Please do not return this product to the store. Contact KETTLER for parts and service: call toll free 866.804.0440 or send email to parts@kettlerusa.com. Please visit our web site www.kettlerusa.com to view a video demonstration of product assembly. USA Adult Assembly Required Assembly instructions Table Tennis Table Oxford 07176-200 13 KETTLER International Inc. 1355 London Bridge Road Virginia Beach, VA 23453 USA www.kettlerusa.com info@kettlerusa.com
Assembly Instructions Before assembling or using the table-tennis table, please read the following instructions carefully. They contain important information for use and maintenance of the equipment as well as for your personal safety. Keep these instructions in a safe place for maintenance purposes or for ordering spare parts. All KETTLER products are designed in accordance with the latest safety regulations and undergo a constant process of quality control during manufacturing. The knowledge gained in this process is used to constantly improve and develop our products. In order to offer our customers the very best in product quality, we reserve the right to make technical changes at any time. In spite of this, should you have any cause for complaint, please contact your KETTLER dealer. Note on Safety The table-tennis table should be used only for its intended purpose, i.e. for playing with suitable table-tennis bats and balls. All other uses are prohibited and may be dangerous. The manufacturer cannot be held liable for damage or injury caused by improper use of the table. Damaged or worn components may endanger your safety or shorten the lifespan of the table-tennis table. Replace worn or damaged components immediately and remove the table from use until this has been done. Use only spare parts manufactured by KETTLER. The table-tennis table complies with all safety regulations. Incorrect repairs, alterations to the design (removal of original parts, addition of other components etc.) may endanger the safety of the user. Instruct other persons (in particular children) using the table in its correct use, and draw their attention to any potential source of danger, especially when setting up or dismantling the table. Caution: While assembly of the product keep off children s reach (Choking hazard - contains small parts). When setting up or dismantling the table, stay clear of its folding radius. When folded up, the table-tennis table presents a large surface to the wind. For this reason, ensure that it is stored in a sheltered position. The table-tennis table may be pushed only into the transport position because there is otherwise a danger of injury. The unit complies with the standard EN 14468 1:2004. Depending on frequency of use, check all screws, bolts etc. regularly to ensure that they are in good condition. Caution: While assembly of the product keep off children s reach (Choking hazard - contains small parts). In case of enquiry, please contact your KETTLER dealer. Handling the equipment Do not use the table-tennis table until it has been fully and correctly assembled and checked. Ensure that table-tennis tables which are not weatherproof are not exposed to dampness or rain. Keep them well away from direct sources of heat. Should the surface become warped, lay the table on a level surface for a few days. Set the table up on a level surface. Do not cover it with plastic foil, under which condensation may form. We recommend the weatherproof KETTLER tarpaulin, art. no. 7032-300. For practising without a partner, the table halves can be folded up singly. For more information on the sport of table-tennis, you are referred to the specialist literature on the subject. Do not use corrosive or abrasive materials to clean the equipment. Ensure that such materials are not allowed to pollute the environment. In most cases, a slightly dampened cloth is sufficient. Waste Disposal: KETTLER products are recyclable. At the end of its useful life please dispose of this article correctly and safely (local refuse sites). Instructions for Assembly The equipment must be assembled with due care by two adult persons. Ensure that you have received all the parts required (see check list) and that they are undamaged. Should you have any cause for complaint, please contact your KETTLER dealer. Before assembling the equipment, study the drawings carefully and carry out the operations in the order shown by the diagrams. The correct sequence is given in capital letters. Please note that there is always a danger of injury when working with tools or doing manual work. Therefore please be careful when assembling this machine. Ensure that your working area is free of possible sources of danger, for example don t leave any tools lying around. Always dispose packaging material in such a way that it may not cause any danger. There is always a risk of suffocation if children play with plastic bags! The fastening material required for each assembly step is shown in the diagram inset. Use the fastening material exactly as instructed. Bolt all the parts together loosely at first, and check that they have been assembled correctly. Tighten the locknuts by hand until resistance is felt, then use spanner to finally tighten nuts completely against resistance (locking device). Then check that all screw connections have been tightened firmly. Attention: once locknuts have been unscrewed they no longer function correctly (the locking device is destroyed), and must be replaced. For technical reasons, we reserve the right to carry out preliminary assembly work (e.g. addition of tubing plugs). Please keep original packaging of this article, so that it may be used for transport at a later date, if necessary. Goods may only be returned after prior arrangement and in (internal) packaging, which is safe for transportation, in the original box if possible. It is important to provide a detailed defect description / damage report! 2
Assembly Instructions List of spare parts When ordering spare parts, always state the full item number, spare-partnumber, the quantity required and the S/N of the product (see spare parts drawing). Example order: Art. no. 07176-200 / spare-part no. 94130003 / 2 pieces / S/N... Important: spare part prices do not include fastening material; if fastening material (bolts, nuts, washers etc.) is required, this should be clearly stated on the order by adding the words with fastening material. USA KETTLER International Inc. 1355 London Bridge Road +1 888 253 8853 Virginia Beach, VA 23453 +1 888 222 9333 www.kettlerusa.com KETTLER LIMITED WARRANTY THERE ARE NO WARRANTIES, EXPRESSED OR IMPLIED, MADE BY EITHER THE DISTRIBUTOR OR THE MANUFACTU- RER ON KETTLER PRODUCTS, EXCEPT THE MANUFACTURER S LIMITED WARRANTY AGAINST DEFECTS IN MATERIAL SET OUT BELOW: This KETTLER Limited Warranty applies to products sold through the KETTLER Authorized Dealer Network to the original retail purchaser and authenticated by proof of purchase from a retailer located in the United States. Any shipments made under this warranty will be shipped to the United States only. Any shipment outside of the United States will be at the sole cost of the customer. This KETTLER Limited Warranty is a manufacturer s warranty and is not changed or modified by additional warranties extended by individual retailers at the point of sale. Manufacturer warrants this product to be free from defects in material at the time of the product s tender of delivery for a period of 3 years for residential use and 1 year for non-residential use. This Limited Warranty is not transferable and does not cover normal wear and tear (including, but not limited to, damage and wear to tires, power shocks, drive belts and other non-durable parts). The liability of the manufacturer under this Limited Warranty shall not include any liability for direct, indirect, or consequential damages resulting from the defect. This Limited Warranty is void if the product is damaged by accident, unreasonable use, improper service, failure to follow instructions provided, modification from its original state, or other causes determined not arising out of defects in material. This warranty gives you specific legal rights. Should this product become defective due to material within the warranty period, contact KETTLER Parts & Service Dept. by phone at 866.804.0440, fax at 757.563.9273, or e-mail at parts@kettlerusa.com. THIS LIMITED WARRANTY IS EXPRESSLY IN LIEU OF ANY OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, AND OF ANY OTHER OBLIGATIONS OR LIABILITY ON THE PART OF THE MANUFACTURER. KETTLER NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT ANY OTHER LIABILITY IN CONNECTION WITH SUCH PRODUCTS. 3
Checklist M6 M8 Checklist (content of bags of screws) Pay attention to the numbering of the bag of screws! 1 1 ø25x8 11,8x64 M8 4 6x ø16 M6 4 M8x45 8x ø16x8 8x M6x50 M8x125 M6x25 5 ø16 ø25x8 M6 2 M8x1 16x ø16x8 M8 3
Checklist (content of bags of screws) Pay attention to the numbering of the bag of screws! 6 8x 2 M6x29 6x ø25x8 M8x45 7 8 ø16 M6 8x 3,9x13 26x19x6 M6x36 M6 15,5x8,3 ø16 Achten Sie auf die Nummerierung der Schraubenbeutel! Pay attention to the numbering of the bag of screws! Prêtez attention à la numérotation des sachets de vis! Let a.u.b. op de nummering van de schroevenzakjes! 9 M6x49 8x M6x60 6x 3,9x16 16,3x3 M6 8x M6 16,12 4,8x25 ø16 Please use the cardboard packaging during mounting as underlay in order to avoid scratching and damaging the product. 1 2 3 1 2 3 You also need the following tools (Not included): 13 5
1 a 1 1 b 1 6
2 a 2 2 b 2 A B 13 ø25 M8x125 ø25 ø25 164 ø16 M8 7
3 a 3 13 M8x1 ø16 M8 3 b 3 13 M8x1 ø16 M8 8
4 a 4 SFL 14 4 b 4! M6 M6x50 6x ø12 M6 9
5 a 5 13 M8 M8x45 ø 25 Now bolt a side connecting rod to the side elements. Note: This bar is used only for support during assembly and must be removed when positioning the other half of the table. 5 b 5 M6x25 ø12 M6
6 a 6 3,9x13 6 b 6 6 c A flat subsurface free from foreign objects is required for assembly step image 6d. For this use the undamaged lid of the packaging box as a subsurface. You must ensure that no screws or other fasteners or foreign objects are on the cardboard base. 11
6 d 6 B A 3,9x13 7 7 13 D! C A C M8x45 ø25 B D M6x30 ø12 26x19x6mm M6 B B ø 25 ø 25 C A: Position one of the table halves and ensure that it cannot slip or tilt over. Ask another person to attach the push bar and the support-frame brace to the last connecting bar. B: To do this, the braces for the frame must be bent slightly to the side. Proceed with care when doing this. C: The connecting bar is now bolted to the side elements. 12
8 8 M6x37 ø15,5x8,3 ø12 M6 9 9 M6x60 ø16,3x3 ø16,12 M6 13
a B A M6x49 ø12 M6 b 3x 3,9x16 14
c B A 4,8x25 d 15
11 Lowering the table halve B A! C Press the right-hand lock (A) and lower the table-half slowly into position (B). Never allow it to drop down! 16
12 Instructions for Assembling the net set 1 Slide the tension pin through net. 2 Place pin in designated slots. 3 Tie tension string to plastic tension tab. 4 Place tension string in slots over tension pin and net post. Adjust net tension by adjusting plastic tension tab. 1 2 3 4 13 Collapsing the table halves C A B Unlock the disk back-up (A). Push the lever of the stabilisation upwards (B) and lift the disk half (C). Maintain the pressure in the initial lifting phase. Bring the disk halves in the upper parking position in which the transport lock automatically clicks into place. max 1 cm = ok. max 1 cm = ok. max 1 cm = ok. 17
Spare parts drawing and list PLEASE ALWAYS QUOTE THE TT TABLE ARTICLE NUMBER AS WELL. item description qty. spare part #. # 07176-200 Oxford outdoor 1 Tennis table top 2 94176200 2 Leg 2 94111129 3 Oval footcap 4 0029 4 Clamp 8 701288 7 Support leg 2 94111130 8 Wheel base 2 94111268 9 Stemtube for non-locking wheel 3437 2 70130812 Locking strut 2 70130900 11 Locking strut with thumb latch 2 941380 12 Safety lever 2 94111120 13 Crossbar M8 2 941155 15 Endcap 40x25mm 4 0009 17 Hand grip for safety lever 2 70130532 18.1 Hardware Bag 1-5 1 94180555 18.2 Hardware Bag 6-1 94180556 19 Shimpad (pair) 1 94180146 20 Net 1 94180355 21 Black PVC tab for net 2 128013 22 Alignment Strut 2 70130604 23 Jbar 4 94111132 25 Eyelet 8 70130830 26 Bushing 8 116011 27 Sideshroud 2 70115022 28 Netpost. bar 2 94111282 29 Netpost. (5674) 2 70130526 30 Ball and racquet holder 1 70130522 31 Guide plug (4439) 2 70130521 32 Plug SFL14 2 0096 33 PVC bushing for wheel base 26x19x6 mm 4 7067 34 PVC footlock 2 70130816 35 Non-locking wheel 4 70130762 36 Locking wheel 4 70130761 37 Stemtube for locking wheel 3508 2 70130815 38 Crossbar M6 1 941156 39 Locking lever 2 70130527 40 Covering 1 07032-600 41 Set of rackets and balls 2 07091-0 18
Spare parts drawing 1 4 40 2 4 17 7 3 12 25 41 13 23 38 M6 M8 25 33 19 22 11 20 31 21 39 28 15 37 26 8 27 29 30 36 34 35 9 32 Heinz Kettler GmbH & Co. KG Haupstrasse 28 D 59463 Ense Parsit D Beispiel Typenschild - Seriennummer GB Example Type label - Serial number F Example Plaque signalétique - Numèro de serie NL Bij voorbeeld Typeplaatje - Seriennummer E Ejemplo Placa identificativa - Número de serie I Esempio Targhetta tecnica - Numero di serie PL Przyklady Tabliczka identyfikacyjna - Numer serii RUS Пример заводской таблички с серийным номером 18.1 18.2 1 1 2 6 2 3 4 5 7 8 9 Made in Germany 19
!! docu 3945/12.15 KETTLER International Inc. 1355 London Bridge Road Virginia Beach, VA 23453 USA www.kettlerusa.com info@kettlerusa.com 20