LOCKER PRICING. Effective November 1, 2016

LOCKER PRICING Effective November 1, 2016 PENCO STEEL SURCHARGE EFFECTIVE 4/28/17. ADD 5% TO LIST PRICES. THIS STEEL SURCHARGE WILL NOT APPLY TO TEXTILE RENTAL PRODUCTS, PLASTIC LOCKERS, LOCKS, WOOD BENCHES, ETC. D UFFEL LOCKER TM D UFFEL LOCKER Penco's newest locker, page 30 pencoproducts.com

Contents General Information...3 Footnote Codes...4 Lockers Vanguard Unit Pack Lockers...4 Vanguard Bulk Pack Lockers... 5-7 Recessed Handle Vanguard... 7-8 Guardian Lockers...9 Guardian Medallion Lockers...10 Guardian Plus Lockers... 10-11 Guardian Defiant II Lockers... Invincible II Basic Units & Group Ends... 13- Invincible II Defiant II Basic Units...16 Stadium Locker (KD and Welded)...17 All-Welded Lockers... -20 All-Welded Defiant II Single Point Latch...21 Angle Iron Welded Lockers... 22-23 Patriot Gear & Turnout Lockers and Accessories... 24-27 Patriot Duty Lockers and Accessories... 28-29 Rapid Response Duffel Locker... 30-32 General Locker Accessories & Components Locker Features and Options...33 Ventilation Options and Specialty Doors... 34-35 Perforate Locker Shelves... 34-35 Delete Diamond Perforations... 34-35 Add Mini Louvers/Slam Latch... 34-35 Quiet Sound Dampening Pans...34 Color, Finishes & Electro Galvanizing for Lockers...35 Paint/Touchup...36 Slope Top Kits...37 Individual Unit Slope Tops (24 Ga.)...37 Continuous Slope Hoods... 37-38 Hip Fillers...38 Front & End Bases...38 Zee Bases...39 Fillers, Standard & Custom... 39-40 Recess Trim...40 Extra Locker Shelves (24 & 16 Ga.)...41 Upgrade Shelves, Tops, Bottoms from 24 Ga. to 16 Ga., Extra Cost..41 Electrogalvanizing 16 ga. Shelves, Tops & Bottoms...42 Custom 16 Gauge Locker Ends...42 16 Ga. Exposed Locker Ends...42 Finished End Panels... 43-47 Partitions - 24 Ga...48 Inner Compartment Door...48 Interior Subdivisions & Accessories for Executive Locker...48 Miscellaneous Locker Accessories...48 Packing House Lockers...48 Locker Room Benches/Pedestals...49 Locks Lock Information Form...49 Flat Key Locks - Built-in...49 Lock Application Table...50 Master Locks and Zephyr Locks... 51-52 Safe-O-Mat Coin Operated Locks/Diglocks...52 Miscellaneous Locker Parts Door & Frame Assemblies... 53-54 Vanguard Latch Channels/Miscellaneous Locker Parts... 54-55 Misc. Parts & Hardware, Defiant II-R Conversion Kits/Backs...56 Divisions...57 Slope Tops (2 Tier)/Tops & Bottoms/Basket Racks & Baskets...58 Miscellaneous Information Welded Locker Order Information Form...59 Starter and Adders Method of Pricing...60 ADA Locker Requirements / Locker Care...61 Shelf (TAB), Partition & Lower Tier Head Location & Usage / Metric...62 Lockers A to Z (illustrated accessories in use) / Locker "Growth"...63 With the exception of Welded Lockers, pricing is based on lockers shipped unassembled, otherwise known as Knocked Down (KD). For assembly at Penco, see additional charge on page 3. Locker Construction Overview Available in 24 COLORS Except QuickShip Vanguard Lockers have louvered doors. All 1 Tier (except for " high model), 2 Tier, 2 Person and Duplex lockers have a zinc alloy die-cast pull-out lockable Vanguard handle on each main door and a multi-point door latch system. Three tier Vanguard lockers with catalog numbers beginning with 64 also have Vanguard handles and multi-point latch doors. Three tier lockers with a catalog number beginning with 63 and 4, 5 & 6 Tier, 16 person and Wall Mounted Locker Coat Rack lockers (as well as " high 1 Tier lockers) are known as box lockers and have a friction catch latch/door pull. 7 & 8 Person lockers plus Box Over Lockers use a combination of the 2 latch types. Most Vanguard lockers are available packed two different ways: Vanguard Unit Pack Lockers: Vanguard Unit Pack Lockers are the same as Bulk packaged lockers, except that they are prepackaged with all the required parts for assembly in one carton (2 cartons for Wall Mounted Locker and 3 cartons for 16 Person Lockers). See the separate QuickShip Price list for selected items available for shipment in 5 days or less in a limited color selection. Vanguard Bulk Pack Lockers: Like parts are packed together. The standard 6" legs can be deleted by specifying on the order. Recessed Handle Vanguard Lockers are the same as Vanguard, except that a recessed handle replaces the die-cast Vanguard pull-out handle on the 1, 2 & 3 Tier, 2 Person, Duplex, Dual, Executive, 7 & 8 Person and Box Over Locker. Available as standard on 1, 2 & 3 Tier QuickShip lockers. Guardian Lockers have Recessed handles and no louvers. Guardian "Medallion Option" Lockers are the same as Guardian except that a quiet sound deadening pan is welded to the inside of the door. Guardian Plus Lockers are the same as Guardian, except that the doors are 14 gauge steel. Invincible II Heavy Duty Athletic Lockers are made from heavier gauge steel (14 ga. doors, 16 ga. sides, tops, bottoms and shelves, ga. backs) and have diamond-shaped perforations on the doors and sides. Recessed handles are standard on 1, 2 & 3 Tier models; standard box lockers have door pulls. A perforated or solid Group End must be ordered for each group of lockers, or row end. Stadium Lockers are available in Welded and KD construction. They have open fronts for ease of access. Several configurations are available. Patriot Lockers are also available in Welded and KD construction. "Turnout" models have open fronts for ease of access and "Gear" models have doors. KD Gear locker doors are shipped loose on 30" & wider models. "Duty" locker models include specialized interior configurations. A special assortment of accessories is available. Rapid Response Duffel Lockers are available in KD construction with double doors and Cremone handle with a one wide configuration. Welded Lockers are shipped completely assembled except for hardware items such as number plates & locks. All major components are welded together at the factory prior to being painted with a durable baked-on enamel finish. Locker groups up to 54" wide can be shipped as units for All-Welded and All-Welded Defiant II lockers. Defiant II Single Point Latch (SPL) Option provides a 14 gauge door with single point latching in a recessed handle with no moving parts. This option can be added to the Guardian, Invincible II, All-Welded, Angle Iron and select Patriot models Lockers. Footnotes Letter codes appear in the "Note" column next to the appropriate line items in this price book. Explanation keys are shown on page 4. Note that combined footnotes such as "P" and "V" would be shown as PV". Customer must specify color in writing on all orders.

General Information All prices are based on Penco Standard Construction. Unless otherwise specified, all products are shipped knocked down (unassembled) from the factory. All orders are subject to final acceptance at the main office. SPECIFICATIONS: Refer to current Penco catalogs or website for descriptions and specifications (subject to change without notice). LEAD TIMES: See the Penco website for lead times. See the QuickShip Price List for selected items available for shipment within 5 working days. LEGS: "Legs" or "No Legs" must be specified on locker purchase orders. KD Lockers are priced the same with or without legs. Locker HEIGHTS in this book represent nominal opening height on 1Tier, 2T, 3T, 4T, 5T, 6T, 8T & 9T; overall body height on others. Height does not include legs. KD Lockers will be furnished with 6 legs unless otherwise specified. Stadium, Patriot and Rapid Response Duffel lockers are not offered with legs. LOCKS: Must be ordered separately. ASSEMBLY AT PENCO: Factory assembly extends the lead time. Factory assembly of lockers will be done with rivets. Locker assembly will be done in groups of up to 3 frames wide unless otherwise specified and authorized in advance. Assembled groups shall not exceed 54" in width. Locker accessories are packaged separately. NET Per Frame Assembly Charges Locker Type Vanguard Guardian Invincible II Stadium & Patriot Rapid Response Duffel Locker 1, 2 & 3 Tier $.00 $.00 $.00 n/a $65.00 4, 5 & 6 Tier $.00 n/a $.00 n/a $75.00 8 & 9 Tier $45.00 n/a $45.00 n/a n/a 2 Person $35.00 $35.00 n/a n/a n/a Duplex $35.00 $35.00 n/a n/a n/a 16 Person $54.00 n/a n/a n/a n/a Wall Mount $.00 n/a n/a n/a n/a Box Over $25.00 n/a n/a n/a n/a Double Door $25.00 n/a n/a n/a n/a Executive $50.00 n/a n/a n/a n/a Stadium/Patriot n/a n/a n/a $50.00 n/a BULK PACK LOCKER GROUPING: Bulk Pack Vanguard and Guardian KD lockers (except for the Vanguard xx13-5/8 1-tier box locker) are sold by the frame (Per = Frm. ), and are provided with sufficient locker divisions for assembly in groups of 3-wide. Unless specifically noted as 1 wide in the price book, for 1-wide lockers, add 20% to the per frame price in the price book. For a 2-wide group, add 10% to each frame price. For single frame groupings of 24 wide lockers add 10%. This pricing also applies to lockers assembled by Penco. To make 24" wide lockers more manageable, we recommend ordering in smaller groups. STARTERS AND ADDERS: For building wider groupings of Vanguard or Guardian bulk pack lockers at the project site (4-wide or more), the STARTER and ADDER method may be ordered, see page 60. NUMBER PLATES: Price includes one number plate per opening with up to four digits. Plates 1 to 1000 and blank are kept in stock. 1001 to 00 will ship from Hamilton, NC facility with a lead time of 3-4 weeks. If no sequence is specified, Penco will supply from 1 up per order. For over 100 openings, the number sequence must specified. For alphanumeric or numbers above 00 (6 spaces maximum), and number plate delivery can take 4-5 weeks. Any number sequence other than 1 to 00 and blanks are considered a special order and will carry a $50 NET setup charge with a 4-5 week lead time. On factory-assembled lockers, number plates are packaged separately for field installation. RIVETS: Standard locker hardware supplied is nuts & bolts. To obtain rivets in lieu of standard nuts & bolts, add $5.25 list per frame to price of locker, and mark the order clearly to specify "RIVETS". OVERALL DIMENSION DISCLAIMER: Penco's internal system rounds up sizes to reflect whole numbers. For example: a 36.5 high locker, which is truly 36.5 in overall height, will list on the order acknowledgement as 37. 0 Tawny Tan 021 Gray Ash 028 Gray 052 Reflex Blue 054 Canvas 055 Shamrock 056 Sunburst 058 Nordic Purple Color Selection - 24 Standard Colors 073 Champagne 701 Spray Green 710 Sagebrush Yellow 7 Lake Blue 720 Mandarin Orange 722 Patriot Red 723 Light Putty 736 Burgundy 767 Cardinal Red 806 Marine Blue 8 Hunter Green 822 Regal Blue 826 Slate Blue 848 January White 949 Jet Black 952 Turquoise Teal COLOR: All locker orders must have color specified prior to receiving a scheduled ship date. Penco s standard finish is hybrid powder coat. See page 36 for additional paint finish information. ENGINEERING DRAWINGS OR SPECIAL ENGINEERING: Engineering drawings for approval require additional time. Such drawings can be supplied only on an order of $10,000 total price book value or more. Shipment for this type of order can be scheduled only after receipt of approved drawings. Shipment for this type of order normally requires 6 to 8 weeks after receipt of approved drawings. Non-standard fillers and trim can be supplied only on orders for $4000 list price or more. Any orders cancelled after the drawings are completed will incur a cancellation fee. SINGLE ROW (SR) & DOUBLE ROW (DR): All pricing in this book is for single row lockers. For pricing on double row lockers (back-to-back, with double-deep divisions and shared backs), contact a Penco representative. LOCKER DOOR GAUGES: Locker doors are 14 gauge steel except Vanguard, Standard Guardian and Guardian Medallion. Vanguard, Standard Guardian and Guardian Medallion doors with Vanguard or recessed handles are 16 ga. if " wide or wider; 7-1/2" and 9" wide are ga. Vanguard box locker doors (with door pull) are 16 ga. if " wide or wider; 9" and " wide are ga. LEFT HAND (LH) & RIGHT HAND (RH) are determined from the point of view of a person facing a locker. Right Hand doors have the hinges on the right side and are standard on all lockers. 2 Person, Duplex and 24" wide single tier Double Door lockers have Right Hand and Left Hand doors. SMALL ORDER POLICY: MINIMUM ORDER - $50.00 Net plus shipping costs. PACKAGING AND MARKING: For special crating, marking, palletizing, or export packing, contact a Penco Representative for availability and cost. For heat-treated pallets, add the following to the estimate/purchase order: Add $10 NET per pallet (roughly 1 pallet per 1000 lbs). WEIGHT: Weights shown are approximate shipping weights for average packing per average order. CHANGES & CANCELLATIONS: Orders changed after scheduling but before manufacturing are subject to a minimum $100.00 net charge, if approved by the main office. Changes may have an adverse effect on scheduled ship date. Orders are not subject to changes or cancellations after commencement of manufacturing. Orders requiring engineering drawings are subject to an engineering fee if cancelled. CLAIMS AND FREIGHT DAMAGE: If freight arrangements are 3rd party or collect, claims for damage or short must be filed by the Penco distributor/customer with the delivering carrier. For pre-pay and add shipments, all claims for shortages and damages must be made in writing to the main office within 72 hours from receipt of shipment. Caution: When the delivering carrier is given a clear receipt for a shipment in which there is damaged merchandise or a shortage, the carrier is relieved of further responsibility. Penco will not accept return of merchandise damaged in transit. The claim is with the delivering carrier. SHIPPING CHARGES: All shipments will be made pre-pay and add unless otherwise specified. When freight is prepaid, charges will be added to the invoice. Each order must be for one destination to one consignee. RETURN SHIPMENTS: No return shipments will be accepted without previous written factory authorization. A restocking charge of 35% or more with a minimum of $50.00 net will be levied on all authorized material subject to inspection for damage at the factory. Special orders including welded lockers or factory assembled products are NOT eligible for return. No credit will be issued for damaged material. Material returned without authorization will be refused. All return freight charges must be prepaid. GUARANTEE: We guarantee our products for a one year limited warranty to be free from mechanical and manufacturing defects. Penco is not responsible for products damaged by misuse, abuse or any acts of vandalism. The guarantee is also voided if the finish is exposed to items such as high humidity, chlorine salts, abrasive cleaners, germicidal cleaners or acids. ABBREVIATIONS: In the "Per" column, the following apply: 'Frm.' = Frame. 'Ea'. = Each. In the "Std. Pkg." column, 'LPP' = Like Parts Packed together. Elsewhere, 'SPL' = Single Point Latch Defiant II; 'SR' = Single Row, and 'DR' = Double Row ("back-toback"); 'LH' = Left Hand and 'RH' = Right Hand. ANCHORING: For safety purposes, all lockers should be floor and wall anchored. Even when properly anchored, lockers are NOT designed to withstand stepping on bottoms or swinging on doors. PENCO ASSUMES NO RESPONSIBILITY FOR PRODUCT FAILURE OR PERSONAL INJURY IF PRODUCTS ARE MODIFIED OR USED FOR OTHER THAN THEIR DESIGNED PURPOSE. Penco Products Inc. 3

Footnote Codes / Vanguard UNIT PACK Lockers Vanguard Unit Pack Lockers: Unit packaged Vanguard lockers are the same lockers as Bulk Pack lockers, except that they are pre-packaged with all the required parts for assembly in one carton (2 cartons for Wall Mounted Locker; 3 cartons for 16 Person Lockers). The catalog numbers on this page are for packaging purposes only. Specify the color, if the locker is to have 6" legs or no legs, and what type of handle required on 1, 2 and 3-tier lockers. These are NOT QuickShip lockers. Footnote Codes for this Price List P: See Locker Price List for possible extra punching charges V: If locks are required for 2 Person or Duplex lockers, order 2 per frame; 1-RH & 1-LH. X: If slope top is required, use continuous slope hoods, and field cut to size. Y: Has double doors. Vanguard Unit Packaged Lockers 1 Tier, 1 Wide 60 68001 249.05 Frm. 50.0 60 68011 259. Frm. 52.0 60 68021 273.25 Frm. 57.0 72 68051 272.30 Frm. 57.0 72 68061 281.70 Frm. 65.0 72 68071 296.80 Frm. 69.0 72 68091 321.95 Frm. 71.0 72 68101 343.45 Frm. 83.0 1 Tier, 3 Wide 60 68003 207.55 Frm. 44.0 60 68013 2.95 Frm. 45.0 60 68023 227.70 Frm. 47.0 72 68053 226.90 Frm. 49.0 72 68063 234.75 Frm. 51.0 72 68073 247.35 Frm. 55.0 72 68093 268.30 Frm. 65.0 72 68103 286.20 Frm. 73.0 2 Tier, 1 Wide 30 68111 317. Frm. 52.0 36 681 332.75 Frm. 56.0 36 68131 346.90 Frm. 62.0 36 68141 360.00 Frm. 66.0 36 68261 386.50 Frm. 76.0 2 Tier, 3 Wide 30 68113 264.30 Frm. 45.0 36 683 277.30 Frm. 50.0 36 68133 289.10 Frm. 52.0 36 68143 300.00 Frm. 56.0 36 68263 322.10 Frm. 68.0 3 Tier, 1 Wide (with 2- Point Latch) 24 68331 424.85 Frm. 58.0 24 68341 434.10 Frm. 64.0 24 68351 448.50 Frm. 68.0 3 Tier, 3 Wide (with 2- Point Latch) 24 68333 354.05 Frm. 51.0 24 68343 361.75 Frm. 57.0 24 68353 373.75 Frm. 60.0 5 Tier Box Locker, 1 Wide 68161 323.95 Frm. 50.0 68171 329.00 Frm. 55.0 5 Tier Box Locker, 3 Wide 68163 269.95 Frm. 45.0 68173 274. Frm. 50.0 6 Tier Box Locker, 1 Wide 68191 378.25 Frm. 60.0 68201 388.60 Frm. 66.0 68211 408.80 Frm. 72.0 6 Tier Box Locker, 3 Wide 68193 3.20 Frm. 54.0 68203 323.85 Frm. 60.0 68213 340.65 Frm. 66.0 16 Person Ships in 3 cartons per unit. 69 72 68231 1107.25 Unit 0.0 Wall Mount Locker Height shown is body height including top and bottom door frames. One frame of four "D x "H (nominal) openings side by side with total overall width of 45". Includes brackets and coat rod to mount beneath body. Flat top, no legs only. Ships in 2 cartons. 45 13-5/8 68242 450. Unit 43.0 LPP 4 Penco Products Inc. HEIGHT: Height shown is the nominal opening height for 1, 2, 5, & 6 tier lockers. It represents the overall height of the frame for all others. Height does NOT include 6" legs.

Vanguard Bulk Pack Lockers Vanguard Bulk Pack Lockers: Same as Unit Pack Lockers on the previous page except that like parts are packaged together (LPP). Lockers are available in any standard Penco color, with or without legs (6" legs are standard). Lockers are shipped Knocked Down (KD). Doors are 16 or GA. and body parts are 24 GA. 16 Person lockers and lockers labeled as "Box Lockers" have padlock staples and friction catch door pulls. All other lockers have a cast Vanguard handle and a multi-point latch system. Doors have louvers and accept number plates (included). NOTE: Only lockers 48-1/2" high and taller include a hat shelf. 30-1/2" and 36-1/2" high lockers are not pre-punched to accept shelves. Vanguard Lockers 1 Tier Box Locker (") Standard box locker construction with internal friction catch, door pull and padlock hasp. Actual door height is 11-1/2". Priced for one-wide assembly. Only available without legs. 13-5/8 67V 149.95 Frm. 11.0 LPP 13-5/8 69V 2.90 Frm..0 LPP 13-5/8 6179V 6.05 Frm. 13.0 LPP 1 Tier Half Height (30-1/2", hat shelf NOT included) One half of a 2 Tier locker, includes Vanguard handle and latch channel. 30-1/2 6137V 145.70 Frm. 22.0 LPP 30-1/2 6139V 149.35 Frm. 25.0 LPP 30-1/2 6147V 2.60 Frm. 28.0 LPP 1 Tier Half Height (36-1/2", hat shelf NOT included) 36-1/2 6107V 9.95 Frm. 26.0 LPP 36-1/2 67V 167.95 Frm. 27.0 LPP 36-1/2 69V 174.50 Frm. 29.0 LPP 1 Tier (48-1/2" H) 48-1/2 6176V 193.00 Frm. 38.0 LPP 48-1/2 64V 202.65 Frm. 39.0 LPP 48-1/2 67V 214.05 Frm. 40.0 LPP 1 Tier (60") 9 60 6101V 191.35 Frm. 39.0 LPP 9 60 6103V 195.45 Frm. 41.0 LPP 9 60 6105V 205.90 Frm. 44.0 LPP 60 6111V 207.55 Frm. 44.0 LPP 60 6113V 2.95 Frm. 45.0 LPP 60 61V 227.70 Frm. 47.0 LPP 21 60 6117V 242.60 Frm. 53.0 LPP 24 60 61V 258.35 Frm. 55.0 LPP 60 6119V 230.05 Frm. 52.0 LPP 60 61V 232.65 Frm. 54.0 LPP 60 63V 248.75 Frm. 57.0 LPP 21 60 65V 259.20 Frm. 59.0 LPP 24 60 66V 271.25 Frm. 61.0 LPP 60 6100V 253.50 Frm. 52.0 LPP 60 6134V 265.50 Frm. 56.0 LPP 60 6131V 278.05 Frm. 60.0 LPP 21 60 6133V 291.20 Frm. 63.0 LPP 24 60 6135V 305.20 Frm. 66.0 LPP 24 60 6149V 391.70 Frm. 74.0 LPP 24 21 60 68V 401.70 Frm. 77.0 LPP 24 24 60 6160V 4.90 Frm. 80.0 LPP 1 Tier (60") Double Doors 24 60 Y 6141V 464.70 Frm. 76.0 LPP 24 21 60 Y 6143V 474.65 Frm. 79.0 LPP 24 24 60 Y 6145V 486.90 Frm. 82.0 LPP 1 Tier (72") 9 72 61V 205.00 Frm. 46.0 LPP 9 72 63V 211.60 Frm. 48.0 LPP 9 72 65V 223. Frm. 51.0 LPP 72 6161V 226.90 Frm. 49.0 LPP 72 6163V 234.75 Frm. 51.0 LPP 72 6165V 247.35 Frm. 55.0 LPP 21 72 6167V 261.65 Frm. 61.0 LPP 24 72 6168V 276.85 Frm. 66.0 LPP 72 6169V 254.80 Frm. 58.0 LPP 72 6171V 256.40 Frm. 62.0 LPP 72 6173V 268.30 Frm. 65.0 LPP 21 72 6175V 281.40 Frm. 69.0 LPP 24 72 6177V 295.35 Frm. 72.0 LPP 72 6110V 261.75 Frm. 69.0 LPP 72 60V 273.70 Frm. 71.0 LPP 72 61V 286.20 Frm. 73.0 LPP 21 72 63V 298.45 Frm. 77.0 LPP 24 72 65V 325.35 Frm. 78.0 LPP 24 72 6196V 419.75 Frm. 88.0 LPP 24 21 72 6198V 433.85 Frm. 91.0 LPP 24 24 72 6199V 457.95 Frm. 94.0 LPP 1 Tier (72") Double Doors 24 72 Y 6191V 496.90 Frm. 90.0 LPP 24 21 72 Y 6193V 5.95 Frm. 93.0 LPP 24 24 72 Y 6195V 535.05 Frm. 96.0 LPP 1 Tier (84") 84 6013V 248.10 Frm. 56.0 LPP 84 6014V 257.25 Frm. 58.0 LPP 84 60V 272.60 Frm. 60.0 LPP 84 6016V 280.85 Frm. 65.0 LPP 84 6017V 290.35 Frm. 67.0 LPP 84 60V 297.75 Frm. 70.0 LPP 2 Tier (48.5") WITH 2 Point Latch 24 6019V 237.30 Frm. 40.0 LPP 2 Tier (60") 9 30 6201V 2.70 Frm. 36.0 LPP 9 30 6203V 226.85 Frm. 40.0 LPP 9 30 6205V 238.55 Frm. 42.0 LPP 30 6211V 264.30 Frm. 45.0 LPP 30 6213V 270. Frm. 48.0 LPP 30 62V 276.00 Frm. 54.0 LPP 21 30 6217V 287.35 Frm. 60.0 LPP 24 30 6200V 282.05 Frm. 64.0 LPP 30 6227V 287.95 Frm. 54.0 LPP 30 6229V 295.50 Frm. 58.0 LPP 30 6237V 301.80 Frm. 60.0 LPP 21 30 6257V 316.00 Frm. 62.0 LPP 24 30 6258V 317.40 Frm. 66.0 LPP HEIGHT: Height shown is the nominal opening height for 1, 2, 5, & 6 tier lockers. It represents the overall height of the frame for all others. Height does NOT include 6" legs. Penco Products Inc. 5

Vanguard Bulk Pack Lockers 2 Tier (72") 9 36 6221V 239.30 Frm. 44.0 LPP 9 36 6223V 246.50 Frm. 46.0 LPP 9 36 6225V 255.20 Frm. 52.0 LPP 36 6231V 277.30 Frm. 50.0 LPP 36 6233V 289.10 Frm. 52.0 LPP 36 6235V 300.00 Frm. 56.0 LPP 21 36 62V 305.70 Frm. 64.0 LPP 24 36 6220V 320.30 Frm. 72.0 LPP 36 6239V 303.90 Frm. 59.0 LPP 36 6241V 308.60 Frm. 60.0 LPP 36 6243V 322.10 Frm. 68.0 LPP 21 36 6245V 336.20 Frm. 74.0 LPP 24 36 6246V 349.00 Frm. 84.0 LPP 36 6219V 327.00 Frm. 70.0 LPP 36 6259V 341.30 Frm. 74.0 LPP 36 6247V 356.20 Frm. 78.0 LPP 21 36 6249V 371.75 Frm. 84.0 LPP 24 36 6250V 381.70 Frm. 90.0 LPP 24 24 36 6274V 514.25 Frm. 96.0 LPP 2 Tier (84") 42 6251V 280.65 Frm. 56.0 LPP 42 6253V 292.75 Frm. 60.0 LPP 42 6255V 305.85 Frm. 64.0 LPP 42 6073V 307. Frm. 65.0 LPP 42 6261V 320. Frm. 68.0 LPP 42 6263V 333.40 Frm. 72.0 LPP NOTE: These 3 Tier Vanguard lockers are equipped with cast handles and latch channels. 3 Tier (60") WITH 2 Point Latch 20 6407V 335.50 Frm. 39.0 LPP 20 6409V 345.00 Frm. 43.5 LPP 20 6411V 356.30 Frm. 48.0 LPP 3 Tier (72") WITH 2 Point Latch 24 6419V 354.05 Frm. 51.0 LPP 24 6421V 361.75 Frm. 57.0 LPP 24 6423V 373.75 Frm. 60.0 LPP 3 Tier Box Locker (37") 6044V 3.80 Frm. 28.0 LPP 6045V 198.60 Frm. 29.0 LPP 6046V 213.75 Frm. 30.0 LPP 3 Tier Box Locker (60") NOTE: Vanguard box lockers have friction catch door pulls. 9 20 6301V 271.95 Frm. 36.0 LPP 9 20 6303V 281.10 Frm. 39.0 LPP 9 20 6305V 292.40 Frm. 39.0 LPP 20 6307V 284.20 Frm. 42.0 LPP 20 6309V 293.70 Frm. 45.0 LPP 20 6311V 305.05 Frm. 48.0 LPP 21 20 6349V 319.75 Frm. 51.0 LPP 3 Tier Box Locker (72") 9 24 6313V 257.75 Frm. 42.0 LPP 9 24 63V 265.35 Frm. 45.0 LPP 9 24 6317V 276. Frm. 48.0 LPP 24 6319V 282.75 Frm. 48.0 LPP 24 6321V 290.40 Frm. 54.0 LPP 24 6323V 302.40 Frm. 57.0 LPP 21 24 6399V 317.35 Frm. 60.0 LPP 24 6372V 309.65 Frm. 63.0 LPP 24 6394V 317.30 Frm. 66.0 LPP 24 6396V 330.65 Frm. 69.0 LPP 24 6300V 338.65 Frm. 74.0 LPP 24 6336V 346.25 Frm. 78.0 LPP 24 6335V 361.05 Frm. 81.0 LPP 4 Tier Box Locker (60") 6325V 248.45 Frm. 44.0 LPP 6327V 255.80 Frm. 48.0 LPP 6329V 267.25 Frm. 52.0 LPP 21 6393V 280.75 Frm. 56.0 LPP 6333V 287.65 Frm. 52.0 LPP 4 Tier Box Locker (72") 6331V 284.95 Frm. 56.0 LPP 6337V 295.95 Frm. 64.0 LPP 6339V 314.05 Frm. 68.0 LPP 21 6395V 331.20 Frm. 72.0 LPP 6431V 331.20 Frm. 68.0 LPP 6433V 352.05 Frm. 72.0 LPP 5 Tier Box Locker (60") 6343V 269.95 Frm. 45.0 LPP 6345V 274. Frm. 50.0 LPP 6347V 293.85 Frm. 55.0 LPP 6351V 310.20 Frm. 55.0 LPP 6397V 324.55 Frm. 60.0 LPP 5 Tier Box Locker (72") 14-2/5 6353V 3.10 Frm. 55.0 LPP 14-2/5 6355V 317.45 Frm. 60.0 LPP 14-2/5 6357V 329.85 Frm. 65.0 LPP 21 14-2/5 6435V 345.50 Frm. 70.0 LPP 14-2/5 6359V 329.85 Frm. 65.0 LPP 14-2/5 6361V 343.65 Frm. 70.0 LPP 6 Tier Box Locker (72") 6365V 3.20 Frm. 54.0 LPP 6367V 323.85 Frm. 60.0 LPP 6369V 340.65 Frm. 66.0 LPP 21 6371V 358.95 Frm. 72.0 LPP 6363V 323.85 Frm. 66.0 LPP 6373V 346.35 Frm. 72.0 LPP 6375V 370.35 Frm. 78.0 LPP 21 6377V 393.45 Frm. 84.0 LPP 6379V 399.85 Frm. 84.0 LPP 21 6378V 429.05 Frm. 90.0 LPP 8 Tier Box Locker (72") 9 6070V 4.60 Frm. 70.0 LPP 9 Tier Box Locker (72") 8 6071V 455.80 Frm. 74.0 LPP Two Person Upper compartment doors are 16 GA. Lower compartment doors are GA. Order 2 locks per frame (1-RH & 1-LH) when locks are required. 60 V 6510V 431.70 Frm. 72.0 LPP 60 V 6506V 434.00 Frm. 76.0 LPP 60 V 6437V 460.95 Frm. 81.0 LPP 72 V 6500V 453.45 Frm. 80.0 LPP 72 V 6501V 463.85 Frm. 74.0 LPP 72 V 6503V 498. Frm. 78.0 LPP 21 72 V 6505V 527.10 Frm. 81.0 LPP 72 V 6509V 526.25 Frm. 95.0 LPP 72 V 65V 550.60 Frm. 100.0 LPP 21 72 V 6525V 594.20 Frm. 105.0 LPP Duplex Doors are Ga. Order 2 locks per frame (1-RH & 1-LH) when locks are required. 60 VX 6519V 4.80 Frm. 74.0 LPP 60 VX 6521V 435.65 Frm. 78.0 LPP 72 VX 6531V 444.90 Frm. 80.0 LPP 72 VX 6533V 476.40 Frm. 84.0 LPP 21 72 VX 6535V 503.10 Frm. 89.0 LPP 6 Penco Products Inc.

Vanguard Bulk Pack Lockers / Recessed Handle Vanguard 7 Person Always ordered as units. Doors are 16 GA. Contains 7 hat compartments with friction catches and one coat compartment with Vanguard Handle. 36 72 6573V 826.05 Unit 167.0 LPP 36 21 72 6575V 863.45 Unit 174.0 LPP 8 Person Always ordered as units. Doors are 16 GA. Contains 8 hat compartments " x " x " with friction catches and 2 coat compartments " x " x 60" with Vanguard Handles. 54 72 6577V 24.50 Unit 249.0 LPP Box Over Locker This is a 72" door frame with a 60" high standard Vanguard door at the bottom, and a box locker at the top. It is the same as is used in 7 and 8 person lockers. " wide top doors are ga. " wide top doors are 16 ga. A shelf is NOT included in the lower compartment: if required, please order separately. 60/72 6439V 307.95 Frm. 52.0 LPP 60/72 6441V 319.80 Frm. 54.0 LPP 60/72 6443V 336.45 Frm. 57.0 LPP 60/72 6436V 347.50 Frm. 63.0 LPP 60/72 6445V 398.35 Frm. 76.0 LPP 21 60/72 6447V 414.55 Frm. 81.0 LPP 16 Person Always ordered as units. GA doors. 69 72 X 6579V 1107.25 Unit 2.0 LPP Wall Mount Locker Height shown is body height including top and bottom door frames. One frame of four "D x "H (nominal) openings side by side with total overall width of 45". Includes brackets and coat rod to mount beneath body. Flat top, no legs only. Ships in 2 cartons. 45 13-5/8 68242 450. Unit 43.0 LPP Continuous Hinge Option for Production KD Lockers - Welded to door, riveted to frame - The charge to replace standard 5-knuckle hinges with a continuous hinge on production 1, 2 or 3-tier lockers is listed below by tier and overall frame height. The order must clearly specify "c-hinge" for each locker requiring this option. This applies to Vanguard, Recessed Vanguard, Guardian, Guardian Medallion, Guardian Plus and Invincible II lockers. Not applicable to Defiant II lockers because they already include continuous hinges. Tier Overall Frame Height Price per Frame 1 72 $14.00 1 60.10 1 48 11.75 1 36 9.00 1 30 10.10 2 72 16.00 2 60.20 3 72 20.00 3 60 23.50 Recessed Vanguard Lockers Same construction as Vanguard, except with Classic III Recessed Handle. Recessed Handle Vanguard 1 Tier Half Height (30-1/2", hat shelf NOT included) Half of a 2 Tier locker, with Recessed handle & latch channel. 30-1/2 6137R 145.70 Frm. 22.0 LPP 30-1/2 6139R 149.35 Frm. 25.0 LPP 30-1/2 6147R 2.60 Frm. 28.0 LPP 1 Tier Half Height (36-1/2", hat shelf NOT included) 36-1/2 6107R 9.95 Frm. 26.0 LPP 36-1/2 67R 167.95 Frm. 27.0 LPP 36-1/2 69R 174.50 Frm. 29.0 LPP 1 Tier (48-1/2") 48-1/2 6176R 193.00 Frm. 38.0 LPP 48-1/2 64R 202.65 Frm. 39.0 LPP 48-1/2 67R 214.05 Frm. 40.0 LPP 1 Tier (60") 9 60 6101R 191.35 Frm. 39.0 LPP 9 60 6103R 195.45 Frm. 41.0 LPP 9 60 6105R 205.90 Frm. 44.0 LPP 60 6111R 207.55 Frm. 44.0 LPP 60 6113R 2.95 Frm. 45.0 LPP 60 61R 227.70 Frm. 47.0 LPP 21 60 6117R 242.60 Frm. 53.0 LPP 24 60 61R 258.35 Frm. 55.0 LPP 60 6119R 230.05 Frm. 52.0 LPP 60 61R 232.65 Frm. 54.0 LPP 60 63R 248.75 Frm. 57.0 LPP 21 60 65R 259.20 Frm. 59.0 LPP 24 60 66R 271.25 Frm. 61.0 LPP 60 6100R 253.50 Frm. 52.0 LPP 60 6134R 265.50 Frm. 56.0 LPP 60 6131R 278.05 Frm. 60.0 LPP 21 60 6133R 291.20 Frm. 63.0 LPP 24 60 6135R 305.20 Frm. 66.0 LPP 24 60 6149R 391.70 Frm. 74.0 LPP 24 21 60 68R 401.70 Frm. 77.0 LPP 24 24 60 6160R 4.90 Frm. 80.0 LPP 1 Tier (Double Doors) 24 60 Y 6141R 464.70 Frm. 76.0 LPP 24 21 60 Y 6143R 474.65 Frm. 79.0 LPP 24 24 60 Y 6145R 486.90 Frm. 82.0 LPP 1 Tier (72") 9 72 61R 205.00 Frm. 46.0 LPP 9 72 63R 211.60 Frm. 48.0 LPP 9 72 65R 223. Frm. 51.0 LPP 72 6161R 226.90 Frm. 49.0 LPP 72 6163R 234.75 Frm. 51.0 LPP 72 6165R 247.35 Frm. 55.0 LPP 21 72 6167R 261.65 Frm. 61.0 LPP 24 72 6168R 276.85 Frm. 66.0 LPP 72 6169R 254.80 Frm. 58.0 LPP 72 6171R 256.40 Frm. 62.0 LPP 72 6173R 268.30 Frm. 65.0 LPP 21 72 6175R 281.40 Frm. 69.0 LPP 24 72 6177R 295.35 Frm. 72.0 LPP 72 6110R 261.75 Frm. 69.0 LPP 72 60R 273.70 Frm. 71.0 LPP 72 61R 286.20 Frm. 73.0 LPP 21 72 63R 298.45 Frm. 77.0 LPP 24 72 65R 325.35 Frm. 78.0 LPP Penco Products Inc. 7

Recessed Handle Vanguard Lockers (Continued) 24 72 6196R 419.75 Frm. 88.0 LPP 24 21 72 6198R 433.85 Frm. 91.0 LPP 24 24 72 6199R 457.95 Frm. 94.0 LPP 1 Tier (Double Doors) 24 72 Y 6191R 496.90 Frm. 90.0 LPP 24 21 72 Y 6193R 5.95 Frm. 93.0 LPP 24 24 72 Y 6195R 535.05 Frm. 96.0 LPP 1 Tier (84") 84 6013R 248.10 Frm. 56.0 LPP 84 6014R 257.25 Frm. 58.0 LPP 84 60R 272.60 Frm. 60.0 LPP 84 6016R 280.85 Frm. 65.0 LPP 84 6017R 290.35 Frm. 67.0 LPP 84 60R 297.75 Frm. 70.0 LPP 2 Tier (48.5") 24 6019R 237.30 Frm. 40.0 LPP 2 Tier (60") 9 30 6201R 2.70 Frm. 36.0 LPP 9 30 6203R 226.85 Frm. 40.0 LPP 9 30 6205R 238.55 Frm. 42.0 LPP 30 6211R 264.30 Frm. 45.0 LPP 30 6213R 270. Frm. 48.0 LPP 30 62R 276.00 Frm. 54.0 LPP 21 30 6217R 287.35 Frm. 60.0 LPP 24 30 6200R 282.05 Frm. 66.0 LPP 30 6227R 287.95 Frm. 54.0 LPP 30 6229R 295.50 Frm. 58.0 LPP 30 6237R 301.80 Frm. 60.0 LPP 21 30 6257R 316.00 Frm. 62.0 LPP 2 Tier (72") 9 36 6221R 239.30 Frm. 44.0 LPP 9 36 6223R 246.50 Frm. 46.0 LPP 9 36 6225R 255.20 Frm. 52.0 LPP 36 6231R 277.30 Frm. 50.0 LPP 36 6233R 289.10 Frm. 52.0 LPP 36 6235R 300.00 Frm. 56.0 LPP 21 36 62R 305.70 Frm. 64.0 LPP 24 36 6220R 320.30 Frm. 72.0 LPP 36 6239R 303.90 Frm. 59.0 LPP 36 6241R 308.60 Frm. 60.0 LPP 36 6243R 322.10 Frm. 68.0 LPP 21 36 6245R 336.20 Frm. 74.0 LPP 24 36 6246R 349.00 Frm. 84.0 LPP 36 6219R 327.00 Frm. 70.0 LPP 36 6259R 341.30 Frm. 74.0 LPP 36 6247R 356.20 Frm. 78.0 LPP 21 36 6249R 371.75 Frm. 84.0 LPP 24 36 6250R 381.70 Frm. 90.0 LPP 24 24 36 6274R 514.25 Frm. 96.0 LPP 2 Tier (84") 42 6251R 280.65 Frm. 56.0 LPP 42 6253R 292.75 Frm. 60.0 LPP 42 6255R 305.85 Frm. 64.0 LPP 42 6073R 307. Frm. 65.0 LPP 42 6261R 320. Frm. 68.0 LPP 42 6263R 333.40 Frm. 72.0 LPP 3 Tier (60") 9 20 6401R 316.95 Frm. 36.0 LPP 9 20 6403R 324.25 Frm. 39.0 LPP 9 20 6405R 331.35 Frm. 39.0 LPP 20 6407R 335.50 Frm. 39.0 LPP 20 6409R 345.00 Frm. 43.5 LPP 20 6411R 356.30 Frm. 48.0 LPP 21 20 6449R 371.00 Frm. 51.0 LPP 3 Tier (72") 9 24 6413R 300.85 Frm. 42.0 LPP 9 24 64R 3.20 Frm. 45.0 LPP 9 24 6417R 324.25 Frm. 48.0 LPP 24 6419R 354.05 Frm. 51.0 LPP 24 6421R 361.75 Frm. 57.0 LPP 24 6423R 373.75 Frm. 60.0 LPP 21 24 6499R 388.70 Frm. 66.0 LPP 24 6472R 381.00 Frm. 66.0 LPP 24 6494R 388.65 Frm. 69.0 LPP 24 6496R 402.00 Frm. 72.0 LPP Two Person Upper compartment doors are 16 GA. Lower compartment doors are GA. Order 2 locks per frame (1-RH & 1-LH) when locks are required. 60 V 6510R 431.70 Frm. 72.0 LPP 60 V 6506R 434.00 Frm. 76.0 LPP 60 V 6437R 460.95 Frm. 81.0 LPP 72 V 6500R 453.45 Frm. 80.0 LPP 72 V 6501R 463.85 Frm. 74.0 LPP 72 V 6503R 498. Frm. 78.0 LPP 21 72 V 6505R 527.10 Frm. 81.0 LPP 72 V 6509R 526.25 Frm. 95.0 LPP 72 V 65R 550.60 Frm. 100.0 LPP 21 72 V 6525R 594.20 Frm. 105.0 LPP Duplex Doors are Ga. Order 2 locks per frame (1-RH & 1-LH) when locks are required. 60 VX 6519R 4.80 Frm. 74.0 LPP 60 VX 6521R 435.65 Frm. 78.0 LPP 72 VX 6531R 444.90 Frm. 80.0 LPP 72 VX 6533R 476.40 Frm. 84.0 LPP 21 72 VX 6535R 503.10 Frm. 89.0 LPP 7 Person Always ordered as a unit. Doors are 16 GA. Contains 7 box locker openings with friction catches and one coat compartment with recessed handle. 36 72 6573R 826.05 Unit 167.0 LPP 36 21 72 6575R 863.45 Unit 174.0 LPP 8 Person Always ordered as a unit. Doors are 16 GA. Contains 8 box locker openings " x " x " with friction catches and 2 coat compartments " x " x 60" with recessed handles. 54 72 6577R 24.50 Unit 249.0 LPP Box Over Locker This is a 72" door frame with a 60" high standard Vanguard door at the bottom, and a box locker at the top. It is the same as is used in 7 and 8 person lockers." wide top doors are ga. " wide top doors are 16 ga. 60/72 6439R 307.95 Frm. 52.0 LPP 60/72 6441R 319.80 Frm. 54.0 LPP 60/72 6443R 336.45 Frm. 57.0 LPP 60/72 6445R 398.35 Frm. 76.0 LPP 21 60/72 6447R 414.55 Frm. 81.0 LPP 8 Penco Products Inc.

Guardian Lockers Guardian lockers: KD construction with 16 GA. doors and 24 GA. body parts. Classic III stainless steel recessed handles. Number plates positioned at top center of door only. Solid door front with air slots in top and bottom door flanges. NOTE: Only lockers 48-1/2" high and taller include a hat shelf. 30-1/2" and 36-1/2" high lockers are not pre-punched to accept shelves. Guardian Lockers 1 Tier (36-1/2", hat shelf NOT included) 36-1/2 6107G 9.95 Frm. 26.0 LPP 36-1/2 67G 167.95 Frm. 27.0 LPP 36-1/2 69G 174.50 Frm. 29.0 LPP 1 Tier (48-1/2") 48-1/2 6176G 193.00 Frm. 38.0 LPP 48-1/2 64G 202.65 Frm. 39.0 LPP 48-1/2 67G 214.05 Frm. 40.0 LPP 1 Tier (60") 9 60 6101G 191.35 Frm. 39.0 LPP 9 60 6103G 195.45 Frm. 41.0 LPP 9 60 6105G 205.90 Frm. 44.0 LPP 60 6111G 207.55 Frm. 44.0 LPP 60 6113G 2.95 Frm. 45.0 LPP 60 61G 227.70 Frm. 47.0 LPP 21 60 6117G 242.60 Frm. 53.0 LPP 24 60 6144G 258.35 Frm. 55.0 LPP 60 6119G 230.05 Frm. 52.0 LPP 60 61G 232.65 Frm. 54.0 LPP 60 63G 248.75 Frm. 57.0 LPP 21 60 65G 259.20 Frm. 59.0 LPP 60 6100G 253.50 Frm. 52.0 LPP 60 6149G 265.50 Frm. 56.0 LPP 60 6131G 278.05 Frm. 60.0 LPP 21 60 6133G 291.20 Frm. 63.0 LPP 24 60 6135G 305.20 Frm. 66.0 LPP 1 Tier (72") 9 72 61G 205.00 Frm. 46.0 LPP 9 72 63G 211.60 Frm. 48.0 LPP 9 72 65G 223. Frm. 51.0 LPP 72 6161G 226.90 Frm. 49.0 LPP 72 6163G 234.75 Frm. 51.0 LPP 72 6165G 247.35 Frm. 55.0 LPP 21 72 6167G 261.65 Frm. 61.0 LPP 24 72 6168G 276.85 Frm. 66.0 LPP 72 6169G 254.80 Frm. 58.0 LPP 72 6171G 256.40 Frm. 62.0 LPP 72 6173G 268.30 Frm. 65.0 LPP 21 72 6175G 281.40 Frm. 69.0 LPP 72 6219G 261.75 Frm. 69.0 LPP 72 6179G 273.70 Frm. 71.0 LPP 72 61G 286.20 Frm. 73.0 LPP 21 72 63G 298.45 Frm. 77.0 LPP 24 72 65G 325.35 Frm. 78.0 LPP 2 Tier (60") 30 6211G 264.30 Frm. 45.0 LPP 30 6213G 270. Frm. 48.0 LPP 30 62G 276.00 Frm. 54.0 LPP 21 30 6217G 287.35 Frm. 60.0 LPP 30 6227G 287.95 Frm. 54.0 LPP 30 6229G 295.50 Frm. 58.0 LPP 30 6237G 301.80 Frm. 60.0 LPP 21 30 6257G 316.00 Frm. 62.0 LPP 30 6279G 323.25 Frm. 60.0 LPP 30 6281G 330.10 Frm. 64.5 LPP 21 30 6283G 337.20 Frm. 69.0 LPP 2 Tier (72") 36 6231G 277.30 Frm. 50.0 LPP 36 6233G 289.10 Frm. 52.0 LPP 36 6235G 300.00 Frm. 56.0 LPP 21 36 62G 305.70 Frm. 64.0 LPP 24 36 6220G 320.30 Frm. 72.0 LPP 36 6239G 303.90 Frm. 59.0 LPP 36 6241G 308.60 Frm. 60.0 LPP 36 6243G 322.10 Frm. 68.0 LPP 21 36 6245G 336.20 Frm. 74.0 LPP 24 36 6246G 349.00 Frm. 84.0 LPP 36 6027G 327.00 Frm. 70.0 LPP 36 6259G 341.30 Frm. 74.0 LPP 36 6247G 356.20 Frm. 78.0 LPP 21 36 6249G 371.75 Frm. 84.0 LPP 3 Tier (60") 20 6407G 335.50 Frm. 39.0 LPP 20 6409G 345.00 Frm. 43.5 LPP 20 6411G 356.30 Frm. 48.0 LPP 21 20 6449G 371.00 Frm. 51.0 LPP 20 6451G 358.05 Frm. 59.0 LPP 20 6453G 369.40 Frm. 63.0 LPP 21 20 6455G 386.50 Frm. 67.0 LPP 3 Tier (72") 24 6419G 354.05 Frm. 51.0 LPP 24 6421G 361.75 Frm. 57.0 LPP 24 6423G 373.75 Frm. 60.0 LPP 21 24 6499G 388.70 Frm. 66.0 LPP 24 6425G 381.00 Frm. 66.0 LPP 24 6427G 388.65 Frm. 69.0 LPP 24 6429G 402.00 Frm. 72.0 LPP 21 24 6437G 417. Frm. 78.0 LPP Two Person Order 2 locks per frame (1-RH & 1-LH) when locks are required. 72 V 6501G 463.85 Frm. 74.0 LPP 72 V 6503G 498. Frm. 78.0 LPP Duplex Order 2 locks per frame (1-RH & 1-LH) when locks are required. 72 VX 6531G 444.90 Frm. 80.0 LPP 72 VX 6533G 476.40 Frm. 84.0 LPP HEIGHT: Height shown is the nominal opening height for 1, 2, 3, 4, 5, & 6 tier lockers. It represents the overall height of the frame for all others. Height does NOT include the standard 6" legs. Penco Products Inc. 9

Guardian Medallion Lockers Guardian Plus Lockers Guardian lockers with the Medallion Option: Identical to other Guardian lockers except that they have a sound-deadening pan welded to the inside of the doors for quieter operation. Guardian Medallion Lockers 1 Tier (60") 9 60 6101M 205.10 Frm. 42.0 LPP 9 60 6103M 209.20 Frm. 44.0 LPP 9 60 6105M 219.65 Frm. 47.0 LPP 60 6111M 221.30 Frm. 47.0 LPP 60 6113M 229.70 Frm. 48.0 LPP 60 61M 241.45 Frm. 50.0 LPP 21 60 6117M 256.35 Frm. 56.0 LPP 60 6119M 243.80 Frm. 55.0 LPP 60 61M 246.40 Frm. 57.0 LPP 60 63M 262.50 Frm. 60.0 LPP 21 60 65M 272.95 Frm. 62.0 LPP 60 6131M 291.80 Frm. 63.0 LPP 1 Tier (72") 9 72 61M 2.75 Frm. 49.0 LPP 9 72 63M 225.35 Frm. 51.0 LPP 9 72 65M 236.90 Frm. 54.0 LPP 72 6161M 240.65 Frm. 52.0 LPP 72 6163M 248.50 Frm. 54.0 LPP 72 6165M 261.10 Frm. 58.0 LPP 21 72 6167M 275.40 Frm. 64.0 LPP 24 72 6168M 290.60 Frm. 67.0 LPP 72 6169M 268.55 Frm. 60.0 LPP 72 6171M 270. Frm. 65.0 LPP 72 6173M 282.05 Frm. 68.0 LPP 21 72 6175M 295. Frm. 72.0 LPP 72 61M 299.95 Frm. 76.0 LPP 21 72 63M 3.20 Frm. 80.0 LPP 24 72 65M 339.10 Frm. 81.0 LPP 2 Tier (60") 30 6211M 281.60 Frm. 47.0 LPP 30 6213M 287.45 Frm. 50.0 LPP 30 62M 293.30 Frm. 56.0 LPP 21 30 6217M 304.65 Frm. 62.0 LPP 2 Tier (72") 36 6231M 294.60 Frm. 53.0 LPP 36 6233M 306.40 Frm. 55.0 LPP 36 6235M 317.30 Frm. 58.0 LPP 21 36 62M 323.00 Frm. 66.0 LPP 24 36 6220M 337.60 Frm. 74.0 LPP 36 6239M 321.20 Frm. 61.0 LPP 36 6241M 325.90 Frm. 62.0 LPP 36 6243M 339.40 Frm. 70.0 LPP 21 36 6245M 353.50 Frm. 76.0 LPP 24 36 6246M 366.30 Frm. 86.0 LPP 3 Tier (72") 24 6419M 376.10 Frm. 54.0 LPP 24 6421M 383.80 Frm. 60.0 LPP 24 6423M 395.80 Frm. 63.0 LPP 21 24 6499M 410.75 Frm. 69.0 LPP Two Person Order 2 locks per frame (1-RH & 1-LH) when locks are required. 72 V 6501M 491.35 Frm. 77.0 LPP 72 V 6503M 525.65 Frm. 81.0 LPP Guardian "Plus" lockers: Identical to standard Guardian lockers, except that the doors are 14 gauge steel. Guardian Plus Lockers 1 Tier (36-1/2", hat shelf NOT included) 36-1/2 6C107 191.50 Frm. 31.8 LPP 36-1/2 6C7 201.10 Frm. 33.4 LPP 36-1/2 6C9 211.20 Frm. 35.2 LPP 1 Tier (48-1/2") 48-1/2 6C176 232.40 Frm. 40.0 LPP 48-1/2 6C4 243.70 Frm. 41.3 LPP 48-1/2 6C7 255. Frm. 43.2 LPP 1 Tier (60") 9 60 6C101 219.05 Frm. 44.0 LPP 9 60 6C103 223.05 Frm. 46.0 LPP 9 60 6C105 236.60 Frm. 49.0 LPP 60 6C111 248.00 Frm. 48.0 LPP 60 6C113 256.60 Frm. 49.0 LPP 60 6C1 265. Frm. 51.0 LPP 21 60 6C117 282.45 Frm. 57.0 LPP 24 60 6C144 300.75 Frm. 63.0 LPP 60 6C119 269.45 Frm. 57.0 LPP 60 6C1 271.65 Frm. 59.0 LPP 60 6C3 280.25 Frm. 62.0 LPP 21 60 6C5 295.40 Frm. 64.0 LPP 60 6C100 286.00 Frm. 59.0 LPP 60 6C149 298.00 Frm. 62.0 LPP 60 6C131 310.50 Frm. 65.0 LPP 21 60 6C133 323.40 Frm. 68.0 LPP 24 60 6C135 337.85 Frm. 71.2 LPP 1 Tier (72") 9 72 6C1 234.65 Frm. 51.0 LPP 9 72 6C3 242.40 Frm. 54.0 LPP 9 72 6C5 254.25 Frm. 57.0 LPP 72 6C161 258.70 Frm. 55.0 LPP 72 6C163 269.45 Frm. 57.0 LPP 72 6C165 277.95 Frm. 60.0 LPP 21 72 6C167 297.55 Frm. 66.0 LPP 24 72 6C168 3.40 Frm. 72.0 LPP 72 6C169 295.40 Frm. 66.0 LPP 72 6C171 297.55 Frm. 68.0 LPP 72 6C173 306. Frm. 71.0 LPP 21 72 6C175 321. Frm. 75.0 LPP 72 6C219 305.65 Frm. 72.0 LPP 72 6C179 319.55 Frm. 76.0 LPP 72 6C1 334.05 Frm. 80.0 LPP 21 72 6C3 349.40 Frm. 84.0 LPP 24 72 6C5 364.95 Frm. 88.2 LPP 2 Tier (60") 30 6C211 291.10 Frm. 50.0 LPP 30 6C213 299.80 Frm. 53.0 LPP 30 6C2 308.40 Frm. 59.0 LPP 21 30 6C217 319.00 Frm. 65.0 LPP 30 6C227 310.55 Frm. 58.0 LPP 30 6C229 3.70 Frm. 62.0 LPP 30 6C237 323.40 Frm. 64.0 LPP 21 30 6C257 336.35 Frm. 68.0 LPP 30 6C279 362.35 Frm. 64.0 LPP 30 6C281 370.10 Frm. 67.5 LPP 21 30 6C283 377.95 Frm. 71.5 LPP 10 Penco Products Inc.

Guardian Plus Lockers (continued) 2 Tier (72") 36 6C231 304.35 Frm. 56.0 LPP 36 6C233 3.85 Frm. 58.0 LPP 36 6C235 331.20 Frm. 62.0 LPP 21 36 6C2 336. Frm. 70.0 LPP 36 6C239 336.25 Frm. 65.0 LPP 36 6C241 338.90 Frm. 69.0 LPP 36 6C243 353.45 Frm. 72.0 LPP 21 36 6C245 368.30 Frm. 79.0 LPP 36 6C027 351.75 Frm. 74.0 LPP 36 6C259 367.00 Frm. 80.0 LPP 36 6C247 382.95 Frm. 86.0 LPP 21 36 6C249 399.65 Frm. 92.0 LPP 3 Tier (60") 20 6C407 378.70 Frm. 51.0 LPP 20 6C409 388.05 Frm. 54.0 LPP 20 6C411 398.10 Frm. 57.0 LPP 21 20 6C449 406.65 Frm. 60.0 LPP 3 Tier (72") 24 6C419 389.30 Frm. 57.0 LPP 24 6C421 396.65 Frm. 63.0 LPP 24 6C423 409.05 Frm. 66.0 LPP 21 24 6C499 416.50 Frm. 72.0 LPP 24 6C425 410.25 Frm. 69.0 LPP 24 6C427 413.25 Frm. 75.0 LPP 24 6C429 426.20 Frm. 78.0 LPP 21 24 6C437 448.35 Frm. 84.0 LPP Cremone Handle Option Cremone handles are available on standard Guardian Plus 1, 2 & 3 tier multi-point latch lockers over 9 wide. For the cremone handle option, add the following to the price of the corresponding Guardian Plus locker: 1 Tier - $65 per frame 2 Tier - $135 per frame 3 Tier - $205 per frame Continuous Hinge Option for Production KD Lockers - Welded to door, riveted to frame - The charge to replace standard 5-knuckle hinges with a continuous hinge on production 1, 2 or 3-tier lockers is listed below by tier and overall frame height. The order must clearly specify "c-hinge" for each locker requiring this option. This applies to Vanguard, Recessed Vanguard, Guardian, Guardian Medallion, Guardian Plus and Invincible II lockers. Not applicable to Defiant II lockers because they already include continuous hinges. Tier Overall Frame Height Price per Frame 1 72 $14.00 1 60.10 1 48 11.75 1 36 9.00 1 30 10.10 2 72 16.00 2 60.20 3 72 20.00 3 60 23.50 HEIGHT: Height shown is the nominal opening height for 1, 2, 3, 4, 5, & 6 tier lockers. It represents the overall height of the frame for all others. Height does NOT include the standard 6" legs. Penco Products Inc. 11

Guardian "Defiant II" Lockers (1, 2 & 3 tier): Same as standard Guardian, except that the door is solid 14 GA. with single point latch construction. No latch channel or moving parts in the door. Doors have a full height vertical pan welded to top, bottom and hinge-side flanges as well as to the 14 ga. door skin for extra stiffness (doors wider than have a horizontal pan). Available only with continuous hinge. Stainless steel recessed pocket with an integral door pull. Number plate positioned at top center of door only. Guardian Defiant II Lockers 1 Tier (36-1/2", hat shelf NOT included) 36-1/2 6E107 193.75 Frm. 33.0 LPP 36-1/2 6E7 203.45 Frm. 35.7 LPP 36-1/2 6E9 213.60 Frm. 37.0 LPP 1 Tier (48-1/2") 48-1/2 6E176 236.00 Frm. 41.9 LPP 48-1/2 6E4 247.85 Frm. 43.7 LPP 48-1/2 6E7 260.20 Frm. 45.1 LPP 1 Tier (60") 60 6E111 248.20 Frm. 50.0 LPP 60 6E113 258.00 Frm. 51.0 LPP 60 6E1 265.85 Frm. 53.0 LPP 21 60 6E117 283.45 Frm. 60.0 LPP 60 6E119 269.95 Frm. 59.0 LPP 60 6E1 271.80 Frm. 61.0 LPP 60 6E3 281.55 Frm. 65.0 LPP 21 60 6E5 297. Frm. 67.0 LPP 60 6E100 285.60 Frm. 62.0 LPP 60 6E149 298.00 Frm. 65.0 LPP 60 6E131 310.85 Frm. 68.0 LPP 21 60 6E133 324.55 Frm. 71.0 LPP 24 60 6E135 353.95 Frm. 73.0 LPP 1 Tier (72") 72 6E161 260.10 Frm. 57.0 LPP 72 6E163 269.95 Frm. 59.0 LPP 72 6E165 279.55 Frm. 62.0 LPP 21 72 6E167 299.20 Frm. 69.0 LPP 24 72 6E168 3.85 Frm. 75.0 LPP 72 6E169 297. Frm. 68.0 LPP 72 6E171 299.20 Frm. 70.0 LPP 72 6E173 306.95 Frm. 73.0 LPP 21 72 6E175 322.60 Frm. 78.0 LPP 72 6E219 305.40 Frm. 70.0 LPP 72 6E179 319.60 Frm. 77.0 LPP 72 6E1 334.45 Frm. 82.0 LPP 21 72 6E3 350.10 Frm. 87.0 LPP 24 72 6E5 379.35 Frm. 90.0 LPP Guardian Defiant II Lockers 2 Tier (60") 30 6E211 293.30 Frm. 52.0 LPP 30 6E213 301.20 Frm. 55.0 LPP 30 6E2 309.00 Frm. 61.0 LPP 21 30 6E217 320.65 Frm. 67.0 LPP 30 6E227 3.80 Frm. 60.0 LPP 30 6E229 316.75 Frm. 64.0 LPP 30 6E237 324.55 Frm. 66.0 LPP 21 30 6E257 340.25 Frm. 70.0 LPP 30 6E279 342.70 Frm. 75.0 LPP 30 6E281 357.70 Frm. 84.0 LPP 21 30 6E283 375.80 Frm. 91.0 LPP 24 30 6E285 404.25 Frm. 98.0 LPP 2 Tier (72") 36 6E231 305.10 Frm. 60.0 LPP 36 6E233 321.30 Frm. 62.0 LPP 36 6E235 333.70 Frm. 68.0 LPP 21 36 6E2 338.65 Frm. 78.0 LPP 24 36 6E220 344. Frm. 80.0 LPP 36 6E239 336.35 Frm. 70.0 LPP 36 6E241 340.25 Frm. 72.0 LPP 36 6E243 355.35 Frm. 78.0 LPP 21 36 6E245 370.85 Frm. 85.0 LPP 36 6E027 363.50 Frm. 80.0 LPP 36 6E259 373.00 Frm. 88.0 LPP 36 6E247 391.05 Frm. 94.0 LPP 21 36 6E249 410.65 Frm. 100.0 LPP 24 36 6E250 441.85 Frm. 108.0 LPP 3 Tier (60") 20 6E407 381.90 Frm. 54.0 LPP 20 6E409 388.10 Frm. 57.0 LPP 20 6E411 400.45 Frm. 60.0 LPP 21 20 6E449 407.85 Frm. 63.0 LPP 20 6E451 391.75 Frm. 67.0 LPP 20 6E453 402.90 Frm. 72.0 LPP 21 20 6E455 411.50 Frm. 76.0 LPP 3 Tier (72") 24 6E419 390.50 Frm. 60.0 LPP 24 6E421 398.00 Frm. 66.0 LPP 24 6E423 411.50 Frm. 69.0 LPP 21 24 6E499 420.20 Frm. 73.0 LPP 24 6E425 4.80 Frm. 72.0 LPP 24 6E427 419.40 Frm. 78.0 LPP 24 6E429 430.65 Frm. 81.0 LPP 21 24 6E437 448.20 Frm. 87.0 LPP Rotary Locks Rotary or wrap-around style built-in locks cannot be used on a standard Defiant II locker latch. For these applications, specify the Defiant II-R option that includes a special hasp and a pocket with no padlock slot. There is no charge for this option but it must be clearly called out on the purchase order or estimate sheet and may add to the order lead time. Specifying the lock that will be used is required whether the locks are ordered from Penco or directly from the lock manufacturer. Lockers equipped with this option are configured for use ONLY with a rotary style lock. Locks must be ordered separately. HEIGHT: Height shown is the nominal opening height for 1, 2, 3, 4, 5, & 6 tier lockers. It represents the overall height of the frame for all others. Height does NOT include the standard 6" legs. Penco Products Inc.

Invincible II Lockers Invincible II lockers: KD construction, 14 ga. doors, 16 GA. body and GA. back. Diamondshaped perforations are standard on doors and sides. Classic III stainless steel recessed handle on doors 20" or higher, with number plate at top of door. Box locker doors have padlock staple and door pull with number plate on the door. To delete perforations, or to add mini-louvers see page 32. See "Ordering Information" on Invincible II lockers for details on required group ends. NOTE: Only lockers 48-1/2" high and taller include a hat shelf. 30-1/2" and 36-1/2" high lockers are not pre-punched to accept shelves. Note that Invincible II Lockers are ordered differently than other lockers. 1. Basic units: Note that a single frame of a Basic Unit has only one side, and is not complete until bolted to another locker or until a Group End has been added. Locate the desired type and size of locker in the pages that follow. Order the desired number of frames of the Basic Units required. 6" high legs are standard, if no legs are required, specify "No Legs" when ordering. 2. Group Ends: To end a group or row of lockers, order either a perforated or solid 16 gauge Group End in the Invincible II Basic Units 1 Tier (36-1/2", hat shelf NOT included) 36-1/2 X 6A011 223.70 Frm. 34.0 LPP 36-1/2 X 6A013 236. Frm. 35.0 LPP 36-1/2 X 6A0 246.30 Frm. 38.0 LPP 1 Tier (48-1/2") 48-1/2 X 6A017 275.05 Frm. 49.0 LPP 48-1/2 X 6A019 290.00 Frm. 50.0 LPP 48-1/2 X 6A021 307.85 Frm. 52.0 LPP 1 Tier (60") 9 60 X 6A101 281.40 Frm. 51.3 LPP 9 60 X 6A103 294.85 Frm. 54.9 LPP 9 60 X 6A105 308.40 Frm. 58.6 LPP 60 X 6A9 316.55 Frm. 58.4 LPP 60 X 6A131 331.95 Frm. 62.5 LPP 60 X 6A135 348.60 Frm. 66.7 LPP 21 60 X 6A133 369.55 Frm. 69.9 LPP 24 60 X 6A137 391.70 Frm. 73.0 LPP 60 X 6A141 333.70 Frm. 71.5 LPP 60 X 6A143 348.90 Frm. 73.0 LPP 60 X 6A145 365.80 Frm. 76.3 LPP 21 60 X 6A147 387.30 Frm. 80.6 LPP 60 X 6A501 390.70 Frm. 71.0 LPP 60 X 6A149 410.65 Frm. 76.0 LPP 60 X 6A1 431.60 Frm. 82.9 LPP 21 60 X 6A3 447.90 Frm. 90.1 LPP 24 60 X 6A5 473.85 Frm. 97.4 LPP 24 60 X 6A117 498.85 Frm. 101.8 LPP 24 21 60 X 6A119 517.40 Frm. 107.8 LPP 24 24 60 X 6A1 537.45 Frm. 113.8 LPP 1 Tier (72") 9 72 X 6A107 297.35 Frm. 58.3 LPP 9 72 X 6A109 3. Frm. 62.3 LPP 9 72 X 6A111 331.00 Frm. 66.3 LPP 72 X 6A7 326.45 Frm. 67.7 LPP 72 X 6A9 343.25 Frm. 71.6 LPP 72 X 6A161 363.60 Frm. 76.5 LPP 21 72 X 6A163 391.05 Frm. 81.5 LPP 24 72 X 6A167 420.35 Frm. 86.5 LPP Invincible II Ordering Information appropriate size (for solid group ends, order one for each end of row). Note that groups of lockers can be built in long rows if built in place, however groups are difficult to move if they exceed 3-wide. Consult an installer. 3. Slope Top: For slope top lockers, accessorize with Slope Hood components. 4. Miscellaneous: Slope top kits, unit slope tops and partitions in this price list cannot be used with Invincible II lockers. Closed Bases can be used with lockers that have legs. 72 X 6A165 363. Frm. 74.9 LPP 72 X 6A169 377.35 Frm. 80.7 LPP 72 X 6A171 396.60 Frm. 86.1 LPP 21 72 X 6A173 423.40 Frm. 91.0 LPP 24 72 X 6A172 449.80 Frm. 96.0 LPP 72 X 6A500 413.70 Frm. 81.0 LPP 72 X 6A175 431.30 Frm. 87.2 LPP 72 X 6A177 449.65 Frm. 94.3 LPP 21 72 X 6A179 476.35 Frm. 101.8 LPP 24 72 X 6A1 503.85 Frm. 109.9 LPP 24 72 X 6A2 527.95 Frm. 110.0 LPP 24 72 X 6A3 532.85 Frm. 1.2 LPP 24 21 72 X 6A5 558.55 Frm. 1.2 LPP 24 24 72 X 6A7 588.00 Frm. 3.7 LPP 2 Tier (60") 30 X 6A213 375.85 Frm. 61.6 LPP 30 X 6A2 393.75 Frm. 65.8 LPP 30 X 6A217 4.05 Frm. 70.2 LPP 30 X 6A225 410.65 Frm. 75.4 LPP 30 X 6A239 431.60 Frm. 79.2 LPP Skip 21 30 X 6A241 456. Frm. 83.8 LPP 30 X 6A223 443.45 Frm. 79.0 LPP 30 X 6A227 463.85 Frm. 86.8 LPP 21 30 X 6A229 486. Frm. 94.6 LPP 24 30 X 6A231 5.40 Frm. 103.8 LPP 24 30 X 6A233 538.30 Frm. 107.0 LPP 24 21 30 X 6A235 564.10 Frm. 1.0 LPP 24 24 30 X 6A237 592.40 Frm. 1.8 LPP For Perforated Group Ends or Solid Group Ends for Invincible II Lockers, see Invincible II Section page 14 &. (These are required to end each group of 1 or more lockers). HEIGHT: Height shown is the nominal opening height for 1, 2, 3, 4, 5, & 6 tier lockers. It represents the overall height of the frame for all others. Height does NOT include the standard 6" legs. Penco Products Inc. 13

Invincible II Lockers 2 Tier (72") 36 X 6A245 394.95 Frm. 70.2 LPP 36 X 6A247 4. Frm. 74.6 LPP 36 X 6A249 433.75 Frm. 79.4 LPP 21 36 X 6A251 461.45 Frm. 84.2 LPP 36 X 6A257 439.35 Frm. 84.6 LPP 36 X 6A259 459.60 Frm. 89.4 LPP 21 36 X 6A261 484.60 Frm. 94.2 LPP Skip 24 36 X 6A253 5.25 Frm. 99.0 LPP 36 X 6A508 446.80 Frm. 82.0 LPP 36 X 6A263 468.05 Frm. 89.6 LPP 36 X 6A265 489.80 Frm. 97.6 LPP 21 36 X 6A267 5.85 Frm. 106.0 LPP 24 36 X 6A269 540.80 Frm. 1.6 LPP 24 36 X 6A271 593.90 Frm. 119.8 LPP 24 21 36 X 6A273 603.90 Frm. 6.0 LPP 24 24 36 X 6A275 633. Frm. 132.4 LPP 3 Tier (60") 20 X 6A287 4.50 Frm. 67.5 LPP 20 X 6A289 440.85 Frm. 72.3 LPP 20 X 6A291 464.40 Frm. 77.1 LPP 20 X 6A293 481.00 Frm. 84.0 LPP 20 X 6A295 503.95 Frm. 91.2 LPP 21 20 X 6A297 529.65 Frm. 96.6 LPP 20 X 6A220 546.90 Frm. 106.3 LPP 3 Tier (72") 24 X 6A281 440.85 Frm. 77.7 LPP 24 X 6A283 460.80 Frm. 82.8 LPP 24 X 6A285 481.60 Frm. 87.9 LPP 24 X 6A301 506.75 Frm. 93.6 LPP 24 X 6A303 529. Frm. 99.9 LPP 21 24 X 6A305 555.80 Frm. 105.6 LPP 24 X 6A221 582.60 Frm. 111.3 LPP 4 Tier Box Locker (60") X 6A307 346.00 Frm. 64.0 LPP X 6A309 368.00 Frm. 69.2 LPP X 6A311 390.40 Frm. 74.8 LPP X 6A313 404.60 Frm. 75.6 LPP X 6A3 429.55 Frm. 81.6 LPP 4 Tier Box Locker (72") X 6A319 370.45 Frm. 72.0 LPP X 6A321 392.20 Frm. 77.6 LPP X 6A323 413.45 Frm. 83.6 LPP X 6A331 433.60 Frm. 84.4 LPP X 6A335 455. Frm. 91.2 LPP 5 Tier Box Locker (60") X 6A351 362.25 Frm. 69.0 LPP X 6A353 386.20 Frm. 74.5 LPP X 6A355 409.70 Frm. 80.5 LPP 21 X 6A531 434.55 Frm. 86.6 LPP 24 X 6A532 461.00 Frm. 92.8 LPP X 6A357 407.00 Frm. 85.0 LPP X 6A359 448.85 Frm. 92.5 LPP 21 X 6A361 477.35 Frm. 99.5 LPP 24 X 6A534 507.65 Frm. 106.6 LPP X 6A419 487.45 Frm. 102.5 LPP 21 X 6A421 519.95 Frm. 113.0 LPP HEIGHT: Height shown is the nominal opening height for 1, 2, 3, 4, 5, & 6 tier lockers. It represents the overall height of the frame for all others. Height does NOT include the standard 6" legs. 5 Tier Box Locker (72") 14-2/5 X 6A363 401.30 Frm. 76.0 LPP 14-2/5 X 6A365 423.50 Frm. 82.5 LPP 14-2/5 X 6A367 447.90 Frm. 89.0 LPP 14-2/5 X 6A369 447.05 Frm. 94.0 LPP 14-2/5 X 6A371 486.20 Frm. 101.5 LPP 21 14-2/5 X 6A373 516.00 Frm. 109.0 LPP 14-2/5 X 6A445 529.30 Frm. 113.0 LPP 21 14-2/5 X 6A447 564.80 Frm. 4.0 LPP 6 Tier Box Locker (72") X 6A375 423.40 Frm. 78.6 LPP X 6A377 441.10 Frm. 84.0 LPP X 6A379 455.85 Frm. 86.4 LPP 21 X 6A381 487.40 Frm. 91.2 LPP X 6A383 465.95 Frm. 96.6 LPP X 6A385 494.85 Frm. 105.0 LPP 21 X 6A389 523. Frm. 113.4 LPP 24 X 6A541 553.10 Frm. 1.9 LPP X 6A423 536.55 Frm. 117.0 LPP 21 X 6A425 571.00 Frm. 8.4 LPP Perforated Group Ends, Half Height For 1 Tier, Invincible II Order for each group or end of row. 36-1/2 603600V 50.85 Ea. 5.0 LPP 36-1/2 603602V 67.45 Ea. 6.1 LPP 36-1/2 603604V 75.00 Ea. 7.3 LPP 48-1/2 603606V 56.55 Ea. 6.7 LPP 48-1/2 603608V 63.85 Ea. 8.1 LPP 48-1/2 603700V 74.85 Ea. 9.7 LPP Perforated Group Ends, 1-6 Tier For 1,2,3,4,5 & 6 Tier, Invincible II Order for each group or end of row. 60 602100V 58. Ea. 8.3 LPP 60 602102V 68.80 Ea. 10.3 LPP 60 602104V 80.70 Ea..3 LPP 21 60 602106V 97.10 Ea. 14.1 LPP 24 60 602108V 108.80 Ea. 16.1 LPP 72 602110V 62.50 Ea. 9.9 LPP 72 6021V 76.00 Ea..2 LPP 72 602114V 89.55 Ea. 14.5 LPP 21 72 602116V 105.35 Ea. 16.8 LPP 24 72 6021V 0.35 Ea. 19.1 LPP Solid Group Ends, Half Height For 1 Tier, Invincible II Order for each end of row if both ends are to be solid. 36-1/2 603601S 50.85 Ea. 7.0 LPP 36-1/2 603603S 67.45 Ea. 8.8 LPP 36-1/2 603605S 75.00 Ea. 10.7 LPP 48-1/2 603607S 56.55 Ea. 9.3 LPP 48-1/2 603609S 63.85 Ea. 11.7 LPP 48-1/2 603701S 74.85 Ea. 14.2 LPP Solid Group Ends, 1-6 Tier For 1,2,3,4,5 & 6 Tier, Invincible II Order for each end of row if both ends are to be solid. 60 602101S 58. Ea. 11.5 LPP 60 602103S 68.80 Ea. 14.6 LPP 60 602105S 80.70 Ea. 17.7 LPP 21 60 602107S 97.10 Ea. 20.8 LPP 24 60 602109S 108.80 Ea. 23.9 LPP 72 602111S 62.50 Ea. 13.9 LPP 72 602113S 76.00 Ea. 17.6 LPP 72 6021S 89.55 Ea. 21.3 LPP 21 72 602117S 105.35 Ea. 25.0 LPP 24 72 602119S 0.35 Ea. 28.7 LPP 14 Penco Products Inc.

Invincible II Lockers Invincible II Basic Units 8 Tier Box Locker (72") 9 X 6A393 543.55 Frm. 87.2 LPP 9 X 6A395 573.25 Frm. 95.2 LPP 9 X 6A397 606. Frm. 105.6 LPP 9 X 6A401 646.85 Frm. 107.2 LPP 9 X 6A403 683.55 Frm. 0.0 LPP 21 9 X 6A405 722.70 Frm. 8.0 LPP 9 Tier Box Locker (72") 8 X 6A407 549.05 Frm. 93.6 LPP 8 X 6A409 582.50 Frm. 102.6 LPP 8 X 6A411 6.05 Frm. 111.6 LPP 8 X 6A413 665.10 Frm. 1.2 LPP 8 X 6A4 698.55 Frm. 8.7 LPP 21 8 X 6A417 739.05 Frm. 140.4 LPP Perforated Group Ends, 8-9 Tier For 8 & 9 Tier, Invincible II 72 6020V 86.90 Ea. 9.9 LPP 72 6022V 106.60 Ea..2 LPP 72 6024V 1.80 Ea. 14.5 LPP 21 72 6026V 3.55 Ea. 16.8 LPP Solid Group Ends, 8-9 Tier 72 6021S 86.90 Ea. 13.9 LPP 72 6023S 106.60 Ea. 17.6 LPP 72 6025S 1.80 Ea. 21.3 LPP 21 72 6027S 3.55 Ea. 25.0 LPP Perforated Group Ends or Solid Group Ends for Invincible II Lockers are on page 14 &. (These are required to end each group of 1 or more lockers). Cremone Handle Option Cremone handles are available on standard Invincible II 1, 2 & 3 tier multi-point latch lockers over 9 wide. For the cremone handle option, add the following to the price of the corresponding Invincible II locker: 1 Tier - $65 per frame (Assumes a single door on 24 wide models) 2 Tier - $135 per frame 3 Tier - $205 per frame Continuous Hinge Option for Production KD Lockers - Welded to door, riveted to frame - The charge to replace standard 5-knuckle hinges with a continuous hinge on production 1, 2 or 3-tier lockers is listed below by tier and overall frame height. The order must clearly specify "c-hinge" for each locker requiring this option. This applies to Vanguard, Recessed Vanguard, Guardian, Guardian Medallion, Guardian Plus and Invincible II lockers. Not applicable to Defiant II lockers because they already include continuous hinges. Tier Overall Frame Height Price per Frame 1 72 $14.00 1 60.10 1 48 11.75 1 36 9.00 1 30 10.10 2 72 16.00 2 60.20 3 72 20.00 3 60 23.50 HEIGHT: Height shown is the nominal opening height for 1, 2, 3, 4, 5, & 6 tier lockers. It represents the overall height of the frame for all others. Height does NOT include the standard 6" legs. Penco Products Inc.

Invincible II Defiant II Lockers Invincible II "Defiant II" (1, 2, 3 tier only): Same as Invincible II, except that the 14 GA. door has single point latch construction. No latch channel or moving parts in the door. Doors have a full height vertical pan welded to top, bottom and hinge-side flanges as well as to the 14 GA. door skin for extra stiffness (doors wider than have a horizontal pan). Available only with continuous hinge. Stainless steel recessed pocket with an integral door pull and number plate at top of door. Air slots in top and bottom flanges of door. Invincible II Defiant II Basic Units 1 Tier (36-1/2", hat shelf NOT included) 36-1/2 X 6P011 226.25 Frm. 36.0 LPP 36-1/2 X 6P013 238.75 Frm. 37.0 LPP 36-1/2 X 6P0 249.05 Frm. 40.0 LPP 1 Tier (48-1/2") 48-1/2 X 6P017 278.65 Frm. 51.0 LPP 48-1/2 X 6P019 294.25 Frm. 52.0 LPP 48-1/2 X 6P021 311.70 Frm. 54.0 LPP 1 Tier (60") 60 X 6P9 3.80 Frm. 62.5 LPP 60 X 6P131 334.45 Frm. 66.9 LPP 60 X 6P135 351.95 Frm. 71.6 LPP 60 X 6P143 351.95 Frm. 76.0 LPP 60 X 6P145 369.55 Frm. 81.2 LPP 21 60 X 6P147 391.05 Frm. 85.9 LPP 60 X 6P501 395.90 Frm. 73.1 LPP 60 X 6P149 414.60 Frm. 80.4 LPP 60 X 6P1 434.10 Frm. 87.8 LPP 21 60 X 6P3 451.70 Frm. 95.6 LPP 24 60 X 6P5 477.00 Frm. 103.1 LPP 24 60 X 6P117 503.70 Frm. 104.0 LPP 24 21 60 X 6P119 520.95 Frm. 110.0 LPP 24 24 60 X 6P1 543.80 Frm. 116.0 LPP 1 Tier (72") 72 X 6P7 328.35 Frm. 72.2 LPP 72 X 6P9 346.10 Frm. 76.5 LPP 72 X 6P161 365.65 Frm. 81.4 LPP 72 X 6P169 381.30 Frm. 85.6 LPP 72 X 6P171 398.85 Frm. 91.5 LPP 21 72 X 6P173 426.25 Frm. 96.8 LPP 24 72 X 6P172 454.35 Frm. 102.0 LPP 72 X 6P500 417.20 Frm. 85.6 LPP 72 X 6P175 434.10 Frm. 92.4 LPP 72 X 6P177 451.70 Frm. 99.7 LPP 21 72 X 6P179 479.05 Frm. 107.6 LPP 24 72 X 6P1 506.40 Frm. 116.1 LPP 24 72 X 6P3 537.25 Frm. 3.0 LPP 24 21 72 X 6P5 563.40 Frm. 6.0 LPP 24 24 72 X 6P7 593.45 Frm. 9.0 LPP 2 Tier (60") 30 X 6P213 383.20 Frm. 67.2 LPP 30 X 6P2 398.85 Frm. 72.2 LPP 30 X 6P217 422.35 Frm. 77.6 LPP 30 X 6P225 4.50 Frm. 81.8 LPP 30 X 6P239 437.90 Frm. 86.6 LPP Skip 21 30 X 6P241 461.45 Frm. 92.0 LPP 30 X 6P223 449.80 Frm. 85.4 LPP 30 X 6P227 469.25 Frm. 94.2 LPP 21 30 X 6P229 492.70 Frm. 102.8 LPP Skip 24 30 X 6P231 520.10 Frm. 1.2 LPP 24 30 X 6P233 545. Frm. 114.0 LPP 24 21 30 X 6P235 571.25 Frm. 0.0 LPP 24 24 30 X 6P237 599.90 Frm. 5.0 LPP 2 Tier (72") 36 X 6P245 402.75 Frm. 76.2 LPP 36 X 6P247 4.50 Frm. 81.6 LPP 36 X 6P249 437.90 Frm. 87.4 LPP 21 36 X 6P251 466.75 Frm. 93.4 LPP 36 X 6P257 445.80 Frm. 91.6 LPP 36 X 6P259 465.35 Frm. 97.4 LPP 21 36 X 6P261 488.90 Frm. 103.2 LPP 24 36 X 6P253 517.05 Frm. 109.4 LPP 36 X 6P263 473. Frm. 97.0 LPP 36 X 6P265 496.65 Frm. 105.6 LPP 21 36 X 6P267 520.10 Frm. 1.0 LPP 24 36 X 6P269 547.45 Frm. 5.2 LPP 24 36 X 6P271 601.45 Frm. 7.0 LPP 24 21 36 X 6P273 610.35 Frm. 133.0 LPP 24 24 36 X 6P275 639.70 Frm. 139.0 LPP 3 Tier (60") 20 X 6P287 425.50 Frm. 69.0 LPP 20 X 6P289 447.90 Frm. 73.8 LPP 20 X 6P291 470.35 Frm. 78.9 LPP 20 X 6P293 487. Frm. 85.5 LPP 20 X 6P295 5.00 Frm. 92.7 LPP 21 20 X 6P297 537.45 Frm. 98.1 LPP 3 Tier (72") 24 X 6P281 447.90 Frm. 80.7 LPP 24 X 6P283 470.35 Frm. 85.8 LPP 24 X 6P285 492.70 Frm. 90.9 LPP 24 X 6P301 5.00 Frm. 96.6 LPP 24 X 6P303 537.45 Frm. 102.9 LPP Skip 21 24 X 6P305 565.55 Frm. 108.6 LPP 24 X 6P221 600.05 Frm. 1.9 LPP 21 24 X 6P519 625.00 Frm. 5.9 LPP 24 24 X 6P520 653.45 Frm. 133.3 LPP For Perforated Group Ends or Solid Group Ends for Invincible II Defiant II Lockers, see Invincible II Section page 14 &. (These are required to end each group of 1 or more lockers). Rotary Locks Rotary or wrap-around style built-in locks cannot be used on a standard Defiant II locker latch. For these applications, specify the Defiant II-R option that includes a special hasp and a pocket with no padlock slot. There is no charge for this option but it must be clearly called out on the purchase order or estimate sheet and may add to the order lead time. Specifying the lock that will be used is required whether the locks are ordered from Penco or directly from the lock manufacturer. Lockers equipped with this option are configured for use ONLY with a rotary style lock. Locks must be ordered separately. 16 Penco Products Inc. HEIGHT: Height shown is the nominal opening height for 1, 2, 3, 4, 5, & 6 tier lockers. It represents the overall height of the frame for all others. Height does NOT include the standard 6" legs.

Stadium Lockers (KD and Welded) Stadium Lockers are open front lockers ideally suited for athletic team room use. They are available in several configurations, from a shell with shelf and coat hanger bar, to a fully outfitted unit complete with shelf, lockable security box and lockable foot locker (locks must be ordered separately). The standard configuration is for the sides (16 GA.) to be perforated with diamond-shaped holes, and for the back ( GA.) to be solid. The top, bottom, front frame and optional shelf are 16 GA. The gauge of the optional foot locker seat and security box door is 14 GA. Stadium Lockers are available in KD construction in 72" height only, and no base or legs are available. In Welded construction, the height is 76" only, which includes a 16 Ga. 4" high integral closed base as standard. All Stadium lockers are ONE WIDE construction. Number plates, hooks, coat rods, door pulls are to be field installed. KD Stadium w/ Perforated Sides NO Base on KD Stadium Lockers. All Stadium Lockers are ONE WIDE. Shell with Shelf 72 X 6KFD01 4.00 Ea. 80.0 LPP 24 72 X 6KFD10 522.25 Ea. 90.0 LPP 24 21 72 X 6KFD20 535.10 Ea. 97.0 LPP 24 24 72 X 6KFD30 576.00 Ea. 104.0 LPP 33 72 X 6KFD40 585.10 Ea. 108.0 LPP 33 21 72 X 6KFD50 637.40 Ea. 116.0 LPP 33 24 72 X 6KFD60 689.10 Ea. 4.0 LPP Shell, Shelf & Security Box 72 X 6KFD09 506.95 Ea. 89.0 LPP 24 72 X 6KFD11 589.50 Ea. 99.0 LPP 24 21 72 X 6KFD21 652.00 Ea. 106.0 LPP 24 24 72 X 6KFD31 750.75 Ea. 113.0 LPP 33 72 X 6KFD41 703.85 Ea. 117.0 LPP 33 21 72 X 6KFD51 751.05 Ea. 5.0 LPP 33 24 72 X 6KFD61 808.90 Ea. 133.0 LPP Shell, Shelf & Foot Locker 72 X 6KFD02 595.40 Ea. 101.0 LPP 24 72 X 6KFD 746.95 Ea. 1.0 LPP 24 21 72 X 6KFD22 753.00 Ea. 2.0 LPP 24 24 72 X 6KFD32 842.95 Ea. 131.0 LPP 33 72 X 6KFD42 848.70 Ea. 139.0 LPP 33 21 72 X 6KFD52 901.65 Ea. 149.0 LPP 33 24 72 X 6KFD62 1003.90 Ea. 160.0 LPP Shell, Shelf, Foot Locker & Security Box 72 X 6KFD03 752.60 Ea. 111.0 LPP 24 72 X 6KFD13 866.70 Ea. 2.0 LPP 24 21 72 X 6KFD23 874.00 Ea. 131.0 LPP 24 24 72 X 6KFD33 947.65 Ea. 140.0 LPP 33 72 X 6KFD43 1136.05 Ea. 148.0 LPP 33 21 72 X 6KFD53 1145.65 Ea. 8.0 LPP 33 24 72 X 6KFD63 17.45 Ea. 169.0 LPP Welded Stadium w/ Perforated Sides Welded Stadium Lockers include integral 4"H base. All Stadium Lockers are ONE WIDE. Shell with Shelf 76 X 6WFD01 744.65 Ea. 87.0 LPP 24 76 X 6WFD10 798.10 Ea. 97.0 LPP 24 21 76 X 6WFD20 837.85 Ea. 106.0 LPP 24 24 76 X 6WFD30 874.35 Ea. 114.0 LPP 33 76 X 6WFD40 806.40 Ea. 1.0 LPP 33 21 76 X 6WFD50 876.90 Ea. 4.0 LPP 33 24 76 X 6WFD60 908. Ea. 133.0 LPP Shell, Shelf & Security Box 76 X 6WFD09 834.80 Ea. 100.0 LPP 24 76 X 6WFD11 881.25 Ea. 1.0 LPP 24 21 76 X 6WFD21 926.95 Ea. 1.0 LPP 24 24 76 X 6WFD31 947.35 Ea. 9.0 LPP 33 76 X 6WFD41 895.55 Ea. 133.0 LPP 33 21 76 X 6WFD51 966.10 Ea. 142.0 LPP 33 24 76 X 6WFD61 986.95 Ea. 1.0 LPP Shell, Shelf & Foot Locker 76 X 6WFD02 935.65 Ea. 114.0 LPP 24 76 X 6WFD 992.75 Ea. 6.0 LPP 24 21 76 X 6WFD22 1048.50 Ea. 138.0 LPP 24 24 76 X 6WFD32 1059.05 Ea. 148.0 LPP 33 76 X 6WFD42 1169.55 Ea. 3.0 LPP 33 21 76 X 6WFD52 04.65 Ea. 166.0 LPP 33 24 76 X 6WFD62 43. Ea. 179.0 LPP Shell, Shelf, Foot Locker & Security Box 76 X 6WFD03 1021.05 Ea. 2.0 LPP 24 76 X 6WFD13 1102.80 Ea. 134.0 LPP 24 21 76 X 6WFD23 14.50 Ea. 146.0 LPP 24 24 76 X 6WFD33 1177.20 Ea. 160.0 LPP 33 76 X 6WFD43 48.90 Ea. 162.0 LPP 33 21 76 X 6WFD53 75.60 Ea. 174.0 LPP 33 24 76 X 6WFD63 1602.40 Ea. 7.0 LPP Height shown for KD Stadium lockers represents the overall height of the frame. Height shown for Welded Stadium lockers represents the overall height of the frame and the 4 high base. Penco Products Inc. 17

Penco Products Inc. All-Welded Lockers All-Welded lockers: Lockers are pre-assembled and welded together at the factory. 14 GA. doors, 16 ga body and GA. back. Diamond-shaped perforations are standard on doors and sides. Classic III stainless steel recessed handle on doors 20" or higher. Number plate at top of door. Box locker doors have padlock staple and door pull with number plate on the door. Available only with continuous hinge. Number plates and door pulls are to be field installed. Coat hooks are standard, and are riveted to the locker at the factory as standard. Field installed coat rods can be substituted for hooks by advance request. Add the cost of the addition of the proper size coat rod and the Coat Rod Bracket for Welded Lockers # 6ACXH76Z (2 per locker opening) in the 'Miscellaneous Locker Parts' section. NOTE: Only lockers 48-1/2" high and taller include a hat shelf. 30-1/2" and 36-1/2" high lockers are not pre-punched to accept shelves. To delete perforations or to add mini-louvers see page 35 and 36. Submit Welded Locker Order Information Form with each order - see page 59. Welded Locker GROUPING INFORMATION All-Welded locker prices assume frame grouping of 4 frames for 9 and wide lockers 3 frames for and wide lockers 2 frames for 24 wide lockers Where smaller groups are necessary, add 10% per frame for 2 wide or 20% for single frames except on 24 wide lockers. Add 10% for single frames of 24 wide lockers. All locker prices are for flat tops, no legs or channel base. NOTE: Penco retains the right to determine All-Welded locker group widths. Maximum group width is usually 54". If site conditions restrict maximum group width, please advise. All-Welded Locker Base and Legs 16 GA. 4 High Integral Channel Base Width Inches Price - Add per Frame Added Wt./Frame 9 9.30 2.3.40 3.0.50 3.8.70 4.5 24 24.80 7.0 4 High Legs Welded to Lockers ALL WIDTHS 16.10.9 Welded lockers are priced by frame but provided by group; for example a 3-wide group will have four legs (one at each corner). Cremone Handle Option Cremone handles are available on standard All- Welded 1, 2 & 3 tier multi-point latch lockers over 9 wide. For the cremone handle option, add the following to the price of the corresponding locker: 1 Tier - $65 per frame (Assumes a single door on 24 wide models) 2 Tier - $135 per frame 3 Tier - $205 per frame Locker Growth for All-Welded Lockers When a welded locker group is installed next to another locker group the overall width increases by 1/16" per group. Example: A locker group of 45" installed next to a locker group of 45" results in a total overall width of the two locker groups of 90-1/8". All-Welded Lockers 1 Tier (36-1/2", hat shelf NOT included) 36-1/2 X 6WP3 401.25 Frm. 36.0 LPP 36-1/2 X 6WP4 427.10 Frm. 37.0 LPP 36-1/2 X 6WP5 453.00 Frm. 40.0 LPP 1 Tier (48-1/2") 48-1/2 X 6WP163 430.35 Frm. 51.0 LPP 48-1/2 X 6WP164 456.40 Frm. 52.0 LPP 48-1/2 X 6WP165 481.45 Frm. 54.0 LPP 1 Tier (60") 9 60 X 6WP100 4.60 Frm. 53.8 LPP 9 60 X 6WP101 439.30 Frm. 57.4 LPP 9 60 X 6WP102 459.95 Frm. 61.1 LPP 60 X 6WP103 439.30 Frm. 60.9 LPP 60 X 6WP104 463.60 Frm. 65.0 LPP 60 X 6WP105 488.00 Frm. 69.2 LPP 21 60 X 6WP106 513.80 Frm. 72.4 LPP 24 60 X 6WP107 540.45 Frm. 75.5 LPP 60 X 6WP108 479.70 Frm. 74.0 LPP 60 X 6WP109 501.20 Frm. 75.5 LPP 60 X 6WP110 523.70 Frm. 78.8 LPP 21 60 X 6WP111 548. Frm. 83.1 LPP 24 60 X 6WP1 574.35 Frm. 85.6 LPP 60 X 6WP172 492.60 Frm. 71.3 LPP 60 X 6WP173 524.10 Frm. 78.4 LPP 60 X 6WP113 557.60 Frm. 85.4 LPP 21 60 X 6WP114 593.30 Frm. 92.6 LPP 24 60 X 6WP1 611.85 Frm. 99.9 LPP 24 60 X 6WP116 797.85 Frm. 104.3 LPP 24 21 60 X 6WP117 807. Frm. 110.3 LPP 24 24 60 X 6WP1 824.10 Frm. 116.3 LPP 1 Tier (72") 9 72 X 6WP0 439.30 Frm. 61.3 LPP 9 72 X 6WP1 459.95 Frm. 65.3 LPP 9 72 X 6WP2 480.60 Frm. 69.3 LPP 72 X 6WP3 461.85 Frm. 70.7 LPP 72 X 6WP4 484.35 Frm. 74.6 LPP 72 X 6WP5 508.70 Frm. 79.5 LPP 21 72 X 6WP6 534.40 Frm. 84.5 LPP 24 72 X 6WP7 561.45 Frm. 89.5 LPP 72 X 6WP8 510.25 Frm. 77.9 LPP 72 X 6WP9 529.35 Frm. 83.7 LPP 72 X 6WP130 548. Frm. 89.1 LPP 21 72 X 6WP131 585.70 Frm. 93.0 LPP 24 72 X 6WP132 624.95 Frm. 99.0 LPP 72 X 6WP2 5.55 Frm. 84.8 LPP 72 X 6WP3 544.80 Frm. 91.0 LPP 72 X 6WP133 572.50 Frm. 97.3 LPP 21 72 X 6WP134 600.70 Frm. 104.8 LPP 24 72 X 6WP135 638.30 Frm. 1.9 LPP 24 72 X 6WP136 820.40 Frm. 1.2 LPP 24 21 72 X 6WP137 844.75 Frm. 4.2 LPP 24 24 72 X 6WP138 858.00 Frm. 7.0 LPP

All-Welded Lockers 2 Tier (60") 30 X 6WP203 5.20 Frm. 64.1 LPP 30 X 6WP204 529.35 Frm. 68.3 LPP 30 X 6WP205 559.40 Frm. 72.7 LPP 21 30 X 6WP206 591.35 Frm. 77.0 LPP 24 30 X 6WP207 625.05 Frm. 82.0 LPP 30 X 6WP208 571. Frm. 72.0 LPP 30 X 6WP209 585.70 Frm. 77.9 LPP 30 X 6WP210 600.70 Frm. 81.7 LPP 21 30 X 6WP211 638.30 Frm. 86.3 LPP 24 30 X 6WP2 679.20 Frm. 90.0 LPP 30 X 6WP273 602.45 Frm. 81.1 LPP 30 X 6WP213 660.75 Frm. 89.3 LPP 21 30 X 6WP214 720.80 Frm. 97.1 LPP 24 30 X 6WP2 750.90 Frm. 106.3 LPP 24 30 X 6WP216 803.45 Frm. 109.5 LPP 24 21 30 X 6WP217 814.65 Frm. 114.5 LPP 24 24 30 X 6WP2 837.35 Frm. 1.3 LPP 2 Tier (72") 36 X 6WP223 536.85 Frm. 73.2 LPP 36 X 6WP224 578.20 Frm. 77.6 LPP 36 X 6WP225 600.70 Frm. 82.4 LPP 21 36 X 6WP226 623.20 Frm. 87.2 LPP 24 36 X 6WP227 647.65 Frm. 90.2 LPP 36 X 6WP228 616.05 Frm. 85.2 LPP 36 X 6WP229 630.75 Frm. 87.6 LPP 36 X 6WP230 645.85 Frm. 92.4 LPP 21 36 X 6WP231 694.55 Frm. 97.2 LPP 24 36 X 6WP232 745.45 Frm. 102.0 LPP 36 X 6WP282 606.05 Frm. 83.8 LPP 36 X 6WP283 655.85 Frm. 92.2 LPP 36 X 6WP233 687.00 Frm. 100.6 LPP 21 36 X 6WP234 724.60 Frm. 109.0 LPP 24 36 X 6WP235 765.85 Frm. 1.6 LPP 24 36 X 6WP236 893.55 Frm. 3.0 LPP 24 21 36 X 6WP237 957.30 Frm. 9.0 LPP 24 24 36 X 6WP238 991. Frm. 135.4 LPP 3 Tier (60") 20 X 6WP303 625.20 Frm. 70.0 LPP 20 X 6WP304 647.65 Frm. 74.8 LPP 20 X 6WP305 664.45 Frm. 79.6 LPP 21 20 X 6WP306 681.80 Frm. 81.6 LPP 24 20 X 6WP307 699.45 Frm. 89.0 LPP 20 X 6WP308 698.10 Frm. 80.0 LPP 20 X 6WP309 709.50 Frm. 86.5 LPP 20 X 6WP310 720.80 Frm. 93.7 LPP 21 20 X 6WP311 760.30 Frm. 99.1 LPP 24 20 X 6WP3 803.20 Frm. 101.8 LPP 20 X 6WP313 782.65 Frm. 108.8 LPP 21 20 X 6WP314 826.85 Frm. 110.0 LPP 24 20 X 6WP3 872.35 Frm. 119.5 LPP 3 Tier (72") 24 X 6WP323 653.30 Frm. 80.7 LPP 24 X 6WP324 670.20 Frm. 85.8 LPP 24 X 6WP325 687.00 Frm. 90.9 LPP 21 24 X 6WP326 704.65 Frm. 93.5 LPP 24 24 X 6WP327 722.70 Frm. 99.0 LPP 24 X 6WP328 7.40 Frm. 94.0 LPP 24 X 6WP329 724.75 Frm. 98.9 LPP 24 X 6WP330 732. Frm. 106.1 LPP 21 24 X 6WP331 760.30 Frm. 109.2 LPP 24 24 X 6WP332 8.85 Frm. 1.5 LPP 24 X 6WP333 836.75 Frm. 114.3 LPP 21 24 X 6WP334 881.55 Frm. 130.5 LPP 24 24 X 6WP335 928.80 Frm. 137.9 LPP 4 Tier Box Locker (60") X 6WP403 586.55 Frm. 66.5 LPP X 6WP404 607.90 Frm. 71.7 LPP X 6WP405 623.75 Frm. 77.3 LPP 21 X 6WP406 639.90 Frm. 81.5 LPP 24 X 6WP407 656.60 Frm. 87.5 LPP X 6WP408 655.25 Frm. 70.5 LPP X 6WP409 671.40 Frm. 78.5 LPP X 6WP410 676.60 Frm. 85.1 LPP 21 X 6WP411 713.60 Frm. 91.5 LPP 24 X 6WP4 753.75 Frm. 98.5 LPP 4 Tier Box Locker (72") X 6WP423 613.10 Frm. 75.0 LPP X 6WP424 629.10 Frm. 80.6 LPP X 6WP425 644.95 Frm. 86.6 LPP 21 X 6WP426 661.40 Frm. 92.0 LPP 24 X 6WP427 678.45 Frm. 97.0 LPP X 6WP428 671.55 Frm. 81.0 LPP X 6WP429 680.40 Frm. 89.0 LPP X 6WP430 687.20 Frm. 96.0 LPP 21 X 6WP431 713.60 Frm. 103.0 LPP 24 X 6WP432 768.70 Frm. 106.0 LPP All-Welded Locker Base and Legs 16 GA. 4 High Integral Channel Base Width Inches Price - Add per Frame Added Wt./Frame 9 9.30 2.3.40 3.0.50 3.8.70 4.5 24 24.80 7.0 4 High Legs Welded to Lockers ALL WIDTHS 16.10.9 Welded lockers are priced by frame but provided by group; for example a 3-wide group will have four legs (one at each corner). HEIGHT: Height shown is the nominal opening height for 1, 2, 3, 4, 5, & 6 tier lockers. It represents the overall height of the frame for all others. Height does NOT include the standard 6" legs. Penco Products Inc. 19

All-Welded Lockers 5 Tier Box Locker (60") X 6WP503 611.75 Frm. 71.5 LPP X 6WP504 634.05 Frm. 77.0 LPP X 6WP505 650.50 Frm. 83.0 LPP 21 X 6WP506 667.45 Frm. 87.5 LPP 24 X 6WP507 684.75 Frm. 94.5 LPP X 6WP508 683.40 Frm. 76.5 LPP X 6WP509 700. Frm. 87.5 LPP X 6WP510 705.65 Frm. 95.7 LPP 21 X 6WP511 744.30 Frm. 102.5 LPP 24 X 6WP5 786.20 Frm. 106.5 LPP X 6WP513 765.50 Frm. 108.7 LPP 21 X 6WP514 807.40 Frm. 1.7 LPP 5 Tier Box Locker (72") 14-2/5 X 6WP523 639.60 Frm. 79.0 LPP 14-2/5 X 6WP524 656. Frm. 85.5 LPP 14-2/5 X 6WP525 672.65 Frm. 92.0 LPP 21 14-2/5 X 6WP526 689.90 Frm. 98.0 LPP 24 14-2/5 X 6WP527 707.55 Frm. 105.0 LPP 14-2/5 X 6WP528 700.45 Frm. 85.0 LPP 14-2/5 X 6WP529 709.65 Frm. 96.8 LPP 14-2/5 X 6WP530 716.70 Frm. 104.5 LPP 21 14-2/5 X 6WP531 744.30 Frm. 1.3 LPP 24 14-2/5 X 6WP532 801.70 Frm. 1.0 LPP 6 Tier Box Locker (72") X 6WP623 638.00 Frm. 81.6 LPP X 6WP624 661.30 Frm. 87.0 LPP X 6WP625 678.50 Frm. 89.4 LPP 21 X 6WP626 696.20 Frm. 94.0 LPP 24 X 6WP627 714.20 Frm. 111.0 LPP X 6WP628 7.80 Frm. 90.0 LPP X 6WP629 730.35 Frm. 99.6 LPP X 6WP630 736.00 Frm. 108.0 LPP 21 X 6WP631 776.25 Frm. 116.4 LPP 24 X 6WP632 819.90 Frm. 6.0 LPP X 6WP633 798.40 Frm. 8.1 LPP 21 X 6WP634 842.05 Frm. 136.5 LPP 8 Tier Box Locker (72") 9 X 6WP823 720.80 Frm. 90.2 LPP 9 X 6WP824 735.85 Frm. 98.2 LPP 9 X 6WP825 781.00 Frm. 108.6 LPP 9 X 6WP828 905.05 Frm. 106.0 LPP 9 X 6WP829 924.00 Frm. 111.0 LPP 9 X 6WP830 945.60 Frm. 2.0 LPP 9 Tier Box Locker (72") 8 X 6WP923 760.30 Frm. 96.6 LPP 8 X 6WP924 794.00 Frm. 105.6 LPP 8 X 6WP925 827.85 Frm. 114.6 LPP 8 X 6WP928 954.00 Frm. 106.0 LPP 8 X 6WP929 996.60 Frm. 117.0 LPP 8 X 6WP930 1038.85 Frm. 132.0 LPP Welded Locker GROUPING INFORMATION All-Welded locker prices assume frame grouping of 4 frames for 9 and wide lockers 3 frames for and wide lockers 2 frames for 24 wide lockers Where smaller groups are necessary, add 10% per frame for 2 wide or 20% for single frames except on 24 wide lockers. Add 10% for single frames of 24 wide lockers. All locker prices are for flat tops, no legs or channel base. NOTE: Penco retains the right to determine All-Welded locker group widths. Maximum group width is usually 54". If site conditions restrict maximum group width, please advise. HEIGHT: Height shown is the nominal opening height for 1, 2, 3, 4, 5, & 6 tier lockers. It represents the overall height of the frame for all others. Height does NOT include the standard 6" legs. 20 Penco Products Inc.

All-Welded Defiant II Lockers 1 Tier (36-1/2", hat shelf NOT included) 36-1/2 X 6WD3 403.80 Frm. 37.0 LPP 36-1/2 X 6WD4 429.70 Frm. 38.0 LPP 36-1/2 X 6WD5 455.60 Frm. 41.0 LPP 1 Tier (48-1/2") 48-1/2 X 6WD163 434.85 Frm. 52.0 LPP 48-1/2 X 6WD164 461.40 Frm. 53.0 LPP 48-1/2 X 6WD165 485.50 Frm. 55.0 LPP 1 Tier (60") 60 X 6WD103 441. Frm. 62.5 LPP 60 X 6WD104 465.60 Frm. 66.9 LPP 60 X 6WD105 489.95 Frm. 71.6 LPP 60 X 6WD109 503.10 Frm. 77.0 LPP 60 X 6WD110 525.65 Frm. 81.2 LPP 21 60 X 6WD111 550.05 Frm. 85.9 LPP 60 X 6WD172 494.30 Frm. 73.4 LPP 60 X 6WD173 525.85 Frm. 80.6 LPP 60 X 6WD113 559.40 Frm. 87.8 LPP 21 60 X 6WD114 595.05 Frm. 95.6 LPP 24 60 X 6WD1 613.80 Frm. 103.1 LPP 24 60 X 6WD116 802.80 Frm. 107.0 LPP 24 21 60 X 6WD117 814.50 Frm. 113.0 LPP 24 24 60 X 6WD1 831.20 Frm. 119.0 LPP 1 Tier (72") 72 X 6WD3 463.60 Frm. 72.2 LPP 72 X 6WD4 486.30 Frm. 76.5 LPP 72 X 6WD5 510.60 Frm. 81.4 LPP 72 X 6WD8 5.55 Frm. 79.6 LPP 72 X 6WD9 531.20 Frm. 85.6 LPP 72 X 6WD130 550.05 Frm. 91.5 LPP 21 72 X 6WD131 587.55 Frm. 96.8 LPP 72 X 6WD133 574.50 Frm. 99.7 LPP 21 72 X 6WD134 602.55 Frm. 107.6 LPP 24 72 X 6WD135 640.10 Frm. 116.1 LPP 24 72 X 6WD136 826.40 Frm. 1.0 LPP 24 21 72 X 6WD137 851.50 Frm. 7.0 LPP 24 24 72 X 6WD138 865.85 Frm. 130.0 LPP 2 Tier (60") 30 X 6WD203 522.00 Frm. 67.2 LPP 30 X 6WD204 533.00 Frm. 72.2 LPP 30 X 6WD205 563.25 Frm. 77.6 LPP 30 X 6WD208 574.75 Frm. 80.0 LPP 30 X 6WD209 589.45 Frm. 81.8 LPP 30 X 6WD210 604.35 Frm. 86.6 LPP 21 30 X 6WD211 642.05 Frm. 92.0 LPP 30 X 6WD213 664.45 Frm. 94.2 LPP 21 30 X 6WD214 724.60 Frm. 102.8 LPP 24 30 X 6WD2 754.65 Frm. 1.0 LPP 2 Tier (72") 36 X 6WD223 540.55 Frm. 76.2 LPP 36 X 6WD224 582.00 Frm. 81.6 LPP 36 X 6WD225 604.35 Frm. 87.4 LPP All-Welded Defiant II Lockers All-Welded "Defiant II" (1, 2, 3 tier only): Same as All-Welded, except that the 14 GA. door has single point latch construction. No latch channel or moving parts in the door. Doors have a full height vertical pan welded to top, bottom and and hinge-side flanges as well as to the 14 GA. door skin for extra stiffness (doors wider than have a horizontal pan). Stainless steel recessed pocket with an integral door pull. Number plate at top of door. Number plates are to be field installed. Coat hooks are standard, and are riveted to the locker at the factory as standard. Field installed coat rods can be substituted for hooks by advance request. Add the cost of the addition of the proper size coat rod and the Coat Rod Bracket for Welded Lockers # 6ACXH76Z (2 per locker opening) in the 'Miscellaneous Locker Parts' section. To delete perforations or to add mini-louvers see page 35 and 36. Submit Welded Locker Order Information Form with Each Order - see page 59. 36 X 6WD228 621.95 Frm. 87.0 LPP 36 X 6WD229 635.45 Frm. 90.0 LPP 36 X 6WD230 649.50 Frm. 97.4 LPP 21 36 X 6WD231 698.40 Frm. 103.2 LPP 24 36 X 6WD232 749.95 Frm. 109.0 LPP 36 X 6WD233 690.75 Frm. 105.6 LPP 21 36 X 6WD234 728.30 Frm. 1.0 LPP 24 36 X 6WD235 769.55 Frm. 5.2 LPP 3 Tier (60") 20 X 6WD303 630.75 Frm. 72.5 LPP 20 X 6WD304 653.30 Frm. 77.3 LPP 20 X 6WD305 670.20 Frm. 82.1 LPP 20 X 6WD309 7.25 Frm. 89.0 LPP 20 X 6WD310 726.45 Frm. 96.2 LPP 21 20 X 6WD311 765.85 Frm. 101.6 LPP 3 Tier (72") 24 X 6WD323 658.90 Frm. 83.7 LPP 24 X 6WD324 675.80 Frm. 88.8 LPP 24 X 6WD325 692.60 Frm. 93.9 LPP 24 X 6WD329 728.60 Frm. 100.8 LPP 24 X 6WD330 737.75 Frm. 108.2 LPP 21 24 X 6WD331 765.85 Frm. 111.6 LPP 24 X 6WD333 841.70 Frm. 116.7 LPP 21 24 X 6WD334 886.80 Frm. 132.8 LPP 24 24 X 6WD335 934.00 Frm. 140.2 LPP Rotary Locks Rotary or wrap-around style built-in locks cannot be used on a standard Defiant II locker latch. For these applications, specify the Defiant II-R option that includes a special hasp and a pocket with no padlock slot. There is no charge for this option but it must be clearly called out on the purchase order or estimate sheet and may add to the order lead time. Please specify the lock that will be used whether they are ordered from Penco or directly from the lock manufacturer. Lockers equipped with this option are configured for use ONLY with a rotary style lock. Locks must be ordered separately. All-Welded Locker Base and Legs 16 GA. 4 High Integral Channel Base Width Inches Price - Add per Frame Added Wt./Frame 9 9.30 2.3.40 3.0.50 3.8.70 4.5 24 24.80 7.0 4 High Legs Welded to Lockers ALL WIDTHS 16.10.9 Welded lockers are priced by frame but provided by group; for example a 3-wide group will have four legs (one at each corner). Penco Products Inc. 21

Angle Iron Lockers - Single Point Latch 1 Tier (60") 60 X 6WA103 529.35 Frm. 58.0 LPP 60 X 6WA104 558.70 Frm. 63.0 LPP 60 X 6WA105 587.90 Frm. 68.0 LPP 60 X 6WA109 603.70 Frm. 71.0 LPP 60 X 6WA110 630.80 Frm. 77.0 LPP 60 X 6WA173 642.45 Frm. 80.0 LPP 60 X 6WA113 671.25 Frm. 86.0 LPP 21 60 X 6WA114 701.35 Frm. 92.1 LPP 24 60 X 6WA1 732.85 Frm. 98.3 LPP 24 60 X 6WA116 957.40 Frm. 96.0 LPP 24 21 60 X 6WA117 968.65 Frm. 102.5 LPP 24 24 60 X 6WA1 988.90 Frm. 108.9 LPP 1 Tier (72") 72 X 6WA3 556.35 Frm. 67.0 LPP 72 X 6WA4 583.50 Frm. 73.0 LPP 72 X 6WA5 6.75 Frm. 79.0 LPP 72 X 6WA8 6.05 Frm. 75.0 LPP 72 X 6WA9 637.45 Frm. 82.0 LPP 72 X 6WA130 659.95 Frm. 88.0 LPP 72 X 6WA3 653.80 Frm. 93.0 LPP 72 X 6WA133 689.35 Frm. 98.0 LPP 21 72 X 6WA134 726.90 Frm. 106.5 LPP 24 72 X 6WA135 766.45 Frm. 113.9 LPP 24 72 X 6WA136 984.40 Frm. 119.0 LPP 24 21 72 X 6WA137 1013.70 Frm. 7.8 LPP 24 24 72 X 6WA138 1029.50 Frm. 136.9 LPP 2 Tier (60") 30 X 6WA203 626.35 Frm. 61.0 LPP 30 X 6WA204 639.65 Frm. 66.0 LPP 30 X 6WA205 675.85 Frm. 72.0 LPP 30 X 6WA208 689.65 Frm. 68.0 LPP 30 X 6WA209 707.40 Frm. 75.0 LPP 30 X 6WA210 725.25 Frm. 81.0 LPP 30 X 6WA273 723.00 Frm. 84.0 LPP 30 X 6WA213 797.35 Frm. 91.0 LPP 21 30 X 6WA214 869.45 Frm. 99.2 LPP 2 Tier (72") 36 X 6WA223 648.70 Frm. 69.0 LPP 36 X 6WA224 698.40 Frm. 75.0 LPP 36 X 6WA225 725.25 Frm. 81.0 LPP 36 X 6WA228 746.30 Frm. 78.0 LPP 36 X 6WA229 762.50 Frm. 84.0 LPP 36 X 6WA230 779.40 Frm. 90.0 LPP 36 X 6WA283 787.00 Frm. 91.9 LPP 36 X 6WA233 828.90 Frm. 98.0 LPP 21 36 X 6WA234 865.00 Frm. 106.1 LPP Angle Iron Welded Lockers: Pre-assembled and welded together at the factory. Lockers utilize a frame made from 1 x 1 x 1/8 pickled angle iron steel. 14 gauge diamond perforated doors and 16 gauge tops, bottoms & shelves are standard. Locker sides are made from 14 GA. steel with diamond-shaped perforations or solid 16. GA. steel (13 gauge ¾ flattened expanded metal sides are optional). Door hinges are 16 Ga. continuous, welded to the door and riveted to the frame. 3 high hinges welded to the door and to the frame are optional at no additional charge. Number plates and door pulls are field-installed. A 4 high 14 gauge welded steel base can be ordered as an option (see page 23). To delete perforations in the door, see page 31. Six tier box locker doors are equipped with a door pull/friction catch. Different types of door latching are available for 1 and 2 tier lockers - Defiant II Single Point Latch and Cremone turn-handle 3 point latch as shown below. See Lock Application Table for locks compatible with each type of locker door. For A.D.A. requirements, contact a sales representative. Submit Welded Locker Order Information Form with each order - See page 59. To review Angle Iron Locker Group Widths - See page 23. Defiant II Single Point Latch doors have a stainless steel recessed pocket with an integral door pull. Doors have a full height vertical pan welded to the top, bottom and hinge side flanges as well as to the 14 ga. door skin for extra stiffness (doors wider than have a horizontal pan). Angle Iron Lockers Cremone Turn Handle doors have a 3-point latching system utilizing 3/8 latching rods that engage the top and bottom door frames, and a 1/8 thick center latch that engages at the door frame. 3 Tier Locker (60") 20 X 6WA303 750.25 Frm. 69.7 LPP 20 X 6WA304 777. Frm. 74.0 LPP 20 X 6WA305 797.40 Frm. 79.2 LPP 20 X 6WA308 837.65 Frm. 80.0 LPP 20 X 6WA309 851.50 Frm. 86.0 LPP 20 X 6WA310 865.60 Frm. 92.6 LPP 20 X 6WA313 939.20 Frm. 108.0 LPP 21 20 X 6WA314 992.20 Frm. 109.6 LPP 24 20 X 6WA3 1046.80 Frm. 119.0 LPP 3 Tier Locker (72") 24 X 6WA323 783.95 Frm. 80.2 LPP 24 X 6WA324 804.25 Frm. 85.4 LPP 24 X 6WA325 824.45 Frm. 90.5 LPP 24 X 6WA328 858.55 Frm. 96.2 LPP 24 X 6WA329 869.80 Frm. 98.5 LPP 24 X 6WA330 880.70 Frm. 105.7 LPP 24 X 6WA333 1004.10 Frm. 114.0 LPP 21 24 X 6WA334 1057.90 Frm. 130.0 LPP 24 24 X 6WA335 1114.60 Frm. 137.6 LPP Angle Iron Box Lockers 6 Tier Box Locker (72") X 6WA623 765.60 Frm. 76.7 LPP X 6WA624 793.60 Frm. 81.8 LPP X 6WA625 814.20 Frm. 84.0 LPP 21 X 6WA626 835.35 Frm. 88.0 LPP 24 X 6WA627 857.10 Frm. 104.0 LPP X 6WA628 855.40 Frm. 84.6 LPP X 6WA629 876.40 Frm. 93.6 LPP X 6WA630 883.25 Frm. 101.5 LPP 21 X 6WA631 931.50 Frm. 109.4 LPP 24 X 6WA632 983.90 Frm. 1.4 LPP Angle Iron Group Widths Groupings with Angle Iron lockers are different from all other Penco lockers because the intermediate division has a common 1" angle. The hinge is welded to the left side of the vertical door frame and the latch is welded to the right side. The use of a common frame element causes the growth factor to vary depending upon the number of lockers in the grouping. The use of larger groupings will reduce the overall growth issue on any installation. See Page 23 for table of Angle Iron Locker Group Widths. HEIGHT: Height shown is the nominal opening height for 1, 2, 3, & 6-tier lockers. Heights do not include optional 4" high Channel Base. 22 Penco Products Inc.

Angle Iron Lockers with Cremone Turn Handle Angle Iron Lockers - Cremone Turn Handle 1 Tier (60") 60 X 6WAT103 558.55 Frm. 59.0 LPP 60 X 6WAT104 587.85 Frm. 64.0 LPP 60 X 6WAT105 617.00 Frm. 69.0 LPP 60 X 6WAT109 632.85 Frm. 72.0 LPP 60 X 6WAT110 659.90 Frm. 78.0 LPP 60 X 6WAT173 674.90 Frm. 81.0 LPP 60 X 6WAT113 700.65 Frm. 87.0 LPP 21 60 X 6WAT114 737.20 Frm. 93.4 LPP 24 60 X 6WAT1 770.35 Frm. 99.8 LPP 24 60 X 6WAT116 1006. Frm. 99.5 LPP 24 21 60 X 6WAT117 10.00 Frm. 104.1 LPP 24 24 60 X 6WAT1 1039.30 Frm. 110.5 LPP 1 Tier (72") 72 X 6WAT3 585.65 Frm. 68.0 LPP 72 X 6WAT4 6.70 Frm. 74.0 LPP 72 X 6WAT5 641.85 Frm. 80.0 LPP 72 X 6WAT8 643.70 Frm. 76.0 LPP 72 X 6WAT9 666.75 Frm. 83.0 LPP 72 X 6WAT130 689.20 Frm. 89.0 LPP 72 X 6WAT3 682.80 Frm. 94.0 LPP 72 X 6WAT133 7.40 Frm. 99.0 LPP 21 72 X 6WAT134 758.85 Frm. 107.5 LPP 24 72 X 6WAT135 800.20 Frm. 114.9 LPP 24 72 X 6WAT136 1027.70 Frm. 0.6 LPP 24 21 72 X 6WAT137 1058.30 Frm. 9.3 LPP 24 24 72 X 6WAT138 1074.85 Frm. 138.4 LPP 2 Tier (60") 30 X 6WAT203 672. Frm. 62.0 LPP 30 X 6WAT204 685.60 Frm. 68.0 LPP 30 X 6WAT205 721.60 Frm. 74.0 LPP 30 X 6WAT208 735.80 Frm. 70.0 LPP 30 X 6WAT209 753. Frm. 77.0 LPP 30 X 6WAT210 771.25 Frm. 83.0 LPP 30 X 6WAT273 754.90 Frm. 86.0 LPP 30 X 6WAT213 843.20 Frm. 93.0 LPP 21 30 X 6WAT214 907.75 Frm. 101.2 LPP Welded Locker GROUPING INFORMATION Where smaller groups are necessary, add 10% per frame for 2 wide or 20% for single frames except on 24 wide lockers. Add 10% for single frames of 24 wide lockers. 2 Tier (72") 36 X 6WAT223 694.60 Frm. 70.0 LPP 36 X 6WAT224 744.20 Frm. 76.0 LPP 36 X 6WAT225 771.25 Frm. 82.0 LPP 36 X 6WAT228 789.60 Frm. 79.0 LPP 36 X 6WAT229 807.20 Frm. 85.0 LPP 36 X 6WAT230 825.35 Frm. 91.0 LPP 36 X 6WAT283 821.70 Frm. 93.0 LPP 36 X 6WAT233 874.80 Frm. 99.0 LPP 21 36 X 6WAT234 903.05 Frm. 107.8 LPP 3 Tier (60") 20 X 6WAT303 813.10 Frm. 71.0 LPP 20 X 6WAT304 840.05 Frm. 75.5 LPP 20 X 6WAT305 860.35 Frm. 80.6 LPP 20 X 6WAT308 900.60 Frm. 88.7 LPP 20 X 6WAT309 914.40 Frm. 90.4 LPP 20 X 6WAT310 928.55 Frm. 94.5 LPP 20 X 6WAT313 1014.65 Frm. 110.5 LPP 21 20 X 6WAT314 1055.10 Frm. 111.9 LPP 24 20 X 6WAT3 1070.85 Frm. 1.4 LPP 3 Tier (72") 24 X 6WAT323 846.85 Frm. 82.0 LPP 24 X 6WAT324 867. Frm. 87.3 LPP 24 X 6WAT325 887.40 Frm. 92.6 LPP 24 X 6WAT328 921.50 Frm. 98.2 LPP 24 X 6WAT329 932.70 Frm. 100.6 LPP 24 X 6WAT330 943.60 Frm. 107.9 LPP 24 X 6WAT333 1066.95 Frm. 117.0 LPP 21 24 X 6WAT334 10.80 Frm. 133.0 LPP 24 24 X 6WAT335 1177.50 Frm. 140.6 LPP Locker Base for Angle Iron 14 GA. 4 High Integral Channel Base Width Inches Price - Add per Frame Added Wt./Frame 14.80 3.8.55 4.8 22.20 6.1 24" 26.40 7.8 4 legs are NOT available on Angle Iron lockers. Angle Iron Locker Group Widths Groupings with Angle Iron lockers are different from all other Penco lockers. This is because the intermediate division has a common 1" angle: the hinge is welded to the left side and the latch is welded to the right. The use of a common frame element causes the growth factor to vary depending upon the number of lockers in the grouping. The use of larger groupings will reduce the overall growth issue on any installation - see the chart at the right for specifics. Angle Iron Locker Group Widths Frame Width " Frame " Frame " Frame 24" Frame Grouping Width 5 wide max 60.00" 4 wide max 48.20" 3 wide max 36.40" 2 wide max 24.60" 1 wide max.80" 4 wide max 60.00" 3 wide max 45.25" 2 wide max 30.50" 1 wide max.75" 3 wide max 54.00" 2 wide max 36.33" 1 wide max.67" 2 wide max 48.00" 1 wide max 24.50" Penco Products Inc. 23

Patriot Gear & Turnout Locker Introduction Patriot heavy duty readiness lockers are ideally suited for military, fire, EMS, police and other first responders. Patriot Gear and Turnout lockers are available in KD construction (Knocked Down) in 72" height only and in Welded construction with a height of 76" only (which includes a 14 gauge 4" high integral closed base & bottom as standard). No other legs or bases are available. This section covers two basic types of Patriot lockers; Gear lockers and Turnout lockers. All Patriot Gear and Turnout Lockers include the following standard equipment: One-wide construction Full width hat shelf at " from the top Heavy duty 1" diameter, chrome plated coat rod. (Brackets are light gray only.) 2 heavy duty hooks mounted on the locker back Number plates, coat hooks, coat rods and door pulls (all of which are to be field installed) Environmentally friendly powder coat finish. Two-tone finishes are available at no charge, assuming use of standard Penco colors. Any request must be accompanied by a clear description of the combination desired. Steel Gauges 16 gauge diamond perforated sides 16 gauge top, shelf and front frame gauge solid back 14 gauge integral channel base & bottom on welded models; 16 gauge bottom on KD models Gear Lockers: 14 gauge louvered doors Cremone-style turn handle - can be locked with a built-in lock or a padlock. Double doors on all Gear models over " wide, except as noted. Continuous hinges on Gear models Standard door ventilation is louvers at the top and the bottom No charge Gear locker options: Classic III or Defiant handle on single door models Single door on 24" models with turn handle, Classic III or Defiant handle Diamond perforations, mini louvers or solid doors Turnout Lockers: These lockers have open fronts. Items can be secured by ordering an optional security box for the top shelf, a lockable foot locker which also doubles as a seat, or a heavy duty drawer unit. Accessories: Patriot locker have their own exclusive accessories, which are NOT intended for use on other locker models. See the list of accessories following the locker models below. NOTE: Requested features not listed as standard equipment must be clearly identified on the purchase order. Most Patriot Gear and Turnout accessories are NOT designed for use on Patriot Duty lockers. Gear Lockers Turnout Lockers Patriot Gear Locker - front view showing cremone handle. Patriot Gear Locker with optional Center Partition, Full Width Metal Bottom Shelf, Mirror & Cell Phone/ Key Tray. Patriot Turnout Locker with optional Hardwood Bench Seat. Patriot Turnout Locker with optional Two-Tone finish, Center Partition, 3 Half Shelves & 24" wide Security Box. 24 Penco Products Inc.

Patriot Gear & Turnout Lockers & Accessories Patriot Gear Lockers - KD (SINGLE Door with Cremone Turn Handle) " deep Hat Shelf. 1-Wide. 72 X 6KGDA84 938.45 Ea. 100.0 24 72 X 6KGDA94 959.45 Ea. 130.0 21" deep Hat Shelf. 1-Wide. 24 72 X 6KGDA82 989.00 Ea. 132.0 24 24 72 X 6KGDA92 1101.70 Ea. 2.0 (Double Doors with Cremone Turn Handle) " deep Hat Shelf. 1-Wide. 24 72 XY 6KGDA04 1029.00 Ea. 130.0 30 72 XY 6KGDA14 1199.50 Ea. 0.0 36 72 XY 6KGDA24 75.95 Ea. 170.0 24 24 72 XY 6KGDA00 1099.35 Ea. 0.0 30 24 72 XY 6KGDA10 17.80 Ea. 170.0 36 24 72 XY 6KGDA20 1389.90 Ea. 190.0 42 24 72 XY 6KGDA30 1435.65 Ea. 210.0 48 24 72 XY 6KGDA40 54.20 Ea. 230.0 21" deep Hat Shelf. 1-Wide. 24 24 72 XY 6KGDA02.35 Ea. 160.0 30 24 72 XY 6KGDA 20.70 Ea. 0.0 36 24 72 XY 6KGDA22 1393.60 Ea. 200.0 42 24 72 XY 6KGDA32 1440.25 Ea. 220.0 48 24 72 XY 6KGDA42 60.10 Ea. 240.0 Patriot Gear Lockers - Welded All-Welded models include integral 4" base. (SINGLE Door with Cremone Turn Handle) " deep Hat Shelf. 1-Wide. 76 X 6WGDA84C 1176.00 Ea. 111.3 24 76 X 6WGDA94C 24.20 Ea. 133.3 21" deep Hat Shelf. 1-Wide. 24 76 X 6WGDA82C 1334.75 Ea. 131.3 24 24 76 X 6WGDA92C 1381.80 Ea. 3.3 (Double Doors with Cremone Turn Handle) " deep Hat Shelf. 1-Wide. 24 76 XY 6WGDA04C 93.60 Ea. 133.3 30 76 XY 6WGDA14C 16.35 Ea. 5.0 36 76 XY 6WGDA24C 1704.45 Ea. 191.3 24 24 76 XY 6WGDA00C 1458. Ea. 0.0 30 24 76 XY 6WGDA10C 1663.20 Ea. 170.0 36 24 76 XY 6WGDA20C 1748.95 Ea. 190.0 42 24 76 XY 6WGDA30C 32.00 Ea. 210.0 48 24 76 XY 6WGDA40C 1922.55 Ea. 230.0 21" deep Hat Shelf. 1-Wide. 24 24 76 XY 6WGDA02C 1460.50 Ea. 3.3 30 24 76 XY 6WGDAC 1666. Ea. 175.0 36 24 76 XY 6WGDA22C 1752.65 Ea. 211.3 42 24 76 XY 6WGDA32C 36.60 Ea. 235.0 48 24 76 XY 6WGDA42C 1928.40 Ea. 242.0 Note Regarding KD Gear Lockers: Knocked down Patriot Gear lockers measuring more than 24 wide will have their doors packaged separately from the door frame. They will have to be mounted during final assembly using the supplied rivets. This is done to prevent damage and make it easier to assemble the locker bodies. Patriot Turnout Lockers - KD (No Doors) " deep Hat Shelf. 1-Wide. 72 X 6KTDA84 640.90 Ea. 82.0 24 72 X 6KTDA04 705.60 Ea. 102.0 30 72 X 6KTDA14 758.50 Ea. 142.0 36 72 X 6KTDA24 882.00 Ea. 142.0 24 24 72 X 6KTDA00 771.45 Ea. 1.0 30 24 72 X 6KTDA10 859.65 Ea. 141.0 36 24 72 X 6KTDA20 923. Ea. 161.0 42 24 72 X 6KTDA30 971.40 Ea. 1.0 48 24 72 X 6KTDA40 1037.25 Ea. 201.0 21" deep Hat Shelf. 1-Wide. 24 72 X 6KTDA82 711.50 Ea. 102.0 24 24 72 X 6KTDA02 776. Ea. 3.0 30 24 72 X 6KTDA 864.35 Ea. 143.0 36 24 72 X 6KTDA22 929.05 Ea. 161.0 42 24 72 X 6KTDA32 976.10 Ea. 1.0 48 24 72 X 6KTDA42 1040.75 Ea. 201.0 Patriot Turnout Lockers - Welded All-Welded models include integral 4" base. (No Doors) " deep Hat Shelf. 1-Wide. 76 X 6WTDA84C 999.60 Ea. 84.0 24 76 X 6WTDA04C 1070. Ea. 104.0 30 76 X 6WTDA14C 13.10 Ea. 116.0 36 76 X 6WTDA24C 12.50 Ea. 131.0 24 24 76 X 6WTDA00C 11.40 Ea. 1.0 30 24 76 X 6WTDA10C 36.10 Ea. 136.0 36 24 76 X 6WTDA20C 44.65 Ea. 1.0 42 24 76 X 6WTDA30C 1361.60 Ea. 166.0 48 24 76 X 6WTDA40C 1378. Ea. 1.0 21" deep Hat Shelf. 1-Wide. 24 76 X 6WTDA82C 1067.80 Ea. 104.0 24 24 76 X 6WTDA02C 13.10 Ea. 5.0 30 24 76 X 6WTDAC 39.05 Ea. 140.0 36 24 76 X 6WTDA22C 48.40 Ea. 6.0 42 24 76 X 6WTDA32C 1366.20 Ea. 172.0 48 24 76 X 6WTDA42C 1384.05 Ea. 201.0 Patriot Accessory Note: Patriot accessories are designed for attachment on site during locker assembly and installation. On welded Patriot models, only the hat shelf will be factory installed. This is done to optimize paint coverage and facilitate interior configuration changes if needed. Patriot Locker Accessories Center Partition Punched for addition of Half Shelves. Note: 58" high partition goes from hat shelf to locker bottom. 45" high goes from hat shelf to optional bottom shelf at " from the bottom. 45 6CPX270C 73. Ea. 13.3 58 6CPX269C 93.25 Ea. 16.5 21 45 6CPX301C 79.95 Ea. 17.9 21 58 6CPX300C 98.80 Ea. 21.9 Penco Products Inc. 25

Full Width Metal Bottom Shelf Required for drawers and/or 45" high Center Partition (punched for partition). 6SHX695C 49.05 Ea. 6.4 24 6SHX575C 54.00 Ea. 5.8 30 6SHX576C 56.50 Ea. 9.5 36 6SHX577C 59.75 Ea. 11.0 24 6SHX696C 55.50 Ea. 8.0 24 24 6SHX530C 64.20 Ea. 11.0 30 24 6SHX531C 71.80 Ea..8 36 24 6SHX532C 105.85 Ea. 17.0 42 24 6SHX533C 1.00 Ea. 19.6 48 24 6SHX534C 9.20 Ea. 21.6 Full Width Intermediate Shelf Punched for Center Partition. Face is NOT punched for number plate. 6SHX700C 32.95 Ea. 5.5 24 6SHX708C 44.70 Ea. 6.5 30 6SHX709C 57.60 Ea. 8.0 36 6SHX710C 61. Ea. 9.5 42 6SHX803C 65.85 Ea. 11.0 48 6SHX804C 76.45 Ea..5 21 6SHX699C 42.35 Ea. 6.4 24 21 6SHX703C 65.85 Ea. 9.7 30 21 6SHX704C 72.90 Ea..0 36 21 6SHX705C 77.60 Ea. 14.0 42 21 6SHX706C 83.50 Ea. 16.8 48 21 6SHX707C 89.40 Ea. 19.2 Half Shelves (For use with Center Partition. Select depth to match partition.) 9 6SHX697C 26.95 Ea. 2.7 6SHX521C 28.85 Ea. 3.3 6SHX522C 28.20 Ea. 4.0 6SHX523C 30.25 Ea. 4.8 21 6SHX524C 33.40 Ea. 5.5 24 6SHX525C 43.40 Ea. 6.3 9 21 6SHX698C 31.75 Ea. 3.6 21 6SHX561C 32.95 Ea. 5.4 21 6SHX562C 35.30 Ea. 6.4 21 6SHX563C 41. Ea. 6.4 21 21 6SHX564C 51.75 Ea. 9.3 24 21 6SHX565C 52.90 Ea. 10.4 Foot Locker Not for use with partition. Accepts padlock (must be ordered separately). 6ACXHK58H 241.55 Ea..4 24 6ACXHK90H 273.45 Ea. 16.0 30 6ACXHK91H 290.85 Ea. 21.0 36 6ACXHK92H 306. Ea. 24.0 24 6ACXHK59H 235.20 Ea. 13.0 24 24 6ACXAB93H 242. Ea..0 30 24 6ACXAB94H 261.30 Ea. 23.0 36 24 6ACXAB95H 278.00 Ea. 28.0 42 24 6ACXAB96H 306.70 Ea. 33.0 48 24 6ACXAB97H 340.30 Ea. 38.0 Security Box For placement on top shelf only. Lock must be ordered separately. 24" wide model includes full width " deep interior shelf. Select depth to match hat shelf depth. 6ACXAB98H 107. Ea. 9.0 21 6ACXHM53H 117.60 Ea. 9.6 24 6ACXAB99H 2.40 Ea. 20.3 24 21 6ACXHM54H 135.25 Ea..2 Patriot Gear & Turnout Locker Accessories Drawer Units: " wide Patriot Lockers ONLY Lock must be ordered separately - see Lock Application Table. The following wide drawer units are ONLY used when ordering an wide Patriot locker and one drawer unit is required. If a 45 high Center Partition & Metal Bottom Shelf are used, select the high drawer. Must be ordered with a Full Metal Bottom Shelf. 6ACXHN70C 828.40 Ea. 39.0 24 6ACXHN10C 900.90 Ea. 49.0 6ACXHN80C 873.80 Ea. 39.8 24 6ACXHN20C 9.00 Ea. 53.0 Drawer Units: 36" & 42" wide Patriot Lockers The following wide drawer units are ONLY used when ordering a 36 wide Patriot locker and either one or two drawer units are required, OR when combining with a 24 wide drawer in a 42 wide locker. A single wide drawer can be used in either of these lockers if desired. If a 45 high Center Partition & Metal Bottom Shelf are used, select the high drawer. Must be ordered with a Full Metal Bottom Shelf. 6ACXFF82C 868.45 Ea. 39.0 24 6ACXFF60C 889.75 Ea. 49.0 6ACXFF87C 745.95 Ea. 39.8 24 6ACXFF20C 922.30 Ea. 53.0 Drawer Units: 24", 30", 42" & 48" wide Patriot Lockers 48 wide drawer units consist of two 24 wide drawers. A 24 wide drawer can be combined with an wide drawer (above) in a 42 wide Patriot locker. If a 45 high Center Partition & Metal Bottom Shelf are used, select the high drawer. Must be ordered with a Full Metal Bottom Shelf. 24 6ACXFF83C 876.50 Ea. 45.8 30 6ACXFF84C 883.45 Ea. 54.4 24 24 6ACXFF61C 894.20 Ea. 56.0 30 24 6ACXFF62C 966.50 Ea. 66.0 24 6ACXFF88C 871.90 Ea. 45.0 30 6ACXFF89C 875.25 Ea. 54.0 24 24 6ACXFF21C 900.80 Ea. 61.0 30 24 6ACXFF22C 1011.20 Ea. 72.0 Drawer Dividers- 2 required for hanging file folder use. Fits in drawer parallel with front of locker. 6ACXAB80C 25.55 Ea. 2.5 24 6ACXAB81C 29.40 Ea. 3.4 30 6ACXAB82C 34.55 Ea. 4.6 6ACXAB83C 28.85 Ea. 3.3 24 6ACXAB84C 33.75 Ea. 4.4 30 6ACXAB85C 40.70 Ea. 5.8 Document Sleeve 9.5 3 8 6ACXAB32C 32.35 Ea. 3.0 3 8 6ACXFF54C 34.00 Ea. 4.0 Parachute / Body Armor Rack 6ACXAB33C 247.05 Ea. 11.0 Acrylic Mirror With adhesive back; 1/8" thick. 6 8 96370 14.90 Ea. 0.6 Cell Phone / Key Tray The Cell Phone/Key Tray can be attached to the Center Partition or onto the 24 wide Security Box door in pre-punched holes or by using the Accessory Mounting Plate. There are also pre-punched holes in the sides, half way between the standard top shelf and the top of the locker that could be used to mount the tray if they are not being used for other accessories. If none of these options are acceptable field drilling may be required. 8 2 60830H 20.65 Ea. 0.5 26 Penco Products Inc.

Patriot Gear & Turnout Locker Accessories Heavy Duty Coat Hook - 5/16" thick aluminum 7/8 2-1/4 3 6ACXAB37H 46.20 Ea. 0.1 Coat Rod -1" Diameter, Chrome Plated Includes light gray brackets for mounting under intermediate shelf. 9 6ACXHM50H 60.60 Ea. 3.8 6ACXAB38H 60.60 Ea. 4.0 6ACXAB39H 60.60 Ea. 4.3 6ACXAB40H 60.60 Ea. 4.8 21 6ACXAB41H 60.60 Ea. 4.5 24 6ACXAB42H 60.60 Ea. 6.3 30 6ACXAB43H 74.00 Ea. 7.3 36 6ACXAB44H 74.00 Ea. 8.3 42 6ACXAB45H 94.10 Ea. 8.8 48 6ACXAB46H 94.10 Ea. 9.3 Garment Separator Replaces coat rod. 2 6ACXFF00H 17.40 Ea. 0.9 2 6ACXFF01H 17.90 Ea. 1.1 2 6ACXFF02H.30 Ea. 1.3 21 2 6ACXFF03H.80 Ea. 1.5 24 2 6ACXFF04H 19.25 Ea. 1.7 30 2 6ACXFF05H 20.30 Ea. 2.1 36 2 6ACXFF06H 21.20 Ea. 2.6 42 2 6ACXFF07H 22.20 Ea. 3.0 48 2 6ACXFF08H 23. Ea. 3.4 Boot Tray Rests on bottom of locker. 14 6ACXFF09H 59.35 Ea. 2.5 Accessory Mounting Plate Used for attaching accessories such as document sleeves, extra hooks or cell phone tray to the inside of the left side locker door without drilling through the door face. 24 6ACXFF10H 46.00 Ea. 5.7 24 6ACXFF11H 49.80 Ea. 7.1 24 6ACXFFH 55.80 Ea. 8.4 21 24 6ACXFF13H 59.90 Ea. 9.7 24 24 6ACXFF14H 66.40 Ea. 11.0 Hardwood Bench Seat Not for use with partition. 6RQ1317BH 384.10 Ea. 11.3 24 6RQ1305BH 384.10 Ea..0 30 6RQ1306BH 384.10 Ea..8 36 6RQ1307BH 263.90 Ea. 22.5 24 6RQ13BH 3.90 Ea..0 24 24 6RQ32BH 199.40 Ea. 20.0 30 24 6RQ33BH 435.75 Ea. 25.0 36 24 6RQ34BH 302.95 Ea. 30.0 42 24 6RQ35BH 360.40 Ea. 35.0 48 24 6RQ36BH 377.35 Ea. 40.0 Metal Seat Only Not for use with partitions. 6ACXHM51H 69.30 Ea..2 24 6ACXHK97AH 84.40 Ea. 13.5 30 6ACXHK98AH 94.50 Ea..0 36 6ACXHK99AH 108.35 Ea. 16.5 24 6ACXHM52H 88.20 Ea. 14.8 24 24 6ACXFF49AH 145.70 Ea. 23.0 30 24 6ACXFF50AH 8.30 Ea. 28.5 36 24 6ACXFF51AH 171.25 Ea. 33.7 42 24 6ACXFF52AH 4.20 Ea. 38.9 48 24 6ACXFF53AH 197.20 Ea. 44.1 Penco Products Inc. 27

Patriot Duty Locker Introduction Patriot Duty lockers feature fully equipped interiors with preconfigured compartments and additional private storage designed for the needs of law enforcement and security professionals. Patriot Duty lockers are available in KD construction (Knocked Down) and in Welded construction. Basic locker frame heights are 60" and 72". With " high drawer bases, the overall heights are 78" and 90". No legs are available, however welded models are available with an integral 4" high 14 gauge channel base & bottom, providing overall heights of 64" and 76". All Duty Lockers Include the Following Standard Equipment: One-wide construction Full width hat shelf " from the top with round perforations over the garment area Partition with a nominal 10" wide lockable compartment and additional shelf Heavy duty 1" diameter, chrome plated coat rod on the garment side (brackets are light gray) 2 heavy duty coat hooks mounted on the back on the garment side Double prong hook mounted underneath the lockable compartment Cremone-style turn handle - can be locked with a built-in lock or a padlock Double doors on 24" wide models and single doors on " wide models Continuous hinges welded to the doors and riveted to the bodies Knockouts to accommodate a single duplex receptacle on the locker top Environmentally friendly powder coat finish. Two-tone finishes are available at no charge, assuming use of standard Penco colors. Any request must be accompanied by a clear description of the combination desired. Steel Gauges 14 gauge louvered doors and 16 gauge solid sides 16 gauge top, shelves and partition; Top punched with slots to facilitate airflow Welded models with 4" high channel base: 14 gauge integral channel base & bottom; 16 gauge bottom on all other models No Charge Locker Options: Classic III or Defiant handle on " wide models Single door on 24" models with turn handle, Classic III or Defiant II handle Diamond perforations, mini louvers or solid doors Diamond perforated sides Drawer Base Seating Options: "Per Frame" hardwood sections as shown under accessories Must be ordered separately Bulk lengths of hardwood locker room benches, ordered from the standard locker price book and field cut Bulk lengths of hardwood locker room benches, detailed using the layout drawings and quoted separately Alternative seating material sourced by, and the responsibility of, the purchaser. (1.25" thick max) NOTE: Drawers function independently of the locker section. Order drawer locks separately. Requested features not listed as standard equipment must be clearly identified on the purchase order. Most Patriot Duty accessories are NOT designed for use on Patriot Gear and Turnout lockers. Patriot 24" wide Duty Locker with drawer base, wood bench (optional, order separately) and twotone finish. Patriot " wide Duty Locker with drawer base and wood bench (optional, order separately). 28 Penco Products Inc.

Patriot Duty Lockers & Duty Accessories Patriot Duty Lockers - KD With " H Drawer Base. 1-Wide. (SINGLE Door with Cremone Turn Handle) 24 60/78 X 64KD2478 2533.10 Ea. 227.0 24 72/90 X 64KD2490 2674.20 Ea. 249.0 With " H Drawer Base. 1-Wide. (Double Doors with Cremone Turn Handle) 24 24 60/78 XY 64KD242478 2560. Ea. 269.0 24 24 72/90 XY 64KD242490 2795.35 Ea. 293.0 No Legs. 1-Wide. (SINGLE Door with Cremone Turn Handle) 24 60 X 64KN2460 19.55 Ea. 139.0 24 72 X 64KN2472 1300.65 Ea. 161.0 No Legs. 1-Wide. (Double Doors with Cremone Turn Handle) 24 24 60 XY 64KN242460 46.55 Ea. 161.0 24 24 72 XY 64KN242472 1482.95 Ea. 5.0 Patriot Duty Lockers - Welded With " H Drawer Base. 1-Wide. (SINGLE Door with Cremone Turn Handle) 24 60/78 X 64WD2478C 2722.45 Ea. 227.0 24 72/90 X 64WD2490C 2921.20 Ea. 249.0 With " H Drawer Base. 1-Wide. (Double Doors with Cremone Turn Handle) 24 24 60/78 XY 64WD242478C 3047.00 Ea. 269.0 24 24 72/90 XY 64WD242490C 3148. Ea. 293.0 No Legs. 1-Wide. (SINGLE Door with Cremone Turn Handle) 24 60 X 64WN2460C 1374.75 Ea. 139.0 24 72 X 64WN2472C 1464.10 Ea. 161.0 No Legs. 1-Wide. (Double Doors with Cremone Turn Handle) 24 24 60 XY 64WN242460C 25.25 Ea. 161.0 24 24 72 XY 64WN242472C 00.45 Ea. 5.0 4" High Integral Channel Base. 1-Wide. (SINGLE Door with Cremone Turn Handle) 24 64 X 64WCB2464C 1419.45 Ea. 144.0 24 76 X 64WCB2476C 07.65 Ea. 166.0 4" High Integral Channel Base. 1-Wide. (Double Doors with Cremone Turn Handle) 24 24 64 XY 64WCB242464C 80.55 Ea. 166.0 24 24 76 XY 64WCB242476C 55.75 Ea. 191.0 Duty Locker Accessories Side Shelf (Mounts to the left of the interior divider.) 10 21 6SHX297C 37.80 Ea. 3.8 Acrylic Mirror With adhesive back; 1/8" thick. 6 8 96370 14.90 Ea. 0.6 Cell Phone / Key Tray The Cell Phone/Key Tray can be attached to the Center Partition or onto the 24 wide Security Box door in pre-punched holes or by using the Accessory Mounting Plate. There are also pre-punched holes in the sides, half way between the standard top shelf and the top of the locker that could be used to mount the tray if they are not being used for other accessories. If none of these options are acceptable field drilling may be required. 8 2 60830H 20.65 Ea. 0.5 Name Card Holder Size shown is card size. NOTE: Add $2.25 each to punch holeds in door for attaching. 2-3/4 1-1/4 9446H 8.10 Ea. 0.2 Drawer Divider (Two required for hanging file use.) 64DDC 30.45 Ea. 5.0 24 64DD24C 40.60 Ea. 6.8 Boot Tray Rests on bottom of locker. Fits 24" or wider Duty locker. 14 6ACXFF09H 59.35 Ea. 2.5 Heavy Duty Coat Hook - 5/16" thick aluminum 7/8 2-1/4 3 6ACXAB37H 46.20 Ea. 0.1 Individual Hardwood Seat Mounts to Drawer Base. Wood tone will vary between benches. 9-1/2 1-1/4 6RQ42 224. Ea. 6.0 24 9-1/2 1-1/4 6RQ0575 132.95 Ea. 8.0 Document Sleeve 9.5 3 8 6ACXAB32C 32.35 Ea. 3.0 3 8 6ACXFF54C 34.00 Ea. 4.0 Please Note: Patriot accessories are designed for attachment on site during locker assembly and installation. On welded Patriot models, only the hat shelf will be factory installed. This is done to optimize paint coverage and facilitate interior configuration changes if needed. Penco Products Inc. 29

Rapid Response Duffel Locker TM When Every Second Counts - Rapid Response Duffel Lockers are sized to fit pre-loaded and oversized TA-50 duffel bags and backpacks and cases. These lockers are available in 2 Tier in 72, 78 and 84 high, 3 Tier in 72, 78 and 84 high and 4 Tier in 72, 78 and 84 high. The Rapid Response Duffel Locker features: Knocked Down construction, shipped unassembled, assembly available No legs or bases are available One-wide construction Number plates Environmentally friendly powder coat finish Individually locked compartments for quick user access Sized to fit pre-loaded and oversized TA-50 duffel bags and backpacks and cases Lockers will be provided as individual units for ease of mobility and relocation as the mission demands Heavy duty 14 gauge doors with continuous hinges,16 gauge body, gauge back Heavy duty Cremone handle with 3-point latching Door and Frames 30, 36, 42 and 48 wide, the doors will ship separate from frame and need to be field installed with rivets On 48 wide lockers, the backs will be supplied as two 24 wide backs Note: when ordering, each catalog number is based on a specific division and door ventilation Cremone Turn Handle doors have a 3-point latching system utilizing 3/8 latching rods that engage the top and bottom door frames, and a 1/8 thick center latch that engages at the door frame. 2 Tier (Solid Division, Solid Door) 24 24 72 6KF2A2472 1463.87 Frm. 165.0 LPP 30 24 72 6KF2A3072 28.03 Frm. 5.0 LPP 36 24 72 6KF2A3672 1693.79 Frm. 205.0 LPP 42 24 72 6KF2A4272 1758.35 Frm. 225.0 LPP 48 24 72 6KF2A4872 2062.34 Frm. 245.0 LPP 24 24 78 6KF2A2478 02.39 Frm. 2.0 LPP 30 24 78 6KF2A3078 72.59 Frm. 198.0 LPP 36 24 78 6KF2A3678 1753.11 Frm. 223.0 LPP 42 24 78 6KF2A4278 1920.51 Frm. 248.0 LPP 48 24 78 6KF2A4878 2107.07 Frm. 274.0 LPP 24 24 84 6KF2A2484 1609.80 Frm. 3.0 LPP 30 24 84 6KF2A3084 1678. Frm. 209.0 LPP 36 24 84 6KF2A3684 60.46 Frm. 235.0 LPP 42 24 84 6KF2A4284 1963.59 Frm. 262.0 LPP 48 24 84 6KF2A4884 2239.20 Frm. 288.0 LPP 2 Tier (Solid Division, Louver Door) 24 24 72 6KF2B2472 19.49 Frm. 165.0 LPP 30 24 72 6KF2B3072 83.70 Frm. 5.0 LPP 36 24 72 6KF2B3672 1749.40 Frm. 205.0 LPP 42 24 72 6KF2B4272 13.96 Frm. 225.0 LPP 48 24 72 6KF2B4872 2117.95 Frm. 245.0 LPP 24 24 78 6KF2B2478 58.01 Frm. 2.0 LPP 30 24 78 6KF2B3078 1628.21 Frm. 198.0 LPP 36 24 78 6KF2B3678 10.37 Frm. 223.0 LPP 42 24 78 6KF2B4278 68.77 Frm. 248.0 LPP 48 24 78 6KF2B4878 2162.74 Frm. 274.0 LPP 24 24 84 6KF2B2484 1665.47 Frm. 3.0 LPP 30 24 84 6KF2B3084 1733.73 Frm. 209.0 LPP 36 24 84 6KF2B3684 1916.07 Frm. 235.0 LPP 42 24 84 6KF2B4284 2019.20 Frm. 262.0 LPP 48 24 84 6KF2B4884 2294.81 Frm. 288.0 LPP 2 Tier (Solid Division, Diamond Door) 24 24 72 6KF2C2472 43.53 Frm. 165.0 LPP 30 24 72 6KF2C3072 1605.87 Frm. 5.0 LPP 36 24 72 6KF2C3672 1771.97 Frm. 205.0 LPP 42 24 72 6KF2C4272 38.01 Frm. 225.0 LPP 48 24 72 6KF2C4872 2141.99 Frm. 245.0 LPP 24 24 78 6KF2C2478 57.49 Frm. 2.0 LPP 30 24 78 6KF2C3078 1627.69 Frm. 198.0 LPP 36 24 78 6KF2C3678 09.86 Frm. 223.0 LPP 42 24 78 6KF2C4278 68.26 Frm. 248.0 LPP 48 24 78 6KF2C4878 2162.22 Frm. 274.0 LPP 2 Tier (Solid Division, Diamond Door) - cont. 24 24 84 6KF2C2484 1689.52 Frm. 3.0 LPP 30 24 84 6KF2C3084 1757.78 Frm. 209.0 LPP 36 24 84 6KF2C3684 1940.11 Frm. 235.0 LPP 42 24 84 6KF2C4284 2043.25 Frm. 262.0 LPP 48 24 84 6KF2C4884 2682.11 Frm. 288.0 LPP 2 Tier (Diamond Division, Solid Door) 24 24 72 6KF2D2472 1478.35 Frm. 165.0 LPP 30 24 72 6KF2D3072 42.56 Frm. 5.0 LPP 36 24 72 6KF2D3672 1708.32 Frm. 205.0 LPP 42 24 72 6KF2D4272 1772.82 Frm. 225.0 LPP 48 24 72 6KF2D4872 2076.81 Frm. 245.0 LPP 24 24 78 6KF2D2478 16.92 Frm. 2.0 LPP 30 24 78 6KF2D3078 87. Frm. 198.0 LPP 36 24 78 6KF2D3678 1767.64 Frm. 223.0 LPP 42 24 78 6KF2D4278 27.69 Frm. 248.0 LPP 48 24 78 6KF2D4878 21.60 Frm. 274.0 LPP 24 24 84 6KF2D2484 1638.92 Frm. 3.0 LPP 30 24 84 6KF2D3084 1707. Frm. 209.0 LPP 36 24 84 6KF2D3684 89.52 Frm. 235.0 LPP 42 24 84 6KF2D4284 1992.65 Frm. 262.0 LPP 48 24 84 6KF2D4884 2268.26 Frm. 288.0 LPP 2 Tier (Diamond Division, Louver Door) 24 24 72 6KF2E2472 33.96 Frm. 165.0 LPP 30 24 72 6KF2E3072 98. Frm. 5.0 LPP 36 24 72 6KF2E3672 1763.93 Frm. 205.0 LPP 42 24 72 6KF2E4272 28.43 Frm. 225.0 LPP 48 24 72 6KF2E4872 2132.48 Frm. 245.0 LPP 24 24 78 6KF2E2478 72.54 Frm. 2.0 LPP 30 24 78 6KF2E3078 1642.74 Frm. 198.0 LPP 36 24 78 6KF2E3678 24.90 Frm. 223.0 LPP 42 24 78 6KF2E4278 83.30 Frm. 248.0 LPP 48 24 78 6KF2E4878 2177.26 Frm. 274.0 LPP 24 24 84 6KF2E2484 1694.53 Frm. 3.0 LPP 30 24 84 6KF2E3084 1762.85 Frm. 209.0 LPP 36 24 84 6KF2E3684 1945.13 Frm. 235.0 LPP 42 24 84 6KF2E4284 2048.32 Frm. 262.0 LPP 48 24 84 6KF2F4884 26.52 Frm. 288.0 LPP 30 Penco Products Inc.

2 Tier (Diamond Division, Diamond Door) 24 24 72 6KF2F2472 58.06 Frm. 165.0 LPP 30 24 72 6KF2F3072 1620.34 Frm. 5.0 LPP 36 24 72 6KF2F3672 1786.50 Frm. 205.0 LPP 42 24 72 6KF2F4272 52.54 Frm. 225.0 LPP 48 24 72 6KF2F4872 26.52 Frm. 245.0 LPP 24 24 78 6KF2F2478 72.02 Frm. 2.0 LPP 30 24 78 6KF2F3078 1642.22 Frm. 198.0 LPP 36 24 78 6KF2F3678 24.39 Frm. 223.0 LPP 42 24 78 6KF2F4278 82.79 Frm. 248.0 LPP 48 24 78 6KF2F4878 2176.75 Frm. 274.0 LPP 24 24 84 6KF2F2484 17.58 Frm. 3.0 LPP 30 24 84 6KF2F3084 1786.89 Frm. 209.0 LPP 36 24 84 6KF2F3684 1969.17 Frm. 235.0 LPP 42 24 84 6KF2F4284 2072.36 Frm. 262.0 LPP 48 24 84 6KF2F4884 2711.17 Frm. 288.0 LPP 3 Tier (Solid Division, Solid Door) 24 24 72 6KF3A2472 1693.28 Frm. 165.0 LPP 30 24 72 6KF3A3072 1780.85 Frm. 5.0 LPP 36 24 72 6KF3A3672 1,940.23 Frm. 205.0 LPP 42 24 72 6KF3A4272 2061.65 Frm. 225.0 LPP 48 24 72 6KF3A4872 23.67 Frm. 245.0 LPP 24 24 78 6KF3A2478 71.68 Frm. 2.0 LPP 30 24 78 6KF3A3078 20.75 Frm. 198.0 LPP 36 24 78 6KF3A3678 28.46 Frm. 223.0 LPP 42 24 78 6KF3A4278 2198.23 Frm. 248.0 LPP 48 24 78 6KF3A4878 2690.26 Frm. 274.0 LPP 24 24 84 6KF3A2484 1919.43 Frm. 3.0 LPP 30 24 84 6KF3A3084 2062.22 Frm. 209.0 LPP 36 24 84 6KF3A3684 27.86 Frm. 235.0 LPP 42 24 84 6KF3A4284 2260.46 Frm. 262.0 LPP 48 24 84 6KF3A4884 2711.11 Frm. 288.0 LPP 3 Tier (Solid Division, Louver Door) 24 24 72 6KF3B2472 1776.70 Frm. 165.0 LPP 30 24 72 6KF3B3072 64.27 Frm. 5.0 LPP 36 24 72 6KF3B3672 2023.65 Frm. 205.0 LPP 42 24 72 6KF3B4272 2145.07 Frm. 225.0 LPP 48 24 72 6KF3B4872 2399.09 Frm. 245.0 LPP 24 24 78 6KF3B2478 1955.10 Frm. 2.0 LPP 30 24 78 6KF3B3078 2102.17 Frm. 198.0 LPP 36 24 78 6KF3B3678 2241.88 Frm. 223.0 LPP 42 24 78 6KF3B4278 2259.37 Frm. 248.0 LPP 48 24 78 6KF3B4878 2763.59 Frm. 274.0 LPP 24 24 84 6KF3B2484 2002.91 Frm. 3.0 LPP 30 24 84 6KF3B3084 2145.70 Frm. 209.0 LPP 36 24 84 6KF3B3684 2271.28 Frm. 235.0 LPP 42 24 84 6KF3B4284 2343.93 Frm. 262.0 LPP 48 24 84 6KF3B4884 2794.59 Frm. 288.0 LPP 3 Tier (Solid Division, Diamond Door) 24 24 72 6KF3C2472.76 Frm. 165.0 LPP 30 24 72 6KF3C3072 1900.34 Frm. 5.0 LPP 36 24 72 6KF3C3672 2059.72 Frm. 205.0 LPP 42 24 72 6KF3C4272 2203.48 Frm. 225.0 LPP 48 24 72 6KF3C4872 2435.16 Frm. 245.0 LPP 24 24 78 6KF3C2478 1991.17 Frm. 2.0 LPP 30 24 78 6KF3C3078 2138.23 Frm. 198.0 LPP 36 24 78 6KF3C3678 2277.95 Frm. 223.0 LPP 42 24 78 6KF3C4278 2295.44 Frm. 248.0 LPP 48 24 78 6KF3C4878 2799.66 Frm. 274.0 LPP 3 Tier (Solid Division, Diamond Door) - cont. 24 24 84 6KF3C2484 2038.97 Frm. 3.0 LPP 30 24 84 6KF3C3084 2175.56 Frm. 209.0 LPP 36 24 84 6KF3C3684 2307.35 Frm. 235.0 LPP 42 24 84 6KF3C4284 2380.00 Frm. 262.0 LPP 48 24 84 6KF3C4884 2830.66 Frm. 288.0 LPP 3 Tier (Diamond Division, Solid Door) 24 24 72 6KF3D2472 1707.75 Frm. 165.0 LPP 30 24 72 6KF3D3072 1795.33 Frm. 5.0 LPP 36 24 72 6KF3D3672 1954.76 Frm. 205.0 LPP 42 24 72 6KF3D4272 2077.89 Frm. 225.0 LPP 48 24 72 6KF3D4872 2330.14 Frm. 245.0 LPP 24 24 78 6KF3D2478 86.21 Frm. 2.0 LPP 30 24 78 6KF3D3078 2033.28 Frm. 198.0 LPP 36 24 78 6KF3D3678 2172.99 Frm. 223.0 LPP 42 24 78 6KF3D4278 22.76 Frm. 248.0 LPP 48 24 78 6KF3D4878 2694.70 Frm. 274.0 LPP 24 24 84 6KF3D2484 1948.55 Frm. 3.0 LPP 30 24 84 6KF3D3084 2091.28 Frm. 209.0 LPP 36 24 84 6KF3D3684 2216.92 Frm. 235.0 LPP 42 24 84 6KF3D4284 2289.52 Frm. 262.0 LPP 48 24 84 6KF3D4884 2740.23 Frm. 288.0 LPP 3 Tier (Diamond Division, Louver Door) 24 24 72 6KF3E2472 1791.23 Frm. 165.0 LPP 30 24 72 6KF3E3072 78.80 Frm. 5.0 LPP 36 24 72 6KF3E3672 2038. Frm. 205.0 LPP 42 24 72 6KF3E4272 29.60 Frm. 225.0 LPP 48 24 72 6KF3E4872 2413.62 Frm. 245.0 LPP 24 24 78 6KF3E2478 1969.63 Frm. 2.0 LPP 30 24 78 6KF3E3078 2116.70 Frm. 198.0 LPP 36 24 78 6KF3E3678 2256.41 Frm. 223.0 LPP 42 24 78 6KF3E4278 2273.90 Frm. 248.0 LPP 48 24 78 6KF3E4878 2778. Frm. 274.0 LPP 24 24 84 6KF3E2484 2031.97 Frm. 3.0 LPP 30 24 84 6KF3E3084 2174.76 Frm. 209.0 LPP 36 24 84 6KF3E3684 2300.34 Frm. 235.0 LPP 42 24 84 6KF3E4284 2372.99 Frm. 262.0 LPP 48 24 84 6KF3E4884 2823.65 Frm. 288.0 LPP 3 Tier (Diamond Division, Diamond Door) 24 24 72 6KF3F2472 27.29 Frm. 165.0 LPP 30 24 72 6KF3F3072 1914.87 Frm. 5.0 LPP 36 24 72 6KF3F3672 2074.25 Frm. 205.0 LPP 42 24 72 6KF3F4272 22.01 Frm. 225.0 LPP 48 24 72 6KF3F4872 2449.69 Frm. 245.0 LPP 24 24 78 6KF3F2478 2005.70 Frm. 2.0 LPP 30 24 78 6KF3F3078 22.76 Frm. 198.0 LPP 36 24 78 6KF3F3678 2292.48 Frm. 223.0 LPP 42 24 78 6KF3F4278 2309.97 Frm. 248.0 LPP 48 24 78 6KF3F4878 2814.19 Frm. 274.0 LPP 24 24 84 6KF3F2484 2068.03 Frm. 3.0 LPP 30 24 84 6KF3F3084 2204.62 Frm. 209.0 LPP 36 24 84 6KF3F3684 2336.41 Frm. 235.0 LPP 42 24 84 6KF3F4284 2409.06 Frm. 262.0 LPP 48 24 84 6KF3F4884 2859.72 Frm. 288.0 LPP Penco Products Inc. 31

4 Tier (Solid Division, Solid Door) 24 24 72 6KF4A2472 29.29 Frm. 165.0 LPP 30 24 72 6KF4A3072 2269.23 Frm. 5.0 LPP 36 24 72 6KF4A3672 2433.62 Frm. 205.0 LPP 42 24 72 6KF4A4272 2507.86 Frm. 225.0 LPP 48 24 72 6KF4A4872 2862.68 Frm. 245.0 LPP 24 24 78 6KF4A2478 2246.89 Frm. 2.0 LPP 30 24 78 6KF4A3078 2373.16 Frm. 198.0 LPP 36 24 78 6KF4A3678 2561.65 Frm. 223.0 LPP 42 24 78 6KF4A4278 2647.35 Frm. 248.0 LPP 48 24 78 6KF4A4878 3009.52 Frm. 274.0 LPP 24 24 84 6KF4A2484 2349.61 Frm. 3.0 LPP 30 24 84 6KF4A3084 2455.54 Frm. 209.0 LPP 36 24 84 6KF4A3684 2682.62 Frm. 235.0 LPP 42 24 84 6KF4A4284 2820.51 Frm. 262.0 LPP 48 24 84 6KF4A4884 31.10 Frm. 288.0 LPP 4 Tier (Solid Division, Louver Door) 24 24 72 6KF4B2472 2160.57 Frm. 165.0 LPP 30 24 72 6KF4B3072 2381.31 Frm. 5.0 LPP 36 24 72 6KF4B3672 2531.51 Frm. 205.0 LPP 42 24 72 6KF4B4272 2619.89 Frm. 225.0 LPP 48 24 72 6KF4B4872 2974.76 Frm. 245.0 LPP 24 24 78 6KF4B2478 2358. Frm. 2.0 LPP 30 24 78 6KF4B3078 2484.44 Frm. 198.0 LPP 36 24 78 6KF4B3678 2672.93 Frm. 223.0 LPP 42 24 78 6KF4B4278 2758.63 Frm. 248.0 LPP 48 24 78 6KF4B4878 3065.13 Frm. 274.0 LPP 24 24 84 6KF4B2484 2453.28 Frm. 3.0 LPP 30 24 84 6KF4B3084 2577.95 Frm. 209.0 LPP 36 24 84 6KF4B3684 2805.03 Frm. 235.0 LPP 42 24 84 6KF4B4284 2942.86 Frm. 262.0 LPP 48 24 84 6KF4B4884 3303.45 Frm. 288.0 LPP 4 Tier (Solid Division, Diamond Door) 24 24 72 6KF4C2472 2288.66 Frm. 165.0 LPP 30 24 72 6KF4C3072 2429.40 Frm. 5.0 LPP 36 24 72 6KF4C3672 2593.79 Frm. 205.0 LPP 42 24 72 6KF4C4272 2668.03 Frm. 225.0 LPP 48 24 72 6KF4C4872 3022.85 Frm. 245.0 LPP 24 24 78 6KF4C2478 2406.27 Frm. 2.0 LPP 30 24 78 6KF4C3078 2532.54 Frm. 198.0 LPP 36 24 78 6KF4C3678 2719.94 Frm. 223.0 LPP 42 24 78 6KF4C4278 3066.95 Frm. 248.0 LPP 48 24 78 6KF4C4878 3168.89 Frm. 274.0 LPP 24 24 84 6KF4C2484 2506. Frm. 3.0 LPP 30 24 84 6KF4C3084 2630.85 Frm. 209.0 LPP 36 24 84 6KF4C3684 2857.93 Frm. 235.0 LPP 42 24 84 6KF4C4284 3131.93 Frm. 262.0 LPP 48 24 84 6KF4C4884 3356.35 Frm. 288.0 LPP 4 Tier (Diamond Division, Solid Door) 24 24 72 6KF4D2472 2143.82 Frm. 165.0 LPP 30 24 72 6KF4D3072 2284.56 Frm. 5.0 LPP 36 24 72 6KF4D3672 2448.95 Frm. 205.0 LPP 42 24 72 6KF4D4272 2523.19 Frm. 225.0 LPP 48 24 72 6KF4D4872 2878.01 Frm. 245.0 LPP 24 24 78 6KF4D2478 2261.42 Frm. 2.0 LPP 30 24 78 6KF4D3078 2387.69 Frm. 198.0 LPP 36 24 78 6KF4D3678 2576. Frm. 223.0 LPP 42 24 78 6KF4D4278 2661.88 Frm. 248.0 LPP 48 24 78 6KF4D4878 3024.05 Frm. 274.0 LPP 4 Tier (Diamond Division, Solid Door) - cont. 24 24 84 6KF4D2484 2381.58 Frm. 3.0 LPP 30 24 84 6KF4D3084 2487.50 Frm. 209.0 LPP 36 24 84 6KF4D3684 2714.59 Frm. 235.0 LPP 42 24 84 6KF4D4284 2852.48 Frm. 262.0 LPP 48 24 84 6KF4D4884 3213.07 Frm. 288.0 LPP 4 Tier (Diamond Division, Louver Door) 24 24 72 6KF4E2472 2175.10 Frm. 165.0 LPP 30 24 72 6KF4E3072 2387.86 Frm. 5.0 LPP 36 24 72 6KF4E3672 2546.04 Frm. 205.0 LPP 42 24 72 6KF4E4272 2634.42 Frm. 225.0 LPP 48 24 72 6KF4E4872 2989.29 Frm. 245.0 LPP 24 24 78 6KF4E2478 2372.71 Frm. 2.0 LPP 30 24 78 6KF4E3078 2498.97 Frm. 198.0 LPP 36 24 78 6KF4E3678 2687.46 Frm. 223.0 LPP 42 24 78 6KF4E4278 2773.16 Frm. 248.0 LPP 48 24 78 6KF4E4878 3079.66 Frm. 274.0 LPP 24 24 84 6KF4E2484 2485.25 Frm. 3.0 LPP 30 24 84 6KF4E3084 2609.91 Frm. 209.0 LPP 36 24 84 6KF4E3684 2837.00 Frm. 235.0 LPP 42 24 84 6KF4E4284 2974.83 Frm. 262.0 LPP 48 24 84 6KF4E4884 3335.41 Frm. 288.0 LPP 4 Tier (Diamond Division, Diamond Door) 24 24 72 6KF4F2472 2303.19 Frm. 165.0 LPP 30 24 72 6KF4F3072 2435.95 Frm. 5.0 LPP 36 24 72 6KF4F3672 2608.26 Frm. 205.0 LPP 42 24 72 6KF4F4272 2682.51 Frm. 225.0 LPP 48 24 72 6KF4F4872 3037.38 Frm. 245.0 LPP 24 24 78 6KF4F2478 2420.80 Frm. 2.0 LPP 30 24 78 6KF4F3078 2547.07 Frm. 198.0 LPP 36 24 78 6KF4F3678 2734.47 Frm. 223.0 LPP 42 24 78 6KF4F4278 3081.48 Frm. 248.0 LPP 48 24 78 6KF4F4878 33.42 Frm. 274.0 LPP 24 24 84 6KF4F2484 2538. Frm. 3.0 LPP 30 24 84 6KF4F3084 2662.81 Frm. 209.0 LPP 36 24 84 6KF4F3684 2889.90 Frm. 235.0 LPP 42 24 84 6KF4F4284 3165.35 Frm. 262.0 LPP 48 24 84 6KF4F4884 3388.31 Frm. 288.0 LPP 32 Penco Products Inc.

Locker Features and Options Penco LOCKERS AT A GLANCE - Availability of Features & Options on 8 basic Penco locker types. Vanguard Knocked Down Guardian Invincible II Rapid Response KD or Welded Welded Construction Stadium Patriot All-Welded Angle Iron Legs and Bases 6 Legs S S S N/A N/A N/A N/A N/A 4 Legs N/A N/A N/A N/A N/A N/A A N/A No Legs A A A S S S S S Front Base A A A N/A N/A N/A N/A N/A End Base A A A N/A N/A N/A N/A N/A Zee Bases A A A N/A N/A N/A N/A N/A Channel Base, Integral N/A N/A N/A N/A W W A A Handles Vanguard Handle S N/A N/A N/A N/A N/A N/A N/A Recessed Handle for Multi-Point Latch A S S N/A N/A A (24"w door) S A Defiant II Single Point Latch (Recessed) N/A A* A N/A N/A A (24"w door) A A Friction Catch Door Pull (Box Lockers) S N/A S N/A A S (Box) S S Cremone Turn Handle (3 Point Latch) N/A A* A S N/A S (Gear/Duty) A A Spring Loaded Box Locker Latch N/A N/A A N/A N/A N/A A N/A Doors and Ventilation Standard Louvers S A A A N/A S (Gear/Duty) A A Full Louvers A A A A N/A A A A Mini Louvers A A A A Foot Locker A A A No Louvers-No Perforations in the Door A S A A N/A A A A Diamond-Shaped Door Perforations N/A A* S A N/A A (Gear/Duty) S S Visual Perforations in Door (5/8 w x 1-1/8 h) A N/A N/A N/A N/A N/A N/A N/A Double Pan Door with Single Point Latch N/A ** ** N/A N/A ** ** ** Door Ventilation Slots Top & Bottom Flange S S S S N/A S (Gear) S S Fire Extinguisher Door A A A N/A N/A N/A A A Waste Bin Door A A A N/A N/A N/A A A Sound-Dampening Panel (Louvers N/A) A A N/A N/A N/A N/A N/A N/A Heavy 14 Gauge Door N/A A S S N/A S (Gear) S S 2" high 5 Knuckle Hinges S S S N/A N/A N/A N/A N/A 3 high 5 Knuckle Butt Hinges N/A N/A N/A N/A N/A N/A N/A A Continuous Hinge A A A S Box, Foot Locker S (Gear/Duty) S S Padlock Strike Plate A N/A A N/A S A A A Miscellaneous Center Partitions A A A N/A N/A A A N/A Extra Shelves A A A N/A N/A A A A Heavy Gauge Bottom (16 Ga.) A A S S S S S S Heavy Gauge Bottom (14 Ga.) N/A N/A N/A N/A N/A W+ N/A A Round Perforations in Sides A A N/A N/A N/A N/A N/A N/A Diamond Shaped Perforations in Sides N/A N/A S A S S (Gear/ S S*** Expanded Metal Sides N/A N/A N/A N/A N/A N/A N/A A Individual Sloping Tops A A N/A N/A N/A N/A N/A N/A Continuous Slope Hoods A A A A A A A A Slope Top Kits A A N/A N/A N/A N/A N/A N/A Factory Assembly A A A A A A S S Recessed Trim A A A A A A A A Finished End Panel A A A A A A A A Heavy Gauge End Panel (16 ga.) A A S S S S S A Handicap Lockers A A A N/A N/A N/A A A Packing House Legs A A N/A N/A N/A N/A N/A N/A Patriot Accessories (see Patriot section) N/A N/A N/A N/A N/A A N/A N/A S = Standard W = All Welded Models Only A = Available Options N/A = Not Available + = Standard with Channel Base * Available with Optional 14 gauge door only ** Available with Defiant II Option Only ***14 Gauge Steel Penco Products Inc. 33

Ventilation Options and Specialty Doors Vanguard (Louvered Doors Standard) & Guardian Lockers (Solid Doors Standard) Visual Perforations - Doors Only: Visual perforations in doors only provide a high degree of ventilation and allow for easy visual inspection of contents. Rectangular punchings measure 5/8 wide x 1-1/8 high. This type of perforation is available on all Vanguard and standard Guardian lockers. Pattern and number of perforations vary by door size and handle type. NOT available on Guardian Plus or Guardian Defiant II. Visual Perforation Pricing - Doors Only Frame Width -> 24 Price Per Frame 1 Tier (except 24 wide Double Door) 5.05 5.70 6.30 8.35 2 Tier 6.30 7.55 8.80 10.30 3 Tier 8.50 10.40.30 4, 5 & 6 Tier.10.90 22.45 Duplex (Both Doors) 11.10 Two Person - Lower Doors Only 11.10 11.10 Two Person - All 4 Doors 13.90 13.90 (NOT recommended for all 4 doors on 2 Person due to potential security problem) Round Perforations for Body Parts: (Backs, Divisions [sides], Tops, Bottoms & Shelves) Perforations consist of a group of 42 holes with 1/2 diameters, spaced on 1 centers. Size of a standard group of 42 holes is 5-1/2 wide by 6-1/2 high. Price is for Divisions or Backs up to 21 deep or wide. For Divisions and Backs together, double the price per frame. Applies only to lockers with 24 ga. body parts. Round Perforation Pricing for DIVISIONS and BACKS 5 groups on 60 high; 6 groups on 72 high. Price Per Frame 1, 2, 3, 4, 5 & 6 Tier 5.60 Two person & Duplex 8.95 Round Perforations for TOPS, BOTTOMS or SHELVES Price per Piece (up to " wide) 1.00 Price per Piece (24" wide) 2.00 Mini Louvers - Doors Only: Provides ventilation and blocks visibility of contents. Protrusions are on the inside of the locker door; 5/8" wide x 1/4" high. Pattern and number of perforations vary by door size and handle type. Mini Louver Pricing - Doors Only Frame Width -> 24 Price Per Frame 1 Tier 1.30 2.00 2.60 3. 2 Tier 1.30 2.05 2.65 3.25 3, 4, 5 & 6 Tier 1.45 2. 2.90 n/a Pricing for Standard Louver Variations One Group or NO Louvers For Standard Vanguard Lockers Only $5.60 per frame Full Louvers (1 & 2 Tier Only). This option is generally provided as two extended patterns of louvers per door. 1 Tier: Add $3.50 per frame 2 Tier: Add $4.85 per frame To Add Standard Louvers to Guardian Plus & Guardian Defiant II (14 ga. doors) Add $2.00 per door Fire Extinguisher & Waste Bin Doors: For KD Vanguard and Guardian lockers, & wide, 1Tier & 2 Tier only ( Minimum width for Fire Ext. Door with Recessed Handle). Add the following extras to the price & weight of the locker: Fire Extinguisher & Waste Bin Door Pricing Price Wt. Fire Extinguisher Door for locker (with cutout & glass included) 8.00 3 Waste Bin Door for Locker (waste chute included, waste container not included) 3.70 8 Note: For All-Welded & Invincible II Lockers, see next page. QUIET SOUND DAMPENING PANS Prices for solid/louvered doors ONLY. Not for use with Safe-O-Mat locks. Add to 48", 60" & 72" high doors 13.75 per door Add to 30" & 36" high doors 8.65 per door Add to 20" & 24" high doors 7.30 per door 34 Penco Products Inc.

Finish Options Colors, Finishes and Electrogalvanizing for Lockerss QuickShip Select types & sizes of Vanguard (Ships within 5 working days) KD LOCKERS Vanguard, Guardian, Invincible, Stadium, Patriot WELDED LOCKERS Stadium, Patriot, All-Welded, Angle Iron * Locker Accessories Basket Racks Powder Coat Standard Standard Standard Standard Standard Available Colors Two Tone Colors (Contrasting Doors & Frames) PowderCoatPlus 2 Mil Thick Paint X-Off Anti Graffiti Paint Specialty Coatings or Custom Colors Common Color Body Parts Galvanneal (for bottoms or shelves only, see page 42) Ventilation Options, Etc. (continued) / Colors & Finishes Ventilation Options & Specialty Doors for: Invincible II, All-Welded & Angle Iron To Delete Diamond Perforations: For NO diamond perforations in sides and/or doors of Invincible II or All-Welded lockers, there is no additional charge, however clearly mark the order whether perforations are to be deleted from doors, sides or both. To Add Louvers: If diamond-shaped perforations have been deleted, standard louvers (same as Vanguard) can be added for no additional charge. To Perforate Locker Shelves: To Perforate Shelf or Intermediate Bottom with one group of 42 1/2 diameter holes: Add $1.50 per piece per size and type up to " wide. Add $3.00 per piece for 24" wide shelves. 028 Gray & 073 Champagne Not Available All 24 Colors All 24 Colors All 24 Colors No Extra Charge. Door frame can contrast with the door & body or the door can contrast with the rest of the locker. This is only when a total of two Penco standard colors are involved and does not include any type of color pattern. No Extra Charge. Door frame can contrast with the door & body or the door can contrast with the rest of the locker. This is only when a total of two Penco standard colors are involved and does not include any type of color pattern. * ANGLE IRON lockers must have continuous piano hinges for Two-Tone finish (no extra charge). Not Available 4% Up Charge 4% Up Charge Not Available % Up Charge % Up Charge Not Available 4% Up Charge % up Charge All 24 Colors Not Available 4% Up Charge Not Available SPI SPI SPI SPI Not Available Not Available No Extra Cost (By special request only) % Upcharge Positive Spring "Slam" Latch for 4, 5, 6, 8, and 9 Tier Lockers: Add $10.00 per door to price of frame for this latch. Utilizing this latch will change the door perforation pattern. Not available on Angle Iron. Mini Louvers: Same price per frame as "Mini Louvers" section for 'Vanguard & Guardian' lockers on previous page. Fire Extinguisher & Waste Bin Doors: For All-Welded & Invincible II Lockers with Fire Extinguisher and/or Waste Bin Doors see section above in 'Vanguard and Guardian Fire Extinguisher & Waste Bin Doors' for cost to upgrade doors. Not Available % Upcharge Note: on Angle Iron lockers, only the sheet steel is galvanized. Not Available % Upcharge SPI Not Available Not Available Penco Products Inc. 35

Touch Up Paint Touch Up Paint, Air Dry 4.5 oz. Spray Can Tawny Tan 970 25.60 Ea. 1.0 Gray Ash 97021 25.60 Ea. 1.0 Gray 97028 25.60 Ea. 1.0 Reflex Blue 97052 25.60 Ea. 1.0 Canvas 97054 25.60 Ea. 1.0 Shamrock 97055 25.60 Ea. 1.0 Sunburst 97056 25.60 Ea. 1.0 Nordic Purple 97058 25.60 Ea. 1.0 Champagne 97073 25.60 Ea. 1.0 Spray Green 97701 25.60 Ea. 1.0 Sagebrush Yellow 97710 25.60 Ea. 1.0 Lake Blue 977 25.60 Ea. 1.0 Mandarin Orange 97720 25.60 Ea. 1.0 Patriot Red 97722 25.60 Ea. 1.0 Light Putty 97723 25.60 Ea. 1.0 Burgundy 97736 25.60 Ea. 1.0 Cardinal Red 97767 25.60 Ea. 1.0 Marine Blue 97806 25.60 Ea. 1.0 Hunter Green 978 25.60 Ea. 1.0 Regal Blue 97822 25.60 Ea. 1.0 Slate Blue 97826 25.60 Ea. 1.0 January 97848 25.60 Ea. 1.0 Jet Black 97949 25.60 Ea. 1.0 Turquoise Teal 97952 25.60 Ea. 1.0 Gallon Cans GALLON 314.30 Ea. 10.0 0.33 oz. Paint Pens The metal barrel Paint Pens (0.33 oz.) with a valve activated chiseltip, ship from the Penco manufacturing plant in Hamilton, NC. Store recapped pens in a cool, dark area for optimal performance. Pens are recommended to be used on more visible areas like doors and frames. A minimum order of two (2) pens of the same color is required. Prices shown are as NET PRICE. Tawny Tan 2PEN0 10.00 NET Ea.1.0 Gray Ash 2PEN021 10.00 NET Ea.1.0 Gray 2PEN028 10.00 NET Ea.1.0 Reflex Blue 2PEN052 10.00 NET Ea.1.0 Canvas 2PEN054 10.00 NET Ea.1.0 Shamrock 2PEN055 10.00 NET Ea.1.0 Sunburst 2PEN056 10.00 NET Ea.1.0 Nordic Purple 2PEN058 10.00 NET Ea.1.0 Champagne 2PEN073 10.00 NET Ea.1.0 Spray Green 2PEN701 10.00 NET Ea.1.0 Sagebrush Yellow 2PEN710 10.00 NET Ea.1.0 Lake Blue 2PEN7 10.00 NET Ea.1.0 Mandarin Orange 2PEN720 10.00 NET Ea.1.0 Patriot Red 2PEN722 10.00 NET Ea.1.0 Light Putty 2PEN723 10.00 NET Ea.1.0 Burgundy 2PEN736 10.00 NET Ea.1.0 Cardinal Red 2PEN767 10.00 NET Ea.1.0 Marine Blue 2PEN806 10.00 NET Ea.1.0 Hunter Green 2PEN8 10.00 NET Ea.1.0 Regal Blue 2PEN822 10.00 NET Ea.1.0 Slate Blue 2PEN826 10.00 NET Ea.1.0 January 2PEN848 10.00 NET Ea.1.0 Jet Black 2PEN949 10.00 NET Ea.1.0 Turquoise Teal 2PEN952 10.00 NET Ea.1.0 1.0 oz. Paint Bottles Paint Bottles ship from East Hanover, NJ. Both ship in approximately 10 business days. Store recapped bottles in a cool, dark area for optimal performance. A minimum order of two (2) bottles of the same color is required. Prices shown are as NET PRICE. Tawny Tan 2BCB0 10.00 NET Ea.1.0 Gray Ash 2BCB021 10.00 NET Ea.1.0 Gray 2BCB028 10.00 NET Ea.1.0 Reflex Blue 2BCB052 10.00 NET Ea.1.0 Canvas 2BCB054 10.00 NET Ea.1.0 Shamrock 2BCB055 10.00 NET Ea.1.0 Sunburst 2BCB056 10.00 NET Ea.1.0 Nordic Purple 2BCB058 10.00 NET Ea.1.0 Champagne 2BCB073 10.00 NET Ea.1.0 Spray Green 2BCB701 10.00 NET Ea.1.0 Sagebrush Yellow 2BCB710 10.00 NET Ea.1.0 Lake Blue 2BCB7 10.00 NET Ea.1.0 Mandarin Orange 2BCB720 10.00 NET Ea.1.0 Patriot Red 2BCB722 10.00 NET Ea.1.0 Light Putty 2BCB723 10.00 NET Ea.1.0 Burgundy 2BCB736 10.00 NET Ea.1.0 Cardinal Red 2BCB767 10.00 NET Ea.1.0 Marine Blue 2BCB806 10.00 NET Ea.1.0 Hunter Green 2BCB8 10.00 NET Ea.1.0 Regal Blue 2BCB822 10.00 NET Ea.1.0 Slate Blue 2BCB826 10.00 NET Ea.1.0 January 2BCB848 10.00 NET Ea.1.0 Jet Black 2BCB949 10.00 NET Ea.1.0 Turquoise Teal 2BCB952 10.00 NET Ea.1.0 Paint Pens - 0.33 oz. Paint Bottles - 1 oz. For CUSTOM COLOR Touch Up Paint, contact a Penco representative. 36 Penco Products Inc.

Accessories - Slope Tops & Slope Hoods Individual Slope Top Kits and Individual Unit Slope Tops are NOT for use on Invincible II, All-Welded, Angle Iron, Stadium or Patriot lockers. Individual Slope Top Kit Individual Unit Slope Tops Slope Top Kits, Individual To Convert Flat Tops to Indiv. Slope Tops Designed to convert flat top lockers into slope top lockers in groups of 3-wide. Kit contains 3 tops, 3 backs, 4 ends. 24 Ga. 4 60230H 57.65 Kit 7.0 LPP 5 60232H 64.25 Kit 8.0 LPP 6 60234H 73.30 Kit 9.0 LPP 5 60238H 79.00 Kit 9.0 LPP 6 60240H 88.20 Kit 11.0 LPP 6 60244H 98.95 Kit 14.0 LPP Individual Unit Slope Tops (24 Ga.) For non-stock lockers. An individual slope top for use with non-stock lockers. PRICES ARE FOR USE ONLY WHEN ORDERING WITH LOCKERS. Price includes cost of top, plus higher side(s) & back. For 2-tier lockers, Penco will supply top with holes for ceiling coat hook attachment. Add 10% to 2 wide and 20% to 1 wide locker configurations. 9 60332C 9.95 Ea. 1.0 LPP 9 60334C 10.90 Ea. 2.0 LPP 9 60336C 13.40 Ea. 2.0 LPP 60338C 10.90 Ea. 2.0 LPP 60340C 11.05 Ea. 2.0 LPP 60342C 13.45 Ea. 3.0 LPP 21 60344C 16.30 Ea. 3.0 LPP 24 60370C.95 Ea. 4.0 LPP 603450C 13.25 Ea. 2.0 LPP 60346C 13.40 Ea. 3.0 LPP 60348C 14.10 Ea. 3.0 LPP 21 60350C 16.40 Ea. 4.0 LPP 24 60371C 19.00 Ea. 4.0 LPP 60380C 16.20 Ea. 4.0 LPP 603510C 16.30 Ea. 4.0 LPP 60352C 16.45 Ea. 4.0 LPP 21 60354C 20.45 Ea. 5.0 LPP 24 60356C 23.50 Ea. 5.0 LPP 24 60381C 20.70 Ea. 5.0 LPP 24 60364C 24.85 Ea. 5.0 LPP 24 21 60366C 29.75 Ea. 6.0 LPP 24 24 60368C 34. Ea. 7.0 LPP Continuous Slope Hoods Ga, Available in 72" length only Converts flat top lockers into slope top. Actual length is 72-3/16". Can be cut in field. Ga. Includes 1 hood and 2 supports. 72 5 66144H 108.20 Ea. 17.2 LPP 72 6 66147H 3.50 Ea. 20.2 LPP 72 7 660H 136.75 Ea. 23.2 LPP 72 21 8 663H 7.50 Ea. 26.2 LPP 72 24 9 666H 170.95 Ea. 29.2 LPP 16 Ga, Available in 72" length only Converts flat top lockers into slope top. Actual length is 72-3/16". Can be cut in field. 6 Ga. Includes 1 hood and 2 supports. 72 5 66145H 4.25 Ea. 21.2 LPP 72 6 66148H 143.45 Ea. 25.2 LPP 72 7 661H 160.55 Ea. 28.7 LPP 72 21 8 664H 4.00 Ea. 32.6 LPP 72 24 9 667H 201.00 Ea. 36.2 LPP Universal Hood Support, Extra 2 Supports are included with each 6' hood. Ships flat; packaged with hardware. Bend at right angle on job site for locker depth stamped on support for ", ", ", 21" & 24" deep lockers. Galvanized finish. Note that as of mid-2014, two supports are included in the price of each standard depth hood. 4-24 5-9 66070 7.75 Ea. 0.6 LPP Splice for Hood Use between hoods and between hoods and slope top corner fillers. 66168C 17.30 Ea. 0.5 LPP 66169C.35 Ea. 1.0 LPP 66170C 20.05 Ea. 1.3 LPP 21 66171C 21.40 Ea. 1.5 LPP 24 66172C 24.25 Ea. 1.7 LPP Penco Products Inc. 37

Accessories - Slope Hoods (continued), Hip Fillers, Bases Slope End for Hood Order one for each LH & RH extreme end as required. LH 5 668H.20 Ea. 1.0 LPP RH 5 669H.20 Ea. 1.0 LPP LH 6 66160H 13.45 Ea. 1.5 LPP RH 6 66161H 13.45 Ea. 1.5 LPP LH 7 66162H 14.20 Ea. 2.0 LPP RH 7 66163H 14.20 Ea. 2.0 LPP LH 21 8 66164H.35 Ea. 2.5 LPP RH 21 8 66165H.35 Ea. 2.5 LPP LH 24 9 66166H 16.40 Ea. 3.2 LPP RH 24 9 66167H 16.40 Ea. 3.2 LPP Hip Filler - Outside Corner For use with Slope Hoods ONLY. Requires a hood splice on each side. 6HDX201C 119.45 Ea. 3.5 LPP 6HDX202C 3.80 Ea. 5.4 LPP 6HDX203C 8.00 Ea. 7.2 LPP 21 21 6HDX204C 137.80 Ea. 9.2 LPP 24 24 6HDX205C 147.85 Ea..2 LPP Hip Filler - End of Row For use with Slope Hoods ONLY. Requires 1 hood splice. LH 6HDX274C 0.90 Ea. 3.5 LPP RH 6HDX275C 0.90 Ea. 3.5 LPP LH 6HDX276C 5.20 Ea. 5.4 LPP RH 6HDX277C 5.20 Ea. 5.4 LPP LH 6HDX278C 9.40 Ea. 7.2 LPP RH 6HDX279C 9.40 Ea. 7.2 LPP 21 21 LH 6HDX280C 139.30 Ea. 9.2 LPP 21 21 RH 6HDX281C 139.30 Ea. 9.2 LPP 24 24 LH 6HDX282C 149.35 Ea..2 LPP 24 24 RH 6HDX283C 149.35 Ea..2 LPP Ga, 72" length only. For Lockers 1" from wall. Use only when lockers need to be 1 inch away from wall. Includes 1 piece of hood and 2 hood supports. Do NOT use with STANDARD size Slope Ends, Slope Top Corner Fillers, Hip Fillers or Finished End Panels. See special Splices, Ends & Supports for these hoods below. 72 13 5-1/3 6HDX330H 5.45 Ea..0 LPP 72 16 6-1/3 6HDX4H 141.40 Ea. 21.0 LPP 72 19 7-1/3 6HDX471H 160.90 Ea. 24.0 LPP Splice for Hoods with 1" extra depth at wall. Use between Hoods 13,16 or 19" deep or between Hoods and CUS- TOM Slope Top Corner Fillers. 13 6HDX484C 29.00 Ea. 0.9 LPP 16 6HDX7C 30.85 Ea. 1.2 LPP 19 6HDX473C 33.65 Ea. 1.4 LPP Slope End for Hoods with 1" extra depth at wall. Order one for each LH & RH extreme end as required for lockers 1" from wall. LH 13 5-1/3 6HDX642H.85 Ea. 1.3 LPP RH 13 5-1/3 6HDX643H.85 Ea. 1.3 LPP LH 16 6-1/3 6HDX5H 13.90 Ea. 1.8 LPP RH 16 6-1/3 6HDX6H 13.90 Ea. 1.8 LPP LH 19 7-1/3 6HDX694H 14.85 Ea. 2.9 LPP RH 19 7-1/3 6HDX695H 14.85 Ea. 2.9 LPP Extra Supports for Hood with 1" extra depth at wall. NOTE: 2 Hood Supports are included in the price of each piece of Hood. Use only to support 13"d (5-1/3"h), 16"d (6-1/3"h) or 19" deep (7-1/3"h) hoods. 5-1/3 6HDX480C.55 Ea. 0.3 LPP 6-1/3 6HDX481C 13.40 Ea. 0.6 LPP 7-1/3 6HDX474C 14.65 Ea. 0.9 LPP Bottom Bearing Angles Use 1 per Frame (16 Ga.) Supports locker bottom from front to back when locker overhangs base more than 1". 6098C 2.50 Ea. 0.3 LPP 6098C 3.40 Ea. 0.4 LPP 6098C 4.25 Ea. 0.5 LPP 21 609821C 5.95 Ea. 0.6 LPP 24 609824C 6.95 Ea. 0.7 LPP Front Bases (NOT for Welded Lockers) Gauge. Locker bases cannot be used at rear, however, filler 66117C can be drilled and used as a rear base. 9 6 60216C 10.20 Ea. 1.0 LPP 6 60217C 10.30 Ea. 1.0 LPP 6 602C 11.10 Ea. 2.0 LPP 6 60219C.55 Ea. 2.0 LPP 24 6 60220C 14.05 Ea. 3.0 LPP End Bases Single Row (NOT for Welded Lockers) 6 60204C.35 Ea. 1.0 LPP 6 60205C.40 Ea. 2.0 LPP 6 60206C 17. Ea. 2.0 LPP 21 6 60207C 17.35 Ea. 2.0 LPP 24 6 60208C.70 Ea. 3.0 LPP FRONT BASE (snaps in) END BASE (slips over legs during locker assembly) Hip Fillers for Slope Hood There are two types of Hip Ends: "outside Corner" and " End of Row" (which come in left and right hand ends). The "Outside Corner" Hip End attaches to slope hoods on both the right and left sides using hood splices. The left and right "End of Row" Hip Ends attach to slope hoods on only one side. Right hand Hip Ends end locker runs on the right; left hand Hip Ends end locker runs on the left. Hip Ends are attached through locker tops by drilling pilot holes and attaching with screws or by using self-tapping screws in two places ( minimum). 38 Penco Products Inc.

Zee Base, 4" High Front Zee Base (14 Ga.) NOT FOR ALL-WELDED, ANGLE IRON, STADIUM OR PATRIOT LOCKERS A continuous 4" high steel base used with lockers with NO legs. Must be cut to length in field. See also #60092C - Rear Leg for use with 4" Zee base. 72 4 66700H 54.10 Ea. 11.0 LPP Splice/End Base, Single Row For 4" High Zee Base (Use at ends of rows & where 6' sections adjoin). 4 66701H 25.85 Ea. 1.6 LPP 4 66702H 27.20 Ea. 1.9 LPP 4 66703H 29.10 Ea. 2.2 LPP 21 4 66704H 34. Ea. 2.5 LPP 24 4 66705H 35.40 Ea. 2.8 LPP Splice/End Base, for back-to-back lockers 24 4 66706H 48.70 Ea. 2.6 LPP 30 4 66707H 53.10 Ea. 3.1 LPP 36 4 66708H 56.40 Ea. 3.7 LPP Zee Inside Corner Splice 4 66709H 16.45 Ea. 0.9 LPP Rear Leg, Use With 4" Zee 13 60092C 3.40 Ea. 0.5 LPP Zee Base, 6" High Front Zee Base (14 Ga.) NOT FOR ALL-WELDED, ANGLE IRON, STADIUM OR PATRIOT LOCKERS A continuous 6" high steel base used with lockers with NO legs. Must be cut to length in field. For REAR 6" legs, see # 60091C below. 72 6 66710H 79.00 Ea. 14.2 LPP Splice/End Base, Single Row For 6" High Zee Base (Use at ends of rows & where 6' sections adjoin). 6 66711H 40.50 Ea. 2.1 LPP 6 667H 42.65 Ea. 2.3 LPP 6 66713H 44.90 Ea. 2.5 LPP 21 6 66714H 51.20 Ea. 2.8 LPP 24 6 667H 53.30 Ea. 3.6 LPP Splice/End Base, for back-to-back lockers 24 6 66716H 74.70 Ea. 3.6 LPP 30 6 66717H 81.10 Ea. 4.4 LPP 36 6 667H 85.40 Ea. 5.3 LPP Zee Inside Corner Splice 6 66719H 29.95 Ea. 0.7 LPP Standard 6" Rear Leg Actual Ht.= ". Also used with standard lockers with 6" Legs. 6 60091C 7. Ea. 0.7 LPP SPLICE/END BASE ANCHOR TO FLOOR AT 24" O. C. Accessories - Zee Base, Fillers 72" CONTINUOUS ZEE BASE Fillers, Standard Vertical Angles For wider fillers, use two angle fillers and 2 slip joints. 5 36-1/2 66190C 17.30 Ea. 3.9 LPP 5 48-1/2 66191C 20.50 Ea. 5.1 LPP 5 60 661C 23.95 Ea. 4.0 LPP 5 66 6622C 26.50 Ea. 4.5 LPP 5 72 661C 28.90 Ea. 5.0 LPP 9 36-1/2 66192C 29.10 Ea. 6.2 LPP 9 48-1/2 66193C 34.25 Ea. 8.3 LPP 9 60 66114C 39.50 Ea. 7.0 LPP 9 66 664C 45.00 Ea. 7.5 LPP 9 72 66117C 49.10 Ea. 8.0 LPP 9 78 667C 52. Ea. 9.0 LPP 36-1/2 66194C 34.00 Ea. 7.9 LPP 48-1/2 66195C 40. Ea. 10.6 LPP 60 66113C 46.00 Ea. 9.0 LPP 66 6621C 46.75 Ea. 9.5 LPP 72 661141C 50.95 Ea. 10.0 LPP 78 66116C 53.35 Ea. 11.0 LPP 90 661173C 61.85 Ea. 13.5 LPP Wall Angles (Slip Joint) 36-1/2 66200C 20.35 Ea. 1.7 LPP 48-1/2 66201C 23.75 Ea. 2.3 LPP 60 661C 27.70 Ea. 3.5 LPP 66 660C 31.30 Ea. 3.8 LPP 72 66119C 34. Ea. 4.2 LPP 78 661C 43.90 Ea. 4.6 LPP 90 66C 64.10 Ea. 5.0 LPP Flat Top Fillers - Overlaps standard tops 661321C.35 Ea. 2.0 LPP 661322C 20.35 Ea. 3.0 LPP 661323C 23.90 Ea. 4.0 LPP 21 661324C 28.20 Ea. 5.0 LPP 24 661325C 35.40 Ea. 6.0 LPP Slope Top Fillers NOT for use with Slope Hoods. 661371C 19.10 Ea. 2.0 LPP 661372C 21.40 Ea. 3.0 LPP 661373C 24.70 Ea. 4.0 LPP 21 661374C 30.60 Ea. 5.0 LPP 24 661375C 37.80 Ea. 6.0 LPP Flat Top Corner Fillers 66138C.35 Ea. 3.0 LPP 66139C 20.45 Ea. 4.0 LPP 66140C 28.90 Ea. 5.0 LPP 21 21 66141C 37.80 Ea. 6.0 LPP 24 24 66142C 49.25 Ea. 7.0 LPP Slope Top Corner Fillers For use with Individual Slope Tops or Hoods. 66100C 116.30 Ea. 3.0 LPP 66101C 1.50 Ea. 4.0 LPP 66102C 1.90 Ea. 6.0 LPP 21 21 66103C 9.05 Ea. 9.0 LPP 24 24 66104C 3.55 Ea. 11.0 LPP Closure Strip Used for closing gaps between lockers and wall at top and side of locker. 3 72 66111H 24.25 Ea. 2.4 LPP 6 72 6611 30.05 Ea. 4.6 LPP Inside Corner Filler (Z) 60 66360 33.95 Ea. 3.5 LPP 66 66366 37.80 Ea. 3.8 LPP 72 66372 40.80 Ea. 4.2 LPP 78 66378 44.45 Ea. 4.5 LPP Penco Products Inc. 39

Accessories - Fillers (continued), Recess Trim Fillers for Welded Lockers w/4" Base The following items are intended for welded lockers with 4" high integral bases ONLY. Vertical Angles (for Welded w/base) 5 64 6613C 26.40 Ea. 4.3 LPP 5 76 6614C 30.55 Ea. 5.4 LPP 9 64 66C 44.30 Ea. 7.3 LPP 9 76 6616C 51.05 Ea. 8.4 LPP 64 6617C 47.65 Ea. 9.3 LPP 76 66C 51.35 Ea. 10.4 LPP Wall Angles (for Welded w/base) 64 6611C 29.90 Ea. 3.7 LPP 76 6612C 40.70 Ea. 4.4 LPP Heavy Gauge Custom Fillers VERTICAL OR FLAT TOP FILLERS Side Trim; For Use w/top & Bottom Trim - LH 3 66 60477C 41.65 Ea. 5.3 LPP 3 78 60479C 44.90 Ea. 6.3 LPP 3 90 60481C 51.20 Ea. 7.3 LPP Side Trim; For Use w/top & Bottom Trim - RH 3 66 60478C 41.65 Ea. 4.8 LPP 3 78 60480C 44.90 Ea. 5.6 LPP 3 90 60482C 51.20 Ea. 6.5 LPP Recess Trim Recess Trim - 3" Recess trim bridges the gap between lockers and wall and/or soffits when the lockers are recessed into a wall. Front View of Locker with Recessed Trim Side Trim L.H. Splice Top Trim Side Trim R.H. Vertical fillers up to " wide(16 GA) Price Weight/lbs $24.90 /Sq Ft 3 Lbs/Sq. Ft. For Top fillers or Facia panels, please submit a dimensioned detail sketch with the order. Recess Trim Side Trim, Left Hand (NO Legs) 3 63 60465C 33.55 Ea. 5.0 LPP 3 75 60469C 36.60 Ea. 6.0 LPP 3 87 60473C 42.65 Ea. 7.0 LPP Side Trim, Right Hand (NO Legs) 3 63 60466C 33.55 Ea. 5.0 LPP 3 75 60470C 36.60 Ea. 6.0 LPP 3 87 60474C 42.65 Ea. 7.0 LPP Side Trim; Use w/top Trim & 6" LEGS - LH 3 69 60467C 43.40 Ea. 5.6 LPP 3 81 60471C 46.50 Ea. 6.6 LPP 3 93 60475C 52.90 Ea. 7.6 LPP Side Trim; Use w/top Trim & 6" LEGS - RH 3 69 60468C 43.40 Ea. 5.6 LPP 3 81 60472C 46.50 Ea. 6.6 LPP 3 93 60476C 52.90 Ea. 7.6 LPP Top Trim Includes Clips & Screws 74 3 60456H 35.70 Ea. 5.0 LPP Splice 2 3 66105C 6.35 Ea. 0.1 LPP Corner Splice for Outside Corner 2 2 3 66108C 16.45 Ea. 0.3 LPP Corner Splice for Inside Corner 2 2 3 66040C 21.40 Ea. 0.3 LPP Top Trim End Cap Assembly 3 66001C 21.35 Ea. 0.2 LPP Bottom Trim 74 3 60458C 36.35 Ea. 5.0 LPP A. Vanguard w/optional full louvers B. Vanguard w/optional recessed handle C. Fire extinguisher / waste bin door D. Vanguard w/optional visual perforations E. Invincible II Lockers must be anchored to base (base and wood to be completed by General Contractor) Example of Side View of Base and Anchor 3/4" Max. Side View of Top Recessed Trim 3" Recessed Trim 1" Top of Locker Frame Locker Door 3/8" Soffit Trim Clip Wood used to anchor lockers Concrete Base 4-1/8" Soffit to be constructed by general contractor. Face of soffit must be flush with face of locker. There should be 1" between top of locker and bottom of soffit. The recessed trim extends 3/8" from face of soffit. Top View of a Recessed Locker Gouping Recessed Opening = Length of Locker Group (w/growth) + 3" Wall Doors Locker Frame Top View of 3" Vertical Trim R.H. Vertical Trim Width between Locker and Wall can vary between 3/4" to 2" 3/8" Offset from Wall 40 Penco Products Inc.

Accessories - Extra Locker Shelves / 16 Ga. Shelves, etc. Extra Locker Shelves (24 Ga.) Note: KD lockers, Vanguard, Guardian - 60 and 72 high locker divisions already have punching at different locations. When ordering an extra shelf that requires a location other than what is already punched, drilling and attachment of the shelf may have to be completed on site by the installer. If custom punching is needed, the order will need to be detailed. For punching sides ADD $25.00 for each custom shelf location to the price of the shelf. Only for use on lockers with 24 gauge bodies. 7-1/2 P 60390C 8.60 Ea. 1.0 LPP 7-1/2 P 60392C 8.80 Ea. 1.0 LPP 9 P 60394C 8.35 Ea. 1.0 LPP 9 P 60396C 8.80 Ea. 1.0 LPP 9 P 60398C 9.30 Ea. 1.0 LPP P 60400C 9.50 Ea. 1.0 LPP P 60402C 9.85 Ea. 2.0 LPP P 60404C 10.90 Ea. 2.0 LPP 21 P 604041C 11.05 Ea. 2.0 LPP 24 P 60430C.40 Ea. 2.0 LPP P 604050C 11.60 Ea. 2.0 LPP P 60406C 11.90 Ea. 2.0 LPP P 60408C.55 Ea. 2.0 LPP 21 P 60410C 13.40 Ea. 2.0 LPP 24 P 6041C 14.20 Ea. 3.0 LPP P 604111C.30 Ea. 2.0 LPP P 604110C 13.25 Ea. 2.3 LPP P 604C 14.20 Ea. 3.0 LPP 21 P 60414C.35 Ea. 3.0 LPP 24 P 60416C 16.45 Ea. 3.0 LPP 24 P 604241C 16.10 Ea. 2.8 LPP 24 P 60424C 17.30 Ea. 3.0 LPP 24 21 P 60426C.60 Ea. 4.0 LPP 24 24 P 60428C 20.45 Ea. 4.0 LPP Extra Locker Shelves (16 Ga.) Note: KD lockers, Invincible II - 60 and 72 high locker divisions already have punching at different locations. When ordering an extra shelf that requires a location other than what is already punched, drilling and attachment of the shelf may have to be completed on site by the installer. If custom punching is needed, the order will need to be detailed. For punching sides ADD $25.00 for each custom shelf location to the price of the shelf. 16 gauge shelves are for Invincible II and All-Welded lockers. NOT intended for use on Patriot, Angle Iron, Rapid Response Duffel or Stadium lockers. 9 P 605400C 13.80 Ea. 2.5 LPP 9 P 605414C.05 Ea. 3.1 LPP 9 P 605428C 16.40 Ea. 3.5 LPP P 605401C.55 Ea. 3.2 LPP P 6054C 16.25 Ea. 3.8 LPP P 605429C.60 Ea. 4.5 LPP 21 P 605443C 19.55 Ea. 5.7 LPP 24 P 605457C 21.40 Ea. 5.9 LPP P 605402C.30 Ea. 3.9 LPP P 605416C 19.60 Ea. 4.6 LPP P 605430C 20.90 Ea. 5.5 LPP 21 P 605444C 23. Ea. 6.3 LPP 24 P 605458C 25.85 Ea. 7.2 LPP P 605403C 21.20 Ea. 4.6 LPP P 605417C 22.45 Ea. 5.4 LPP P 605431C 23.80 Ea. 6.4 LPP 21 P 605445C 24.95 Ea. 7.4 LPP 24 P 605459C 28.40 Ea. 8.5 LPP 24 P 605419C 48.45 Ea. 7.1 LPP 24 P 605433C 51.65 Ea. 8.4 LPP 24 21 P 605447C 59.90 Ea. 9.7 LPP 24 24 P 605461C 67.25 Ea. 11.0 LPP Extra Cost To CHANGE Locker SHELF From 24 Ga. to 16 Ga Description To upgrade locker shelves from 24 ga. to 16 ga. show the additional charge and weight at right as a separate line item on the estimate/purchase order. Size W x D Price Extra Wt. 9 x 5.45 1.2 9 x 6.25 1.5 9 x 7.10 1.8 x 6.05 1.5 x 6.40 1.9 x 7.70 2.3 x 21 8.50 2.7 x 24 9.00 3.2 x 6.70 1.9 x 7.70 2.4 x 8.35 2.8 x 21 9.75 3.2 x 24 11.65 4.0 x 8.90 2.4 x 9.20 2.7 x 9.60 3.0 x 21 10.20 3.4 x 24 11.95 4.5 24 x 32.35 3.9 24 x 34.35 4.5 24 x 21 41.30 5.3 24 x 24 46.80 6.0 Extra Cost To CHANGE Locker TOP, BOTTOM or INTERMEDIATE BOTTOM From 24 Ga. to 16 Ga. To upgrade the top or bottom from 24 ga. to 16 ga. show the additional charge and weight for each top or bottom at right as a separate line item on the estimate/purchase order. 9 x 5.45 1.2 9 x 6.25 1.5 9 x 7.10 1.8 x 6.05 1.5 x 6.40 1.9 x 7.70 2.3 x 21 8.50 2.7 x 24 9.00 3.2 x 6.70 1.9 x 7.70 2.4 x 8.35 2.8 x 21 9.75 3.2 x 24 11.65 4.0 x 8.90 2.4 x 9.20 2.7 x 9.60 3.0 x 21 10.20 3.4 x 24 11.95 4.5 24 x 32.35 3.9 24 x 34.35 4.5 24 x 21 41.30 5.3 24 x 24 46.80 6.0 Penco Products Inc. 41

Accessories - Electrogalvanizing / Custom Ends / 16 Ga. Ends To ADD Galvanneal to Standard 24 Ga. & 16 Ga. Shelves & Intermediate Shelves Show the additional charge below as a separate line item on the estimate/purchase order. 24 Ga. SHELF 16 Ga. SHELF Width Price Ea. Width Price Ea. 9" $1.40 9" $2.45 " $1.90 " $3.20 " $2.45 " $3.90 " $2.50 " $4.30 24" $3.10 24" $5.30 24 Ga TOP, BOTTOM or INTERMEDIATE BOTTOM 16 Ga TOP, BOTTOM or INTERMEDIATE BOTTOM Width Price Ea. Width Price Ea. 9" $2.40 9" $2.60 " $3.20 " $3.55 " $3.95 " $3.85 " $4.10 " $4.35 24" $4.75 24" $5.00 CUSTOM 16 GAUGE LOCKER ENDS To substitute 16 Gauge Locker Ends for 24 Gauge Ends. Use for row ends only - (specify LH or RH when using slope tops). Prices are for ordering at the same time as lockers. Custom Ends have perimeter, shelf and coat hook holes for each specific locker type. Add: $4.62/Sq. Ft. 1.5 Lbs/Sq. Ft. NOTE: If custom heavy gauge ends are ordered to replace existing ends, add the above prices to the appropriate price of the 24 gauge division priced later in this book. For FINISHED END PANELS, see pages 43-47. 16 Ga. Exposed Locker Ends Punched with perimeter holes only. NOT a Finished End Panel. FIELD-DRILLING FOR SHELVES AND COAT HOOKS IS REQUIRED. Advantage over CUSTOM 16 Gauge Locker Ends is faster shipment and no set up charge. Field installed only. For Flat Top For Use as Row Ends May be installed in place of 24 Ga. end (field drill for hooks/shelves), or by placing it OVER the 24 Ga. end bolted to the shelves & hooks. Attach 16 Ga. end to frame, back, top & bottom only with the same bolts used for the 24 Ga. side beneath. 36-1/2 6060C 37.90 Ea. 7.0 LPP 36-1/2 6070C 48.20 Ea. 8.9 LPP 36-1/2 6080C 56.60 Ea. 10.8 LPP 48-1/2 601360C 43.20 Ea. 10.0 LPP 48-1/2 601370C 54.70 Ea. 11.8 LPP 48-1/2 601380C 65.80 Ea. 14.3 LPP 60 601660C 51.20 Ea. 11.0 LPP 60 601670C 64.10 Ea. 14.0 LPP 60 601680C 76.85 Ea. 17.0 LPP 21 60 601690C 89.35 Ea. 20.0 LPP 24 60 601700C 102.70 Ea. 23.0 LPP 72 601780C 61.85 Ea. 13.0 LPP 72 601790C 74.70 Ea. 16.8 LPP 72 6000C 87.40 Ea. 20.5 LPP 21 72 6009C 102.30 Ea. 24.0 LPP 24 72 6010C 117.20 Ea. 28.3 LPP For Slope Top (Individual) NOTE: For lockers with Hoods, use Flat Top Ends. RH 64 6020C 53.30 Ea..5 LPP LH 64 6021C 53.30 Ea..5 LPP RH 65 6030C 66.20 Ea..0 LPP LH 65 6031C 66.20 Ea..0 LPP RH 66 6040C 79.00 Ea..8 LPP LH 66 6041C 79.00 Ea..8 LPP RH 76 601960C 64.10 Ea. 14.0 LPP LH 76 601961C 64.10 Ea. 14.0 LPP RH 77 601970C 76.85 Ea..3 LPP LH 77 601971C 76.85 Ea..3 LPP RH 78 601980C 89.60 Ea. 20.8 LPP LH 78 601981C 89.60 Ea. 20.8 LPP RH 21 67 6060C 92.10 Ea. 21.1 LPP LH 21 67 6061C 92.10 Ea. 21.1 LPP RH 24 68 6070C 106.10 Ea. 24.2 LPP LH 24 68 6071C 106.10 Ea. 24.2 LPP RH 21 79 6080C 105.95 Ea. 23.5 LPP LH 21 79 6081C 105.95 Ea. 23.5 LPP RH 24 80 601990C 0.95 Ea. 27.0 LPP LH 24 80 601991C 0.95 Ea. 27.0 LPP 42 Penco Products Inc.

Finished End Panels - General Information Finished End Panels (FEP for short) are designed to be fastened to row ends of lockers without any exposed fasteners. Each panel is made in a box formation that adds 1" to the length of the row. Panels are fastened from the inside of the lockers with screws (furnished). There are different types of FEP's, depending on the locker type used. It is imperative to choose the correct FEP for the application. Although all panel types look similar, there is only one correct type for the application! The following pages contain catalog numbers and prices of FEP's for the most popular locker sizes. For sizes not shown with a catalog number, calculate the price as follows: Multiply the depth x height (include 6" legs or channel base height, and for lockers with slope tops, use the height to the peak of the FEP - see the table below for that dimension), divide the answer (sq. inches) by 144 to obtain square feet, and multiply by $.90 to obtain the list price. Allow 3.2 lbs. per Sq. Ft. It is REQUIRED to specify the following: Flat or Slope top, (if slope, whether continuous hoods or unit slope tops) Left or Right Hand (except for back-to-back/double row configurations), Legs or No Legs, and if legs (or channel base on a welded locker), advise if the panel goes all the way to the floor. SEE THE ILLUSTRATIONS OF MOST TYPES OF FINISHED END PANEL APPLICATIONS ON SUBSEQUENT PAGES. They are keyed with a letter code (A through R) that corresponds to a section with catalog numbers. Please contact a Penco representative with any questions. Finished End Panels ordered in error cannot be returned for credit. Slope Top Finished End Panel (FEP) Heights for Lockers with Unit Slope Tops & Continuous Slope Hoods All dimensions shown are in Inches Basic Locker Size Depth (In.) Finished End Panels - Introduction Height (In.) Lockers with NO Legs and Lockers with Zee Base (see diagram below) UNIT Slope Top FEP Height Continuous Slope HOOD FEP Height Lockers WITH 6" Legs UNIT Slope Top FEP Height Continuous Slope HOOD FEP Height Welded Lockers WITH 4" High Channel Base * Continuous Slope HOOD FEP Height Single Row FEP on All-Welded locker with Channel Base and Continuous Slope Hood. 60 64 65 70 71 69 60 65 66 71 72 70 60 66 67 72 73 71 21 60 67 68 73 74 72 24 60 68 69 74 75 73 72 76 77 82 83 81 72 77 78 83 84 82 72 78 79 84 85 83 21 72 79 80 85 86 84 24 72 80 81 86 87 85 * Calculate the price for the sizes in the shaded area - the catalog numbers are NOT in this price book. 24" deep back-to-back fullylouvered all-welded lockers on tile base with Continuous Slope Hood, each row with single row 24" deep FEP. With Zee Base, the Finished End Panel extends to the bottom of the locker, NOT to the floor. Single Row FEP on Guardian Defiant II locker with Zee Base and Continuous Slope Hood. Double Row FEP on Vanguard lockers with Continuous Slope Hood on concrete base. Penco Products Inc. 43

Finished End Panels - For FLAT TOP Lockers For FLAT TOP Lockers Single Row (SR). Take care to order for Left OR Right Hand, and With OR Without 6" legs. Verify with the illustrations below before ordering! Finished End Panels ordered in error cannot be returned for credit. Finished End Panels - FLAT TOP Lockers (SR) A. LEFT Hand, NO Legs Single Row 1 60 66429H 94.50 Ea. 16.0 LPP 1 60 66431H 1.13 Ea. 20.0 LPP 1 60 66433H 141.75 Ea. 24.0 LPP 1 21 60 66439H 165.38 Ea. 28.0 LPP 1 24 60 66441H 9.00 Ea. 32.0 LPP 1 72 66443H 113.40 Ea. 19.2 LPP 1 72 66445H 141.75 Ea. 24.0 LPP 1 72 66447H 170.10 Ea. 28.8 LPP 1 21 72 66453H 198.45 Ea. 33.6 LPP 1 24 72 66455H 226.80 Ea. 38.4 LPP B. RIGHT Hand, NO Legs 1 60 66430H 94.50 Ea. 16.0 LPP 1 60 66432H 1.13 Ea. 20.0 LPP 1 60 66434H 141.75 Ea. 24.0 LPP 1 21 60 66440H 165.38 Ea. 28.0 LPP 1 24 60 66442H 9.00 Ea. 32.0 LPP 1 72 66444H 113.40 Ea. 19.2 LPP 1 72 66446H 141.75 Ea. 24.0 LPP 1 72 66448H 170.10 Ea. 28.8 LPP 1 21 72 66454H 198.45 Ea. 33.6 LPP 1 24 72 66456H 226.80 Ea. 38.4 LPP C. LEFT Hand, WITH Legs 1 66 66401H 103.95 Ea. 17.6 LPP 1 66 66403H 9.94 Ea. 22.0 LPP 1 66 66405H 5.93 Ea. 26.4 LPP 1 21 66 66411H 1.91 Ea. 30.8 LPP 1 24 66 66413H 207.90 Ea. 35.2 LPP 1 78 664H 2.85 Ea. 20.8 LPP 1 78 66417H 3.56 Ea. 26.0 LPP 1 78 66419H 4.28 Ea. 31.2 LPP 1 21 78 66425H 214.99 Ea. 36.4 LPP 1 24 78 66427H 245.70 Ea. 41.6 LPP D. RIGHT Hand, WITH Legs 1 66 66402H 103.95 Ea. 17.6 LPP 1 66 66404H 9.94 Ea. 22.0 LPP 1 66 66406H 5.93 Ea. 26.4 LPP 1 21 66 664H 1.91 Ea. 30.8 LPP 1 24 66 66414H 207.90 Ea. 35.2 LPP 1 78 66416H 2.85 Ea. 20.8 LPP 1 78 664H 3.56 Ea. 26.0 LPP 1 78 66420H 4.28 Ea. 31.2 LPP 1 21 78 66426H 214.99 Ea. 36.4 LPP 1 24 78 66428H 245.70 Ea. 41.6 LPP No Legs With 6" Legs Be sure to select the correct TYPE of Finished End Panel in the size needed for the lockers. Each of the types shown on this page are different, and are not interchangeable! See the previous page for additional information. Reference the letter codes in the illustrations above to the product listings on the left column. 44 Penco Products Inc.

Finished End Panels - For UNIT SLOPE TOP Lockers For UNIT SLOPE TOP Lockers Single Row (SR). Take care to order for Left OR Right Hand, and With OR Without 6" legs. Finished End Panels ordered in error cannot be returned for credit. Finished End Panels - UNIT SLOPE TOP Lockers (SR) NOT for use with continuous slope hoods. E. LEFT Hand, NO Legs 1 64 66509H 100.80 Ea. 17.1 LPP 1 65 66511H 7.97 Ea. 21.7 LPP 1 66 66513H 5.93 Ea. 26.4 LPP 1 21 67 66519H 4.67 Ea. 31.3 LPP 1 24 68 66521H 214.20 Ea. 36.3 LPP 1 76 66523H 119.70 Ea. 20.3 LPP 1 77 66525H 1.59 Ea. 25.7 LPP 1 78 66527H 4.28 Ea. 31.2 LPP 1 21 79 66533H 217.74 Ea. 36.9 LPP 1 24 80 66535H 252.00 Ea. 42.7 LPP F. RIGHT Hand, NO Legs 1 64 66510H 100.80 Ea. 17.1 LPP 1 65 665H 7.97 Ea. 21.7 LPP 1 66 66514H 5.93 Ea. 26.4 LPP 1 21 67 66520H 4.67 Ea. 31.3 LPP 1 24 68 66522H 214.20 Ea. 36.3 LPP 1 76 66524H 119.70 Ea. 20.3 LPP 1 77 66526H 1.59 Ea. 25.7 LPP 1 78 66528H 4.28 Ea. 31.2 LPP 1 21 79 66534H 217.74 Ea. 36.9 LPP 1 24 80 66536H 252.00 Ea. 42.7 LPP G. LEFT Hand, WITH Legs 1 70 66481H 110.25 Ea..7 LPP 1 71 66483H 139.78 Ea. 23.7 LPP 1 72 66485H 170.10 Ea. 28.8 LPP 1 21 73 66491H 201.21 Ea. 34.1 LPP 1 24 74 66493H 233.10 Ea. 39.5 LPP 1 82 66495H 9. Ea. 21.9 LPP 1 83 66497H 163.41 Ea. 27.7 LPP 1 84 66499H 198.45 Ea. 33.6 LPP 1 21 85 66505H 234.28 Ea. 39.7 LPP 1 24 86 66507H 270.90 Ea. 45.9 LPP H. RIGHT Hand, WITH Legs 1 70 66482H 110.25 Ea..7 LPP 1 71 66484H 139.78 Ea. 23.7 LPP 1 72 66486H 170.10 Ea. 28.8 LPP 1 21 73 66492H 201.21 Ea. 34.1 LPP 1 24 74 66494H 233.10 Ea. 39.5 LPP 1 82 66496H 9. Ea. 21.9 LPP 1 83 66498H 163.41 Ea. 27.7 LPP 1 84 66500H 198.45 Ea. 33.6 LPP 1 21 85 66506H 234.28 Ea. 39.7 LPP 1 24 86 66508H 270.90 Ea. 45.9 LPP No Legs With 6" Legs Be sure to select the correct TYPE of Finished End Panel in the size needed for the lockers. Each of the types shown on this page are different, and are not interchangeable! See the FEP introduction page for additional information. Reference the letter codes in the illustrations above to the product listings in the left column. Penco Products Inc. 45

Finished End Panels - For Continuous SLOPE HOODS For CONTINUOUS SLOPE HOOD Lockers (Single Row - SR) Finished End Panels used with lockers with continuous slope hoods are one inch higher than those designed for unit slope tops because of the 1" vertical rise at the front of the hoods. It is NOT necessary to order Slope Ends for Hoods at the ends of rows that have FEP's. Take care to order for Left OR Right Hand, and With OR Without 6" legs. Finished End Panels ordered in error cannot be returned for credit. Finished End Panels - Continuous SLOPE HOOD Lockers (SR) NOT for use with unit slope tops. I. LEFT Hand, NO Legs 1 65 66611H 102.38 Ea. 17.3 LPP 1 66 66613H 9.94 Ea. 22.0 LPP 1 67 666H 8.29 Ea. 26.8 LPP 1 21 68 66617H 7.43 Ea. 31.7 LPP 1 24 69 66619H 217.35 Ea. 36.8 LPP 1 77 66631H 1.28 Ea. 20.5 LPP 1 78 66633H 3.56 Ea. 26.0 LPP 1 79 66635H 6.64 Ea. 31.6 LPP 1 21 80 66637H 220.50 Ea. 37.3 LPP 1 24 81 66639H 255. Ea. 43.2 LPP J. RIGHT Hand, NO Legs 1 65 666H 102.38 Ea. 17.3 LPP 1 66 66614H 9.94 Ea. 22.0 LPP 1 67 66616H 8.29 Ea. 26.8 LPP 1 21 68 666H 7.43 Ea. 31.7 LPP 1 24 69 66620H 217.35 Ea. 36.8 LPP 1 77 66632H 1.28 Ea. 20.5 LPP 1 78 66634H 3.56 Ea. 26.0 LPP 1 79 66636H 6.64 Ea. 31.6 LPP 1 21 80 66638H 220.50 Ea. 37.3 LPP 1 24 81 66640H 255. Ea. 43.2 LPP K. LEFT Hand, WITH Legs 1 71 66571H 111.83 Ea..9 LPP 1 72 66573H 141.75 Ea. 24.0 LPP 1 73 66575H 172.46 Ea. 29.2 LPP 1 21 74 66577H 203.96 Ea. 34.5 LPP 1 24 75 66579H 236.25 Ea. 40.0 LPP 1 83 66591H 130.73 Ea. 22.1 LPP 1 84 66593H 165.38 Ea. 28.0 LPP 1 85 66595H 200.81 Ea. 34.0 LPP 1 21 86 66597H 237.04 Ea. 40.1 LPP 1 24 87 66599H 274.05 Ea. 46.4 LPP L. RIGHT Hand, WITH Legs 1 71 66572H 111.83 Ea..9 LPP 1 72 66574H 141.75 Ea. 24.0 LPP 1 73 66576H 172.46 Ea. 29.2 LPP 1 21 74 66578H 203.96 Ea. 34.5 LPP 1 24 75 66580H 236.25 Ea. 40.0 LPP 1 83 66592H 130.73 Ea. 22.1 LPP 1 84 66594H 165.38 Ea. 28.0 LPP 1 85 66596H 200.81 Ea. 34.0 LPP 1 21 86 66598H 237.04 Ea. 40.1 LPP 1 24 87 66600H 274.05 Ea. 46.4 LPP No Legs With 6" Legs Be sure to select the correct TYPE of Finished End Panel in the size needed for the lockers. Each of the types shown on this page are different, and are not interchangeable! See the FEP introduction page for additional information. Reference the letter codes in the illustrations above to the product listings in the left column. 46 Penco Products Inc.

Finished End Panels - For Back-to-Back Configuration Back-to-Back Finished / DOUBLE End ROW Panels (DR) for Finished Double End Row Panels Finished End Panels for lockers in a Double Row configuration (fastened back-to-back) can be used on the left or right hand, interchangeably. The maximum depth for a single panel is 36"; for back-to back lockers each greater than " deep we will supply two separate panels. Take care to order select Flat Tops OR Unit Slope Tops OR Continuous Slope Hoods and with OR without 6" legs. Finished End Panels ordered in error cannot be returned for credit. Finished End Panels - FLAT TOP Lockers (DR) M. NO Legs, Double Row 1 24 60 66475H 9.00 Ea. 32.0 LPP 1 24 72 66476H 226.80 Ea. 38.4 LPP 1 30 60 66477H 236.25 Ea. 40.0 LPP 1 30 72 66478H 283.50 Ea. 48.0 LPP 1 36 60 66479H 283.50 Ea. 48.0 LPP 1 36 72 66480H 340.20 Ea. 57.6 LPP N. WITH Legs, Double Row 1 24 66 66469H 207.90 Ea. 35.2 LPP 1 24 78 66470H 245.70 Ea. 41.6 LPP 1 30 66 66471H 259.88 Ea. 44.0 LPP 1 30 78 66472H 307.13 Ea. 52.0 LPP 1 36 66 66473H 311.85 Ea. 52.8 LPP 1 36 78 66474H 368.55 Ea. 62.4 LPP Finished End Panels - UNIT SLOPE TOP Lockers (DR) O. NO Legs, Double Row 1 24 64 66555H 201.60 Ea. 34.1 LPP 1 24 76 66556H 239.40 Ea. 40.5 LPP 1 30 65 66557H 255.94 Ea. 43.3 LPP 1 30 77 66558H 303.19 Ea. 51.3 LPP 1 36 66 66559H 311.85 Ea. 52.8 LPP 1 36 78 66560H 368.55 Ea. 62.4 LPP P. WITH Legs, Double Row 1 24 70 66549H 220.50 Ea. 37.3 LPP 1 24 82 66550H 258.30 Ea. 43.7 LPP 1 30 71 66551H 279.56 Ea. 47.3 LPP 1 30 83 66552H 326.81 Ea. 55.3 LPP 1 36 72 66553H 340.20 Ea. 57.6 LPP 1 36 84 66554H 396.90 Ea. 67.2 LPP Finished End Panels - Continuous SLOPE HOOD Lockers (DR) Q. NO Legs, Double Row 1 24 65 66659H 204.75 Ea. 34.7 LPP 1 30 66 66660H 259.88 Ea. 44.0 LPP 1 36 67 66661H 316.58 Ea. 53.6 LPP 1 24 77 66662H 242.55 Ea. 41.1 LPP 1 30 78 66663H 307.13 Ea. 52.0 LPP 1 36 79 66664H 373.28 Ea. 63.2 LPP R. WITH Legs, Double Row 1 24 71 66653H 223.65 Ea. 37.9 LPP 1 30 72 66654H 283.50 Ea. 48.0 LPP 1 36 73 66655H 344.93 Ea. 58.4 LPP 1 24 83 66656H 261.45 Ea. 44.3 LPP 1 30 84 66657H 330.75 Ea. 56.0 LPP 1 36 85 66658H 401.63 Ea. 68.0 LPP For Flat Top Lockers No Legs With 6" Legs For Unit SlopeTop Lockers No Legs With 6" Legs With Continuous Slope Hoods No Legs With 6" Legs Be sure to select the correct TYPE of Finished End Panel in the size required for the lockers. Each of the types shown on this page are different, and are not interchangeable! See the FEP introduction page for additional information. Reference the letter codes in the illustrations above to the product listings in the left column. Penco Products Inc. 47

Accessories, Packing House Lockers Partitions, Beaded Front, 24 Ga. For "Dual" lockers. Prices shown DO NOT include punching of shelf and bottom for attachment. For 9", " & 24" wide lockers ADD $2.25 to each partition for punching. Hooks need to be ordered separately. Depth shown is locker depth. For 60" Locker with 1 Shelf 50 P 653221C 44.90 Ea. 4.0 LPP 50 P 65323C 50.10 Ea. 5.0 LPP 50 P 65325C 55.60 Ea. 6.0 LPP 21 50 P 65327C 61. Ea. 7.0 LPP For 60" Locker with 2 Shelves 41 P 653201C 42.95 Ea. 4.0 LPP 41 P 653202C 49.00 Ea. 5.0 LPP 41 P 653203C 54.10 Ea. 6.0 LPP For 72" Locker with 1 Shelf 62 P 653232C 50.35 Ea. 5.0 LPP 62 P 65324C 54.95 Ea. 6.0 LPP 62 P 65326C 64.90 Ea. 8.0 LPP 21 62 P 65328C 75.50 Ea. 9.0 LPP 24 62 P 65330C 86.40 Ea. 10.0 LPP For 72" Locker with 2 Shelves 53 P 653204C 44.45 Ea. 5.0 LPP 53 P 653231C 53.65 Ea. 6.0 LPP 53 P 653205C 62.50 Ea. 7.0 LPP 21 53 P 653206C 73.85 Ea. 9.0 LPP Inner Compartment Doors Used with center partition and half shelves on 24" wide lockers. Includes door, hinge, compartment bottom, and knob. For lock, order # 9617, 9676 or 9709. Dimensions are nominal. For Executive Lockers 10 60511 52.90 Ea. 2.0 LPP 10 21 605 55.55 Ea. 2.2 LPP 10 24 60513 58.30 Ea. 2.4 LPP Interior Subdivisions for Executive Lockers For use with "Half Shelves" and/or Inner Compartment Doors on, 21 or 24" deep Lockers. Size D x H Price Wt. PARTITIONS - (Flanged Front) 24 Ga. FOR 60" LOCKER WITH ONE SHELF x 50 56.50 6.0 21 x 50 61.30 7.0 24 x 50 70.30 8.0 PARTITIONS - (Flanged Front) 24 Ga. FOR 72" LOCKER WITH ONE SHELF x 62 64.60 8.0 21 x 62 73.60 9.0 24 x 62 82.80 10.0 HALF SHELVES Size W x D Price Wt. 10 x 14.80 1.4 10 x 21.50 1.7 10 x 24 16.30 1.9 NOTE: The depth shown is the locker depth. Actual depth of partitions and shelves is 3" less than the locker depth to allow room for the latching mechanism. Miscellaneous Locker Accessories Comb & Brush Tray With Towel Bar Add $2.25 per door for punching holes to attach. 8 2 2 P 60841 21.00 Ea. 1.0 LPP Golf Ball Tray Locker depths are shown. Tray size is approximately 3" less than locker depth. 2 1-1/2 60851C 23.20 Ea. 1.0 LPP 2 21 1-1/2 60852C 23.50 Ea. 1.0 LPP 2 24 1-1/2 60853C 24.00 Ea. 1.0 LPP Acrylic Mirror With adhesive back; 1/8" thick. Cannot be attached to doors with diamond or visual perforations, minilouvers and quiet sound-deadening panels. 6 8 96370 14.90 Ea. 0.6 LPP Name Card Holder Size shown is card size. NOTE: Add $2.25 each to punch holes in door for attaching. 2-3/4 1-1/4 P 9446H 8.10 Ea. 0.2 LPP Stainless Steel Lock Strike Plate Includes hardware. Note that Strike Plate requires either field drilling or factory punching of the door. For factory punching add $2.25 each. 2-1 P 8669H 4.50 Ea. 0.1 LPP ADA Logo Label Pressure sensitive sticker. Shipped loose for field application. 8690 6.20 Ea. 0.1 LPP Concrete Floor Anchor For Lockers/Bench Pedestals 1/4 2 9680 1.30 Ea. 0.3 LPP Locker Shoe, Adjustable (For lockers with 6" legs.) 60807Z 3.25 Ea. 0.1 LPP Packing House Lockers Packing house legs raise lockers 16" above floor to facilitate cleaning. Designed for " & " wide Vanguard & Guardian lockers only - lockers MUST have standard 6" legs. Bench supports shown are for " deep lockers. NOTE: Price benches separately. Supply floor plan for bench lengths. Not available assembed. Packing House Kit for 1 Wide 16 64001 80.75 Kit 10.0 PPO Packing House Kit for 3 Wide 16 64003 104.90 Kit.0 PPO Rear Leg, Packing House Actual length is 25". Use 1 per bench support. 16 65540H 9.30 Ea. 1.0 LLP Bench Support Maximum 45" O.C., for " deep lockers. 65541H 21.00 Ea. 3.0 LLP End Front Leg Use one on each end of locker group. 16 65542H 9.95 Ea. 1.0 LLP Intermediate Front Leg To cover all intermediate legs. 16 65543H 11.90 Ea. 2.0 LLP 48 Penco Products Inc.

Benches & Pedestals / Introduction to Locks Wood Locker Room Benches Finished with 2 coats of clear lacquer. For fractional sizes, contact a Penco representative. Order Bench Pedestals separately. 36 9-1/2 1-1/4 9611 138.80 Ea. 13.0 LPP 48 9-1/2 1-1/4 9600 166.45 Ea. 16.0 LPP 60 9-1/2 1-1/4 9601 198.90 Ea. 20.0 LPP 72 9-1/2 1-1/4 9602 231.70 Ea. 24.0 LPP 84 9-1/2 1-1/4 9603 266.20 Ea. 29.0 LPP 96 9-1/2 1-1/4 9604 300.90 Ea. 32.0 LPP 108 9-1/2 1-1/4 9605 335.60 Ea. 38.0 LPP 0 9-1/2 1-1/4 9606 370.05 Ea. 42.0 LPP 132 9-1/2 1-1/4 9607 404.65 Ea. 46.0 LPP 144 9-1/2 1-1/4 9608 439.20 Ea. 50.0 LPP 48 1-1/4 9622 289.80 Ea. 24.0 LPP ADA Bench Note: 20 and 24 deep bench seats require 4 pedestals for optimum stability. 42 16 1-1/4 9634 329.25 Ea. 23.5 LPP 48 16 1-1/4 9635 339.70 Ea. 27.0 LPP 42 1-1/4 9625 332.25 Ea. 26.5 LPP 48 1-1/4 9628 343.90 Ea. 30.3 LPP 42 20 1-1/4 9636 362.75 Ea. 29.5 LPP 48 20 1-1/4 9632 364.65 Ea. 33.7 LPP 42 24 1-1/4 9624 360.40 Ea. 35.4 LPP 48 24 1-1/4 9623 377.35 Ea. 36.0 LPP Bench Pedestals Heavy Duty, Steel Tube w/ Flanges Must be Anchored to Floor Order 2 pedestals for benches through 96" long. Order three for benches over 96" up to 144". For longer benches, combine sizes. Hardware is supplied to fasten pedestal to bench only (see "Concrete Floor Anchor" #9680 in 'Locker Accessories'.) 16-1/4 60822H 49.50 Ea. 5.0 LPP Stainless Steel Pedestal For free-standing use, order one for each extreme end of benches up to a maximum length of 72". For fixed use (anchored to floor) use two pedestals for benches through 96" long, and three pedestals for benches over 96" to 144" long. Hardware is supplied to fasten pedestal to bench only. 14 16-1/4 60827H 146.35 Ea. 6.0 LPP Non-Skid Pedestal Kit Set of 4 rubber feet and fastening hardware for Stainless Steel Pedestal only. Order 1 set per pedestal. 68420.55 Ea. 1.0 LPP Bench Bracket ADA Bench Bracket with Hardware To provide a back support for ADA benches. For attaching 16" or " benches for use as backrests to 20" or 24" deep benches as seats. Must be used with a minimum of 4 bench pedestals. Steel construction available in 24 colors. 20 20 6ACXHP61H 98.20 Ea. 8.1 LPP Locks See 'Lock Application Table' on next page. The Following Applies to All Locks For lock group keying or masterkey series other than standard, or grand masterkeying, consult sales representative for pricing. On factory-assembled lockers, locks are packaged separately for installation on site. Lock Information Sheet Required for Master Lock & Zephyr Brands Master Lock Zephyr Penco Catalog # for Lock: Qty: Penco Catalog # for Master Key: Qty: (Order at least one master key if ordering built in combination locks) Locker/Handle type: Are these locks a continuation or addition to an existing system? Yes No If yes, existing master key number: End User of Locks: Name of Org: Job Name/Mark For: Street Address: Address Line 2: City, State Zip: Contact Info: Ship To Address Check if same as above: Ship to: Job Name/Mark For: Street Address: Address Line 2: City, State Zip: Contact Info: * * * After the order is placed with the lock vendor, changes/ cancellations cannot be made. Key Locks, Built-in, Flat Key Dead Bolt, 2 Keys Keyed Differently, fits RH or LH 9617 11.65 Ea. 0.3 LPP Dead Bolt, 4 Keys 9617-4 16. Ea. 0.5 LPP Dead Bolt, 2 Keys Keyed ALIKE, fits RH or LH For special series or group sets, contact a Penco Representative. 9670 10.65 Ea. 0.3 LPP Master Key, Flat 96171 6.00 Ea. 0.1 LPP Blank Key, Flat 9901 2.90 Ea. 0.1 LPP Penco Products Inc. 49

Lock Application Table Penco Part Number Lock Mfg. Number Lock Description NOTES Multi Point - All Single Point Latch - All Single Point Latch-ROTARY Cremone Turn Handle Friction Catch - All Spring Latch 2 Person RH 2 Person LH Duplex RH Duplex LH Patriot Duty Sec.Compartment Patriot Duty Drawer Patriot Turnout & Gear Sec.Box Patriot Turnout Footlocker Master 9678 1714 Grooved Key Spring Bolt 1 OK OK OK OK OK 9676 1710 Grooved Key Dead Bolt OK OK OK OK OK OK OK OK OK OK OK OK 96 1630 Combo Built in RH OK OK OK 9619 1631 Combo Built in LH OK OK 9653 1654 Combo Built in Spring RH 1 OK OK 9688 1652 Combo Built in Spring RH 1 OK OK OK 9659 1670 Combo Built in Dead Bolt RH OK OK OK OK OK OK 9654 02 Padlock OK OK OK OK OK OK OK OK OK OK OK 9655 25 Padlock OK OK OK OK OK OK OK OK OK OK OK 9676A 1710MKADA ADA Grooved Key Dead Bolt 3 OK OK OK OK OK OK OK OK OK OK 9693 1695MKADA ADA ROTARY lock Combo RH 4 OK 9698 1790MKADA ADA ROTARY Key lock RH 4 OK 9692 1690 ROTARY lock Combo RH 4 OK 9694 1790 ROTARY Key lock RH 4 OK Zephyr 9708 1754 Grooved Key Spring Bolt OK OK OK OK OK 9709 1770 Grooved Key Dead Bolt OK OK OK OK OK OK OK OK OK OK OK OK 9701 1930 Combo built in RH OK OK OK 9700 1931 Combo built in LH OK OK 9703 1954 Combo built in Spring RH 1 OK OK OK 9705 1970 Combo built in Dead Bolt RH OK OK OK OK 9706 1925 Padlock OK OK OK OK OK OK OK OK OK OK OK 9707 1730 ADA lock 3 OK 9700 1992 ROTARY Lock Combo RH 4 OK 50 Penco Products Inc. Electronic lock RFID Keypad OK OK OK OK OK OK OK OK OK OK OK Electronic lock RFID Cardlock OK OK OK OK OK OK OK OK OK OK OK Safe-O-Mat - S6 Coin Lock (96601) Flat Key Lock Coin Collect 2 OK OK OK Coin Return OK OK OK 9617 9617 Dead Bolt OK OK OK OK OK OK OK OK OK OK OK OK NOTES: Digi Lock "T" Series 3 OK OK OK OK OK OK OK OK OK OK OK 1 Optional: for improved security on 16 Person & Box Lockers, remove the padlock staple and hole in door. 2 If locker has recessed handles and latch channels, recessed handle adapter must be ordered. Minimum locker width ". 3 For ADA, use with Classic III Recessed Handle OR Defiant II Single Point latch handle with field removal of bullet catch. 4 When using a rotary lock, order a rotary latch. Field removal of bullet catch will be required for ADA. Note: For proper fit and security, the padlock shackle must have a diameter of 9/32 or 5/16 and a distance of.75 to.81 between the top of the case and the underside of the shackle when in the locked position.

Master Locks Key Locks, Built-in, Grooved Key Dead Bolt, Grooved: Master No. 1710MKRMVK, brass key 5 pin tumbler. Key removable in locked or unlocked position. 9676 31.25 Ea. 0.3 LPP Master Key, Grooved for 11710MKRMVK & 1714MKRMVK 96761 7.30 Ea. 0.1 LPP Extra Key, Grooved for 1710MKRMVK & 1714MKRMVK 9905 7.30 Ea. 0.1 LPP Spring Bolt, Grooved Key : Master No. 1714MKRMVK Recommended for Box Lockers only when hasp is cut off and slot is deleted. 9678 31.25 Ea. 0.3 LPP Combination Locks for Latch Channels Master No. 1630 R.H. Dial - Masterkey Control - Self Locking - RIGHT HAND HINGE only. 96 32.25 Ea. 0.1 LPP Master No. 1631 L.H. Dial - Masterkey Control - Self Locking - LEFT HAND HINGE only. Use for Left Hand hinged doors of 2 Person or Duplex, or any special LH hinged locker doors. 9619 32.25 Ea. 0.4 LPP Master key for 1630-31 961 7.30 Ea. 0.1 LPP Combination Lock - Box Lkrs, Spring Bolt Master No. 1654 R.H. (NOT for use on Defiant II) For Multiple Tier Box Lockers only - RIGHT HAND HINGE. See Master No. 1670 for greater security. 9653 35.95 Ea. 0.4 LPP Master Key for 1654 96531 7.30 Ea. 0.1 LPP Combination Lock for Defiant II SPL Master No. 1652 R.H., Spring Bolt 9688 35.95 Ea. 0.4 LPP Master key for No. 1652 Lock 96881 7.30 Ea. 0.1 LPP Combination Lock - Box Locker Dead Bolt Master No. 1670 R.H. Recommended for greater security for use on Box Lockers, unless the padlock loop is removed and the slot is left out of the door - contact a Penco representative for this application. Also recommended for Cremone handles. 9659 37.35 Ea. 0.4 LPP Master key for 1670 96591 7.30 Ea. 0.1 LPP Combination Padlocks Master No. 02 - Dial only, Not Masterkeyed 9654.45 Ea. 0.4 LPP Master No. 25 - Dial, Masterkey Control 9655.65 Ea. 0.4 LPP Master key for 25 96551 7.30 Ea. 0.1 LPP Master ADA Locks Master No. 1710MKADA; Lock & 2 keys. Built-in Grooved Key manual deadbolt with large key head. 9676A 33.25 Ea. 0.4 LPP Master key for 1710MKADA lock 9676A1 7.30 Ea. LPP Built-in combo, ROTARY Lock, master keyed, RH (Master No. 1695MKADA) 9693 54.55 Ea. LPP Master key for 1695MKADA lock (Master No. K1695CM) 96931 7.30 Ea. LPP Grooved Key Lock, ROTARY Lock, with ADA key head, RH (Master No. 1790MKADA) 9698 41.50 Ea. LPP Master key for 1790 lock (Master No. K1710W81KM) 96981 7.30 Ea. LPP Locks - Master & Zephyr Brands Combination Lock - Defiant II ROTARY Latch Only Built-in Combination Lock - to be used with Defiant II w/ Rotary Latch Only: Master No. 1690 RH 9692 42. Ea. 0.6 Control Key for No. 1690 96921 7.30 Ea. Grooved Key Lock - Defiant II ROTARY Lock, RH To be used with Defiant II w/ ROTARY latch only. (Master No. 1790) 9694 31.05 Ea. LPP Master key for 1790 lock (Master No. K1710W81KM) 96941 7.30 Ea. LPP Zephyr Locks Key Locks, Built-in, Grooved Key Built-in Key Lock, Dead Bolt: Zephyr No. 1770 9709 14.00 Ea. 0.4 Control key for No. 1770 97091 4.70 Ea. Key Locks, Built-in, Spring Bolt For Box Lkrs, Grooved Key Built-in Key Lock, Spring Bolt: Zephyr No. 1754 9708 14.00 Ea. 0.4 Control key for 1754 97081 4.70 Ea. Combination Locks for Latch Channels Zephyr No. 1930 R.H. Dial - Masterkey Control - Self Locking - RIGHT HAND HINGE only. NOTE: When ordered through the QuickShip program, this item drop ships from Zephyr. 9701 19.35 Ea. 0.4 Zephyr No. 1931 L.H. Dial - Masterkey Control - Self Locking - LEFT HAND HINGE only. Use for Left Hand hinged doors of 2 Person or Duplex, or any special LH hinged locker doors. 9700 19.35 Ea. 0.4 Master key for Zephyr Combination Locks NOTE: When ordered through the QuickShip program, this item drop ships from Zephyr. 97011 4.70 Ea. Combination Locks-Box Lkrs, Spring Bolt Zephyr No. 1954 R.H. For Multiple Tier Box Lockers. See Zephyr No. 1970 for greater security on Box Lockers. RIGHT HAND HINGE only. 9703 21.35 Ea. 0.4 LPP Control key for Zephyr # 1954 9714 4.70 Ea. Combination Locks-Box Locker Dead Bolt Zephyr No. 1970 R.H. Recommended for greater security for use on Box Lockers, unless the padlock loop is removed and the slot is left out of the door. Contact a Penco representative for this application. 9705 22.00 Ea. 0.4 LPP Control key for No. 1970 9713 4.70 Ea. Combination Padlock Zephyr No. 1925. Dial - Masterkey Control - - - 9706 9.35 Ea. 0.4 LPP Control key for Zephyr No. 1925 97061 4.70 Ea. Zephyr ADA Locks Zephyr No. 1730: Lock and 3 keys. Built-in Grooved Key vertical deadbolt with large key head for latch channel lockers only. Requires key insertion, but no rotation. 9707 29.20 Ea. 0.4 LPP Zephyr No. 1730: Extra Key for Zephyr 1730 97001 29.35 Ea. 0.1 LPP Control key for Zephyr 1730 97000 29.35 Ea. 0.1 LPP Combination Lock - Defiant II ROTARY Latch Only Built-in Combination Lock - to be used with Defiant II w/ Rotary Latch Only: Zephyr No. 1992 R.H. 9700 26.55 Ea. 0.6 Control key for No. 1992 97 4.70 Ea. Zephyr RFID Battery powered locks with card or keypad operation for ADA and managed access applications. Refer to a Penco representative for pricing and additional information. 51

Digilock Battery powered locks with key fob or keypad operation for ADA and managed access applications. Refer to a Penco representative for pricing and additional information. Safe-O-Mat Coin Operated Locks S-6 Safe-O-Mat Lock Includes 1 user key, correct coin decal and front instruction decal. 96601 2.90 Ea. 1.0 LPP Master Key for Lock Opens locker, drops coin. Relocks w/o additional coin. (NOT included with lock.) 96603 61.75 Ea. 0.1 LPP Cash Box for Coin Collect Must order keys separately. Door must be field drilled for installation. 96602 77.10 Ea. 1.0 LPP Cash Box Key Opens cash box. (Not included with cash box or lock - must be ordered separately.) 96606 26.55 Ea. 0.1 LPP Lock Cylinders Order 5-10% of quantity of locks ordered (instead of extra keys). 96604 88.90 Ea. 0.3 LPP Recessed Adapter for Coin Lock For Classic III stainless steel RECESSED HANDLES without quiet or reinforcing pans in door. 96617 32.40 Ea. 1.0 LPP Number Tags Set of 50 tags. Tags to attach to keys. 50 tags per set (must be ordered in sets of 50). 96605 131.65 Set 0.1 LPP Safe-O-Mat Parts/Accessories Token - Brass Order 2-3 times the quantity of locks. 96613 3.70 Ea. 0.1 LPP Tool Kit for S-6 Coin lock Must be ordered separately; installs locks and uninstalls locks with the aid of Torx driver (not included). One kit supplied free with order of 100 or more locks. 966 0.25 Ea. 0.7 LPP Torx Driver Must be ordered separately (unassembles and assembles locks). One free with order of 10 or more locks. 96616 24.60 Ea. 0.4 LPP Decal - "1 Quarter" One supplied with lock. Extra decals avail. only in sheets of 54 decals. 96607 447.95 Sheet 0.1 LPP Decal - "2 Quarters" One supplied with lock. Extra decals avail. only in sheets of 54 decals. 96608 447.95 Sheet 0.1 LPP Decal - "1 Token" One supplied with lock. Extra decals avail. only in sheets of 54 decals. 96609 447.95 Sheet 0.1 LPP Digilocks / Safe-O-Mat Coin Operated Locks Decal - Instructions for Inside of locker door One decal is supplied with appropriate lock for INSIDE locker door. For extra decals, a minimum order of 25 decals is required. 966 8.30 Ea. 0.1 LPP Decal - "Coin Return" Instructions for Outside of locker door. Decal for outside of locker door is NOT supplied with lock - must be ordered separately. A minimum order of 25 decals is required. 96610 8.30 Ea. 0.1 LPP Decal - "Coin Collect" Instructions for Outside of locker door. Decal for outside of locker door is NOT supplied with lock - must be ordered separately. A minimum of 25 decals is required. 96611 8.30 Ea. 0.1 LPP Safe-O-Mat Ordering Information Order keys numbered 1-up. Order 5-10% extra lock cylinders (not user keys) for each job. Order masterkey/penalty type as needed. IMPORTANT: When ordering Safe-O-Mat locks please include the following information: 1. Quantity & Lock Model # 2. Coin Collect or Return 3. Dead bolt or Spring bolt 4. 1 Quarter, 2 Quarter or token 5. Numbering sequence for key tags: a. b. None 6. Quantity of Master Keys and name of recipient 7. Quantity of Cash Box Keys 8. Quantity of extra cylinder locks (5-10% recommended) 9. Any additional accessories required 10. Shipping address & delivery date 11. Name and address of ultimate end user. If order is to add locks to an existing installation, advise existing series number. LOCKER REQUIREMENTS: When used with Classic III stainless steel recessed handles, order No. 96617 Adapter. Do NOT use Safe-O-Mat locks with the following lockers: Defiant II Lockers. Lockers with left hand hinges (hinge on left side) Two-Person or Duplex lockers Locker doors less than " wide Lockers with Slam Latches. Lockers with quiet pans, Lockers with mini-louvers or perforated doors Safe-O-Mat Prices are F.O.B. Destination 52 Penco Products Inc.

Door and Frame Assemblies (Except Patriot) Vanguard Locker Door & Frame Assemblies Vanguard Handle included with 1Tier, 2Tier, plus 2 Person & Duplex D&F Assemblies. NOT included are: Number Plates (86H), Lock Hole Cover Plate for 1 & 2 Tier Lockers (60811Z), and Door Pulls (60803Z) for 1-6 tier. See "Misc. Locker Parts for Doors" for these. (Height shown INCLUDES 6" legs for those items with legs.) 1 Tier (without Legs) 30-1/2 65930XC 0.40 Ea. 14.0 LPP 36-1/2 6595XC 6.40 Ea..8 LPP 48-1/2 67000XC 5.65 Ea. 20.0 LPP 9 60 620XC 5.40 Ea. 21.0 LPP 60 660XC 172.00 Ea. 24.0 LPP 60 61300XC 193. Ea. 28.0 LPP 60 61340XC 233.60 Ea. 31.0 LPP 24 60 61420XC 286.50 Ea. 39.3 LPP 9 72 640XC 167.90 Ea. 26.0 LPP 72 680XC 194.45 Ea. 28.0 LPP 72 61320XC 2.90 Ea. 34.0 LPP 72 61360XC 241.60 Ea. 38.0 LPP 24 72 61460XC 303.95 Ea. 46.0 LPP 1 Tier, DOUBLE DOOR, Vanguard ONLY (no Legs) 24 60 Y 61430XC 335.50 Ea. 44.0 LPP 24 72 Y 61470XC 355.20 Ea. 51.0 LPP 1 Tier (with Legs) 36-1/2 65920XC 0.40 Ea. 14.7 LPP 42-1/2 66950XC 6.40 Ea. 17.0 LPP 54-1/2 67100XC 5.65 Ea. 21.0 LPP 9 66 630XC 5.40 Ea. 22.0 LPP 66 670XC 172.00 Ea. 26.0 LPP 66 61310XC 193. Ea. 30.0 LPP 66 61350XC 233.60 Ea. 33.0 LPP 24 66 61440XC 286.50 Ea. 43.0 LPP 9 78 650XC 167.90 Ea. 27.0 LPP 78 690XC 194.45 Ea. 29.0 LPP 78 61330XC 2.90 Ea. 36.0 LPP 78 61370XC 241.60 Ea. 40.0 LPP 24 78 61480XC 303.95 Ea. 51.0 LPP 1 Tier, DOUBLE DOOR, Vanguard ONLY (with Legs) 24 66 Y 61450XC 335.50 Ea. 48.0 LPP 24 78 Y 61490XC 355.20 Ea. 55.0 LPP 2 Tier (without Legs) 9 60 62190XC 170.35 Ea. 23.0 LPP 60 62230XC 190.40 Ea. 26.0 LPP 60 62290XC 211.85 Ea. 29.0 LPP 60 62350XC 236.00 Ea. 32.0 LPP 9 72 62210XC 6.05 Ea. 25.0 LPP 72 62250XC 201.40 Ea. 30.0 LPP 72 62310XC 228.10 Ea. 35.0 LPP 72 62370XC 258.40 Ea. 38.0 LPP 24 72 62410XC 435.10 Ea. 48.0 LPP 84 62270XC 2. Ea. 35.0 LPP 84 62330XC 249.35 Ea. 39.0 LPP 2 Tier (with Legs) 9 66 62200XC 170.35 Ea. 24.0 LPP 66 62240XC 190.40 Ea. 27.0 LPP 66 62300XC 211.85 Ea. 30.0 LPP 66 62360XC 236.00 Ea. 39.0 LPP 9 78 62220XC 6.05 Ea. 26.0 LPP 78 62260XC 201.40 Ea. 31.0 LPP 78 62320XC 228.10 Ea. 36.0 LPP 78 62380XC 258.40 Ea. 45.5 LPP 24 78 62420XC 435.10 Ea. 49.0 LPP 90 62280XC 2. Ea. 36.0 LPP 90 62340XC 249.35 Ea. 40.0 LPP 3 Tier, w/latch Chan (without Legs) 60 638XC 224.80 Ea. 23.4 LPP 72 64077XC 242.95 Ea. 31.2 LPP 3 Tier, w/latch Chan (with Legs) 66 637XC 224.80 Ea. 24.4 LPP 78 64078XC 242.95 Ea. 31.6 LPP 3 Tier Box Doors (without Legs) 9 60 63071XC 177.55 Ea. 20.0 LPP 60 63075XC 195.50 Ea. 23.0 LPP 9 72 63073XC 8.65 Ea. 23.0 LPP 72 63077XC 211.25 Ea. 27.0 LPP 72 63079XC 233.40 Ea. 31.0 LPP 72 63081XC 259.00 Ea. 35.5 LPP 3 Tier Box Doors (with Legs) 9 66 63072XC 177.55 Ea. 21.0 LPP 66 63076XC 195.50 Ea. 24.0 LPP 9 78 63074XC 8.65 Ea. 24.0 LPP 78 63078XC 211.25 Ea. 28.0 LPP 78 63080XC 233.40 Ea. 32.0 LPP 78 63082XC 259.00 Ea. 36.5 LPP 4 Tier Box Doors (without Legs) 60 63210XC 209.05 Ea. 24.0 LPP 72 632XC 225.85 Ea. 28.0 LPP 4 Tier Box Doors (with Legs) 66 63211XC 209.05 Ea. 25.0 LPP 78 63213XC 225.85 Ea. 29.0 LPP 5 Tier Box Doors (without Legs) 60 63281XC 225.65 Ea. 24.0 LPP 60 63285XC 261.05 Ea. 28.0 LPP 72 63283XC 250.30 Ea. 24.0 LPP 72 63287XC 276.40 Ea. 34.0 LPP 5 Tier Box Doors (with Legs) 66 63282XC 225.65 Ea. 25.0 LPP 66 63286XC 261.05 Ea. 29.0 LPP 78 63284XC 250.30 Ea. 31.0 LPP 78 63288XC 276.40 Ea. 35.0 LPP 6 Tier Box Doors (without Legs) 72 63366XC 264.90 Ea. 29.0 LPP 72 63368XC 291.35 Ea. 33.0 LPP 72 63370XC 336.10 Ea. 38.0 LPP 6 Tier Box Doors (with Legs) 78 63367XC 264.90 Ea. 30.0 LPP 78 63369XC 291.35 Ea. 34.0 LPP 78 63371XC 336.10 Ea. 39.0 LPP Box Over (without Legs) 60/72 65708XC 252.90 Ea. 31.0 LPP 60/72 65710XC 280.75 Ea. 34.2 LPP 60/72 657XC 314.10 Ea. 39.0 LPP Box Over (with Legs) 60/78 65707XC 252.90 Ea. 31.0 LPP 60/78 65709XC 280.75 Ea. 35.0 LPP 60/78 65711XC 314.10 Ea. 40.0 LPP Standard Catalog DOOR & FRAME Pricing Find size and type needed and add amount shown below to the Vanguard base price shown above. Vanguard Locker Door & Frame Assembly Base price (shown above) Recessed Vanguard Standard RH Standard Guardian Standard Guardian Medallion Base price (shown above) Base price (shown above) Base price + Pan Pricing on page 31 NOTE: Horizontal frame members were added between the doors of Standard Invincible II & Guardian Plus Base price + $58.85 2 & 3-tier lockers in late 1996. Use of newer door & frame assemblies on bodies made prior to that will require replacing the intermediate Defiant II (Guardian & Invincible II) Base price + $62.10 shelves with TABs (Tops And Bottoms) between the tiers. Penco Products Inc. 53

Door & Frame Assemblies (Ex. Patriot), Misc. Locker Parts for Doors Vanguard 2 Person Locker D&F Assemblies 2 Person (without Legs) 60 65605EC 350.35 Ea. 32.0 LPP 72 65611EC 349.30 Ea. 39.0 LPP 2 Person (with Legs) 66 65608EC 350.35 Ea. 33.0 LPP 78 65614EC 349.30 Ea. 40.0 LPP Two Person Door & Frame Parts Vanguard Upper Book Door Assembly 2P (1) 9 65595EC 38.80 Ea. 3.0 LPP Vanguard Lower Book Door Assemby 2P (2) 9 65592EC 38.80 Ea. 3.0 LPP Vanguard Coat Door Assembly 2P, Rt. Side (3) (Handle Included) 7-1/2 54 65568EC 142. Ea. 10.0 LPP Vanguard Coat Door Assembly 2P, Left Side (4) (Handle Included) 7-1/2 54 65572EC 142. Ea. 10.0 LPP Vanguard Latch Channel Assembly R.H. (5) 65263C 36.35 Ea. 1.0 LPP Vanguard Latch Channel Assembly L.H. (6) 65265C 36.35 Ea. 1.0 LPP Latch Channel Assembly Bottom (7) 65268C 7.30 Ea. 1.0 LPP Latch Channel Assembly Top (8) 65267C 7.30 Ea. 1.0 LPP Locking Device Assembly L.H. (9) 60860C 24.25 Ea. 1.0 LPP Locking Device Assembly R.H. (10) 60861C.00 Ea. 1.0 LPP Replacement Clip (11) Guide for locking device assembly, LH & RH, AFTER 4/84. 608651C 2.60 Ea. 0.1 LPP Two Person Locker Parts Lower Tier Head, 2 Person 651179C 17.65 Ea. 1.9 LPP 6511C 21.80 Ea. 2.3 LPP 21 6513C 24.10 Ea. 2.6 LPP Partitions, 2 Person Locker 54 65277C 53.90 Ea. 6.0 LPP 54 65279C 62.95 Ea. 7.1 LPP 21 54 65281C 74.35 Ea. 8.3 LPP Latch Channel Assemblies - Vanguard Handle Only Single Tier - 48" 48 626578C 30.80 Ea. 1.5 LPP Single Tier - 60" 626C 38.50 Ea. 2.4 LPP Single Tier - 72" 628C 44.90 Ea. 2.7 LPP Double Tier - 30" 30 626572C 20.90 Ea. 1.0 LPP Double Tier - 36" 36 626574C 24.05 Ea. 1.0 LPP Three Tier - 20" 20 63003C 20.20 Ea. 1.0 LPP Three Tier - 24" 24 63000C 20.90 Ea. 1.0 LPP Latch Channel Assemblies - Classic III Rec. Handle Only For use on right-hinged KD and Welded lockers. Single Tier - 48" 48 626578RC 39.85 Ea. 2.5 LPP Single Tier - 60" 60 626RC 47.50 Ea. 3.4 LPP Single Tier - 72" 72 628RC 53.90 Ea. 3.7 LPP Double Tier - 30" 30 626572RC 29.90 Ea. 2.0 LPP Double Tier - 36" 36 626574RC 33.05 Ea. 2.0 LPP Three Tier - 20" 20 63003RC 29.20 Ea. 2.0 LPP Three Tier - 24" 24 63000RC 29.90 Ea. 2.0 LPP Miscellaneous Locker Parts for Doors Lock Hole Cover Plate Used without built-in locks, not for box lockers. 60811Z 2.50 Ea. 0.1 LPP Vanguard Handle with Palnut 8658H.95 Ea. 0.3 LPP Vanguard Handle (no Palnut) Palnut NOT included. 8658.85 Ea. 0.3 LPP Palnut for Vanguard Handle 1 required per each handle 8642 0.20 Ea. 0.1 LPP Extra Number Plate, Without Rivets (1-1000) Blank, or from 1 to 1000. 86 2. Ea. 0.1 LPP Extra Number Plate, With 2 Rivets (1-1000) Blank, or from 1 to 1000. 86H 2.35 Ea. 0.1 LPP Pop Rivet for Number Plate Pop rivet gun is required for installation. 8671 0.10 Ea. 0.1 LPP Number Plate, Alpha Numeric or Above 00 WithOUT Rivets. Number Plate (anything other than 1 to 1000 or blank). 6 spaces maximum. Allow 4-5 weeks. Add $50 NET setup charge per order. P 8616 2. Ea. 0.1 LPP WITH Rivets. Number Plate (anything other than 1 to 1000 or blank). 6 spaces maximum. Allow 4-5 weeks. Add $50 NET setup charge per order. P 8616H 2.35 Ea. 0.1 LPP 54 Penco Products Inc.

Miscellaneous Locker Parts (Except Patriot) Coiled Spring for Latch Clip 2 on 2 Tier, 3 on 1-Tier 8650 0.25 Ea. 0.1 LPP Nylon Latch Clip 8651 0.70 Ea. 0.1 LPP Knurled Pin 8652NK 0.20 Ea. 0.1 LPP Retaining Button for Latch Channel 2 required per door (was "Spiral Pin") 8655L 0.50 Ea. 0.1 LPP Nut Driver - 3/8" For 10-24 Nuts or Palnut #8642 9630.40 Ea. 0.4 LPP Door Pull 1 per box locker door 60803Z 4.70 Ea. 0.2 LPP Locker Hinge, 2" High, 5-Knuckle Unpainted. Welding required. 8620 0.95 Ea. 0.2 LPP Rivet; Locker Door to Hinge Also used to fasten Latch Channel to lift piece for Classic III & Classic II recessed pockets. 8621 0.20 Ea. 0.2 LPP Rivet; Continuous Hinge to Door Frame 3/16 8619 0.20 Ea. 0.1 LPP Shoulder Rivet, Double Door Locker 8681 2. Ea. 0.1 LPP Top Spring, Double Door Locker 8683 1.25 Ea. 0.1 LPP Bottom Spring, Double Door Locker 8684 1.25 Ea. 0.1 LPP Top Cam Assy., 24" Wide Double Door Lkr. 60843C 5.95 Ea. 0.1 LPP Bottom Cam Assy. 24" Wide Double Door Lkr. 60844C 5.95 Ea. 0.2 LPP Decorative Fastener For Rec. Hndl. After 1/88 9685 0.25 Ea. 0.1 LPP Locknut for Decorative Fastener 96851 0.10 Ea. 0.1 LPP Lift Piece Assy., L.H. For Classic II & III Recessed Pocket 608940C 9.00 Ea. 1.0 LPP Lift Piece Assy., R.H. 608930C 9.00 Ea. 1.0 LPP Classic III Recessed Pocket, Stainless NO Number Plate holes. First used in 2000. 60890C 14.90 Ea. 0.8 LPP Classic III Rec. Pocket, Stainless, w/hdwr NO Number Plate holes. First used in 2000. 60890H.50 Ea. 0.8 LPP Plastic Lift Piece for Classic III Rec. Handle Shipped unpainted. 9687 2.00 Ea. 0.3 LPP Rivet for Plastic Lift Piece #9687 8677 0.50 Ea. 0.1 LPP Defiant II SPL Pocket, Stainless 60877MD.50 Ea. 0.7 LPP Defiant II SPL Pocket, Stainless, W/Hdwr 60877MH.60 Ea. 0.7 LPP Defiant II Pocket for Rotary Lock (No padlock slot) 608772.50 Ea. 0.7 LPP Miscellaneous Locker Parts Single Prong Wall Hook 8697 0.50 Ea. 0.1 LPP Double Prong Ceiling Hook 8698 2.10 Ea. 0.2 LPP Single Prong Wall Hook For use with Coat Rod 8699 1.40 Ea. 0.1 LPP Single Prong Coat Hook, WELDED Locker Only Fastens to shelf at side 8696 5.10 Ea. 0.1 LPP Coat Rods 1/2" diameter thru 24" long. 3/4" diameter for 45". 7-1/2 8660 8.40 Ea. 0.2 LPP 9 8661 9.70 Ea. 0.2 LPP 8662 11.05 Ea. 0.3 LPP 8664 13.90 Ea. 0.3 LPP 8665 14.10 Ea. 0.4 LPP 24 8667 14.60 Ea. 0.5 LPP 45 8645 20.50 Ea. 1.1 LPP Coat Rod Bracket For 16 Person 60820Z 4.85 Ea. 0.3 LPP Coat Rod Bracket for Welded Locker 2 required per coat rod. Order 1/2" diameter coat rod and hardware separately. 6ACXH76Z 4.85 Ea. 0.3 LPP Coat Rod Retainer For Wall Mount Unit 60869Z 4.45 Ea. 0.3 LPP Standard 6" Rear Leg Actual ht. ". Also used with 6" Zee Base. 60091C 7. Ea. 0.7 LPP Top Trim Clip For Recessed Trim 60457Z 2. Ea. 0.1 LPP Wall Clip Used to anchor top of (flat top) locker to wall. 4-1/2 60856Z 2.35 Ea. 0.2 LPP Rubber Bumper 1 per latch hook 8606 0.30 Ea. 0.1 LPP Rubber Bumper for SPL Defiant II Door Frame Requires Rivet # 8671 to fasten (order rivet separately). 86051 0.30 Ea. 0.1 LPP Rubber Bumper for Footlocker Lid On Stadium & Patriot lockers. 8605 0.30 Ea. 0.1 LPP L. H. Latch Hook For use on 2-Person & Duplex ONLY. 60804 2.50 Ea. 0.2 LPP R. H. Latch Hook 2 per door on 2 Tier. 3 on 1 Tier 60805 2.50 Ea. 0.2 LPP Hook Plate for Diamond Perforated Side For bolting hook to locker side at row end. 60497Z 3.25 Ea. 0.1 LPP Padlock Staple, R. H. Box Locker 60801C 2.35 Ea. 0.2 LPP SPL Bracket Support for Defiant II KD Only 608710Z 2.50 Ea. 0.4 LPP Anti-Pry/Lock Alignment Bracket Fastens behind Defiant II Pocket. 3-1/2 2-11/16 60881Z 2.50 Ea. 0.3 LPP Penco Products Inc. 55

Miscellaneous Locker Parts (Except Patriot) Defiant II Side Stiffener for KD Lockers Mounts to Division & Hasp 60871H 9.20 Ea. 1.5 LPP 60871H 11.50 Ea. 1.8 LPP 60871H 13.85 Ea. 2.0 LPP 21 6087211H 16.70 Ea. 2.3 LPP 24 6087241H.50 Ea. 2.5 LPP Anchor Bracket for Welded Locker w/ Channel Base 1 3 1/8 P501Z 6.60 Ea. 0.5 LPP Replacement Hardware Slotless Locker Bolt 10-24 3/8 8632H 3.60 100 2.0 100 1/2 8633H 5.35 100 1.3 100 Hex Nut 10-24 8672H 1.90 100 1.2 100 Keps Nut 10-24 8604H 7.45 100 2.0 100 Sheet Metal Screw 8603H 3.60 100 1.4 100 Lag Screw, 1/4" x 1" (for locker bench) 1 8624H 14.30 100 4.0 100 Machine Screw, 1/4-20 x 1-1/4" TR HD 1-1/4 8101H 10.65 100 4.0 100 Push-In Washer, Threaded For fastening Wall Mount Locker Coat Rod 3/4 8685 1.55 Ea. 0.1 LPP Rivet for Locker Assembly Use for Bodies and Frames Note: All KD lockers shipped w/nuts & bolts as standard. - - - 8676 0.25 Ea. 0.1 LPP Defiant II Rotary Hasp Conversion Kits For Spring Bolt Built-in Lock To convert a "Defiant II-R rotary hasp" on a single point latch locker for use with a built-in spring bolt lock. Hardware included. See illustration. 6ACXHM08H 22.70 Ea. 0.4 LPP For Padlock To convert a "Defiant II-R rotary hasp" on a single point latch locker for use with a padlock. Includes a new recessed pocked with slot for hasp and hardware. See illustration. 6ACXHM10H 33.65 Ea. 0.7 LPP Conversion Kits for Lockers with the Defiant II-R Optional Hasp These conversion kits are designed to convert a Defiant II locker with the optional Defiant II-R special hasp for Rotary, or wraparound, style locks to be used with a standard spring bolt lock or padlock instead. Both of these kits are illustrated below. The prices are above. Locker Backs - 24 Ga. For Flat Top Vanguard/Guardian, All Types 30-1/2 6003510EC 26.75 Ea. 2.8 LPP 36-1/2 600360EC 42.25 Ea. 3.6 LPP 48-1/2 6003700C 56.70 Ea. 4.5 LPP 9 60 60029C 35.45 Ea. 4.2 LPP 60 60037C 41. Ea. 5.3 LPP 60 60047C 42.95 Ea. 6.8 LPP 60 60055C 54.10 Ea. 7.6 LPP 24 60 60071C 71.20 Ea. 9.7 LPP 9 72 60033C 53.65 Ea. 5.2 LPP 72 60042C 64.90 Ea. 6.6 LPP 72 60051C 71.05 Ea. 7.8 LPP 72 60059C 77.70 Ea. 9.1 LPP 24 72 60075C 101.20 Ea. 11.9 LPP For Slope Top, Vanguard/Guardian,All Types 9 77 60035C 53.65 Ea. 5.6 LPP 9 78 60036C 54.20 Ea. 5.7 LPP 64 60038C 53.30 Ea. 5.6 LPP 65 60039C 55.30 Ea. 5.8 LPP 66 60040C 58.80 Ea. 6.2 LPP 21 67 60041C 71.70 Ea. 6.3 LPP 76 60043C 63.30 Ea. 6.8 LPP 77 60044C 64.25 Ea. 6.9 LPP 78 60045C 64.90 Ea. 7.0 LPP 21 79 60046C 82.70 Ea. 7.4 LPP 65 60048C 76.70 Ea. 7.5 LPP 66 60049C 77.50 Ea. 7.6 LPP 21 67 60050C 78.90 Ea. 7.7 LPP 77 60052C 71.05 Ea. 8.3 LPP 78 60053C 71.50 Ea. 8.4 LPP 21 79 60054C 73. Ea. 8.6 LPP 66 60056C 82.20 Ea. 8.9 LPP 21 67 60057C 83.70 Ea. 9.1 LPP 24 68 60058C 84.90 Ea. 9.2 LPP 77 600590C 96.00 Ea. 10.4 LPP 78 60060C 97.80 Ea. 10.6 LPP 21 79 60061C 98.75 Ea. 10.7 LPP 24 80 60062C 100.75 Ea. 10.9 LPP 24 66 60072C 1.50 Ea. 11.7 LPP 24 21 67 60073C 0.35 Ea. 11.9 LPP 24 24 68 60074C 1.50 Ea..0 LPP 24 78 60076C 139.55 Ea. 13.8 LPP 24 21 79 60077C 141.00 Ea. 14.0 LPP 24 24 80 60078C 143.50 Ea. 14.2 LPP Locker Backs - ga, Flat Top For Invincible II Locker Only 36-1/2 600301C 50.65 Ea. 6.7 LPP 48-1/2 600302C 68.05 Ea. 8.7 LPP 9 60 600000C 42.60 Ea. 8.4 LPP 60 600010C 49.40 Ea. 10.8 LPP 60 600011C 51.60 Ea. 13.2 LPP 60 6000C 65.00 Ea..6 LPP 24 60 600014C 85.45 Ea. 20.4 LPP 9 72 6000C 64.40 Ea. 10.1 LPP 72 600016C 77.90 Ea. 13.0 LPP 72 600017C 85.30 Ea..8 LPP 72 6000C 92.00 Ea..7 LPP 24 72 600020C 1.50 Ea. 24.4 LPP 56 Penco Products Inc.

Divisions, Flat Top-24 Ga. 30-1/2 6080EC 35.65 Ea. 2.3 LPP 36-1/2 601600EC 38.50 Ea. 2.8 LPP 48-1/2 601400C 41.60 Ea. 3.7 LPP 30-1/2 601780EC 42.00 Ea. 2.6 LPP 36-1/2 601660EC 45.05 Ea. 3.1 LPP 48-1/2 601410C 48.30 Ea. 4.1 LPP 30-1/2 601790EC 49.60 Ea. 3.6 LPP 36-1/2 601720EC 53.70 Ea. 4.3 LPP 48-1/2 601420C 57.95 Ea. 4.7 LPP Universal Divisions, Flat Top-24 Ga. 60 60163C 47.05 Ea. 4.4 LPP 60 60169C 50.45 Ea. 5.6 LPP 60 60175C 54.20 Ea. 6.8 LPP 21 60 601C 65.40 Ea. 8.4 LPP 24 60 6053C 84.90 Ea. 9.7 LPP 72 63376C 49. Ea. 5.2 LPP 72 63380C 54.95 Ea. 6.7 LPP 72 63384C 65.45 Ea. 8.2 LPP 21 72 63388C 79.30 Ea. 9.7 LPP 24 72 63372C 89.35 Ea. 11.5 LPP 84" High Only 84 62429C 50.70 Ea. 6.5 LPP 84 62441C 61.85 Ea. 7.5 LPP 84 62453C 72.00 Ea. 8.5 LPP Universal Divisions, Slope Top, (SR), LH-24 Ga. 64 60164C 53.65 Ea. 5.0 LPP 65 60170C 62.80 Ea. 6.0 LPP 66 60176C 70.10 Ea. 7.5 LPP 21 67 6011C 105.65 Ea. 9.4 LPP 24 68 6054C 3.55 Ea. 11.0 LPP Divisions, Slope Top - 24 Ga. For Half Height 1-Tier Left Hand 34-1/2 601920EC 46.50 Ea. 2.6 LPP 40-1/2 601610EC 50.20 Ea. 2.9 LPP 52-1/2 6014110C 54.25 Ea. 2.9 LPP 35-1/2 601960EC 54.85 Ea. 3.4 LPP 41-1/2 601670EC 58.75 Ea. 3.5 LPP 53-1/2 6014130C 63.00 Ea. 3.5 LPP 36-1/2 601980EC 64.70 Ea. 4.3 LPP 42-1/2 601730EC 70.00 Ea. 4.9 LPP 54-1/2 60140C 75.55 Ea. 4.9 LPP Right Hand 34-1/2 601930EC 46.50 Ea. 2.6 LPP 40-1/2 601620EC 50.20 Ea. 2.9 LPP 52-1/2 60140C 54.25 Ea. 2.9 LPP 35-1/2 601970EC 54.85 Ea. 3.4 LPP 41-1/2 601680EC 58.75 Ea. 3.5 LPP 53-1/2 6014140C 63.00 Ea. 3.5 LPP 36-1/2 601990EC 64.70 Ea. 4.3 LPP 42-1/2 601740EC 70.00 Ea. 4.9 LPP 54-1/2 6014160C 75.55 Ea. 4.9 LPP Universal Divisions, Slope Top, (SR), LH-24 Ga. 76 63377C 57.65 Ea. 5.6 LPP 77 63381C 69.05 Ea. 7.3 LPP 78 63385C 77.90 Ea. 8.3 LPP 21 79 63389C 103.60 Ea. 10.7 LPP 24 80 63373C 132.80 Ea..9 LPP Divisions (locker sides) - Except Patriot Universal Divisions, Slope Top, (SR), RH-24 Ga. 64 60165C 53.65 Ea. 5.0 LPP 65 60171C 62.80 Ea. 6.0 LPP 66 60177C 70.10 Ea. 7.5 LPP 21 67 60C 105.65 Ea. 9.4 LPP 24 68 6055C 3.55 Ea. 11.0 LPP 76 63378C 57.65 Ea. 5.6 LPP 77 63382C 69.05 Ea. 7.3 LPP 78 63386C 77.90 Ea. 8.3 LPP 21 79 63390C 103.60 Ea. 10.7 LPP 24 80 63374C 132.80 Ea..9 LPP Penco Products Inc. 57

Miscellaneous Locker Parts (Except Patriot), Basket Racks Unit Slope Tops For 2 Tier. 24 Ga. With Coat Hook Holes (Use for replacement parts only) 9 62670C 11.50 Ea. 1.0 LPP 9 62671C.40 Ea. 2.0 LPP 9 62672C 14.80 Ea. 2.0 LPP 62673C.40 Ea. 2.0 LPP 62674C.50 Ea. 2.0 LPP 62675C 14.90 Ea. 3.0 LPP 62676C 14.80 Ea. 3.0 LPP 62677C.55 Ea. 3.0 LPP Tops & Bottoms, 24 Ga. (Flat Top) Also used to separate compartments on 2 & 3 tier lockers mfg. since 1995. 9 60910C 13.25 Ea. 1.0 LPP 9 609C 14.40 Ea. 1.2 LPP 9 60914C.80 Ea. 1.5 LPP 60920C.00 Ea. 1.3 LPP 60922C 16.40 Ea. 1.6 LPP 60924C 17.70 Ea. 1.9 LPP 21 60926C 19.30 Ea. 2.2 LPP 24 60928C 21.25 Ea. 2.5 LPP 60930C 17.10 Ea. 1.6 LPP 60932C.60 Ea. 1.9 LPP 60934C 20. Ea. 2.3 LPP 21 60936C 22.10 Ea. 2.6 LPP 24 60938C 24.10 Ea. 3.0 LPP 60940C 19.75 Ea. 1.9 LPP 60942C 21.35 Ea. 2.3 LPP 60944C 23.10 Ea. 2.7 LPP 21 60946C 25.10 Ea. 3.1 LPP 24 60948C 27.30 Ea. 3.5 LPP 24 60962C 24.20 Ea. 3.0 LPP 24 60964C 26.35 Ea. 3.5 LPP 24 21 60966C 28.75 Ea. 4.0 LPP 24 24 60968C 31.25 Ea. 4.6 LPP Tops & Bottoms, 16 Ga. (Flat Top) Also used to separate compartments on 2 & 3 tier lockers mfg. since 1995. 9 605210C 13.90 Ea. 2.2 LPP 9 605211C.20 Ea. 2.5 LPP 9 6052C 17.30 Ea. 2.8 LPP 605220C.95 Ea. 2.5 LPP 605221C 17.30 Ea. 3.9 LPP 605222C 19.70 Ea. 4.3 LPP 21 605223C 21.50 Ea. 4.7 LPP 24 605224C 23.40 Ea. 5.2 LPP 605230C 17.90 Ea. 3.9 LPP 605231C 19.55 Ea. 4.4 LPP 605232C 21.30 Ea. 4.8 LPP 21 605233C 23.20 Ea. 5.2 LPP 24 605234C 25.40 Ea. 7.2 LPP 605240C 20.50 Ea. 4.6 LPP 605241C 22.30 Ea. 5.4 LPP 605242C 24.25 Ea. 6.4 LPP 21 605243C 26.40 Ea. 7.0 LPP 24 605244C 28.85 Ea. 7.5 LPP 24 605261C 56.90 Ea. 7.1 LPP 24 605262C 57.00 Ea. 7.5 LPP 24 21 605263C 57.25 Ea. 9.3 LPP 24 24 605264C 59.00 Ea. 10.0 LPP Basket Rack Units Order baskets separately. Number plates for rack are included - sequence must be specified. See page 3 for more details on number plates. For 9" Wide Baskets (4w x 7h = 28) 40 13 70 65910 506.60 Ea. 113.0 LPP For 9" Wide Baskets (4w x 8h = 32) 40 13 79 65930 565.85 Ea. 9.0 LPP For " Wide Baskets (3w x 7h = 21) 40 13 70 65800 479.00 Ea. 110.0 LPP For " Wide Baskets (3w x 8h = 24) 40 13 79 65830 534.70 Ea. 3.0 LPP Caster Set for Basket Racks, 3" Dia. For attachment to legs of basket racks. Priced as set of 4 swivel type casters. For double-faced racks, use 1 set of 4. Adds 5-1/2" to height of rack. Ordering 4 "Caster Supports" #65840C separately is required. 3 9650H 139.80 Set 5.0 4 Caster Support Order 4 per set of casters. 65840C 9.35 Ea. 2.0 LPP Baskets All baskets shipped F.O.B. Shiner, TX 77984. Note: Minimum order quantity is 5 each per size. Basket, Perforated Front Specify number plate sequence. 9 13 8 9646 53.55 Ea. 2.0 28 13 8 9641 57.05 Ea. 3.0 21 Basket with Pilfer Guard Specify number plate sequence. 9 13 8 9642 59.50 Ea. 3.0 28 13 8 9643 64.40 Ea. 3.0 21 Basket, All Wire Specify number plate sequence. 9 13 8 9621 52.45 Ea. 2.0 33 13 8 9620 55.25 Ea. 2.0 30 Basket Rack Parts Divider 65805C 7.20 Ea. 0.4 LPP Post 70" 70 65807C 25.10 Ea. 4.7 LPP Post 79" 79 65808C 28.40 Ea. 5.3 LPP End Brace 65819C 11. Pr. 1.1 LPP Shelf 65862C 46.20 Ea. 8.2 LPP Back Brace 049S 13.25 Pr. 2.5 LPP Basket Rack Padlock Staple 60833Z 2.90 Ea. 0.2 LPP For pricing & availability of Tuff Stuff Plastic locker bottoms and shelves, contact a Penco Representative. 58 Penco Products Inc.

Welded Locker Order Information Form For All-Welded & Angle Iron Lockers Sheet of Customer Name: Phone: FAX: Job Name: Quote No. Prepared By: Date: SPI Number if Applicable: How to Use this Form 1. Attach a floor plan of the room where the welded lockers are to go, showing the tiers in each frame (number of tiers - i.e. 2 Tier, 6 Tier, etc.) such as the example shown here: 2T 6T 2T 6T 2T 6T 2 Tier: x x 36 6 Tier: x x Drawings may be attached, or draw below on this form if there is sufficient space. Indicate the Width, Depth and Height of all the lockers on the drawings (check the Penco product literature for available sizes, or contact a Penco representative). 2. Complete the checklist of Options & Accessories at right. 3. Attach the Information Sheet and floor plan to the order. Note: Penco retains the right to determine Welded locker group widths. Maximum group width is usually 54". If site conditions restrict maximum group width, please advise. Floor Plan Below Attached Options & Accessories (Check Where Applicable) Base/Legs: No Base or Legs 4" High Legs (All-Welded Only) 4" High Channel Base Ventilation: Doors: Diamond-shaped Perforations Louvers Solid doors Sides: Diamond-Shaped Perforations Solid Row Ends: Diamond-Shaped Perforations Solid Slope Hoods Required? Color: (See Color Chart) Other Options Penco Products Inc. 59

Starter and Adder Method of Locker Pricing (For locker groups of 4-wide or greater.) Pricing of Starters and Adders is for those jobs that can be assembled in larger groupings. A Starter is defined as a complete 1-wide unit, while an Adder is a 1-wide unit minus a division, and supplied with only 1 rear leg (for lockers with legs). This system of pricing should be used when competing on large KD locker jobs for single row bulk packed Vanguard and Guardian style lockers. Please note: this pricing does NOT apply to Unit Packed lockers, QuickShip lockers, warehouse or factory assembled lockers or specially priced (SPI) lockers. (It also does not apply to Invincible II lockers, which are ordered by Basic Units and End Kits.) The table below provides price and weight adjustments to use when pricing Starters and Adders using bulk pack Vanguard or Guardian prices and weights as the base. Size STARTERS ADDERS D X H ADD to List Price ADD to Wt. DEDUCT from List Price DEDUCT from Wt. x36.5 $ 6.95 2.0 Lbs. -$ 3.55-1.0 Lbs. x36.5 $ 8.35 2.4 -$ 4.30-1.2 x36.5 $ 9.85 2.8 -$ 5.05-1.4 x48.5 $ 8.05 2.4 -$ 4.05-1.2 x48.5 $ 9.65 2.9 -$ 4.90-1.5 x48.5 $11.35 3.4 -$ 5.80-1.7 x60 $ 9.35 2.8 -$ 4.70-1.4 x60 $ 11.20 3.4 -$ 5.60-1.7 x60 $ 13.55 3.9 -$ 6.80-1.9 21x60 $ 16.75 5.6 -$ 8.40-2.8 24x60 $.40 6.4 -$ 9.20-3.2 x72 $ 10.95 3.3 -$ 5.45-1.7 x72 $.65 4.1 -$ 6.30-2.0 x72 $.70 4.7 -$ 7.85-2.3 21x72 $.95 6.5 -$ 9.45-3.2 24x72 $ 20.95 7.7 -$ 10.45-3.9 x84 $ 16.70 4.4 -$ 8.35-2.2 x84 $.40 4.7 -$ 9.20-2.4 x84 $ 23.70 5.5 -$ 11.80-2.7 The default for our KD locker catalog numbers continues to be 3-wide groupings unless Starter & Adder units are specified. The quantity of Starter & Adder units must be clearly indicated so that the order can processed accurately. Penco ProQuote - How to utilize Penco ProQuote software with manual entries for Starters/Adders. 1) Enter the quantity and the normal catalog number for Vanguard or Guardian bulk pack lockers. 2) In the next row, enter the quantity of the Starter units. Type STARTER in the Cat.No. field. Complete the description field to make it clear that Starter charges for Cat.No. xxxxx are being entered. Type the additional price and additional weight in the respective fields. ProQuote will extend the dollars and additional weight. 3) In the next row, enter the quantity of the Adder units. Type ADDER in the Cat.No. field. Complete the description field to make it clear that Adder charges for Cat.No. xxxxx are being entered. Type the price and weight DEDUCTIONS in the respective fields and be sure to enter a MINUS SIGN before the list price and weight deducts. ProQuote will do the math. 4) Check to see that the sum of Starters plus Adders equals the total number of locker frames to be priced in this manner. 60 Penco Products Inc.

ADA Locker Guidelines and Locker Care ADA Locker Guidelines The Americans with Disabilities Act has several requirements that apply to lockers. Penco lockers that are best suited to meeting ADA requirements are: Single tier 60" or 72" high with recessed handle and 3 point latch with the shelf placed no higher than 48" from the floor (we recommend FIELD DRILLING for required shelf location). Double tier 36" with recessed handle and 2 point latch. Assign lower tier only to disabled. In both cases, an additional shelf may be required at " (from the finished floor. (We recommend field drilling for required shelf location). Though Classic III recessed handles are favored, a properly adjusted Defiant II, cremone style or box locker door pull handle can meet the literal criteria by taking less than 5 lbs. of force to actuate and not requiring pinching, twisting or tight grasping. Other Requirements: The owner or architect may require a handicap sign to be placed on the door (handicap decal part # 8690). In addition, the architect should show the location of the handicap lockers on the drawings and provide the necessary clear open space in front of the selected lockers. It is important to note that standard 9-1/2 inch deep locker room benches do not meet the current accessibility requirements. In addition to a larger seating surface (20-24 deep) back support is also required, either by placing the bench at a wall, or attaching specifically sized backs. For the most up to date information about barrier free requirements of all types, consult the Americans with Disabilities Act section of the U.S. Department of Justice web site. (www. ada.gov) Locker Care The following information is offered for use in providing information on locker care and maintenance for customers. ANCHORING: For safety, be certain that lockers are anchored to the wall and floor before putting them into use. This will prevent the lockers from tipping. FINISH: To preserve the finish of the lockers, they must be kept dry and free from contaminants. To clean the lockers, use a clean damp cloth (with a mild soap solution, if required). Wipe thoroughly dry immediately after cleaning. Avoid the use of harsh detergents, abrasive cleaners, germicidal cleaners and acids which can damage the finish and void the guarantee. Note that some cleaners come as concentrates and must be diluted before use! VENTILATION: The area where the lockers are installed must be well ventilated to reduce humidity, especially in rooms associated with swimming pools. Airborne corrosives such as chlorine fumes are extremely detrimental to the finish on lockers and steel bench pedestals. INSPECTION: Periodic inspection of all lockers should be made to determine if any lockers have inoperable locks, or broken, missing or loose parts. Anchoring must be reconfirmed to be certain that it remains firm. 1 Tier 60" or 72" high ADA Lockers with recessed handle and 3 Point Latch. 2 Tier 30" high ADA Lockers with recessed handle and 2 Point Latch. Penco Products Inc. 61

Shelf, "TAB*", Partition & Lower Tier Head Location and Usage / Metric Conversion Flat Top (T.A.B.) or Slope Top Intermediate Shelf Spacing Single tier lockers have a shelf approx. 9 below the top of the locker. For Multi-tier lockers take the height of the locker and divide the number of doors to get nominal shelf spacing. Example: Height 72, Number of Doors 6, 72 /6 = distance between shelves. Locker doors and frame can also be used as a template for shelf or flat top (T.A.B.) positioning. Shelf Bottom (T.A.B.) Flat Top (T.A.B.) Bottom (T.A.B.) Shelf 1 Tier 2 Top and Bottom (T.A.B.) 1 Intermediate Shelf 2 Tier 3 Top and Bottom (T.A.B.) 3 Tier 4 Top and Bottom (T.A.B.) Box Over 2 Top and Bottom (T.A.B.) 1 Intermediate Shelf Flat Top (T.A.B.) or Slope Top Flat Top (T.A.B.) or Slope Top 1 Half Shelf on each side of partition Shelf Lower Tier Head Shelf Shelf Shelf Shelf Partition Partition Shelf Bottom (T.A.B.) Bottom (T.A.B.) Bottom (T.A.B.) Bottom (T.A.B.) Bottom (T.A.B.) 4 Tier 2 Top and Bottom (T.A.B.) 3 Intermediate Shelf 5 Tier 2 Top and Bottom (T.A.B.) 4 Intermediate Shelf 6 Tier 2 Top and Bottom (T.A.B.) 5 Intermediate Shelf Duplex 2 Top and Bottom (T.A.B.) 2 Half Shelves 1 Partition DX 2 Person 2 Top and Bottom (T.A.B.) 1 Lower Tier Head 1 Intermediate Shelf 1 Partition 2P Dual 1 Shelves 2 Top and Bottom (T.A.B.) 1 Partition 2D 7 Person 4 Top and Bottom (T.A.B.) 6 Intermediate Shelf The hole punching pattern on Divisions are the same for all lockers except for 5 Tier Lockers and 16 gauge Exposed End Panels. Locker Tops, Bottom (T.A.B.) and Shelves Flat Top Slope Top 2 Person, Dual and Duplex Parts Flat Tops (same part as bottoms) Slope Top Lower Tier Head Shelf Partition * Tops and Bottoms are often called TAB's. (Top And Bottom) Bottom (Same part as flat top) 62 Penco Products Inc.