LED BUILT-IN MODULES LUGA C 2016 HiCRI 1500 LM TO 4500 LM LUGA C 2016 HiCRI COB MODULES FOR LUMEN PACKAGES FROM 1500 LM UP TO 4500 LM DMC124S**F / DMC125S**F / DMC128S**F Typical Applications Integration in reflector luminaires Shop lighting Furniture lighting Flat surface-mounting luminaires Cladding illumination Stairway and corridor illumination Suspended luminaire with external control gear LUGA C 2016 HiCRI 1500 to 4500 lm LONG SERVICE LIFETIME: 50,000 HOURS (L90; B10) HIGHLY EFFICIENT: UP TO 133 LM/W AT t p =65 C NARROW COLOUR TOLERANCES: 3 STEP MACADAM (INITIAL) 4 STEP MACADAM SHIFT (AFTER 50,000 HRS) HIGH ELECTRICAL ISOLATION DUE TO CERAMIC COB TECHNOLOGY SMALL SHAPE
Technical Notes Dimensions: 19x19x1.7 mm Light emitting surface (LES) DMC124***F / DMC125***F: Ø 11.1 mm DMC128***F: Ø 13.8 mm Use of external LED constant current driver Electrical Characteristics Type Ref. No. Typ. voltage DC Temperature Typ. power consumption 350 ma 500 ma 700 ma 1050 ma coefficient 350 ma 500 ma 700 ma 1050 ma V V V V mv/k W W W W DMC124***F All types 34.8 35.8 18 12.2 17.9 DMC125***F All types 34.2 35.1 36.0 18 12 17.6 25.2 DMC128***F All types 33.2 33.9 34.7 35.7 18 11.6 16.9 24.3 37.5 Voltage and power tolerance: ±10 % Maximum Ratings Exceeding the maximum ratings can lead to reduction of service life or destruction of the modules. Type Operating Operation temperature Ambient temperature Storage temperature Max. allowed current range at t c point range range repetitive peak current ma C min. C max. C min. C max. C min. C max. ma DMC124***F 350 40 +105 40 +40 40 +105 720 500 +96 DMC125***F 350 40 +105 40 +40 40 +105 900 500 +99 700 +81 DMC128***F 500 40 +105 40 +40 40 +105 1440 700 +99 1050 +77 LUGA C 2016 HiCRI 1500 lm to 4500 lm_gb 2/5 January, 2016 Optical Characteristics Type Ref. No. Colour Correlated colour Typ. luminous flux** and efficiency at Typ. Typ. Photometric temperature* 350 ma 500 ma 700 ma 1050 ma beam CRI code K lm lm/w lm lm/w lm lm/w lm lm/w angle ( ) Ra DMC124S27F 560453 warm white 2700 (below BBL) 1190 98 1605 90 120 95 927/349 DMC124S30F 560454 warm white 3000 (below BBL) 1275 105 1715 96 120 95 930/349 DMC124S35F 560455 neutral white 3500 (below BBL) 1355 111 1825 102 120 95 935/349 DMC124S40F 560456 neutral white 4000 (below BBL) 1400 115 1890 106 120 95 940/349 DMC125S27F 560457 warm white 2700 (below BBL) 1195 100 1600 91 2035 81 120 95 927/349 DMC125S30F 560458 warm white 3000 (below BBL) 1280 107 1710 97 2180 87 120 95 930/349 DMC125S35F 560459 neutral white 3500 (below BBL) 1360 113 1825 104 2325 92 120 95 935/349 DMC125S40F 560460 neutral white 4000 (below BBL) 1405 117 1885 107 2405 95 120 95 940/349 DMC128S27F 560461 warm white 2700 (below BBL) 1310 113 1790 106 2370 98 3165 84 120 95 927/349 DMC128S30F 560462 warm white 3000 (below BBL) 1405 121 1920 114 2545 105 3390 90 120 95 930/349 DMC128S35F 560463 neutral white 3500 (below BBL) 1490 128 2040 121 2705 111 3610 96 120 95 935/349 DMC128S40F 560464 neutral white 4000 (below BBL) 1545 133 2115 125 2800 115 3740 100 120 95 940/349 * Colour tolerance: 3 MacAdam ** Production tolerance of luminous flux and efficiency: ± 10 % Min. CRI R a : > 90 Minimum order quantity: 175 pcs. 2
Operating Life Lumen DMC124***F DMC125***F DMC128***F maintenance I F 350 ma I F 500 ma I F 350 ma I F 500 ma I F 700 ma I F 350 ma I F 500 ma I F 700 ma I F 1050 ma L90/B10 51,000 hrs. 41,000 hrs. 54,000 hrs. 44,000 hrs. 26,000 hrs. 61,000 hrs. 55,000 hrs. 44,000 hrs. 22,000 hrs. L80/B10 76,000 hrs. 66,000 hrs. 79,000 hrs. 69,000 hrs. 51,000 hrs. 86,000 hrs. 80,000 hrs. 69,000 hrs. 47,000 hrs. L70/B10 86,000 hrs. 76,000 hrs. 89,000 hrs. 79,000 hrs. 61,000 hrs. 96,000 hrs. 90,000 hrs. 79,000 hrs. 57,000 hrs. Typical Light Distribution Curve I (cd/klm) 85 170 90 60 255 340 30 Mechanical Dimensions The clearance and creepage distances are designed for working voltages up to 235 V DC (basic insulation) and 60 V DC (reinforced insulation). Thickness of PCB is included in calculation. DMC124***F / DMC125***F Ø13.1 LES (Ø11.1) 1±0.1 1.7 TS (Ø1.5) DMC128***F Ø15.8 LES (Ø13.8) 1.7 TS (Ø1.5) 1±0.1 Bins 0.43 0.42 0.41 0.40 0.39 0.38 3000K 2700K LUGA C 2016 HiCRI 1500 lm to 4500 lm_gb 3/5 January, 2016 0.37 0.36 0.35 0.34 3500K 4000K 0.35 0.36 0.37 0.38 0.39 0.40 0.41 0.42 0.43 0.44 0.45 0.46 0.47 0.48 Measurement tolerance x/y: ± 0.005 3
Assembly and Safety Information Installation must be carried out under observation of the relevant regulations and standards. The LED modules are designed for operation within a casing or luminaire. Installation must be carried out in a voltage-free state (i.e. disconnection from the mains). The following advice must be observed; non-observance can result in the destruction of the LED assembly modules, fire and/or other hazards. ESD (electrostatic discharge) protection measures must be observed when handling and installing the LED modules. See VS's application notes on ESD protection. LED assembly modules must not be subjected to any undue mechanical stress, e. g.: do not treat as bulk cargo avoid shear and compressive forces during handling and installation do not damage circuit paths do not touch the yellow phosphorus layer The module must be fixed onto a thermally conductive surface. The electrical connection of the modules must be done with separate holder systems. Direct soldering of cables at the contact pads is not allowed. Safe operation only possible by the use of external constant current sources (I max. see table "Electrical Characteristics"). Operation only with power supply units that feature the following protection: Short-circuit protection Overload protection Overheating protection SELV (Safety Extra Low Voltage); U max. 60 V I max. (see table "Maximum Ratings") must not be exceeded. When operating devices will be selected care has been taken to ensure that the maximum values (see table "Maximum Ratings") will not be exceeded. Please ensure the correct polarity of the leads prior to commissioning. Reversed polarity can destroy the modules. Safety regulations acc. to EN 60598 (or further standards) has to be observed if the maximum output voltage exceed the permitted touchable value. Measurement tolerances: luminous flux: ± 7 % voltage: ± 3 % CRI: ± 1 % A parallel connection of the modules is not allowed. To ensure problem-free operation, the specified maximum temperature at the t c point (see "Operating Life") must be observed (and measured in accordance with EN 60598-1). To satisfy this point, it may be necessary to put measures in place to ensure any heat is dissipated from the PCB to the environment. In the event of outdoor applications or applications in damp locations, care must be taken to protect LED assembly modules against humidity, splashes and jets of water. Any corrosion damage resulting from humidity or contact with condensation will not be recognised as a defect or manufacturing fault. LED assembly modules are not specially protected against foreign bodies or dust. Depending on the type of application, further protection must be ensured to prevent dust and foreign bodies from entering. Operating LED modules in the presence of certain chemical substances or in chemically enriched (aggressive) environments can impair module functionality or even cause total module failure. Detailed information can be found in our "Chemical Incompatibility" PDF on our website www.vossloh-schwabe.com/en/home/ products/led-lighting-technology/notes-on-led-technology.html The photobiological safety of the LED modules must be classified into risk groups in accordance with EN 62471: 2008. general lighting exempt group: DMC124***F / DMC125***F / DMC128***F other applications risk group 1: DMC124***F / DMC125***F / DMC128***F LUGA C 2016 HiCRI 1500 lm to 4500 lm_gb 4/5 January, 2016 4
Accessories LUGA C Holder The combination of PCB version and holder provides the option of simply replacing LED modules within their holder. Simple and secure attachment is enabled with a separate holder. LUGA C Holder For LED PCB LUGA C:: DMC104C**E, DMC115C**E, DMC118C**E Material: PBT, white Dimensions (ØxH): 35x4.2 mm Fixing holes for screws M3 Hole distance: 25 mm Push-in terminals for conductor cross-section 0.5 mm², solid or stranded wires with tinned wire ends U max. : 190 V DC for basic insulation I max. :3 A Type: 89721, Unit: 500 pcs. Ref. No.: 559165 Ø 35 mm LUGA C 2016 HiCRI 1500 lm to 4500 lm_gb 5/5 January, 2016 5