Watz Hydraulik Your specialist for customised and standard hydraulic products

Watz Hydraulik Your specialist for customised and standard hydraulic products

About Watz Hydraulik Contents 2 About Watz Hydraulik 3 Watz engineering 4 Hydraulic cylinders 7 Hydraulic systems 8 Control blocks 9 Hydraulic systems and units 10 Special solutions 11 Hydraulics service and technical retail Watz Hydraulik specialises in the field of hydraulic drive and control technology. We have been developing and manufacturing hydraulic products at our Lollar site in central Hesse for over 40 years now. Graduate engineer Horst Watz was quick to recognise the technological potential and superiority of hydraulic drive systems over their mechanical counterparts. In 1971, he founded a distribution company for hydraulics and pneumatics and, a short time later, began to develop and manufacture his own hydraulic units. Today, Watz manufactures hydraulic systems for customers all over the world, both as customised, special solutions and standard systems and cylinders. The range of services offered by Watz Hydraulik encompasses everything from consulting, development, production, assembly and commissioning to maintenance, repair and the conversion of hydraulic components and systems. Thanks to this end-to-end service offering, Watz ensures a permanently high level of system availability. Together with subsidiary FAUDI GmbH, this family enterprise grew into the Watz corporate group. FAUDI is a global company specialising in filtration technology. Many years of experience make the companies strong business partners. Both companies are jointly certified to DIN EN ISO 9001:2008. With a more than 150-strong workforce, the Watz Group is your partner for customised and standard hydraulic products. 2

Consulting and development Watz engineering Project planning Engineering is at the heart of our activities. Each and every day, our engineers tirelessly devote themselves to the process of implementing the specialist requirements of our customers in the development of sophisticated and intelligently controlled hydraulic systems. Consulting phase We support our customers in an advisory role in the early project phase and develop not only the optimum hydraulic solution but also the best route to implementation. Development phase We support our customers at all times during the subsequent development and implementation phase too. This ensures the fastest possible implementation and leads to tangible cost and time savings. Outcome Hydraulic systems often have to operate over many years under extreme conditions. To ensure their safe and reliable operation, detailed precision and the optimum interaction of all components is essential. Our quality standards are extremely high: from CAD-based system development, production of the manufactured parts and module assembly through to final system installation and commissioning on site. 3

Hydraulic cylinders Watz Hydraulik has been manufacturing powerful, dynamic and robust hydraulic cylinders for more than 40 years now. During our many years of work, we have developed our own cylinder program covering all the most common application areas. We also produce customised versions at the special request of our customers. Standard hydraulic cylinders Range ZD 160 bar ZM 250 bar ZE 300 bar ZB 500 bar Applicable standards Design Round cylinder Round cylinder Round cylinder Block cylinder Characteristics Robust screw-fitted design Compact design Excellent value for money Wide range of applications 7 attachment types 3 sealing variants Robust screw-fitted design Compact design Excellent value for money Wide range of applications 12 attachment types 3 sealing variants Single-acting hydrocylinder Robust screw-fitted design Compact design Excellent value for money Wide range of applications 8 attachment types Compact block design Double- or single-acting block cylinder with or without spring return 3 attachment types optionally upgradable with: Synchronisation function Position measuring system optionally upgradable with: Synchronisation function Position measuring system optionally upgradable with: Position measuring system Position monitor Rated pressure 160 bar 250 bar 300 bar 500 bar Piston Ø from 20 to 125 mm from 32 to 180 mm from 16 to 200 mm Piston rod Ø from 14 to 90 mm from 18 to 125 mm Plunger from 30 to 100 mm from 10 to 125 mm Max. stroke length up to 250 mm Max. compressive force 196.4 kn 636.3 kn 235.6 kn 1570 kn Max. pulling capacity 134.7 kn 398.5 kn 957 kn Hydraulic fluid Mineral oils DIN 51524 HL, HLP Mineral oils DIN 51524 HL, HLP Mineral oils DIN 51524 HL, HLP Mineral oils DIN 51524 HL, HLP Hydraulic fluid temperature range -20 to +80 C -20 to +80 C -20 to +80 C Installation position Stroke speed (depending on power connection) (depending on power connection) (depending on power connection) (depending on power connection) 4

Product range All of our hydraulic cylinders, systems and units are tested by our Quality Assurance team to a level far above and beyond the required working pressures, for example to DIN, AD regulations, ASME, ANSI, ATEX and DIN ISO 9001. Standard industrial hydraulic cylinders ZL-RX 250 bar ZN-RX 250 bar ZH-RX 350 bar ZI 160 bar ISO 6022 ISO 6020/2 Round cylinder Round cylinder Round cylinder Tie rod cylinder Flexible, robust flange design All wear parts can be easily removed and replaced Easy-to-replace cylinder thanks to international factory standard sizes 6 attachment types 3 sealing variants Flexible, robust flange design All wear parts can be easily removed and replaced Easy-to-replace cylinder thanks to international factory standard sizes 6 attachment types 3 sealing variants Flexible, robust flange design All wear parts can be easily removed and replaced Easy-to-replace cylinder thanks to international factory standard sizes 5 attachment types 3 sealing variants Tie rod design Easy-to-replace cylinder thanks to DIN-standardised sizes 13 attachment types 2 sealing variants optionally upgradable with: Synchronisation function Position measuring system optionally upgradable with: Synchronisation function Position measuring system optionally upgradable with: Synchronisation function Position measuring system 250 bar 250 bar 350 bar 160 bar from 40 to 320 mm from 50 to 200 mm from 40 to 200 mm from 25 to 200 mm from 22 to 220 mm from 32 to 140 mm from 28 to 140 mm from 12 to 140 mm 2010.6 kn 785.2 kn 1,099.6 kn 785.6 kn 1225.2 kn 440.3 kn 560.7 kn 400.4 kn Mineral oil to DIN 51524 HL, HLP, Water glycol HFC Mineral oil to DIN 51524 HL, HLP, Water glycol HFC Mineral oil to DIN 51524 HL, HLP, Water glycol HFC Mineral oil to DIN 51524 HL, HLP -20 to +120 C -20 to +120 C -20 to +120 C -20 to +80 C (depending on power connection) (depending on power connection) (depending on power connection) (depending on power connection) 5

Pressure intensifiers / special cylinders Pressure intensifiers Special cylinders Range DR 700 bar Applicable standards Design Characteristics Pressure intensifiers Transmission ratio 1:5, 1:10, 1:20 Volumes from 0.05 to 1.0 litres Blocking valve (pneumatic/hydraulic only) as per customer requirements Industry and project cylinders upon request optionally upgradable with integrated: Forming cylinder Workpiece hold-down device Position measuring system Pressure transmitter Pneumatic/hydraulic Transmission ratio: 1:10 and 1:20 Max. primary pressure: 10 bar Max. secondary pressure: 100 to 200 bar Hydraulic fluid: Lubricated air Hydraulic/hydraulic Transmission ratio: 1:5 Primary pressure: 140 bar Secondary pressure: 700 bar Hydraulic fluid: Mineral oils DIN 51524 HL, HLP Hydraulic fluid temperature: -20 to +80 C 6

Product range Hydraulic systems Watz Hydraulik produces hydraulic systems in all sizes: from compact mini-drive systems with a 2.5-litres tank to modular drive systems with 800-litres tanks. We also supply special systems with a tank volume of up to 30,000 litres in a variety of versions and of course in accordance with international standards and regulations. Compact drive systems: KA mini systems Characteristics: Stable C-steel oil vessel from NG 2.5 to 7 litres Fully hydraulic controller can be integrated in the control block External attachment of valve interconnection Wide range of applications Low noise Modular drive systems: AGA small systems Characteristics: Stable aluminium oil vessel from NG 07 to 70 litres Use of constant and variable-capacity pumps Compact design Clear and maintenance-friendly design AGS modular drive systems Characteristics: With C-steel oil vessel from NG 63 to 800 litres Basic system with pump motor group, oil vessel accessories, return flow filter, float switch and thermostat Modular construction of control, accumulator and cooling system Systems can be expanded with minimal outlay Special systems built to customer requirements Characteristics: C-steel or stainless steel vessels built to customer requirements as per international standards such as: ASME and ASTM up to 30,000 litres Strength analyses, material certifications and test certificates as per customer requirements With partition and noise-reduction wall Pump motor group Individual design of pumps, controller, accumulator, filter etc. 7

Control blocks When it comes to sophisticated control solutions for hydraulic systems, our specialists are in their element. Most of our control units are developed block by block. This compact and robust design with minimal piping is maintenance-friendly and space-saving. By using high-quality valves, we offer extremely compact solutions that are tailored precisely to our customers requirements and designed for pressure ranges of up to 500 bar. The end result is a hydraulic control concept that covers all of your individual requirements. 8

Product range Hydraulic systems and units Watz Hydraulik develops, plans and implements complete hydraulic solutions for a variety of industrial applications. Solutions include hydraulic drives and hydraulic power sources. Of course, we also provide the electrical planning services and electrical controls. Our in-house Electronics department offers a range of services including the planning, implementation and assembly of complete electronic control units as well as software development. Certified, customized and aligned towards our customers processes. 9

Special solutions Our know-how is in demand when it comes to innovative special solutions too. Hydraulic briquette presses for material recovery are a great example of this. Hydraulic solutions from Watz combined with filter systems from FAUDI turn expensive production residues into recyclable secondary raw materials. One example of a cost-effective, environmentally friendly special solution from Watz Hydraulik. 10

Hydraulics service and technical retail Hydraulics service and technical retail Commissioning The expert commissioning of our own systems as well as those from other manufacturers on site is all part of our service. We know that professional commissioning cuts costs over the long term and increases the product life time. This ensures that we achieve our aim of total operational readiness of a system. Repairs and maintenance Watz Hydraulik continues to offer support even after your product has entered operation. Our professional maintenance services ensure not only optimum capacity utilisation of the systems but also a long service life. Thanks to our highly experienced service team, we can perform maintenance and repairs quickly, professionally and reliably directly on site. System optimisation and retrofitting We support our customers in any necessary optimisation and retrofitting work. Technological modernisation and alteration measures allow systems to be upgraded to the latest state of the art quickly and without major reinvestment. Improved system performance boosts productivity and helps to save energy and resources. Hydraulic components for every application With our own technical retail outlet, we offer an outstanding range of hydraulic components from a variety of highly renowned manufacturers. Many items are available immediately and can be picked up directly or sent by express delivery. Training programmes We run our own training programmes to help customers continuously expand their expertise. We not only train customers in commissioning but also provide training for technical purchasers and engineers. 11

Watz Hydraulik GmbH Auweg 8 35457 Lollar Germany Phone +49 (0) 6406 91 02-0 Fax +49 (0) 6406 91 02-41 info@watzhydraulik.de www.watzhydraulik.de At our company headquarters in Lollar, we are available weekdays from 7:30 am to 5 pm. Parker Store (retail outlet): Phone +49 (0) 6406 91 02-14 Technical retail outlet: Phone +49 (0) 6406 91 02-23