Table Of Contents Wire 00 Vacuum Top Adjustment Auxiliary Coil General Guide Mechanical Bottle Bottom Drawout and Assemblies Assemblies Harnesses Assemblies Guide Terminal information 800 Bottle Contactor Interlocks Tool Amp Latch Assemblies Assemblies Kits Assemblies Contactors Parts CRI9B, C & D Renewal Pals Bulletin ~ 6 6 6 7 8 8 8 rhese instructions do not purport to cover all details or variations in equipment for every possible contingency to be met in connection with nstallation, operation, or maintenance. Should further information be desired or should particular problems arise which are not covered sufficiently for the Purchaser's purposes, the matter should be referred to the nearest GE SaIA!: Offi"A
CRI9B, C & D Renewal Parts Bulletin General Information This renewal parts bulletin will provide the proper identification of standard parts which may be required for the maintenance of CR9B & D (00A) and CR9C (800A) Vacuum Limitamp contactors. iboth the complete contactors and required renewal parts are shown as catalog numbers and are supported by photographs. Catalog numbers identified in this bulletin may not be the same as those parts on the original equipment. The renewal part catalog numbers are shown in kit form. It is the intent of this bulletin to give our customers a quick and accurate way to identify parts required for normal maintenance of the Vacuum Limitamp contactors. Unless otherwise stated, all of the parts shown in the bulletin are compatible with the contactors manufactured since 98. Since contactors are supplied to meet specific customer control and distribution requirements, certain replacement parts not listed in this publication may occasionally be required. Please refer to the factory for these requests. In these situations, please provide a complete description of the part, along with the complete data shown on the contactor nameplate that is affixed to the top of the contactor. For pricing and availability of parts shown in this bulletin, contact your nearest GE sales office. ~ttention should be g iven to forecasting lour particular renewal parts requirements :0 ensure on-site availability of the specific )arts as required for normal maintenance ~nd proper operation of your equipment. ro maintain maximum operating efficiency nd reliability of your equipment, genuine E renewal parts are recommended.
CRI.9.B, C & D Renewal Pal'fs Bulletin 00A and 800A Vacuum Contactor Fig. Contactors can be identified by their catalog number, located on the nameplate on the top of the contactor. Note: 00A contactor shown in photo 00 Amp Contactor 800 Amp Contactor CR9B & D Vacuum contactors are designed for equipment used in starting AC motors with line voltages from 000-Volts to a maximum of 700-Volts, transformer feeders, and other medium voltage control equipment Contactor Bracket and Pin Assembly Control Wire Harness Plug Bracket and Socket Assembly (not shown) CR9C Vacuum contactors are designed for equipment used in starting AC motors with line voltages from 000-Volts to a maximum of O00-Volts, transformer feeders, and other medium voltage control equipment BG See Fig. BG Contactor Catalog Number System + Voltage for contactor main coil is always 0/ VOC * The sum of normally open, normally closed, and late opening normally closed ~ contacts must be a multiple of five (). Each interlock block contains five () contacts. A contactor may contain a maximum of four () blocks, two () being the maximum on either side. Only five () late opening normally closed contacts are available on a contactor. Typical contactor number: CR9Bll0LO00U
CR9.:E, C& D Fenewal Parts Bulletin Fig. Fig. Coil Assembly ~cription rn9b rn9c, & D, 00 arrp contactor 800 arrp contactor pan NurTJer D78~ D780GR Note".00\ coil shown in pooto Fig. Fig..e \~' 00 o o Vacuum Bottle Assembly Guide Assembly ption Part NurrtJer - O70000GR' CR9B & D, 00 a"'p contactor Part NurTiJer O7reCXR' CR9C, 800 an-p contactor
CRI9.B, C & D Renewal Parts Bulletin Fig. 6 Fig. 7 ~ Contactor Top Assembly Contactor Adjustment Tool Kit CR98 & D, 00 amp contactor D78008GR CR98 & D, 00 amp contactor 0A900DCGl CR9C,800 ampcontactor D780GR CR9C, 800 amp contactor 0A900DCG Note: 00A top assembly shown in photo Note: 00A tool kit shown in photo Fig. 8 Mechanical latch Assembly 0/ VDC VDC C67989GRA C67989GRB
CRI9.B, C & D Renewal Parts Bulletin Fig. 9 800 Amp Block 00 Amp Block Auxiliary Interlocks The table below lists all possible combinations of auxiliary interlocks within a single block. Select the contact arrangement desired and add the suffix letters to the appropriate part number (i.e.. C679809GRP). Contactor CR9B & D, 00 Amp contactor CR9C, 800 Amp contactor C679809- C6798- Suffix GlRP GRP GRP GRP GRP G6RP G7RP GBRP G9RP GlORP GllRP NO NC LONG Suffix GRP GRP GRP GRP G6RP G7RP G8RP G9RP G0RP GRP NO NC LONG
Drawout Contactor (CR9D) Parts ~ CR9B, C & D Renewal Parts Bulletin Fig. 0 Fig. Bottle Guide Bottle Guide Assembly Bottom Terminal Assembly D escription CR9B & D, 00A contactor CR9C, 800 A contactor Note: 00A top assembly shown in photo D780GR D7807GR CR9B, 00A contactor CR9D,00A drawout contactor CR9C, 800A contactor Note: 00A terminal parts shown in photo D78008GR D78008GR D780GR Fig.