NEC Versa FX Battery Packs Congratulations on purchasing a new battery pack for your NEC Versa FX! Before installing the battery be sure to read the important information in this document. NEC provides the following battery choices.! Standard main battery OP-570-72501! Extended Life main battery OP-570-72502! Maximum Life secondary battery OP-570-72503. The Standard and Extended Life main battery packs are used as the primary power source while you use your computer away from an AC power source. The Maximum Life secondary battery can be added to the system, for use in addition to a standard or extended life battery. See the appropriate sections for information on handling, installing, removing, and charging your NEC battery. Standard Main Battery Extended Life Main Battery Maximum Life Secondary Battery following: To prevent accidental battery ignition or explosion, adhere to the! Keep the battery away from extreme heat.! Keep metal objects away from the battery connectors to prevent a short circuit.! Make sure the battery is properly installed in the battery bay.! Do not alter or disassemble the battery.! Read the precautions printed on the battery. Battery Handling Keep the following in mind when removing or replacing a battery.! Use only the battery designed for your system in your NEC computer. Mixing other manufacturers batteries, or using a combination of very old and new batteries can deteriorate battery and equipment performance.! Clean the battery connectors with a dry cloth when they get dirty.! Keep the battery out of the reach of children. NEC Versa FX Battery Packs 1
Standard or Extended Life Main Battery Pack The Standard and Extended Life main battery packs are used as the primary power source while you use your computer away from an AC power source. The following sections provide instructions on removing your old battery, and installing an NEC Standard or Extended Life main battery pack. Standard Main Battery A Battery Connectors B Alignment Grooves Extended Life Main Battery A Battery Connectors B Alignment Grooves Removing the Existing Main Battery Before you install the Standard or Extended Life main battery, remove the existing main battery. Follow the procedures in this section to remove the existing battery from your system. If your system also has a secondary battery, remove it before removing the main battery. Note If your system has a secondary life battery, you must remove it before removing the main battery. In this case, follow the procedure in the section, Removing an Existing Secondary Life Battery before performing the steps below. 1. Save your files and put the system in a Standby mode. Click Start, select Shutdown, select Standby and click OK. The LCD goes blank and the status LED blinks green when the system is in Standby mode. Note The main battery can be removed while the system is in Standby mode. 2. Close the LCD panel and turn over the system. 2 NEC Versa FX Battery Packs
3. Slide the battery release latch toward the right side of the system and hold firmly. Locating the battery bay release latch A Main Battery B Battery Release Latch 4. Continue to hold the battery release latch as you slide the battery out of the system. Removing the main battery A Battery Bay Connectors B Battery Bay Release Latch C Main Battery 5. If you discard the old battery, see the section, Battery Disposal. NEC Versa FX Battery Packs 3
Installing the Standard or Extended Life Main Battery Pack Install your main battery as follows: Note Using a combination of very old and new batteries can deteriorate battery and equipment performance. 1. Locate the alignment groove on the edge of the main battery. 2. Locate the alignment groove inside the battery bay. 3. Align the grooves on the battery with the grooves in the bay. 4. Slide the battery into the bay until securely locked into place. See the figure that corresponds to your new battery. Inserting the Standard main battery pack A Battery Bay Connectors B Battery Bay Release Latch C Alignment Grooves D Standard Main Battery Inserting the Extended Life main battery pack A Battery Bay Connectors B Battery Bay Release Latch C Alignment Grooves D Extended Life Main Battery 5. Turn over the system. 6. Take the system out of Standby mode by sliding the power button to the right. 7. Fully charge the new battery the first time you charge it (see the section, Charging the Battery ). Also see the section, Battery Precautions for important safety information. 4 NEC Versa FX Battery Packs
Maximum Life Secondary Battery The Maximum Life secondary battery can be added to the system for use in addition to the main battery. The secondary battery gives your system its maximum battery life while you use your computer away from an AC power source. The following sections provide instructions on removing an existing secondary battery (if any) and installing the Maximum Life secondary battery pack. Maximum Life secondary battery A Maximum Life Secondary Battery B Connector C Coin-Type Screws D Clips Removing an Existing Secondary Battery If your system has an existing secondary battery, you need to remove it. Remove the secondary battery as follows. 1. Save your files, exit Windows and turn off system power. Always power off the system before removing the secondary battery. If the system is not powered off before the secondary battery is removed, data can be lost. 2. Close the LCD panel and turn over the system. 3. Use a coin or a screwdriver to turn the battery screws 90 as marked to unlatch the secondary battery. NEC Versa FX Battery Packs 5
Locating the secondary battery A Secondary Battery B Coin-type Screws C Main Battery 4. Lift the secondary battery from the edge it shares with the main battery (see the following figure). Clips secure the other edge of the battery to the computer. Once the battery is angled up enough the clips disengage from their slots. Lifting the edge of the secondary battery A Clips (Hidden) B Existing Secondary Battery C Top of the Computer D Main Battery 5. Lift the battery off the system. 6. If you are not adding another secondary battery at this time, slide the connector door closed. 7. If you discard the old battery, see the section, Battery Disposal. 6 NEC Versa FX Battery Packs
Installing the Maximum Life Secondary Battery Pack Install the Maximum Life secondary battery as follows: Note Using a combination of very old and new batteries can deteriorate battery and equipment performance. 1. Save your files, exit Windows and turn off system power. Always power off the system before adding the secondary battery. 2. Slide open the connector door on the underside of the computer. 3. Hook the battery clips into the matching slots in the computer. Keep the other edge of the battery raised. 4. Make sure the screws are turned so they can be inserted in their slots on the computer. 5. Lower the battery onto the computer and then press it firmly to seat the battery connector in the computer. Aligning the Maximum Life Secondary Battery A Coin-type Screws B Connector C Clips D Connector Door E Connector F Slots for Coin-type Screws G Main Battery NEC Versa FX Battery Packs 7
6. Use a coin or a screwdriver to turn the battery screws 90 as marked to secure the battery to the computer (see the following figure). Securing the coin-type screws A Turn Screws as Marked on Battery 7. Turn over the system. 8. Fully charge the new battery the first time you charge it (see the section, Charging the Battery ). Also see the section, Battery Precautions for important safety information. Charging the Battery Charge the main battery and secondary battery by simply connecting your NEC system to an AC power source. To monitor the charging activity, observe the battery charging LED on the front of the system. The battery charging LED lights as follows:! Lights amber when the primary battery is charging.! Blinks amber if the primary battery encounters an error while charging.! Lights green when the secondary battery is charging.! Blinks green if the secondary battery encounters an error while charging. During charging, keep the environmental temperature between 32 F and 104 F (0 C to 40 C). For directions on getting a detailed battery status, see the section, Determining Battery Status. Determining Battery Status Your NEC Versa system provides tools to help you keep track of the main and secondary battery power level. If your system is configured (default setting) to display the power icon on the taskbar, an electrical plug is displayed when the system is connected to an AC power source or a battery icon displays when the system is not connected to an AC power source. Use the system s power meter to determine battery status. Access the system s power meter in the following ways:! Move the cursor over the power icon on the taskbar to display the remaining battery power for the system s main battery. 8 NEC Versa FX Battery Packs
! Right click the power icon on the taskbar to open the power meter or to adjust power properties.! Double click the power icon on the taskbar to display the remaining power for both the main and secondary battery (if any).! Go to Start, Settings, Control Panel, and double click the Power Management icon and select the Power Meter tab. Battery Precautions To prevent accidental battery ignition, rupture, or explosion, adhere to the following precautions. There is a danger of explosion if the battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturer s instructions. To avoid personal injury and property damage, read these battery precautions on handling, charging, and disposing Li-Ion batteries.! Keep the battery away from heat sources including direct sunlight, open fires, microwave ovens, and high-voltage containers. Temperatures over 140º F (60ºC) may cause damage.! Do not drop or impact the battery.! Do not disassemble the battery.! Do not solder the battery.! Do not puncture the battery.! Do not use a battery that appears damaged or deformed, has any rust on its casing, is discolored, overheats, or emits a foul odor.! Keep the battery dry and away from water.! Keep metal objects away from battery connectors. Metal objects in contact with the connectors can cause a short circuit and damage. If the battery leaks:! If the battery leaks onto skin or clothing, wash the area immediately with clean water. Battery fluid can cause a skin rash and damage fabric.! If battery fluid gets into eyes, DO NOT rub; rinse with clear water immediately and consult a doctor.! Take extra precautions to keep a leaking battery away from fire. There is a danger of ignition or explosion. Battery Disposal The main battery and secondary battery are made of Lithium Ion (Li-Ion). Contact your local waste management officials for information regarding the environmentally sound collection, recycling, and disposal of the batteries. NEC Versa FX Battery Packs 9
10 NEC Versa FX Battery Packs NEC Versa FX Battery Packs 819-200627-001 12/99!"#$%&''(&)%''#!