Eaton PVM Variable Displacement Piston Pumps Vickers Product Line 18-141cc 3 (1.1-8.6in 3 )
Table of Contents M Series Variable Displacement Piston Pumps Introduction.... 3 Hydraulic System Design Calculations.... 4 Model Code Selection.... 5 Model Code Options.... 6 Specifications and Performance... 8 Control Options.... 11 Performance Industrial PVM18.... 15 PVM2.... 2 PVM45.... 25 PVM5.... 3 PVM57.... 35 PVM63.... 4 PVM74.... 45 PVM81.... 5 PVM98.... 55 PVM16.... 6 PVM131.... 65 PVM141.... 7 Dimensions PVM18/2... 75 PVM45/5... 82 PVM57/63... 89 PVM74/81... 94 PVM98/16... 98 PVM131/141... 12 Mounting Flange Options.... 17 Shaft Options.... 18 Input Shaft Selection Data.... 111 Port Options.... 112 Operating Requirements and Recommendations.... 114 Installation and Start-up.... 115 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E1 March 214 2
Introduction Eaton M Series pumps are open circuit, axial piston designs. A variety of control options allows the pumps to perform most efficiently in a specific application. Efficiency of the pump controls allows down-sizing of system cooling needs, saving up front cost in the machine. Alternatively, cooling capacity could be kept the same and the flow capability of the system increased, thus improving performance and customer satisfaction. The M Series also contains a strong proven rotating group allowing the pumps to handle pressures to 28 bar (4 psi) continuous and 32 bar (46 psi) intermittent with less maintenance cost. High-load bearings and a stiff drive shaft help provide a pump life of 8 hours at rated industrial conditions, reducing operating costs and extending operating life. M Series pumps feature a saddle-type yoke with steel-backed polymer bearings. The stiff yoke reduces deflection and allows even loading of bearings, improving life. A single control piston reduces loading on the yoke, resulting in reduced pump size which allows installation in tighter locations. M Series pumps operate at a level of quietness that exceeds the requirements of today s demanding work conditions. The pumps feature a unique threepiece envelope (flange, housing and valve block) specifically created for low fluid-borne and structure-borne noise levels. Another pump feature a bimetal timing plate improves pump filling characteristics which, in turn, reduce fluid-borne noise and extend pump life. M Series pumps reduce, or in some cases remove, the need for damping barriers between the noise source and the operator. This saves money on the installed cost of the system while improving customer comfort. An adjustable maximum stop provides a means of tuning flow to your system, while gauge ports allow monitoring of inlet and outlet conditions. These standard features reduce system complexity and cost. Mounting flanges are offered in SAE and ISO config urations, and ports are offered in SAE, ISO, and BSPP in both tube and flange versions. This provides a wide variety of installation opportunities for global machine design. Side- or end-ported models are available to facilitate plumbing and help fit the pump to your machine space needs. Multiple drain ports allow many mounting orientations, reducing installed costs. M Series pumps are capable of operating with many types of hydraulic fluids used in industrial systems. High-water-content and phosphate ester fluids can be accommodated, in addition to the typical petroleum based and synthetic fluids. Typical Applications Mining machinery Injection molding machines Metal forming machines Oil and Gas Equipment Conveyor lines Primary metals Metal cutting equipment Features and Benefits Long pump life Quiet pump operation Inlet and outlet gauge ports and adjustable maximum displacement stops standards Astonishingly low 4% pressure ripple Low installed and operating costs Reduced maintenance Flexibility in machine design Design promotes leak-free system 3 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E1 March 214
Hydraulic System Design Calculations Basic Formulas Output Flow (Q) lpm = cm 3 /r x rpm gpm = in 3 /r x rpm 1 231 Input Power (P) kw = l/min x bar hp = gpm x psi 6 1714 Shaft Torque (M) N-m = bar x cm 3 /r lb-in = psi x in 3 /r 62.8 6.28 Shaft Speed (n) Efficiencies Volumetric Nv = gpm actual gpm theorectical Mechanical Nm = lb-in actual lb-in theorectical Total Nt = Nv x Nm Q n P M p rpm = 1 x 1/min RPM = 231 x gpm cm 3 /r in 3 /r Output Power (P) kw = N-m x RPM hp = lb-in x rpm 9549 63,25 Volumetric Displacement cm 3 /r = in lpm 3 /r = x 1 gpm x 231 rpm rpm Basic Formulas bar = 1 Newtons/cm 2 gpm = gallons per minute hp = horsepower lb-in = pound inch lb-ft = pound feet kw = kilowatt kgf = kilograms force l/min = liters per minute N-m = Newton meters psi = pounds per square inch rpm = revolutions per minute Commonly Used Conversions To Convert Into Multiply by bar psi 14.5 cm 3 in 3.612 C F ( C x 1.8) +32 gallons (US) liters 3.785 kg lbs 2.25 kgf/cm 2 psi 14.2 kw hp 1.341 liters US Gallons.2642 mm inches.3937 N-m lb-in 8.85 N-m lb-ft.7375 F C ( F-32)/1.8 hp kw.7457 inch mm 2.54 in 3 cm 3 16.39 lb-in N-m.113 lb-ft N-m 1.356 lbs kg.4535 psi bar.6896 psi kgf/cm 2.737 Note: Performance charts can be found on subsequent pages. EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E1 March 214 4
Model Code Selection PVM 45 E R 1 A E 1 AA A 28 A A 1, 2, 3 4, 5, 6 7 8 9, 1 11 12 13, 14 15, 16 17 18, 19 2, 21 22, 23 24 25 26 27 28 1, 2, 3 Product Series PVM M Series Variable Piston Pump 4, 5, 6 Displacement Twelve displacements available 23 bar and 28 bar continuous ratings 7 Valve Plate E Industrial Equipment Speeds 8 Input Rotation R Clockwise (Righthand) L* Counter-clockwise (Lefthand) 9, 1 Input Shaft Standard SAE and ISO splined versions (Other configurations optional) 12 Main Port Location E** End Ported S**** Side Ported 13, 14 Main Port Type SAE & ISO tube ports and 4-bolt flange (Other configurations optional) 15, 16 Pump Special Features None AA Adjustable Maximum Displacement Stop and single shaft (standard) AB Double Shaft Seal, Two Way 17 Control None A Pressure Compensator B Pressure and Flow Compensator with Bleed Orifice C Pressure and Flow Compensator with Plugged Orifice E Industrial Control (57cc through 141 cc only) 18, 19 Pressure Compensator Setting None 7 7 bar (Adjustable between 4 bar and 13 bar) 23 23 bar (Adjustable between 13 bar and 32 bar) 28 28 bar (Adjustable between 13 bar and 32 bar) 22, 23 Torque Limiter Setting None (Not available on M Series) 24 Compensator Special Features None 25 Auxiliary Mounting Pad *** None (Auxiliary mounting available on all frame sizes) 26 Paint No Paint A Standard Blue Paint 27 Customer Identification None (Contact Eaton for Options) 11 Mounting Flange Thirteen options in SAE and ISO mounts 2, 21 Flow Compensator Setting None 11 11 bar setting 2 2-2 bar setting 24 24-24 bar setting 28 Design Code A A (Initial Release) * Not available on 74, 81, 98 and 16 End Port ** Not available on 74, 81, 98 and 16 LH *** Through drive not available on the LH **** Not available on 18 5 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E1 March 214
Model Code Options 4,5,6 Maximum Geometric Displacement Displacement Code 18 2 45 5 57 63 74 81 98 16 131 141 cm 3 /r 18, 21,1 45,1 5, 57,4 63,1 73,7 81, 98,3 16,5 131,1 141, in 3 /r 1.1 1.29 2.75 3.5 3.5 3.85 4.5 4.94 6. 6.5 8. 8.6 9,1 Shaft-End Type at Electric Motor End Shaft Code Description PVM18/2 PVM45/5 PVM57/63 PVM74/81 PVM98/16 PVM131/141 SAE, SAE A, Straight Keyed 1 SAE, SAE 19-1, Straight Keyed 2 SAE, SAE A, 9T Spline 3 SAE, SAE A, 11T Spline 4 SAE, SAE B, Straight Keyed 5 5 SAE, SAE B-B, Straight Keyed 6 6 6 SAE, SAE B, 13T Spline 7 7 7 SAE, SAE B-B, 15T Spline 8 8 8 SAE, SAE C, Straight Keyed 9 9 9 9 SAE, SAE C-C, Straight Keyed 1 1 1 SAE, SAE C, 14T Spline 11 11 11 11 SAE, SAE C-C, 17T Spline 12 12 12 SAE, SAE D, Straight Keyed 13 SAE, SAE D, 13T Spline 14 ISO E2N, Straight Keyed 15 ISO E25N, Straight Keyed, Short Spigot 16 ISO E25N, Straight Keyed 17 17 17 ISO E32N, Straight Keyed, Short Spigot 18 18 18 18 ISO E4N, Straight Keyed, Short Spigot 19 19 19 11 Mounting Flange Specifications Code Description PVM18/2 PVM45/5 PVM57/63 PVM74/81 PVM98/16 PVM131/141 A SAE A, 2-bolt B ISO 8A2HW C SAE B, 2-bolt D ISO 1A2HW E SAE C, 2-bolt F ISO 125-A2HW G SAE C, 4-bolt H ISO 125B4HW J SAE D, 4-bolt K ISO 16B4HW = Available = Not Available EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E1 March 214 6
Model Code Options 13,14 Main Port Options Inlet Code Description Outlet PVM18/2 PVM45/5 PVM57/63 PVM74/81 PVM98/16 PVM131/141 Inlet 2 24 24 1 SAE J1926 (End ports only) Tube Ports Outlet 12 16 16 (End ports only) 2 SAE J518 Inlet 1.25 inch 2. inch 2. inch 2. inch 2.5 inch 2.5 inch Flange Ports Outlet.75 inch 1. inch 1. inch 1. inch 1. inch 1.25 inch* Inlet M42 M48 M48 3 ISO 6149-1 (End ports only) Tube Ports Outlet M27 M33 M33 (End ports only) 4 ISO 6162 Inlet 32mm 51mm 51mm 51mm 64mm 64mm Flange Ports Outlet 19mm 25mm 25mm 25mm 25mm 32mm* British Standard 5 Parallel Pipe Inlet G 1-1/4 G 1-1/2 Tube Ports Outlet G 3/4 G 1 *SAE Code 62, high pressure series, or ISO 4 bar. Other flange ports are SAE Code 61, standard pressure series, or ISO 25-35 bar. 25 Thru-Drive Options Code Description PVM18/2 PVM45/5 PVM57/63 PVM74/81* PVM98/16 PVM131/141 O Single pump, non-thru-drive A SAE A, 2-bolt, 9T spline B SAE A, 2-bolt, 11T spline C SAE B, 2-/4-bolt, 13T spline D SAE B-B, 2-/4-bolt, 15T spline E SAE C, 2-/4-bolt, 14T spline F SAE C-C, 2-/4-bolt, 17T spline G ISO 8-A2HW, 9T SAE spline H ISO 8-A2HW, 11T SAE spline J ISO 1-A2/B4HW, 13T SAE spline K ISO 1-A2/B4HW, 15T SAE spline L ISO 125-A2/B4HW, 14T SAE spline M ISO 125-A2/B4HW, 17T SAE spline = Available = Not Available * Not available on the 74/81 LH 7 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E1 March 214
Specifications and Performance Industrial Displacement, Pressure and Flow Ratings At 5 C (12 F), SAE 1W oil, 1 bar absolute ( psig) inlet Maximum Maximum Flow at 28 bar (4 psi)* Geometric Maximum Pressure bar (psi) l/min (USgpm) Average measured flow rate Displacement @18 @15 @12 @1 Model Series cm /r (in /r) 3 3 Continuous Intermittent* Peak** r/min r/min r/min r/min PVM18 18 (1.1) 28 (4) 32 (46) 35 (5) 31 (8.2) 26 (7) 21 (5.5) 17 (4.5) PVM2 21,1 (1.29) 23 (33) 25 (36) 28 (4) 35 (9) 29 (8) 23 (6) 19 (5) PVM45 45,1 (2.75) 28 (4) 32 (46) 35 (5) 76 (2) 65 (17) 49 (13) 42 (11) PVM5 5, (3.5) 23 (33) 25 (36) 28 (4) 87 (23) 75 (2) 62 (16) 49 (13) PVM57 57,4 (3.5) 28 (4) 32 (46) 35 (5) 12 (27) 85 (22.4) 66 (17.4) 54 (14.3) PVM63 63,1 (3.85) 23 (33) 25 (36) 28 (4) 111 (29) 93 (24) 74 (19) 6 (16) PVM74 73,7 (4.5) 28 (4) 32 (46) 35 (5) 127 (33.5) 16 (28) 86 (22.7) 7 (18.5) PVM81 81, (4.94) 23 (33) 25 (36) 28 (4) 139 (37) 116 (31) 93 (25) 76 (2) PVM98 98,3 (6.) 28 (4) 32 (46) 35 (5) 17 (45) 141 (37) 112 (29.6) 92 (24.3) PVM16 16,5 (6.5) 23 (33) 25 (36) 28 (4) 187 (49) 155 (41) 123 (32) 12 (27) PVM131 131,1 (8.) 28 (4) 32 (46) 35 (5) 215 (57) 178 (47) 141 (37) 118 (31) PVM141 141, (8.6) 23 (33) 25 (36) 28 (4) 238 (63) 199 (53) 158 (42) 131 (35) **Less than 1% of duty cycle. **Momentary system pressure spikes only. Speed, Input Power and Torque Ratings At 5 C (12 F), SAE 1W oil, 1 bar absolute ( psig) inlet Maximum Maximum Torque at Operating 28 bar Approximate Model Speed Maximum Input Power at 28 bar (4 psi) kw (hp)*@88% M.E. (4 psi)* Weight Series r/min @18 r/min @15 r/min @12 r/min @ 1 r/min Nm (lb-ft) kg (lb) PVM18 18 16 (22) 13 (18) 11 (15) 9 (12) 84 (62) 15 (33) PVM2 18 14 (18) 11 (15) 9 (12) 8 (1) 73 (54) 15 (33) PVM45 18 41 (55) 34 (46) 27 (37) 23 (31) 221 (163) 24 (52) PVM5 18 35 (47) 3 (4) 28 (38) 23 (31) 19 (14) 24 (52) PVM57 18 52 (7) 44 (59) 36 (49) 29 (39) 272 (21) 36 (79) PVM63 18 42 (57) 36 (48) 29 (39) 24 (32) 228 (168) 36 (79) PVM74 18 63 (84) 52 (7) 42 (56) 35 (47) 334 (246) 45 (99) PVM81 18 56 (75) 46 (62) 35 (47) 28 (37) 286 (211) 45 (99) PVM98 18 88 (118) 72 (97) 58 (78) 48 (64) 464 (342) 55 (121) PVM16 18 72 (97) 6 (8) 48 (64) 4 (54) 383 (282) 55 (121) PVM131 18 113 (152) 94 (126) 75 (11) 63 (85) 596 (44) 66 (145) PVM141 18 94 (126) 79 (16) 63 (85) 53 (71) 497 (367) 66 (145) Standard Response Times* Model Series On Stroke (msec) Off Stroke (msec) PVM18 3 25 PVM2 39 26 PVM45 14 4 PVM5 14 4 PVM57 65 2 PVM63 85 2 * 33 psi on overbore pumps Standard Response Times* Model Series On Stroke (msec) Off Stroke (msec) PVM74 85 3 PVM81 85 3 PVM98 65 25 PVM16 72 29 PVM131 135 3 PVM141 1 3 *Values with pressure compensator control. EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E1 March 214 8
Specifications and Performance Mobile Displacement, Pressure and Flow Ratings At 93 C (2 F), SAE 1W oil, 1 bar absolute ( psig) inlet Geometric Maximum Pressure bar (psi) Maximum Flow at 28 bar (4 psi) Displacement Flange Ports Tube Ports Model Series cm 3 /r (in 3 /r) Continuous Intermittent* Peak** l/min (USgpm) @ 1 bar inlet l/min (USgpm) @ 1 bar inlet PVM18 18, (1.1) 28 (4) 32 (46) 35 (5) 46 (12) @ 28 r/min 46 (12) @ 28 r/min PVM2 2,1 (1.22) 23 (33) 25 (36) 28 (4) 53 (14) @ 28 r/min 53 (14) @ 28 r/min PVM45 45,1 (2.75) 28 (4) 32 (46) 35 (5) 115 (3) @ 26 r/min 16 (28) @ 24 r/min PVM5 5, (3.5) 23 (33) 25 (36) 28 (4) 125 (33) @ 26 r/min 116 (31) @ 24 r/min PVM57 57,4 (3.5) 28 (4) 32 (46) 35 (5) 14 (37) @ 25 r/min 128 (34) @ 23 r/min PVM63 63,1 (3.85) 23 (33) 25 (36) 28 (4) 15 (4) @ 25 r/min 14 (37) @ 24 r/min PVM74 73,7 (4.5) 28 (4) 32 (46) 35 (5) 163 (43) @ 24 r/min PVM81 81, (4.94) 23 (33) 25 (36) 28 (4) 181 (48) @ 24 r/min PVM98 98,3 (6.) 28 (4) 32 (46) 35 (5) 2 (53) @ 22 r/min PVM16 16,5 (6.5) 23 (33) 25 (36) 28 (4) 222 (59) @ 22 r/min PVM131 131,1 (8.) 28 (4) 32 (46) 35 (5) 233 (62) @ 2 r/min PVM141 141, (8.6) 23 (33) 25 (36) 28 (4) 258 (68) @ 2 r/min **Less than 1% of duty cycle. **Less than.5 second. Standard Response Times* Model Series On Stroke (msec) Off Stroke (msec) PVM18 5 2 PVM2 57 22 PVM45 14 4 PVM5 14 23 PVM57 65 2 PVM63 94 2 Standard Response Times* Model Series On Stroke (msec) Off Stroke (msec) PVM74 95 3 PVM81 135 3 PVM98 85 24 PVM16 9 25 PVM131 1 3 PVM141 128 28 *Values with pressure compensator control. 9 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E1 March 214
Specifications and Performance Mobile Speed, Input Power and Torque Ratings At 93 C (2 F), SAE 1W oil, 1 bar absolute ( psig) inlet Operating Speed and Pressure r/min Max. Input Power at Max. Torque at Approximate 1 bar Inlet,85 bar Inlet Max. Speed and 28 bar 28 bar (4 psi) Weight (dry) Model Series Flange Ports Tube Ports Flange Ports (4 psi) kw (hp) Nm (lb-ft) kg (lbs) 28 r/min 24 (32) PVM18 28 r/min 24 (32) 82 (6) 15 (33) 26 r/min 22 (3) 28 r/min 21 (28) PVM2 28 r/min 21 (28) 72 (53) 15 (33) 26 r/min 2 (27) 26 r/min 56 (75) PVM45 24 r/min 53 (71) 198 (46) 24 (52) 22 r/min 48 (64) 26 r/min 51 (68) PVM5 24 r/min 48 (64) 24 (15) 24 (52) 22 r/min 44 (59) 25 r/min 68 (91) PVM57 23 r/min 62 (83) 262 (193) 36 (79) 21 r/min 56 (75) 25 r/min 59 (79) PVM63 24 r/min 57 (76) 225 (166) 36 (79) 22 r/min 52 (69) PVM74 24 r/min 84 (113) 19 r/min 69 (93) 334 (246) 45 (99) PVM81 24 r/min 69 (93) 19 r/min 55 (74) 276 (24) 45 (99) PVM98 22 r/min 15 (141) 18 r/min 86 (115) 457 (337) 55 (121) PVM16 22 r/min 87 (117) 18 r/min 7 (94) 377 (278) 55 (121) PVM131 2 r/min 122 (164) 16 r/min 98 (131) 581 (429) 66 (145) PVM141 2 r/min 12 (137) 16 r/min 81 (19) 483 (356) 66 (145) EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E1 March 214 1
Control Options Pressure Compensator Control Code A The pump will provide a continuously modulated flow to meet changing load demands at a pre-adjusted compensator pressure. At pressures below the compensator setting, the pump will operate at maximum displacement. See model code on page 4 for compensator pressure ranges. Warning: The pressure compensator may be adjusted beyond the rated pressure of the pump. When adjusting the pressure limiter, install a -35 bar (-5 psi) gage in the outlet gage port and limit the pressure setting to the continuous rated pressure for the pump displacement shown on page 7. F case drain K inlet gage port K outlet gage port B inlet To load See model code on page xx for spring (pressure) adjustment ranges. C outlet Industrial Pressure Cut-off Characteristics of Code A Pressure Compensator Control at 5 C (12 F), static conditions. Q Outlet Flow Change in Pressure A Change in Flow B Outlet Pressure P Pressure Cut-off Characteristics of Pressure Compensator Control @ 5 C (12 F), Static Conditions P Outlet Max. Speed Q Outlet Flow Pressure A B Model Series r/min l/min (USgpm) bar (psi) bar (psi) L/min (USgpm) PVM18 18 32 (8.5) 28 (4) 2,8 (4) 4,5 (1.2) PVM2 18 35 (9.25) 23 (33) 2,8 (4) 4,5 (1.2) PVM45 18 76 (2) 28 (4) 1 (15) 4,5 (1.2) PVM5 18 87 (23) 23 (33) 1 (15) 4,5 (1.2) PVM57 18 12 (27) 28 (4) 3,5 (51) 14 (3.7) PVM63 18 113 (29) 23 (33) 7,4 (17) 7,6 (2.) PVM74 18 127 (33.5) 28 (4) 1,5 (22) 37 (9.8) PVM81 18 141 (37) 23 (33) 1,5 (22) 37 (9.8) PVM98 18 179 (47) 28 (4) 1,5 (22) 25 (6.6) PVM16 18 195 (51.5) 23 (33) 1,5 (22) 2 (5.3) PVM131 18 229 (6.5) 28 (4) 3,5 (51) 19 (5.) PVM141 18 238 (63) 23 (33) 3,5 (51) 14 (3.7) 11 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E1 March 214
Control Options Mobil Pressure Cut-off Characteristics of Pressure Compensator Control at 93 C (2 F), static conditions. Outlet Flow Q Change in Pressure A Change in Flow B Outlet Pressure P Pressure Cut-off Characteristics of Pressure Compensator Control @ 93 C (2 F), Static Conditions P Outlet Rated Speed Q Outlet Flow Pressure A B Model Series r/min l/min (USgpm) bar (psi) bar (psi) L/min (USgpm) PVM18 28 42 (11) 28 (4) 2,8 (4) 4,5 (1.2) PVM2 28 52 (14) 23 (33) 2,8 (41) 4,5 (1.2) PVM45 26 115 (3) 28 (4) 1 (15) 4,5 (1.2) PVM5 26 125 (33) 23 (33) 1 (15) 4,5 (1.2) PVM57 25 14 (37) 28 (4) 3,5 (5) 14 (3.7) PVM63 25 159 (42) 23 (33) 7,4 (17) 11,4 (3.) PVM74 24 174 (46) 28 (4) 1,5 (2) 37 (9.8) PVM81 24 185 (49) 23 (33) 1,5 (22) 37 (9.8) PVM98 22 217 (57) 28 (4) 1,5 (2) 32 (8.4) PVM16 22 234 (62) 23 (33) 1,5 (22) 24 (6.33) PVM131 2 253 (67) 28 (4) 1, (15) 23 (6.) PVM141 2 258 (68) 23 (33) 7, (1) 14 (3.7) EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E1 March 2143 12
Control Options Load Sensing and Pressure Compensator Control Code B or C The pump will provide power matching of pump output to system load demand, maximizing efficiency and improving load metering characteristics of any directional control valve installed between the pump and the load. Load sensing ensures that the pump always provides only the amount of flow needed by the load. At the same time, the pump operating pressure adjusts to the actual load pressure plus a pressure differential required for the control action. When the system is not demanding power, the load sense control will operate in an energy-saving stand-by mode. Typically, the differential pressure is that between the pressure inlet and service port of a proportionally controlled directional valve, or a load sensing directional control valve. See the model code on page 4 for differential pressure settings for load sensing. If the load pressure exceeds the system pressure setting, the pressure compensator de-strokes the pump. The load sensing line must be as short as possible and can also be used for remote control or unloading of the pump pressure. For remote control purposes, it is recommended that you contact your Eaton representative for the correct configuration of the control. Warning: The pressure compensator may be adjusted beyond the rated pressure of the pump. When adjusting the pressure limiter, install a -35 bar (-5 psi) gage in the outlet gage port and limit the pressure setting to the continuous rated pressure for the pump displacement shown on page 7. F case drain K inlet gage port K outlet gage port Optional bleed-down orifice in Code B control.,4 mm (.16 in.) Orifice is plugged for no bleed down in control Code C. B inlet To load C outlet J load sense signal port 13 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E1 March 214
Control Options Industrial Control Compensator Code E & F (Model 57-141 only) This pump is intended for use when multiple, remote, or electronically controlled compensating settings, with or without load sensing, are desired. Pressure compensation is obtained when an internal plug is removed, the load-sense signal port is kept plugged, and internal pilot pressure is applied to the spring chamber of the control spool. For pressure compensation with load sensing, the internal plug stays, the load-sense signal port is unplugged, and pilot pressure is externally applied. An external relief valve (not supplied) controls spring chamber pressure. The externally adjustable spring determines the differential pressure setting of the control. Outlet pressure is limited to the valve of the spring chamber (pressure port) pressure, plus control differential pressure. Spring chamber (pilot) pressure is separated from outlet pressure by an internal orifice. Outlet pressure shifts the spool when pressure drop across the orifice reaches the differential pressure setting, and the pump de-strokes. The relief valve can be mounted to an NFPA-D3/ISO 441-3 pad on the pump control, or remotely located via tapping and blanking plates installed on the pad. See Ordering Procedure, page 27, for more on valves and plates. The standard factory-set differential pressure setting of the pump control is 2 bar (29 psi) and is not specified in the pump model number. Any other ordered differential pressure, within the control s adjustable pressure range of 17-35 bar (247-58 psi), will be specified in the model number. With Pressure & Flow Compensator (E) Inlet To load Inlet To load Outlet Outlet Load sense signal port Pressure Compensating Without Load Sensing (F) Load sense signal port Pressure port Tank port Pressure port Tank port Case drain Case drain EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E1 March 214 14
Performance Industrial PVM18 Typical Noise Levels at 18 and 12 r/min with Petroleum Oil (1W) at 5 C (12 F) and 1. bar absolute ( psi gauge) Inlet 66 64 62 6 18 r/min max. flow Delivery and Efficiency at 18 r/min 5 C (12 F) and 1. bar absolute ( psi gauge) Inlet 1 Volumetric Efficiency 9 Overall Efficiency 8 7 Noise Level dba 58 56 54 52 12 r/min max. flow 5 12 r/min 48 18 r/min min. flow min. flow 46 5 1 15 2 25 3 35 (7) (15) (22) (29) (36) (44) (5) Sound pressure data equivalent to NFPA. Efficiency % 6 5 4 3 2 1 5 (7) Delivery (effective flow) 1 15 2 25 3 35 (15) (22) (29) (36) (44) (5) 4 (11) 3 (8) 2 (5) 1 (3) Delivery l/min (USgpm) Noise Level dba Typical Noise Levels at 15 and 1 r/min with Petroleum Oil (1W) at 5 C (12 F) and 1. bar absolute ( psi gauge) Inlet 62 6 58 56 54 52 5 48 46 44 15 r/min max. flow 1 r/min max. flow 15 r/min min. flow 1 r/min min. flow 42 5 1 15 2 25 3 35 (7) (15) (22) (29) (36) (44) (5) Input Torque Nm (in-lb) Input Torque and Power at 18 r/min 5 C (12 F) and 1. bar absolute ( psi gauge) Inlet 1 (885) 9 (796) 8 (78) 7 (619) 6 (531) 5 (442) 4 (354) 3 (265) 2 (177) Input Torque, Input Power, 2 (27) 15 (2) 1 (13) 1 (88) Input Torque, 5 (7) Cut-off 5 1 15 2 25 3 35 (7) (15)(22)(29)(36)(44)(5) Input Power kw (hp) 15 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E1 March 214
Performance Industrial PVM18 Efficiency % Delivery and Efficiency at 15 r/min 5 C (12 F) and 1. bar absolute ( psi gauge) Inlet 1 Volumetric Efficiency 9 Overall Efficiency 8 7 6 5 4 3 2 1 5 (7) Delivery (effective flow) 3 (8) 2 (5) 1 (3) 1 15 2 25 3 35 (15) (22) (29) (36) (44) (5) Delivery l/min (USgpm) Delivery and Efficiency at 12 r/min 5 C (12 F) and 1. bar absolute ( psi gauge) Inlet 1 Volumetric Efficiency 9 Overall Efficiency 8 Efficiency % 7 6 5 4 3 2 1 5 (7) Delivery (effective flow) 3 (8) 2 (5) 1 (3) 1 15 2 25 3 35 (15) (22) (29) (36) (44) (5) Delivery l/min (USgpm) Input Torque and Power at 15 r/min 5 C (12 F) and 1. bar absolute ( psi gauge) Inlet 1 (885) 9 (796) 8 (78) 7 (619) 6 (531) 5 (442) 4 (354) 3 (265) 2 (177) 1 (88) Input Torque, Input Power, 5 1 15 2 25 3 35 (7) (15) (22) (29) (36) (44) (5) 2 (27) 15 (2) 1 (13) 5 (7) Input Power kw (hp) Input Torque and Power at 12 r/min 5 C (12 F) and 1. bar absolute ( psi gauge) Inlet 1 (885) Input Torque, 9 (796) 8 (78) 7 (619) 6 (531) 5 (442) 4 (354) 3 (265) 2 (177) 1 (88) 2 (27) Input Power, 15 (2) 1 (13) 5 (7) 5 1 15 2 3 (7) (15)(22)(29) (44)(5) 35 25 (36) Input Power kw (hp) EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E1 March 214 16
Performance Industrial PVM18 Efficiency % Delivery and Efficiency at 1 r/min 5 C (12 F) and 1. bar absolute ( psi gauge) Inlet 1 Volumetric Efficiency 9 Overall Efficiency 8 7 6 5 4 3 2 1 5 (7) Delivery (effective flow) 1 15 2 25 (15) (22) (29) (36) 3 (44) 2 (5) 1 (3) 35 (5) Delivery l/min (USgpm) Case Flow Versus Outlet Pressure at 18 r/min, Full Flow 5 C (12 F) and 1. bar absolute ( psi gauge) Inlet 1,4 (.37) Case Flow l/min (USgpm) 1,2 (.32) 1, (.26),8 (.21),6 (.16),4 (.11),2 (.5) 5 1 15 2 25 3 35 (7) (15) (22) (29) (36) (44) (5) Input torque Nm (in.lb.) Input Torque and Power at 1 r/min 5 C (12 F), and 1. bar absolute ( psi gauge) Inlet 1 (885) 9 (796) 8 (78) 7 (619) 6 (531) 5 (442) 4 (354) 3 (265) 2 (177) 1 (88) Input Torque, Input Power, 5 1 15 2 3 (7) (15) (22) (29) (44)(5) 35 25 (36) 2 (27) 15 (2) 1 (13) 5 (7) Input Power kw (hp) Case Flow l/min (USgpm) Case Flow Versus Outlet Pressure at Cutoff, 18 r/min 5 C (12 F) and 1. bar absolute ( psi gauge) Inlet 5 (1.32) 4 (1.6) 3 (.79) 2 (.53) 1 (.26) 5 1 15 2 25 3 35 (7) (15) (22) (29) (36) (44) (5) 17 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E1 March 214
Efficiency % Delivery l/min (USgpm) Performance Mobile PVM18 76 72 Typical Noise Levels Petroleum Oil (1W) at 93 C (2 F), 1. bar absolute ( psi gauge) Inlet (Sound pressure data equivalent to NFPA) 28 r/min Max. Flow Delivery and Case Flow Versus Speed @ 93 C (2 F), full flow and 1. bar absolute ( psi) gauge Inlet 5 (13.2) 45 (11.9) 4 (1.6) 25 bar (365 psi), Delivery Noise Level dba 68 64 6 56 52 48 6 r/min Max. Flow 28 r/min Min. Flow 6 r/min 44 Min. Flow 4 5 1 (7) (15)(22) 15 2 25 3 35 (29) (36) (44)(5) 35 (9.2) 3 (7.9) 25 (5.3) 2 (5.3) 15 (4.) 1 (2.6) 5 (1.3) 25 bar (36 psi), Delivery 25 bar (36 psi), Case flow 25 bar (365 psi), Case flow 5 1 15 2 25 Speed r/min 3 4, (1.1) 3, (.8) 2, (.5) 1, (.3) Case Flow l/min (USgpm) Overall Efficiency Versus Speed at 93 C (2 F) and 1. bar absolute ( psi gauge) Inlet 95 9 1 bar (15 psi) 85 15 bar (22 psi) 2 bar 8 (29 psi) 25 bar (36 psi) 75 28 bar (4 psi) 32 bar (46 psi) 7 5 1 15 2 25 3 Speed r/min Input Torque Versus Speed @ 93 C (2 F), full flow and 1. bar absolute ( psi gauge) inlet 11 (973) 1 (885) 9 (796) 8 (78) 7 (619) 6 (531) 5 (442) 4 (354) 3 (265) 2 (177) 1 (88) 32 bar (46 psi) 28 bar (4 psi) 25 bar (36 psi) 2 bar (29 psi) 15 bar (22 psi) 1 bar (15 psi) 25 bar (365 psi) 5 1 15 2 25 Speed r/min 3 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E1 March 214 18
Input Torque - Nm (in.lb.) Case Flow (l/min (USgpm) Performance Mobile PVM18 Input Power @ Full Flow kw (hp) Input Power Versus Speed @ 93 C (2 F), full flow and 1. bar absolute ( psi gauge) inlet 28 (37.5) 32 bar 26 (34.9) (46 psi) 24 (32.2) 28 bar (4 psi) 22 (29.5) 25 bar 2 (26.8) (36 psi) 18 (24.1) 2 bar 16 (21.4) (29 psi) 14 (18.8) 15 bar 12 (16.1) (22 psi) 1 (13.4) 1 bar 8 (1.7) (15 psi) 6 (8.) 4 (5.4) 25 bar 2 (2.7) (365 psi) 5 1 15 2 Speed r/min 25 3 3 (27) @ 93 C (2 F), load sense standby and 1. bar absolute ( psi gauge) inlet 2 (18) 2 bar (3 psi) differential, Input Torque 2 bar (3 psi) differential, 1 (9) Case Flow 5 (1.32) 11 bar (16 psi) 4 (1.6) differential, 3 (.79) Input Torque 11 bar (16 psi) differential, 2 (.53) Case Flow 1 (.26) 5 1 15 2 25 3 Speed r/min Input Torque and Case Flow Versus Speed @ 93 C (2 F), cut-off and 1. bar absolute ( psi gauge) inlet 5 (442) 45 (398) 28 bar (4 psi) Input Torque 4 (354) 35 (31) 3 (265) 25 (221) 15 bar (22 psi) 2 (177) Input Torque 15 (135) 9 (2.4) 28 bar (4 psi), Case Flow 1 (88) 6 (1.6) 5 (45) 15 bar (22 psi) 3 (.8) Case Flow 5 1 15 2 25 Speed r/min 19 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E1 March 214
Performance Industrial PVM2 Noise Level dba 64 62 6 58 56 54 Typical Noise Levels at 18 and 12 r/min with Petroleum Oil (1W) at 5 C (12 F) and 1. bar absolute ( psi gauge) Inlet 18 r/min Max. Flow 12 r/min Max. Flow 52 5 18 r/min Min. Flow 48 46 44 42 4 5 1 15 12 r/min Min. Flow 2 (7) (15) (22) (29) 25 (36) Efficiency % Delivery and Efficiency at 18 r/min, 5 C (12 F), and 1. bar absolute ( psi gauge) Inlet 1 Volumetric Efficiency 9 Overall Efficiency 8 7 6 5 4 3 2 1 Delivery (effective flow) 5 1 15 2 (7) (15) (22) (29) 5 (13) 4 (11) 3 (8) 2 (5) 1 (3) 25 (36) Delivery l/min (USgpm) Noise Level dba Typical Noise Levels at 15 and 1 r/min with Petroleum Oil (1W) at 5 C (12 F) and 1. bar absolute ( psi gauge) Inlet 64 62 15 r/min 6 Max. Flow 58 56 54 1 r/min Max. Flow 52 5 48 15 r/min Min. Flow 46 44 1 r/min Min. Flow 42 4 5 (7) 1 (15) 15 (22) 2 (29) Sound pressure data equivalent to NFPA 25 (36) Input torque Nm (in.lb.) Input Torque and Power at 18 r/min, 5 C (12 F), and 1. bar absolute ( psi gauge) Inlet 12 (162) 11 (973) 1 (885) 9 (796) 8 (78) 7 (619) 6 (531) 5 (442) 4 (354) 3 (265) 2 (177) 1 (88) Input Torque, Input Power, Input Torque, Cut off 5 (7) 1 (15) 15 (22) 2 (29) 5 (7) 25 (36) 25 (34) 2 (27) 15 (2) 1 (13) Input Power kw (hp) EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E1 March 214 2
Performance Industrial PVM2 Efficiency % Delivery and Efficiency at 15 r/min, 5 C (12 F), and 1. bar absolute ( psi gauge) Inlet 1 Volumetric Efficiency 9 Overall Efficiency 8 7 6 5 4 3 2 1 Delivery (effective flow) 5 1 15 2 (7) (15) (22) (29) 5 (13) 4 (11) 3 (8) 2 (5) 1 (3) 25 (36) Delivery l/min (USgpm) Efficiency % Delivery and Efficiency at 12 r/min, 5 C (12 F), and 1. bar absolute ( psi gauge) Inlet 1 Volumetric Efficiency 9 Overall Efficiency 8 7 6 5 4 3 2 1 5 (7) Delivery (effective flow) 1 (15) 15 (22) 2 (29) 25 (36) 5 (13) 4 (11) 3 (8) 2 (5) 1 (3) Delivery l/min (USgpm) Input torque Nm (in.lb.) Input Torque and Power at 15 r/min, 5 C (12 F), and 1. bar absolute ( psi gauge) Inlet 12 (162) 11 (973) 1 (885) 9 (796) 8 (78) 7 (619) 6 (531) 5 (442) 4 (354) 3 (265) 2 (177) 1 (88) Input Torque, 5 1 (7) (15) Input Power, 15 (22) 2 (29) 25 (34) 2 (27) 15 (2) 1 (13) 5 (7) 25 (36) Input Power kw (hp) Input torque Nm (in.lb.) Input Torque and Power at 12 r/min, 5 C (12 F), and 1. bar absolute ( psi gauge) Inlet 12 (162) 11 (973) 1 (885) 9 (796) 8 (78) 7 (619) 6 (531) 5 (442) 4 (354) 3 (265) 2 (177) 1 (88) Input Torque, 5 1 (7) (15) Input Power, 15 (22) 2 (29) 25 (34) 2 (27) 15 (2) 1 (13) 5 (7) 25 (36) Input Power kw (hp) 21 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E1 March 214
Performance Industrial PVM2 Efficiency % Delivery and Efficiency at 1 r/min, 5 C (12 F), and 1. bar absolute ( psi gauge) Inlet 1 9 8 7 6 5 4 3 2 1 Volumetric Efficiency 5 (7) 1 (15) Overall Efficiency Delivery (effective flow) 15 (22) 2 (29) 5 (13) 4 (11) 3 (8) 2 (5) 1 (3) 25 (36) Delivery l/min (USgpm) Case Flow l/min (USgpm) Case Flow versus Outlet Pressure at 18 r/min, Full Flow, 5 C (12 F), and 1. bar absolute ( psi gauge) Inlet 2.5 (.66) 2.3 (.59) 2. (.53) 1.8 (.46) 1.5 (.4) 1.3 (.33) 1. (.26).8 (.2).5 (.13).3 (.7) 5 (7) 1 (15) 15 (22) 2 (29) 25 (36) Input torque Nm (in.lb.) Input Torque and Power at 1 r/min, 5 C (12 F), and 1. bar absolute ( psi gauge) Inlet 12 (162) 11 (973) 1 (885) 9 (796) 8 (78) 7 (619) 6 (531) 5 (442) 4 (354) 3 (265) 2 (177) 1 (88) Input Torque, 5 1 (7) (15) Input Power, 15 (22) 2 (29) 25 (34) 2 (27) 15 (2) 1 (13) 5 (7) 25 (36) Input Power kw (hp) Case Flow l/min (USgpm) 1 (2.64) Case Flow versus Outlet Pressure at Cutoff, 18 r/min, 5 C (12 F), and 1. bar absolute ( psi gauge) Inlet 9 (2.38) 8 (2.11) 7 (1.85) 6 (1.59) 5 (1.32) 4 (1.6) 3 (.79) 2 (.53) 1 (.26) 5 1 15 2 (7) (15) (22) (29) 25 (36) EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E1 March 214 22
Performance Mobile PVM2 Typical Noise Levels at 28 & 6 r/min with Petroleum Oil (1W) at 93 C (2 F) and 1. bar absolute ( psi gauge) Inlet Noise Level dba 77 74 71 68 65 62 59 56 53 5 47 44 41 28 r/min max. flow 6 r/min max. flow 28 r/min min. flow 6 r/min min. flow 5 1 15 2 (7) (15) (22) (29) Sound pressure data equivalent to NFPA. 25 (36) Overall Efficiency (%) Overall Efficiency versus Speed at 93 C (2 F) and 1. bar absolute ( psi gauge) inlet 1 95 9 85 8 75 7 65 6 55 5 15 bar (22 psi) 21 bar (3 psi) 5 bar (7 psi) 23 bar (33 psi) 1 bar (15 psi) 5 1 15 2 25 Speed r/min 3 Delivery l/min (USgpm) Delivery and Case Flow versus Speed at 93 C (2 F), Full Flow 1. bar absolute ( psi gauge) inlet 6 (15.9) 55 (14.5) 5 (13.2) 45 (11.9) 4 (1.6) 35 (9.2) 3 (7.9) 25 (6.6) 2 (5.3) 15 (4.) 1 (2.6) 5 (1.3) 5 bar (725 psi) Delivery 5 1 15 2 25 Speed (r/min) 21 bar (3 psi) Delivery 21 bar (3 psi) Case Flow 5 bar (725 psi) Case Flow Case Flow l/min (USgpm) 4 (1.6) 3 (.79) 2 (.53) 1 (.26) 3 23 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E1 March 214
Input Torque Nm (lb.in.) Input put Power Power kw kw (hp) (hp) Performance Mobile PVM2 Input Torque versus Speed at 93 C (2 F), Full Flow and 1. bar absolute ( psi gauge) Inlet Input Power versus Speed at 93 C (2 F), Full Flow and 1. bar absolute ( psi gauge) Inlet 11 (973) 1 (885) 9 (796) 8 (78) 7 (619) 6 (531) 5 (442) 4 (354) 3 (265) 2 (177) 1 (88) 21 bar (3 psi) 5 1 15 2 23 bar (33 psi) 15 bar (22 psi) 1 bar (15 psi) 5 bar (725 psi) Speed (r/min) 25 3 24 (32) 22 (3) 2 (27) 18 (24) 16 (21) 14 (19) 12 (16) 1 (13) 8 (11) 6 (8) 4 (5) 2 (3) 23 bar (33 psi) 5 1 15 2 Speed (r/min) 25 21 bar (3 psi) 15 bar (22 psi) 1 bar (15 psi) 5 bar (725 psi) 3 Input Torque Nm (lb.in.) Input Torque and Case Flow versus Speed at 93 C (2 F), Load Sense Standby and 1. bar absolute ( psi gauge) Inlet 3.2 (28) 3. (27) 2.8 (25) 2.6 (23) 2.4 (21) 2.2 (19) 2 (18) 1.8 (16) 1.6 (14) 1.4 (12) 1.2 (11) 1 (9).8 (7).6 (5).4 (4).2 (2) 2 bar (29 psi) diff. Input Torque 11 bar (16 psi) diff. Input Torque 11 bar (16 psi) diff. Case Flow 2 bar (29 psi) diff. Case Flow 5 1 15 2 25 Speed (r/min) Case Flow l/min (USgpm) 5. (1.32) 4. (1.6) 3. (.79) 2. (.53) 1. (.26) 3 Input Torque and Case Flow versus Speed at 93 C (2 F), Pressure Limit Cut-off and 1. bar absolute ( psi gauge) Inlet 3 (265) 24 (212) 21 (186) 18 (159) 15 (133) 12 (16) 9 (8) Input Torque Nm (lb.in.)27 (239) 6 (53) 3 (27) 15 bar (22 psi) Input Torque 21 bar (3 psi) Input Torque 21 bar (3 psi) Case Flow 15 bar (22 psi) Case Flow 5 1 15 2 25 3 Speed (r/min) Case Flow l/min (USgpm) 9 (2.4) 6 (1.6) 3 (.8) EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E1 March 214 24
Performance Industrial PVM45 Noise Level dba 72 7 68 66 64 62 6 Typical Noise Levels at 18 and 12 r/min with Petroleum Oil (1W) at 5 C (12 F) and 1. bar absolute ( psi gauge) Inlet 18 r/min Max. Flow 18 r/min Min. Flow 58 12 r/min Max. Flow 56 54 12 r/min Min. Flow 52 5 48 5 1 15 2 25 (7) (15) (22) (29) (36) Sound pressure data equivalent to NFPA 3 (44) Efficiency % Delivery and Efficiency at 18 r/min 5 C (12 F) and 1. bar absolute ( psi gauge) Inlet 1 Volumetric Efficiency 9 Overall Efficiency 8 7 6 5 4 3 2 1 5 (7) Delivery (effective flow) 1 (15)(22) 15 2 25 3 35 (29) (36) (44) (5) 12 (27) 76 (2) 49 (13) 27 (7) Delivery l/min (USgpm) Noise Level dba 72 7 68 66 64 62 6 58 56 54 Typical Noise Levels at 15 and 1 r/min with Petroleum Oil (1W) at 5 C (12 F) and 1. bar absolute ( psi gauge) Inlet 15 r/min Max. Flow 1 r/min Min. Flow 52 5 1 15 2 25 (7) (15) (22) (29) (36) 15 r/min Min. Flow 1 r/min Max. Flow 3 (44) Input torque Nm (in.lb.) Input Torque and Power at 18 r/min 5 C (12 F) and 1. bar absolute ( psi gauge) Inlet 24 (2125) 21 (186) 18 (1595) 15 (1325) 12 (16) 9 (795) 6 (53) 3 (265) Input Torque, Input Power, Input Torque, Cut-off 5 1 15 2 25 3 35 (7) (15) (22) (29) (36) (44) (5) 5 (67) 4 (54) 3 (4) 2 (27) 1 (13) Input Power kw (hp) 25 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E1 March 214
Input Power kw (hp) Performance Industrial PVM45 Delivery and Efficiency at 15 r/min 5 C (12 F) and 1. bar absolute ( psi gauge) Inlet 1 Volumetric Efficiency 9 Overall Efficiency 8 Delivery and Efficiency at 12 r/min 5 C (12 F) and 1. bar absolute ( psi gauge) Inlet 1 Volumetric Efficiency 9 Overall Efficiency 8 Efficiency % 7 6 5 4 3 2 1 5 (7) Delivery (effective flow) 1 15 2 25 3 35 (15) (22) (29)(36) (44) (5) 12 (27) 76 (2) 49 (13) 27 (7) Delivery l/min (USgpm) Efficiency % 7 6 5 4 3 2 Delivery (effective flow) 76 (2) 57 (15) 38 (1) 1 19 (5) 5 1 15 2 25 3 (7) (15) (22) (29) (36) (44)(5) 35 Delivery l/min (USgpm) Input Torque and Power at 15 r/min 5 C (12 F) and 1. bar absolute ( psi gauge) Inlet 24 (2125) Input Torque and Power at 12 r/min 5 C (12 F) and 1. bar absolute ( psi gauge) Inlet 24 (2125) Input torque Nm (in.lb.) 21 (186) 18 (1595) 15 (1325) 12 (16) 9 (795) 6 (53) 3 (265) Input Torque, Input Power, 5 1 15 2 25 3 35 (7) (15) (22) (29) (36) (44) (5) 4 (54) 3 (4) 2 (27) 1 (13) Input Power kw (hp) 21 (186) 18 (1595) 15 (1325) 12 (16) 9 (795) 6 (53) 3 (265) Input Torque, Input Power, 3 (4) 2 (27) 1 (13) 5 1 15 2 25 3 35 (7) (15) (22) (29) (36)(44) (5) EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E1 March 214 26
Case Flow l/min (USgpm) Case Flow l/min (USgpm) Performance Industrial PVM45 Efficiency % Delivery and Efficiency at 1 r/min 5 C (12 F) and 1. bar absolute ( psi gauge) Inlet 1 9 8 7 6 5 4 3 2 1 5 (7) Overall Efficiency Volumetric Efficiency Delivery (effective flow) 1 15 2 25 3 35 (15) (22) (29) (36) (44) (5) 76 (2) 57 (15) 38 (1) 19 (5) Delivery l/min (USgpm) Case Flow Versus Outlet Pressure at 18 r/min, Full Flow 5 C (12 F) and 1. bar absolute ( psi gauge) Inlet 2, (.53) 1,8 (.47) 1,6 (.42) 1,4 (.37) 1,2 (.32) 1, (.26),8 (.21),6 (.16),4 (.1),2 (.5) 5 1 15 2 25 3 35 (7) (15) (22) (29) (36) (44)(5) Input Torque and Power at 1 r/min 5 C (12 F), and 1. bar absolute ( psi gauge) Inlet 24 (2125) Case Flow Versus Outlet Pressure at Cutoff, 18 r/min 5 C (12 F) and 1. bar absolute ( psi gauge) Inlet 6 (1.59) 21 (186) 18 (1595) 15 (1325) 12 (16) 9 (795) 6 (53) 3 (265) Input Torque, Input Power, 5 1 15 2 25 3 35 (7) (15) (22) (29) (36) (44) (5) 3 (4) 2 (27) 1 (13) Input Power kw (hp) 5 (1.32) 4 (1.6) 3 (.79) 2 (.53) 1 (.26) 5 1 15 2 25 3 35 (7) (15) (22) (29)(36) (44)(5) 27 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E1 March 214
Delivery l/min (USgpm) Case Flow l/min (USgpm) Performance Mobile PVM45 Noise Level dba 82 78 74 7 66 62 58 54 Typical Noise Levels Petroleum Oil (1W) at 93 C (2 F), 1. bar absolute ( psi gauge) Inlet (Sound pressure data equivalent to NFPA) 26 r/min Max. Flow 26 r/min Min. Flow 6 r/min Min. Flow 6 r/min Max. Flow 5 5 1 15 2 25 (7) (15) (22) (29) (36) 3 (44) Delivery and Case Flow Versus Speed @ 93 C (2 F), full flow and 1. bar absolute ( psi) gauge Inlet 12 (32) 11 (29) 1 (26) 9 (24) 8 (21) 7 (18) 6 (16) 5 (13) 4 (11) 3 (8) 5 bar (7 psi), Delivery 28 bar (4 psi), Delivery 28 bar (4 psi), Case flow 2,5 (.7) 2, (.5) 1,5 (.4) 2 (5) 1, (.3) 5 bar (7 psi), 1 (3) Case flow,5 (.1) 5 1 15 2 25 3 Speed r/min Efficiency % Overall Efficiency Versus Speed at 93 C (2 F) and 1. bar absolute ( psi gauge) Inlet 95 9 85 8 75 1 bar (15 psi) 15 bar (22 psi) 2 bar (29 psi) 25 bar (36 psi) 28 bar (4 psi) 5 bar (7 psi) 17 bar (25 psi) 7 5 1 15 2 25 3 Speed r/min Input Torque Versus Speed @ 93 C (2 F), full flow and 1. bar absolute ( psi gauge) inlet 225 (1991) 21 (1858) 28 bar (4 psi) 195 (1726) 18 (1593) 165 (146) 15 (1327) 135 (1195) 12 (162) 15 (929) 9 (796) 25 bar (36 psi) 2 bar (29 psi) 15 bar (22 psi) 1 bar (15 psi) 75 (664) 6 (531) 5 bar (7 psi) 45 (398) 25 bar (365 psi) 3 (265) 17 bar (25 psi) 5 1 15 2 25 3 Speed r/min EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E1 March 214 28
Performance Mobile PVM45 Input Power @ Full Flow kw (hp) Input Power Versus Speed 93 C (2 F), 1. bar absolute ( psi gauge) Inlet 56 (75) 28 (4) 52 (7) 25 (36) 48 (64) 44 (59) 4 (54) 2 (29) 36 (48) 32 (43) 15 (22) 28 (38) 24 (32) 1 (15) 2 (27) 16 (21) 12 (16) 5 (7) 8 (11) 25 (365) 4 (5) 17 (25) 5 1 15 2 25 3 Speed r/min 1.Case Flow at 26 r/min, Full Flow Pressure bar (psi) Case Flow l/min (USgpm) 1.Case Flow at 26 r/min, Full Flow 93 C (2 F), 1. bar absolute ( psi gauge) Inlet 6 (1.6) 5 (1.3) 4 (1.1) 3 (.8) 2 (.5) 1 (.3) 5 1 15 2 25 3 35 (7) (15) (22) (29)(36) (44) (5) Case Flow l/min (USgpm) 42 (11.1) 38 (1.) 34 (9.) 3 (7.9) 26 (6.9) 22 (5.8) 18 (4.8) 14 (3.7) 1 (2.6) Case Flow at Cutoff at 26 r/min 93 C (2 F), 1. bar absolute ( psi gauge) Inlet 5 1 15 2 25 3 (7) (15) (22) (29) (36) (44) 35 (5) 29 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E1 March 214
Input Torque Nm (in-lb) Efficiency % Delivery l/min (USgpm) Performance Industrial PVM5 Noise Level dba Typical Noise Levels at 18 and 12 r/min with Petroleum Oil (1W) at 5 C (12 F) and 1. bar absolute ( psi gauge) Inlet 72 68 64 6 56 52 48 44 18 r/min max. flow 12 r/min max. flow 18 r/min min. flow 5 (7) 1 (15) 15 (22) 12 r/min min. flow 2 (29) 25 (36) Delivery and Efficiency at 18 r/min, 5 C (12 F), and 1. bar absolute ( psi gauge) Inlet 1 9 8 7 6 5 4 3 2 1 Volumetric Efficiency Overall Efficiency Delivery (effective flow) 5 1 15 2 (7) (15) (22) (29) 25 (36) 125 (33) 1 (26) 75 (2) 5 (13) 25 (7) Noise Level dba Typical Noise Levels at 15 and 1 r/min with Petroleum Oil (1W) at 5 C (12 F) and 1. bar absolute ( psi gauge) Inlet 72 68 64 6 56 52 48 44 15 r/min max. flow 5 (7) 15 r/min min. flow 1 (15) 1 r/min 1 r/min min. flow 15 (22) max. flow Sound pressure data 2 (29) 25 (36) Input Torque and Power at 18 r/min, 5 C (12 F), and 1. bar absolute ( psi gauge) Inlet 24 (2124) 22 (1947) 2 (177) 18 (1593) 16 (1416) 14 (1239) 12 (162) 1 (885) 8 (78) 6 (531) 4 (354) 2 (177) Input Torque, 5 1 (7) (15) Input Power, 15 (22) Input Torque, Cut-off 2 (29) 25 (36) 5 (67) 4 (54) 3 (4) 2 (27) 1 (13) Input Power kw (hp) EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E1 March 214 3
Efficiency % Performance Industrial PVM5 Delivery and Efficiency at 15 r/min, 5 C (12 F), and 1. bar absolute ( psi gauge) Inlet 1 9 8 7 6 5 4 3 2 1 Volumetric Efficiency 5 (7) 1 (15) Overall Efficiency Delivery (effective flow) 15 (22) 2 (29) 25 (36) 125 (33) 1 (26) 75 (2) 5 (13) 25 (7) Delivery l/min (USgpm) Delivery and Efficiency at 12 r/min, 5 C (12 F), and 1. bar absolute ( psi gauge) Inlet 1 Volumetric Efficiency 9 Overall Efficiency 8 Efficiency % 7 6 5 4 3 2 1 Delivery (effective flow) 5 1 15 2 (7) (15) (22) (29) 25 (36) 125 (33) 1 (26) 75 (2) 5 (13) 25 (7) Delivery l/min (USgpm) Input Torque Nm (in-lb) Input Torque and Power at 15 r/min, 5 C (12 F), and 1. bar absolute ( psi gauge) Inlet 24 (2124) 22 (1947) 2 (177) 18 (1593) 16 (1416) 14 (1239) 12 (162) 1 (885) 8 (78) 6 (531) 4 (354) 2 (177) 5 1 (7) (15) Input Torque, Input Power, 15 (22) 2 (29) 25 (36) 5 (67) 4 (54) 3 (4) 2 (27) 1 (13) Input Power kw (hp) Input Torque and Power at 12 r/min, 5 C (12 F), and 1. bar absolute ( psi gauge) Inlet 24 (2124) 22 (1947) 2 (177) 18 (1593) 16 (1416) 14 (1239) 12 (162) 1 (885) 8 (78) 6 (531) 4 (354) 2 (177) 5 1 (7) (15) Input Torque, Input Power, 15 (22) 2 (29) 25 (36) 5 (67) 4 (54) 3 (4) 2 (27) 1 (13) Input Power kw (hp) 31 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E1 March 214
Case Flow l/min (USgpm) Case Flow l/min (USgpm) Performance Industrial PVM5 Delivery and Efficiency at 1 r/min, 5 C (12 F), and 1. bar absolute ( psi gauge) Inlet 1 9 8 Volumetric Efficiency Overall Efficiency Case Flow versus Outlet Pressure at 18 r/min, Full Flow, 5 C (12 F), and 1. bar absolute ( psi gauge) Inlet 1. (.26).9 (.24).8 (.21) 7.7 (.18) Efficiency % 6 5 4 3 2 1 5 (7) Delivery (effective flow) 1 (15) 15 (22) 2 (29) 25 (36) 125 (33) 1 (26) 75 (2) 5 (13) 25 (7) Delivery l/min (USgpm).6 (.16).5 (.13).4 (.11).3 (.8).2 (.5).1 (.3) 5 (7) 1 (15) 15 (22) 2 (29) 25 (36) Input Torque and Power at 1 r/min, 5 C (12 F), and 1. bar absolute ( psi gauge) Inlet 24 (2124) Case Flow versus Outlet Pressure at Cutoff, 18 r/min, 5 C (12 F), and 1. bar absolute ( psi gauge) Inlet 1 (2.64) 22 (1947) 2 (177) 18 (1593) 16 (1416) 14 (1239) 12 (162) 1 (885) 8 (78) 6 (531) 4 (354) 2 (177) Input Torque, Input Power, 5 1 15 2 25 (7) (15) (22) (29) (36) 5 (67) 4 (54) 3 (4) 2 (27) 1 (13) Input Power kw (hp) 9 (2.38) 8 (2.11) 7 (1.85) 6 (1.59) 5 (1.32) 4 (1.6) 3 (.79) 2 (.53) 1 (.26) 5 1 15 2 (7) (15) (22) (29) 25 (36) EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E1 March 214 32
Overall Efficiency (%) Noise Level dba Performance Mobile PVM5 88 86 84 82 8 78 76 74 72 7 68 66 64 Typical Noise Levels at 26 & 6 r/min with Petroleum Oil (1W) at 93 C (2 F) and 1. bar absolute ( psi gauge) inlet 26 r/min max. flow 6 r/min min. flow 26 r/min min. flow 5 1 15 2 (7) (15) (22) (29) Sound pressure data equivalent to NFPA. 6 r/min max. flow 25 (36) 1 Overall Efficiency versus Speed at 93 C (2 F) and 1. bar absolute ( psi gauge) inlet 95 9 85 8 75 7 65 6 55 5 1 bar (15 psi) 2 bar (29 psi) 21 bar (3 psi) 23 bar (33 psi) 5 1 15 2 25 Speed (r/min) 3 Delivery l/min (USgpm) Delivery and Case Flow versus Speed at 93 C (2 F), Full Flow and 1. bar absolute ( psi gauge) inlet 14 (37) 13 (34) 12 (32) 11 (29) 1 (26) 9 (24) 8 (21) 7 (18) 6 (16) 5 (13) 4 (11) 3 (8) 2 (5) 1 (3) 5 bar (725 psi) Delivery 21 bar (3 psi) Delivery 21 bar (3 psi) Case Flow Speed (r/min) Case Flow l/min (USgpm) 5 (1.32) 4 (1.6) 3 (.79) 5 bar (725 psi) 2 (.53) Case Flow 1 (.26) 5 1 15 2 25 3 33 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E1 March 214
Performance Mobile PVM5 Input Torque versus Speed at 93 C (2 F), Full Flow and 1. bar absolute ( psi gauge) Inlet Input Power versus Speed at 93 C (2 F), Full Flow and 1. bar absolute ( psi gauge) Inlet 3 (2655) 6 (8) 275 (2434) 25 (2212) 225 (1991) 2 (177) 175 (1549) 15 (1327) 125 (116) 1 (885) 75 (664) 5 (442) 25 (221) 21 bar (3 psi) 23 bar (33 psi) 2 bar (29 psi) 5 1 15 2 Speed (r/min) 1 bar (15 psi) 17 bar (25 psi) 25 3 Input Power kw (hp) 55 (74) 5 (67) 45 (6) 4 (54) 35 (47) 3 (4) 25 (34) 2 (27) 15 (2) 1 (13) 5 (7) 5 1 15 2 Speed (r/min) 25 23 bar (33 psi) 21 bar (3 psi) 2 bar (29 psi) 1 bar (15 psi) 17 bar (25 psi) 3 Input Torque and Case Flow versus Speed at 93 C (2 F), Load Sense Standby and 1. bar absolute ( psi gauge) Inlet 8 (71) 7 (62) 6 (53) 5 (44) 4 (35) 3 (27) 2 (18) 1 (9) 2 bar (3 psi) diff. Input Torque 11 bar (16 psi) diff. Input Torque 2 bar (3 psi) diff. Case Flow 11 bar (16 psi) diff.case Flow 5 1 15 2 25 Speed (r/min) 3 Case Flow l/min (USgpm 5. (1.32) 4. (1.6) 3. (.79) 2. (.53) 1. (.26) Input Torque and Case Flow versus Speed at 93 C (2 F), Pressure Limit Cut-off and 1. bar absolute ( psi gauge) Inlet 55 (487) 5 (442) 45 (398) 21 bar (3 psi) Input Torque 4 (354) 21 bar 35 (31) (3 psi) 3 (265) Case Flow Case Flow l/min 25 (221) (USgpm) 2 (177) 12 (3.2) 15 (133) 15 bar (22 psi) Input Torque 9 (2.4) 1 (88) 6 (1.6) 5 (44) 15 bar (22 psi) Case Flow 3 (.8) 5 1 15 2 25 3 Speed (r/min) EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E1 March 214 34
Input Power kw (hp) Performance Industrial PVM57 Noise Level dba 74 7 66 62 58 54 Typical Noise Levels at 18 and 12 r/min with Petroleum Oil (1W) at 5 C (12 F) and 1. bar absolute ( psi gauge) Inlet 18 r/min Max. Flow 5 (7) 1 (15) (Sound pressure data equivalent to NFPA) 15 (22) 2 (29) 18 r/min Min. Flow 12 r/min Max. Flow 12 r/min Min. Flow 25 (36) 3 (44) Efficiency % Delivery and Efficiency at 18 r/min 5 C (12 F) and 1. bar absolute ( psi gauge) Inlet 1 Volumetric Efficiency 9 Overall Efficiency 8 7 6 5 4 3 2 1 5 (7) Delivery (effective flow) 1 15 2 25 3 (15) (22) (29) (36) (44)(5) 35 13 (34) 14 (28) 78 (21) 52 (14) 26 (7) Delivery l/min (USgpm) 7 Typical Noise Levels at 15 and 1 r/min with Petroleum Oil (1W) at 5 C (12 F) and 1. bar absolute ( psi gauge) Inlet Input Torque and Power at 18 r/min 5 C (12 F) and 1. bar absolute ( psi gauge) Inlet 3 (2655) Noise Level dba 66 62 58 15 r/min Max. Flow 15 r/min Min. Flow 1 r/min Max. Flow 1 r/min Min. Flow 27 (239) 24 (2124) 21 (1859) 18 (1593) 15 (1328) 12 (162) 9 (797) 6 (531) Input Torque, 6 (8) 5 (67) Input Power, 4 (54) 3 (4) 2 (27) 54 5 (7) 1 15 2 25 3 (15) (22) (29) (36) (44) 3 (266) Input Torque, 1 (13) Cut-off 5 1 15 2 25 3 35 (7) (15) (22) (29) (36) (44)(5) 35 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E1 March 214
Delivery l/min (USgpm) Input Power kw (hp) Performance Industrial PVM57 Delivery and Efficiency at 15 r/min 5 C (12 F) and 1. bar absolute ( psi gauge) Inlet 1 Volumetric Efficiency 9 Overall Efficiency 8 7 Delivery and Efficiency at 12 r/min 5 C (12 F) and 1. bar absolute ( psi gauge) Inlet 1 Volumetric Efficiency 9 Overall Efficiency 8 7 Efficiency % 6 5 4 3 2 1 5 (7) Delivery (effective flow) 1 15 2 25 3 35 (15) (22) (29) (36) (44) (5) 1 (26) 8 (21) 6 (16) 4 (11) 2 (5) Efficiency % 6 5 4 3 2 1 5 (7) Delivery (effective flow) 1 15 2 25 3 35 (15) (22) (29) (36) (44)(5) 1 (26) 8 (21) 6 (16) 4 (11) 2 (5) Delivery l/min (USgpm) Input Torque and Power at 15 r/min 5 C (12 F) and 1. bar absolute ( psi gauge) Inlet 33 (2921) 3 (2655) 27 (239) 24 (2124) 21 (1859) 18 (1593) 15 (1328) 12 (162) 9 (797) 6 (531) 3 (266) Input Torque, Input Power, 5 1 15 2 25 3 35 (7) (15)(22) (29) (36) (44)(5) 6 (8) 5 (67) 4 (54) 3 (4) 2 (27) 1 (13) Input Torque and Power at 12 r/min 5 C (12 F) and 1. bar absolute ( psi gauge) Inlet 33 (2921) 3 (2655) 27 (239) Input Torque, 24 (2124) 21 (1859) 18 (1593) 15 (1328) 12 (162) 9 (797) 6 (531) 3 (266) Input Power, 4 (54) 3 (4) 2 (27) 1 (13) 5 1 15 2 25 3 35 (7) (15) (22) (29) (36) (44) (5) Input Power kw (hp) EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E1 March 214 36
Efficiency % Delivery l/min (USgpm) Input Power kw (hp) Performance Industrial PVM57 Delivery and Efficiency at 1 r/min 5 C (12 F) and 1. bar absolute ( psi gauge) Inlet 1 Volumetric Efficiency 9 Overall Efficiency 8 Case Flow Versus Outlet Pressure at Full Flow, 18 r/min 5 C (12 F) and 1. bar absolute ( psi gauge) Inlet 5 (1.32) 4 (1.6) 7 6 5 4 3 2 1 Delivery (effective flow) 8 (21) 6 (16) 4 (11) 2 (5) Case Flow l/min (USgpm) 3 (.79) 2 (.53) 1 (.26) 5 (7) 1 15 2 25 3 35 (15) (22) (29) (36) (44) (5) 5 1 15 2 25 3 35 (7) (15) (22) (29)(36) (44) (5) Input Torque and Power at 1 r/min 5 C (12 F) and 1. bar absolute ( psi gauge) Inlet 33 (2921) 3 (2655) 27 (239) 24 (2124) 21 (1859) 18 (1593) 15 (1328) 12 (162) 9 (797) Input Torque, Input Power, 6 (531) 3 (266) 5 (7) 1 15 2 25 (15) (22) (29) (36) 3 (44) 4 (54) 3 (4) 2 (27) 1 (13) 35 (5) Case Flow l/min (USgpm) Case Flow Versus Outlet Pressure at Cutoff, 18 r/min 5 C (12 F) and 1. bar absolute ( psi gauge) Inlet 1,1 (.29) 1, (.26),9 (.24),8 (.21),7 (.18),6 (.16),5 (.13) 5 1 15 2 25 3 35 (7) (15) (22) (29) (36) (44)(5) 37 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E1 March 214