2 Profile mk 2254 52.54....* 2.08 kg/m A 767.00 mm 2 mk Systems Profile Technology 117

...* Profile length in mm Function Profiles Triggers and Sliders Profiles mk 22 and mk 2241 have multiple uses in Series and 50 applications. To install these profiles, countersunk holes must be placed at appx. 300 mm intervals. Application example for sliding door 16 7 27 Profile mk 22 52.....* 0.47 kg/m A 173.35 mm 2 Application example for triggers 7 16 Profile mk 2241 52.41....* 0.67 kg/m A 248.65 mm 2 FH-SHCS M4 x12, DIN7991, D7991412 Nut 1 M4, Steel Zn, 34.08.0001 118 mk Systems Profile Technology

...* Profile length in mm Function Profiles Planning and Information Boards Standard mk profile system components, in combination with profiles mk 20.71 and mk 20.72, can be used to manufacture planning or information stations. Both profiles interlock and can be expanded as desired. When used with System and 50, the profiles are simply slid into the available T-slots. Profile mk 20.71 54.71....* 1.57 kg/m A 583.00 mm 2 Profile mk 20.77 54.77....* 0.51 kg/m A 187.17 mm 2 mk Systems Profile Technology 119

...* Profile length in mm Function Profiles Drawing Holders mk drawing holders offer a clean and simple way to display technical drawings, large format layouts, or method and instruction sheets. By using just a handful of components, this information can be effectively organized, leaving an uncluttered operator workplace. Any size drawings can be inserted. They can be used singly or, for larger formats, used in combination by sliding them together. Depending on the profile selected, up to six rows can be utilized. Angel E25s 82..0741, Al SHCS M8x16 DIN 912 D0912816, 8.8 Zn Nut 1 PE M8 34.01.0018 Profile mk 2025.45 25.45....* 0.48 kg/m A 175.59 mm 2 Profile mk 2025.46 25.46....* 0.31 kg/m A 114.4 mm 2 mk 2025.41 mk 2025.42 Drawing Rail B34.02.010 mk 2025.43 mk 2025.44 120 mk Systems Profile Technology

...* Profile length in mm Function Profiles 19'' Rack Profiles to attach standard 19" electronic racks within frames and enclosures made with mk Profile Systems. 72.6 Profile mk 2025.23 25.23....* 1.76 kg/m 15.5 48 A 652.98 mm 2 42.5 50 Nut 1 M6, Steel Zn, 25.50.0512 Hex Head Screw M6, D0933610 Telescoping Rail 41 34.5 22 47 Profile mk 2025.24 25.24....* 1.28 kg/m A 475.48 mm 2 mk Systems Profile Technology 121

...* Profile length in mm Function Profiles Cover and Connection Profiles ex. for Alucobond panels 3 7 10.5 Profile mk 2205 52.05....* 0.12 kg/m 4 8 13.5 Profile mk 2206 52.06....* 0.14 kg/m 6 11 20 Profile mk 2207 52.07....* 0.27 kg/m 13 8 20 Profile mk 2208 52.08....* 0.28 kg/m 122 mk Systems Profile Technology

...* Profile length in mm Profile mk 2209 52.09....* 0.19 kg/m 25.5 4 8 Profile mk 2214 52.14....* 0.25 kg/m Profile mk 2210 52.10....* 0.25 kg/m 38 6 11 Profile mk 2215 52.15....* 0.47 kg/m 6 29 20 Profile mk 2211 52.11....* 0.47 kg/m 38 Profile mk 2216 52.16....* 0.48 kg/m 8 13 8 31 20 Profile mk 2212 52.12....* 0.48 kg/m 28 4 13.5 Profile mk 2203 52.03....* 0.62 kg/m 8 19.5 4 6 3 7 Profile mk 2213 52.13....* 0.19 kg/m 30 15 4 30 Profile mk 2204 52.04....* 0.62 kg/m mk Systems Profile Technology 123

...* Profile length in mm Function Profiles Partitions Profile mk 20.83 54.83....* 4.10 kg/m 80 A 1517.19 mm 2 Ix 135.57 cm 4 Iy 101.46 cm 4 Wx 33.89 cm 3 Wy 23.29 cm 3 80 Wireway ex. for partitions 50 54 Profile mk 20.84 54.84....* 0.36 kg/m A 134.86 mm 2 8 Profile mk 20.47 54.47....* 1.82 kg/m Spacer 14.00.0007, Al Spring 07.13.0001, Spring steel 74 80 A 674.22 mm 2 Ix 6.55 cm 4 Iy 50.26 cm 4 Wx 2.37 cm 3 Wy 12.55 cm 3 Profile for flush fit to floor, wall or ceiling Profile mk 20.48 54.48....* 0.72 kg/m A 264.78 mm 2 73 124 mk Systems Profile Technology

...* Profile length in mm Function Profiles Swing Door Stops With profiles mk 20.88 and mk 20.25 door stops can be placed into partitions or guarding systems for the two most common door styles. The profiles can be placed around the entire perimeter of the door, and the seal strips serve to both dampen and seal the door upon closing. 45 15 20 Profile mk 20.88 54.88....* 0.67 kg/m A 247. mm 2 Seal Strip mk 3025 25 41 25 Profile mk 20.25 54.25....* 0.50 kg/m A 186.50 mm 2 Seal Strip mk 3025 20 5 mk Systems Profile Technology 125

...* Profile length in mm Function Profiles Guarding Profile mk 2218 52.18....* 1.15 kg/m A 425.081 mm 2 Light-duty fence clamping Profile mk 2217 52.17....* 0.13 kg/m A 48.33 mm 2 Normal fence clamping Profile mk 20.60, Al Corner Clip 14.00.0004, PE Fencing x x 4 or Paneling 5 mm Sheet Metal Screw ø 3.5 x 25 K112510014, Steel (for sides over 1500 mm) 6.5 35 11 Profile mk 20.60 54.60....* 0.30 kg/m A 112.52 mm 2 126 mk Systems Profile Technology

...* Profile length in mm Function Profiles Steps, Flooring and Facades Special profiles for the manufacture of steps, machine platforms and mezzanines as well as facades for office interiors and trade shows. 102 80 Profile mk 20.68 54.68....* 2.37 kg/m A 880.53 mm 2 ø 7 41 20 20 76 100 152 130 Profile mk 20.69 54.69....* 2.87 kg/m A 1066.31 mm 2 ø 7 41 20 20 126 150 2 ø 7 200 Profile mk 20.26 54.26....* 3.78 kg/m A 1398.84 mm 2 mk Systems Profile Technology 127

...* Profile length in mm Function Profiles Windows Through various combinations of panel profiles and seal strips, panels of various thicknesses can be installed. These profiles are used primarily with 80 mm wide Series structural profiles. The seal strips are silicone free. 7 Profile mk 20.81 54.81....* 0.28 kg/m 5 25 A 104.68 mm 2 17 Seal Strip mk 3020 for Gap 5-6 mm EPDM 2 5 25 Profile mk 20.82 54.82....* 0.31 kg/m A 114.68 mm 2 Seal Strip mk 3021 for Gap 7-8.5 mm 17 EPDM Seal Strip mk 3023 for Gap 10 mm EPDM 12 20 Profile mk 20.59 54.59....* 0.26 kg/m A 96.17 mm 2 Seal Strip mk 3024 for Gap 12 mm EPDM Seal Strip mk 3033 for Gap 4 mm EPDM Profile mk 20.97 54.97....* 0.3733 kg/m A 138.24 mm 2 128 mk Systems Profile Technology

Examples...* Profile length in mm Panel width 6 mm Panel width 18 mm Profile mk 20.80, 54.80....* Profile mk 20.82, 54.82....* Seal Strip, mk 3024 Paneling Profile mk 20.80, 54.80....* Profile mk 20.82, 54.82....* Seal Strip, mk 3020 Paneling Panel width 8 mm Profile mk 20.80, 54.80....* Profile mk 20.82, 54.82....* Seal Strip, mk 3024 Seal Strip, mk 3023 Paneling Panel width 20 mm Profile mk 20.80, 54.80....* Profile mk 20.81, 54.81....* Seal Strip, mk 3023 Paneling Panel width 10 mm Panel width 30 mm Profile mk 20.80, 54.80....* Profile mk 20.82, 54.82....* Seal Strip, mk 3023 Paneling Profile mk 20.80, 54.80....* Profile mk 20.81, 54.81....* Seal Strip, mk 3020 Paneling Panel width 12 mm Panel width 50 mm Profile mk 20.80, 54.80....* Profile mk 20.82, 54.82....* Seal Strip, mk 3021 Seal Strip, mk 3023 Profile mk 20.80, 54.80....* Profile mk 20.81, 54.81....* Seal Strip, mk 3021 Paneling Paneling Panel width 15 mm Panel width 74 mm Profile mk 20.80, 54.80....* Profile mk 20.82, 54.82....* Seal Strip, mk 3021 Profile mk 20.80, 54.80....* Profile mk 20.59, 54.59....* Paneling Paneling mk Systems Profile Technology 129

...* Profile length in mm Function Profiles Wireways mk Wireways offer an alternative to the usual electronic and power supply covers. The are extremely functional and integrate neatly with mk profile systems. Further information can be found on page 256 Profile mk 20.50 54.50....* 0.51 kg/m Profile mk 20.51 54.51....* 0.67 kg/m Clip 01, 54.49.0030 Band, K115010217 80 Clip 02, 5449BA0030 Cable Tie, K399000002 50 25 Profile mk 2050 51.50....* 0.43 kg/m Profile mk 2051 51.51....* 0.56 kg/m 50 Profile mk 2048 51.48....* 0.30 kg/m Profile mk 20.49 54.49....* 0.30 kg/m 130 mk Systems Profile Technology

...* Profile length in mm Profiles for Rework Rework Profiles for rework are the raw material for many of our standard components. They are also available for use in manufacturing customer-specific components. As a rule, these profiles are not anodized. Profile mk 20.99 54.99....* 1.30 kg/m AlMgSi 0.7 F28 A 478.85 mm 2 Hinges Profile mk 20.61 54.61....* 0.80 kg/m AlMgSi 0.7 F28 A 295.48 mm 2 Profile mk 2025.47 25.47....* 0.89 kg/m AlMgSi 0.7 F28 A 329.62 mm 2 Profile mk 2043 51.43....* 0.94 kg/m AlMgSi 0.7 F28 A 346.46 mm 2 6 12.5 4.5.5 ø 8 Profile mk 2025.82 25.82....* 0.68 kg/m AlMgSi 0.7 F28 A 250.73 mm 2 Profile mk 2029 51.29....* 1.45 kg/m AlMgSi 0.7 F28 A 536.44 mm 2 ø 15 Profile mk 20.98 54.98....* 1.24 kg/m AlMgSi 0.7 F28 A 458.88 mm 2 9 75 Profile mk 2090 51.90....* 2.75 kg/m AlMgSi 0.7 F28 A 1018.17 mm 2 29.6 mk Systems Profile Technology 131

...* Profile length in mm Profiles for Rework Hinges Profile mk 2060.82 60.82....* 1.08 kg/m 10.3 80.3 10.3 Profile mk 2098 51.98....* 2.94 kg/m AlMgSi 0.7 F28 A 1087.91 mm 2 AlMgSi 0.7 F28 A 399.36 mm 2.3 15.3 85.3 Profile mk 2085 51.85....* 6.21 kg/m AlMgSi 0.7 F28 A 2300.95 mm 2 50 Profile mk 20.55 54.55....* 1.80 kg/m 15.3 20 20 A 667.58 mm 2 85.3 Angles 30 30 10.3.3 10.3 Profile mk 2088 51.88....* 1.08 kg/m AlMgSi 0.7 F28 A 399.86 mm 2 Profile mk 2097 51.97....* 1.88 kg/m AlMgSi 0.7 F28 A 696.77 mm 2 50.3 15 15.3 50 85.3 15.3 15 ø7 Profile mk 2089 51.89....* 4.80 kg/m AlMgSi 0.7 F28 A 1776. mm 2 Profile mk 2081 51.81....* 2.68 kg/m AlMgSi 0.7 F28 A 993.95 mm 2.3 50 132 mk Systems Profile Technology

...* Profile length in mm Profile mk 2060.71 60.71....* 3.91 kg/m AlMgSi 0.7 F28 A 1445.58 mm 2 Profile mk 2052 51.52....* 3.20 kg/m A 1235.00 mm 2 Profile mk 2060.72 60.72....* 6.45 kg/m AlMgSi 0.7 F28 A 2387.46 mm 2 Profile mk 2053 51.53....* 3. kg/m A 1252.00 mm 2 Profile mk 2060.73 60.73....* 8.97 kg/m AlMgSi 0.7 F28 A 3319.42 mm 2 Profile mk 2054 51.54....* 3.36 kg/m A 1243.05 mm 2 mk Systems Profile Technology 133

...* Profile length in mm Profile for Swivels 23.4 45 30 Profile for Wedges Profile mk 20.62 54.62....* 3.02 kg/m AlMgSi 0.7 F28 A 1119.85 mm 2 80 Profile mk 20.65 54.65....* 4.32 kg/m AlMgSi 0.7 F28 A 1601.54 mm 2 Further 10 50 54 70 Profile for Carriage Wagons Profile mk 2070 51.70....* 3.86 kg/m AlMgSi 0.7 F28 A 1431.43 mm 2 Profile for Base Plates Profile mk 20.27 54.27....* 6.48 kg/m AlMgSi 0.7 F28 A 2.00 mm 2 R20 Profile for Hand Rails 17.6 Profile mk 20.63 54.63....* 1.46 kg/m AlMgSi 0.7 F28 A 543.72 mm 2 10 Profile for Swivels 19 45 20 Profile for Wedges 9 65 Profile mk 2084 51.84....* 2.64 kg/m AlMgSi 0.7 F28 A 980.50 mm 2 55 Profile mk 20.66 54.66....* 2.09 kg/m 15 50 AlMgSi 0.7 F28 A 775.30 mm 2 134 mk Systems Profile Technology

...* Profile length in mm Profile for Covers 6 10 Profile for Machining Table Profile mk 2250 52.50....* 1.30 kg/m A 466.9 mm 2 Profile for Floor Brackets 202 50 50 50 15 Profile mk 2095 51.95....* 10.54 kg/m AlMgSi 0.7 F28 A 3903.37 mm 2 Profile mk 2271 52.71....* 3.67 kg/m 32 A 1417.23 mm 2 Profile for Clamps Profile mk 2074 51.74....* 0.97 kg/m A 361.84 mm 2 Profile for Locks 15 Profile for Connectors 45 Profile mk 20.87 54.87....* 1.51 kg/m A 559.35 mm 2 29.7 Profile mk 20.78 54.78....* 0.72 kg/m A 266.69 mm 2 ø 24 30 ø 5 30 Profile for Height Adjustments Profile mk 20.36 54.36....* 2.83 kg/m AlMgSi 0.7 F28 A 1049.01 mm 2 23 29.8 48 13.5 Profile for Connectors Profile mk 20.79 54.79....* 1.45 kg/m A 536.30 mm 2 mk Systems Profile Technology 135

...* Profile length in mm Profile for Connectors Profile for Couplings 88 Profile mk 20.89 54.89....* 2.17 kg/m A 802.16 mm 2 ø Profile mk 2046 51.46....* 2.94 kg/m AlMgSi 0.7 F28 A 1087.85 mm 2 15 Profile for Couplings 20 20 Profile for Parallel Connectors Profile mk 2096 51.96....* 0.71 kg/m AlMgSi 0.7 F28 A 262.74 mm 2 ø 80 ø 60 Profile mk 2047 51.47....* 6.95 kg/m AlMgSi 0.7 F28 A 2575.22 mm 2 Profile for Drums Profile for Handles Profile mk 2244 52.44....* 0.87 kg/m A 321.16 mm 2 Profile mk 2231 52.31....* 4.61 kg/m AlMgSi 0.7 F28 A 1706.18 mm 2 Profile as C-channel Profile mk 2245 52.45....* 1.54 kg/m A 569.00 mm 2 ø 100 Profile for Drums Profile mk 2232 52.32....* 5.77 kg/m AlMgSi 0.7 F28 A 2137.24 mm 2 136 mk Systems Profile Technology

Further Function Profiles...* Profile length in mm Profile for Swivels Profile mk 2246 52.46....* 4.12 kg/m Profile for Clamps Profile mk 2294 52.94....* 1.6 kg/m AlMgSi 0.7 F28 A 592.56 mm 2 A 1526.85 mm 2 Profile for Clamps Profile for Corner Block Profile mk 2248 52.48....* 3.50 kg/m Profile mk 2295 52.95....* 1.66 kg/m AlMgSi 0.7 F28 A 615.95 mm 2 A 1289.00 mm 2 Profile for Clamps Profile mk 2296 52.96....* 0.89 kg/m A 328.89 mm 2 214 Profile for Stand Profile mk 2270 52.70....* 5.65 kg/m AlMgSi 0.7 F28 A 2093.80 mm2 21.5 30 26.5 Profile for Clamps Profile mk 2038 51.38....* 1.78 kg/m AlMgSi 0.7 F28 A 661.46 mm 2 Profile for Pallets Profile mk 2093 51.93....* 0.95 kg/m AlMgSi 0.7 F28 A 349.76 mm 2 mk Systems Profile Technology 137

...* Profile length in mm Other Function Profiles 8 13 22 36.2 37 Profile for Blinds Profile mk 2079 51.79....* 0.28 kg/m A 106.00 mm 2 Profile for Surface Clamps Profile mk 2062 51.62....* 0.74 kg/m AlMgSi 0.5 F28 A 276.01 mm 2 30 30 38 22.5 Profile for Clamps Profile mk 20.64 54.64....* 1.42 kg/m A 529.01 mm 2 Profile for Conveyor Stands Profile mk 2030 51.30....* 1.06 kg/m AlMgSi 0.7 F28 A 394.46 mm 2 Profile for Foot Rests Profile mk 20.70 54.70....* 3.53 kg/m AlMgSi 0.7 F28 A 1307.35 mm 2 138 mk Systems Profile Technology

...* Profile length in mm 160 Profile for Pallets Profile mk 2049 51.49....* 4.66 kg/m A 1739.50 mm2 Profile mk 20.54 54.54....* 1.041 kg/m A 385.39 mm 2 2.5 20 5.2 50.8 Profile mk 2060.81 60.81....* 0.754 kg/m AlMgSi 0.7 F28 A 279.4 mm 2 Profile for Sound Damping 76 Profile mk 2219 52.19....* 1.14 kg/m A 421.25 mm2 30 Profile mk 2073 51.73....* 0.38 kg/m 15 6 AlMgSi 0.7 F28 A 142.69 mm 2 22 ø 16.5 22 44.5 18 35 Profile mk 2063 51.63....* 1.83 kg/m AlMgSi 0.7 F28 A 1733.00 mm 2 20 7 9.5 Profile mk 2083 51.83....* 0.43 kg/m AlMgSi 0.7 F28 A 160.49 mm 2 80 ø22 Profile mk 2064 51.64....* 4.63 kg/m AlMgSi 0.7 F28 A 1716.37 mm 2 10 28.3 Profile mk 2087 51.87....* 0.51 kg/m AlMgSi 0.7 F28 A 189.74 mm2 18 10 mk Systems Profile Technology 139

mk Assembly Components Overview Connectors 142 Angles Consoles 165 General Information 144 Series 25 146 Series 148 Series 50 151 Series 60 159 Adjustable Angles 162 Angle Positioner 164 Internal Fasteners 172 Plates 175 Corner Blocks 187 Parallel Connectors 196 Profile Connectors 197 Clamps 198 Nuts 200 Grounding 204 Screws, Nuts and Washers 205 mk Systems Profile Technology 141

Overview Connectors Angles Page 144 Adjustable Angles Page 162 Consoles Page 165 Tension Plugs Page 172 Economy Fastener Page 173 Swivel Tension Plugs Page 174 142 mk Systems Profile Technology

Face Plates Page 175 Plates Page 176 Corner Blocks Page 187 Parallel Connectors Page 196 Profile Connectors Page 197 Clamps Page 198 mk Systems Profile Technology 143

General Information for Angles mk Angles mk Angles are manufactured from extruded aluminum profiles (AlMgSi 0.7 F28) and are milled perpendicular. They have a tumbled surface finish. We can also manufacture special angles using our angle profiles. mk Keyed Angles The keys in Angles Bs, Cs, Ds, Es, Fs, Gs and S firmly hold the angle in the T-slot, thus preventing any rotation of the profile. In an assembly you can be assured of exact 90 connection. mk Angles are our most popular components. They also offer the possibility of attaching profiles from different series. M8 threads can be cut into the extruded holes on the sides of most angles. (ex. Angle B to attach paneling) 144 mk Systems Profile Technology

Examples Angle Series 25 Profile mk 2025.05, mk 2025.02 2 Angle A25//1 Series Profile mk 2025.02 Angle A25//2 Profile mk 2025.25, 2025.01 Angle A25/15/2 Profile mk 20.02, 20.03 2 Angle E80 Series 50 Profile mk 20.02 Angle F80 Profile mk 20.04, 20.01 Angle G Profile mk 2005, mk 2004 2 Angle B100 Series 60 Profile mk 2004 Angle D90/2 Profile mk 2072, mk 2000 Angle C/2 Profile mk 2060.02, mk 2060.05, Angle H100 Profile mk 2060.02, Angle J100 Profile mk 2060.01, mk 2060.22 Angle K100 mk Systems Profile Technology 145

Angles Series 25 with Rib Washer Angle 15 25.50.1000 Angle 15, 25.50.1000 Angle 25.50.1001 SHCS DIN 6912, M5 x 10 8.8 Zn D6912510 Rib Washer, ø 8.4 K111010015 Nut M5, Steel Zn, 25.05.0500 Angle 90 25.50.1002 Angle 1 25.50.1003 146 mk Systems Profile Technology

Angle A25/15/2 25.50.1020 Angle S15 25.50.1010 Angle A25//2 25.50.1021 Angle S 25.50.1012 M5 Angle B25/15/1 25.50.1050 M8 Angle E25/20/1 25.50.1030 mk Systems Profile Technology 147

Angles Series Angle E 12.5 25 ø7 Angle E25 82..0701 20 10 10 Angle E 82..0702 Angle E25, 82..0701 SHCS DIN 912, M8 x 16 8.8 Zn D0912816 12.5 Rib Washer, ø 8.4 K111010017 Nut 1 M8, Steel Zn, 34.01.0001 20 20 65 Angle E65 82..0704 20 20 80 Angle E80 82..0703 20 Angle E120 82..0705 148 mk Systems Profile Technology

Angle Es Angle F 12.5 ø 8.4/13.5 Angle E25s 82..0741 80 Angle F25 82..0801 25 9 9 ø 8.4/13.5 Angle Es 82..0742 Angle Es3 82..0747 10 20 10 ø7 Angle F 82..0802 12.5 39 39 65 Angle E65s 82..0744 12.5 Angle F65 82..0804 12.5 Angle E105s 82..0745 20 20 65 39 20 39 105 Angle F80 82..0803 12.5 Angle E145s 82..0746 20 20 80 39 39 145 mk Systems Profile Technology 149

Angle Fs Angle G 10 12,5 79 Angle F25s 82..0841 Angle G65 82..0904 39 25 20 65 12,5 10 20 79 Angle F65s 82..0844 Angle G80 82..0903 39 65 20 20 80 Angle G Angle Gs 12,5 10 80 20 10 80 25 Angle G25 82..0901 Angle G 82..0902 79 79 12,5 10 79 25 Angle G25s 82..0941 Angle G65s 82..0942 10 79 65 150 mk Systems Profile Technology

Angles Series und 50 Angles L, M and N are ideally suited for bracing machine frames. They are available in 30, 45 and 60 standards. Angle L25 82.10.01 Angle M25 82.11.01 Nut 1 M8, Steel Zn, 34.01.0001 Ribbed Washer, ø 8.4 K111010017 SHCS DIN 912, M8 x20, 8.8 Zn D0912820 e.g. Angle 82.11.01 Angle N25 82.12.01 mk Systems Profile Technology 151

Angle L25s 82.10.41 Angle M25s 82.11.41 Angle N25s 82.12.41 152 mk Systems Profile Technology

Angles Series 50 Angle A Angle A1 82.02.0001 Angle B25, 82.05.0003 Angle A2 82.02.0002 SHCS DIN 912, M8 x 20, 8.8 Zn D0912820 Rib Washer, ø 8.4 K111010017 Nut 1 M8, Steel Zn, 34.01.0001 Angle A3 82.03.0001 Angle A4 82.03.0002 mk Systems Profile Technology 153

Angle B ø 8.5/13.5 Angle B25 82.05.0003 Angle B70 82.05.0010 Angle B 82.05.0013 Angle B90 82.05.0022 Angle B50 82.05.0004 Angle B100 82.05.0006 Angle B50/1 82.05.0009 Angle B150 82.05.0012 Angle B50/2 82.05.0005 Angle B200 82.05.0011 154 mk Systems Profile Technology

Angle Bs Angle Bs2 82.05.0055 Angle C90 82.06.0003 Angle B50s1 82.05.0051 Angle B50s2 82.05.0052 Angle C1 82.06.0004 Angle B50s3 82.05.0053 Angle C Angle C25 82.06.0001 Angle C/1 82.06.0005 Angle C 82.06.0002 Angle C90/1 82.06.0006 mk Systems Profile Technology 155

Angle Cs Angle C1/1 82.06.0007 Angle C25s 82.06.00 Angle C/2 82.06.0008 Angle Cs 82.06.0041 Angle C90/2 82.06.0009 Angle C90s 82.06.0042 Angle C1/2 82.06.0010 Angle C1s 82.06.0043 156 mk Systems Profile Technology

Angle D ø 8.4/13.5 Angle D25 82.07.0001 Angle D90/1 82.07.0006 Angle D 82.07.0002 Angle D90/2 82.07.0009 Angle D/1 82.07.0005 Angle D1 82.07.0004 Angle D/2 82.07.0008 Angle D90 82.07.0003 Angle D1/1 82.07.0007 mk Systems Profile Technology 157

Angle D1/2 82.07.0010 Angle Ds Angle D25s 82.07.00 Angle D90s 82.07.0042 Angle D1s 82.07.0043 158 mk Systems Profile Technology

Angles Series 60 Angle H Angle H 82.60.0701 Angle H, 82.60.0701 SHCS DIN 912, M12 x 25, 8.8 Zn D09121225 Angle H100 82.60.0702 Rib Washer, ø 12.9 K111010019 Nut 1 M12, Steel Zn, 34.60.0101 Angle H160 82.60.0703 mk Systems Profile Technology 159

Angle Hs Angle Hs 82.60.0741 Angle J160 82.60.0803 Angle H100s 82.60.0742 Angle Js 60 Angle J Angle Js 82.60.0841 Angle J 82.60.0801 Angle J100s 82.60.0842 Angle J100 82.60.0802 160 mk Systems Profile Technology

Angle K Angle K 82.60.0901 Angle Ks 82.60.0941 Angle K100 82.60.0902 Angle K100s 82.60.0942 Angle K160 82.60.0903 mk Systems Profile Technology 161

Angles Adjustable Angles allow the attachment of profiles at non-standard angles. If desired, the angles can be pinned to a preset position prior to assembly. Usable range is 45-205. Adjustable Angle Wing A25/1 25.50.1101 Installation example Series Rib Washer ø 8.4 Zn, K111010017 Nut 1 M8, Steel Zn, 34.01.0001 Hex Head Screw, DIN 933, M8 x 20, 8.8 Zn, D0933820 Adjustable Angle Wing A25/2 25.50.1103 Adjustable Angle Wing B25 82.07.0021 SHCS DIN 912, M8 x 12, 8.8 Zn, D0912812 Hex Nut M8 DIN 934, 8 Zn, (pressed in) D09348 *Spring Pin 4 x 24, DIN1481 D1481424 Adjustable Angle Wing D25 82.07.0020 *Order separately. Angles can be pinned at pre-set positions. 162 mk Systems Profile Technology

35 60 ø 6.6 25 Adjustable Angle A25/1 B46.00.035 as shown 25 25 Adjustable Angle C25 B46.00.037 as shown B46.00.025 complete with attachment hardware B46.00.027 complete with attachment hardware 60 25 25 Adjustable Angle A25/2 B46.00.036 as shown B46.00.026 complete with attachment hardware 60 25 25 Adjustable Angle D25 B46.00.032 as shown B46.00.020 complete with attachment hardware 60 25 Adjustable Angle A25/3 B46.00.034 as shown 25 B46.00.024 complete with attachment hardware 35 ø 8.4 25 Adjustable Angle B25 B46.00.033 as shown B46.00.021 complete with attachment hardware mk Systems Profile Technology 163

Angles Angle Positioner When used with the Spindle and Anchor Block, Angle can be positioned over a range of 10 mm. This is helpful in applications requiring fine-tuning or exact placement of components or profiles. The Spindle thread is M8x1 which translates into 1 revolution = 1 mm horizontal travel. Angle Positioner B50s3 B85.01.001 complete with attachment hardware Angle, 82.05.0060 Range appx. 10 mm M8x1 Angle 82.05.0060 Nut 1 M8, 34.01.0001 M8x1 Spindel 71.00.0002 Steel Zn Anchor Bock, 35.02.0017 SHCS M8 x16, DIN 912, 8.8 Zn, D0912816 Anchor Block 35.02.0017 Spindle, 71.00.0002 164 mk Systems Profile Technology

Consoles Cast Consoles Series 50 For frames with high static loads, the mk Consoles are a sound alternative to the mk Angles. The Consoles are cast aluminum and milled square. Console 3 31.00.0003 Console 3/2 31.02.0003 undrilled Weight 0.65 kg Console 1 31.00.0001 Console 1/2 31.02.0001 undrilled Weight 0.25 kg Console 4 31.00.0004 Console 2 31.00.0002 Console 2/2 31.02.0002 undrilled Weight 0.50 kg Console 4/2 31.02.0004 undrilled Weight 0.35 kg mk Systems Profile Technology 165

Console 5 31.00.0005 Console 5/2 31.02.0005 undrilled Weight 0.70 kg Console 7 Keyed 31.00.0007 Weight 0. kg Console 6 31.00.0006 Console 6/2 31.02.0006 undrilled Weight 1.00 kg Console 17 31.00.0017 Console 17/2 31.02.0017 undrilled Weight 2.30 kg 166 mk Systems Profile Technology

Console 14 31.00.0014 Console 14/2 31.02.0014 undrilled Weight 0.70 kg Console 16/ 31..0016 Console 15 31.00.0015 Console 15/2 31.02.0015 undrilled Weight 1.20 kg Console 16 31.00.0016 Console 16/2 31.02.0016 undrilled Weight 1,60 kg mk Systems Profile Technology 167

Consoles Cast Consoles Series 60 For framing with high static loads, mk consoles are a heavier duty alternative to angles. They are made of cast aluminum and milled square. Console 60/1 31.60.0001 Cast alu Nut 1 M12, Steel Zn 34.60.0301 SHCS DIN 6912, M12 x 30 8.8 Zn, D69121230 Rib Washer ø 12, Spring Steel Zn K111010019 Console 60/2 31.60.0002 Cast alu 168 mk Systems Profile Technology

Console 60/4 31.60.0004 Cast alu Console 60/7 31.60.0007 Cast alu Console 60/5 31.60.0005 Cast alu Console 60/8 31.60.0008 Cast alu mk Systems Profile Technology 169

Consoles Connecting Consoles As parallel connectors of load bearing beams, for example, mk Connecting Consoles provide a high load capacity. Console 52 31.00.0025 Weight 1.30 kg, Cast Aluminum Nut 3/50 M8, 34.01.0006 Rib Washer ø 8.4, Spring Steel Zn, K111010017 SHCS M8 x 20, DIN 912, 8.8 Zn, D0912820 Console 51 31.00.0024 Weight 1.90 kg, Cast Aluminum 170 mk Systems Profile Technology

Consoles Floor Consoles mk Floor Consoles ensure a stable base, or a secure attachment for frames to the shop floor, for example. Console 54 compensates for uneven flooring and has an adjustment range of +/- 18 mm. Console 54 B67.02.037 Weight 10 kg, Console Cast Iron, Pad Steel Console 55 31.00.0028 Weight 3 kg, Cast Aluminum mk Systems Profile Technology 171

Internal Fasteners Tools can be found on page 290 Tension Plug Series 25 Tension Plug Series 50 Tension Plug Series 25 B51.03.009 Steel Zn Tension Plug for mk 2000 B51.03.006 Tension Plug Series Drill Fixtures A Tension Plug Series B51.03.004 Steel Zn B51.03.030 Stainless Steel Drill Fixture D* A* Order-Nr. Series 25 5.8 15 B46.03.001 Series 10 15 B51.03.005 Series 50 10 15 B51.03.005 *Values in mm 172 mk Systems Profile Technology

Internal Fasteners Economy Fastener The economy fastener allows users the option of assembling profile frames without any special connecting elements. All components are readily available DIN parts. The primary application of this fastener is in the areas of guarding and light-duty framing. SHCS D6912820 DIN 6912, 8.8 Zn D6912820A2 DIN 6912, Stainless Steel SHCS DIN 6912, M8 x 20, Stainless Steel, D6912820A2 Spring Washer ø 8.4, Stainless Steel, D67968.4A2 Ensat M8 Threaded insert, K112030020, Stainless Steel Spring Washer D67968 St Zn D67968.4A2 Stainless Steel Drill Fixture Drill Fixture Flat Finish B51.03.020 mk Systems Profile Technology 173

Internal Fasteners Swivel Tension Plug Swivel Tension Plug Series B51.03.011 Steel Zn, 90-270 B51.03.031 Stainless Steel, 90-270 Swivel Tension Plug Series, Steel Zn, B51.03.011 Swivel Tension Plug Series 25 B51.03.010 Steel Zn 90-270 Swivel Tension Plug Series 25, Steel Zn, B51.03.010 174 mk Systems Profile Technology

Plates Face Plates Connecting plates for assembly at profile ends Face plates are primarily used to mount profiles into existing framing. The plates feature keyways to prevent twist, and the included hardware is designed for drop-in use. Face Plate B46.07.090 AL tumbled, mounting hardware SHCS DIN 7984, 8.8 Zn, M8 x 20, D7984820 Plate, 50.05.0090 T-Nut M6, 34.07.0006 SHCS DIN 912, 8.8 Zn, M6 x 20, D0912620 Face Plate 50 B46.07.095 AL tumbled, for Profile mk 2000 incl. mounting hardware mk Systems Profile Technology 175

Plates Series 25 45 25 20 ø 5.5 Straight Plate 01 25.50.3000 4 Flanged Button-Head SHCS M5 x 10, 10.9 Zn, K112010021 Nut M5, Steel Zn, 25.50.0500 25 70 25 20 Straight Plate 02 25.50.3001 20 25 25 45 T-Plate 01 25.50.3006 50 70 176 mk Systems Profile Technology

45 25 25 45 Angle Plate 01 25.50.3002 Plate 01 25.50.3100 Undrilled 20 25.50.3110 70 50 20 20 50 70 Junction Plate 01 25.50.3007 Plate 02 25.50.3101 Undrilled 25.50.3111 Plate 03 25.50.3102 Undrilled 25.50.3112 mk Systems Profile Technology 177

Plates Series and 50 39 ø9 Straight Plate 05 50.05.0053 4 70 65 Nut 1 M8, Steel Zn, 34.01.0001 Flanged Button-Head SHCS M8 x 12, 10.9 Zn, K112010002 95 39 Straight Plate 03 50.05.0052 12 4 50 128 50 39 ø9 Straight Plate 07 50.05.0047 178 mk Systems Profile Technology

14.5 50 160 65 84 50 65 39 50 50 128 84 50 50 84 39 39 Straight Plate 09 50.05.0070 T-Plate 03 50.05.0046 Angle Plate 03 50.05.0045 120 150 39 14.5 50 50 39 50 Angle Plate 11 50.05.0067 Angle Plate 13 50.05.0051 Angle Plate 15 50.05.0068 39 mk Systems Profile Technology 179

Plate /8 50.05.0066 50.05.0166 Undrilled Plate /4 50.05.0062 50.05.0162 Undrilled Plate /7 50.05.0065 50.05.0165 Undrilled Plate /2 50.05.0060 50.05.0160 Undrilled 180 mk Systems Profile Technology

Plates /120 and /160 feature a key step, through with the plates remain aligned with the T-slots during installation. Plate /3 50.05.0061 50.05.0161 Undrilled Plate /120 50.05.0056, Key width 10 mm Plate /6 50.05.0064 50.05.0164 Undrilled Plate /160 50.05.0057, Key width 10 mm mk Systems Profile Technology 181

Plate 10 50.05.0010 50.05.0110 Undrilled Plate 12 50.05.0012 50.05.0112 Undrilled Plate 11 50.05.0011 50.05.0111 Undrilled 182 mk Systems Profile Technology

Plate 13 50.05.0013 50.05.0113 Undrilled Plate 15 50.05.0015 50.05.0115 Undrilled Plate 14 50.05.0014 50.05.0114 Undrilled Plate 16 50.05.0016 50.05.0116 Undrilled mk Systems Profile Technology 183

Plate 17 50.05.0017 50.05.0117 Undrilled Plate 19 50.05.0019 50.05.0119 Undrilled Plate 18 50.05.0018 50.05.0118 Undrilled 184 mk Systems Profile Technology

Plates Series 60 Plate 60/10 50.05.6010 Ribbed Washer ø 12 Spring Steel Zn, K111010019 SHCS DIN 912, M12 x 25 8.8 Zn, D09121225 Nut 1 M12, Steel Zn 34.60.0301 Plate 60/12 50.05.6012 mk Systems Profile Technology 185

Plate 60/26 50.05.6026 Plate 60/14 50.05.6014 Plate 60/9 50.05.6009 186 mk Systems Profile Technology

Corner Blocks Series 25 A corner connection which provides a clean connection while increasing the aesthetic appeal of the frame. mk corner blocks are attached at the profile ends. Corner blocks using screws for attachment leave the full T-slots available. These attractive components are ideal for displays, furniture, guarding, etc. Corner Block 25 25.50.3300 Open Connection connects for ex. 2 x Profile mk 2025.01 order hardware separately Closed Connection Threaded insert Ensat M6, 9S20K, K112030006 Ribbed Washer ø 6, Spring Steel Zn, K111010016 SHCS M6 x 16, DIN 6912, 8.8 Zn, D6912616 Corner Block 26 25.50.3301 connects for ex. 3 x Profile mk 2025.01 order hardware separately Nut M6, Steel Zn, 25.50.0512 Set Screw M6 x 8, DIN 914, Steel Zn, D091468 Tension Plug, Steel Zn, 25.50.3321 Corner Block 30 B46.05.001 connects for ex. 2 x Profile mk 2025.01 includes all hardware mk Systems Profile Technology 187

Corner Block 31 B46.05.002 connects for ex. 3 x Profile mk 2025.01 includes all hardware Corner Block 35 B46.05.006 connects for ex. 3 x Profile mk 2025.38 includes all hardware Corner Block 32 B46.05.003 connects for ex. 3 x Profile mk 2025.37 includes all hardware Corner Block 36 B46.05.007 connects for ex. 1 x Profile mk 2025.01 2 x Profile mk 2025.38 includes all hardware Corner Block 33 B46.05.004 connects for ex. 1 x Profile mk 2025.01 2 x Profile mk 2025.37 includes all hardware Corner Block 37 B46.05.008 connects for ex. 2 x Profile mk 2025.01 1 x Profile mk 2025.38 includes all hardware Corner Block 34 B46.05.005 connects for ex. 2 x Profile mk 2025.01 1 x Profile mk 2025.37 includes all hardware Corner Block 38 B46.05.009 connects for ex. 2 x Profile mk 2025.39 includes all hardware 188 mk Systems Profile Technology

Corner Blocks Series A corner connection which provides a clean connection while increasing the aesthetic appeal of the frame. mk corner blocks are attached at the profile ends. Corner blocks using screws for attachment leave the full T-slots available. These attractive components are primarily used for displays, furniture, guarding, etc. Open Connection Ribbed Washer ø 8.4, Spring Steel Zn, K111010017 Threaded insert Ensat M8, 9S20K, K112030008 SHCS M8 x 20, DIN 912, 8.8 Zn, D0912820 Nut M8, Steel Zn, 34.06.0003 Closed Connection 15 Set Screw M8 x 16, DIN 914, Steel Zn, D0914816 Tension Plug, Steel Zn, 05.03.0004 Tools required: Drill ø 10 or Tap M12 x 1.5 see Tools section Pg. 290 15 Drill Fixture B51.03.005 C45K mk Systems Profile Technology 189

Corner Block 6 79.01.0006 connects for ex. 2 x Profile mk 20.01 Corner Block 42 B46.05.043 with Nut, Tension Plug and Set Screw connects for ex. 2 x Profile mk 20.15 1 x Profile mk 20.01 includes all hardware Corner Block 5 79.01.0005 connects for ex. 3 x Profile mk 20.01 Corner Block 41 B46.05.042 with Nut, Tension Plug and Set Screw connects 3 x Profile mk 20.15 includes all hardware Corner Block B46.05.041 with Nut, Tension Plug and Set Screw connects for ex. 2 x Profile mk 20.11 includes all hardware Corner Block 43 B46.05.044 with Nut, Tension Plug and Set Screw connects 3 x Profile mk 20.14 includes all hardware Corner Block 39 B46.05.0 with Nut, Tension Plug and Set Screw connects 3 x Profile mk 20.11 Corner Block 44 B46.05.045 with Nut, Tension Plug and Set Screw connects for ex. 2 x Profile mk 20.14 1 x Profile mk 20.01 includes all hardware includes all hardware 190 mk Systems Profile Technology

Corner Blocks Angle Blocks In combination with profiles mk 20.18/19/20 the angles blocks ensure an aesthetically high quality connection. With the 120, 135 and 150 angles even complex frames are realizable. Further information can be found on page 45 M8 Angle Block 120 for Profile mk 20.18 79.01.0033 Set Screw M8 x 16, DIN 914, Steel Zn, D0914816 Nut M8, Steel Zn, 34.06.0003 Tension Plug, Steel Zn, 05.03.0004 120 20 Angle Block 47 B46.05.047 includes all hardware A View A-A M8 15 135 Angle Block 135 for Profile mk 20.19 79.01.0035 20 Angle Block 48 B46.05.048 includes all hardware 120 M8 A Threaded insert Ensat M8, 9S20K, K112030008 SHCS M8 x 20, DIN 912, 8.8 Zn, D0912820 150 20 Angle Block 150 for Profile mk 20.20 79.01.0037 Angle Block 49 B46.05.049 includes all hardware mk Systems Profile Technology 191

Corner Blocks Angle Blocks These Angle Blocks were designed especially to strengthen machine frames and bases, or any construction requiring lateral stiffness of the profiles. Advantages include the elimination of angled profile cuts as well as a key-step which fits firmly into the profile T-slots, preventing rotation. 30, 35 and 45 Angle Blocks are standard. 30 Angle Block 30 79.01.0062 38,3 10 Threaded insert Ensat M8, 9S20K, K112030008 Ribbed Washer ø 8.4, Spring Steel Zn, K111010017 SHCS M8 x 20, DIN 912, 8.8 Zn, D0912820 35,8 10 Angle Block 35 79.01.0064 45 Angle Block 45 79.01.0066 10 52,1 10 45 SHCS M8 x 16, DIN 912, 8.8 Zn, D0912816 Ribbed Washer ø 8.4, Spring Steel Zn, K111010017 Nut 1 M8, Steel Zn, 34.01.0001 Angle Block 60 79.01.0068 192 mk Systems Profile Technology

Corner Blocks Series 50 A corner connection which provides a clean transition while increasing the aesthetic appeal of the construction. In combination with Profile mk 2000, Holder 5 must be installed. Profile mk 2003 requires an M8 thread. SHCS M8 x 20, DIN 912, 8.8 Zn, D0912820 Ribbed Washer ø 8.4, Spring Steel Zn, K111010017 Plug 5,, 79.00.0001 SHCS M6 x 12, DIN 912, 8.8 Zn, D0912612 Corner Block 4,, 79.01.0004 Corner Block 2,, 79.01.0002 SHCS M8 x 20, DIN 912, 8.8 Zn, D0912820 Ribbed Washer ø 8.4, Spring Steel Zn, K111010017 M6 MB Plug 5 79.00.0001 mk Systems Profile Technology 193

Corner Block 4 79.01.0004 connects for ex. 3 x Profile mk 2000 Corner Block 2 79.01.0002 connects for ex. 1 x Profile mk 2000 2 x Profile mk 2003 Corner Block 1 79.01.0001 connects 3 x Profile mk 2003 B51.03.003 with End Cap Corner Block 3 79.01.0003 connects for ex. 2 x Profile mk 2000 1 x Profile mk 2003 194 mk Systems Profile Technology

Corner Blocks Profile Wedges mk profile wedges aid in the construction of supporting structures of various heights. Depending on the profile selection, very long distances can be spanned, or high loads can be supported. Applications include mezzanines and trade show booths. Further information can be found on page 82 Profile Wedge 2 79.01.0052 Nut 1 M8, 34.01.0001 SHCS DIN 912, 8.8 Zn M8 x 30, D0912830 Profile Wedge 4 79.01.0054 SHCS DIN 912, 8.8 Zn M8 x 20, D0912820 M8 Ensat Threaded insert, 9S20K, K112030008 Nut 1 M12, 34.60.0301 SHCS DIN 912, 8.8 Zn M12 x 35, D09121235 Profile Wedge 5 79.01.0055 Profile Wedge 9 79.01.0059 mk Systems Profile Technology 195

Parallel Connectors Parallel Connector Series 25 25.50.3330 AlCuMgPb Parallel Connector Series B51.03.017 Series 50 B51.03.016 Series /50B51.03.018 Screw and Nut Steel, ZN 196 mk Systems Profile Technology

Profile Connectors Profile Connector 1 B51.03.021 Profile Connector 3 B51.03.023 Clamp, 79.00.0023 Clamp, 79.00.0025 Profile Connector 2 B51.03.022 Profile Connector 4 B51.03.024 Clamp, 79.00.0024 Clamp, 79.00.0026 mk Systems Profile Technology 197

Clamps Clamps Another method of fastening profiles is with the mk Clamps. Some clamps feature a key step, preventing rotation of the profile. Clamps without the key step allow profiles to be attached at various angles. Clamp 25/0 25.50.7000 Al F28 tumbled SHCS DIN 912, M8 x 20, 8.8 Zn, D0912820 Ribbed Washer ø 8.4 Zn, K111010017 Nut 1 M8, Steel Zn, 34.01.0001 Clamp 25/1 25.50.7001 Al F28 tumbled, Key width 6 mm Clamp 25/2 25.50.7002 Al F28 tumbled, Key width 6 mm Clamp /25 30.00.0048 Al F28 tumbled, Key width 10 mm 30 20 25 15 Clamp 5/30 30.00.0033 Al F28 tumbled 198 mk Systems Profile Technology

Clamp 6/30 30.00.0035 Al F28 tumbled, Key width 10 mm Clamp 1/ 30.00.0027 Al F28 tumbled Clamp 5/ 30.00.0034 Al F28 tumbled, Key width 10 mm Clamp 2/ 30.00.0029 Al F28 tumbled, Key width 10 mm 21,5 25 80 15 Clamp 6/ 30.00.0036 Al F28 tumbled, Key width 10 mm Clamp 2/50 30.00.0030 Al F28 tumbled, Key width 10 mm Clamp 7/80 30.00.0037 Al F28 tumbled Key width 10 mm 21,5 25 15 Clamp 3/70 30.00.0031 Al F28 tumbled, Key width 10 mm Clamp 1/30 30.00.0026 Al F28 tumbled Clamp 2/30 30.00.0028 Al F28 tumbled, Key width 10 mm Clamp 3/100 30.00.0032 Al F28 tumbled, Key width 10 mm mk Systems Profile Technology 199

Nuts Series 25 with T-Slot: 6 mm Series and 50 with T-Slot: 10 mm M5 Square Nut, Steel Zn M4 25.50.05 M5 25.50.0500 M6 25.50.0512 Nut 2/25, Steel Zn M5 25.50.0504 M6 25.50.0513 Nut 1, Steel Zn M8 34.01.0001 M6 34.02.0008 M5 34.12.0001 M4 34.08.0001 Nut 1, Stainless steel M8 34.01.0024 M6 34.02.0012 M5 34.12.0004 M4 34.08.0004 For T-Slot GUF-P Mini: 7 mm Profiles mk 2075, mk 2100 and mk 2150 Nut 2/25, Steel Zn M8 34.01.0002 M6 34.02.0010 M6 Nut 1, Steel Zn M6 34.02.0001 Nut 1, Stainless steel M6 34.02.0013 Nut 2/30, Steel Zn M5 34.12.0002 M6 Nut 2/25, Steel Zn M6 34.02.0002 M6 Nut 2/50, Steel Zn M6 34.02.0003 Nut 2/35, Steel Zn M8 34.01.0011 M6 Nut 3/25, Steel Zn M6 34.02.0004 Nut 2/, Steel Zn M8 34.01.0019 M6 Nut 2/75, Steel Zn M6 34.02.0005 Nut 2/50, Steel Zn M8 34.01.0003 200 mk Systems Profile Technology

Series 60 with T-Slot: 14 mm Nut 2/75, Steel Zn M8 34.01.0005 Nut 1, Steel Zn M8 34.60.0101 M10 34.60.0201 M12 34.60.0301 Nut 3/25, Steel Zn M8 34.01.0004 Nut 2/60, Steel Zn M10 34.60.0203 M12 34.60.0303 Nut 3/60, Steel Zn M10 34.60.0205 M12 34.60.0305 Nut 3/, Steel Zn M8 34.01.0022 mk Adapter Nut By using the adapter nut, keyed angles of series and 50 can be used with series 60 profiles. Adapter Nut 1, Al Keyed Angle Series 50 Nut 3/50, Steel Zn M8 34.01.0006 Nut 4/50, Steel Zn M8 34.01.0007 Adapter Nut 1, Al M6 34.60.2001 M8 34.60.2101 mk Systems Profile Technology 201

Nuts Nuts for last-minute Assembly The following components are designed to be inserted into the profiles after an assembly has been finished, or when the profile ends are inaccessible and the standard square nuts can no longer be slid into the T-slots. Flat-Head Inserts M5 Square Nut, Steel Zn M5 D05625 Nut S1 Steel Zn 34.09.0001 Slot Nut, Steel Zn M4 25.50.0541 M5 25.50.0501 ø23 10 T-Nut, Steel Zn M4 34.07.0004 M5 34.07.0003 M6 34.07.0002 M8 34.06.0002 Nut S2/ Steel Zn 34.09.0007 20 13 6 Slot Nut, Steel Zn M5 34.04.0002 M6 34.04.0001 M8 34.03.0001 Slot Nut, Stainless steel M6 34.04.0003 M8 34.03.0002 Nut S2/50 Steel Zn 34.09.0002 Slot Nut, Steel Zn M8 34.60.1101 M10 34.60.1201 M12 34.60.1301 Nut S2/100 Steel Zn 34.09.0006 10 12 13 Clip, plastic, Threaded insert Steel Zn M4 K111020006 M5 K111020007 M6 K111020008 M4 34.14.0006 M5 34.14.0007 M6 34.14.0008 202 mk Systems Profile Technology

Nut Placement and Holding For the profile series 25, and 50 mk offers components to hold nuts in position when installed into vertical T-slots. This is a significant aid when mounting components at such locations Nut Stopper red M8/Series mk 2555 PE Nut Stoppers For use with our standard square nuts and slot nuts, the nut stoppers offer the ultimate in convenience. They are simply pushed onto the thread of the nut, which is then located where desired in the profile T-slot. When the screw is tightened it simply displaces the nut stopper. These are single-use components and made of soft PE. Nut Stopper yellow M6/Series 50 mk 2556 PE Nut Stopper blue M8/Series 50 mk 2557 PE Spring Clips Spring clips hold mk square nuts in vertical T-slots. These clips must be placed prior to beam assembly, and are reusable. Spring Clips for Square Nut M5/M6 07.13.0003 Spring Steel Spring Clips for Nut 1/M8, M6, M5, M4 07.13.0002 Spring Steel Nut Stopper green M5/Series 25 mk 2553 PE Nut Stopper white M6/Series mk 2554 PE mk Systems Profile Technology 203

Electricity and Grounding If assemblies are electrified (i.e. lighting, electrical outlets, etc.), VDE 0100-410/413 requires that all conductive elements of the workplace must be connected via a common ground, so that the workplace remains safe in the case of an electrical short. As a rule, mk uses a grounding method in all it s standard workstation systems which is applied whether the workstation has electrical components or not. Connecting angles using our PE-Nuts, this grounding is accomplished without the use of additional wires. This means that in the case of later electric additions, the only the electric element itself must be connected with the workplace. Angle connection with PE-Nuts The nut is stamped to include protrusions which break through the anodized surface of the profile. This provides conductivity through the screw and thus ensures grounding of the connection. Grounding Nuts A defined grounding location of an mk workplace for attachment to a common ground. Groundconnection B02.99.151 Nut 1 M8 PE 34.01.0018 SHCS M8 x 16 DIN 912 D0912816, 8.8 Zn Angle Al Grounding Nuts Square Nut PE M5 25.50.0508 M6 25.50.0518 Nut 1 PE M8 34.01.0018 M6 34.02.0018 Nut 2/25 PE M5 25.50.0505 M5 204 mk Systems Profile Technology

Screws SHCS DIN 912, 8.8 Zn M4 x 6 D091246 M4 x 8 D091248 M4 x 10 D0912410 M5 x 8 D091258 M5 x 10 D0912510 M5 x 12 D0912512 M5 x 16 D0912516 M6 x 10 D0912610 M6 x 12 D0912612 M6 x 16 D0912616 M6 x 20 D0912620 M8 x 12 D0912812 M8 x 16 D0912816 M8 x 20 D0912820 M8 x 25 D0912825 M8 x 30 D0912830 M8 x 35 D0912835 M8 x D09128 M10 x 20 D09121020 M10 x 25 D09121025 M10 x 30 D09121030 M12 x 20 D09121220 M12 x 25 D09121225 M12 x 30 D09121230 SHCS DIN 912, Stainless steel M6 x 10 D0912610A2 M6 x 12 D0912612A2 M6 x 16 D0912616A2 M6 x 20 D0912620A2 M8 x 12 D0912812A2 M8 x 16 D0912816A2 M8 x 20 D0912820A2 M8 x 25 D0912825A2 M8 x 30 D0912830A2 M8 x 35 D0912835A2 SHCS DIN 6912, 8.8 Zn M6 x 12 D6912612 M6 x 16 D6912616 M6 x 20 D6912620 M8 x 12 D6912812 M8 x 16 D6912816 M8 x 20 D6912820 M8 x 25 D6912825 M8 x 30 D6912830 M10 x 20 D69121020 M10 x 25 D69121025 M10 x 30 D69121030 M12 x 20 D69121220 M12 x 25 D69121225 M12 x 30 D69121230 SHCS DIN 6912, Stainless steel M8 x 12 D6912812A2 M8 x 16 D6912816A2 M8 x 20 D6912820A2 FH-SHCS DIN 7991, 8.8 Zn M5 x 8 D799158 M5 x 10 D7991510 M5 x 12 D7991512 M6 x 10 D7991610 M6 x 12 D7991612 M6 x 16 D7991616 M8 x 12 D7991812 M8 x 16 D7991816 M8 x 20 D7991820 M8 x 25 D7991825 M8 x 30 D7991830 M10 x 20 D79911020 M10 x 25 D79911025 M10 x 30 D79911030 M12 x 20 D79911220 M12 x 25 D79911225 M12 x 30 D79911230 FH-SHCS DIN 7991, Stainless steel M6 x 10 D7991610A2 M6 x 12 D7991612A2 M6 x 16 D7991616A2 M6 x 20 D7991620A2 M8 x 12 D7991812A2 M8 x 16 D7991816A2 M8 x 20 D7991820A2 M8 x 25 D7991825A2 M8 x 30 D7991830A2 mk Systems Profile Technology 205

Screws and Square Nuts Hex Head Screw DIN 933, 8.8 Zn M4 x 6 D093346 M4 x 8 D093348 M4 x 10 D0933410 M5 x 8 D093358 M5 x 10 D0933510 M5 x 12 D0933512 M5 x 16 D0933516 M6 x 10 D0933610 M6 x 12 D0933612 M6 x 16 D0933616 M6 x 20 D0933620 M8 x 12 D0933812 M8 x 16 D0933816 M8 x 20 D0933820 M8 x 25 D0933825 M8 x 30 D0933830 M8 x 35 D0933835 M8 x D09338 M10 x 20 D09331020 M10 x 25 D09331025 M10 x 30 D09331030 M12 x 20 D09331220 M12 x 25 D09331225 M12 x 30 D09331230 Hex Head Screw DIN 933, Stainless steel M6 x 10 D0933610A2 M6 x 12 D0933612A2 M6 x 16 D0933616A2 M6 x 20 D0933620A2 M8 x 12 D0933812A2 M8 x 16 D0933816A2 M8 x 20 D0933820A2 M8 x 25 D0933825A2 M8 x 30 D0933830A2 Flanged Button-Head Screw, 10.9 Zn M6 x 10 K112010011 M6 x 12 K112010012 M6 x 16 K112010013 M6 x 20 K112010014 M8 x 12 K112010002 M8 x 16 K112010003 M8 x 20 K112010004 M8 x 25 K112010005 M8 x 30 K112010006 Set Screw DIN 914, 8.8 Zn M4 x 6 D091446 M4 x 8 D091448 M4 x 10 D0914410 M5 x 6 D091456 M5 x 8 D091458 M5 x 10 D0914510 M6 x 6 D091466 M6 x 8 D091468 M6 x 10 D0914610 M8 x 10 D0914810 M8 x 12 D0914812 M8 x 16 D0914816 M8 x 20 D0914820 Set Screw DIN 914, Stainless steel M6 x 6 D091466A2 M6 x 8 D091468A2 M6 x 10 D0914610A2 M8 x 10 D0914810A2 M8 x 16 D0914816A2 Hex Nut DIN 934, 8 Zn M5 D09345 M6 D09346 M8 D09348 M10 D093410 M12 D093412 Hex Nut DIN 934, Stainless steel M5 D09345A2 M6 D09346A2 M8 D09348A2 206 mk Systems Profile Technology

Washers Rib Washer, Steel Zn ø 4.3 ø 5.3 ø 6.4 ø 8.4 ø 10.5 ø12 K111010014 K111010015 K111010016 K111010017 K111010018 K111010019 Rib Washer, Stainless steel 1.4301 ø 4.3 K111010020 ø 5.3 K111010021 ø 6.4 K111010022 ø 8.4 K111010023 ø 10.5 K111010024 ø12 K111010025 Washer 3, Steel Zn, DIN-Countersink 90 ø 20 63.01.0008 ø 25 63.01.0009 ø 30 63.01.0010 Washer 4, Steel Zn, DIN-Countersink 90 ø 20 63.01.0011 ø 25 63.01.0012 ø 30 63.01.0005 Washer 5, Steel Zn, DIN-Countersink 90 ø 45 63.01.0006 Spring Washer, Steel Zn ø 8.4 Stainless steel ø 8.4 D67968 D67968.4A2 Washer 6, Stainless steel 1.4301 ø 30 63.00.0016 Washer 1, Steel Zn, DIN-Countersink 90 ø 20 63.00.0002 ø 25 63.00.0003 ø 30 63.00.0004 Washer 2, Steel Zn, DIN-Countersink 90 ø 20 63.00.0005 ø 25 63.00.0006 ø 30 63.00.0007 mk Systems Profile Technology 207

mk Accessory Components Overview Accessory Components 210 Floor Mounting Floor Mounting Plates 212 Base Plates 215 Base Consoles 217 Pedestal Bases 218 Cast Bases 222 Leveling Pads and Components 223 Handles and Knobs Handwheels 230 Handles 231 Adjustable Handles 232 Grips and Knobs 233 Door Components External Locks 234 Internal Locks 235 Hinges 236 Hinges for Panels 2 Ball Latches 241 Closure and Seal Strips 242 Paneling and Accessories 244 208 mk Systems Profile Technology

mk Accessory Components Rollers Mini-Rollers 246 Carriage Rollers 247 Guide Rollers 248 Furniture Casters 249 Fixed and Swivel Casters 250 Pneumatic Components 252 Electric Components Wireways 256 Sensor Brackets 260 End Caps 261 Wear Strips 265 Hoists 273 Swivel Joints 275 Ball Bases and Clamps 280 Ball Joints 286 Glides and Bushings 288 Bumpers 289 Tools 290 mk Systems Profile Technology 209

Overview Accessory Components Floor Mounting Page 212 Handles Page 230 and Knobs Door Page 234 Components Closure and Page 242 Seal Strips Paneling Page 244 and Accessories Rollers Page 246 Pneumatic Page 252 Components Electric Page 256 Components End Caps Page 261 210 mk Systems Profile Technology

Wear Strips Page 265 Hoists Page 273 Swivel Joints Page 275 Ball Bases Page 280 Ball Joints Page 286 Glides and Page 288 Bushings Bumpers Page 289 Tools Page 290 mk Systems Profile Technology 211

Floor Mounting Floor Mounting Plates Floor mounting plates can be used to anchor equipment such as stands, guards, workbenches, frames, etc. firmly to the floor. Plate /17 50.03.0025 Series SHCS M8 x 20, DIN 912, 8.8 Zn, D0912820 Ribbed Washer ø 8.4, Spring Steel Zn, K111010017 Threaded Insert Ensat M8, 9S20K, K112030008 Plate /18 50.03.0026 Plate /19 50.03.0027 Plate /20 50.03.0028 212 mk Systems Profile Technology

Series 50 SHCS M8 x 20, DIN 912, 8.8 Zn, D0912820 Ribbed Washer ø 8.4, Spring Steel Zn, K111010017 Plate /21 50.03.0029 Plate /22 50.03.0030 Plate /23 50.03.0031 Plate /24 50.03.0032 Base Plate 1 50.03.0001 mk Systems Profile Technology 213

Base Plate 2 50.03.0002 Base Plate 6 50.03.0006 Base Plate 4 50.03.0003 Base Plate 7 50.03.0007 Base Plate 4a 50.03.0004 Base Plate 5 50.03.0005 Base Plate 8 50.03.0008 214 mk Systems Profile Technology

Floor Mounting Base Plates Floor mounting plates can be used to place equipment such as stands, guards, workbenches, frames, etc. directly onto the floor. They can also be used to attach profiles to each other. Base Plate /1 50.03.0009 Ribbed Washer ø 8.4, Spring Steel Zn, K111010017 Threaded Insert Ensat M8, 9S20K, K112030008 SHCS M8 x 20, DIN 912, 8.8 Zn, D0912820 Base Plate /2 50.03.0010 Base Plate /3 50.03.0011 Base Plate /4 50.03.0012 Base Plate /5 50.03.0013 mk Systems Profile Technology 215

Series 60 Ribbed Washer ø 8.4 Spring Steel Zn, K111010017 Threaded Insert Ensat M8 9S20K, K112030008 SHCS M8 x 20 DIN 912, 8.8 Zn, D0912820 Base Plate 60/1 50.03.6001 Base Plate 60/8 50.03.6008 Base Plate 60/2 50.03.6002 Base Plate 60/9 50.03.6009 216 mk Systems Profile Technology

Floor Mounting Base Consoles mk Floor Consoles ensure a stable base, or a secure attachment for frames to the shop floor, for example. Console 54 compensates for uneven flooring and has an adjustment range of +/- 18 mm. Console 54 B67.02.037 Weight 10 kg, Console Cast Iron, Pad Steel Console 55 31.00.0028 Weight 3 kg, Cast Aluminum mk Systems Profile Technology 217

Floor Mounting Pedestal Bases mk Pedestal Bases ensure a stable platform for such things as frames, stands or guards. The can be used with all our profile series and have a clean design. By reinforcing the bases at their corners with more material, it is possible to machine threads or counter-bores at these locations. The bases are stocked in black (similar to RAL 9005), although other colors are available on request. Order either the individual plate or a complete assembly with included hardware (Anchor HST and Leveling Screws). 20x45 ø9 70 50 30 ø14 30 50 70 ø9 M16 Drill pattern example Leveling Screw DIN 916, 8.8 Zn, M16 x 60, D09161660 Anchor HST, M10 x 120, K111030011 H 25 10x45 30 10 8 On request we will rework the bases to your specifications (see drill pattern example). Please notice the location of the reinforcements (shown using centerlines) when specifying rework, as drilling through these reinforcements will adversely affect load capacity. 218 mk Systems Profile Technology

The centerlines denote the location of a reinforcment which runs on the underside of the plate. 300 300 0 0 Pedestal Base 6 50.02.0074 H=50 mm, planed Pedestal Base 6 50.02.0088 H=52 mm, not planed Painted matte black, Weight 10.5 kg Pedestal Base 6 B46.07.274 with anchors and leveling screws 500 Pedestal Base 8 50.02.0076 Painted matte black, Weight 13.7 kg, H=50 mm Pedestal Base 8 B46.07.276 with anchors and leveling screws, H=50 mm 162 300 0 500 Pedestal Base 7 50.02.0075 H=50 mm, planed Pedestal Base 7 50.02.0089 H=52 mm, not planed Painted matte black, Weight 12.1 kg Pedestal Base 7 B46.07.275 with anchors and leveling screws Pedestal Base 9 50.02.0077 Painted matte black, Weight 28.6 kg, H=50 mm Pedestal Base 9 B46.07.277 with anchors and leveling screws, H=50 mm mk Systems Profile Technology 219

Floor Mounting Pedestal Bases mk Pedestal Bases ensure a stable platform for heavy machien frames, gantries and stands. The Bases are pre-drilled for attaching some of the basic system profiles and painted black (similar to RAL 9005). The undrilled bases merely show the drills and taps required for floor attachment or leveling. Reworking and painting bases to customer specifications is possible on request. Floor attachment: Anchor HST, M10 x 120, K111030011 Leveling Screw DIN 916, 8.8 Zn, M16 x, D091616 M16 220 mk Systems Profile Technology

Pedestal Base 4 50.02.0028 Pre-drilled for mk 2000, mk 2004, mk 2005, mk 2011 Pedestal Base 2 50.02.0026 Pre-drilled for mk 2004, mk 2005, mk 2011 Undrilled 50.02.0128 Cast Iron, Painted matte black, 6.8 kg Undrilled 50.02.0126 Cast Iron, Painted matte black, 11.5 kg Pedestal Base 1 50.02.0023 Pre-drilled for mk 2000, mk 2004, mk 2005 Undrilled 50.02.0123 Cast Iron, Painted matte black, 8 kg Pedestal Base 5 50.02.0029 Pre-drilled for 2 x mk 2004, mk 2005, mk 2011 Undrilled 50.02.0129 Cast Iron, Painted matte black, 16.6 kg mk Systems Profile Technology 221

Floor Mounting Cast Bases Applications for mk Cast Bases include, for example, securing stands or pillars to the floor, or to other profiles. Cast Base 3 ø 50 65.00.0003 Cast Aluminum, 1.45 kg Cast Base 1 65.00.0001 Cast Aluminum, 0.8 kg Cast Base 4 ø 60 65.00.0004 Cast Aluminum, 1. kg Cast Base 2 65.00.0002 Cast Aluminum, 0.9 kg Cast Base 5 65.00.0005 Cast Aluminum, 1.35 kg 222 mk Systems Profile Technology

Floor Mounting Leveling Pads and Components The mk Leveling Pads with ball spindles compensate for uneven floors and provide height adjustment. To use leveling pads, attach mk Pad Plates to the profiles with M8 socket head cap screws, except for those attached directly into the profile ends. M10 M10 Leveling Screw M10 K110060003 Adj. range 10 mm, Load Capacity 1000 N Plastic/Steel Leveling Screw M8 K110060004 Leveling Pad KC M12 B67.02.077 Spindle length 50 mm, Adj. range 15 mm Leveling Pad KC M12 B67.02.027 Spindle length 75 mm, Adj. range 45 mm Leveling Pad KC M16 B67.02.028 Spindle length 85 mm, Adj. range 50 mm Load Capacity 1000 N Plastic Pad, Spindle Steel Zn Leveling Pad KA M10 B67.02.057 Adj. range 25 mm, Load Capacity 750 N Plastic Pad Spindle Steel Zn L Leveling Pad KB12 B67.02.075 Spindle length 50 mm, Adj. range 15 mm Leveling Pad KB M12 B67.02.001 Spindle length 75 mm, Adj. range 45 mm M12 Leveling Pad M12 B67.02.076 Adj. range 22 mm, Load Capacity 1000 N Plastic Pad Spindle Steel Zn Leveling Pad KB M16 B67.02.002 Spindle length 85 mm, Adj. range 50 mm Load Capacity 1500 N Plastic Pad, glass-fiber reinforced, Spindle Steel Zn mk Systems Profile Technology 223

M16 Leveling Pad EB M16 B67.02.0 Adj. range 50 mm Load Capacity 25000 N Stainless Steel Pad Stainless Steel 1.4305, Spindle Steel Zn Leveling Pad GC M20 B67.02.030 Adj. range 80 mm Load Capacity 30000 N Cast Iron Pad, Spindle Steel Zn Leveling Pad GD M16 B67.02.005 Spindle length 85 mm, Adj. range 50 mm Leveling Pad GD M20 B67.02.006 Spindle length 120 mm, Adj. range 80 mm Load Capacity 25000 N Cast Iron Pad with Rubber Damping, Spindle Steel Zn Without Damping Leveling Pad GA M16 B67.02.003 Leveling Pad GA M20 B67.02.004 Leveling Pad GB M16 B67.02.032 Spindle length 85 mm, Adj. range 50 mm Leveling Pad GB M20 B67.02.031 Spindle length 120 mm, Adj. range 80 mm Load Capacity 30000 N Cast Iron Pad, Spindle Steel Zn Leveling Pad GE M20 B67.02.033 Spindle length 100 mm, Adj. range 60 mm Leveling Pad GE M20 B67.02.034 Spindle length 150 mm, Adj. range 100 mm Leveling Pad GE M24 B67.02.035 Spindle length 100 mm, Adj. range 60 mm Leveling Pad GE M24 B67.02.036 Spindle length 200 mm, Adj. range 1 mm Load Capacity 100000 N Cast Iron Pad, Spindle Steel Zn 224 mk Systems Profile Technology

Floor Mounting Leveling Pads and Components at Profile Ends 15 20 80 20 20 Pad Plate I M10 50.02.0041 Pad Plate I M16 50.02.0030 For Profile mk 20.02, mk 20.41, mk 20.52 Threaded Insert Heli-Coil M10, K112030110 Leveling Screw M10, K110060003 Leveling Screw M10, K110060003 Plug 7, 79.00.0004 15 20 20 80 20 20 80 Pad Plate J M12 50.02.0067 Pad Plate J M16 50.02.0032 Pad Plate J M20 50.02.0050 For Profile mk 20.03, mk 20.45 Adj. range +/- 10 60 20 30 30 60 20 15 80 20 Threaded Insert Ensat M8, 9S20K, K112030008 Ribbed Washer ø 8.4, Spring Steel Zn, K111010017 SHCS M8 x 20, DIN 912, 8.8 Zn, D0912820 73 30 20 Pad Plate K M10 50.02.0043 Pad Plate K M16 50.02.00 For Profile mk 20.04 73 30 20 Pad Plate, 50.02.0032 Leveling Pad KB M16, B67.02.002 15 90 30 Pad Plate L M16 50.02.0044 For Profile mk 20.04 mk Systems Profile Technology 225

M10 M10 Pad Plate M10 50.05.0096 For Profile mk 20.38 Plug 7 79.00.0004 For Profile mk 2000 Pad Plate 60/4 M16 50.02.6004 Pad Plate 60/5 M20 50.02.6005 Pad Plate 60/6 M24 50.02.6006 For Profile mk 2060.02 Pad Plate A M10 50.09.0013 Pad Plate A M12 50.09.0044 Pad Plate A M16 50.09.0045 For Profile mk 2000 Pad Plate B M16 50.02.0003 Pad Plate B M20 50.02.0004 For Profile mk 2004 Pad Plate 60/8 M16 50.02.6008 Pad Plate 60/9 M20 50.02.6009 Pad Plate 60/10 M24 50.02.6010 For Profile mk 2060.05 Pad Plate C M16 50.02.0001 Pad Plate C M20 50.02.0002 For Profile mk 2005, mk 2011 Pad Plate 60/13 M20 50.02.6013 Pad Plate 60/14 M24 50.02.6014 For Profile mk 2060.22 226 mk Systems Profile Technology

15 Adj. range +/- 10 Pad Block, 67.00.0003 Threaded Insert Ensat M8, K112030008 SHCS M8 x 25, DIN 912, 8.8 Zn, D0912825 Leveling Screw M10, K110060003 Floor Mounting Leveling Pads and Components Pad Block M10 67.00.0010, without Leveling Screw For Profile mk 20.01, mk 20., mk 20.31, at profile ends 80 Pad Block M10 67.00.0003, SHCS M8 x 16, DIN 912, 8.8 Zn, D0912816 Nut 2/25 M8, 34.01.0002 20 without Leveling Screw For Profile mk 20.02, mk 20.41, mk 20.52 Pad Plate, 50.02.0010 Leveling Pad KB M12, B67.02.001 Pad Block M12 67.00.0007, without Leveling Screw For Profile mk 20.02, mk 20.41, mk 20.52 Nut 2/25 M8, 34.01.0002 SHCS M8 x 16, DIN 912, 8.8 Zn, D0912816 Pad Block M10 67.00.0002, without Leveling Screw For Profile mk 2000 Pad Angle, B67.02.009 Leveling Pad KC M12, B67.02.027 M12 Pad Angle M12 B67.02.009 Pad Angle M16 B67.02.010 Steel Zn mk Systems Profile Technology 227

Pad Plate D M12 50.02.0010 Pad Plate D M16 50.02.0011 Pad Plate G M16 50.02.0007 Pad Plate G M20 50.02.0008 Pad Plate E M16 50.02.0005 Pad Plate E M20 50.02.0006 Pad Plate H M12 50.02.0058 M12 Pad Plate F M16 50.02.0018 M16 228 mk Systems Profile Technology

Floor Mounting Leveling Pads and Components Support Bracket Support Bracket 2 26.00.0012 Steel Zn Support Bracket 1 26.00.0006 Steel Zn Support Bracket 60/1 26.00.0060 Steel Zn mk Systems Profile Technology 229

Handles and Knobs Handwheels For attachment to spindles, for example, as shown on the linear positioning module. Handwheel K110020030 Duroplast Fs 31, black Handwheel K110020029 Duroplast Fs 31, black Handwheel K110020031 Duroplast Fs 31, black 230 mk Systems Profile Technology

Handles and Knobs Handles The variety of handles are suitable for carrying, opening and closing, pushing of frames, doors, enclosures, windows, etc. Please order screws and nuts separately. Handle K110000020 PA-GF L = 152 mm B = 28 mm H = 60 mm L Handle K110000021 PA-GF L = 122 mm B = 27 mm H = 52 mm B B H 20 L Handle K110000009 PP-GF L = 117 mm B = 26 mm H = 41 mm Handle K110000010 PP-GF L = 179 mm B = 28 mm H = 50 mm H Handle K110000011 PA-GF, Al 20 L L = 200 mm Handle K110000012 PA-GF, Al L = 300 mm 26 55 Handle K110000013 PA-GF, Al L = 0 mm mk Systems Profile Technology 231

Handles and Knobs Adjustable Handles Adjustable Handle Cast Zinc A Stem Ident-Nr. 65 M6 x 15 K110030050 65 M6 x 20 K110030051 65 M6 x 25 K110030052 65 M8 x 15 K110030055 65 M8 x 20 K110030056 65 M8 x 25 K110030057 80 M10 x 20 K110030190 80 M10 x 25 K110030191 80 M10 x 30 K110030192 Adjustable Handle Plastic Adjustable Handle, Plastic K110030204 Nut 1 M8, Steel Zn, 34.01.0001 A Stem Ident-Nr. 65 M6 x 15 K110030200 65 M6 x 20 K110030201 65 M6 x 25 K110030202 65 M8 x 15 K110030204 65 M8 x 20 K110030205 65 M8 x 25 K110030206 80 M10 x 20 K110030207 232 mk Systems Profile Technology

Handles and Knobs Star Grips Handles and Knobs Palm Grips M8 Star Grip D6336K08 Thermoplast, black M8 Palm Grip K1100104 Thermoplast, black M8 Palm Grip K1100105 Thermoplast, black M10 Star Grip D6336K1050 Thermoplast, black M10 Palm Grip K1100107 Thermoplast, black M8 Star Grip K1100110 Thermoplast, black Handles and Knobs Knobs M10 Ball Knob D319E10 Duroplast Fs 31, M8 Star Grip K1100055 Thermoplast, black M8 black Ball Knob D319C830 Duroplast Fs 31, black M6 Ball Knob D319C625 Duroplast Fs 31, black mk Systems Profile Technology 233

Door Components External Locks Mounted to the door profile T-slot, the gap between the door and frame must be 24 mm. They are suitable for both swinging and sliding doors. 20 45 100 External Double-Bit Lock DIN-Right B68.02.017 DIN-Left B68.02.018 Swinging Door DIN-Right External Cylinder Lock DIN-Right B68.02.019 Swinging Door DIN-left DIN-Left B68.02.020 Sliding doors require special catch. Please inquire. Catch (complete w. set screw) B68.02.007 End Cap, mk 2507, PPN 6 M8 10 Catch 76.03.0004 Steel Zn 16 45 Set Screw M8 x 10 D0913810 34 34 ø 16 ø 16 Insert for Double-Bit Lock K117050003 Cast Zinc Insert for Cylinder Lock K117050001 Cast Zinc Spacer Plate 14.05.0010, Al Profile mk 20.31, L=100 mm 5431BN0100, Al Ribbed Washer ø 6.4 K111010016, Steel Zn SHCS M6 x 45 DIN 912 D0912645, 8.8 Zn M6 Keeper mk 2534 PA GF 30% black 234 mk Systems Profile Technology

...* Profile length in mm Door Components Internal Locks Installed within door frame profile. The gap between the door and frame must be 5 mm. Cylinder Lock complete as shown B68.02.051 L = 42 mm Cylinder Lock complete as shown B68.02.052 L = 52 mm L Profile Cylinder K117055000 L = 42 mm Profile Cylinder K117055001 L = 52 mm Keeper mk 2533 PA GF 30% black Profile Rework for Profile mk 20.01 51BC....* Please advise overall length and L1 dimension mk Systems Profile Technology 235

Door Components Hinges The variety of standard hinge arms allow combinations between the various profile series. A frame constructed using series 50 profiles, for example, can include a door built using series 25 profiles. All components, such as the hinge arms for example, can be ordered separately. Combination Hinge 25-1/25-1 Mounting Example A Hinge 25-1/25-1 B46.01.012 complete Mounting Example B Combination Hinge 25-1/-1 Hinge 25-1/-1 B46.01.013 complete End Cap PE, mk 2558 Grooved Pin DIN 1472-8 x 36 - St, D1472836 Spring Washer K111010001 236 mk Systems Profile Technology

Combination Hinge -1/-1 and -1/-7/-1 Combination Hinge 50-1/50-1 and 50-2/50-2 Hinge -1/-1 B46.01.010 complete Hinge 50-1/50-1 B46.01.001 complete Hinge -1/-7/-1 B46.01.030 complete Hinge 50-2/50-2 B46.01.002 complete Combination Hinge -1/50-1 Combination Hinge 50-1/60-1 Hinge -1/50-1 B46.01.011 complete Hinge 50-1/60-1 B46.01.064 complete mk Systems Profile Technology 237

Combination Hinge 60-1/60-1 and 60-1/60-7/60-1 Combination Hinge 25-1/50-1 Hinge 60-1/60-1 B46.01.058 complete Hinge 25-1/50-1 B46.01.014 complete Combination Hinge -1/60-1 Hinge 60-1/60-7/60-1 B46.01.059 complete Hinge -1/60-1 B46.01.063 complete 238 mk Systems Profile Technology

Door Components Hinges Hinge 25 B46.01.015 Hinge body GD Zn black, complete as shown Flat Head M5 x 10, D7991510 Nut M5, 25.50.0500 Plastic Hinge B46.01.033 Hinge body plastic, complete as shown mk Systems Profile Technology 239

Door Components Hinges for Panels Hinge 25-1/25-3 B46.01.044 complete Panel Nut M6, 41.00.0018 SHCS DIN 912, 8.8 Zn, M6 x 12, D0912612 Panel Nut M8, 41.00.0017 SHCS DIN 912, 8.8 Zn, M8 x 16, D0912816 Hinge -1/-3 B46.01.050 complete Panel Nut M8, 41.00.0017 SHCS DIN 912, 8.8 Zn, M8 x 16, D0912816 Hinge 50-1/-3 B46.01.055 complete 2 mk Systems Profile Technology

Door Components Ball Latches B68.02.101 for Door gap 5 mm complete B68.02.102 for Door gap 24 mm complete Nut 1, M6 34.02.0008, Steel Zn FH-SHCS M6 x 12, DIN 7991, D7991612, 8.8 Zn SHCS M6 x 12, DIN 912 D0912612, 8.8 Zn Ribbed Washer ø 6.4, K111010016, Steel Zn Ball Latches for Door gap 5 mm, B68.02.101 Door Stops Ball Latches for Door gap 24 mm, B68.02.102 Door Stop for Swing Doors (for 5 mm Door gap) 22.90.0035 Plastic PE Door Stop for Swing Doors (for 24 mm Door gap) 22.92.0035 Plastic PE mk Systems Profile Technology 241

Closure and Seal Strips Seal Strips firmly fix panels and/or plates which have been placed into the profile T-slots. These strips are designed for panel/plate thicknesses of 1.5-6 mm. Seal Strip mk 3011 with lip is used primarily for doors. Closure Strips prevent dirt and other contaminants from accumulating in the T-slots. The available colors can be used as accent stripes, or to identify a particular beam as containing air or wiring, for example. Seal Strip mk 3030 closes floor gaps of 5-25 mm. As shown below, the height of this strip can be adjusted by peeling off pieces to the desired height. Gap 5-25 Gap Gap 242 mk Systems Profile Technology

Closure Strips Closure and Seal Strips Closure Strip mk 3026 black EPDM, Stock length 100 m Seal Strip mk 3011 black EPDM, Stock length 200 m Closure Strip mk 3010 black PVC-P (soft), Stock length 100 m Seal Strips Closure Strip mk 3012 black mk 3014 blue mk 3015 yellow mk 3016 green mk 3017 red mk 3019 gray PVC-U (hard), Stock length 2 m for Gap 3.5-4.5 mm for Gap 4 mm Seal Strip mk 3027 black EPDM, Stock length 300 m Seal Strip mk 3033 black PVC-P, Stock length 200 m Closure and Seal Strips for Gap 5-6 mm Seal Strip mk 3020 black EPDM, Stock length 300 m Seal Strip mk 3025 black EPDM, Stock length 50 m Seal Strip mk 3032 black EPDM, Stock length 25 m for Profiles with closed T-slots for Gap 7-8.5 mm for Gap 10 mm Seal Strip mk 3021 black EPDM, Stock length 200 m Seal Strip mk 3023 black EPDM, Stock length 200 m Seal Strip mk 3030 black EPDM, Stock length m for Gap 12 mm Seal Strip mk 3024 black EPDM, Stock length 200 m mk Systems Profile Technology 243

Paneling and Accessories Paneling The paneling shown here can be used with all frames and doors shown in this catalog. When ordering, please advise all relevant frame dimensions for confirmation. Metal panels painted per your specifications. Paneling Material and Sizing Material * Max Size* Color Thickness Ident-Nr. Ident-Nr. Cut Acrylic 3050 x 2050 mm clear 4 mm K01D211004 50.15.6014 (120 x 80 ) 5 mm K01D211005 50.15.6000 6 mm K01D211006 50.15.6001 Polycarbonate 3050 x 2050 mm clear 4 mm K01B211004 50.15.6009 (120 x 80 ) 5 mm K01B211005 50.15.6002 6 mm K01B211006 50.15.6003 3050 x 2050 mm gray 4 mm K01B231004 50.15.6009 (120 x 80 ) 5 mm K01B231005 50.15.6002 6 mm K01B231006 50.15.6003 PETG 3050 x 2050 mm (120 x 80 )clear 6 mm K01P211006 50.15.6017 Fencing 3000 x 2000 mm Al x mm 4 mm K00315122. 24.00.0000 (118 x 78 ) St x mm 4 mm K00128222. 24.02.0000 Alucobond 2500 x 1250 mm silver anodized 4 mm K00316110 50.15.01 (98 x 49 ) 6 mm K0031611600 50.15.02 Steel painted 2500 x 1250 mm specify 1.5 mm K00316110 07.28.0000.0000 (98 x 49 ) 2 mm K0031611600 07.31.0000.0000 Stainless steel 2500 x 1250 mm 1.5 mm K00316110 07.29.0000.0000 (98 x 49 ) 2 mm K0031611600 07.32.0000.0000 Aluminum 2500 x 1250 mm silver anodized 1.5 mm K00316110 07.30.0000.0000 (98 x 49 ) 2 mm K0031611600 07.33.0000.0000 Sizing * Note: Paneling selection may vary subject to local and international standards and availability. Please confirm this prior to releasing any specifications. Installed using: Width Height Installed using: Width Height Seal Strip LM + 20 mm LH + 20 mm Angle LM LH Panel Clamp LM - 31 mm LH - 31 mm Fencing w. Clamp Profile LM + 10 mm LH + 10 mm Panel Block LM LH 244 mk Systems Profile Technology

Paneling and Accessories Paneling with Panel Blocks Paneling 2-6 mm Hex Nut M8 DIN 934 D09348, 8.8 Zn Panel Block mk 2552 Flanged Button Head Screw M8 x 12 K112010002, 10.9 Zn Paneling and Accessories Paneling with Angles Panel clamps are used to mount 5-8 mm thick paneling onto assembled frames. For paneling attached directly to angles, panel blocks add additional support for lengths of over 600 mm. Nut 1 M8 34.01.0001, Steel Zn Flanged Button Head M8 x 16 K112010003, 10.9 Zn Cover 07.01.0005, Steel Zn black Angle with M8 thread Steel (1.5-2 mm) Ribbed Washer ø 8.4 K111010017, Steel Zn SHCS M8 x 16 DIN 912 D0912816, 8.8 Zn Paneling and Accessories Paneling with Panel Clamps Nut M8 DIN 934 D09348, 8.8 Zn Panel Block mk 2552 Flanged Button Head Screw M8 x 12 K112010002, 10.9 Zn Paneling (5-8 mm) Panel Clamp B34.01.001, PA6 30% GFK Panel Clamp B34.01.001 Panel Clamp 50 B34.01.002 Panel Block mk 2552 mk Systems Profile Technology 245

...* Wear Strip length in mm Rollers Mini-Rollers Mini-Rollers are used, for example, for pallet runouts at workstations, transfer stations, etc. They can be attached to profiles of Series and 50. Roller spacing depends on the product conveyed. Stock length of mk Wear Strips is 2000 mm. mk mini-roller K101120001 Steel Zn M8 Step Washer 63.00.0011 Steel Zn Wear Strip mk 10.05, 21.05....* mk mini-rollers B60.04.002 Complete as shown max. radial load 80N mk 10.05 21.05.2000 PE 1000 Nut 1 M8, 34.01.0001 mk 1008 22.08.2000 PE 1000 Step Washer, 63.00.0011 Wear Strip mk 1008, 22.08....* mk mini-roller, K101120001 246 mk Systems Profile Technology

Rollers Carriage Rollers Carriage Rollers can be used when frames or other equipment must travel in a linear direction, on either mk Profiles or tracks. M8 x16 Flange Roller A1 B60.00.003 Roll POM, Bushing Steel blackened max. radial load 200N M8 x16 Guide Roller A2 B60.02.002 Roll POM, Bushing Steel blackened max. radial load 200N M8 x16 Flat Roller A3 B60.01.003 Bushing Steel blackened, Roll POM max. radial load 200N Track B60.01.002 Bushing Steel blackened, Roll Steel max. radial load 1000N mk Systems Profile Technology 247

Rollers Guide Rollers Both roller types are used in combination with Series 50 profiles for simple guiding or transfer of workpieces. Flange Roller 1 B60.00.001 Roll Steel blackened, complete as shown max. radial load 500N Flange Roller 2 B60.00.002 Rolle POM, complete as shown max. radial load 200N Roller B60.01.001 Rolle Steel blackened, complete as shown max. radial load 1000N 248 mk Systems Profile Technology

Rollers Furniture Casters 54.5 Furniture Caster 1 K1060001 Load capacity 35 kg, Polypropylene 54.5 Furniture Caster 2 K1060002 Load capacity 35 kg, Polypropylene 10 13 Stem 1 K1060003 Steel Zn 37 ø 4 Stem 2 K1060004 Steel Zn, Attaches to wood surface mk Systems Profile Technology 249

Rollers Fixed and Swivel Casters Type A The zinc plated steel housing of mk Casters Type A can be attached to either the profile T-slots or the profile ends. The casters feature rubber wheels for quiet travel and bearings for smooth operation. Swivel casters are supplied standard with a totallock brake. Pad Plate I M10 50.02.0041 for Casters with thread M10 Pad Plate J M10 50.02.0042 for Casters with thread M10 Fixed Caster (B) Designation Wheel ø Tread Load Overall Pinion ø Ident-Nr. D width capacity height (mm) (mm) (mm) (kg) H (mm) Pad Plate R3 50.02.0093 for Casters with thread M10 BRA-VPA 50K 50 18 69 10.5 K1060010 BRA-VPA 75K 75 25 60 98 10.5 K106001041 BKRA-VPA 101K 100 32 90 133 12.5 K106001042 BKRA-VPA 125K 125 25 80 158 12.5 K106001043 Swivel Caster (FI) with Total-Lock LRA-VPA 50K FI 50 18 69 10.5 K1060001 LRA-VPA 75K FI 75 25 60 98 10.5 K106000141 LKRA-VPA 125K FI 125 25 80 158 12.5 K106000143 250 mk Systems Profile Technology

Rollers Fixed and Swivel Casters Type B The zinc plated steel housing of mk Casters Type B are attached to profiles using the plates shown. The casters feature bearings and nylon wheels for smooth operation, and have a high load capacity. Swivel casters are supplied standard with a totallock brake. Pad Plate R1 50.02.0091 Fixed Caster (B) Designation Wheel ø Tread Load Overall Pinion ø Ident-Nr. D width capacity height (mm) (mm) (mm) (kg) H (mm) Pad Plate R4 50.02.0094 BH-SPO 125K 125 500 170 1 x 110 K106001045 Swivel Caster (ST) with Total-Lock LH-SPO 125K ST 125 500 170 1 x 110 K106000145 mk Systems Profile Technology 251

Pneumatic Components Using pneumatic components, profiles mk 20.02 and mk 20.03 can be pressurized to provide compressed air at desired locations. This structural beam feature eliminates the need for additional plumbing in frames made using mk profiles. The pneumatic plates can be attached to the profile ends as well as their T-slots. The system is designed for a maximum pressure of 6 bar. Further information on request. Hose coupling Ribbed Washer ø 8.4, Spring Steel Zn, K111010017 O-Ring ø 12 x 2, K115010093 SHCS M8 x 25, DIN 6912, 8.8 Zn, D6912825 Nut 1 M8, 34.01.0001 Hose coupling Ribbed Washer ø 8.4, Spring Steel Zn, K111010017 SHCS M8 x 25, DIN 6912, 8.8 Zn, D6912825 Seal threaded insert Ensat M8, 9S20K, K112030008 When attaching the distributor plate to the T-slot, the connection is sealed using O-rings. A seal ensures leak-proof attachment of plates to the profile ends. 252 mk Systems Profile Technology

Pneumatic Components End Plates Pneumatic Components Supply Plates End Plate A 53.00.0100 End Plate B 53.00.0101 Supply Plate A G1/2" 53.00.0200 NPT1/2" 53.00.0210 NPT1/4" 53.00.0353 Supply Plate C G3/4" 53.00.0202 Pneumatic Components Distributor Plates Distributor Plate A G1/4" 53.00.0352 NPT1/4" 53.00.0353 Distributor Plate A18 G1/8" 53.00.0300 NPT1/8" 53.00.0330 Distributor Plate A14 G1/4" 53.00.0303 NPT1/4" 53.00.0333 Supply Plate B G1/2" 53.00.0201 NPT1/2" 53.00.0211 Distributor Plate A28 G1/8" 53.00.0301 NPT1/8" 53.00.0331 Distributor Plate A24 G1/4" 53.00.0304 NPT1/4" 53.00.0334 mk Systems Profile Technology 253

Distributor Plate B18 G1/8" 53.00.0306 NPT1/8" 53.00.0336 Distributor Plate B14 G1/4" 53.00.0318 NPT1/4" 53.00.0348 Distributor Plate C18 G1/8" 53.00.0310 NPT1/8" 53.00.03 Distributor Plate C14 G1/4" 53.00.0322 NPT1/4" 53.00.0362 Distributor Plate B28 G1/8" 53.00.0307 NPT1/8" 53.00.0337 Distributor Plate B24 G1/4" 53.00.0319 NPT1/4" 53.00.0349 Distributor Plate C28 G1/8" 53.00.0311 NPT1/8" 53.00.0341 Distributor Plate C24 G1/4" 53.00.0323 NPT1/4" 53.00.0363 Distributor Plate B38 G1/8" 53.00.0308 NPT1/8" 53.00.0338 Distributor Plate B34 G1/4" 53.00.0320 NPT1/4" 53.00.0350 Distributor Plate C38 G1/8" 53.00.0312 NPT1/8" 53.00.0342 Distributor Plate C34 G1/4" 53.00.0324 NPT1/4" 53.00.0364 Distributor Plate B48 G1/8" 53.00.0309 NPT1/8" 53.00.0339 Distributor Plate B44 G1/4" 53.00.0321 NPT1/4" 53.00.0351 Distributor Plate C48 G1/8" 53.00.0313 NPT1/8" 53.00.0343 Distributor Plate C44 G1/4" 53.00.0325 NPT1/4" 53.00.065 d 254 mk Systems Profile Technology

Distributor Plate D18 G1/8" 53.00.0314 NPT1/8" 53.00.0344 Distributor Plate D14 G1/4" 53.00.0326 NPT1/4" 53.00.0366 Drill Fixture Drill Fixture B46.03.007 with drill bushings Distributor Plate D28 G1/8" 53.00.0315 NPT1/8" 53.00.0345 Distributor Plate D24 G1/4" 53.00.0327 NPT1/4" 53.00.0367 Seals End Seal A 53.01.0005 Klingerid Distributor Plate D38 G1/8" 53.00.0316 NPT1/8" 53.00.0346 Distributor Plate D34 G1/4" 53.00.0328 NPT1/4" 53.00.0368 End Seal B 53.01.0006 Klingerid Distributor Plate D48 G1/8" 53.00.0317 NPT1/8" 53.00.0347 Distributor Plate D44 G1/4" 53.00.0329 NPT1/4" 53.00.0369 O-Ring ø 12 x 2 mm K115010093 NBR 872 mk Systems Profile Technology 255

Electric Components Wireways Wireways offer an alternative to the usual electronic and power supply covers. The are extremely functional and integrate neatly with mk profile systems. Further information can be found on page 256 5450CA0150 5450CB0150 Clip 01, 54.49.0030 Band, K115010217 Clip 02, 5449BA0030 Cable Tie, K399000002 5451CA0150 5451CB0150 5151CA0150 5151CB0150 256 mk Systems Profile Technology

5450BA0100 5450BB0200 5451BA0100 5451BF0200 5451BA0100 5450BF0200 5151BB0100 5151BE0200 5450BA0100 5451BB0200 5450BA0100 5450BC0200 5450BA0100 mk Systems Profile Technology 257

5450BA0100 5451BC0200 5450BA0100 To protect the cable, the edge of the supporting profile must be rounded. 5450CC0150 5451BA0100 5451BG0200 5451BA0100 5451CC0150 5151BB0100 5151BF0200 5151BB0100 5151CC0150 258 mk Systems Profile Technology

...* Profile length in mm Electric Components Clips and Corner Guard Clip 01 54.49.0030 mk 20.50 54.50....* 0.51 kg/m Clip 02 5449BA0030 mk 20.51 54.51....* 0.67 kg/m Clip 11 51.48.0030 80 Clip 12 5148BA0030 50 25 mk 2050 51.50....* 0.43 kg/m Clip mk 2550 PA 6 Corner Guard mk 2551 PPN 1060 mk 2051 51.51....* 0.56 kg/m 50 mk Systems Profile Technology 259

Electric Components Sensor Brackets Sensor Bracket C ø 9 16.00.0011 ø 13 16.00.0012 ø 19 16.00.0013 Steel Zn Sensor Bracket A ø 13 16.00.0000 ø 19 16.00.0001 R1/4'' 16.05.0011 Sensor Bracket D ø 9 16.00.0016 ø 13 16.00.0017 ø 19 16.00.0018 Steel Zn Sensor Bracket B ø 13 16.00.0006 ø 19 16.00.0007 Sensor Bracket E ø 9 16.00.0026 ø 13 16.00.0027 ø 19 16.00.0028 Steel Zn 260 mk Systems Profile Technology

End Caps End Caps of injection molded plastic (PPN 1060) cover the ends of the profiles and attach flush to the profile edges. The finish is matte black and add a pleasant aesthetic accent to frames. The end caps are simply pressed onto the profile. for Profile mk 2025.01 25.50.8000 Series 25 for Profile mk 2025.37 25.50.8004 Series Series 50 for Profile mk 2025.38 25.50.8005 Series 60 for Profile mk 2025.02 25.50.8001 mk Systems Profile Technology 261

for Profile mk 2025.20 25.50.8002 for Profile mk x 80 mm mk 2508 for Profile mk 2025.21 25.50.8003 for Profile mk 80 x 80 mm mk 2502 for Profile mk x mm mk 2507 for Profile mk 20.14 mk 2523 262 mk Systems Profile Technology

for Profile mk 20.15 mk 2524 for Profile mk 100 x 100 mm mk 2505 for Profile mk 50 x 50 mm mk 2500 for Profile mk 2001 mk 2501 for Profile mk 2004 mk 2504 for Profile mk 2030 mk 2503 mk Systems Profile Technology 263

Larger profiles can be covered by using a combination of end caps. As shown below, profile mk 20.05 can be capped using one each End Cap mk 2507 and mk 2508. for Profile mk 2060.01 mk 2561 for Profile mk 2060.02 mk 2562 for Profile mk 2060.05 mk 2563 264 mk Systems Profile Technology

Wear Strips Slide- and Wear Strips from mk ensure low friction for a variety of applications. The Wear Strips are made with PE - UHMW (PE - 1000) and are available exclusively in stock lengths of 2000 mm. Wear Strip mk 1025.71 25.71.2000 Wear Strip mk 1025.72 25.72.2000 Wear Strip mk 1025.73 25.73.2000 Wear Strip mk 1025.74 25.74.2000 mk Systems Profile Technology 265

Wear Strip mk 1000 22.00.2000 Wear Strip mk 1001 22.01.2000 Wear Strip mk 10.01 21.01.2000 Wear Strip mk 1017 22.17.2000 Wear Strip mk 10.02 21.02.2000 Wear Strip mk 1070 22.70.2000 Wear Strip mk 10.03 21.03.2000 Wear Strip mk 1071 22.71.2000 Wear Strip mk 10.04 21.04.2000 Wear Strip mk 1072 22.72.2000 Wear Strip mk 10.05 21.05.2000 Wear Strip mk 1008 22.08.2000 266 mk Systems Profile Technology

Wear Strips Wear Strips Conveyor Systems Plastic Belt Conveyors for Conveyor System SBF-P2000 for Conveyor System SBF-P2000 Wear Strip mk 1055 22.55.2000 Frame width 100 Wear Strip mk 1078 22.78.2000 Frame width 130 for Conveyor System SBF-P2000 Wear Strip mk 1075 22.75.2000 Frame width 205 for Conveyor System SBF-P2000 Wear Strip mk 1057 22.57.2000 Frame width 100 for Conveyor System SBF-P2000 Wear Strip mk 1077 22.77.2000 Frame width 130 for Conveyor System SBF-P2000 Wear Strip mk 1076 22.76.2000 Frame width 205 mk Systems Profile Technology 267

Wear Strips Wear Strips Conveyor Systems Dual-Lane Conveyors More Information see page 110 for Conveyor System KTF-P2010 Wear Strip mk 1037 22.37.2000 for Chain 1 / 2 " x 5 / 16 " single strand for Conveyor System DGF-P2100 Wear Strip mk 1016 22.16.2000 for Conveyor System KTF-P2010 Wear Strip mk 1038 22.38.2000 for Chain 1 / 2 " x 5 / 16 " single strand for Conveyor System ZRF-P2010 Wear Strip mk 1041 22.41.2000 for Conveyor System ZRF-P2010 Wear Strip mk 1042 22.42.2000 for Conveyor System KTF-P2010 Wear Strip mk 1033 22.33.2000 for Chain 1 / 2 " x 5 / 16 " dual strand Wear Strip mk 1034 22.34.2000 for Chain 1 / 2 " x 5 / 16 " dual strand 268 mk Systems Profile Technology

for Conveyor System SRF-P2010 Wear Strip mk 1048 22.48.2000 for Conveyor System DGF-P2001 Wear Strip mk 1005 22.05.2000 for Conveyor System SRF-P2010 Wear Strip mk 1047 22.47.2000 for Conveyor System RRF-P2001 Wear Strip mk 1052 22.52.2000 for Conveyor System SRF-P2012 Wear Strip mk 1051 22.51.2000 for Conveyor System Modul-con Wear Strip mk 1060 22.60.2000 for Chain 1 / 2 " x 5 / 16 " for Conveyor System SRF-P2012 Wear Strip mk 1050 22.50.2000 for Conveyor System Modul-con Wear Strip mk 1062 22.62.2000 for Chain 1" x 17 mm mk Systems Profile Technology 269

Wear Strips for Door Stops Wear Strips for Guides Wear Strip mk 1091 22.91.2000 Wear Strip mk 1009 22.09.2000 Wear Strips for Side Rails Profile mk 2239, 52.39....* Wear Strip mk 1090 22.90.2000 Profile mk 2238, 52.38....* Wear Strip mk 1030 22.30.2000 Wear Strip mk 1031 22.31.2000 270 mk Systems Profile Technology

Wear Strips Wear Strips for Guides and Slides Wear Strip mk 1026 22.26.2000 Wear Strip mk 1027 22.27.2000 Wear Strip mk 1021 22.21.2000 mk Systems Profile Technology 271

Hoists The Hoists can be attached to the ends of various profiles, as well as to profile T-slots. An excellent method of moving equipment, the maximum carrying capacity is directly related to the vertical load. Eye Bolt M16 DIN 580 D058016 M20 DIN 580 D058020 M16 C15 Zn 15 20 20 20 Pad Plate I M16 50.02.0030, Load capacity 600 kg 80 for Profile mk 20.02 62 ø 35 Rib Washer ø 8.4, Spring Steel Zn, K111010017 SHCS M8 x 20, DIN 912, 8.8 Zn, D0912820 20 20 20 20 Pad Plate J M16 50.02.0032, Load capacity 600 kg for Profile mk 20.03 15 80 80 27 Pad Plate K M16 50.02.00, Load capacity 415 kg threaded insert Ensat M8, 9S20K, K112030008 60 20 30 30 60 for Profile mk 20.04 20 15 80 20 mk Systems Profile Technology 273

Hoists M20 Pad Plate 1 M20 50.09.0037 Steel Zn, Load capacity 1200 kg for Profile mk 2000 Plate 4 M20 50.09.00 Steel Zn, Load capacity 1200 kg Pad Plate 3 M20 50.09.0038 Steel Zn, Load capacity 1200 kg for Profile mk 2004 Plate 5 M20 50.09.0041 Steel Zn, Load capacity 1200 kg Pad Plate 60/5 M20 50.02.6005 Load capacity 10000 N Pad Plate I M20 50.09.0039 Steel Zn, Load capacity 1200 kg for Profile mk 2005 Pad Plate 60/9 M20 50.02.6009 Load capacity 10000N 274 mk Systems Profile Technology

Swivel Joints Series 50 To attach profiles at various angles. The joints can be locked in position by tightening the shoulder bolt. Max. load 300 kg. Joint 1 20.00.0001 Joint 2 20.00.0002 Joint 3 20.00.0003 Joint 1, 20.00.0001 Nut, 41.00.0003 Shoulder Bolt, 05.06.0006 Joint 1, 20.00.0001 Shoulder Bolt 05.06.0006 Steel blackened Nut 41.00.0003 Steel blackened mk Systems Profile Technology 275

Swivel Joints Series To attach profiles at various angles. The joints can be locked in position by tightening the shoulder bolt. Max. load 300 kg. Joint 10 20.00.0010 Hex Nut M8, D09348 Joint 11 20.00.0011 Joint 10, 20.00.0010 Profile mk 20.01 Ribbed Washer ø 8.4, Spring Steel Zn, K111010017 SHCS M8 x 20, DIN 912, 8.8 Zn, D0912820 Joint 12 20.00.0012 Joint 10, 20.00.0010 Spacer, 14.04.0019 SHCS M8 x 35, DIN 912, 8.8 Zn, D0912835 Spacer for Joint 14.04.0019 AlCuMgPb 3.1645 276 mk Systems Profile Technology

Joint B21 B46.01.221 complete, as shown Joint B24 B46.01.224 complete, as shown Joint B22 B46.01.222 complete, as shown Joint B25 B46.01.225 complete, as shown Joint B23 B46.01.223 complete, as shown Joint B26 B46.01.226 complete, as shown mk Systems Profile Technology 277

Swivel Joints Series When tightened, the Swivel Joints with glide bushings remain movable. Max. load 300 kg. Swivel Joint 13 20.00.0013 Spacer, 63.01.0005 Swivel Joint 13, 20.00.0013 Profile mk 20.01 Ribbed Washer ø 8.4, Spring Steel Zn, K111010017 SHCS M8 x 20, DIN 912, 8.8 Zn, D0912820 Swivel Joint 14 20.00.0014 Swivel Joint 13, 20.00.0013 Glide Bushing, K101150078 Bushing, 05.02.0032 FH-SHCS M8 x 16, DIN 7991, 8.8 Zn, D7991816 Swivel Joint 15 20.00.0015 278 mk Systems Profile Technology

Swivel Joint B41 B46.01.241, with Glide Bushing Swivel Joint B01 B46.01.201 Swivel Joint B42 B46.01.242, with Glide Bushing Swivel Joint B02 B46.01.202 Swivel Joint B03 B46.01.203 Swivel Joint B43 B46.01.243, with Glide Bushing Swivel Joint B04 B46.01.204 Bushing for Swivel Joint 05.02.0032 Stainless Steel Swivel Joint B05 B46.01.205 Spacer 63.01.0005 St 50 K Swivel Joint B06 B46.01.206 mk Systems Profile Technology 279

Ball Bases and Clamps Ball Bases The Ball Bases are made of cast iron, and have a 60 range of motion. When at the desired angle, the position is maintained by tightening the included M8 x 25 SHCS. Spacer 14.04.0007 AlCuMGPb Ball 30.01.0007 Stainless Steel 1.4305 Base Plate, 50.01.0016 Clamp F1 30.00.0056 GGG Spacer, 14.04.0007 Clamp C1, 30.00.00 SHCS M8 x 25, DIN 912, 8.8 Zn, D0912825 Ball, 30.01.0007 Ribbed Washer ø 8.4, Spring Steel Zn, K111010017 SHCS M8 x, DIN 912, 8.8 Zn, D09128 Clamp C1 30.00.00 GGG 280 mk Systems Profile Technology

60 Base Plate 50.01.0014 Ball Base C1 B46.02.010 for mk 2000 Base Plate 50.01.0020 60 Base Plate 50.01.0015 Ball Base C2 B46.02.011 for mk 2004 Base Plate 50.01.0021 60 Base Plate 50.01.0016 Ball Base C3 B46.02.012 for mk 2005 and mk 2011 mk Systems Profile Technology 281

Ball Bases and Clamps Ball Bases Clamp B2, 30.00.0014 Ball, 30.01.0005 Rod M8, ø 12, 7000AA....* 55 Clamp Plate 1 30.04.0001 SHCS M8 x 20, DIN 912, 8.8 Zn, D0912820 Ball, 30.01.0004 Clamp B3 B46.02.008 2 x Clamp Plate 1, Screws, Ribbed Washers 282 mk Systems Profile Technology

...* Rod length in mm Clamp Plate 2 30.04.0002 Clamp B1 30.00.0014 Clamp B4 B46.02.009 2 x Clamp Plate 2, Screws, Nut, Ribbed Washers Clamp B2 30.00.0041 Ball 30.01.0004 Stainless Steel 1.4305 Ball 30.01.0005 Stainless Steel 1.4305 Clamp Plate 3 30.04.0003 Ball 30.01.0006 Stainless Steel 1.4305 Rod M8, ø 12 7000AA...* Stainless Steel 1.4305, Thread M8 one end Stock lengths 50, 75, 100, 150 and 200 mm Clamp E3 B46.02.023 2 x Clamp Plate 3, Screws, Ribbed Washers Rod M8, ø 16 7000AE...* Stainless Steel 1.4305, Thread M8 one end Stock lengths 50, 75, 100, 150 and 200 mm mk Systems Profile Technology 283

...* length in mm Ball Bases and Clamps Swivel Clamps mk Swivel Clamps are used heavily in the area of material handling side guides/rails. They allow guide rods to be positioned at various angles and heights. Clamp Stainless Steel, 30.00.0023 Clamp Plastic, mk 2522 SHCS M8 x 20, DIN 912, 8.8 Zn, D0912820 Rod M8 ø 12, 7000AA...* Clamp Stainless Steel, 30.00.0023 Clamp Plastic, mk 2522 Washer, 63.00.0016 Rod ø 10, 7000AB...* 284 mk Systems Profile Technology

...* length in mm Clamp mk 2522 PA6GF 30%, Fiber-reinforced Clamp complete B46.02.004 Stainless Steel 1.4305 M8 Clamp 2 30.00.0002 Clamp 30.00.0024 Stainless Steel 1.4305 Clamp 30.00.0023 Stainless Steel 1.4305 Clamp 30.00.0001, for T-slot 10 mm and Rod ø 12 mm Washer ø 30 63.00.0016 Stainless Steel 1.4305 Rod M8, ø 12 7000AA...* Stainless Steel 1.4305, Thread M8 one end Stock lengths 50, 75, 100, 150 and 200 mm Clamp complete B46.02.005 PA6GF 30%, Fiber-reinforced Rod ø 10 7000AB...* Stainless Steel 1.4305, chamfered Stock lengths 50, 75, 100, 150 and 200 mm mk Systems Profile Technology 285

Ball Joints These accessory components for rails are typically used in combination with profiles mk 20.01 and mk 20.16. They are aluminum, and feature a tumbled finish. Please note that they are not designed for exterior use. Swivel /H1 B46.01.022 complete as shown Swivel /H5 B46.01.026 Ensat threaded insert M8, 9520K, K112030008 SHCS DIN 912, 8.8 Zn, M8 x 60, D0912860 SHCS DIN 912, 8.8 Zn, M8 x 20, D0912820 Swivel /H2 B46.01.023 complete as shown T-Connector 79.00.0011 SHCS DIN 912, 8.8 Zn, M8 x 16, D0912816 Nut 1 M8, 34.01.0001 SHCS DIN 912, 8.8 Zn, M8 x 20, D0912820 Swivel /H4 B46.01.025 complete as shown 286 mk Systems Profile Technology

Swivel /H5 B46.01.026 complete as shown Wall attachment for Profile mk 20.01 50.03.0033 AL Swivel /H3 B46.01.024 complete as shown Wall attachment for Profile mk 20.16 50.03.0034 AL End Cap for Profile mk 20.16 76.01.0002 AL T-Connector for Profile mk 20.16 79.00.0011 AL mk Systems Profile Technology 287

Accessory Components Glides and Bushings The following components are often used in material handling applications as stops or singulators, for example. Using just a few elements, guides for a variety of tooling can be made as well. These components are designed for use with profile mk 2000. Bushing ø 12 35.00.0007 D =12 mm Shaft ø 12 0100AF....* Shaft ø 16 0100AA....* St50K h6 Bushing ø 16 35.00.0006 D =16 mm, Delrin M8 Shaft ø 12 0100AE....* Shaft ø 16 0100AB....* hardened h6 Stock lengths 150, 200, 250, 300, 350 and 0 mm Bushing 35.00.0008 Delrin M8 Shaft 0101AA....* Steel C45 polished h9 Stock lengths 150, 200, 250, 300, 350 and 0 mm Lager for Linear Bearing B.03.002 Aluminum with Linear Bearing 16 /26 x 36 mm 288 mk Systems Profile Technology

Bumpers Elastomer, Shore 55 Bumper Type D D H Thread Ident-Nr. 20 12 M6 x 12 K113060004 20 12 M6 x 15 K113060001 30 28 M8 x 20 K113060002 50 21 M10 x 28 K113060003 Bumper Type D Hex Nut M6, D09346 Bumper Type K/D D H Thread Ident-Nr. 25 17 M6 x 18 K113060006 50 18 M10 x 28 K113060007 Bumper Type KP/D Nut 1 M8, 34.01.0001 Bumper Type KP/D D H Thread Ident-Nr. 30 36 M8 x 10 K113060012 30 36 M8 x 16 K113060013 30 36 M8 x 23 K113060011 mk Systems Profile Technology 289

Tools Taps and Threadformers Thread Type Order Number M 3 Blind Hole Tap K903060003 M 4 Blind Hole Tap K903060004 M 5 Blind Hole Tap K903060005 M 6 Blind Hole Tap K903060006 M 8 Threadformer K903070008 M 8 Blind Hole Tap K903060008 M 9 x 1 Blind Hole Tap K903060109 M 10 Blind Hole Tap K903060010 M 12 Blind Hole Tap K903060012 M 12 x 1,5 Blind Hole Tap K903060113 M 16 Blind Hole Tap K903060016 M 16 x 1,5 Blind Hole Tap K903060116 Thread Type Order Number M 2 Helicoil K903060202 M 2,5 Helicoil K903060201 M 3 Helicoil K903060203 M 4 Helicoil K903060204 M 5 Helicoil K903060205 M 6 Helicoil K903060206 M 8 Helicoil K903060208 M 10 Helicoil K903060210 M 12 Helicoil K903060212 Insert Tools for Ensat inserts Insert Tools for Helicoil inserts Thread Tool Length Type Order Number Thread Tool Length Type Order Number M3 58 H K902010004 M6 102 M K902010011 M3 82 M K902010005 M8 81 H K902010012 M4 65 H K902010006 M8 105 M K902010013 M4 83 M K902010007 M10 89 H K902010014 M5 69 H K902010008 M10 131 M K902010015 M5 101 M K902010009 M12 95 H K902010016 M6 74 H K902010010 M12 118 M K902010017 Type H=Hand operated, Type M=Machine operated Thread Type Order Number M3 H K902010203 M4 H K902010204 M5 H K902010205 M6 H K902010206 Type H=Hand operated Thread Type Order Number M8 H K902010208 M10 H K902010210 M12 H K902010212 Wrench Set The ball-end allows quick and easy installation of the screw. When tightening, the longer arm of the wrench provides a sufficient torque arm to set the fastener. The wrenches are made of Chrome-Vanadium Steel. Type Wrench Set 8-piece Order Number K902005050 290 mk Systems Profile Technology

Magnetic Holder for Nuts Used to grab or hold nuts in profile T-slots. Ideal for moving nuts into vertical positions. Features a chromeplated flexible brass tube and plastic handle. Type Magnetic Holder Order Number K901130001 Drill Fixtures for Tension Plugs These drill fixtures are used to drill holes in profiles for tension plugs. Made of hardened steel with detent. Drill Fixture D* A* Order Number Series 25 5,8 15 B46.03.003 Series und 50 10 15 B51.03.005 * Values in mm Drill Fixture for Pneumatics These drill fixtures are used to drill holes in profiles for pneumatic adapter plates. Made of hardened steel with drill bushings. Drill Fixture for pneumatic components Order Number B46.03.007 Drill Fixture for Flat Finish Profiles These drill fixtures are used to drill holes in profiles in Flat Finish profiles. Drill Fixture for Flat Finish profiles Order Number B51.03.020 Parting Tool for Flat Finish Profiles To open T-slots on Flat Finish profiles. Type Order Number Parting Tool B46.03.102 mk Systems Profile Technology 291

mk Assemblies Turntables 294 Carriage Wagons 296 Carriages 298 Linear Modules 300 mk Systems Profile Technology 293

Turntables mk Turntables are most often used in the area of manual material handling. Heavier loads can be positioned effortlessly for assembly or machining operations. The turntable consists of a solid cast aluminum base with an aluminum surface plate. The surface plate is supported on 6 roller bearings and rotates centric to the base on another roller bearing. mk Turntables are available with either a ø 0 mm round or 0 x 0 mm square surface plate. In addition, the Indexing and Fixed versions are available with 2, 4 or 6 stop locations. Special versions please inquire. The maximum load rating is 100 kg. Do not drill/tap in this area! Fixed Version Indexing Version Example of a Special Version 294 mk Systems Profile Technology

Turntable with Index B12.00.001 Turntable with Fixed Stops B12.00.002 not shown Turntable without Index B12.00.003 Ordering example for above drawing: Please indicate surface plate type (round or square) and number of Indexing, i.e. Fixed stops. Turntable B12.00.002 Fixed Stops 6 Surface Plate round mk Systems Profile Technology 295

Carriage Wagons mk Carriage Wagons are used where equipment or machines are moved into position on tracks. The mk Carriage Wagons are available in stock lengths of 0, 500 and 600mm. Other versions please inquire. Please indicate roller version and wagon length when ordering. More Information page 247 Version Radiallast/Rolle Flange Roller, Steel 1 1000N Flat Roller, POM 2 200N Guide Roller, Steel 3 1000N Guide Roller, POM 4 200N Guide and Flat Roller, POM 5 0N 1 2 3/4 5 Carriage Wagon mk 20.02 B90..001 Carriage Wagon mk 20.03 B90..002 L L 296 mk Systems Profile Technology

Carriage Wagon mk 2004 B90.00.002 Carriage Wagon mk 2000 B90.00.015 L L Carriage Wagon mk 2005 B90.00.003 L 100 Roller Unit B60.04.004 mk Systems Profile Technology 297

Carriages Series mk Carriages offer simple linear motion for a variety of applications. The rollers are made of high quality plastic which houses a sealed roller bearing. Exact alignment and travel are aided through the use of excentric bushings. Carriage B38.00.0 complete Base Plate Alu, Steel Cover, painted black, 4 Rollers Load capacity max. 0 N Carriage 80 B38.00.041 complete Base Plate Alu, Steel Cover, painted black, 4 Rollers Load capacity max. 0 N Roller Bearing 6004-2RS1 M8/16 deep M8/16 deep Roller B60.02.010 complete Roller Plastic, Bushing Steel, Roller Bearing 6004-2RS1 Stainless Steel Roller excentric B38.00.009 complete Roller Plastic, Bushing Steel, Roller Bearing 6004-2RS1 Stainless Steel 298 mk Systems Profile Technology

Carriages Series 50 Carriage 50 B38.00.002 complete Base Plate Alu, Steel Cover, painted black, 4 Rollers Load capacity max. 0 N Carriage 100 B38.00.001 complete Base Plate Alu, Steel Cover, painted black, 4 Rollers Load capacity max. 0 N M8/16 deep Roller B60.02.003 complete Roller Plastic, Bushing Steel, Roller Bearing 6004-2RS1, Stainless steel Roller Bearing 6004-2RS1 M8/16 deep Roller excentric B38.00.001 complete Roller Plastic, Bushing Steel, Roller Bearing 6004-2RS1, Stainless steel mk Systems Profile Technology 299

Linear Modules mk Linear Positioning Modules are designed to solve adjustment and positioning tasks. Typical applications include measurement and test equipment, as well as labeling and packaging machinery. The supporting beams of the two basic sizes offered are our structural aluminum profiles. These profiles are reworked and subsequently hardcoated. This ensures a low friction surface with excellent durability. The internal trapezoidal spindle is protected from contaminants by polyamide covers. Adapter plates as well as customer specific versions are possible on request. Linear Module with two support plates, opposing travel Two Linear Modules for positioning in two axes Two Linear Modules for parallel adjustability Linear Module with one support plate Two Linear Modules with common base plate 300 mk Systems Profile Technology