TOMBO TM BRAND GASKETS
TM TOMBO BRAND GASKETS 1
2
4 5 12 8 9 13 TOMBO TM BRAND GASKETS 1120 1995 1993 1991-NF 1938 9010-NA 1133 3
4
5
6
7
8
9
10
11
12
Sheet gaskets Product pickup 1133 CLINSIL TM Clean Conforms to the Standards and criteria for food and food additives, etc. (3-D-2, Public Notice No. 370 of the Ministry of Health & Welfare, 1959) stipulated by the Food Sanitation Act Precautions for use are on P.23. White sheet gaskets that can be used for a wide range of applications. They are clean and have excellent resistance to chemicals. They can be used at high temperature and high pressure. Alumina, which has excellent resistance to chemicals, is used as a filler, so it is not necessary to use different type of gaskets to match the type of fluid, whether it is acid or alkali. Fluororesin gaskets (CLINSIL TM Clean) Characteristics image chart The diagrams are image charts. For detailed data, refer to the following items. Acid resistance 9007-LC High temperature characteristics General fluid (water-type or oil-type fluid) 1133 High temperature characteristics Electrical insulating performance Gas sealing performance Acid resistance Alkali resistance General fluid (water-type or oil-type fluid) Joint sheet 9007-SC Acid resistance High temperature characteristics General fluid (water-type or oil type fluid) Acid resistance High temperature characteristics Electrical insulating performance General fluid (water-type or oil-type fluid) Alkali resistance Electrical insulating performance Electrical insulating performance Alkali resistance Alkali resistance Gas sealing performance Gas sealing performance Gas sealing performance Service range Recommended service range Usable range (Usable depending on the conditions of use. Consult us in advance.) Water-type fluid Oil-type fluid and corrosive fluid Gas-type fluid Fluid pressure [MPa] 4.0 3.0 2.0 1.0 175 215 Fluid pressure [MPa] 4.0 3.0 2.0 1.0 100 260 Fluid pressure [MPa] 4.0 3.0 2.0 1.0 *The thicker a gasket, the greater is the amount of deformation due to creep. For this reason, it is recommended that the thickness of the gasket be 1.5 mm in the case of a gas line in which the temperature exceeds 200. 260-200 -29 0 100 200 300 Temperature [ ] -200-29 0 100 200 300 Temperature [ ] -200-29 0 100 200 300 Temperature [ ] 13
1133 14
15
1120 1995 1993 16
1991-NF 1938 17
18
19
Comparison of fluororesin gaskets 1133 CLINSIL TM Clean 9007-SC NAFLON TM special carbon filler filled PTFE cut gasket 9007-LC NAFLON TM special filler filled PTFE cut gasket Fluororesin gaskets Product name Features Construction Service range Can be used with a wide range of fluids including acids, alkalis, petroleum, petrochemical products, organic solvents, hot oil, heating medium gas, and steam. (Excluding some strong alkalis and strong acids.) Has the highest heat resistance of all fluororesin gaskets. Can also be used where electrical insulating performance is necessary. Fluid pressure [MPa] Main constituents: PTFE, alumina 4.0 3.0 2.0 1.0 Conforms to the Standards and criteria for food and food additives, etc. (3-D-2, Public Notice No. 370 of the Ministry of Health & Welfare, 1959) stipulated by the Food Sanitation Act Water-type fluid 175 215-200 -29 0 100 200 300 Temperature [ ] Can be used with strong alkaline fluids that do not permit TOMBO No.1133 to be used. (It cannot be used with nitric acid, concentrated sulfuric acid, chromic acid, or other oxidizing fluids.) Main constituents: PTFE, carbon Fluid pressure [MPa] Water-type, oil-type or corrosive fluids 4.0 3.0 2.0 1.0 Can be used with strong acidic fluids that do not permit TOMBO No.1133 to be used. (It cannot be used with hydrofluoric acid or strong alkalis.) Can be used where electrical insulating performance is necessary. Fluid pressure [MPa] Water-type, oil-type or corrosive fluids 4.0 3.0 2.0 1.0 Fluid pressure [MPa] Oil-type or corrosive fluids 4.0 3.0 2.0 1.0 100 260-200 -29 0 100 200 300 Temperature [ ] Gas-type fluid -200-29 0 100 200 300 Temperature [ ] Gas-type fluid -200-29 0 100 200 300 Temperature [ ] Gas-type fluid Fluid pressure [MPa] 3.0 2.0 1.0 Fluid pressure [MPa] 3.0 2.0 1.0 Fluid pressure [MPa] 3.0 2.0 1.0 260-200 -29 0 100 200 300 Temperature [ ] Main constituents: PTFE, silica Recommended service range Usable range (The usable range depends upon the conditions. Be sure to consult us in advance.) -200-29 0 100 200 300 Temperature [ ] -200-29 0 100 200 300 Temperature [ ] *The greater the thickness, the larger is the deformation due to creep. For this reason, it is recommended that you select a gasket of 1.5 mm in thickness for a gas line which exceeds 200. Information Creep is deformation that occurs after the lapse of a certain time after a material has been exposed to a certain temperature and stress. Creep at normal temperature is also called cold flow. 20
9007-GL 9007-FD 9096-SGM 21
9007 9007-LP 9007-G20 22
23
9010-NA 24
25
9096 26
27
1880-GR 1215-A 1210-A 28
1200 12201221 29
30
31
1891 1834R-GR 9090-IOR 32
1834R-NA 1836R-GS-GM-GH 33
1839R 1839R-AL 18411861 34
1891 35
1891 36
37
38
39
40 41
42
43
44
45
18411861 46
47
1850C 1850V 1850P 48
1890 9200P 9200V 49
1850/1890 50
51
9200 52
53
9013-EP-DEP 90139013-D 10501051 54
9014-BBW 9014-A 2670 55
10501051 9013 56
9014 2670 57
1374 1400-TH 1400-NA-S 1400-ST 58
1364 1368 1378 59
9105 9106 9400 60
9401 90829082-BL 1600 61
TM TOMBO BRAND GASKETS 63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116