tough. Live Centers Face Drivers 2013/2014

tough. Live Centers Face Drivers 2013/2014 www.roehm.biz

LIVE CENTERS - FACE DRIVERS Revolving tailstock centres Basic 2005 Heavy 2009 Speed 2011 Slim 2012 Control 2014 Flex 2015 Revolving centering tapers MZK 2018 Dead centres FKS 2020 Constant Face Drivers CoE 2024 Accessories CoE 2025 CoE - Assortments 2025 CoA 2026 Accessories CoA 2029 CoA - Assortments 2033 CoM 2034 Driving head CoM 2035 Driving discs CoM 2035 Accessories CoM 2036 CoB 2037 Driving heads CoB 2038 Accessories CoB 2042 Power-operated Face Drivers CoK 8-80 mm 2044 Accessories CoK 2045 CoK 50-250 mm 2047 Driving discs CoK 2048 Accessories CoK 2049 Power-operated Driving Heads CoK 2050 Accessories CoK 2054 Errors and corrections are reserved! www.roehm.biz 1

Live Centers - Face Drivers Revolving tailstock centres 2002 Revolving centering tapers 2018 Dead centres 2020 Constant Face Drivers CoE 2023 Constant Face Drivers CoA 2026 Constant Face Drivers CoM 2034 Constant Face Drivers CoB 2037 Power-operated Constant Face Drivers CoK 2043 Errors and corrections are reserved!

Operation Guide Revolving tailstock centres 60 Basic - carbide insert Revolving tailstock centres MKS Type Size MT Workpiece weight max (kg) Concentricity deviation Type 604 HM Basic - carbide insert Body hardened and ground Type 604 HMG Basic - with draw-off nut and carbide insert Body hardened and ground 1 2 3 4 5 6 2 3 4 5 6 60 120 360 500 1000 1800 120 360 500 1000 1800 0,005 0,01 0,005 0,01-1 7000 7000 5000 3800 3000 2600 7000 5000 3800 3000 2600 Speed max min Page 2005 2005 Basic Type Size MT Workpiece weight max (kg) Concentricity deviation Type 604 HP Basic - precision design Body hardened and ground Type 601 N Basic - economy design Body ground 2 3 4 5 0 1 2 3 4 5 200 500 800 2000 10 80 180 300 750 1800 0,003 0,01 0,005-1 7000 5000 3800 3000 15000 7000 7000 6300 3800 3000 Speed max min Page 2007 2007 Heavy Type Size MT Workpiece weight max (kg) Concentricity deviation Type 640-20 Heavy - standard design Body hardened and ground Type 640-80 Heavy - standard design with draw-off nut Body hardened and ground Type 604 Heavy - heavy duty design Body hardened and ground 4 5 6 4 5 6 6 7 Metr. 80 Metr. 100 Metr. 120 Nr. 80 Nr. 100 Nr. 120 1000 2000 3000 1000 2000 3000 5000 9000 8500 13000 22000 8500 13000 22000 0,005 0,005 0,01 0,015 0,02 0,015 0,01 0,01 0,01-1 7000 6000 4800 7000 6000 4800 1500 1500 1500 1000 800 1500 1000 800 Speed max min Page 2009 2009 2010 Slim Type Size MT Workpiece weight max (kg) Concentricity deviation Type 600 Slim - standard design Body hardened and ground Type 600-20 Slim - extended live centre with draw-off nut Body hardened and ground 2 3 4 5 6 2 3 4 5 6 200 400 800 1600 3500 170 340 700 1400 3000 0,005 0,01 0,02 0,008 0,01 0,02-1 7000 7000 6300 4300 3000 7000 7000 6300 4300 3000 Speed max min Page 2012 2012 Type Size MT Workpiece weight max (kg) Concentricity deviation Type 652 AC Control - standard design Body hardened and ground Control Type 652 AC-VL Control - extended live centre Body hardened and ground 3 4 5 6 3 4 5 6 400 800 1600 3200 260 550 1100 2500 0,01 0,015 0,01 0,015-1 4000 3500 2500 1800 4000 3500 2500 1800 Speed max min Page 2014 2014 2002

Operation Guide Revolving tailstock centres 60 Basic - standard design Type Size MT Workpiece weight max (kg) Concentricity deviation Type 604 H Basic - standard design Body hardened and ground Type 604 HG Basic - standard design with draw-off nut Body hardened and ground 1 2 3 4 5 6 metr. 80 2 3 4 5 6 100 200 500 800 2000 5000 8500 200 500 800 2000 3500 0,005 0,01 0,015 0,005 0,01-1 7000 7000 5000 3800 3000 1500 1500 7000 5000 3800 3000 2600 Speed max min Revolving tailstock centres MKS Page 2006 2006 Type Size MT Workpiece weight max (kg) Concentricity deviation Type 604 HVL Basic - extended live centre Body hardened and ground Basic - extended live centre Type 604 HVLN Basic - extended live centre with profiled centre point Body hardened and ground 1 2 3 4 5 6 2 3 4 5 80 140 400 500 1200 2500 100 150 180 280 0,01 0,005 0,01 0,005-1 7000 7000 5000 3800 3000 2600 7000 5000 3800 3000 Speed max min Page 2008 2008 Speed Type Size MT Workpiece weight max (kg) Concentricity deviation Type 663 Speed - with draw-off nut for especially high speeds - different head dia. at same shank Body hardened and ground Type 664 Speed - extended NC-centre with carbide insert for especially high speed Body hardened and ground 4 5 6 2 3 4 5 800 1250 2500 100 100 250 250 0,005 0,01-1 10000 10000 7000 12000 12000 9000 9000 Speed max min Page 2011 2011 Type Size MT Workpiece weight max (kg) Concentricity deviation Slim Type 600-20 Slim - extended live centre with profiled centre point Body hardened and ground 2 3 4 5 50 100 150 180 0,005-1 7000 7000 6300 4300 Speed max min Page 2013 2003

Revolving tailstock centres 60 Technical features The revolving tailstock centres have been re-engineerd in function and design. Due to the new features they are even better in daily use and offer additional advantages. Revolving tailstock centres MKS Even longer life due to: - Splash water groove - Improved lubrication NEW - Close toleranced bearing seat Lower interference shape due to: - Slim housing Body hardened and ground Centre hardened, repeated regrinding at will Triple bearing method High runout accuracy Life-time lubrication High speeds Heavy duty Long life Various type suitable to different applications Shaft bore hole for easy and professional dismounting. Big and secure supporting surface to ensure the complete axial bearing load. High-precision needle bearing High precision roller bearings Reliable lip seal protects bearing space from ingress by dirt and coolant. Reduced friction and heating. Revolving tailstock centres also available with special design live centres Shaft ground true to gauge. Drop-forged body with high-load capacity due to uniform fibre flow; hardened and ground. Head design with bevelling for unhindered approach of tool holder and lathe tools. Live centre made of water-resistant tool steel, drop-forged and through-hardened to withstand repeated regrinding, shank-bedded. Splash water groove as an additional protection against splash water penetration. 2004

Revolving tailstock centres Basic - carbide insert Revolving tailstock centres MKS Type 604 HM Basic with carbide insert body hardened and ground - tip angle 60 Item no. 225297 032140 090089 237413 093306 221016 221017 Mount MT 1 2 3 3 4 5 6 Size 101 102 104 106 108 110 114 A 60,5 65 70,5 79,5 102,5 129 152 B 34,5 43 48,5 58,5 68,5 88,5 102,5 C 7 11 11 14 14 18 18 D 15 20 22 25 32 40 50 G 12,065 17,78 23,825 23,825 31,267 44,399 63,348 K 17 24 27,5 31 41 50,5 57,5 Weight 400 600 900 1300 2300 4700 10000 Workpiece weight max. kg 60 120 240 360 500 1000 1800 Concentricity deviation 0,005 0,005 0,005 0,005 0,005 0,005 0,01 Speed max. min -1 7000 7000 6300 5000 3800 3000 2600 Spare live centres 1241741 1241742 1241743 1241744 1241745 1241746 1241747 Type 604 HMG Basic with draw-off nut and carbide insert body hardened and ground - tip angle 60 Item no. 221021 221022 221023 221024 221025 221026 Mount MT 2 3 3 4 5 6 Size 102 104 106 108 110 114 A 65 70,5 79,5 102,5 129 152 B 45 50 60 70 90 105 C 11 11 14 14 18 18 D 20 22 25 32 40 50 G 17,78 23,825 23,825 31,265 44,399 63,348 K 24 27,5 31 41 50,5 57,5 M 56 62 74 82 105 120 Weight 600 1000 1400 2400 5200 10500 Workpiece weight max. kg 120 240 360 500 1000 1800 Concentricity deviation 0,005 0,005 0,005 0,005 0,005 0,01 Speed max. min -1 7000 6300 5000 3800 3000 2600 Spare live centres 1241742 1241743 1241744 1241745 1241746 1241747 2005

Revolving tailstock centres Basic - standard design Revolving tailstock centres MKS Type 604 H Basic body hardened and ground - tip angle 60 Item no. 043400 043115 042315 042776 042175 042843 043532 093439 093440 Mount MT 1 2 3 3 4 5 6 6 Metr. 80 Size 101 102 104 106 108 110 114 116 116 A 60,5 65 70,5 79,5 102,5 129 152 196 196 B 34,5 43 48,5 58,5 68,5 88,5 102,5 138 138 D 15 20 22 25 32 40 50 60 60 G 12,065 17,78 23,825 23,825 31,267 44,399 63,348 63,348 80 K 17 24 27,5 31 41 50,5 57,5 67 68 Weight 400 500 800 1300 2300 4700 10200 17800 23000 Workpiece weight max. kg 100 200 400 500 800 2000 3500 5000 8500 Concentricity deviation 0,005 0,005 0,005 0,005 0,005 0,005 0,008 0,01 0,015 Speed max. min -1 7000 7000 6300 5000 3800 3000 2600 1500 1500 Spare live centres 1241726 1241725 1241724 1241723 1241722 1241721 1241728 1241729 1241730 Type 604 HG Basic with draw-off nut body hardened and ground - tip angle 60 Item no. 221018 221019 205036 207148 074390 221020 Mount MT 2 3 3 4 5 6 Size 102 104 106 108 110 114 A 65 70,5 79,5 102,5 129 152 B 45 50 60 70 90 105 D 20 22 25 32 40 50 G 17,78 23,825 23,825 31,267 44,399 63,348 K 24 27,5 31 41 50,5 57,5 M 56 62 74 82 105 120 Weight 600 1000 1400 2400 5200 10500 Workpiece weight max. kg 200 400 500 800 2000 3500 Concentricity deviation 0,005 0,005 0,005 0,005 0,005 0,008 Speed max. min -1 7000 6300 5000 3800 3000 2600 Spare live centres 1241725 1241724 1241723 1241722 1241721 1241728 2006

Revolving tailstock centres Basic - precision design Revolving tailstock centres MKS Type 604 HP Basic precision design body hardened and ground - tip angle 60 Item no. 082392 318227 082394 082395 1263871 Mount MT 2 3 4 5 6 Size 102 106 108 110 114 A 65 82 102,5 129 152 B 43 55 68,5 88,5 102,5 D 20 25 32 40 50 G 17,78 23,825 31,267 44,399 63,348 K 24 30,5 41 50,5 57,5 Weight 500 1300 2300 4700 10200 Workpiece weight max. kg 200 500 800 2000 3500 Concentricity deviation 0,003 0,003 0,003 0,003 0,003 Speed max. min -1 7000 5000 3800 3000 2600 Spare live centres 1241725 1243613 1241722 1241721 1241728 Basic - economy design Workpiece inkg 8000 6300 5000 4000 3150 2500 2000 1600 1250 1000 800 630 500 400 315 250 200 160 125 100 80 63 50 40 31,5 25 20 Radial load Workpiece in kg Service life of roller bearings: 2000 operating hours 101 MK 1 25 35 45 70 100 130 190 270 350 500 800 1000 1500 2200 3000 4000 6000 16000 12500 10000 8000 6300 5000 4000 3150 2500 2000 1600 1250 1000 800 630 500 400 315 250 200 160 125 100 80 63 50 40 101 und 102 N 110 MK 4 108 MK 3 104 MK 3 102 MK 2 Axial load indan min - 1 min - 1 Axial load Axial load in dan Service life of roller bearings: 2000 operating hours 110 N 108 N 104 N 25 35 45 70 100 130 190 270 350 500 800 1000 1500 2200 3000 4000 6000 Type 601 N Basic body only ground not hardened - tip angle 60 Item no. 061740 043395 043111 042310 042171 042839 Mount MT 0 1 2 3 4 5 Size 100 101 102 104 108 110 A 44 60,5 65 70,5 102,5 129 B 25 34,5 43 48,5 68,5 88,5 D 10 15 20 22 32 40 G 9,045 12,065 17,78 23,825 31,267 44,399 K 11 17 24 27,5 41 50,5 Weight 200 400 500 800 2300 4700 Workpiece weight max. kg 10 80 180 300 750 1800 Concentricity deviation 0,01 0,005 0,005 0,005 0,005 0,005 Speed max. min -1 15000 7000 7000 6300 3800 3000 Spare live centres 1241727 1241726 1241725 1241724 1241722 1241721 2007

Revolving tailstock centres Basic - extended live centre Revolving tailstock centres MKS Type 604 HVL Basic with extended live centre body hardened and ground - tip angle 60 Item no. 058668 058669 058670 058671 058672 058673 Mount MT 1 2 3 4 5 6 Size 101 102 106 108 110 114 A 70,5 75 95,5 114,5 143,5 172,5 B 34,5 43 58,5 68,5 88,5 102,5 D 15 20 25 32 40 50 G 12,065 17,78 23,825 31,267 44,399 63,348 K 27 34 47 53 65 78 J 9 10 12 14 16 18 Weight 400 500 1300 2300 4800 10200 Workpiece weight max. kg 80 140 400 500 1200 2500 Concentricity deviation 0,01 0,005 0,005 0,005 0,005 0,01 Speed max. min -1 7000 7000 5000 3800 3000 2600 Spare live centres 1241731 1241732 1241733 1241734 1241735 1241736 Type 604 HVLN Basic with profiled centre point body hardened and ground - tip angle 60 Item no. 1241689 1241691 1241693 1241694 Mount MT 2 3 4 5 Size 102 106 108 110 A 75 95,5 114,5 143,5 B 43 58,5 68,5 88,5 D 20 25 32 40 G 17,78 23,825 31,267 44,399 K 34 47 53 65 P 8 10 12 14 R 16 20 26 30 Workpiece weight max. kg 100 150 180 280 Speed max. min -1 7000 5000 3800 3000 Spare live centres 1243677 1243678 1243679 1243680 2008

Revolving tailstock centres Heavy - standard design Radial load Workpiece in kg Service life of roller bearings: 2000 operating hours Axial load Axial load in dan Service life of roller bearings: 2000 operating hours Workpiece in kg 5000 4000 3150 2500 2000 1600 1250 1000 800 630 426 + 486 425 + 485 424 + 484 Axial load in dan 4000 3150 2500 2000 1600 1250 1000 800 630 500 400 315 426 + 486 425 + 485 424 + 484 Revolving tailstock centres MKS 280 355 450 560 710 900 1120 1400 1800 2240 2800 3550 4500 5600 7100 9000 min - 1 min - 1 280 355 450 560 710 900 1120 1400 1800 2240 2800 3550 4500 5600 7100 9000 Type 640-20 Heavy especially for high load at high speeds body hardened and ground - tip angle 60 Item no. 303598 303599 301696 Mount MT 4 5 6 Size 424 425 426 A 122 150 180 B 70 95 120 D 32 42 58 G 31,267 44,399 63,348 J 16 20 26 K 44 59 77 Weight 2600 5500 11500 Workpiece weight max. kg 1000 2000 3000 Concentricity deviation 0,005 0,005 0,005 Speed max. min -1 7000 6000 4800 Spare live centres 1241762 1241763 1241764 Type 640-80 Heavy with draw-off nut especially for high load at high speeds body hardened and ground - tip angle 60 Item no. 304521 304522 304523 Mount MT 4 5 6 Size 484 485 486 A 122 150 180 B 70 95 120 D 32 42 58 G 31,267 44,399 63,348 J 16 20 26 K 44 59 77 M 100 125 155 Weight 2800 5400 12300 Workpiece weight max. kg 1000 2000 3000 Concentricity deviation 0,005 0,005 0,005 Speed max. min -1 7000 6000 4800 Spare live centres 1241762 1241763 1241764 2009

Revolving tailstock centres Heavy - heavy duty design Revolving tailstock centres MKS Type 604 Heavy - heavy duty design body hardened and ground - tip angle 60 Item no. 093439 466229 093440 058674 018801 093446 058675 466230 Mount 6 MK 7 Metr. 80 Metr. 100 (1:20) Metr. 120 (1:20) Nr. 80 (1:10) Nr. 100 (1:10) Nr. 120 (1:10) A 196 215 196 257 274 196 257 274 B 138 150 138 200 245 140 200 245 D 60 70 60 85 110 60 85 110 G 63,348 83,061 80 100 120 80 100 120 H 13 15 13 14 15 13 14 15 K 67 77 68 86 102 66 86 102 Workpiece weight max. kg 5000 9000 8500 13000 22000 8500 13000 22000 Concentricity deviation 0,01 0,01 0,015 0,02 0,015 0,01 0,01 0,01 Speed max. min -1 1500 1500 1500 1000 800 1500 1000 800 Heavy - heavy duty design Revolving tailstock centres for heavy duty machining. Perfectly suitable for turning and grinding machines. We have a lot of know-how and decades of experience in heavy duty machining. We offer highest concentricity deviation and best quality. Thanks to the lifetime lubrication our revolving tailstock centres are free of maintenance and ensure a very long life. Have we aroused your interest in revolving tailstock centres for heavy duty machining? Please contact us. We want you to receive exactly the right solution enabling you to achieve your goals in a reliable and economical manner. Type 652 Revolving tailstock centres for heavy duty machining with length compensation and pressure display. Type 604 MP Revolving tailstock centres for heavy duty machining with tailstock support. 2010

Revolving tailstock centres Speed - standard design Revolving tailstock centres MKS Type 663 Speed with draw-off nut - for especially high speeds, different head diameters at same size of shank body hardened and ground - tip angle 60 Item no. 340911 340910 338595 338594 344808 344809 Mount MT 4 4 5 5 6 6 Size 704/52 704/70 705/65 705/82 706/110 706/82 A 90 110 100 130 168 133 B 52 70 65 82 110 82 D 25 35 32 40 55 40 G 31,267 31,267 44,399 44,399 63,348 63,348 K 28 38 34 41 58 41 M 80 110 100 115 150 115 Weight 1900 2300 4000 5200 12000 8400 Workpiece weight max. kg 360 800 560 1250 2500 1250 Concentricity deviation 0,005 0,005 0,005 0,005 0,005 0,005 Speed max. min -1 15000 10000 12000 10000 7000 10000 Spare live centres 344924 344923 338895 338901 344925 338901 Speed - extended live centre Type 664 Speed extended NC-centre with carbide insert, for high speed body hardened and ground - tip angle 60 Item no. 772389 772390 772391 772392 Mount MT 2 3 4 5 Size 752 753 754 755 A 99 99 141 141 B 45 45 66 66 C 7 7 11 11 D 20 20 32 32 G 17,78 23,825 31,267 44,399 K 40 40 63 63 Weight 1200 1600 2600 5000 Workpiece weight max. kg 100 100 250 250 Concentricity deviation 0,01 0,01 0,01 0,01 Speed max. min -1 12000 12000 9000 9000 Spare live centres 790267 790267 790291 790291 2011

Revolving tailstock centres Slim - standard design Revolving tailstock centres MKS Type 600 Slim with small casing diameter body hardened and ground - tip angle 60 Item no. 005336 005429 005469 005490 005547 Mount MT 2 3 4 5 6 Size 02 04 08 10 14 A 62 62 75,5 106 143 B 32 34 42 58 80 D 15 15 20 30 42 G 17,78 23,825 31,267 44,399 63,348 K 18 18 25 34 49 Weight 300 400 1000 2600 7100 Workpiece weight max. kg 200 400 800 1600 3500 Concentricity deviation 0,005 0,005 0,005 0,01 0,02 Speed max. min -1 7000 7000 6300 4300 3000 Spare live centres 1241748 1241749 1241750 1241751 1241752 Slim - extended live centre Type 600-20 Slim with small casing diameter and extended live centre body hardened and ground - tip angle 60 2012 Item no. 362080 362081 362082 362083 362084 Mount MT 2 3 4 5 6 Size 02 04 08 10 14 A 73 74 88,5 119 164 B 32 34 42 58 80 D 15 15 20 30 42 G 17,78 23,825 31,267 44,399 63,348 K 29 30 38 49 70 J 10 11 13 14 18 Weight 320 460 1000 2600 7100 Workpiece weight max. kg 170 340 700 1400 3000 Concentricity deviation 0,008 0,008 0,008 0,01 0,02 Speed max. min -1 7000 7000 6300 4300 3000 Spare live centres 1241753 1241754 1241755 1241756 1241757

Revolving tailstock centres Slim - extended live centre Revolving tailstock centres MKS Type 600-20 Slim with small casing diameter and profiled centre point body hardened and ground - tip angle 60 Item no. 1241695 1243505 1243507 1243509 Mount MT 2 3 4 5 Size 02 04 08 10 A 73 74 88,5 119 B 32 34 42 58 D 15 15 20 30 G 17,78 23,825 31,267 44,399 K 29 30 38 49 P 6 8 10 12 R 12 16 20 26 Workpiece weight max. kg 50 100 150 180 Speed max. min -1 7000 7000 6300 4300 Spare live centres 1241758 1241759 1241760 1241761 2013

Revolving tailstock centres Control - standard design Revolving tailstock centres MKS Type 652 AC Control with pressure display and length compensation as counter centre with face drivers body hardened and ground - tip angle 60 Item no. 060798 060874 060906 060915 Mount MT 3 4 5 6 Size 503 504 505 506 A 105 123,5 160,5 202 B 64 72 95 120 D 25 32 40 52 G 23,825 31,267 44,399 63,348 K 31,5 39 49 59 Weight 2100 3500 8300 17000 Spring way 1) 1,6 2 1,8 2,7 Axial load max. 550 900 1500 2000 Workpiece weight max. kg 400 800 1600 3200 Concentricity deviation 0,01 0,01 0,01 0,015 Speed max. min -1 4000 3500 2500 1800 Spare live centres 009192 009205 009325 009413 1) at max. axial load Control - extended live centre Type 652-AC-VL Control with pressure display, length compensation and extended live centre as counter centre with face drivers body hardened and ground - tip angle 60 Item no. 079920 079921 079922 079923 Mount MT 3 4 5 6 Size 503 504 505 506 A 120 137,5 177,5 223 B 64 72 95 120 D 25 32 40 52 G 23,825 31,267 44,399 63,348 K 46,5 53 66 80 J 11 14 15 24 Weight 2200 3600 8400 17500 Spring way 1) 1,6 2 1,8 2,7 Axial load max. 550 900 1500 2000 Workpiece weight max. kg 260 550 1100 2500 Concentricity deviation 0,01 0,01 0,01 0,015 Speed max. min -1 4000 3500 2500 1800 Spare live centres 079924 079925 079926 079927 1) at max. axial load 2014

Revolving tailstock centres - for interchangeable inserts Flex Revolving tailstock centres MKS Type 614 Flex for interchangeable inserts body hardened and ground Item no. 061030 061031 061032 061038 061039 061040 Mount MT 2 3 3 4 5 6 Size 102 104 106 108 110 114 A 45 48 55 67 85 101 B 43 48,5 58,5 68,5 88,5 102,5 D 20 22 25 32 40 50 E 4 4,5 5 5 6 6 G 17,78 23,825 23,825 31,267 44,399 63,348 Concentricity deviation 0,01 0,01 0,01 0,01 0,01 0,015 Workpiece weight max. kg 40 130 150 250 650 900 Weight without inserts 440 750 1100 1900 4400 8600 Weight 900 1700 2200 3700 8000 - Spare live spindle 009836 009838 009843 009870 009872 009874 Flex - Interchangeable inserts Type 616 Interchangeable inserts 60 Item no. Size A D E F G 070725 102 16 7 5,2 18 20 070728 104 20 12 9,6 24 24 070731 106 24 12 9,6 24 27,5 070734 108 28 15 12 30 31,5 070737 110 38 22 18,5 35 43 070740 114 50 28 24 40 54 Type 616 Interchangeable inserts 75 Item no. Size A D E F G 070726 102 16 7 5,2 18 17 070729 104 20 12 9,6 24 19,5 070732 106 24 12 9,6 24 22,5 070735 108 28 15 12 30 25,5 070738 110 38 22 18,5 35 35 070741 114 50 28 24 40 44 Type 616 Interchangeable inserts 90 Item no. Size A D E F G 070727 102 16 7 5,2 18 14,5 070730 104 20 12 9,6 24 16,5 070733 106 24 12 9,6 24 19 070736 108 28 15 12 30 21,5 070739 110 38 22 18,5 35 29 070742 114 50 28 24 40 36 2015

Revolving tailstock centres - for interchangeable inserts Flex - Interchangeable inserts Revolving tailstock centres MKS Type 616 Interchangeable inserts 60 VL Item no. Size A D E F G J 070719 102 14 7 5,2 18 25 6 070720 104; 106 18 12 9,6 24 30 8 070721 108 26 15 12 30 43 12 070722 110 32 22 18,5 35 55 13 070723 114 42 28 24 40 70 18,5 Type 616 Interchangeable inserts for tubular workpieces 60 Item no. Size A D E F G J 070700 102 25 7 5,2 18 21 10 070701 104 35 12 9,6 24 26 15 070702 106 45 12 9,6 24 27 25 070703 108 55 15 12 30 31,5 30 070704 110 70 22 18,5 35 39 40 070705 114 100 28 24 40 52 55 Type 616 Interchangeable inserts A for centerless workpieces 60 Item no. Size A D E F G M N 070707 102 25 7 5,2 18 18 20 10 070708 104 35 12 9,6 24 24 30 15 070709 106 45 12 9,6 24 25 40 25 070710 108 55 15 12 30 30 48 30 070711 110 70 22 18,5 35 39 63 40 070712 114 100 28 24 40 52 90 55 Type 616 Interchangeable inserts B for centerless workpieces 60 Item no. Size A D E F G M N 228620 102 16 7 5,2 18 12 12 6 228621 106 22 12 9,6 24 16 18 10 228622 108 40 15 12 30 25 35 20 308632 110 52 22 18,5 35 30 45 30 Type 616 Extractor Item no. For size 061707 102 061708 104/106/108 061709 110/114 2016

Flex - assortment Revolving tailstock centres - for interchangeable inserts Revolving tailstock centres MKS Type 614-00 complete with all inserts in a sturdy wooden case Item no. 061702 061703 061704 061705 061706 Mount MT 2 3 3 4 5 Size 102 104 106 108 110 Workpiece weight max. kg 40 130 150 250 650 Weight 900 1700 2200 3700 8000 2017

Revolving centering tapers MZK Mitlaufende Zentrierkegel MZK Type 608-00 Revolving centering tapers Type 640-90 Revolving centering tapers with draw-off nut, for high load Item no. Size Mount MT A Workpiece weight max. kg Weight 304562 108 4 103 800 2200 304563 110 5 128 1600 4800 304564 114 6 159 3000 12000 Including fixing screw and washer, without insert Item no. Size Mount MT A Workpiece weight max. kg Weight 304583 494 4 118 1000 3200 304584 495 5 140 2000 6500 304585 496 6 168 3500 13500 Including fixing screw and washer, without insert Tool group A07 Type 698-00 Fixed shafts Item no. Mount MT A Workpiece weight max. kg Weight 304580 4 45 2000 800 304581 5 60 4800 2000 304582 6 70 12000 5500 Including fixing screw and washer, without insert Interchangeable inserts MZK Type 608-20 Suitable inserts for centering tapers AZ Standard version, taper 75 Type 608-40 Suitable inserts for centering tapers AZR with three support surfaces, for rough pieces 75 2018 Item no. Size for MT B C D E Weight 304565 1) 1 4 60 68 5 32 900 304566 2 4 100 45 45 32 1500 304567 3 4 150 45 95 32 4100 304568 4 4 200 45 145 32 6000 304569 5 4 250 45 195 32 8500 304570 1 5 100 43 45 40 1500 304571 2 5 150 43 95 40 4400 304572 3 5 200 43 145 40 6100 304573 4 5 250 43 195 40 8100 304574 5 5 300 43 245 40 11600 304575 1 6 150 54 95 50 3000 304576 2 6 200 54 145 50 8100 304577 3 6 250 54 195 50 11100 304578 4 6 300 54 245 50 14000 304579 5 6 350 54 295 50 18800 1) Without fixing by screw and washer Item no. Size for MT B C D E Weight 304736 2 4 100 45 45 32 1500 304737 3 4 150 45 95 32 4100 304738 4 4 200 45 145 32 6000 304739 5 4 250 45 195 32 8500 304740 1 5 100 43 45 40 1500 304741 2 5 150 43 95 40 4400 304742 3 5 200 43 145 40 6100 304743 4 5 250 43 195 40 8100 304744 5 5 300 43 245 40 11600 304745 1 6 150 54 95 50 3000 304746 2 6 200 54 145 50 8100 304747 3 6 250 54 195 50 11100 304748 4 6 300 54 245 50 14000 304749 5 6 350 54 295 50 18800

Revolving centering tapers MZK Type 627 Revolving centering taper, pointed as centering taper for tubular workpieces and as a revolving tailstock centre to machine normal workpieces Item no. Size Mount MT A B G Workpiece weight max. kg Concentricity Weight deviation 010613 272 2 61 42 17,78 200 0,01 400 010635 273 3 79 56 23,825 400 0,008 1100 010638 274 4 100 64 31,267 800 0,008 1600 010642 275 5 115,5 78 44,399 1600 0,008 3600 306396 276 6 153 105 63,348 2500 0,008 10000 Revolving centering tapers MZK Type 617 Revolving tailstock center, cone truncated, 60 Item no. Size Mount MT A B D E G Workpiece Concentricity Weight weight max. deviation kg 301615 171 1 64 50 20 52 12,065 100 0,008 900 301616 171a 2 65 50 20 52 17,78 200 0,008 1200 301556 172 2 77 80 30 64 17,78 300 0,008 2000 301557 172a 3 77 80 30 64 23,825 400 0,008 2200 221605 173 3 96,5 120 30 83 23,825 600 0,008 4200 301558 172b 4 78,5 80 30 64 31,267 400 0,008 2300 044023 173a 4 98 120 30 83 31,267 800 0,008 4500 090483 173b 5 99 120 30 83 44,399 800 0,008 5300 Type 618 Revolving tailstock center, cone truncated, 75 Item no. Size Mount MT A B D E G Workpiece weight max. kg Concentricity Weight deviation 301559 172 2 80 80 20 67 17,78 300 0,008 2000 301560 172a 3 80 80 20 67 23,825 400 0,008 2000 062211 173 3 85,5 120 30 72 23,825 600 0,008 4200 301561 172b 4 81,5 80 20 67 31,267 400 0,008 2400 062224 173a 4 87 120 30 72 31,267 800 0,008 4300 062299 174 4 107 170 50 90 31,267 1200 0,01 9700 062232 173b 5 88 120 30 72 44,399 800 0,008 5100 063614 174a 5 106 170 50 90 44,399 1600 0,01 10600 063662 175 5 146,5 250 75 130 44,399 2000 0,01 34000 063633 174b 6 107,5 170 50 90 63,348 1600 0,01 13300 063656 175a 6 148 250 75 130 63,348 2000 0,01 37000 063680 176 6 184 350 120 168 63,348 4000 0,015 82000 2019

Dead centres FKS Dead centres FKS Dead centres DIN 806 and DIN 807 completely hardened and ground (with carbide-tipped ground only). Different types available. Dead centres are manufactured with a concentricity of 5 micrometers. Versions with a concentricity of 3 micrometers or better are also available on request. Technical features: - completely hardened and ground - high concentricity - heavy duty Tool group A07 Type 665 DIN 806, full point material: tool steel Item no. Mount MT A B d1 l1 Weight 013706 0 9,2 70 9,045 20 30 013707 1 12,2 80 12,065 26,5 60 013709 2 18 100 17,78 36 150 013711 3 24,1 125 23,825 44 340 013712 4 31,6 160 31,267 57,5 760 013715 5 44,7 200 44,399 70,5 1920 013718 6 63,8 270 63,348 88 5200 Tool group A07 Type 667 DIN 806, full point, ground only carbide-tipped Item no. Mount MT A B D d1 l1 Weight 017169 0 9,2 70 5 9,045 20 30 017170 1 12,2 80 7 12,065 26,5 55 017171 2 18 100 7 17,78 36 155 017172 3 24,1 125 11 23,825 44 360 017173 4 31,6 160 14 31,267 57,5 770 017174 5 44,7 200 18 44,399 70,5 1950 017175 6 63,8 270 18 63,348 88 5200 Tool group A07 Type 677 DIN 806, full point, ground only carbide-tipped full point Item no. Mount MT A B d1 l1 Weight 326786 2 18 100 17,78 36 175 306402 3 24,1 125 23,825 44 400 221398 4 31,6 160 31,267 57,5 855 326816 5 44,7 200 44,399 70,5 2160 Tool group A07 Type 668 DIN 806, half point material: tool steel Item no. Mount MT A B E F d1 l1 Weight 013867 1 12,2 80 7,6 22 12,065 26,5 55 013868 2 18 100 11 30 17,78 36 145 013870 3 24,1 125 15 38 23,825 44 310 013871 4 31,6 160 21 50 31,267 57,5 710 013997 5 44,7 200 29,4 63 44,399 70,5 1925 013999 6 63,8 270 42 79 63,348 88 4800 2020

Dead centres FKS Tool group A07 Type 670 DIN 806, half point, ground only carbide-tipped Item no. Mount MT A B D E F d1 l1 Weight 027438 1 12,2 80 7 7,6 22 12,065 26,5 55 027439 2 18 100 7 11 30 17,78 36 150 027440 3 24,1 125 11 15 38 23,825 44 335 026571 4 31,6 160 14 21 50 31,267 57,5 750 027441 5 44,7 200 18 29,4 63 44,399 70,5 1830 Dead centres FKS Tool group A07 Type 671 similar DIN 807, full point with draw-off nut material: tool steel Item no. Mount MT A B C d1 l1 Key-width SW Weight 005361 1 12,2 90 M16x1,5 12,065 36,5 10 140 005553 2 18 112 M22x1,5 17,78 48 14 300 005654 3 24,1 138 M27x1,5 23,825 57 19 580 005357 4 31,6 175 M36x1,5 31,267 72,5 27 800 005381 5 44,7 217 M48x1,5 44,399 87,5 36 2900 005426 6 63,8 290 M68x1,5 63,348 108 55 7200 Tool group A07 Type 672 similar DIN 807, full point with draw-off nut, with extended point material: tool steel Item no. Mount MT A B C D d1 l1 Key-width SW Weight 249575 2 18 118 M22x1,5 10 17,78 54 14 300 249576 3 24,1 148 M27x1,5 10 23,825 67 19 600 249577 4 31,6 186,5 M36x1,5 14 31,267 84 27 1285 249578 5 44,7 242 M48x1,5 16 44,399 112 36 3000 249579 6 63,8 330 M68x1,5 20 63,348 148 55 7900 Tool group A07 Type 671 Draw-off nut Item no. C H Key-width SW Weight 005363 M16x1,5 12 24 26 005555 M22x1,5 15,5 32 55 005656 M27x1,5 17,5 41 110 005359 M36x1,5 21 55 240 005383 M48x1,5 23 75 480 005428 M68x1,5 25,5 100 900 Tool group A07 Type 673 full point with centre bore material: tool steel Item no. Mount MT A B D G d1 l1 Weight 015001 1 12,2 77 2,5 1 12,065 23,5 60 015003 2 18 95,5 4 1,6 17,78 31,5 170 015004 3 24,1 120 5 2 23,825 39 350 015005 4 31,6 153 6,5 2,5 31,267 50,5 800 015006 5 44,7 191 8 3,19 44,399 61,5 1900 2021

Dead centres FKS Dead centres FKS Tool group A07 Typ 674 half point with centre bore material: tool steel Item no. Mount MT A B D E F G d1 l1 Weight 015009 1 12,2 77 2,5 8,6 19 1 12,065 23,5 55 015010 2 18 95,5 4 12 26 1,6 17,78 31,5 150 015011 3 24,1 120 5 15,7 32 2 23,825 39 310 015022 4 31,6 153 6,5 20,8 42 2,5 31,267 50,5 705 015023 5 44,7 191 8 29,4 53 3,15 44,399 61,5 1800 Tool group A07 Type 695 DIN 806, full point with spanner flat material: tool steel Item no. Mount MT A B d1 l1 Key-width SW Weight 015028 1 12,2 80 12,065 26,5 10 55 015032 2 18 100 17,78 36 14 145 015039 3 24,1 125 23,825 44 19 340 015042 4 31,6 160 31,267 57,5 27 740 015040 5 44,7 200 44,399 70,5 36 1860 2022

Überblick Overview Constant Face Drivers CoE For efficient high-precision turning of workpieces along their whole length without rechucking. In the same operation there may be also milled a groove or toohting. This could save a retooling, i. e. to a vice, which may turn out to be both time and money saving. The modular principle design allows the unlimited exchange of driver discs and centres. The mechanical compensation system guarantees equal clamping forces even on uneven workpiece faces. The spring cushioned centre allows the axial stop at the face of the workpiece. Clamping diameter 8-80 mm Max. workpiece weight 100 kg Constant Face Drivers CoA For efficient high-precision turning of workpieces along their whole length without rechucking. The modular principle design allows the unlimited exchange of driver discs and centres. The hydraulic or mechanical compensation system guarantees equal clamping forces even on uneven workpiece faces. The spring cushioned centre allows the axial stop at the face of the workpiece. Clamping diameter 8-80 mm Max. workpiece weight 100 kg CoM With spring loaded centre, attachable driver disc and mechanical compensation system. Adaptor flange with disc spring package or basic body with morse taper. For the clamping of big and heavy workpieces. Clamping diameter 50-250 mm Max. workpiece weight 500 kg CoB For the clamping of big and heavy workpieces. Also for extremely uneven faces. Basic body with morse taper or adaptor flange with disc spring package. Different driver heads with interchangeable driver pins and hydraulic compensation system. Rigid and axial adjustable spring loaded centres. Max. workpiece weight: 500 kg With intensified disc spring package: 1000 kg CoK Power-operated Face driver. For machining workpieces which are highly unbalanced, very heavy, for high chip removal or for irregular cutting, e.g. square billets, forged gear components etc. High precision concentricity by virtue of the solid centre even in permanent hard use. Longitudinal workpiece stop provided in centering. Precise tripping to workpiece centre, particularly advantageous for consecutive machining, e.g. plunge-cut grinding etc. CoK Type 690-00: Clamping-Ø 8-80 mm mechanical compensation, slip-on driving discs CoK Typ 690-50: Clamping-Ø 50-250 mm mechanical compensation, slip-on driving discs CoK Driving heads Type 689: Clamping-Ø 63-160 mm hydraulic compensation, interchangeable driving pins 2023

Constant Face Drivers CoE For rational turning of workpieces on their entire length without reclamping with high precision. Accessories Face Drivers CoE Developed according to the modular system, therefore universal exchange of driving discs and centres possible. One set consists of one basic body, one driving disc and suitable centre. Easy to maintain Technical features: - mechanic pressure compensation provides a uniform clamping force also on uneven faces of workpieces - the spring loaded centre provides a longitudinal workpiece stop on the front side - workpiece weight max. 100 kg - Clamping circuit Ø 8-80 mm - approx. value for an axially admitted total load of the 3 supporting pistons: 900 dan Customer advantage: - face driver for turning and milling - compensating driving plates with radial freedom of movement - easy mechanical compensation of the driving plates - stable and consistent length stop - high concentricity Visit our new YouTube channel and take a look at the product video CoE. Type 684-90 Basic body CoE with morsetaper (all basic bodies without centre) mechanical Item no. MT A B H Z Stroke Centres Weight 310065 3 62 65 max. 38 min. 26 16 10 1800 310066 4 62 65 max. 38 min. 26 16 10 1900 310068 5 62 65 max. 38 min. 26 16 10 2000 1) Mounting with short taper and centering diameter on request Accessories CoE Type 684-30 Driving discs, toothed right- and left-hand rotation, free from play Item no. Clamping circuit Ø S Approx. turning range I R V Matching center point Ø Y 1209000 8 9-16 4,5 38 4 4 120 1209001 10 11-20 4,5 38 4 4 120 1209002 12 13-24 7 36 4 6 120 1209003 16 17-32 11 33 4 10 120 1209004 20 21-40 13 30 4 12 120 1209005 25 26-50 17 30 8 16 130 1209006 32 33-64 22 30 10 16 160 Driving discs with carbide toothing on request Weight Type 684-31 Driving discs, with interchangeable hard metal driving plates 6 x 3,2 right- and left-hand rotation Item no. Clamping circuit Ø S Approx. turning range I R V Matching center point Ø Y 1209007 20 21-40 7 30 8 6 125 1209008 25 26-50 11 30 8 10 140 1209009 32 33-64 17,5 30 10 16 160 1209010 40 41-80 27 30 16 16 180 Weight 2024

Constant Face Drivers Accessories CoE Type 684-31 Driving discs, with interchangeable hard metal driving plates 6 x 3,2 which can be used on 4 sides right- and left-hand rotation, free from play Item no. Clamping circuit Ø S Approx. turning range I R Matching center point Ø Y 1209011 50 51-100 36 30 16 260 1209012 63 64-126 49 30 16 420 1209013 80 81-160 66 30 16 680 Weight Constant Face Drivers CoE Type 684-40 Centres, CoE Item no. Clamping circuit Ø N Y Z Weight 1209016 8-10 90 4 16 110 1209017 12 90 6 16 110 1209018 16 90 10 16 110 1209019 20 90 12 16 110 1209020 25-80 90 16 16 120 Centres with head on request Type 680-93 Hard metal driving plates right- and left-hand rotation Item no. Size Clamping circuit Ø Weight 088970 6x3,2 20-32 2 Type 680-72 Mounting sleeve for the clamping of a face driver in lathe chuck A G B Item no. MT inside A B C D G Weight 085033 3 31 39 32 40 23,825 150 085034 4 39 47 42 50 31,267 250 085035 5 54 62 52 60 44,399 480 C D CoE - Assortments Type 684-31 CoE-Small assortment in wooden box mechanical, clamping dia. 12-50 mm, turning range 13-100 mm Included in delivery: 1x Basic body 4x Driving discs (clamping-ø 12, 20, 32, 50) 3x Centres (center-ø 6, 12, 16) Item no. MT Weight 1209048 3 3600 1209049 4 3870 1209050 5 4550 2025

Constant Face Drivers CoA Constant Face Drivers CoA For rational turning of workpieces on their entire length without reclamping with high precision. Developed according to the modular system, therefore universal exchange of driving discs and centres possible. One set consists of one basic body, one driving disc and suitable centre. Technical features: - hydraulic pressure compensation provides a uniform clamping force also on uneven faces of workpieces - the spring loaded centre provides a longitudinal workpiece stop on the front side - workpiece weight max. 100 kg - approx. value for an axially admitted total load of the 3 supporting pistons: 2000 dan Type 680-50 Basic body with morsetaper (basic bodies without centre) CoA hydraulic Item no. MT A B H Z Stroke Centres Weight 088173 3 70 54 max. 45 min. 26 16 10 1600 088174 4 70 56,5 max. 45 min. 26 16 15 1800 088175 5 70 56,5 max. 45 min. 26 16 15 2800 088176 6 70 56,5 max. 45 min. 26 16 15 4400 For rational turning of workpieces on their entire length without reclamping with high precision. Developed according to the modular system, therefore universal exchange of driving discs and centres possible. One set consists of one basic body, one driving disc and suitable centre. Technical features: - hydraulic pressure compensation provides a uniform clamping force also on uneven faces of workpieces - the spring loaded centre provides a longitudinal workpiece stop on the front side - workpiece weight max. 100 kg - approx. value for an axially admitted total load of the 3 supporting pistons: 2000 dan Type 680-55 Basic body with morsetaper, with draw-offnut, CoA hydraulic Item no. MT A B H Z Stroke Centres Weight 088177 3 70 54 max. 45 min. 26 16 10 1800 088178 4 70 56,5 max. 45 min. 26 16 15 2200 088179 5 70 56,5 max. 45 min. 26 16 15 3000 088180 6 70 56,5 max. 45 min. 26 16 15 4600 For rational turning of workpieces on their entire length without reclamping with high precision. For clamping in lathe chucks with unstepped jaws Developed according to the modular system, therefore universal exchange of driving discs and centres possible. One set consists of one basic body, one driving disc and suitable centre. Technical features: - hydraulical respectively mechanical pressure compensation provides a uniform clamping force also on uneven faces of workpieces - the spring loaded centre provides a longitudinal workpiece stop on the front side - workpiece weight max. 100 kg Type 680-65 Basic body for clamping in lathe chucks, with springset, CoA mechanical / hydraulic Item no. A B G H M Z Stroke Centres Weight 088074 1) 85 45 25 max. 45 min. 26 110 16 15 2300 313085 2) 85 45 25 max. 45 min. 26 110 16 15 2300 1) with hydraulic compensation 2) with mechanical compensation 2026

Constant face drivers CoA For rational turning of workpieces on their entire length without reclamping with high precision. Developed according to the modular system, therefore universal exchange of driving discs and centres possible. One set consists of one basic body, one driving disc and suitable centre. Technical features: - mechanic pressure compensation provides a uniform clamping force also on uneven faces of workpieces - the spring loaded centre provides a longitudinal workpiece stop on the front side - workpiece weight max. 100 kg Constant Face Drivers CoA Type 681-85 Basic body with short taper ISO 702-1 (DIN 55026) mechanical compensation, with spring set, CoA mechanical Item no. Taper A B E F G H K M O P T Z Stroke Centres 313905 5 133 - M 10 15 25 max. 45 min. 26 82,563 32 90 86 104,8 16 11 6500 313906 6 165 35 M 12 18 25 max. 45 min. 26 106,375 32 90 86 133,4 16 11 7000 313907 8 210 40 M 16 23 25 max. 45 min. 26 139,719 32 90 86 171,4 16 11 8100 Weight For rational turning of workpieces on their entire length without reclamping with high precision. Developed according to the modular system, therefore universal exchange of driving discs and centres possible. One set consists of one basic body, one driving disc and suitable centre. Technical features: - hydraulical respectively mechanical pressure compensation provides a uniform clamping force also on uneven faces of workpieces - the spring loaded centre provides a longitudinal workpiece stop on the front side - workpiece weight max. 100 kg Type 680-60 Basic body flange type, with springset, CoA mechanical / hydraulic Item no. A B D E F G H M O P T Z Stroke Centres 088046 1) 142 30 100 M 10 15 25 max. 45 min. 26 61 90 98 120 16 15 7300 313910 2) 142 30 100 M 10 15 25 max. 45 min. 26 61 90 98 120 16 15 7300 1) with hydraulic compensation 2) with mechanical compensation Weight 2027

Constant Face Drivers Adapter plate CoA Constant Face Drivers CoA Type 688-87 Adapter plate short taper without spring set Item no. Design Taper A B D I K Weight 088485 DIN 55026 5 140 30 100 38 82,563 3100 088486 DIN 55026 6 167 35 100 38 106,39 4800 088487 DIN 55026 8 216 40 100 38 139,735 8700 088488 DIN 55026 11 280 45 100 38 196,885 17000 088480 DIN 55027 5 140 30 100 38 82,563 3100 088481 DIN 55027 6 167 35 100 38 106,39 4800 088482 DIN 55027 8 216 40 100 38 139,735 8700 088483 DIN 55027 11 280 45 100 38 196,885 17000 088495 DIN 55029 5 140 30 100 38 82,563 3100 088496 DIN 55029 6 167 35 100 38 106,39 4800 088497 DIN 55029 8 216 40 100 38 139,735 8700 088498 DIN 55029 11 280 45 100 38 196,885 17000 2028

Constant Face Drivers Accessories CoA Type 680-10 Driving discs, toothed right-hand rotation Item no. Clamping circuit Ø S Approx. I R V Matching center Weight turning range point Ø Y 088061 8 9-16 4,5 38 4 4 120 088062 10 11-20 4,5 38 4 4 120 088063 12 13-24 7 36 4 6 120 088064 16 17-32 11 33 4 10 120 088065 20 21-40 13 30 4 12 120 088066 25 26-50 17 30 8 16 150 088067 32 33-64 22 30 10 16 190 Driving discs with carbide toothing, friction lining or diamant granulation on request Accessories Face Drivers CoA Type 680-20 Driving discs, toothed left-hand rotation Item no. Clamping circuit Ø S Approx. turning range I R V Matching center point Ø Y 088081 8 9-16 4,5 38 4 4 120 088082 10 11-20 4,5 38 4 4 120 088083 12 13-24 7 36 4 6 120 088084 16 17-32 11 33 4 10 120 088085 20 21-40 13 30 4 12 120 088086 25 26-50 17 30 8 16 150 088087 32 33-64 22 30 10 16 190 Driving discs with carbide toothing on request Weight Type 680-30 Driving discs, toothed right- and left-hand rotation Item no. Clamping circuit Ø S Approx. turning range I R V Matching center point Ø Y 088541 8 9-16 4,5 38 4 4 120 088542 10 11-20 4,5 38 4 4 120 088543 12 13-24 7 36 4 6 120 088544 16 17-32 11 33 4 10 120 Driving discs with carbide toothing on request Weight Type 680-11 Driving discs, with interchangeable hard metal driving plates 6 x 3,2 right-hand rotation Item no. Clamping circuit Ø S Approx. turning range I R V Matching center point Ø Y Weight 089065 20 H 21-40 7 30 5 6 125 089066 25 H 26-50 11 30 8 10 140 089067 32 H 33-64 17,5 30 10 16 200 2029

Constant Face Drivers Accessories CoA Accessories Face Drivers CoA Type 680-21 Driving discs, with interchangeable hard metal driving plates 6 x 3,2 left-hand rotation Item no. Clamping circuit Ø S Approx. turning range I R V Matching center point Ø Y 089085 20 H 21-40 7 30 5 6 125 089086 25 H 26-50 11 30 8 10 140 089087 32 H 33-64 17,5 30 10 16 200 Weight Type 680-31 Driving discs, with interchangeable hard metal driving plates 6 x 3,2 right- and left-hand rotation Item no. Clamping circuit Ø S Approx. turning range I R V Matching center point Ø Y 088545 20 H 21-40 7 30 5 6 125 088546 25 H 26-50 11 30 8 10 140 088547 32 H 33-64 17,5 30 10 16 200 Weight Type 680-12 Driving discs, with interchangeable hard metal driving plates 6 x 3,2 which can be used on 4 sides right-hand rotation Item no. Clamping circuit Ø S Approx. turning range H C Matching center point Ø Y 088068 40 41-80 20 24 16 200 088069 50 51-100 28 24 16 240 088070 63 64-126 41 24 16 400 088071 80 81-160 58 24 16 600 Weight Type 680-22 Driving discs, with interchangeable hard metal driving plates 6 x 3,2 which can be used on 4 sides left-hand rotation Item no. Clamping circuit Ø S Approx. turning range H C Matching center point Ø Y Weight 088088 40 41-80 20 24 16 200 088089 50 51-100 28 24 16 240 088090 63 64-126 41 24 16 400 088091 80 81-160 58 24 16 600 2030

Constant Face Drivers Accessories CoA Type 680-32 Driving discs, with interchangeable hard metal driving plates 6 x 3,2 which can be used on 4 sides right- and left-hand rotation Item no. Clamping circuit Ø S Approx. turning range H C Matching center point Ø Y 088548 40 41-80 20 24 16 200 088549 50 51-100 28 24 16 240 088550 63 64-126 41 24 16 400 088551 80 81-160 58 24 16 600 Weight Accessories Face Drivers CoA Type 680-40 Centres, CoA Item no. Clamping circuit Ø N Y Z Weight 088351 8-10 90 4 16 110 088352 12 90 6 16 110 088353 16 90 10 16 110 088354 20 90 12 16 110 088355 25-80 90 16 16 120 086758 25-80 110 16 16 150 Type 680-45, Centres with head, CoA Item no. Taper Ø N Z Weight A Y 086619 21 10 90 16 136 086620 27 16 90 16 153 688878 34 23 90 16 190 086621 40 29 90 16 210 688880 48 37 90 16 250 086622 56 45 90 16 312 Type 680-90 Hard metal driving plates right- or left-hand rotation Item no. Size Clamping circuit Ø Weight 088810 6x3,2 20-32 2 088209 9,5x3,2 40-80 4 088209 088810 Type 680-93 Hard metal driving plates right- and left-hand rotation Item no. Size Clamping circuit Ø Weight 088970 6x3,2 20-32 2 087931 9,5x3,2 40-80 4 Type 680-72 Mounting sleeve for the clamping of a face driver in lathe chuck A G B Item no. MT inside A B C D G Weight 085033 3 31 39 32 40 23,825 150 085034 4 39 47 42 50 31,267 250 085035 5 54 62 52 60 44,399 480 085036 6 75 83 62 70 63,448 1050 C D 2031

Constant Face Drivers Accessories CoA Accessories Face Drivers CoA Tool group C15 Type 0167-Y Threaded pin 088205 Item no. Size Clamping circuit Ø Weight 234695 M 4 x 6 20 1 048205 M 5 x 8 25+32 1 088205 M 5 x 8 40-80 2 Tool group C15 Type 5191-Y O-ring Item no. Size 006252 21,82x3,53 Type 680 RÖHM slide rule to calculate axial tailstock loading Item no. 088230 35 Weight 2032

Constant Face Drivers CoA - Assortments Type 680 Basic equipment in a carton hydraulic, clamping dia. 12 + 32 mm, turning range 13-64 mm Item no. MT right-hand rotation left-hand rotation with draw-off nut Weight 088553 3 2100 088557 3 2400 088573 3 2100 088577 3 2400 088554 4 2400 088558 4 2700 088574 4 2400 088578 4 2700 088555 5 3300 088559 5 3600 088575 5 3300 088579 5 3600 088556 6 4900 088560 6 5200 088576 6 4900 088580 6 5200 Constant Face Drivers CoA Type 680 Small assortment in wooden box hydraulic, clamping dia. 12-50 mm, turning range 13-100 mm Item no. MT right-hand rotation left-hand rotation with draw-off nut Weight 088501 3 3900 088511 3 4200 088521 3 3900 088531 3 4200 088502 4 4300 088512 4 4600 088522 4 4300 088532 4 4600 088503 5 4900 088513 5 5200 088523 5 4900 088533 5 5200 088504 6 6600 088514 6 6800 088524 6 6600 088534 6 6800 Type 680 Large assortment in wooden box hydraulic, clamping dia. 10-80 mm, turning range 11-160 mm Item no. MT right-hand rotation left-hand rotation with draw-off nut Weight 088218 3 5600 088223 3 5600 088233 3 5900 088238 3 5900 088219 4 6000 088224 4 6000 088234 4 6300 088239 4 6300 088220 5 6600 088225 5 6600 088235 5 6900 088240 5 6900 088221 6 8300 088226 6 8300 088236 6 8500 088241 6 8500 2033

Constant Face Drivers CoM Constant Face Drivers CoM Type 688 Basic body with morse taper and draw-off nut mechanical / hydraulic Item no. MT A B D E T Weight 088295 5 140 45 100 M 10 120 5800 088296 6 140 45 100 M 10 120 7480 Adapter plate CoM Type 688 Adapter plate short taper with spring set Item no. Taper Design A B D E G K M T Weight 088331 5 DIN 55026 140 30 100 M 10 37,5 82,563 144 120 4500 088332 6 DIN 55026 165 35 100 M 10 37,5 106,39 139 120 7000 088333 8 DIN 55026 216 40 100 M 10 37,5 139,735 134 120 11500 088334 11 DIN 55026 280 45 100 M 10 37,5 196,885 129 120 23000 088335 5 DIN 55027 140 30 100 M 10 37,5 82,563 144 120 5500 088336 6 DIN 55027 165 35 100 M 10 37,5 106,39 139 120 7000 088337 8 DIN 55027 216 40 100 M 10 37,5 139,735 134 120 11500 088338 11 DIN 55027 280 45 100 M 10 37,5 196,885 129 120 23000 088339 5 DIN 55029 140 30 100 M 10 37,5 82,563 144 120 4500 088340 6 DIN 55029 165 35 100 M 10 37,5 106,39 139 120 7000 088341 8 DIN 55029 216 40 100 M 10 37,5 139,735 134 120 11500 088342 11 DIN 55029 280 45 100 M 10 37,5 196,885 129 120 23000 2034

Constant Face Drivers Driving head CoM For clamping large and heavy workpieces, even with extremely uneven faces. O Driving discs CoM R R R R R Type 687-13 Driving discs with interchangeable hard metal driving plates right-hand rotation Item no. Clamping circuit Ø S R Hard metal driving plate Weight 689461 50 48 6 x 5T 1400 689462 63 45 6 x 5T 1500 689463 80 38 6 x 5T 1500 689464 100 38 6 x 5T 1400 689465 125 38 12 x 5T 1800 689466 160 38 12 x 5T 2500 689467 1) 200 38 12 x 5T 2500 689468 1) 250 38 12 x 5T 3200 1) Weight reduced R R R R R R R R S S S S S S S S S S S S S S S S FD U 60 o H A E T Z Technical features: - spring loaded, rigid centre, axially adjustable - basic body with morse taper or adapter plate with cup spring set - workpiece weight max. 500 kg - slip-on driving discs - clamping diameter 50-250 mm - mechanical compensation Constant Face Drivers CoM L R Type 687 Face driving head with cylindrical centre mount mechanical Item no. A D E F H L O R T U Z Weight 689080 142 100 M 10 15 35 102 128 38 120 120 32 7400 R R R Type 687-23 Driving discs with interchangeable hard metal driving plates left-hand rotation Item no. Clamping circuit Ø S R Hard metal driving plate Weight 689091 50 48 6 x 5T 1400 689092 63 45 6 x 5T 1500 689093 80 38 6 x 5T 1500 689094 100 38 6 x 5T 1400 689095 125 38 12 x 5T 1800 689096 160 38 12 x 5T 2500 689097 1) 200 38 12 x 5T 2500 689098 1) 250 38 12 x 5T 3200 1) Weight reduced 2035

Constant Face Drivers Accessories CoM Accessories Face Drivers CoM Type 688-40 Centres Item no. N Z Weight 088292 120 32 620 088293 140 32 750 Type 680-90 Hard metal driving plates right- or left-hand rotation Item no. Size Weight 312675 6 x 5 T 3 312911 12 x 5 T 6 Tool group C15 Type 0167-Y Threaded pin Item no. Size Weight 048205 M 5 x 8 1 036461 M 5 x 10 1 Tool group C15 Type 5191-Y O-ring Item no. Size 006283 59,69x5,33 2036

Constant Face Drivers CoB Constant Face Drivers CoB Type 688 Basic body with morse taper and draw-off nut mechanical / hydraulic Item no. MT A B D E T Weight 088295 5 140 45 100 M 10 120 5800 088296 6 140 45 100 M 10 120 7480 Adapter plate CoB Type 688 Adapter plate short taper with spring set Item no. Taper Design A B D E G K M T Weight 088331 5 DIN 55026 140 30 100 M 10 37,5 82,563 144 120 4500 088332 6 DIN 55026 165 35 100 M 10 37,5 106,39 139 120 7000 088333 8 DIN 55026 216 40 100 M 10 37,5 139,735 134 120 11500 088334 11 DIN 55026 280 45 100 M 10 37,5 196,885 129 120 23000 088335 5 DIN 55027 140 30 100 M 10 37,5 82,563 144 120 5500 088336 6 DIN 55027 165 35 100 M 10 37,5 106,39 139 120 7000 088337 8 DIN 55027 216 40 100 M 10 37,5 139,735 134 120 11500 088338 11 DIN 55027 280 45 100 M 10 37,5 196,885 129 120 23000 088339 5 DIN 55029 140 30 100 M 10 37,5 82,563 144 120 4500 088340 6 DIN 55029 165 35 100 M 10 37,5 106,39 139 120 7000 088341 8 DIN 55029 216 40 100 M 10 37,5 139,735 134 120 11500 088342 11 DIN 55029 280 45 100 M 10 37,5 196,885 129 120 23000 2037

Constant Face Drivers Driving heads CoB Constant Face Drivers CoB 5 For clamping large and heavy workpieces, even with extremely uneven faces. With hydraulic compensation - interchangeable driving pins Workpiece weight with single layer disc spring package: 500 kg Workpiece weight with double layer disc spring package: 1000 kg Technical features: - bolt-on face driver heads with interchangeable driving pins - driving pins can be changed to allow right-hand or left-hand rotation - spring loaded, rigid centre, axially adjustable Type 688-10 Face Driving Head size 1 CoB; hydraulic right-hand rotation Item no. S Approx. turning range A C D E F H L O T V Z Pin Weight 088301 63 65-125 142 6 100 M 10 15 max. 45 min. 18 102 72 120 16 25 6 x 16 A 7000 088361 75 80-150 142 9,5 100 M 10 15 max. 45 min. 18 102 72 120 16 25 6 x 16 H 7000 088302 80 82-160 142 14,5 100 M 10 15 max. 45 min. 18 102 72 120 16 25 6 x 16 C 7000 5 For clamping large and heavy workpieces, even with extremely uneven faces. With hydraulic compensation - interchangeable driving pins Workpiece weight with single layer disc spring package: 500 kg Workpiece weight with double layer disc spring package: 1000 kg Technical features: - bolt-on face driver heads with interchangeable driving pins - driving pins can be changed to allow right-hand or left-hand rotation - spring loaded, rigid centre, axially adjustable Type 688-10 Face Driving Head size 2 CoB; hydraulic right-hand rotation Item no. S Approx. turning range A C D E F H L O T V Z Pin Weight 088303 83 85-165 142 6 100 M 10 15 max. 45 min. 18 102 92 120 16 32 6 x 16 A 8200 088362 95 100-190 142 9,5 100 M 10 15 max. 45 min. 18 102 92 120 16 32 6 x 16 H 8200 088304 100 102-200 142 14,5 100 M 10 15 max. 45 min. 18 102 92 120 16 32 6 x 16 C 8200 2038

Constant Face Drivers Driving heads CoB 5 For clamping large and heavy workpieces, even with extremely uneven faces. With hydraulic compensation - interchangeable driving pins Workpiece weight with single layer disc spring package: 500 kg Workpiece weight with double layer disc spring package: 1000 kg Technical features: - bolt-on face driver heads with interchangeable driving pins - driving pins can be changed to allow right-hand or left-hand rotation - spring loaded, rigid centre, axially adjustable Constant Face Drivers CoB Type 688-10 Face Driving Head size 3 CoB; hydraulic right-hand rotation Item no. S Approx. turning range A C D E F H L O T V Z Pin Weight 088305 108 110-215 142 6 100 M 10 15 max. 45 min. 18 102 117 120 16 32 6 x 16 A 9500 088363 120 125-240 142 9,5 100 M 10 15 max. 45 min. 18 102 117 120 16 32 6 x 16 H 9500 088306 125 127-250 142 14,5 100 M 10 15 max. 45 min. 18 102 117 120 16 32 6 x 16 C 9500 5 For clamping large and heavy workpieces, even with extremely uneven faces. With hydraulic compensation - interchangeable driving pins Workpiece weight with single layer disc spring package: 500 kg Workpiece weight with double layer disc spring package: 1000 kg Technical features: - bolt-on face driver heads with interchangeable driving pins - driving pins can be changed to allow right-hand or left-hand rotation - spring loaded, rigid centre, axially adjustable Type 688-10 Face Driving Head size 4 CoB; hydraulic right-hand rotation Item no. S Approx. turning range A C D E F H L O T V Z Pin Weight 088307 143 145-285 182 6 100 M 10 15 max. 45 min. 18 102 152 120 16 32 6 x 16 A 16000 088364 155 160-310 182 9,5 100 M 10 15 max. 45 min. 18 102 152 120 16 32 6 x 16 H 16000 088308 160 162-320 182 14,5 100 M 10 15 max. 45 min. 18 102 152 120 16 32 6 x 16 C 16000 2039

Constant Face Drivers Driving heads CoB Constant Face Drivers CoB 5 For clamping large and heavy workpieces, even with extremely uneven faces. With hydraulic compensation - interchangeable driving pins Workpiece weight with single layer disc spring package: 500 kg Workpiece weight with double layer disc spring package: 1000 kg Technical features: - bolt-on face driver heads with interchangeable driving pins - driving pins can be changed to allow right-hand or left-hand rotation - spring loaded, rigid centre, axially adjustable Type 688-20 Face Driving Head size 1 CoB; hydraulic left-hand rotation Item no. S Approx. turning range A C D E F H L O T V Z Pin Weight 088321 63 65-125 142 6 100 M 10 15 max. 45 min. 18 102 72 120 16 25 6 x 16 A 7000 088381 75 80-150 142 9,5 100 M 10 15 max. 45 min. 18 102 72 120 16 25 6 x 16 H 7000 088322 80 82-160 142 14,5 100 M 10 15 max. 45 min. 18 102 72 120 16 25 6 x 16 C 7000 5 For clamping large and heavy workpieces, even with extremely uneven faces. With hydraulic compensation - interchangeable driving pins Workpiece weight with single layer disc spring package: 500 kg Workpiece weight with double layer disc spring package: 1000 kg Technical features: - bolt-on face driver heads with interchangeable driving pins - driving pins can be changed to allow right-hand or left-hand rotation - spring loaded, rigid centre, axially adjustable Type 688-20 Face Driving Head size 2 CoB; hydraulic left-hand rotation Item no. S Approx. turning range A C D E F H L O T V Z Pin Weight 088323 83 85-165 142 6 100 M 10 15 max. 45 min. 18 102 92 120 16 32 6 x 16 A 8200 088382 95 100-190 142 9,5 100 M 10 15 max. 45 min. 18 102 92 120 16 32 6 x 16 H 8200 088324 100 102-200 142 14,5 100 M 10 15 max. 45 min. 18 102 92 120 16 32 6 x 16 C 8200 2040

Constant Face Drivers Driving heads CoB 5 For clamping large and heavy workpieces, even with extremely uneven faces. With hydraulic compensation - interchangeable driving pins Workpiece weight with single layer disc spring package: 500 kg Workpiece weight with double layer disc spring package: 1000 kg Technical features: - bolt-on face driver heads with interchangeable driving pins - driving pins can be changed to allow right-hand or left-hand rotation - spring loaded, rigid centre, axially adjustable Constant Face Drivers CoB Type 688-20 Face Driving Head size 3 CoB; hydraulic left-hand rotation Item no. S Approx. turning range A C D E F H L O T V Z Pin Weight 088325 108 110-215 142 6 100 M 10 15 max. 45 min. 18 102 117 120 16 32 6 x 16 A 9500 088383 120 125-240 142 9,5 100 M 10 15 max. 45 min. 18 102 117 120 16 32 6 x 16 H 9500 088326 125 127-250 142 14,5 100 M 10 15 max. 45 min. 18 102 117 120 16 32 6 x 16 C 9500 5 For clamping large and heavy workpieces, even with extremely uneven faces. With hydraulic compensation - interchangeable driving pins Workpiece weight with single layer disc spring package: 500 kg Workpiece weight with double layer disc spring package: 1000 kg Technical features: - bolt-on face driver heads with interchangeable driving pins - driving pins can be changed to allow right-hand or left-hand rotation - spring loaded, rigid centre, axially adjustable Type 688-20 Face Driving Head size 4 CoB; hydraulic left-hand rotation Item no. S Approx. turning range A C D E F H L O T V Z Pin Weight 088327 143 145-285 182 6 100 M 10 15 max. 45 min. 18 102 152 120 16 32 6 x 16 A 16000 088384 155 160-310 182 9,5 100 M 10 15 max. 45 min. 18 102 152 120 16 32 6 x 16 H 16000 088328 160 162-320 182 14,5 100 M 10 15 max. 45 min. 18 102 152 120 16 32 6 x 16 C 16000 2041

Constant Face Drivers Accessories CoB Accessories Face Drivers CoB Type 688-40 Centres Tool group C15 Type 689-91 driving pins, right-hand rotation 16 A 16 H 16 C Item no. N Z Weight 088291 120 25 390 088292 120 32 620 088293 140 32 750 Item no. Diameter Size C Length Weight 085383 16 16 A 6 60 80 088100 16 16 H 9,5 60 90 085052 16 16 C 14,5 60 85 Tool group C15 Type 689-92 driving pins, left-hand rotation 16 A 16 H 16 C Item no. Diameter Size C Length Weight 085016 16 16 A 6 60 80 088099 16 16 H 9,5 60 90 085051 16 16 C 14,5 60 85 Type 680-90 Hard metal driving plates right- or left-hand rotation Item no. Size Clamping circuit Ø Weight 088209 9,5x3,2 40-80 4 Type 688-89 Sleeve with spring set, suitable for adapter plates Item no. Workpiece weight max. kg Weight 086806 500 800 087286 1000 800 2042

CoK Power-operated Face Drivers Power operated Face Driver CoK Particularly suitable for turning, copying and transfer machines with automatic infeed. Can also be used for milling and plain grinding machines by virtue of the solid centre. For machining workpieces which are highly unbalanced, very heavy, and require substantial removal of material or irregular cutting, e.g. square billets, forged gear components, etc. Constant Face Drivers CoK CoK Type 690-00 Clamping dia. 8-80 mm mechanical compensation, slip-on driving discs CoK Type 690-50 Clamping dia. 50-250 mm mechanical compensation, slip-on driving discs Cok Type 689 driving heads Clamping dia. 63-160 mm hydraulic compensation, with interchangeable driving pins Longitudinal workpiece stop provided in centering. Precise tripping to workpiece centre, particularly advantageous for consecutive machining, e.g. plunge-cut grinding, etc. High precision concentricity by virtue of the solid centre even with continuous hard use. Minimal centering power even with maximum cutting load. Drivers are pressed against the workpiece by poweroperated means. Uniformed loading of the mechanically or hydraulically equalising drivers. No change in the longitudinal workpiece stop through regrinding of the driving cutters. Optimum cutter run-in during opposed copy-turning through bevelled driving heads. All wearing parts are rapidly and easily replaced. The choice of clamping cylinder required depends upon the machine and workpiece conditions. As a rule size 105 suffices with the hydraulic actuating cylinders, size 150 with the pneumatic actuating cylinders. 2043

CoK 8-80 mm Power-operated Face Drivers Power-operated Face Drivers CoK High precision concentricity due to fixed centre point. Driving discs are pressed against the workpiece by power operated means. Clamping circuit Ø 8-80 mm Mechanically compensated Longitudinal workpiece stop in the centre Technical features: - high precision concentricity due to fixed centre point also under hard continuous operating conditions - minimal centering power even with maximum cutting load - workpiece weight max. 350 kg - slip-on driving discs, solid centre Tool group C15 Type 690-00 basic body (without centre, without draw-off nut) CoK mechanical Item no. A B D E F G O P T Z Stroke Centres Weight 313900 142 30 100 M 10 15 25 90 93 120 15 5 6500 Draw-off nut M 14x1,5 item-no. 089229 Adapter plate CoK Type 688-87 Adapter plate short taper without spring set Item no. Design Taper A B D I K Weight 088485 DIN 55026 5 140 30 100 38 82,563 3100 088486 DIN 55026 6 167 35 100 38 106,39 4800 088487 DIN 55026 8 216 40 100 38 139,735 8700 088488 DIN 55026 11 280 45 100 38 196,885 17000 088480 DIN 55027 5 140 30 100 38 82,563 3100 088481 DIN 55027 6 167 35 100 38 106,39 4800 088482 DIN 55027 8 216 40 100 38 139,735 8700 088483 DIN 55027 11 280 45 100 38 196,885 17000 088495 DIN 55029 5 140 30 100 38 82,563 3100 088496 DIN 55029 6 167 35 100 38 106,39 4800 088497 DIN 55029 8 216 40 100 38 139,735 8700 088498 DIN 55029 11 280 45 100 38 196,885 17000 2044

Accessories CoK Power-operated Face Drivers Type 680-10 Driving discs, toothed right-hand rotation Item no. Clamping circuit Ø S Approx. turning range I R V Matching center point Ø Y Weight 088061 8 9-16 4,5 38 4 4 120 088062 10 11-20 4,5 38 4 4 120 088063 12 13-24 7 36 4 6 120 088064 16 17-32 11 33 4 10 120 088065 20 21-40 13 30 4 12 120 088066 25 26-50 17 30 8 16 150 088067 32 33-64 22 30 10 16 190 Driving discs with carbide toothing, friction lining or diamant granulation on request Accessories Face drivers CoK Type 680-20 Driving discs, toothed left-hand rotation Item no. Clamping circuit Ø S Approx. turning range I R V Matching center point Ø Y 088081 8 9-16 4,5 38 4 4 120 088082 10 11-20 4,5 38 4 4 120 088083 12 13-24 7 36 4 6 120 088084 16 17-32 11 33 4 10 120 088085 20 21-40 13 30 4 12 120 088086 25 26-50 17 30 8 16 150 088087 32 33-64 22 30 10 16 190 Driving discs with carbide toothing on request Weight Type 680-12 Driving discs, with interchangeable hard metal driving plates 6 x 3,2 which can be used on 4 sides right-hand rotation Item no. Clamping circuit Ø S Approx. turning range H C Matching center point Ø Y 088068 40 41-80 20 24 16 200 088069 50 51-100 28 24 16 240 088070 63 64-126 41 24 16 400 088071 80 81-160 58 24 16 600 Weight Type 680-22 Driving discs, with interchangeable hard metal driving plates 6 x 3,2 which can be used on 4 sides left-hand rotation Item no. Clamping circuit Ø S Approx. turning range H C Matching center point Ø Y 088088 40 41-80 20 24 16 200 088089 50 51-100 28 24 16 240 088090 63 64-126 41 24 16 400 088091 80 81-160 58 24 16 600 Weight 2045

Accessories CoK Power-operated Face Drivers Power-operated Face Drivers CoK Tool group C15 Type 689-40 Centres, CoK Item no. Clamping circuit Ø N U Y Z Workpiece weight max. kg 088121 8-10 67,5 28 4 15 25 55 088122 12 67 28 6 15 75 55 088123 16 67 28 10 15 150 55 088124 20-32 64 25 12 15 250 55 085002 40-80 60 21 M 14x1,5 15 350 55 Weight Type 680-90 Hard metal driving plates right- or left-hand rotation Item no. Size Clamping circuit Ø Weight 088209 9,5x3,2 40-80 4 Type 680-93 Hard metal driving plates right- and left-hand rotation Item no. Size Clamping circuit Ø Weight 087931 9,5x3,2 40-80 4 Tool group C15 Typ 680-90 Clamping spindle Item no. Size Clamping circuit Ø Weight 088205 M 5 x 8 40-80 2 Tool group C15 Type 5191-Y O-ring Item no. Size 006252 21,82x3,53 2046

CoK 50-250 mm Power-operated Face Drivers L E G I A T D B Z Y High precision concentricity due to fixed centre point. Driving discs are pressed against the workpiece by power operated means. Clamping circuit Ø 50-250 mm Mechanically compensated Longitudinal workpiece stop in the centre Technical features: - high precision concentricity due to fixed centre point also under hard continuous operating conditions - minimal centering power even with maximum cutting load - workpiece weight max. 500 kg - slip-on driving discs, solid centre Accessories Face Drivers CoK F P H Tool group C15 Type 690-50 Power-operated driving head with centre Mechanically compensated Item no. A D E F G H I L P R T Y Z Weight 689085 182 100 M 10 15 25 154 16 max 150 min 134 96 38 120 M 20x1,5 22 18000 Draw-off nut M 20x1,5 item-no. 089302 Adapter plate CoK Type 688-87 Adapter plate short taper without spring set Item no. Design Taper A B D I K Weight 088485 DIN 55026 5 140 30 100 38 82,563 3100 088486 DIN 55026 6 167 35 100 38 106,39 4800 088487 DIN 55026 8 216 40 100 38 139,735 8700 088488 DIN 55026 11 280 45 100 38 196,885 17000 088480 DIN 55027 5 140 30 100 38 82,563 3100 088481 DIN 55027 6 167 35 100 38 106,39 4800 088482 DIN 55027 8 216 40 100 38 139,735 8700 088483 DIN 55027 11 280 45 100 38 196,885 17000 088495 DIN 55029 5 140 30 100 38 82,563 3100 088496 DIN 55029 6 167 35 100 38 106,39 4800 088497 DIN 55029 8 216 40 100 38 139,735 8700 088498 DIN 55029 11 280 45 100 38 196,885 17000 2047

Power-operated Face Drivers Driving discs CoK R R R R R R R R Power-operated Face Drivers CoK S S S S S S S S Type 687-13 Driving discs with interchangeable hard metal driving plates right-hand rotation Item no. Clamping circuit Ø S R Hard metal driving plate Weight 689461 50 48 6 x 5T 1400 689462 63 45 6 x 5T 1500 689463 80 38 6 x 5T 1500 689464 100 38 6 x 5T 1400 689465 125 38 12 x 5T 1800 689466 160 38 12 x 5T 2500 689467 1) 200 38 12 x 5T 2500 689468 1) 250 38 12 x 5T 3200 1) Weight reduced R R R R R R R R S S S S S S S S Type 687-23 Driving discs with interchangeable hard metal driving plates left-hand rotation Item no. Clamping circuit Ø S R Hard metal driving plate Weight 689371 50 48 6 x 5T 1400 689372 63 45 6 x 5T 1500 689093 80 38 6 x 5T 1500 689094 100 38 6 x 5T 1400 689095 125 38 12 x 5T 1800 689096 160 38 12 x 5T 2500 689097 1) 200 38 12 x 5T 2500 689098 1) 250 38 12 x 5T 3200 1) Weight reduced 2048

Accessories CoK Power-operated Face Drivers Type 680-90 Hard metal driving plates right- or left-hand rotation Tool group C15 Type 0167-Y Threaded pin Item no. Size Weight 312675 6 x 5 T 3 312911 12 x 5 T 6 Item no. Size Weight 048205 M 5 x 8 1 036461 M 5 x 10 1 Accessories Face Drivers CoK Tool group C15 Type 5191-Y O-ring Item no. Size 006283 59,69x5,33 Tool group C15 Type 689-40 Centres, CoK Item no. N U Y Z Weight 313621 54 24 M 20x1,5 22 112 N 2049

Power-operated Face Drivers Power-operated Driving Heads CoK Power-operated Face Drivers CoK CoK, for hard continuous operating conditions. Bolt on power-operated face driver heads, hydraulically compensated with interchangeable driving pins. Driving pins can be changed to allow right-hand and left-hand rotation. Technical features: - max. compensating range of driving pins approx. 8 mm - nominal value for max. loading approx. 4000 dan - max. workpiece weight 800 kg - On request: power-operated Face Driving Head CoK mechanically compensated and special designs Tool group C15 Type 689-10 Power-operated Face Driving Head size 1 CoK; hydraulic right-hand rotation Item no. S Approx. turning range A C D E F G H L O T V Y Z Pin Weight 088441 63 65-125 142 6 100 M 10 15 35 26 138 max. 143 72 120 16 max. 21 M 20x1,5 22 16 A 12000 088442 75 80-150 142 9,5 100 M 10 15 35 26 138 max. 143 72 120 16 max. 21 M 20x1,5 22 16 H 12000 088443 80 82-160 142 14,5 100 M 10 15 35 26 138 max. 143 72 120 16 max. 21 M 20x1,5 22 16 C 12000 CoK, for hard continuous operating conditions. Bolt on power-operated face driver heads, hydraulically compensated with interchangeable driving pins. Driving pins can be changed to allow right-hand and left-hand rotation. Technical features: - max. compensating range of driving pins approx. 8 mm - nominal value for max. loading approx. 4000 dan - max. workpiece weight 800 kg - On request: power-operated Face Driving Head CoK mechanically compensated and special designs Tool group C15 Type 689-10 Power-operated Face Driving Head size 2 CoK; hydraulic right-hand rotation Item no. S Approx. turning range A C D E F G H L O T V Y Z Pin Weight 088444 83 85-165 142 6 100 M 10 15 35 26 138 max. 143 92 120 16 max. 21 M 20x1,5 22 16 A 13000 088445 95 100-190 142 9,5 100 M 10 15 35 26 138 max. 143 92 120 16 max. 21 M 20x1,5 22 16 H 13000 088446 100 102-200 142 14,5 100 M 10 15 35 26 138 max. 143 92 120 16 max. 21 M 20x1,5 22 16 C 13000 2050

Power-operated Face Drivers Power-operated Driving Heads CoK CoK, for hard continuous operating conditions. Bolt on power-operated face driver heads, hydraulically compensated with interchangeable driving pins. Driving pins can be changed to allow right-hand and left-hand rotation. Technical features: - max. compensating range of driving pins approx. 8 mm - nominal value for max. loading approx. 4000 dan - max. workpiece weight 800 kg - On request: power-operated Face Driving Head CoK mechanically compensated and special designs Power-operated Face Drivers CoK Tool group C15 Type 689-10 Power-operated Face Driving Head size 3 CoK; hydraulic right-hand rotation Item no. S Approx. turning range A C D E F G H L O T V Y Z Pin Weight 088447 108 100-215 152 6 100 M 10 15 35 26 138 max. 143 117 120 16 max. 21 M 20x1,5 22 16 A 16000 088448 120 125-240 152 9,5 100 M 10 15 35 26 138 max. 143 117 120 16 max. 21 M 20x1,5 22 16 H 16000 088449 125 127-250 152 14,5 100 M 10 15 35 26 138 max. 143 117 120 16 max. 21 M 20x1,5 22 16 C 16000 CoK, for hard continuous operating conditions. Bolt on power-operated face driver heads, hydraulically compensated with interchangeable driving pins. Driving pins can be changed to allow right-hand and left-hand rotation. Technical features: - max. compensating range of driving pins approx. 8 mm - nominal value for max. loading approx. 4000 dan - max. workpiece weight 800 kg - On request: power-operated Face Driving Head CoK mechanically compensated and special designs Tool group C15 Type 689-10 Power-operated Face Driving Head size 4 CoK; hydraulic right-hand rotation Item no. S Approx. turning range A C D E F G H L O T V Y Z Pin Weight 088450 143 145-285 182 6 100 M 10 15 35 26 138 max. 143 152 120 16 max. 21 M 20x1,5 22 16 A 23000 088451 155 160-310 182 9,5 100 M 10 15 35 26 138 max. 143 152 120 16 max. 21 M 20x1,5 22 16 H 23000 088452 160 162-320 182 14,5 100 M 10 15 35 26 138 max. 143 152 120 16 max. 21 M 20x1,5 22 16 C 23000 2051

Power-operated Face Drivers Power-operated Driving Heads CoK Power-operated Face Drivers CoK CoK, for hard continuous operating conditions. Bolt on power-operated face driver heads, hydraulically compensated with interchangeable driving pins. Driving pins can be changed to allow right-hand and left-hand rotation. Technical features: - max. compensating range of driving pins approx. 8 mm - nominal value for max. loading approx. 4000 dan - max. workpiece weight 800 kg - On request: power-operated Face Driving Head CoK mechanically compensated and special designs Tool group C15 Type 689-20 Power-operated Face Driving Head size 1 CoK; hydraulic left-hand rotation Item no. S Approx. turning range A C D E F G H L O T V Y Z Pin Weight 088461 63 65-125 142 6 100 M 10 15 35 26 138 max. 143 72 120 16 max. 21 M 20x1,5 22 16 A 12000 088462 75 80-150 142 9,5 100 M 10 15 35 26 138 max. 143 72 120 16 max. 21 M 20x1,5 22 16 H 12000 088463 80 82-160 142 14,5 100 M 10 15 35 26 138 max. 143 72 120 16 max. 21 M 20x1,5 22 16 C 12000 CoK, for hard continuous operating conditions. Bolt on power-operated face driver heads, hydraulically compensated with interchangeable driving pins. Driving pins can be changed to allow right-hand and left-hand rotation. Technical features: - max. compensating range of driving pins approx. 8 mm - nominal value for max. loading approx. 4000 dan - max. workpiece weight 800 kg - On request: power-operated Face Driving Head CoK mechanically compensated and special designs Tool group C15 Type 689-10 Power-operated Face Driving Head size 2 CoK; hydraulic left-hand rotation Item no. S Approx. turning range A C D E F G H L O T V Y Z Pin Weight 088464 83 85-165 142 6 100 M 10 15 35 26 138 max. 143 92 120 16 max. 21 M 20x1,5 22 16 A 13000 088465 95 100-190 142 9,5 100 M 10 15 35 26 138 max. 143 92 120 16 max. 21 M 20x1,5 22 16 H 13000 088466 100 102-200 142 14,5 100 M 10 15 35 26 138 max. 143 92 120 16 max. 21 M 20x1,5 22 16 C 13000 2052

Power-operated Face Drivers Power-operated Driving Heads CoK CoK, for hard continuous operating conditions. Bolt on power-operated face driver heads, hydraulically compensated with interchangeable driving pins. Driving pins can be changed to allow right-hand and left-hand rotation. Technical features: - max. compensating range of driving pins approx. 8 mm - nominal value for max. loading approx. 4000 dan - max. workpiece weight 800 kg - On request: power-operated Face Driving Head CoK mechanically compensated and special designs Power-operated Face Drivers CoK Tool group C15 Type 689-20 Power-operated Face Driving Head size 3 CoK; hydraulic left-hand rotation Item no. S Approx. turning range A C D E F G H L O T V Y Z Pin Weight 088467 108 100-215 152 6 100 M 10 15 35 26 138 max. 143 117 120 16 max. 21 M 20x1,5 22 16 A 16000 088468 120 125-240 152 9,5 100 M 10 15 35 26 138 max. 143 117 120 16 max. 21 M 20x1,5 22 16 H 16000 088469 125 127-250 152 14,5 100 M 10 15 35 26 138 max. 143 117 120 16 max. 21 M 20x1,5 22 16 C 16000 CoK, for hard continuous operating conditions. Bolt on power-operated face driver heads, hydraulically compensated with interchangeable driving pins. Driving pins can be changed to allow right-hand and left-hand rotation. Technical features: - max. compensating range of driving pins approx. 8 mm - nominal value for max. loading approx. 4000 dan - max. workpiece weight 800 kg - On request: power-operated Face Driving Head CoK mechanically compensated and special designs Tool group C15 Type 689-20 Power-operated Face Driving Head size 4 CoK; hydraulic left-hand rotation Item no. S Approx. turning range A C D E F G H L O T V Y Z Pin Weight 088470 143 145-285 182 6 100 M 10 15 35 26 138 max. 143 152 120 16 max. 21 M 20x1,5 22 16 A 23000 088471 155 160-310 182 9,5 100 M 10 15 35 26 138 max. 143 152 120 16 max. 21 M 20x1,5 22 16 H 23000 088472 160 162-320 182 14,5 100 M 10 15 35 26 138 max. 143 152 120 16 max. 21 M 20x1,5 22 16 C 23000 2053

Accessories CoK Power-operated Face Drivers Tool group C15 Type 689-40 Centres, CoK Item no. N U Y Z Weight 085015 76 26 M 20x1,5 22 150 Accessories Face Drivers CoK Tool group C15 Type 689-91 driving pins, right-hand rotation 16 A 16 H Item no. Diameter Size C Length Weight 085383 16 16 A 6 60 80 088100 16 16 H 9,5 60 90 085052 16 16 C 14,5 60 85 16 C Tool group C15 Type 689-92 driving pins, left-hand rotation 16 A 16 H Item no. Diameter Size C Length Weight 085016 16 16 A 6 60 80 088099 16 16 H 9,5 60 90 085051 16 16 C 14,5 60 85 16 C Type 680-90 Hard metal driving plates right- or left-hand rotation Item no. Size Clamping circuit Ø Weight 088209 9,5x3,2 40-80 4 088209 2054

Constant face driver Clamping power diagramm Cutting capacity mm 2 Workpiece strength dan/mm 2 Turning dia. Clamping ratio = Clamping dia. Nominal values for tailstock loading F Tailstock dan* 0,5 0,63 0,8 1 40 50 63 80 100 125 0,8 0,9 1 1,12 1,25 1,4 1,6 1,8 2 2,24 2,5 Clamping power diagram Cutting capacity = depth of cut x advance (feed) 1,25 1,6 2 2,5 3,15 4 5 6,3 8 10 EXAMPLE A 100 112 125 140 160 180 200 224 250 280 315 355 400 450 500 560 630 710 800 900 1000 1120 1250 1400 1600 1800 2000 2240 2500 2800 Clamping-Ø 50 Turning-Ø 60 ø 50 ø 60 Example A Turning against the headstock 1. Cutting capacity: 6 x 0,4 = 2,4 mm 2 2. Workpiece strength: = 63 dan/mm 2 3. Clamping ratio: 60 : 50 = 1,2 4. Tailstock loading from graph: F Tailstock = 450 dan * Conversation factor for: B Radial grooving F Tailstock x 1,5 C Turning against tailstock F Tailstock x2 6 0,4 C B A When using several cutters at once, the calculated tailstock loading must be added. Workpiece strength 40 50 63 80 100 125 Material St 34-37 St 42 St 50 St 60-70 20 MnCr 5 18CrNi 8 9-15 S 20 C 10 C 15-22 C 35-45 C 60 30 CrMoV 9 GG 14-35 GG 40 22 S 20 16 MnCr 5 15 CrNi 6 50 CrMo 4 GGG-38 GGG-42 GGG-50 GGG-60 GGG-80 105 WCr 6 The RÖHM slide rule, Item No. 88231 may also be used for easy calculation of the axial clamping power. 2055

The headquarter: our parent plant in Sontheim/Brenz. The RÖHM parent plant is located in Sontheim/Brenz. In this ultra-modern production facility comprising 41,000 m², optimum conditions have been achieved in order to solve the extensive range of discerning construction and production tasks making the company even better, faster and more efficient in the future. Sontheim/Brenz All national and international activities are planned and co-ordinated at the administrative headquarters in Sontheim. Thanks to the excellent infrastructure and transport routes available, this location is ideal for a company relying on perfect product quality as well as maximum flexibility. Furthermore, the region around Sontheim offers another key basis for the success of our company: it is rich in quality awareness and motivated employees with the result that we are ideally prepared for the challenges of the future. The parent plant uniquely unites mass production, serial production and customised individual production under a single roof.

Key locations for the company: Dillingen and St. Georgen. Such strong growth on the part of the RÖHM Group is also obviously associated with higher requirements on development and production capacities. The demands of today and tomorrow can be complied with the two facilities in Dillingen and St. Georgen. Dillingen/Danube St. Georgen Plant: Dillingen/Danube This branch plant in Dillingen was put into operation by the RÖHM Group as early as 1953. Thanks to extremely positive development, the plant is subject to constant expansion and modernisation. For this reason, new modern production facilities were built in 1982 and 1991. In 2007 RÖHM built a new production hall for two portal turning and milling machines. This enables machining of workpieces up to 4 metres in length which will secure a leading market position for the RÖHM brand in the future. More than 300 employees are primarily involved in engineering and manufacturing lathe chucks, machine vices and special clamping equipment for turning and milling machinery as well as for machining centres. Engineering and sales department St. Georgen Apart from standard mandrels, tailor-made solutions for a wide variety of requirements are also manufactured here in this small but accomplished high-tech forge. RÖHM retains mechanical or power-operated mandrels, sliding jaw mandrels and hydraulic mandrels for its customers for tensioning workpieces in drill holes or interior contours.

Manufacturing and distribution Agents Always close to our customers. With locations all around the world. Customer orientation at RÖHM has less to do with marketing than with attitude. We consider customer proximity as an intensive dialogue with our partners as well as direct presence on key international markets. The RÖHM manufacturing and distribution bases: RÖHM IND. E COM. DE FERRAMENTAS DE FIXAÇÃO LTDA. Brazil ROEHM China Co., Ltd. China RÖHM Værktoj A. S. Denmark RÖHM S. A. R. L. France ROHM (Great Britain) LTD. Great Britain RÖHM SLOVAKIA S.R.O. Slovakia ROHM INDIA PVT. LTD. India RÖHM Italia S. R. L. Italy RÖHM Spanntechnik AG Switzerland RÖHM Iberica S. A. Spain ROHM Products of America USA

Your contacts at RÖHM. Manufacturing and distribution bases Germany: RÖHM GmbH Heinrich-Röhm-Straße 50 89567 Sontheim/Brenz Tel 0049 73 25 16-0 Fax 0049 73 25 16-510 info@roehm.biz www.roehm.biz RÖHM GmbH Röhmstraße 6 89407 Dillingen Tel 0049 90 71 5 08-0 Fax 0049 90 71 5 08-174 infodlg@roehm.biz RÖHM GmbH Feldbergstr. 5 78112 St. Georgen Tel 0049 77 24 94 68 12 Fax 0049 77 24 51 89 Mobil 0171 7 63 67 35 stg.info@roehm.biz Brazil: RÖHM IND. E COM. DE FERRAMENTAS DE FIXAÇÃO LTDA. Rod. Raposo Tavares, Km 14, s/n 0 Bloco A e C - Parte -Jardim Bandeirantes CEP 05576-900 - São Paulo Tel 0055 11 37 32 22 22 Fax 0055 11 37 35 30 97 vendas@rohm.com.br China: ROEHM China Co., Ltd. Room 401, Building 22, No. 518 Xinzhuan Road, Songjiang District 201612 Shanghai Tel 0086 21 37 70 53 95 Fax 0086 21 37 70 53 76 roehmcn@roehm.biz ROEHM WEIDA MACHINERY (Shandong) Co. Ltd. (Joint Venture) ADD: 2 Zhonghan Road Manshan Town Wendeng Shandong China 264414 Tel 0086 631 8 54 99 86 Fax 0086 631 8 54 50 18 lts@weidapeacock.com Denmark: RÖHM Værktoj A. S. Gunnekær 2, 2610 Rødovre Tel 0045 36 41 22 66 Fax 0045 36 41 44 72 info@roehm.dk France: RÖHM S. A. R. L. 325, rue Paul Langevin 60740 St. Maximin Tel 0033 344 64 10 00 Fax 0033 344 64 00 68 fr.roehm@roehm.biz www.rohm.fr Great Britain: ROHM (Great Britain) LTD. Unit 12 the ashway centre Elm cresent Kingston-upon-Thames Surrey KT 2 6 HH Tel 0044 20 85 49 66 47 Fax 0044 20 85 41 17 83 rohmgb@roehm.biz www.uk.roehm.biz India: ROHM INDIA PVT. LTD. Plot No. A-53(B), Nallekandernahall Peenya 2nd Stage Industrial Area 2nd Main Road 560058 Bangalore India Tel 0091 80 41 49 29 07 Fax 0091 80 28 36 76 56 kthomas_64@yahoo.com Italy: RÖHM Italia S. R. L. Via Brescia 24/C 20063 Cernusco S. Naviglio Tel 0039 02 92 10 35 31 Fax 0039 02 92 10 17 53 rohmitalia@roehm.biz www.roehm-italia.it Slovakia: RÖHM Slovakia s.r.o. Partizanska 73 95701 Banovce nad Bebravou Slovakia Tel 00421 3 87 60 02 22 Fax 00421 3 87 60 02 24 info@roehm.sk Spain + Portugal: RÖHM Iberica S. A. C/Rejas, No. 9 Nave 11 D 28022 Madrid Tel 0034 91 3 13 57 90 Fax 0034 91 3 13 57 93 rohmiberica@roehm.biz www.roehm-iberica.es Switzerland: RÖHM Spanntechnik AG Feldstraße 39, 3360 Herzogenbuchsee Tel 0041 629 56 30 20 Fax 0041 629 56 30 29 roehmch@roehm-spanntechnik.ch www.ch.roehm.biz USA: ROHM Products of America 5155 Sugarloaf Parkway, Suite K Lawrenceville, GA 30043 Tel 001 770 963-8440 Fax 001 770 963-8407 rohmusa@roehm.biz www.us.roehm.biz Presence on all continents from A for Australia to V for Venezuela. You can receive the contact information of our worldwide representations easily through www.roehm.biz

Sales Agents in Germany Clamping technology - manual - Baden-Württemberg: Norbert Schrenk Tel. 0 71 21 / 5 14 76 05, Fax 0 71 21 / 5 14 76 06 Mobil 0152 / 22 88 70 11 E-mail: norbert.schrenk@roehm.biz Werner Schmautz Tel. 0 78 02 / 98 27 51, Fax 0 78 02 / 7 00 94 27 Mobil 0152 / 22 88 70 23 E-mail: werner.schmautz@roehm.biz Bayern (south): Dieter Rabus Tel. 0 73 54 / 9 37 49 74, Fax 0 73 47 / 9 37 49 75 Mobil 0152 / 22 88 70 24 E-mail: dieter.rabus@roehm.biz Bayern (north): Gerhard Häutle Tel. 0 90 71 / 7 22 03 Fax 0 90 71 / 7 22 03 Mobil 0152 / 22 88 70 15 E-mail: gerhard.haeutle@roehm.biz Hessen: Joachim Nagel Tel. 0 60 45 / 98 39 00 Fax 0 60 45 / 98 39 01 Mobil 0171 / 6 20 91 59 E-mail: joachim.nagel@roehm.biz Niedersachsen: Reiner Maahs Tel. 0 52 31 / 8 73 26 Fax 0 52 31 / 8 73 26 Mobil 0152 / 22 88 70 16 E-mail: reiner.maahs@roehm.biz Nordrhein-Westfalen: Ralf Schnichels Tel. 0 21 61 / 9 99 72 43, Fax 0 21 61 / 9 99 72 47 Mobil 0152 / 22 88 70 25 E-mail: ralf.schnichels@roehm.biz Thorsten Nolte Tel. 0 27 21 / 12 01 82 Fax: 0 27 21 / 71 70 69 Mobil 0152 / 22 88 70 31 E-mail: thorsten.nolte@roehm.biz Berlin, Mecklenburg-Vorpommern, Brandenburg, Sachsen-Anhalt: Hendrik Seifert please see - power operated - Sachsen, Sachsen-Anhalt,Thüringen: Thomas Fischer please see - power operated - Hamburg, Bremen, Schleswig-Holstein: Michael Biß Tel. 0 431 / 3 97 09 59, Fax: 0 431 / 3 97 09 60 Mobil 0152 / 22 88 70 27 E-mail: michael.biss@roehm.biz Automation Technology Germany / Europe Robert Baß Tel. 0 73 22 / 91 13 37 Fax 0 73 22 / 91 13 38 Mobil 0152 / 22 88 70 33 E-mail: robert.bass@roehm.biz Clamping technology - power operated - Baden-Württemberg: Michael Schmitz Tel. 00 33 / 388 72 04 03 Fax 00 33 / 173 76 87 00 Mobil 00 49 (0)152 / 22 88 70 18 E-mail: michael.schmitz@roehm.biz Michael Hartmann Tel. 0 90 73 / 91 41 6 Fax 0 90 73 / 91 41 7 Mobil 0152 / 22 88 70 28 E-mail: michael.hartmann@roehm.biz Frank Stier Tel. 0 74 26 / 91 37 70, Fax: 0 74 26 / 91 38 84 Mobil 0152 / 22 88 70 19 E-mail: frank.stier@roehm.biz Richard Sedlak Tel. 0 70 21 / 94 98 97 0 Fax. 0 70 21 / 94 90 72 Mobil 0152 / 22 88 70 30 E-Mail: richard.sedlak@roehm.biz Bayern (south): Dieter Baz Tel. 08649 / 98 63 75 Fax. 08649 / 98 63 76 Mobil 0152 / 22 88 70 26 E-mail: dieter.baz@roehm.biz Bayern (north): Christian M. Merkel Tel. 0 91 61 / 66 41 39 Fax 0 91 61 / 66 41 45 Mobil 0152 / 22 88 70 14 E-mail: christian.merkel@roehm.biz Berlin, Mecklenburg-Vorpommern, Brandenburg, Sachsen-Anhalt: Hendrik Seifert Tel. 0 30 / 70 07 24 59 Fax 0 30 / 70 07 24 59 Mobil 0152 / 22 88 70 32 E-mail: hendrik.seifert@roehm.biz Hessen: Klaus Dieter Hofmann Tel. 0 64 06 / 90 67 40 Fax 0 64 06 / 90 67 43 Mobil 0152 / 22 88 70 29 E-mail: k.d.hofmann@roehm.biz Niedersachsen: Reiner Maahs please see - manual - Hamburg, Bremen, Schleswig-Holstein: Michael Biß please see - manual - Nordrhein-Westfalen: Friedhelm Schneider Tel. 0 27 62 / 49 07 28 Fax 0 27 62 / 49 07 29 Mobil 0152 / 22 88 70 17 E-mail: friedhelm.schneider@roehm.biz Thorsten Nolte please see - manual - Sachsen, Sachsen-Anhalt,Thüringen: Thomas Fischer Tel. 0 37 41 / 52 13 56 Fax 0 37 41 / 52 97 70 Mobil 0152 / 22 88 70 10 E-mail: thomas.fischer@roehm.biz Mandrel Technology Germany Thomas Haas Tel. 0 77 25 / 91 48 95 Fax 0 77 25 / 91 48 96 Mobil 0152 / 22 88 71 20 E-mail: thomas.haas@roehm.biz Agents worldwide Argentina: Himaq S.R.L., Venezuela 3652, 1603 Villa Martelli Prov. Buenos Aires Tel. 00 541 / 147 093 505, Fax 00 541 / 147 093 472 E-mail: himaq@himaq.com.ar Australia: White International Pty. Ltd., PO Box 304 Milperra LPO NSW 2214 Tel. 00 61 / 2 97 83 60 00 Fax 00 61 / 2 97 83 60 01 E-mail: sales@whiteint.com.au Austria: Richard Schörkhuber Lichtenhof 2 b 8511 St. Stefan ob Stainz Tel. 00 43 / 34 63 / 8 15 10 Fax 00 43 / 34 63 / 8 15 60 Mobil 00 43 / 664 / 9 23 77 10 E-mail: richard.schoerkhuber@roehm.biz Schachermayer GmbH, Schachermayer Str. 2 Postfach 3000, 4021 Linz Tel. 00 43 / 732 / 65 99-0, Fax 00 43 / 732 / 65 99 14 44 E-mail: maschinenmetall@schachermayer.at Lackner u. Urnitsch GmbH Bahnhofgürtel 37 8020 Graz Tel. 00 43 / 316 / 71 14 80-0 Fax 00 43 / 316 / 71 14 80 39 E-mail: lackner@urnitsch.at Haberkorn Ulmer GmbH Hohe Brücke 6961 Wolfurt Tel. 00 43 / 55 74 / 69 5-0 Fax 00 43 / 55 74 / 69 5-99 E-mail: info.wolfurt@haberkorn.com Metzler GmbH u. Co. KG Oberer Paspelsweg 6-8 6830 Rankweil Tel. 00 43 / 55 22 / 7 79 63-0 Fax 00 43 / 55 22 / 7 79 63-6 E-mail: office@metzler.at Belgium: (Clamping technology - manual -) BELTRACY Bergensesteenweg 189 1600 Sint-Pieters-Leeuw Tel. 00 32 / 25 43 68 90 Fax 00 32 / 25 38 59 10 E-mail: info@beltracy.be www.beltracy.be (Clamping technology - power operated -) RÖHM S.A.R.L. 325, rue Paul Langevin 60740 St. Maximin France Tel. 0033 / 344 64 10 00 Fax. 0033 / 34 64 00 68 E-mail: fr.roehm@roehm.biz www.rohm.fr Bosnia-Herzegovina: Kruhek d.o.o., Veprinacka 16, 10000 Zagreb (Kroatien) Tel. 00 38 / 513 695 138 Fax 00 38 / 513 639 530 E-mail: kruhek@zg.t-com.hr Canada: (Clamping technology - manual -) Sowa Tool & Machine CO. LTD 500 Manitou drive N2G 4B6 Kitchener, Ontario Tel. 001 / 519 / 748 / 57 50 Fax 001 / 519 / 748 / 93 04 E-mail: sales@sowatool.com (Clamping technology - power operated -) ROHM Products of America 5155 Sugarloaf Parkway, Suite K Lawrenceville, GA 30043 Tel. 001 / 770 / 963 / 8440 Fax 001 / 770 / 963 / 8407 E-mail: rohmusa@roehm.biz www.us.roehm.biz Chile: Robert Kralemann, SERVICOMP Ltda. Av. Departamental 1595 La Florida - Santiago Tel. 00 56 / 2 / 8 89 47 00 E-mail: rkralemann@gmail.com Columbia: Imocom S. A. Apartado Aereo 12287, Bogota D. E. 6 Tel. 00 57-1 / 2 62 38 00 Fax 00 57-1 / 2 62 49 82 E-mail: imocom@imocom.com.co Costa Rica: Servicios Centroamericanos, S.A. 625 Mts. Este del Parque de Tibás, frente a Autos La FLORIDA, SAN JOSÈ, COSTA RICA P.O. Box : 4711-1000 SAN JOSE, COSTA RICA Tel. 00 506 / 2 40 11 11 Fax 00 506 /2 40 22 22 E-mail: sercensa@sercensa.com Croatia: Kruhek d.o.o., Veprinacka 16 10000 Zagreb (Croatia) Tel. 00 385 - / 0 / 1-36 95-138 Fax 00 385 - / 0 /1-36 39-530 GSM: 00 385 - / 0 / 98-382 - 003 E-mail: kruhek@zg.t-com.hr www.kruhek.hr Czech Republic: Jan Vyslouzil Jiráskova 551 76824 Hulin Tel. 00 420 / 5 73 35 18 00 Fax 00 420 / 5 73 35 29 00 E-mail: janvyslouzil@iol.cz Ecuador: Maquinarias Henriques C.A. Casilla 4361, Via a Daule KM.6 1/2 Guayaquil / Ecuador Tel. 00 593-4 / 2 25 43 00 Fax 00 593-4 / 2 25 43 00 181 E-mail: info@maquinarias-henriques.com Finland: Oy Interfii Ltd, Teollisuuskatu 35-39 LH4 20520 Turku Y-tunnus 2374026-3 Tel. 00 358 / 2 01 47 45 00 Fax. 00 358 / 2 01 47 45 01 Email: info@interfii.com (Clamping technology - manual -) Teräskonttori Oy, Muuntotie 3, 1510 Vantaa Tel. 00 358 / 9 61 54 71 Fax 00 358 / 9 67 49 54 E-mail: info@teraskonttori.fi Greece: Stefanos Papadopoulos, Kifisiasstr. 15, 54655 Thessaloniki Tel. 00 30 / 23 10 48 87 58 Fax 00 30 / 23 10 48 87 53 E-mail: ST-papas@otenet.gr Hungary: Fairtool GmbH Koebanyai ut. 47/B H-1101 Budapest Tel. 00 361 / 8 14 46 21 Fax 00 361 / 2 61 95 61 E-mail: jozsef.alker@fairtool.hu Indonesia: GP System Singapur PTE LTD No. 51, Bukit Batok Crescent, #04-04/05 Unity Centre Singapore 658077 Tel. 00 65 / 68 61-26 63, Fax: 35 00 E-mail: enquiry@gpsystem.com

Agents worldwide Iran: Sakht Abzar Pars Co. (SAP) No. 19/4 Saeb Tabrizi St., North Abbas Shirazi Ave, Molla Sadra Ave., Tehran post code 19917 Tel. 00 98 / 21 / 88 03 18 88 Fax 00 98 / 21 / 88 03 77 33 E-mail: sales@sap-iran.com Ireland: ROHM (Great Britain) LTD. Unit 12 the ashway centre Elm cresent Kingston-upon-Thames Surrey KT 2 6 HH Tel. 0044-20 85 49 66 47 Fax. 0044-20 85 41 17 83 rohmgb@roehm.biz www.uk.roehm.biz Israel: ETMOS Tool Distributing Co. Ltd. Industrial Zone, P.O. Box 1786, Holon 58117 Tel. 00 972-3 / 55 81 933 Fax 00 972-3 / 55 81 934 E-mail: etmos@etmos.co.il Japan: Takeda Trade Co., Ltd. Tokyo office 113-0033, 3-5-2 Hongo Bunkyo-ku Tokyo / Japan Tel. 00 81/33815 6501 Fax 00 81/33816 4522 E-mail: hata@takeda-trade.co.jp Luxembourg: RÖHM S.A.R.L., 325 rue Paul Langevin 60740 St. Maximin Tel. 00 33 / 3 44 64 10 00 Fax 00 33 / 3 44 64 00 68 E-mail: fr.roehm@roehm.biz Malaysia: GP System Singapur PTE LTD No. 51, Bukit Batok Crescent, #04-04/05 Unity Centre Singapore 658077 Tel. 00 65 68 61-26 63, Fax: 35 00 E-mail: enquiry@gpsystem.com Marocco: Somadu 20-22, Bd. Abdellah Ben Yacine, Casablanca 20300 Tel. 00 21 222/30 05 90, Fax 45 06 10 E-mail: alaoui.my.youssef@somadu.com Macedonia: G.T.M.Co. d.o.o. Export - Import Autoput Bg - Zg br. 22 11080 Beograd Srbija i Crna Gora Tel. 00 381 / 1 13 14 90 24 Fax 00 381 / 1 13 14 90 21 E-mail: vladimir.rackovic@gtmco.rs Mexico: Sales Power de Mexico S.A. DE C.V. Calle Jalpan No. 701 76030 C.P. QUERETARO, QRO.-COL.EST Tel. 00 52-442 / 2 14 55 43 Fax 00 52-442 / 2 24 01 12 E-mail:salesfob@salespower-tools.com Netherlands: (Clamping technology - manual -) Boorwerk B.V., Flevolaan 52 A, Industrieterrian Noord 1382 JZ Weesp Tel. 00 31 / 294 / 43 20 50 Fax 00 31 / 294 / 43 21 52 E-mail: info@boorwerk.nl (Clamping technology - power operated -) Friedhelm Schneider Tel. 0049 / 27 62 / 49 07 28 Fax 0049 / 27 62 / 49 07 29 E-mail: friedhelm.schneider@roehm.biz Norway: Ing. Yngve Ege A/S Ryenstubben 5 0679 Oslo 11 Tel. 00 47 / 23 24 10 00 Fax 00 47 / 23 24 10 01 E-mail: ege@ege.no Poland: RÖHM GmbH Heinrich-Röhm-Straße 50 89567 Sontheim/Brenz (Germany) Tel 0049 73 25 16-0 Fax 0049 73 25 16-512 info@roehm.biz Portugal: RÖHM Iberica S. A. C/Rejas, No. 9 Nave 11 D 28022 Madrid Tel. 0034 / 91 / 3 13 57 90 Fax 0034 / 91 / 3 13 57 93 rohmiberica@roehm.biz www.rohm-iberica.es Russia: RÖHM GmbH Heinrich-Röhm-Straße 50 89567 Sontheim/Brenz (Germany) Tel 0049 73 25 16-0 Fax 0049 73 25 16-512 info@roehm.biz OOO T.W.L -Group Kosmonavta Volkova 5, stroenie 1, 127299 Moscow, Russia Tel. 007 / 495 / 5 04 72 39 007 / 903 / 1 03 29 02 Fax 007 / 495 / 6 18 42 68 E-mail: sales@twl-group.ru Saudi-Arabia, VAE, Bahrain, Kuwait, Yemen, Libya, Egypt: Dirk Jaegemann Trade agency GmbH & Co. KG Julius-Bamberger-Str. 1 28279 Bremen Tel. 04 21 / 8 39 21 30 Fax 04 21 / 8 39 89 21 E-mail: info@djta.de Sweden: Techpoint Systemteknik AB Nyponvaegen 4 19144 Sollentuna Tel. 00 46 / 86 23 13 30 Fax 00 46 / 86 23 13 45 E-mail: info@techpoint.se Serbia-Montenegro: G.T.M.Co. d.o.o. Export - Import Autoput Bg - Zg br. 22 11080 Beograd Srbija i Crna Gora Tel. 00 381 / 1 13 14 90 24 Fax 00 381 / 1 13 14 90 21 E-mail: vladimir.rackovic@gtmco.rs Singapore: GP System Singapur PTE LTD No. 51, Bukit Batok Crescent, #04-04/05 Unity Centre Singapore 658077 Tel. 00 65 / 68 61-26 63, Fax 00 65 / 68 61-35 00 E-mail: enquiry@gpsystem.com Slovenia: Kruhek d.o.o., Veprinacka 16 10000 Zagreb (Kroatien) Tel. 00 385 / 13 69 51 38 Fax 00 385 / 13 63 95 30 E-mail: kruhek@zg.t-com.hr Slovakia: MCS s. r. o. Heckova 31 SK - 97201 Bojnice Tel. 00 421 / 4 65 40 20 50 Fax 00 421 / 4 65 40 20 48 E-mail: michalovic@mcs.sk South Africa: Kingstone Tools & Accessories P.O. Box 75746 2047 Gardenview Tel. 00 27 / 11 / 6 22 16 68 / 9 Fax 00 27 / 6 15 42 10 E-mail: rohmtools@mweb.co.za South-Korea: Cheong Do Trading Co., Ltd. RM-6-103, 604-1 Kuro-Dong, Kuro-Ku, Seoul Tel. 00 822 / 6 78 41 55 Fax 00 822 / 67 25 48 3 E-mail: CDMT@chollian.net Taiwan: V.T.M. Company Ltd. No. 13-1 11th Road, Taichung Industrial Park Taichung, TAIWAN Tel. 00 886 / 4 / 23 59 27 59 Fax 00 886 / 4 / 23 50 74 27 Email: luck@vtm.com.tw Email: lily@vtm.com.tw Thailand: GP System Singapur PTE LTD No. 51, Bukit Batok Crescent, #04-04/05 Unity Centre Singapore 658077 Tel. 00 65 / 68 61 / 26 63 Fax 00 65 / 68 61 / 35 00 E-mail: enquiry@gpsystem.com Turkey : Sintek Mühendislik Makina San. Ve Tic. Ltd. Sti. Tarabya Mahallesi Yumak Sok. No: 3/A1 34457 SARIYER ISTANBUL Tel. 00 90 / 212 / 2 99 61 84 Fax 00 90 / 212 / 2 99 56 75 E-Mail: sinan.onurlu@sintekmuhendislik.com Ukraine: T.W.L.-JUGA-Service 41, Gradonochalnitzkaya str. 1 65005 Odessa, Ukraine Tel. 00380 / 48 / 79 5 85 64 Fax 00380 / 48 / 7 94 94 68 E-mail: jugtech@twlweb.biz Venezuela: Hartung Hnos. Sucr. C. A., Apartado 2480 Caracas 1010-A / Venezuela Tel. 00 58 / 212 / 54 20 820 Fax 00 58 / 212 / 54 19 449 E-mail: claus@hartung.com.ve Maquinaria Diekmann S.A. AV. Humboldt Las Acacias CARACAS 1040 / VENEZUELA Tel. 00 58 / 212 / 633 36 30 or Tel. 00 58 / 212 / 633 62 30 Fax 00 58 / 212 / 633 22 62 or Fax 00 58 / 212 / 632 80 13 E-Mail: purchase@diekmann.com.ve Vietnam: CAP DO Industrial Equipment Co Ltd., 113/8A Tran Van Du Str. Ward 13, Tan Binh Dist. Ho-Chi-Minh-City Tel. 0084 / 8 / 38 10 45 33 Fax. 0084 / 8 / 38 10 84 27 E-Mail: capdo01@capdo.com.vn

General conditions of sale and delivery 1 Quotation, Formation of Contract and Content of Contract 1. The present General Terms of Sale and Delivery apply exclusively. We do not recognise any terms and conditions that are contradictory or different from our own, unless we have explicitly given our written agreement to do so. Our Terms of Sale and Delivery will also apply if we effect delivery to the Purchaser without any reservation in full awareness of the contradictory or different nature of the terms of the Purchaser, as compared to our own Terms. 2. Our quotations are always subject to change without notice unless they have been explicitly described as binding. The contract will only materialise upon our written confirmation and in line with the content thereof and by way of performance/delivery on our part. If delivery/service is immediately provided without any confirmation, the invoice will also be deemed to be the order confirmation. 3. Our General Terms of Sale and Delivery will only apply to a business entity as defined in Section 14 BGB [German Civil Code]. 4. Costs for the compilation of drawings for specific constructions will be borne by the Orderer if, for reasons for which we are not responsible, the quotation does not lead to an order placement. 5. All particulars regarding weights, dimensions, services and technical data that feature in our printed matter, catalogues, price lists or in other contract documents are only approximate, unless they have been explicitly described as binding. 6. We retain the right to amend the construction and form of the subject of contract, providing this does not involve unreasonable alterations for the Orderer. 7. The documentation comprises an assembly layout, piece list with details of the wearing and spare parts, as well as operational and maintenance instructions; this is always in the German language. Documentation is only in paper form or in digital form. For digital forms, the texts are provided in the formats.txt,.rtf or.doc; drawings and piece lists are in the.tif format (grid format). Any documentation in excess thereof will be billed and is subject to particular arrangement. 8. For testing, when specific temperatures, times and other measurements or control values are to apply, the appropriate measurement methods must be specified prior to delivery and acknowledged by both Parties. Unless such values are so defined, our own measurement methods will apply. 9. Samples will only be delivered subject to a fee. 10. Assurances given, ancillary agreements and changes to the contract will require the written form to be operative. It will not be possible to waive this requirement. 11. An order placement will be deemed irrevocable unless the Deliverer has agreed in writing to cancel it. 12. For export transactions, delivery will be subject to the conditions specified on the order confirmation; in addition, the respectively current version of the international trade definitions most commonly used in international sales contracts (incoterms 1953) will apply as devised by the International Chamber of Commerce. 13. In addition to the General Terms of Delivery and Sale, compliance with our product information sheets, the technical data sheets as well as other product-specific publications will apply, each in their current version. 2 Prices 1. Failing specific written agreement, prices apply as in the Federal Republic of Germany, free house plus the value added tax required by law. For export transactions, the item to be delivered is deemed sold ex works, unless the contract stipulates otherwise about the type of sale. For single orders for a value of goods less than 100.00 net, a handling fee of 10.00 plus the value added tax required by law will be charged throughout the country. 2. Please note that we only despatch the consignment at the request of the customer. Irrespective of this, the rulings laid down in Section 5 will apply. 3. We bill the prices that were valid when the contract was drawn up, based on the cost factors applicable at the time. Should these cost factors (particularly material, wages, energy etc.) alter during the period between the drawing up of contract and the agreed delivery time, we will be entitled to amend prices accordingly. For export transactions, the Deliverer will be entitled to cancel that part of the order that has not yet been completed or to adjust prices appropriately if the currency in which the contract was drawn up has devalued. 4. With an ex works contract, the goods will be transported at the expense and risk of the Orderer. For all consignments, the respectively current version of the provisions of incoterms 1953 will apply to the insurance and bearing of risk. 5. For parts/products that are produced in line with Purchaser requirements, we will notify the Purchaser of our production quantity. The Purchaser undertakes to take receipt of the quantity thus confirmed. 6. Over-deliveries and short-deliveries are admissible up to 5%; for special tooling up to 10% is admissible, at least, however, 2 (two) pieces. The respective delivery will be billed. 3 Modalities of Payment 1. Failing specific arrangements, payment is due without deduction and without charges within 10 days of the date of invoice - even for delivery instalments. 2. We are not bound to accept cheques or bills. In the event cheques or bills are accepted subject to prior arrangement in individual circumstances, this will only be as conditional payment, taking due account of discount charges and collection fees that are to be paid immediately in cash by the Customer. The ultimate credit entry of bills of exchange and cheques will be after their redemption. The acceptance of cheques or bills will be without prejudice for subsequent commitments to payment. We will not be liable for the punctual presentation, protest, notification and return of a bill in the event it is not honoured. 3. Any overshooting of the payment deadline will incur interest to the amount of the banks borrowing costs, at least, however 8% in excess of the respective basic interest rate of the European Central Bank. 4. If a bill or a cheque is not honoured on time or if a deadline for payment is overreached, all receivables still outstanding, including those that are deferred and those for which bills or cheques have been given, will become due for immediate payment. 5. The Purchaser will only be entitled to offset if the counterclaims he asserts have been established by declaratory judgment, if they are undisputed or have been acknowledged by us. The Purchaser will be authorized to exercise a right of retention to the extent his counterclaim is derived from the same contractual relations. 6. For export transactions, payments will be paid subject to the modalities of payment contracted. 7. Costs of payment transactions, particularly bank charges of foreign payment transfers to us, are in principle for debits of the client. 4 Delivery Period 1. The delivery period we specify begins to run providing all technical issues have been fully clarified. The delivery deadlines we give are in principle not binding and only constitute a probable delivery time. 2. The compliance with our commitment to deliver depends on the Purchaser having punctually and properly fulfilled his commitments, particularly his commitment to comply with the contracted terms of payment. The right to plea non-performance of contract will be retained. This right will also be derived from commitments that have not been satisfied in full from previous deliveries. 3. The period of delivery commences upon the despatch of the order confirmation, yet not before the Orderer has provided the documents, permits, clearance papers etc. to be procured and not before the agreed deposit has been received. 4. If a fixed delivery date has been arranged, the Deliverer will effect delivery on time. Compliance with the delivery period will be deemed given if the item to be delivered has left the works or the readiness for despatch has been notified before the expiry of said delivery period, subject to timely and accurate delivery from our own suppliers. If the Orderer amends parts of the consignment to be delivered, the delivery period will run anew upon confirmation of said amendment. 5. Force majeure, war, uprising, strike, lock-out or measures enforced by the authorities for whatever reason that impede delivery, as well as a lack of raw materials, means of transport and theft even with our own suppliers will release the Deliverer from his commitment to deliver within the specified period of time. The Orderer will be notified immediately of the occurrence of the hindrance and of the likely repercussions. 6. It is admissible to effect delivery prior to the expiry of the specified delivery period and to deliver in appropriate instalments. 7. Compliance with the delivery period depends on the fulfilment of all contractual duties of the Orderer. 8. In the event of delivery delays or of the impossibility of delivery, the provisions of Section 10 will apply. 5 Transfer of Risk and Taking Receipt 1. Risk will pass to the Orderer at the latest with the despatch of the consignment, even if delivery is to be in instalments or if we still have other services to provide, e.g. despatch costs or transport and delivery as well as installation. 2. At the request and at the expense of the Orderer, we will ensure insurance cover of the consignment to be delivered for theft, breakage and damages from transportation, fire and water and for other insurable risks. 3. If despatch is delayed for reasons for which the Orderer is responsible, the risk will pass to the Orderer as from the date of readiness for despatch; nevertheless, we undertake to ensure insurance cover at the request and expense of the Orderer as called for by the Orderer. 4. Even if the delivered items feature insignificant defects, the Orderer will take receipt thereof irrespective of the rights laid down in Section 8. 6 Default of Acceptance, Call-off Orders 1. If the Orderer fails to take receipt of the items contracted on time, we will be entitled to set the Orderer a subsequent period of grace after which we will be entitled to dispose of the items otherwise and supply the Orderer subject to a subsequently lengthened delivery period. Irrespective of this, we will be entitled to withdraw from the contract as defined in Section 326 BGB [German Civil Code] and to call for compensation for damages owing to non-performance. In the event we call for compensation for non-performance, we will be able to claim compensation of 25% of the agreed price plus value added tax without having to provide evidence. We retain the right to assert actual damages of a greater dimension. 2. Orders, which we confirm for call-off must be accepted within one year of the date of order placement at the latest - unless otherwise arranged. The same will apply to fixed reservations or to permanent call-off statuses. Section 6.1 will apply accordingly in the event the goods are not called off. 7 Retention of Title 1. The items for delivery (the goods subject to the retention of title) will remain our property until all claims to which we are entitled from the Purchaser from the business relations have been satisfied in full. Where the value of all security interests to which we are entitled against the Purchaser exceeds all secured claims by more than 10%, we will release some of the security interests as appropriate at the request of the Purchaser. 2. During the period in which title to the goods is retained, the Purchaser is not allowed to pledge or assign the goods as security and is only permitted to resell to resellers in normal business transactions and only providing the reseller receives payment from its own customer or subjects the customer s ownership of the item to the full satisfaction of the customer s commitments to payment. 3. In the event of attachment, seizure or any other disposition or third-party intervention in respect of the goods, the Purchaser will notify us immediately so that we can file action subject to Section 771 ZPO [German Code of Civil Procedure]. If the third party is not able to reimburse us for the court and out-of-court costs of legal action pursuant to Section 771 ZPO, the Purchaser will be liable for the loss we thus incur. 4. The Purchaser undertakes to treat the item purchased with care. In particular, the Purchaser undertakes at his own expense to ensure it is adequately insured at reinstatement value against damages from fire, water and theft. Should maintenance and inspection work be required, the Purchaser will have this carried out in good time at his own expense. 5. In the event of breaches of duty on the part of the Purchaser, particularly with default in payment, we will be entitled to cancel the contract and to take back the goods; the Purchaser undertakes to surrender the goods. If we take back the goods and/or assert the retention of title, this does not mean we are cancelling the contract, unless we have explicitly declared as much.

General conditions of sale and delivery 6. If the Purchaser has resold the item purchased in regular business transactions, the Purchaser herewith now assigns to us all claims to payment in the amount of the final invoice amount (including value added tax), such as due to the Purchaser from the resale to his customer or a third party, irrespective of whether the item purchased has been resold without or after further reworking. The Purchaser remains authorized to collect this payment, even after assignment. Our own authority to collect payment ourselves will not be affected hereby. However we undertake not to collect payment providing the Purchaser satisfies his own commitments to payment from the proceeds collected, does not default in payment and in particular providing the initiation of insolvency proceedings is not petitioned or payments cease to be made. Should this, however, be the case, we will be able to demand that the Purchaser provides us with details of the assigned payments and their debtors as well as all information necessary to collect payment, that he hands over the relevant documentation to us and notifies the debtors (third parties) of the assignment. 7. The processing or reworking of the item purchased by the Purchaser will always be carried out on our behalf. If the item purchased is processed with other items not belonging to us, we will acquire co-ownership to the new item to the value of the item purchased (final invoice amount including value added tax) in relation to the other processed items at the time of reworking. The same will apply to the thus newly created items as for the items delivered subject to retention of title. 8. If the item purchased is processed with other items not belonging to us, we will acquire co-ownership to the new item to the value of the item purchased (final invoice amount including value added tax) in relation to the other processed items at the time of reworking. If the intermixing is such that the Purchaser s item is to be deemed the main item, it is herewith agreed that the Purchaser will transfer co-ownership to us proportionately. The Purchaser will keep the property in which we hold exclusive ownership or co-ownership on our behalf. 8 Quality Defects We are liable for defects in quality as follows: 1. All parts or services will be remedied, at our discretion, free of charge or redelivered or provided again that are found to feature a quality defect during the statutory period of limitation - irrespective of service life - providing the origin thereof already existed at the time of the passing of risk. 2. Claims to quality defects will become statute-barred in 12 (twelve) months. The period of time commences with the passing of risk (Section 6). 3. The Purchaser will immediately file written objection to the quality defect with us. 4. In the event objections are filed, the Purchaser will be permitted to refrain from payment to an extent appropriate to the quality defects featured. The Purchaser will only be able to refrain from payment if an objection is asserted, the justification of which cannot be doubted. If the objection has been asserted unjustifiably, we will be entitled to call for the reimbursement of the expenses incurred by us. 5. Initially we will always be granted an opportunity to remedy a defect within an appropriate period of grace. 6. Should the remedy fail, the Purchaser notwithstanding any claims to damages will be able to cancel the contract or reduce remuneration. The Purchaser will only be able to call for the reimbursement of fruitless expenditure if the defect in question is attributable to our own wilful intent or gross carelessness for which we are responsible. 7. Claims to defects in quality are not given if the divergence from the agreed nature of the product is only minimal, if usability is only insignificantly impaired, in cases of natural depreciation or damages generated after passing of the risk as a result of faulty or negligent treatment, excessive exposure, unsuitable operating media or because of specific outer impact that was not to be expected given the contract, as well as in cases of non-reproducible software errors. If amendments or repair work is carried out improperly by the Purchaser or by third parties, there will be no claims to the defects resulting or the effects thereof. The same will apply to a lack of compliance with our instructions on handling and other instructions and if maintenance is not carried out properly 8. Claims of the Purchaser to a refund of the expenses incurred for the purpose of remedy, such as costs of transport, travel, labour and materials will be ruled out, when such expenses increase because the item delivered was brought to a destination other than the Purchaser s branch premises, unless said relocation is in accordance with the intended use of the item. 9. Legal claims to recourse against us on the part of the Purchaser will only be given if the Purchaser has entered into no agreement with his customer in excess of those claims to defects regulated by the law. 10. Claims to compensation for damages will be governed by Section 9. Any fartherreaching claims to quality defects or others than those governed in this Section or in Section 9 will be ruled out. 9 Industrial Property Rights and Copyrights, Defects of Title Unless otherwise agreed, we undertake to only effect delivery free from proprietary rights and third party copyrights (referred to in the following as industrial property rights) in the country of the delivery destination. In the event a third party files justified claims against the Purchaser for a breach of industrial property rights derived from deliveries we effected that are being used as contracted, we will be liable towards the Purchaser for the period of time specified in Section 8.2 as follows: 1. At our discretion and at our own expense, we will either procure a licence for the deliveries in question, alter them so that there is no breach of industrial property rights or we will provide a substitute. Should this not prove possible at appropriate conditions, the Purchaser will be entitled to the rights of cancellation or reduction as laid down by the law. The Purchaser will only be able to call for the reimbursement of fruitless expenditure if we are to blame for wilful intent or gross negligence. Our commitment to provide compensation for damages is governed by Section 10. 2. The above commitments will only be given if the Purchaser has given us immediate, written notification of the claims asserted by the third party, does not recognise any breach of rights and if we retain the right to initiate defence measures and negotiate a settlement. If the Purchaser ceases to use the item delivered in order to reduce damages or for other good cause, the Purchaser undertakes to inform the third party that this discontinuation of use does not embody any acknowledgement of a breach of industrial property rights. 3. Claims of the Purchaser will be ruled out if the Purchaser is responsible for the breach of industrial property rights. 4. Any claims of the Purchaser will also be ruled out if the breach of industrial property rights was derived from specific specifications of the Purchaser, from an application that we could not foresee or from the item delivered being altered by the Purchaser or used in combination with products that we have not delivered. 5. In the case of breaches of industrial property rights, the provisions of Sections 8.4, 8.5 and 8.9 will apply appropriately to the claims of the Purchaser governed by Section 13. 6. Any farther-reaching claims to defects of title of the Purchaser or claims other than those governed by the present Section 9 against us or our vicarious agents will be ruled out. 10 Overall Liability 1. Claims of the Purchaser to compensation for damages irrespective of the legal nature of the claim asserted will be ruled out. 2. The exceptions are: a) Damages due to the violation of major contractual duties (cardinal duties). However, in the case of simple negligence, liability for damages will be restricted to foreseeable, typically occurring damages. b) Damages derived from injury to life and limb if we are responsibility for the breach of duty. c) Damages attributable to wilfully intentional or negligent violations, said breach of duty on the part of our legal representatives or vicarious agents being of equal status to any breaches of duty on our part. d) Claim to damages for impossibility or inability. 3. Any alteration of the onus of proof to the detriment of the Purchaser does not relate to the above provisions. 4. Liability subject to the Product Liability Act remains unaffected hereby. 5. Where liability for compensation is ruled out or restricted in our respect, this will also apply to the personal liability for damages of our employees, our trade representatives and our vicarious agents. 11 Duties to Involvement of the Purchaser 1. The involvement of the Purchaser that has been agreed to explicitly or implicitly in the contract will be subject to no specific remuneration, unless otherwise explicitly agreed. 2. The Purchaser undertakes to inform us in good time of all facts, which indicate that stocks and products we have made available in the light of our notified production capacities cannot be used or not be used in full. Where stock remains, in the case of a premature change to his planning, the Purchaser will take over the remainder and any costs of destruction that might be incurred. This will also apply to products for which we have had to place orders for minimum quantities from our own suppliers, providing we previously advised the customer thereof. 3. The Purchaser guarantees that the products delivered by him for reworking are suitable for the purpose. We do not undertake to check the products delivered by the Purchaser for their quality and aptitude for reworking. In ongoing business relations and whenever an item for reworking has been initially checked, tested and released, the Purchaser undertakes to inform us in writing of each and every product amendment without actually being requested to do so. When items are being reworked, after every change in production conditions on his premises, in particularly when substituting tooling, machinery or introducing new production processes, the Purchaser also undertakes to examine the item to be processed by us for any divergence and alteration and to notify us in writing of any such divergence and alteration. 4. Instructions from our Purchaser, the selection of material or other specifications laid down by the Purchaser do not oblige us to check them for accuracy. 5. The Purchaser will hence check all instructions it issues as well as the quality of the material specified to us or made available to us for compliance with the law and technical regulations. 6. Should the Purchaser default in terms of its duties to provide or to become involved, we will be entitled to the rights stipulated by law. 7. In any case, goods may only be returned subject to the explicit consent of the Deliverer. Their return will be free-house and details of the order number and delivery date will be given as well as the original delivery packaging. The goods will be in their original condition, i.e. in an undamaged state. For the handling of a return, we charge 20% of the value of the goods, at least, however, 50.00 plus value added tax. In individual circumstances, the Deliverer retains the right to charge the Orderer a higher sum based on evidence. 12 Place of Performance and Jurisdiction/ Other 1. The place of performance and payment will be the registered office of our company in Sontheim/Brenz. 2. Exclusively the laws of the Federal Republic of Germany will govern the present contractual relations. The application of the United Nations Convention dated 11.04.80 on Contracts for the International Sale of Goods (CISG Wiener Kaufrecht ) is ruled out. 3. For all disputes derived from contractual relations, if the Orderer is a registered businessperson, a legal entity under public law or a separate estate under public law, legal action will be filed with the court of law with jurisdiction for our registered office. We will also be entitled to file legal action at the location of the registered seat of the Orderer. 4. Should any one condition of our General Terms of Sale and Delivery be void for any reason whatsoever, the validity of the remaining provisions will not be affected hereby. 5. We will save your data in accordance with Section 23 BDSG [Federal Data Protection Act]. RÖHM GmbH D 89565 Sontheim/Brenz Revised: September 2012

,, RÖHM we re here to serve you.

We offer real partnership. We see this reflected in collaborative partnerships both with specialist dealers as well as directly with consumers. We offer sound advice, provide comprehensive support and do our utmost for you, so that you get exactly the right solution for meeting your targets safely and economically. And if there isn t a solution available yet, then we ll design it.

RÖHM GmbH Heinrich-Röhm-Straße 50 89567 Sontheim/Brenz Germany Tel 0049 73 25 16-0 Fax 0049 73 25 16-510 info@roehm.biz www.roehm.biz Id.-Nr. 1178262 / 0313 CM