INSTALLATION INSTRUCTIONS FOR PART 99-5700 APPLICATIONS FORD/JEEP/LINCOLN/MERCURY 99-5700/AT-509FD AW-509FD/DW-550 99-5700 KIT FEATURES DIN Mount Radio Provision Shaft Mount Radio Provision in Select Vehicles ISO Mount Radio Provision in Select Vehicles KIT COMPONENTS A) Radio Housing # B) Radio Housing # C) Brackets Set # (Econoline) D) Bracket # (Escort/Lynx) E) Shaft Supports F) Spacer Set # G) ISO DIN Brackets H) (4) #8 X 3/4 Phillips Pan-Head Screws I) () #6 Self Tapping Screws A B C D E F G H I TOOLS REQUIRED: Cutting Tool Phillips Screwdriver 86-568 Head Unit Removal Keys -800--093 www.metraonline.com Rev. 0--07 COPYRIGHT 004-007 METRA ELECTRONICS CORPORATION INST99-5700
TABLE OF CONTENTS CAR PAGE FORD Aerostar 99-97... Aerostar 985-9... Aspire 994-97... Bronco 99-96... 8 Bronco (full) 987-9... 3 Bronco 980-86... Bronco II 989-90...3 Bronco II 985-88...4 Contour 995-00...4 Crown Victoria 99-94... 5 Crown Victoria 979-90...5 Econoline 99-96... 6 Econoline 975-9... 6 Escort 99-96...7 Escort 985-90...7 Explorer 99-94... 3 F-Series Pickup 99-96... 8 F-Series Pickup 987-9... 3 F-Series Pickup 980-86... Festiva 988-93... 8 LTD 979-90... 5 Mustang 994-00... 9 Probe 993-97... 9 Ranger (mini) 989-94... 3 Ranger (mini) 985-88... 4 Taurus 990-95...0 Taurus 986-89...0 Tempo 989-94... Tempo 985-88... Thunderbird 989-97... Thunderbird 985-88... Windstar 995-98... 3 JEEP Cherokee 984-95... 3 Cherokee 996... 4 Commanche 986-9...3 Grand Wagoneer 987-95...4 Wagoneer 984-96... 3 Wrangler 986-96...5 LINCOLN Continental 988-94...5 Continental 985-87...6 Mark VII 990-9...5 Mark VII 984-89...6 Mark VIII 993-95...7 Town Car 990-94... 5 Town Car 984-89... 7 MAZDA B-Series Pickup 994... 3 66 993-00... 8 MPV 996-99...8 MX3 99-96... 8 MX6 993-97... 8 Navajo 99-94... 3 Protege 995-00...9 MERCURY Capri XR 99-94... 9 CAR PAGE MERCURY (cont.) Cougar 989-97... Cougar 985-88... Grand Marquis 99-94... 5 Grand Marquis 979-90... 5 Lynx 985-90... 7 Mystique 995-99...4 Marquis 979-90... 5 Sable 990-95... 9 Sable 986-89... 0 Topaz 989-94... Topaz 985-88... Tracer 99-96... 7 Tracer (hatch) 989-90... 0 Villager 993-96...0 NISSAN Quest 993-95... 0 ADDITIONAL VEHICLES: ACURA Integra 986-89... Legend 986-89... ALFA ROMEO Milano 980-89... Spider Veloce 987-93... 64 L/S 99-93... AUDI 80/90 988-96... 00/00 989-95... 4000 980-87... 5000 978-88... S4 99-93... BMW 3-Series 977-96... 5-Series 975-96... 6-Series 977-89... 7-Series 978-96... 8-Series 99-93... DAIHATSU Charade 989-9... DODGE Colt 993-94... D50 Pickup 988-93... EAGLE Summit 993-95... FIAT Brava 979-83... Spider 988-89... Strada 977-83... X9 979-89... GEO Metro 989-9... Tracker 989-9... HONDA Accord 98-89... CRX 984-9... *Note: Refer also to the instructions included with the aftermarket radio. CAR PAGE HONDA (cont.) Civic 98-95... Del Sol 993-96... Prelude 983-9... JAGUAR XJ6 988-93... LANCIA Beta 979-8... MASERATI Spyder 985-90... MERCEDES 40/80/300/380/40/450 500SLC/SEL 970-96... MITSUBISHI Mighty Max 987-95... Mirage 993-96... PEUGEOT 405 989-93... 505 984-93... PONTIAC LeMans 988-93... PORSCHE 9 973-96... 94 977-8... 94S 986-88... 98 980-96... 944 986-93... 968 99-96... RENAULT Alliance 984-85... Encore 984-85... Fuego 98-85... LeCar 976-83... 8i 979-83... SAAB 900 979-96... 9000 986-96... STERLING 85 987-88... 87 989-9... SUZUKI Samurai 988½-93... Sidekick 989-9... Swift 989-9... X-90 996-97... VOLKSWAGEN Bus 968-79... Cabriolet 985-93... Dasher 976-8... Fox 987-93... Golf 985-98... Passat 990-99... Pickup 980... Rabbit 975-80... Scirocco 98-88... Super Beetle 973-79... Quantum 98-88... Vanwagon 980-9...
FORD Aerostar 99-97 () screws from the steering column trim panel and () screws from the ashtray cavity. Unclip the dash trim bezel. Using Metra's 86-568, pull the factory head unit from the dash and disconnect the wiring. FORD Aerostar 985-9 "D" "F" () Phillips screws from the base of the dash trim bezel. Pry down on the () tabs located at the top of the dash trim bezel and remove the bezel. Remove (4) screws securing the factory head unit and disconnect the wiring. Housing # EXCEPT tabs "D" and "F". The mounting tabs can be identified by the stamped letter on the back of each tab. Locate Spacer Set #. (The Spacers must be placed behind the mounting tabs during installation in step #5). Skip to the Installation Instructions for ALL VEHICLES on Page #.
FORD Aspire 994-97 Metra's 86-568, pull the factory head unit FORD Bronco / Pickup 980-86 "B" "B" () screws from the top edge of the dash trim bezel. Pull out on the top of the bezel, unhook the base and remove the bezel. If a factory head unit is NOT present, scribe the (4) mounting holes and radio opening onto the bezel. Drill the holes, cut the opening and place (4) U-clips over the mounting positions. Housing # EXCEPT tabs "B". The mounting tabs can be identified by the stamped letter on the back of each tab. Skip to the Installation Instructions for ALL VEHICLES on Page #.
FORD Bronco (full size) / F-Series Pickup 987-9 "D" "F" prevent an accidental short circuit. Carefully pull and remove the dash trim bezel. Remove (4) screws securing the factory head unit and disconnect the wiring. Housing # EXCEPT tabs "D" and "F". The mounting tabs can be identified by the stamped letter on the back of each tab. Locate Spacer Set #. (The Spacers must be placed behind the mounting tabs during installation in step #5). Skip to the Installation Instructions for ALL VEHICLES on Page #. FORD Bronco II 989-90 / Explorer 99-94 / Ranger 989-94 MAZDA Navajo 99-94 / B-Series Pickup 994 the ashtray and () screws exposed in the ashtray cavity. Using Metra's 86-568, pull the factory head unit from the dash and disconnect the wiring. 3
FORD Bronco II / Ranger 985-88 "D" "F" (4) Phillips screws from the top edge of the dash trim bezel. Remove the light switch knob, cigarette lighter and ashtray. Unsnap the molding located below the dash trim bezel and remove (4) screws exposed. Remove (4) screws securing the factory head unit and disconnect the wiring. Housing # EXCEPT tabs "D" and "F". The mounting tabs can be identified by the stamped letter on the back of each tab. Locate Spacer Set #. (The Spacers must be placed behind the mounting tabs during installation in step #5). Skip to the Installation Instructions for ALL VEHICLES on Page #. FORD Contour 995-00 / MERCURY Mystique 995-99 Metra's 86-568, pull the factory head unit 4
FORD Crown Victoria 99-94 MERCURY Grand Marquis 99-94 Metra's 86-568, pull the factory head unit FORD Crown Victoria / LTD 979-90 MERCURY Grand Marquis / Marquis 979-90 "D" "F" prevent an accidental short circuit. Open the ashtray and remove () Phillips screws securing the dash trim bezel. Remove (4) screws securing the factory head unit and disconnect the wiring. 5 Housing # EXCEPT tabs "D" and "F". The mounting tabs can be identified by the stamped letter on the back of each tab. Locate Spacer Set #. (The Spacers must be placed behind the mounting tabs during installation in step #5). Skip to the Installation Instructions for ALL VEHICLES on Page #.
FORD Econoline 99-96 the light switch knob and unscrew the surrounding trim. Remove the cupholder and the screws exposed in the cupholder cavity. Unsnap the () trim bezel inserts and remove the screws exposed. Remove the lower steering column trim panel and unclip the dash trim bezel. Using Metra's 86-568, pull the factory head unit from the dash and disconnect the wiring. FORD Econoline 975-9 (3) screws from the lower edge of the dash trim bezel. Remove () screws above the radio opening. Unsnap the right corner of the dash trim bezel, disconnect the cigarette lighter wiring and remove the bezel. Remove the screws securing the factory head unit and disconnect the wiring. 6 Housing #. The mounting tabs can be identified by the stamped letter on the back of each tab. Slide Bracket Set # into the slots on the sides of the Housing. Skip to the Installation Instructions for ALL VEHICLES on Page #.
FORD Escort / MERCURY Tracer 99-96 Metra's 86-568, pull the factory head unit FORD Escort / MERCURY Lynx 985-90 "B" (4) screws from the top edge of the dash trim bezel. Remove () screws from the bottom edge of the dash trim bezel. Remove the climate control knobs and remove the bezel. Remove (4) hex-head screws securing the factory head unit and disconnect the wiring. 7 Housing # EXCEPT tabs "B". The mounting tabs can be identified by the stamped letter on the back of each tab. Mount Bracket # to the bottom of the Housing with () #8 x ¾" Phillips Screws supplied. Skip to the Installation Instructions for ALL VEHICLES on Page #.
FORD F-Series Pickup / Bronco 99-96 Metra's 86-568, pull the factory head unit FORD Festiva 988-93 "C" (4) Phillips screws from the bottom of the dash trim bezel. Remove the bezel. Remove () screws securing the factory head unit and disconnect the wiring. 8 Housing # EXCEPT tabs "C". The mounting tabs can be identified by the stamped letter on the back of each tab. Skip to the Installation Instructions for ALL VEHICLES on Page #.
FORD Mustang 994-00 Metra's 86-568, pull the factory head unit FORD Probe 993-97 () screws from the base of the dash trim bezel. Unclip and remove the bezel. Using Metra's 86-568, pull the factory head unit 9
FORD Taurus / MERCURY Sable 990-95 Metra's 86-568, pull the factory head unit FORD Taurus / MERCURY Sable 986-89 "A" "G" () 7mm hex-head screw from the bottom of the radio trim bezel. Gently unclip the bezel and disconnect the antenna switch power lead. Remove (4) screws securing the factory head unit and disconnect the wiring. 0 Housing # EXCEPT tabs "A" and "G". The mounting tabs can be identified by the stamped letter on the back of each tab. Skip to the Installation Instructions for ALL VEHICLES on Page #.
FORD Tempo / MERCURY Topaz 989-94 Metra's 86-568, pull the factory head unit Cut and remove the shaft supports from the Faceplate. Skip to step #3c in the Installation Instructions for ALL VEHICLES on Page #. FORD Tempo / MERCURY Topaz 985-88 "A" "A" the ashtray by disengaging the release tab at the rear of the ashtray bracket. Remove () screws from the lower edge of the dash trim bezel. Unclip the top edge of the bezel and remove. Remove (4) screws securing the factory head unit and disconnect the wiring. Housing # EXCEPT tabs "A". The mounting tabs can be identified by the stamped letter on the back of each tab. Skip to the Installation Instructions for ALL VEHICLES on Page #.
99-5700 FORD Thunderbird / MERCURY Cougar 989-97 Metra's 86-568, pull the factory head unti FORD Thunderbird / MERCURY Cougar 985-88 "D" "F" () screws from the top of the dash trim bezel. Open the ashtray and remove () screws from the ashtray cavity. Remove (4) screws securing the factory head unit and disconnect the wiring. Housing # EXCEPT tabs "D" and "F". The mounting tabs can be identified by the stamped letter on the back of each tab. Locate Spacer Set #. (The Spacers must be placed behind the mounting tabs during installation in step #5). Skip to the Installation Instructions for ALL VEHICLES on Page #.
FORD Windstar 995-98 Metra's 86-568, pull the factory head unit JEEP Cherokee 984-95 / Commanche 986-9 Wagoneer 984-96 "E" prevent an accidental short circuit. Unsnap the steering column trim panel and remove. Remove (4) screws from the dash trim bezel and remove the bezel. Remove () screws securing the factory head unit and disconnect the wiring. 3 Housing # EXCEPT tabs "E". The mounting tabs can be identified by the stamped letter on the back of each tab. Skip to the Installation Instructions for ALL VEHICLES on Page #.
JEEP Cherokee 996 "E" (3) torx-head screws from the steering column trim panels. Unscrew the tilt steering lever and unsnap the trim panels. Remove (4) screws from the dash trim bezel and remove the bezel. Remove () screws securing the factory head unit and disconnect the wiring. Housing # EXCEPT tabs "E". The mounting tabs can be identified by the stamped letter on the back of each tab. Skip to the Installation Instructions for ALL VEHICLES on Page #. JEEP Grand Wagoneer 987-95 "E" prevent an accidental short circuit. Gently unclip the dash trim bezel. Remove () screws securing the factory head unit and disconnect the wiring. 4 Housing # EXCEPT tabs "E". The mounting tabs can be identified by the stamped letter on the back of each tab. Skip to the Installation Instructions for ALL VEHICLES on Page #.
JEEP Wrangler 986-96 "B" (6) Phillips screws from the face of the dash trim bezel. Remove the bezel. Remove () screws securing the factory head unit and disconnect the wiring. Housing # EXCEPT tabs "B". The mounting tabs can be identified by the stamped letter on the back of each tab. Skip to the Installation Instructions for ALL VEHICLES on Page #. LINCOLN Continental 988-94 / Mark VII 990-9 Town Car 990-94 Metra's 86-568, pull the factory head unit 5
99-5700 LINCOLN Continental 985-87 "D" "F" () #8 Phillips screws below the radio opening. Open the ashtray and remove () #8 Phillips screws exposed (it is NOT necessary to remove the center screw). Unclip and remove the dash trim bezel. Remove (4) hex-head screws securing the factory head unit and disconnect the wiring. Housing # EXCEPT tabs "D" and "F". The mounting tabs can be identified by the stamped letter on the back of each tab. Locate Spacer Set #. (The Spacers must be placed behind the mounting tabs during installation in step #5). Skip to the Installation Instructions for ALL VEHICLES on Page #. LINCOLN Mark VII 984-89 "D" "F" prevent an accidental short circuit. Gently pry out on the dash trim bezel and remove. Remove (4) 5mm hex-head sheet metal screws securing the factory head unit and disconnect the wiring. 6 Housing # EXCEPT tabs "D" and "F". The mounting tabs can be identified by the stamped letter on the back of each tab. Locate Spacer Set #. (The Spacers must be placed behind the mounting tabs during installation in step #5). Skip to the Installation Instructions for ALL VEHICLES on Page #.
LINCOLN Mark VIII 993-95 Metra's 86-568, pull the factory head unit LINCOLN Town Car 984-89 "D" "F" (3) #8 Phillips screws from the bottom of the radio trim bezel. Unsnap the plastic strip located above the bezel and remove (3) Phillips screws exposed. Gently pull the instrument cluster trim bezel away from the dash and remove the radio trim bezel. Remove (3) hex-head screws securing the factory head unit and disconnect the wiring. 7 Housing # EXCEPT tabs "D" and "F". The mounting tabs can be identified by the stamped letter on the back of each tab. Locate Spacer Set #. (The Spacers must be placed behind the mounting tabs during installation in step #5). Skip to the Installation Instructions for ALL VEHICLES on Page #.
MAZDA MPV 996-99 prevent an accidental short circuit. Unsnap the side trim pieces from the factory head unit. Using Metra's 86-568, pull the unit MAZDA MX3 99-96 Metra's 86-568, pull the factory head unit MAZDA MX6 993-97 / 66 993-00 Metra's 86-568, pull the factory head unit 8
MAZDA Protege 995-00 the ashtray and () screws from the ashtray cavity. Using Metra's 86-568, pull the factory head unit from the dash and disconnect the wiring. MERCURY Capri XR 99-94 Metra's 86-568, pull the factory head unit 9
MERCURY Tracer (hatchback) 989-90 (3) Phillips screws from the top of the dash trim bezel. Remove the ashtray and () Phillips screws from the bottom of the bezel. Remove (4) Phillips screws securing the factory head unit and disconnect the wiring. MERCURY Villager 993-96 / NISSAN Quest 993-95 () screw above the climate controls. Unclip the dash trim bezel. Using Metra's 86-568, pull the factory head unit from the dash and disconnect the wiring. 0
ALL VEHICLES 3a Fig. A AEROSTAR 985-9, BRONCO 987-9, Fig. B BRONCO II 985-88, CROWN VICTORIA 979-90, ECONOLINE 975-9, ESCORT 985-90, F-SERIES PICKUP 987-9, LTD 979-84, RANGER 985-88, TAURUS 986-89, THUNDERBIRD 985-88, CONTINENTAL 985-87, MARK VII 984-89, TOWN CAR 984-89, COUGAR 985-88, GRAND MARQUIS 979-90, LYNX 985-90, MARQUIS 979-90, SABLE 986-89, TRACER (hatchback) 988-90, all JEEPS: For DIN units, slide the DIN cage into Radio Housing # and secure by bending the metal locking tabs down. For ISO-DIN units, and slide the head unit into the back of the kit. Attach the ISO-DIN Brackets to the Housing legs, align the Bracket holes with the unit holes and secure the Brackets with ()#6Self-tapping Screws. (see Fig.B) Slide the aftermarket head unit into the cage until secure.(see Fig. A). 3b Fig. A Fig. B BRONCO 980-86, F-SERIES PICKUP 980-86, FESTIVA 988-93, TEMPO 985-88, TOPAZ 985-88: For -Shaft units, slide the aftermarket head unit into Radio Housing # and secure with shaft nuts. (see Fig. A). For Din units, cut and remove the shaft supports from Radio Housing #. Slide the DIN cage into the Housing and secure by bending the metal locking tabs down. Slide the aftermarket head unit into the cage until secure. (seefig. B)
3c Fig. A Fig. B AEROSTAR 99-97, BRONCO II 989-90, EXPLORER 99-94, RANGER 989-94, CROWN VICTORIA 99-94, GRAND MARQUIS 99-94, ECONOLINE 99-96, ESCORT 99-96, TRACER (sedan) 99-96, F-SERIES PICKUP 99-96, BRONCO 99-96, TAURUS 990-95, SABLE 990-95, TEMPO 989-94, TOP AZ 989-94, THUNDERBIRD 989-97, COUGAR 989-97, CONTINENTAL 988-94, MARK VII 990-9, TOWN CAR 990-94, MARK VIII 993-95, ASPIRE, B-SERIES PICKUP, CONTOUR, MYSTIQUE, MUSTANG, PROBE, WINDSTAR, MPV, MX3, MX6, PROTEGE, 66, CAPRI XR, VILLAGER, QUEST: For DIN units, Slide the DIN cage into the dash and secure by bending the metal locking tabs down.slide the aftermarket head unit into the cage until secure. (see Fig. A). For -Shaft units, make wiring connections and slide the aftermarket unit into the dash. Slide the Shaft Supports over the radio shafts and position them along the inner lip of the radio opening. Place the faceplate against the outer lip of the radio opening and secure with shaft nuts. (see Fig.B) 4 5 A B C D (Taurus / Sable application shown) A) Strip wire ends back ½" B) Twist ends together C) Solder D) Tape Locate the factory wiring harness in the dash. Metra recommends using the proper mating adaptor and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit). Re-connect the battery terminal and test the unit for proper operation. Mount the head unit/kit assembly to the sub-dash with those screws previously removed.