TSUBAKI LOW NOISE DRIVE CHAIN NEW
Low Noise Drive Chain SN Roller Chain Tsubakimoto introduces its original spring roller for use in roller chain. When Tsubaki s SN Roller Chain engages with the sprocket, the new spring roller absorbs the force of the impact. The lower impact force results in lower noise levels. Compared with Tsubaki s standard RS Roller Chain (pre-lubricated), noise levels of SN Roller Chain are 6~8 db lower. Standard RS Roller Chain Roller Low Noise Drive Chain Spring Roller (Moldability) Noise Noise abatement What the change to Low Noise offers RS is a registered trademark of the Tsubakimoto Chain Co. Reduction of noise generated by machines and equipment in the workplace helps improve the overall work environment. Belts were considered as a countermeasure to noise, however, there are many limitations in terms of application, strength and overall cost. Taking these factors into consideration Low Noise Chain is the prefect countermeasure. Can be used in applications where the strength of a roller chain is required without the accompanying noise. (Theatrical stage lifts and others) Features q Low noise Compared with Tsubaki s standard RS Roller Chain (pre-lubricated), noise levels of SN Roller Chain are 6~8 db lower. Noise level (Tsubaki comparison) Noise Level db (A) 85 80 75 70 65 60 50 RS50 (Std. Roller Chain) RS50SN (Low Noise Drive Chain) Test Conditions Chain tension: 3.2 kn (881 lbs) : Pre-lubricated only Measurement position: 0 mm (.81 in.) from the drive sprocket Test Chain RS50SN (Low Noise Drive Chain) RS50 (Std. Roller Chain) Speed Reducer with Motor 0 mm Drive Measurement Device 50 (4) 0 (3) Chain Speed m/min (ft/min) 0 (42) w Interchangeability Directly interchangeable with Standard Roller Chain Note: As there are limits to the drive power of SN Roller Chain, please check the drive power charts on pages 3~4 when making your selection.
Use Stage equipment Warehouse Printing Machine Noise Reduction Canning Machine Wrapping Machine Vertical Parking System Product Type and Dimensions R T Offset link L2 L1 h D H W T L P P The connecting link for RS80SN is a cottered pin type. Chain No. RSSN-1 RS50SN-1 RS60SN-1 RS80SN-1 Pitch P.70 (1/2).875 (5/8).05 (3/4). (1) Roller Diameter R 8.5 (0.3).8 (5).6 ().8 (1) Inner Link s Inner Width W 7.5 (3).53 (0.375).70 (0).88 (5) Thickness T 1.5 (0.05) 2.0 () 2.4 (0.04) 3.2 (6) Plate Height H.0 (2).0 (1).1 (0.7).1 (0.4) Height h.4 ().0 (2).6 (0.6).8 (0.8) Diameter D 3.7 (6) 5.0 (0) 5.6 (5) 7.4 (3) L1+L2.2 (0.7).3 (8) 27.6 (1.087).5 (1.38) Pin L1 8. (5).3 (6) 1 (6). (0) L2.5 (2).0 (2).75 (1). (8) Unit: mm (inch) L.0 (0.70).5 (0.886).2 (1.1) 36.0 (1.4) Chain No. RSSN-1 RS50SN-1 RS60SN-1 RS80SN-1 Selection Min. Tensile Strength kn {kgf} (lbs).7 {00} (380).4 {200} (6380).2 {} (0) 71.6 {70} (0) Avg. Tensile Strength kn {kgf} (lbs).1 {50} (420) 31.4 {30} (7060) 44.1 {00} () 78.5 {8000} (600) Operating Temperature Allowable Chain Speed Max. Allowable Tension kn {kgf} (lbs) 3.63 {370} (8) 6.37 {650} () 8.83 {00} (0).7 {00} (30) Approx. Mass kg/m (lbs/ft) () 1.04 (0.70) 1.53 (1.03) 2.66 (1.7) No. of Links/Unit 0 2 0 1 Delivery Made to Order * { } Reference Value Please select by referring to the Drive Power chart on the following page or based on Low Speed (When chain speed is less than 50 m/min (4 ft/min)). Please refer to the selection page of the Drive Chain catalog for more details. C ~ +60 C (+ F ~ +0 F) 0 m/min (656 ft/min) RS Standard can be used.
Low Noise Drive Power Chart MAXIMUM KILOWATT (HORSEPOWER) RATINGS CHART RSSN <Single Strand Chain Drive kw> 0.05 0.05 0.06 0.08 0.08 0.0 0. 0. 0. 0. 50 0 0 0 0 500 700 00 00 10 00 00 0. 0. 0. 0.33 0.41 0.56 0.33 0.36 0.41 0.4 0.52 0.65 0.71 0.81 1.04 1. 0.53 0.67 0.77 0.82 0.2 0.6 1. 1. 1. 1.52 1.3 0.81 0.8 1. 1. 1.34 1.43 1.52 1.62 1.71 1. 2.08 2.46 2.65 2.84 3. 3.61 4. 1.04 1. 1.3 2.06 2.33 2.46 2.86 3.00 3. 3.54 3.81 4.0 4.50 5. 5.1 1.84 2.34 2.84 3.02 3. 3.36 3.71 3.88 4.06 4. 4.58 4.4 5.2 5.83 1.84 2. 2.65 2.86 3.48 3.6 3.0 4. 4. 4.53 4.74 4.6 5. 5.60 6.04 1. 1.44 2.06 2.2 2.52 2.76 3.01 3. 3.52 3.7 4.06 0.73 0.85 1. 1.27 0.73 0.6 1.08 1.34 0.73 0.82 RS50SN <Single Strand Chain Drive kw> 0. 0. 0. 0.37 0.37 0.4 0.6 0.78 1. 0.53 0.6 0.85 0.1 0.6 1. 1. 1. 1.6 1.86 2. 2.44 1.0 1. 1.3 1.5 1.6 1.7 2. 2. 2.51 2.3 3. 4.00 4.54 50 0 0 0 0 500 700 00 00 10 2. 2. 2.78 2.8 3. 3.34 3.72 3.1 4. 4. 4.4 4.6 5.47 5.87 6.46 7.47 8.48 2. 2.3 3. 4.00 4.27 4.54 5.0 5.36 5.64 5.2 6. 6.47 6.75 7. 7.88 8..31.80 2.78 3. 3.80 4. 4.48 4.83 5. 5.53 5.88 6. 6.5 6.5 7.31 7.66 8.03 8.3 8.75.48. 2. 3. 4.0 4.53 4. 5.47 5.6 6.46 6.8 7.51 8.05 8.60..75 1.27 1.72 2. 2.74 3.01 3. 1. 1.34 3 0.08 0.0 0.0 0.27 0.67 50 0 0 0 0 500 700 00 00 10 00 00 0.68 0.88 0.2 0.7 1.05 1.74 0.52 0.70 0.83 0.5 1.0 1.3 0.71 0.78 0.2 1. 1.43 1.66 1.81 2. 2.4 2.87 0.52 0.71 0.83 0.7 1.03 1. 1. 1. 1.55 1.62 1.77 1.0 2.5 0.7 1.0 1.31 1.43 1.55 1.68 1.2 2.2 2.7 2.1 3.04 3. 3.55 3.81 4. 4.84 5.50 1.5 1.86 2. 2. 2.68 2.5 3.08 3. 3.36 3.65 3.3 4. 4.64 5.36 6.08 1.3 1.55 1.0 2.06 2.76 2.5 3. 3. 3.47 3.83 4.02 4. 4.38 4.74 5. 5.48 6.03 6.7 7.2 2.8 3. 3.47 4. 4.48 4. 5. 5.51 5.76 6.02 6.2 6.81 7.87 8.66.0.4 1.81 2.02 2.68 2.1 3. 3. 3.58 3.81 4.05 4. 4.50 4.7 5. 5.44 5.67 6. 6.62 7.0 7.82 2.88 3. 3.58 3.3 4. 4.64 5.00 5.36 5.72 6.08 6. 6.82 7. 7.56 7.3 8. 8.67.05.81.6.3.5.5 3.00 3. 3.55 3.83 4. 4.38 4.66 4.5 5. 5.51 5.7 6.07 6. 6.65 6.3 7.51 8. 4. 4.64 5.0 5.55 6.00 6.47 6.4 7.41 7.88 8.36 8.83..80.3.8.2.7.7 1.68 1.3 2.76 3. 3.38 3.70 4.03 4.37 4.72 5.44 2.83 3.31 4.34 4.1 5.48 6.07 6.6 7. 8.66.36.1.8.5.3.1 0.8 1. 1.70 1.0 2. 2. 1.70 2.63 2.6 3.31 3.67 4.03 4.42 0.83 0.8 1. 1.62 0.8 1. 1. 1.37 2.02 0.68 50 0 0 0 0 500 700 00 00 10 1. 0.88
Low Noise Drive Power Chart MAXIMUM KILOWATT (HORSEPOWER) RATINGS CHART RS60SN <Single Strand Chain Drive kw> 50 0 0 0 0 0 500 600 700 800 00 00 10 0. 0. 0.33 0.4 0.56 0.61 0.65 0.70 0.77 0.8 0.41 0. 0.65 0.70 0.81 0.1 0.6 1. 1. 1. 1.38 1.60 1.76 0.85 0.4 1.03 1.31 1.41 1.60 1.70 1.7 1. 2.08 2. 2. 2.38 2.58 2.78 2.8 3. 3.7 4. 1.41 1.75 1.3 2. 2. 2. 2.63 2.8 3. 3.34 3.71 3.8 4.07 4. 4.44 5. 5.56 6. 7.07 8.03 2. 2.77 3.03 3. 3.7 4.04 4. 4.56 4.82 5.34 5.60 5.87 6. 6. 6.3 7.46 8.00 8.82..60 2.63 2.5 3.5 3.2 4. 4.57 4.0 5. 5.57 5.0 6. 6.58 6.2 7. 7.60 7.4 8.2 8.8.67....00 3.7 4. 4.71 5. 5.65 6. 6.5 7.06 7.54 8.02 8.51 8..48.6.50.0..0.0.0.0 3.41 4.60 5. 5.1 6.61 8.07 8.84.63....0.50..80.50 2.44 3.2 3.75 4. 5. 5.78 6.33 6.8 7.47 8.07 3. 3.60 4.3 1.47 1.72 1. 2. 2.55 1. 1.41 1.63 2.0 RS80SN <Single Strand Chain Drive kw> 0. 0.4 0.6 0.7 0.8 0.4 1.04 1. 1. 1. 1.36 1. 2. 0.1 1. 1.6 1.2 2. 2.38 2.62 2.74 3.0 3.33 3.57 3.4 4.55 5. 1.6 1.0 2. 2.52 2.4 3. 3.37 3.58 3.80 4.01 4. 4. 4.67 4.8 5. 5.33 5.77 6. 6.67 7.34 8.48.63 3. 3.54 3.3 4.31 4.70 5.0 5.4 5.88 6. 6.68 7.08 7.4 7.8 8. 8.71..53.4.80.60. 0.80.00 4.55 5. 5.65 6. 6.77 7.34 7.0 8.48.05.63..80. 1.50. 0..50.70.0.70.80.0 5.0 6.61 8.05 8.77.51..00.70.50..00.70.50..00.80.50..60..60 6.60 7.73 8.2..50.80..60.0.00.00.....50.60.70 4.2 5.02 5.7 6.60 7.44 8...... 3.07 3.5 4. 4.72 5.33 5.5 6.60 2.33 3. 3.5 4.05 1. 1.36 4 50 0 0 0 0 0 500 600 700 800 00 00 10 0.27 0.56 0.68 0.82 0.4 1.03 1. 50 0 0 0 0 0 500 600 700 800 1.52 0.7 0.2 1. 1. 1.3 1.47 1.61 1.68 1.82 2. 2. 3.03 0.67 0.4 1.0 1.72 2. 2.36 3. 1.37 1.66 1.81 2. 2.57 2.88 3.04 3. 3. 3.51 3.67 4. 4.46 4.78 5. 6. 6.2 1. 1. 1.38 1.76 2.01 2. 2. 2. 2.7 2.2 3. 4. 5.76 2. 2. 3. 3.52 3.77 4. 4.48 4.7 5. 5.46 5.71 5.5 6. 6.4 7. 8..48.8 2.55 3. 3.38 3.4 4. 4.52 4.80 5.0 5.37 5.67 5.6 6. 6.55 6.85 7. 7.73 8.34 8.4.84.4. 3.3 3.71 4.06 4. 5.41 5.76 6. 6.46 6.81 7. 7.51 7.87 8. 8.58.2.0.7.8.5 4. 4.74 5.27 5.78 6. 6.82 7.36 7.88 8.42 8.5.4.0.6.1.7.2.8.3.5.5.6.4.2.1 3.52 3.5 4.38 5. 5.70 6. 6.57 7.02 7.47 7.1 8.36 8.82.27.73.2.6.1.0.0..3.7.1 6. 6.84 7.57 8..07.84.6.4.1..5.3.1.8.6.4.2.8.4.0.4.6 34.7 5.70 6.31 6.4 7.57 8. 8.83.46.1.7.4.0.7.4.1.6.3.0.3.6.0 4.57 5. 6. 7.02 7.2 8.86.83.8....1.2.3.1.0.8.8 7.1 8.86.82.8.8.7.7.7.8.7.8.7.8.7.8..8. 2.0 31.1 34.3 4.41 5.03 5.67 6.34 7.02 7.75 8.4..0.8 8.85.4.0.4.2.0..7.1.5..4 2. 31.4.8 34.3.8 2.1 3. 4. 4.83 5. 5.88 6. 5.75 6.73 7.76 8.85.7.2.4..2.6 1.7 3.03 3.42 4. 5.55 6.33 7. 7.8 8.85 1.61 2. 2.80 3. 4. 5.43 1.82 50 0 0 0 0 0 500 600 700 800 2.1 3.
WARNING USE CARE TO PREVENT INJURY COMPLY WITH THE FOLLOWING TO AVOID SERIOUS PERSONAL INJURY 1. Guards must be provided on all power transmission and conveyor applications in accordance with provisions of ANSI/ASME B.1 2 Safety Standards for Mechanical Power Transmission Apparatus and ANSI/ASME B.1-0 Safety Standard for Conveyors and Related Equipment, or other applicable standards. When revisions of these standards are published, the updated edition shall apply. 2. Disconnect power, Always lock out power switch before installing, removing, or servicing unit. Comply with Occupational Safety and Health Standards.7 The Control of Hazardous Energy (Lock Out/Tag Out). 3. Install in proper enclosure in accordance with NEMA 0-1 Enclosures for Electrical Equipment (00 Volts Maximum) and NFPA 46 3 edition Purged and Pressurized Enclosures for Electrical Equipment, 3 Edition. When revisions of these standards are published, the updated edition shall apply. Affiliated Companies: U.S. TSUBAKI, INC. 1 E, Marquardt Drive Wheeling, IL 6000 U.S.A. Phone : 847--500 Facsimile : 847--5 TSUBAKIMOTO SINGAPORE PTE. LTD. Gul Lane Jurong Singapore 624 Phone : 864/3/4 Telex : TSUBAKI RS Facsimile : 860-6, Tsurumi 4-chome, Tsurumi-ku Phone : 06-6-54 Osaka 538-8686, Japan Telex : 6438 OSKTBKJ Internet: Facsimile : 06-6-01 http://www.tsubakimoto.co.jp/english/ TSUBAKIMOTO EUROPE B.V. Belder 1, 4704 RK Roosendaal, The Netherlands Phone : 05-54800 Facsimile : 05-540 TSUBAKI of CANADA LIMITED Drew Road Mississauga, Ontario, L5S 1J6 Canada Phone : 05-676-00 Facsimile : 05-676-004 TSUBAKI AUSTRALIA PTY. LTD. Unit E. 5-1 Silverwater Road Silverwater, N.S.W. 41 Australia Phone : 02-648-5 Facsimile : 02-648-31 TAIWAN TSUBAKIMOTO CO. No. 7 Feng Sun Keng Kuei Shan-Hsiang, Taoyuan-Hsien Taiwan R.O.C. Phone : 033-23827/8/ Telex : 2 TSUBAKIT Facsimile : 033-265 TSUBAKIMOTO U.K. LTD. Bingham Industrial Estate, Bingham, Nottingham NG 8GG United Kingdom Phone : 04-838554 Facsimile : 04-8 Distributed by: Note: In accordance with the policy of TSUBAKIMOTO CHAIN CO. to constantly improve its products, the specifications in this catalog are subject to change without notice. 85-K1 /8 TSUBAKIMOTO CHAIN CO. Printed in Japan K 5,000