Installation Instructions - PDF Free Download

CR0A00 - CR9A00, CR264A00 - CR269A00, CR288A00 - CR296A00 CRSINGLE037A00 - CRSINGLE054A00 SMALL ROOFTOP UNITS ACCESSORY ELECTRIC AND SINGLE POINT BOX ELECTRIC COOLING AND HEAT PUMP 3to2---/2TONS Installation Instructions TABLE OF CONTENTS SAFETY CONSIDERATIONS... PACKAGE CONTENTS... 2 PACKAGE USAGE... 4 GENERAL... 5 GENERAL INSTALLATION SEQUENCE... 8 All Units Except HP - Size 4... 8 Installing Single Point Box (CRSINGLE037A00-054A00)... 8 Installing Electric Heater (CR0A00-9A00, CR264A00-269A00)... 0 Heat Pump Size 4 Only... 4 Installing Single Point Box (CRSINGLE047A00, 050A00-054A00... 4 Installing Electric Heater (CR288A00-296A00)... 6 APPENDIX A... 23 APPENDIX B... 30 APPENDIX C... 43 IMPORTANT: Read these instructions completely before attempting to install this accessory. SAFETY CONSIDERATIONS Installation and servicing of air-conditioning equipment can be hazardous due to system pressure and electrical components. Only trained and qualified service personnel should install, repair, or service air-conditioning equipment. Untrained personnel can perform the basic maintenance functions. All other operations should be performed by trained service personnel. When working on air-conditioning equipment, observe precautions in the literature, tags and labels attached to the unit, and other safety precautions that may apply. Follow all safety codes. Wear safety glasses and work gloves. Recognize safety information. This is the safety-alert symbol. When you see this symbol on the unit and in instructions or manuals, be alert to the potential for personal injury. Understand the signal words DANGER, WARNING, and CAUTION. These words are used with the safety-alert symbol. DANGER identifies the most serious hazards which will result in severe personal injury or death. WARNING signifies a hazard which could result in personal injury or death. CAUTION is used to identify unsafe practices which may result in minor personal injury or product and property damage. NOTE is used to highlight suggestions which will result in enhanced installation, reliability, or operation.! WARNING ELECTRICAL SHOCK HAZARD Failure to follow this warning could result in personal injury or death. Turn off all power to unit and install lockout tag. Power can come to unit from from multiple sources. Verify power is off with a meter or probe.! CAUTION CUT HAZARD Failure to follow this caution may result in personal injury. Sheet metal parts may have sharp edges or burrs. Use care and wear appropriate protective clothing, safety glasses and gloves when handling parts and servicing units. Copyright 200 CAC / BDP D 730 W. Morris St. D Indianapolis, IN 4623 Printed in U.S.A. Edition Date: 05/0 Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations. Catalog No:IIK---CRHTRSIN0---03 Replaces: IIK ---CRHTRSIN0 ---02

PACKAGE USAGE CARRIER MODELS MODEL NUMBER CHASSIS GROUP UNIT SIZES 50HC AC --- 2 04---2 50HCQ HP --- 2 04---09 50TC AC --- 04---4 50TCQ HP --- 04---4 BRYANT MODELS MODEL NUMBER CHASSIS GROUP UNIT SIZES 548J HP --- 04---4 549J HP --- 2 04---09 55J AC --- 2 04---2 558J AC --- 04---4 * AC: Cooling Only (air conditioner) HP: Heat pump PACKAGE CONTENTS- ELECTRIC S CR0A00-9A00, CR264A00-269A00 QTY CONTENTS Heater module Heater slider track 4 Screws Wiring label Red wire (0 gauge)* Splice connector* Wire tie* * Supplied with electric heater packages CR0A00, CR02A00, CR03B00, and CR04B00 only. PACKAGE CONTENTS- ELECTRIC S CR288A00-296A00 QTY CONTENTS Heater module Heater slide track 4 Screws Wiring label Warning label CRSINGLE038A00 ITEM DESCRIPTION QUANTITY Single Point Box Housing Assembly (Height 8 --- in/449 mm) Terminal block/fuse holder Fuse block Fuses, 60--- A class RK5 6 Power distribution harness, Tap, #0 3 Rain shield with conduit seal Screws, #0 x ½ --- in 2 Wire ties 7 Tube clamp CRSINGLE039A00 ITEM DESCRIPTION QUANTITY Single Point Box Housing Assembly (Height 8 --- in/449 mm) Terminal block/fuse holder Fuse block 2 Fuses, 60--- A class RK5 9 Power distribution harness, Tap, #0 3 Rain shield with conduit seal Screws, #0 x ½ --- in 2 Wire ties 7 Tube clamp CRSINGLE040A00 ITEM DESCRIPTION QUANTITY Single Point Box Housing Assembly (Height 8 --- in/449 mm) Terminal block/fuse holder Fuse block Fuses, 60--- A class RK5 4 Power distribution harness, Tap, #0 2 Rain shield with conduit seal Screws, #0 x ½ --- in 2 Wire ties 7 Tube clamp PACKAGE CONTENTS- CRSINGLE037A00 ITEM DESCRIPTION QUANTITY Single Point Box Housing Assembly (Height 8 --- in/449 mm) Terminal block, Tap, #0 3 Rain shield with conduit seal Screws, #0 x ½ --- in 2 Wire ties 7 Tube clamp 2

CRSINGLE04A00 ITEM DESCRIPTION QUANTITY Single Point Box Housing Assembly (Height 8 --- in/449 mm) Terminal block/fuse holder Fuse block Fuses, 60--- A class RK5 6 Power distribution harness, Tap, #0 2 Rain shield with conduit seal Screws, #0 x ½ --- in 2 Wire ties 7 Tube clamp CRSINGLE042A00 ITEM DESCRIPTION QUANTITY Single Point Box Housing Assembly (Height 25 --- in/639 mm) Terminal block, Tap, #0 3 Rain shield with conduit seal Screws, #0 x ½ --- in 8 Wire ties 7 CRSINGLE043A00 ITEM DESCRIPTION QUANTITY Single Point Box Housing Assembly (Height 25 --- in/639 mm) Terminal block/fuse holder Fuse block Terminal block (TB --- 0) 2 Fuses, 60--- A class RK5 6 Power distribution harness, Tap, #0 6 Screws, #8 x ½ --- in 2 Rain shield with conduit seal Screws, #0 x ½ --- in 8 Wire ties 7 CRSINGLE044A00 ITEM DESCRIPTION QUANTITY Single Point Box Housing Assembly (Height 25 --- in/639 mm) Terminal block Fuse block 2 Fuses, 60--- A class T (600v) 6 Power distribution harness, Tap, #0 3 Rain shield with conduit seal Screws, #0 x ½ --- in 8 Wire ties 7 CRSINGLE045A00 ITEM DESCRIPTION QUANTITY Single Point Box Housing Assembly (Height 25 --- in/639 mm) Terminal block/fuse holder Fuse block 2 Fuses, 60--- A class RK5 9 Power distribution harness, Tap, #0 6 Terminal block (TB0) 2 Screws, #8 x ½ --- in 2 Rain shield with conduit seal Screws, #0 x ½ --- in 8 Wire ties 7 CRSINGLE046A00 ITEM DESCRIPTION QUANTITY Single Point Box Housing Assembly (Height 25 --- in/639 mm) Terminal block/fuse holder Fuse block 3 Fuses, 60--- A class RK5 2 Power distribution harness, Tap, #0 3 Rain shield with conduit seal Screws, #0 x ½ --- in 8 Wire ties 7 CRSINGLE047A00 ITEM DESCRIPTION QUANTITY Single Point Box Housing Assembly (Height 33 --- in/845 mm) Terminal block, Tap, #0 3 Rain shield, small Rain shield with conduit seal Screws, #0 x ½ --- in 8 Wire ties 7 CRSINGLE048A00 ITEM DESCRIPTION QUANTITY Single Point Box Housing Assembly (Height 25 --- in/639 mm) Terminal block Fuse block 3 Fuses, 60--- A class RK5 9 Power distribution harness, Tap, #0 3 Rain shield with conduit seal Screws, #0 x ½ --- in 8 Wire ties 7 3

CRSINGLE049A00 ITEM DESCRIPTION QUANTITY Single Point Box Housing Assembly (Height 33 --- in/845 mm) Terminal block/fuse holder Fuse block Fuses, 60--- A class RK5 6 Power distribution harness, Tap, #0 6 Terminal block (TB0) 2 Screws, #8 x ½ --- in 2 Rain shield, small Rain shield with conduit seal Screws, #0 x ½ --- in 8 Wire ties 7 CRSINGLE050A00 ITEM DESCRIPTION QUANTITY Single Point Box Housing Assembly (Height 33 --- in/845 mm) Terminal block Fuse block 2 Fuses, 60--- A class T (600v) 6 Power distribution harness, Tap, #0 3 Rain shield, small Rain shield with conduit seal Screws, #0 x ½ --- in 8 Wire ties 7 CRSINGLE05A00 ITEM DESCRIPTION QUANTITY Single Point Box Housing Assembly (Height 33 --- in/845 mm) Terminal block/fuse holder Fuse block 2 Fuses, 60--- A class RK5 9 Power distribution harness, Tap, #0 6 Terminal block (TB0) 2 Screws, #8 x ½ --- in 2 Rain shield, small Rain shield with conduit seal Screws, #0 x ½ --- in 8 Wire ties 7 CRSINGLE052A00 ITEM DESCRIPTION QUANTITY Single Point Box Housing Assembly (Height 33 --- in/845 mm) Terminal block Fuse block 3 Fuses, 60--- A class T (600v) 9 Power distribution harness, Tap, #0 3 Rain shield, small Rain shield with conduit seal Screws, #0 x ½ --- in 8 Wire ties 7 CRSINGLE053A00 ITEM DESCRIPTION QUANTITY Single Point Box Housing Assembly (Height 33 --- in/845 mm) Terminal block Fuse block 4 Fuses, 60--- A class RK5 2 Power distribution harness, Tap, #0 6 Terminal block (TB0) 2 Screws, #8 x ½ --- in 2 Rain shield, small Rain shield with conduit seal Screws, #0 x ½ --- in 8 Wire ties 7 CRSINGLE054A00 ITEM DESCRIPTION QUANTITY Single Point Box Housing Assembly (Height 33 --- in/845 mm) Terminal block Fuse block 5 Fuses, 60--- A class RK5 5 Power distribution harness, Tap, #0 6 Terminal block (TB0) 2 Screws, #8 x ½ --- in 2 Rain shield, small Rain shield with conduit seal Screws, #0 x ½ --- in 8 Wire ties 7 4

GENERAL PuronR Units This installation instruction manual describes the installation of electric heaters and associated fuse block/field power termination kits (single point box or SPB) on small rooftop units in nominal cooling capacities from 3 to 2.5 tons (unit sizes 04 through 4). These rooftop units use Puron refrigerant (R-40A). See Package Usage tables on page 2 for applicable unit models. Unit types include cooling units (AC) and heat pumps (HP) distributed over several chassis sizes. Unit AC-, AC-2, HP-, HP-2 are identified. This information does not include selection data. Refer to project plans, job submittals and selection programs for heater and field power termination/spb kit usage. Some electric heaters used on these Puron (R-40A) units may also be installed in earlier R-22 rooftop units. Refer to Form 50-8SI or IIK-548-36-49 for installation instructions on heater packages CR0A00 through 9A00 with earlier models. distributor office for a copy of this form. Electric Heaters Contact your local Heaters are shipped with one heater per carton. The carton is marked with a Sales Package Number. On all heaters except CR0A00 through 9A00, the heater Model Number (as marked on the heater infoplate) is the same as the Sales Package number. On CR0A00 through 9A00 heaters, the value in position 9 of the part number differs between the sales package part number (value is ) and bare heater model number (value is 0). (See Table.) The heaters are modular in design, with heater frames holding open coil resistance wires strung through ceramic insulators, limit switches and one or two control contactors. Power conductors are attached. One or two heater modules may be used in a unit. Heater modules are installed in the compartment below the indoor (supply) fan outlet. Access is through the indoor access panel. Heater modules slide into the compartment on tracks along the bottom of the heater opening. (See Fig. and 2.) Not all available heater modules may be used in every unit. Use only those heater modules that are UL listed for use in a specific size unit. Refer to the label on the unit cabinet for the list of approved heaters. (See Fig. and 2.) See Appendix C for electric heater module data. Single Point Boxes and Fuses The Single Point Box kits provide a field power termination location plus an enclosure for heater fuses when required by code. The SPBs are installed under the unit s main control box and include a hinged cover plus all internal wiring. Minimum components of the SPB are a field power terminal block with tap conductors (to connect to the unit s main control box field terminals). Maximum component population includes up to five fuse blocks. Fuses for electric heater circuits are required and provided when the unit s MOCP exceeds 60-A or when the total heater Full Load Amp value exceeds 48-A. When fuses are required and provided, the cooling circuit is also provided with fuse protection; some units require minor wiring changes in the main control box (see section on TB0 terminal blocks). No Fuses If the unit s MOCP device rating is 60-A or less, then the MOCP device is recognized as providing the required overcurrent protection to the heater and no internal fusing is required. If two heater modules are installed, a single point box that contains only a field power terminal block is required. If only one heater module is installed, no fuse or single point box is required. Connect field power leads and heater power leads to the unit s field connection terminals in the main control box. See tables at the beginning of Appendix A and B for where-used information on the single point boxes and for connections Figure number. 5

Table Heater Model Number Bare Heater Model Number Heater Sales Package PNO Includes: Bare Heater Carton and packing materials Installation sheet C R H E A T E R 0 0 A 0 0 C R H E A T E R 0 A 0 0 Carrier Corporation MODEL 730 West Morris Street Indianapolis, IN 4623 U.S.A. QTY VOLTS AC PH HZ RLA LRA REF. SYSTEM R40A TEST PRESSURE GAGE COMPR A 208/230 3 60 5.6 0 0.7 LBS 4.9 kg HI 650 PSI 4482 COMPR B LBS kg LO 450 PSI 303 COMPR C LBS kg FAN MTR QTY VOLTS AC PH HZ FLA OUTDOOR 208/230 60.5 INDOOR 208/230 3 60 5.2 PWR.EXH. CHARGE SYSTEM PER INSTALLATION INSTRUCTIONS ELC.HEAT SUITABLE FOR OUTDOOR INSTALLATION OTHER POWER MIN. CKT. MAX FUSE OR HACR SUPPLY 208/230 VOLT 3 PH 60 HZ AMPS BREAKER PER NEC MAX OVERCURRENT 253 MAX 87 MIN 26.2 PROTECTION DEVICE 40 - PERMISSIBLE VOLTAGE AT UNIT DOWN SUPPLY SIDE SUPPLY 50TC-A06A2A5A0A0A0 kpa kpa MINIMUM UNIT DISCONNECT FLA LRA 26 44 25 MIN CLEARANCE TO COMBUSTIBLE MATERIALS INCHES mm. FOR FIRST INCHES mm. 2 305 OF DUCT WHEN ELECTRIC IS INSTALLED MIN CLEARANCE TO COMBUSTIBLE MATERIALS INCHES mm. 25 FOR FIRST INCHES mm. 2 305 OF DUCT WHEN ELECTRIC IS INSTALLED *FOR INSTALLATION ON COMBUSTIBLE FLOORING OR CLASS A,B, OR C ROOFING MATERIAL ACCESSORY MODEL NUMBER 02A 208/ HERE VOLTS PH HZ FLA CHECK 3 60 3.6/ 5.6 MIN CKT AMPS 26.2/ 26.2 FUSE OR HACR BREAKER PER NEC MAXIMUM OVERCURRENT PROTECTION DEVICE SINGLE PT. BOX MODEL NUMBER MINIMUM UNIT DISCONNECT FLA LRA 40/40 -/- - 26/26 44/ 44 04B 208/ 05A 208/ 04B+04B 208/ 04B+05A 208/ 3 60 2.9/ 25.3 3 60 33.4/ 38.5 3 60 43.8/ 50.5 3 60 55.2/ 63.8 33.9/ 38. 48.3/ 54.6 6.3/ 69.6 75.5/ 86.3 40/40 -/- - 3/35 44/ 44 50/60 -/- 037 44/50 44/ 44 70/70 -/- 038 56/64 44/ 44 80/90 -/- 038 69/79 44/ 44 INSTALLER NOTE:.INSTALL ACCESS PER INSTALL INSTR ENCLOSED WITH. MARK SPACE "CHECK HERE" FOR MODEL USED USE MIN CKT AMPS & MAX OVER- CURRENT DEVICE AMPS LISTED FOR. IF NO IS USED MARK SPACE "CHECK HERE" FOR NONE. 2.S ARE MANUFACTURED BY EMERSON HEATING PRODUCTS OR TUTCO ELECTRIC. COOLING HP HEATING CAPACITY Btu/Hr CAPACITY kw EER COP 59000 7.2 3 THIS EQUIPMENT COMPLIES WITH THE 2004 REQUIREMENTS OF ASHRAE 90. Fig. - Unit Informative Data Label C053 6

MODEL 50TC-A06A2A5A0A0A0 REFRIGERANT CHARGE R40A ELECTRICAL DATA FOR ACCESSORY POWER EXHAUST ONLY ACCESSORY POWER EXHAUST MODEL NUMBER CRPWREXH_ ACCESSORY MODEL NUMBER 02A SINGLE PT BOX MODEL - NUMBER 04B SINGLE PT BOX MODEL - NUMBER 05A SINGLE PT BOX MODEL 037 NUMBER 04B+04B SINGLE PT BOX MODEL 038 NUMBER 04B+05A SINGLE PT BOX MODEL 038 NUMBER CHECK HERE POWER VOLTS PH HZ EXHAUST MIN CKT FLA AMPS ELECTRICAL DATA FOR ACCESSORY POWER EXHAUST INSTALLED IN COMBINATAION WITH ELECTRIC CHECK VOLTS PH HZ MIN CKT HERE FLA AMPS 208/ 208/ 208/ 208/ 208/ 3 60 3.6/ 5.6 3 60 2.9/ 25.3 3 60 33.4/ 38.5 3 60 43.8/ 50.5 3 60 55.2/ 63.8 28./28.4 36.3/40.5 50.6/57.0 63.6/72.0 77.9/88.6 28. FUSE OR HACR BREAKER PER NEC 40/40 40/45 60/60 70/80 80/90 FUSE OR HACR BREAKER PER NEC 40 -/- MAXIMUM OVERCURRENT POROTECTION DEVICE MAXIMUM OVERCURRENT POROTECTION DEVICE -/- -/- -/- -/- -/- MINIMUM UNIT DISCONNECT FLA 28 LRA 46 MINIMUM UNIT DISCONNECT FLA 28/28 LRA 46/46 FLA 33/37 LRA 46/46 FLA 47/52 LRA 46/46 FLA 59/66 LRA 46/46 FLA 72/82 LRA 46/46 FLA SINGLE PT BOX MODEL NUMBER INSTALLER NOTE:.INSTALL ACCESS. AND/OR POWER EXHAUST PER INSTALL INSTR ENCLOSED WITH AND POWER EXHAUST. MARKSPACE "CHECK HERE" FOR MODEL USED. USE MIN CKT AMPS AND MAX OVER CURRENT DEVICE AMPS LISTED FOR AND POWER EXHAUST. 2.S ARE MANUFACTURED BY EMERSON HEATING PRODUCTS OR TUTCO ELECTRIC. LRA *50TC-A06A2A5A0A0A0* Fig. 2 - Unit Informative Data Label, Power Exhaust Installed C0532 7

TB0 On larger 208/230-3-60 units, the MOCP rating for the base cooling circuit exceeds 60-A. On these applications, the single point box kit contains two small single-pole terminal blocks that are installed in the main control box. Minor relocation of wiring results in separating the indoor fan motor load from the main power circuit, allowing this load to be protected with a second fuse set. See single point box kits CRSINGLE043A00, 045A00, 049A00, 05A00, 053A00 and 054A00. (Units AC- size 4 and HP- size 2 use only one TB0 block to separate Compressor 2 and outdoor fan motor loads from main unit circuit). Single Point Box Contents See Package Content tables for a list of components included in each single point box kit. Note the height differences and their use in specific size units. Control Wiring Heater modules contain one or two heater control contactors. If two heater modules are installed, or a two-circuit heater module is installed, the cooling unit (AC type) can be connected for one-stage or two-stage heating control. On all heat pump units (HP type), all heater contactors will be connected to provide second-stage heating control. GENERAL INSTALLATION SEQUENCE. Pre-stage heater packages and single point boxes by placing the required component cartons at each unit. 2. Check the heater sales package number and single point box part number (if used) against the part numbers on the unit s infoplate. See Fig. and 2 for typical data. 3. Install the SPB and connect power wiring tap conductors to field power terminals in main control box. 4. Install the electric heater module(s) and connect heater power conductors to single point box or main unit control box per appropriate connections figure. (See Appendix A and B.) 5. Connect the heater control contactors to unit terminal block TB4. 6. Mark the unit infoplate to indicate which heater module(s) have been installed. 7. Note the required wire size ampacity (WSA) for the field power supply conductors. Select and install suitable field power conductors from external safety disconnect to unit power connection points, or confirm wiring already provided is suitable for required WSA. All Units Except HP - Size 4 The following text covers installation of single point boxes and electric heaters in all units EXCEPT the HP- size 4 (2.5 ton) heat pump. For instructions on the HP- size 4 heat pump, skip to page 4. Check sales packages Following the project drawing schedule tables or submittal documents, select the scheduled heaters and single point boxes (if used) and place at each unit. Compare the sales package number(s) for scheduled heater modules against the approved usage table on the unit s infoplate. See Fig. and 2 for typical plate data. If the scheduled heater usage does not appear on the unit infoplate label, STOP. Contact the project engineer or the local distributor sales office for clarification. Open the cartons and inspect for damage. Installing Single Point Box (CRSINGLE037A00-054A00). If power is already connected to unit, disconnect all power to the unit per correct lock-out tag-out procedures. 2. Remove indoor and outdoor access panel. (See Fig. 3 and 4.) Save panel and screws. DISCONNECT MOUNTING LOCATION UNIT BLOCK-OFF PANEL OUTDOOR ACCESS PANEL INDOOR ACCESS PANEL Fig. 3 - Typical Access Panel Location (AC-/HP-3to6Ton,AC-2/HP-23to5Ton) DISCONNECT MOUNTING LOCATION UNIT BLOCK-OFF PANEL OUTDOOR ACCESS PANEL INDOOR ACCESS PANEL Fig. 4 - Typical Access Panel Location (AC - 7 / 2 to 2 / 2 Ton,AC-26to8 / 2 Ton, HP - 7 / 2 to 0 Ton ) C0833 C0846 8

3 2 23 ALLIED PA CORP. MODEL NO. ERIAL NO. 3 2 23 OD 22.2 ISTED AIR NDITIONING UIP ACCESS P / N 2-560-4 REV 346N. 23 3 DISCONNECT MOUNTING LOCA TION EM T OR RIGID CONDUIT (FIELD-SUPPLIED) SINGLE POINT BO X (NOT SHIPPED CENTER WITH UNIT) POST MANUAL RESET LIMIT SWITCH HEA TER COVERS CONTROL BOX BUSHING SINGLE POINT BOX MOUNTING SCREWS DRIP BOOT BRACKET MOUNTING SCREWS POWER WIRES MAIN SINGLE POINT BRACKET AND BO X HEA TER HEA TER HEA TER CONTROL CONDUIT MOUNTING MODULE MODULE MOUNTING BO X DRIP BOOT SCREW (LOCA TION ) (LOCA TION 2) BRACKET CONTRO L WIRE TERMINAL BLOCK Fig. 5 - Typical Component Location (Size 04-06 Shown) C0845 3. Remove control box cover and center post. Save screws.(seefig.5.) 4. If unit does not have the factory-installed disconnect option or has not had field power wiring connected,skiptostep5. When unit is equipped with factory-installed disconnect or has field power wiring connected, disconnect the power leads at the control box terminals and withdraw the conductors from the control box. 5. All bushings in the area of the control box where the single point box (SPB) mounts, must be removed prior to securing the SPB to the control box. (See Fig. 7.) Also, for units installed in the snow belt, all unplugged holes in the bottom of the control box which are not used must be plugged before installing the SPB. Use foil tape or reinstall the bushings from the outside of the control box prior to securing the SPB. (See Fig. 8.) 6. Remove the single point box cover. Secure single point box to the underside of the control box with the 2 screws provided. (See Fig. 6.) Re -install bushing on the SPB tap conductors. (See Fig. 8.) 7. Secure the rainshield (conduit drip boot bracket) assembly to the back of the single point box with 2 of the screws provided. (See Fig. 6.) The channel portion of the bracket assembly extends to the top panel behind the control box. Secure all wires to bracket with field-supplied wire tie as shown. (See Fig. 0.) FOAM BUSHING RELAYS MOUNTING SCREWS Fig. 6 - Typical Single Point Kit Installation Fig. 7 - Control Box - Bushings to Remove C0836 C09005 C09006 Fig. 8 - Bushings Replaced from Outside Control Box 9

8. Connect power tap conductors to unit main control box. a. Single point boxes with two or three tap conductors-route the tap conductors (with bushing added per Step 5) into the unit main control box. Connect the power tap conductors to the designated terminals in the unit s control box for field power connections. Refer to the wiring diagram in the unit, to unit installation instructions for Field Power Wiring Connections or to Appendix AorB. b. Single point boxes with six tap conductors (CRSINGLE043A00, 045A00, 049A00, 05A00, 053A00 and 054A00) (.) All units EXCEPT AC- size 4 and HP- size 2 These single point boxes include two sets of three -lead power tap conductors connected to two separate fuse blocks. These kits also include two terminal blocks (TB0A and TB0B) and attachment screws. Mount these terminal blocks in the unit s control box next to compressor contactor C. (See Appendix A or B.) S Relocate these wires: At IFC terminal 3, disconnect Compressor and Compressor 2 ORN leads; reconnect at TB0A. At C terminal 3, disconnect ID Fan lead; reconnect at TB0B. At C terminal, disconnect jumper; reconnect to IFC terminal. S Route the first set of tap conductors (attached at upper fuse block, with bushing per Step 5) into the main control box; connect at: : C terminal : C terminal 3 (long lead with terminal): TB0A S Route the second set of tap conductors (attached at second fuse block) into the main control box; connect at: : IFC terminal (long lead with terminal): TB0B : IFC terminal 3 (2.)UnitsAC-size4andHP-Size2Only Mount one TB0 terminal block in the unit s control box between compressor contactors C and C2. (See Fig. 9.) S Relocate these wires: At IFC terminal 3, disconnect Compressor 2 ORN and OFM leads; reconnect at TB0. S S S Remove these leads: At C-, remove jumper to C2-. Discard. At C-3, remove jumper to C2-3. Discard. Route the first set of tap conductors (attached at upper fuse block, with bushing per Step 5) into the main control box; connect at: : C terminal : C terminal 3 : IFC terminal 3 Route the second set of tap conductors (attached at second fuse block) into the main control box; connect at: : C2 terminal : C2 terminal 3 : TB0 Installing Electric Heater (CR0A00-9A00, CR264A00-269A00). Remove heater cover(s) from heater mounting. bracket. Save screws. 2. Install heater slide bracket(s) from the heater kit through the bottom of the heater mounting hole(s) and fasten each with the two screws provided. (See Fig. 2.) NOTE: Modules CR05A00, CR 09A00, CR2A00, CR4A00, CR5A00, and CR9A00 are keyed andmustbeinstalledinlocationevenwhenusedaspart of a 2-module option. (See Fig. for AC- size 04 to 07, AC-2 size 04 to 06, HP- size 04 to 07, HP-2 size 04 to 06 units or Fig. 2 for AC- size 08 to 2, AC-2 size 07to09,HP-size08to2units.) NOTE: Modules CR265A00 through CR269A00 (480-v, used on AC-2 size 07 only) are keyed and must be installed in location 2. In addition, these modules are always used as a single module option. (See Fig. 3.) 3. To install module, engage flange on heater with track in unit and slide heater through mounting bracket opening. Fasten heater module to heater mounting bracket with the 4 screws saved from Step. (See Fig. 2.) 0

02A CIR# CIR#2 07A Fig. 9 - TB0 Locations and Connections C0598 BD236B N TRAN 3O BV2075 E 60 HZ 30-8703 30V OR 200V RD OV YL D 24V 75VA C COMM 4. Single-phase heater conversion 208/230-v heaters CR0A00 through 04B00 are factory-wired for 3-phase applications but can be converted to single -phase by changing one wire as described below. Three -phase applications: Skip to Step 5. For single -phase applications, rewire the heater as follows (Fig. 4 and Fig. 5): a. Connect 0-gauge red wire to splice connector. b. Remove yellow wire from heater contactor terminal and connect to splice connector. c. Using the wire tie provided, fasten red wire to heater power wire harness near existing wire tie on heater module. This provides strain relief for the red wire. CONDUIT CONDUIT DRIP BOOT Fig. 0 - Typical Conduit Installation WIRE TIE C0847

P / N 2-560-4 REV KEY FOR MODULE LOCATON LEGEND HR -- Heater Relay HTR -- Heater LS -- Limit Switch Fig. 4 - Single-Phase Heater Wiring C0849 Fig. - Typical Electric Heat Installation (AC - Sizes 04 to 07, AC -2 Sizes 04-06, HP - Sizes 04-07, HP -2 Sizes 04-06) C0900 RED WIRE POWER WIRE HARNESS 2 23 3 SLIDE TRACK SPLICE CONNECTOR MODEL NO. ERIAL NO. ISTED AIR NDITIONING UIP ACCESS 346N. 23 OD 3 22.2 FLANGE TRACK SCREWS KEY FOR MODULE LOCATION C0557 Fig. 2 - Typical Module Installation (AC - Sizes 08 to 2, AC -2 Sizes 07-09, HP - Sizes 08-2) Fig. 5 - Typical Single-Phase Wiring Installed C08420 5. Route power wires from heater module(s) through the foam bushing in the center partition and into the single point box. (See Fig. 4.) Connect to terminal block or fuse blocks per schematics in Appendix A or B. See Tables at beginning of each Appendix to identify the appropriate figure. All heaters are single bank heaters except CR0A00, 02A00, 268A00 and 269A00 which are dual bank heaters. These heaters will be wired as two heaters (i.e., 6 leads). Fusing is shown pictorially on the unit wiring schematic label. KEYWAY FOR MODULE LOCATION 2 Fig. 3 - Heater Bracket Keyway (AC-2, HP-2 Size 07 Units Only) C0558 If no single point box is required for the unit and heater combination, run the heater power supply wiring through the grommet holes to the main unit control box s field power connection points or to optional factory-supplied 80 amp disconnect. The optional factory-supplied disconnect has a maximum rating of 80 amps. Above 80 amps a field-supplied disconnect is required. 2

6. Factory control wiring for heaters runs from unit control box to terminal block TB-4, mounted in the heater compartment above module location. (See Fig. 6.) Connect the heater control wiring at TB-4. For AC- and AC-2 units, see Fig. 6. For HP- and HP-2 units, see Fig. 7. LCTB CONTL BOARD 2 VIO 2 23 3 ORN 3 2 MODEL NO. ERIAL NO. OD TB4 Field Connections ORN VIO 2 3 VIO VIO Elec Htr VIO HR2 VIO HR HR: On Heater in Position # HR2: On Heater 2 in Position #2 (if installed) Fig. 6 - Accessory Electric Heater Control Connections (AC-, AC-2 Units) DEFROST BOARD E-HEAT P3-3 Field Connections ORN TB4 ORN 3 VIO VIO Elec Htr VIO HR2 VIO HR C0833 HR: On Heater in Position # HR2: On Heater 2 in Position #2 (if installed) Fig. 7 - Accessory Electric Heater Control Connections (HP-, HP-2 Except Size 4) C0903 ISTED AIR NDITIONING UIP ACCESS 346N. 23 3 P / N 2-560-4 REV Fig. 8 - Typical 3 -Phase Wiring Installed C0837 7. Replace the center post and secure the single point box to the center post with one screw. (See Fig. 6.) 8. Remove knockouts for appropriate size conduit from unit block-off panel and single point box. Install conduit (rigid or electrometallic tubing) through conduit drip boot as shown. (See Fig. 0.) Drip boot will accept conduit sizes 3/4-in. to -/2 inches. The drip boot eliminates the need for watertight conduit fittings at the single point box. NOTE: Supply wiring must comply with NEC (National Electric Code) and all local requirements. 9. Mark the appropriate block on the unit nameplate for the accessory heater kw installed. Note the required Minimum Circuit Ampacity (MCA) value for this unit-heater combination. Ensure the field power conductors are sized to handle this ampacity. 0. Place adhesive -backed wiring label on flanged side of heater cover.. Fasten heater cover to heater module with 2 screws provided with heater. Flanges of cover should face out. 2. Set manual reset limit switch (on supply fan housing) by depressing button located between the terminals on the switch. (See Fig. 6.) 3. Close single point box cover and secure with one screw. 4. Replace control box cover, using remainder of screws saved from Step 3. 5. Replace indoor and outdoor panels with screws saved from Step 2 (page 8). 6. Turn on unit power. 3

HP - Size 4 ONLY The following text covers installation of single point boxes and electric heaters in the HP- size 4 (2.5 ton) heat pump. For instructions on all the smaller sizes HP- return to page 8. Check sales packages Following the project drawing schedule tables or submittal documents, select the scheduled heaters and single point boxes (if used) and place at each unit. Compare the sales package number(s) for scheduled heater modules against the approved usage table on he unit s infoplate. See Fig. and 2 for typical plate data. If the scheduled heater usage does not appear on the unit infoplate label, STOP. Contact the project engineer or the local distributor sales office for clarification. Open the cartons and inspect for damage. Install Single Point Box (CRSINGLE047A00, 050A00-054A00). Remove kits from boxes and verify that all of the correct parts have arrived undamaged. Control Access Panel 2. If power is already connected to unit, disconnect all power to the unit per correct lock-out tag-out procedures. Disconnect field power wiring at TB and withdraw the wiring from the unit control box. 3. Remove outdoor access, control box, and left indoor access panels from the unit. Fig. 9 shows the unit with the panels already removed. 4. Optional The center post may be removed to facilitate wiring. 5. Remove the bushings and plug from the control panel per Fig. 20. Save the bushings and discard the plug. 6. Add seal strip to the rear bottom corner of the control panel as shown in Fig. 2. 7. Foil tape open screw holes on the back of the single point box as shown in Fig. 2. Different single point boxes will have different screw holes open. Left Indoor Access Panel Outdoor Access Panel Heater Covers Fig. 9 - Typical Unit with Access Panels Removed C070 4

Plug Location Bushings (Re-installed) Single Point Box Mounting Screws Fig. 20 - Single Point Box Installation Details C069 Seal Back Corner 0. The single point box kit will contain two rain shield brackets, a larger bracket with boot seal and a smaller (shorter) bracket without a seal. Remove the seal from the larger bracket and push the conduit drip boot seal into the short rain shield bracket. (See Fig. 22.) Discard the larger bracket. Conduit Drip Boot Seal Bottom Corner Fig. 2 - Seal Strip Locations C027 8. Remove the cover from the single point box. 9. Install the single point box under the control panel with two screws down through the control panel (Fig. 20) and one screw into the center post. (See Fig. 20.) Holes have been provided. Foam wire guides in the center post may have to be removed. If center post was removed per step 4, the single point box will have to be screwed into it later. Rain Shield Bracket Fig. 22 - Rain Shield Installation C067. Install the rain shield bracket to the left and behind the single point box using the two screws and holes provided. 2. Re -install the bushings removed in Step 5. 3. Connect the tap conductors. 5

a. CRSINGLE047A00, 050A00 and 052A00 Connect the blue, yellow, and black power tap conductors (pigtails) from the single point box to the unit s power terminal block TB- per unit label wiring schematic and per Appendix A or B and connection figures. A representative installation of two 480V heaters is shown in Fig. 23, 24, and 25. b. CRSINGLE05A00, 053A00 and 054A00 These kits include two sets of tap conductors (blue, yellow and black pigtails) connected at fuse blocks and 2. Connect these leads in parallel to the unit s power terminal block TB- per the unit label wiring schematic and per Appendix A or B and connection figures. (These kits also include two small terminal blocks (TB0). The TB0 blocks are not used with the HP- size 4 unit; discard.) Install CR288A00-296A00. Remove and save the heater covers. 2. Install heater slide track(s) from the heater kit through the bottom of the heater mounting hole(s) and fasten each with the two screws provided. (See Fig. 27.) 3. Install the heater(s) (Fig. 27, 230V shown) into their mounting location(s) using the screws provided. Tables 2 and 3 give the correct heater location as a function of heater size, voltage, and supply air flow direction. Fig. 23 - Heater Wiring C074 6

Fig. 24 - Typical Single Point Box Wiring C072 Single Point Box Power Wires Fig. 25 - Typical Control Panel Wiring C075 7

Heater Slide Track Mounting Screws Fig. 26 - Heater Slide Track Installation Heater Mount Locations C098 Single Element Heater Module Dual Element Heater Module Fig. 27 - Typical Heaters C068 8

Table 2 Heater Location for Horizontal Return and Discharge* Heater kw Voltage Heater Slot Location CRXXXA00 (V) Left Right 29A 6.5 29A 288A + 29A 26.5 29A 288A 294A 33.5 294A 288A + 294A 43.5 288A 294A 29A + 294A 50.0 29A 294A 292A 6.5 480 292A 289A + 292A 26.5 480 292A 289A 295A 33.5 480 295A 289A + 295A 43.5 480 289A 295A 292A + 295A 50.0 480 292A 295A 293A 6.5 600 293A 290A + 293A 26.5 600 293A 290A 296A 33.5 600 296A 290A + 296A 43.5 600 290A 296A 293A + 296A 50.0 600 293A 296A Table 3 Heater Location for Vertical Return and Discharge* Heater kw Voltage Heater Slot Location CRXXXA00 (V) Left Right 29A 6.5 29A 288A + 29A 26.5 29A 288A 294A 33.5 294A 288A + 294A 43.5 288A 294A 29A + 294A 50.0 29A 294A 292A 6.5 480 292A 289A + 292A 26.5 480 292A 289A 295A 33.5 480 295A (Supply duct opening = ~3 x 6 ) 295A (Supply duct opening = ~36 x 30 ) 289A, 295A, 292A + 295A 50.0 480 292A 295A 293A 6.5 600 293A 290A + 293A 26.5 600 293A 290A 296A 33.5 600 296A 290A + 296A 43.5 600 290A 296A 293A + 296A 50.0 600 293A 296A * XXXA --- 4 digit heater in table. For example, a CR29A000 is listed as a 29A 4. Connect the heater control wiring to terminal block TB4 (located to left of the heaters, see Fig. 33 and 34.) TB4 has five terminals. (See Fig. 28 and 29.) Top row left and center terminals are designated W2 Use and have factory ORN connections. Bottom row left terminal is R Use ; it has a factory RED connection. Bottom row right terminal is C Use ; it has a factory connection. The fifth terminal is for field-option connection of a staging control. CR288A00-293A00 Heaters These heaters have two control wires: ORN for heater contactor and for control common. Connect ORN wire(s) to an available terminal on TB4 s W2 Use group. Connect wire(s) to TB4 s C Use terminal. (Second wire will require use of the piggyback terminal on the factory wire.) (See Fig. 30.) CR294A00-296A00 Heaters These heaters have four control wires: ORN and VIO for heater contactors, RED for safety circuit power and for control common. Connect ORN and VIO wires to TB4 s W2 Use terminals. Connect RED wire to TB4 s R Use. Connect wire to TB4 s C Use terminal. (See Fig. 32.) 24V FPT CB 3.2 AMPS TRAN FROM POWER SCHEMATIC 24V RED GRN/ RED RED EHR 8 6 ORN NOTE 4 AND 6 24V CB 3.2 AMPS ORN TRAN2 FROM POWER SCHEMATIC RED 24V GRN/ ELECTRIC HEAT(ACCESSORY) SEE LABEL DIAGRAM Fig. 28 - TB4 Wiring W2 Use TB4 ORN VIO EHR 0 OFR 0 5 3 24V 24V C056 NOTE: Optional Outdoor Temperature Control at One Heater Stage Move heater wire to this terminal and connect outdoor temperature switch between 2nd and 3rd terminals. R Use C Use Fig. 29 - TB4 Terminal Use C0604 9

5. Cover the heater wiring with the heater covers per Fig. 34. 6. Clean surface if required, and apply warning label next to TB4. (See Fig. 35.) 7. If the center post was removed in Step 4 on page 4, reinstall the center post, screw the single point box to the center post and replace any foam wire guides per step 9. 8. Set manual reset limit switch (on supply fan housing) by depressing button located between the terminals on the switch. 9. Replace all access panels, posts and covers removed in Steps 3 and 7 on page 4. NOTE: Supply wiring must comply with NEC (National Electric Code) and all local requirements. TRAN2 0. Mark the appropriate block on the unit nameplate for the accessory heater kw installed. Note the required Minimum Circuit Ampacity (MCA) value for this unit-heater combination. Ensure the field power conductors are sized to handle this ampacity. Check also that the unit disconnect size and the overcurrent protection device for the branch circuit conductors are suitable for this unit -heater combination.. Run conduit through (rigid or EMT) the conduit drip boot in the rain shield bracket to the single point box. Provide an appropriate fitting to connect the conduit to the single point box wall and ground appropriately. (See Fig. 23.) Drip boot will accept sizes ¾ -in to -/2 in. The drip boot eliminates the need for watertight conduit fittings at the single point box. 2. Run wire through conduit connecting outside power to the designated terminals at the top of the single point box. Ground appropriately. (See Fig. 25.) 3. If all other work on the unit is done, reapply power per lock-out/tag out procedures. RED EHR ORN ORN TB4 ORN ORN TS HC 2 (IF INSTALLED) TB TS HC RED TB4 Fig. 30 - Electric Heater Control Connections-Heat Pump with or 2 CR288A00-293A00 C0562 RED TRAN2 RED EHR ORN ORN TB4 VIO ORN HCR TB HCR2 RED TB4 RED LS HCR HC HCR2 HC2 Fig. 3 - Electric Heater Control Connections-Heat Pump with CR294A00-296A00 C0563 20

RED TRAN2 RED EHR ORN ORN TB4 VIO ORN ORN LS -STG HC 2-STG TB HCR RED HCR2 TB4 RED LS HCR HCR2 Fig. 32 - Electric Heater Control Connections-Heat Pump with CR288A00-293A00 Plus CR294A00-296A00 (2 -Stage Heater) HC HC2 C0564 Terminal Block 4 (TB4) Heater Cover Fig. 33 - Heater Wiring C073 2

Heater Covers Terminal Block 4 (TB4) Fig. 34 - Heater Wiring and Covers C07 -WARNING- THE MAXIMUM ALLOWABLE OUTLET AIR TEMPERATURE IS 93 $C (200 $F) THE MAXIMUM EXTERNAL STATIC IS 0.5 kpa (2.0"W.C.) Fig. 35 - Warning Label C0565 22

APPENDIX A COOLING APPLICATIONS SPB AC --- Units AC --- 2 Units CRSINGLEnnnA00 04---07 08 09---2 4 04---06 07 08---09 NONE Fig. Fig. 037 Fig. 2 Fig. 2 038 Fig. 3 Fig. 3 040 Fig. 4 Fig. 4 042 Fig. 2 Fig. 2 043 Fig. 5 Fig. 5 044 Fig. 6 045 Fig. 7 046 047 Fig. 2 Fig. 2 Fig. 2 049 Fig. 8 Fig. 9 Fig. 8 050 Fig. 0 Fig. 0 Fig. 0 05 Fig. Fig. 2 Fig. Unit Control Box C 3 IFC 3 Field Power Unit Disconnect MOCP 60-A Max Heater Wires Fig. - AC and Heat Pump No Single Point Box C0484 23

HP- SIZE 4 ONLY Unit Control Box TBI 2 3 ALL UNITS EXCEPT HP- SIZE 4 Unit Control Box C IFC 3 3 FIELD POWER CONDUCTORS TAP CONDUCTORS TB UNIT DISCONNECT MOCP 60-A MAX #2 IF USED SPB 037A 042A 047A WIRES Fig. 2 - AC and Heat Pump Single Point Box CRSINGLE037A00, 042A00, 047A00 C0485 Field Tap Power Unit Control Box C 3 IFC!!"5"5 3 Field Power Tap Heater 04 #2 if used Heater 04 # or Heater 05 of to line-side terminals on. Heater Wires Fig. 3 - AC Single Point Box CRSINGLE038A00 C0486 24

Unit Control Box C IFC 3 3 Field Power Tap of to line-side terminals on. Heater Wires Fig. 4 - AC Single Point Box CRSINGLE040A00 Single Phase C0487 Unit Control Box TB-0A C TB-0B IFC 3 3 FIELD POWER CONDUCTOR TAP CONDUCTORS A or 2A CIR CIR 2 of to line-side terminals on. Fig. 5 - AC Single Point Box CRSINGLE043A00 WIRES ALT. TWO MODULES C0489 25

Unit Control Box C IFC 3 3 Field Power Tap TB of to line-side terminals on. Heater Wires Fig. 6 - AC Single Point Box CRSINGLE044A00 C0490 Unit Control Box TB-0A C TB-0B IFC 3 3 FIELD POWER CONDUCTOR TAP CONDUCTORS A or 2A CIR CIR 2 FU4 of to line-side terminals on -FU4. WIRES Fig. 7 - AC Single Point Box CRSINGLE045A00 C049 26

Unit Control Box TB-0A C TB-0B IFC 3 3 FIELD POWER CONDUCTOR TAP CONDUCTORS A or 2A CIR of to line-side terminals on. Fig. 8 - AC Single Point Box CRSINGLE049A00 (Except Size 4) WIRES CIR 2 ALT. TWO MODULES C0489 Unit Control Box C2 TB-0 C $$&:&: IFC 3 3 3 FIELD POWER CONDUCTOR TAP CONDUCTORS 2A CIR 7A or 0A CIR 2 of to line-side terminals on. WIRES Fig. 9 - AC Single Point Box CRSINGLE049A00 (Size 4 Only) C0566 27

Unit Control Box C IFC 3 3 Field Power Tap TB of to line-side terminals on. Heater Wires Fig. 0 - AC Single Point Box CRSINGLE050A00 C0490 Unit Control Box TB-0A C TB-0B IFC 3 3 FIELD POWER CONDUCTOR TAP CONDUCTORS A or 2A CIR CIR 2 FU4 of to line-side terminals on -FU4. WIRES Fig. - AC Single Point Box CRSINGLE05A00 (Except Size 4) C049 28

Unit Control Box C2 TB-0 C IFC 3 3 3 FIELD POWER CONDUCTOR TAP CONDUCTORS 2A CIR FU4 CIR 2 7A or 0A of to line-side terminals on -FU4. WIRES Fig. 2 - AC Single Point Box CRSINGLE05A00 (Size 4 Only) C0567 29

APPENDIX B HEAT PUMP APPLICATIONS SPB CRSINGLEnnnA00 HP --- Units HP --- 2 Units 04---07 08---09 2 4 04---06 NONE Fig. * Fig. * 037 Fig. 2* Fig. 2 038 Fig. 3 Fig. 3 039 Fig. 4 040 Fig. 5 Fig. 5 04 Fig. 6 Fig. 6 047 Fig. 2* Fig. 2* Fig. 2* 049 Fig. 7 Fig. 7 050 Fig. 9 Fig. 9 Fig. 20 05 Fig. 2 Fig. 22 Fig. 23 052 Fig. 24 Fig. 24 Fig. 25 053 Fig. 26 Fig. 27 Fig. 28 054 Fig. 29 Fig. 30 Fig. 3 * Figure is in Appendix A Unit Control Box C IFC!! 7!! 3 3 Field Power Tap HTR of to line-side terminals on. Heater Wires Fig. 3 - Heat Pump Single Point Box CRSINGLE038A00 C0497 30

Unit Control Box C IFC!! 3!! 3 Field Power Tap FU4 HTR HTR 2 of to line-side terminals on -FU4. Heater Wires Fig. 4 - Heat Pump Single Point Box CRSINGLE039A00 C0498 Unit Control Box C 23 Field Power Tap HTR of to line-side terminals on. Heater Wires Fig. 5 - Heat Pump Single Point Box CRSINGLE040A00 -Phase C0499 3

Unit Control Box C!! 23!! Field Power Tap HTR HTR 2 of to line-side terminals on. Heater Wires Fig. 6 - Heat Pump Single Point Box CR04A00 -Phase C0500 Unit Control Box TB-0A C TB-0B IFC 3: 3 Field Power Tap 7A OR 0A of to line-side terminals on. Fig. 7 - Heat Pump Single Point Box CR049A00 (Except Size 2) Heater Wires 08 09 2 C050 32

Unit Control Box C2 TB-0 C IFC 3 3 3 FIELD POWER CONDUCTOR TAP CONDUCTORS of to line-side terminals on. WIRES 7A OR 0A Fig. 8 - Heat Pump Single Point Box CR049A00 (Size 2 Only) C0568 Unit Control Box C IFC!!"7"7 3 3 Field Power Tap TB 6A 4A of TB to line-side terminals on -. 08 08 Heater 6 Wires 09 09 Wires 2 2 NOTE: ALL S CONNECT TO Fig. 9 - Heat Pump Single Point Box CR050A (Except Size 4) C0502 33

Unit Control Box TB 2 3 FIELD POWER CONDUCTOR TB TAP CONDUCTORS CIR 289A of TB to line-side terminals on -. WIRES NOTE: ALL S CONNECT TO 6 WIRES Fig. 20 - Heat Pump Single Point Box CR050A00 (Size 4 Only) CIR 2 292A 4 4 C0569!" Unit Control Box TB-0A C TB-0B IFC 3 3 Field Power Tap CIR FU4 2A CIR 2 of to line-side terminals on -FU4. Heater Wires Fig. 2 - Heat Pump Single Point Box CR05A00 (Except Size 2-4) C0503 34

Unit Control Box C2 TB-0 C IFC 3 3 3 FIELD POWER CONDUCTOR TAP CONDUCTORS 2A CIR FU4 7A or CIR 2 0A of to line-side terminals on -FU4. WIRES Fig. 22 - Heat Pump Single Point Box CR05A00 (Size 2 Only) C0570 Unit Control Box TB 2 3 FIELD POWER CONDUCTOR TAP CONDUCTORS FU4 29A of to line-side terminals on -FU4. WIRES Fig. 23 - Heat Pump Single Point Box CR05A00 (Size 4 Only) 35 C057

!" Unit Control Box C IFC 3 3 Field Power Tap TB FU4 2 of TB to line-side terminals on -FU4. Fig. 24 - Heat Pump Single Point Box CR052A00 (Except Size 4) Heater 08 Wires 09 2 C0504 Unit Control Box TB 2 3 FIELD POWER CONDUCTOR TAP CONDUCTORS TB CIR FU4 294A CIR 2 of TB to line-side terminals on -FU4. WIRES Fig. 25 - Heat Pump Single Point Box CR052A00 (Size 4 Only) 36 C0572

Unit Control Box TB-0A C TB-0B IFC 3 3 Field Power Tap TB CIR FU4 2A CIR 2 FU5 7A of TB to line-side terminals on -FU5. Fig. 26 - Heat Pump Single Point Box CR053A00 (Except Size 2-4) Heater Wires C0505 37

Unit Control Box C2 TB-0 C IFC 3 3 3 FIELD POWER CONDUCTOR TAP CONDUCTORS TB FU4 7A or 0A (when used) 2A CIR FU5 CIR 2 of TB to line-side terminals on -FU5. WIRES Fig. 27 - Heat Pump Single Point Box CR053A00 (Size 2 Only) C0573 38

Unit Control Box TB 2 3 FIELD POWER CONDUCTOR TAP CONDUCTORS TB FU4 288A CIR FU5 294A 29A CIR 2 of TB to line-side terminals on -FU5. WIRES 4 4 Fig. 28 - Heat Pump Single Point Box CR053A00 (Size 4 Only) C0574 39

Unit Control Box TB-OA C TB-OB IFC!! 3!! 3 Field Power Tap TB FU4 CIR FU5 2A CIR 2 FU6 7A of TB to line-side terminals on -FU6. Fig. 29 - Heat Pump Single Point Box CR054A00 (Except Size 2-4) Heater Wires C0506 40

$& $& Unit Control Box C2 TB-0 C IFC 9 3 3 3 FIELD POWER CONDUCTOR TAP CONDUCTORS TB FU4 CIR FU5 2A CIR 2 FU6 7A or 0A of TB to line-side terminals on -FU6. Heater Fig. 30 - Heat Pump Single Point Box CR054A00 (Size 2 Only) C0575 4

Unit Control Box TB 2 3 FIELD POWER CONDUCTOR TAP CONDUCTORS TB FU4 288A or 29A FU5 CIR FU6 294A CIR 2 4 of TB to line-side terminals on -FU6. WIRES Fig. 3 - Heat Pump Single Point Box CR054A00 (Size 4 Only) C0576 42

CRXXXA00 APPENDIX C ELECTRIC DATA SALES PKG NUMBER 0A 02A 03B 04B 05A MODEL NUMBER VOLTS KW 00A 002A 003B 004B 005A 208/ 208/ 208/ 208/ 208/ 3.3/ 4.4 4.9/ 6.5 6.5/ 8.7 7.9/ 0.5 2./ 6.0 FLA --- PH 5.9/ 8.6 23.6/ 27.3 3.2/ 36.2 38.0/ 43.8 --- --- FLA 3 --- PH 9.4/ 0.6 3.8/ 5.7 8./ 20.7 22.2/ 25.3 33.6/ 38.4 QTY CIRS 06A 006A 480 6.0 --- --- 7.0 07A 007A 480 8.8 --- --- 0.5 08A 008A 480.5 --- --- 3.8 09A 009A 480 4.0 --- --- 6.8 0A A 2A 00A 0A 02A 208/ 208/ 208/ 2.0/ 6.0 8.6/ 24.8 24.0/ 32.0 --- --- --- --- 33.3/ 38.5 5.7/ 59.7 66.7/ 77. 3A 03A 480 6.5 --- --- 9.8 4A 04A 480 27.8 --- --- 33.4 5A 05A 480 33.0 --- --- 39.7 6A 06A 480 3.9 --- --- 6.7 7A 07A 208/ 7.8/ 0.4 --- --- --- --- 2.7/ 25.0 8A 08A 600 8.0 --- --- 7.0 9A 09A 600 36.0 --- --- 34.0 264A 264A 208/ 4.9/ 6.5 --- --- 3.5/ 5.6 265A 265A 480 6 --- --- 7.2 266A 266A 480.5 --- --- 3.8 267A 267A 480 4.0 --- --- 6.8 268A 268A 480 23.0 --- --- 27.7 2 269A 269A 480 25.5 --- --- 30.7 2 288A 288A 208/ 7.5/ 0 --- --- 2.3/ 24.5 289A 289A 480 0 --- --- 2. 290A 290A 600 0 --- --- 9.6 29A 29A 208/ 2.4/ 6.5 --- --- 34.5/ 39.7 292A 292A 480 6.5 --- --- 9.9 293A 293A 600 6.5 --- --- 5.9 294A 294A 208/ 25.2/ 33.5 --- --- 70.0/ 80.6 295A 295A 480 33.5 --- --- 40.3 2 296A 296A 600 33.5 --- --- 32.2 2 2 2 2 Used on AC --- HP --- AC --- 2 HP --- 2 04---07 04---07 04---06 08---4 08---2 4 07---09 04---06 07 07 43