odel Code Supplement Single pump model code Product A B C D E F G H J K L 1 2 3 N P 1 2 S T P Product series Code Description P Series 40 variable pump A Displacement 025 24.6 cm³/rev [1.50 in³/rev] 035 35.0 cm³/rev [2.14 in³/rev] 044 43.5 cm³/rev [2.65 in³/rev] 046 46.0 cm³/rev [2.81 in³/rev] B Type C ersion C D ersion D C Swashplate group B Standard D Seal group A Standard for DDC or DC controls B Standard for HDC, EDC, or FN controls E Input shaft / auxiliary drive (46 only) A 13 teeth, 16/32 pitch / none B 13 teeth, 16/32 pitch / SAE A flange, 9 teeth D 13 teeth, 16/32 pitch / SAE B flange, 13 teeth G 15 teeth, 16/32 pitch / none H 15 teeth, 16/32 pitch / SAE A flange, 9 teeth J 15 teeth, 16/32 pitch / SAE A flange, 11 teeth K 15 teeth, 16/32 pitch / SAE B flange, 13 teeth N 1.0 in tapered, 1/8 (1.5 in/ft) taper 1.0 in straight key Y 0.875 in straight key F otation C L CC S C, quiet valve plate T CC, quiet valve plate C, quiet valve plate Y CC, quiet valve plate 520L0635C December 2005
odel Code Supplement Single pump model Product A B C D E F G H J K L 1 2 3 N P 1 2 S T P G Charge pump displacement A None B 13.9 cm³/rev [0.85 in³/rev] S 11.8 cm³/rev [0.72 in³/rev] H Charge pressure relief valve setting B 19.5 bar [283 psi] E 11.0 bar [160 psi] G 14.0 bar [230 psi] J 21.5 bar [313 psi] J Filtration AA Suction filtration BB emote pressure filtration without bypass valve BC emote pressure filtration without bypass valve or charge pump NN None and no charge pump K Displacement limitation A No displacement limiters G Adjustable displacement limiters (factory set to max. displacement) L Bypass valve A Bypass valve 1 High pressure relief valve locations A None / None B Port A / Port B C Port A / None D None / Port B 2 520L0635C December 2005 2/3 High pressure setting, port A and B A No high pressure relief valves 140 bar [2030 psi] B 175 bar [2540 psi] C 190 bar [2755 psi] D 210 bar [3045 psi] E 230 bar [3335 psi] F 250 bar [3625 psi] G 280 bar [4060 psi] H 300 bar [4350 psi] 325 bar [4710 psi] J 345 bar [5000 psi]
odel Code Supplement Single pump model Product A B C D E F G H J K L 1 2 3 N P 1 2 S T P N Controls AB anual displacement (DC) AT anual displacement with neutral start switch (NSS) terminals BA Hydraulic displacement (HDC) 1-11 bar [15-160 psi] CB Electric displacement (EDC), single coil, Packard-connector CD Electric displacement (EDC), single coil, S-connector CE Electric displacement (EDC), dual coil, Packard-connector DA Electric 3-position (FN) solenoid (12 DC) D Direct displacement (DDC), right side DL Direct displacement (DDC), left side P DC handle position A Non-DC control D Down U Up 1 position code corresponds to the supply orifice for DC or DDC control, or orifice A for EDC or HDC control. 2 position code corresponds to the drain orifice for DC or DDC control, or orifice B for EDC or HDC control. eference N position code for pump control type. 1/2 DC or DDC control orifice diameters, supply and drain A Ø 0.8 mm [0.031 in] B Ø 0.9 mm [0.036 in] C Ø 1.0 mm [0.041 in] D Ø 1.2 mm [0.046 in] F No orifice 1/2 EDC or HDC control orifice diameters, orifice A and B G Ø 1.4 mm [0.055 in] H Ø 0.9 mm [0.036 in] J No orifice S Auxiliary mounting pad A SAE A, 9 teeth D SAE A, 11 teeth B SAE B, 13 teeth C None T Special hardware features NNN None CNN Tapered trunnion bearing 520L0635C December 2005 3
odel Code Supplement code P T Product series Code Description PT Series 40 tandem pump A Displacement 025 2 x 24.6 cm³/rev [2 x 1.50 in³/rev] 035 2 x 35.0 cm³/rev [2 x 2.14 in³/rev] 044 2 x 43.5 cm³/rev [2 x 2.65 in³/rev] 046 2 x 46.0 cm³/rev [2 x 2.81 in³/rev] B Type C ersion C D ersion D E Input shaft S 13 teeth, 16/32 pitch A 15 teeth, 16/32 pitch B 19 teeth, 16/32 pitch C 1.0 in tapered, 1.5 in/ft K 0.875 in straight key F otation C L CC S C, quiet valve plate, opp. side porting, without charge pump T CC, quiet valve plate, opp. side porting, without charge pump C, quiet valve plate Y CC, quiet valve plate C, quiet valve plate, opp. side porting, with charge pump Z CC, quiet valve plate, opp. side porting, with charge pump G Charge pump displacement A None C 22.9 cm³/rev [1.40 in³/rev] 16.4 cm³/rev [1.00 in³/rev] 4 520L0635C December 2005
odel Code Supplement P T H Charge pressure relief valve setting B 19.5 bar [283 psi] E 11.0 bar [160 psi] G 14.0 bar [230 psi] J 21.5 bar [313 psi] J Filtration AA Suction filtration BB emote pressure filtration without bypass valve BC emote pressure filtration without bypass valve or charge pump NN None and no charge pump C/Q Swashplate group B Standard D Seal group A Standard for DDC and DC controls, front pump B Standard for HDC, EDC, and FN controls, front pump C Standard for DDC and DC controls, rear pump D Standard for HDC, EDC, and FN controls, rear pump K/U Displacement limitation A No displacement limiters G Adjustable displacement limiters (factory set to max. displacement) L/X Bypass valve A Bypass valve 1/1 High pressure relief valve locations A None / None B Port A or C / Port B or D C Port A or C / None D None / Port B or D 520L0635C December 2005 5
odel Code Supplement P T 2/3 High pressure setting, port A and B A No high pressure relief valves 140 bar [2030 psi] B 175 bar [2540 psi] C 190 bar [2755 psi] D 210 bar [3045 psi] E 230 bar [3335 psi] F 250 bar [3625 psi] G 280 bar [4060 psi] H 300 bar [4350 psi] 325 bar [4710 psi] J 345 bar [5000 psi] 6 520L0635C December 2005 2/3 High pressure setting, port C and D A No high pressure relief valves 140 bar [2030 psi] B 175 bar [2540 psi] C 190 bar [2755 psi] D 210 bar [3045 psi] E 230 bar [3335 psi] F 250 bar [3625 psi] G 280 bar [4060 psi] H 300 bar [4350 psi] 325 bar [4710 psi] J 345 bar [5000 psi] N/Y Controls AB anual displacement (DC) AT anual displacement with neutral start switch (NSS) terminals BA Hydraulic displacement (HDC) 1-11 bar [15-160 psi] CB Electric displacement (EDC), single coil, Packard-connector CD Electric displacement (EDC), single coil, S-connector CE Electric displacement (EDC), dual coil, Packard-connector DA Electric 3-position (FN) solenoid (12 DC) D Direct displacement (DDC), right side DL Direct displacement (DDC), left side P/Z DC handle position A Non-DC control D Down U Up
odel Code Supplement 1 position code corresponds to the supply orifice for DC or DDC control, or orifice A for EDC or HDC control on front pump. 2 position code corresponds to the drain orifice for DC or DDC control, or orifice B for EDC or HDC control on front pump. eference N position code for front pump control type. 1 position code corresponds to the supply orifice for DC or DDC control, or orifice A for EDC or HDC control on rear pump. 2 position code corresponds to the drain orifice for DC or DDC control, or orifice B for EDC or HDC control on rear pump. eference N position code for rear pump control type. P T 1/2 DC or DDC control orifice diameters, supply and drain A Ø 0.8 mm [0.031 in] B Ø 0.9 mm [0.036 in] C Ø 1.0 mm [0.041 in] D Ø 1.2 mm [0.046 in] F No orifice 1/2 EDC or HDC control orifice diameters, orifice A and B G Ø 1.4 mm [0.055 in] H Ø 0.9 mm [0.036 in] J No orifice 1/2 DC or DDC control orifice diameters, supply and drain A Ø 0.8 mm [0.031 in] B Ø 0.9 mm [0.036 in] C Ø 1.0 mm [0.041 in] D Ø 1.2 mm [0.046 in] F No orifice 1/2 EDC or HDC control orifice diameters, orifice A and B G Ø 1.4 mm [0.055 in] H Ø 0.9 mm [0.036 in] J No orifice S Auxiliary mounting pad A SAE A, 9 teeth D SAE A, 11 teeth B SAE B, 13 teeth C None T Special hardware features NNN None 520L0635C December 2005