INSTALLATION INSTRUCTIONS Accessory P/N 08L96-SZA-100A Application 2011 PILOT Publications No. AII 43295 Issue Date MARCH 2010 PARTS LIST Advanced cargo net 2 Anchors A (Large) TOOLS AND SUPPLIES REQUIRED Drill 3 mm, 5 mm, and 10.5 mm Drill bits Masking tape Tape Felt-tip pen Scale Small flat-tip screwdriver Eye protection (face shield, safety goggles, etc.) INSTALLATION 4 Anchors B 6 Self-tapping screws Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by do-it-yourselfers. NOTE: This advanced cargo net cannot be installed with the cargo liner or interior bicycle attachment. Installing the Hooks 1. Using a small flat-tip screwdriver, push and release the seat belt lower hook from each third row seat. Insert the seat belt lower hook to the fix hole. 4 Snaps Accessory User s Information Manual Push. LOWER HOOK SEAT BELT LOWER HOOK FIX HOLE 2010 American Honda Motor Co., Inc. All Rights Reserved. AII 43295 (1003) 08L96-SZA-1A00-91 1 of 6
2. Fold down the third row seats. 5. Using a felt-tip pen, measure and mark two locations on the masking tape attached in step 3. LEFT REAR SIDE PANEL FRONT FELT-TIP PEN 19 mm 96 mm 215 mm 3. Attach masking tape along the outer edge of the third row seat back board as 4. Using a felt-tip pen, measure and mark two locations on the masking tape attached in step 3. FRONT RIGHT REAR SIDE PANEL 6. While wearing eye protection, drill the two forward marked locations with a 3 mm drill bit and then with a 5 mm drill bit. Drill through the hard board and sheet metal. To prevent damage to the inner vehicle parts, wrap tape around the drill bit away from the tip as FELT-TIP PEN 96 mm 19 mm 215 mm 25 mm 3 mm 5 mm BIT 10 mm 10.5 mm BIT 7. Drill at the marked location with a 10.5 mm drill bit. To drill through the hard board only, wrap tape around the drill bit 10 mm away from the tip as 2 of 6 AII 43295 (1003) 2010 American Honda Motor Co., Inc. All Rights Reserved.
8. While wearing eye protection, drill the two rear marked locations with a 3 mm drill bit and then with a 5 mm drill bit. Drill through the hard board and sheet metal. To prevent damage to the inner vehicle parts, wrap tape around the drill bit away from the tip as 11. Using a felt-tip pen, measure and mark on the masking tape attached in step 10. FELT-TIP PEN FRONT SEAT BACK BOARD 98 mm 37 mm 3 mm 5 mm BIT 12. Using a felt-tip pen, measure and mark on the masking tape attached in step 10. 9. Remove the masking tape. 10. Fold down the second row seats. Attach two pieces of masking tape to the second row seat back board as SEAT BACK BOARD FELT-TIP PEN 97 mm 44 mm 2010 American Honda Motor Co., Inc. All Rights Reserved. AII 43295 (1003) 3 of 6
13. While wearing eye protection, drill the marked locations with a 3 mm drill bit and then with a 5 mm drill bit. Drill through the hard board and sheet metal. To prevent damage to the inner vehicle parts, wrap tape around the drill bit away from the tip as 16. Assemble the four self-tapping screws on the four anchors B. 4 ANCHORS B 4 SELF-TAPPING SCREWS 17. Install the two anchors A (Large) on the third row seat back board into the holes made in step 7. 3 mm 5 mm BIT 4 ANCHORS B (small) (Large) 14. Remove the masking tape. 15. Assemble the two self-tapping screws on the two anchors A (Large). (Large) ANCHOR A, ANCHOR B ANCHORS B Position the anchors vertically. SEAT BACK BOARD 2 SELF-TAPPING SCREWS 18. Install the four anchors B on the second and third row seat back board into the holes made in steps 8 and 13. 4 of 6 AII 43295 (1003) 2010 American Honda Motor Co., Inc. All Rights Reserved.
Installing the Advanced Cargo Net Position 1 19. Fold down the third row seats. Position 2 21. Fold the advanced cargo net and secure it with two buttons. 2 BUTTONS 22. Attach five loops on the advanced cargo net to two anchors A (Large), two anchors B and hook on the third row seat back board. (Large), 4 LOOPS HOOK LOOP (Large), 20. Attach six loops on the advanced cargo net to two anchors A (Large) and four anchors B on the second and third row seat back board. 4 LOOPS 2 HOOKS 23. Attach two loops on the advanced cargo net to two hooks. 2010 American Honda Motor Co., Inc. All Rights Reserved. AII 43295 (1003) 5 of 6
Position 3 24. Attach four snaps onto the advanced cargo net as Position 4 27. Attach two snaps onto the advanced cargo net as 4 SNAPS 2 SNAPS 25. Fold down the third row seats. (Large) 28. Attach four loops on the advanced cargo net to two hooks and two anchors B on the third row seat back board. 2 HOOKS 4 SNAPS 2 SNAPS 4 TIE-DOWN HOOKS 26. Attach four snaps on the advanced cargo net to four tie-down hooks and two loops on the advanced cargo net to two anchors A (Large) on the third row seat back board. 2 TIE-DOWN HOOKS 29. Attach two snaps on the advanced cargo net to two tie-down hooks. 6 of 6 AII 43295 (1003) 2010 American Honda Motor Co., Inc. All Rights Reserved.