Ultra Tugger Cable Puller and Pulling Package

SERVICE MANUAL 00-22 Ultra Tugger Cable Puller and Pulling Package Serial Code ADB Read and understand all of the instructions and safety information in this manual before operating or servicing this tool. Register this product at www.greenlee.com 9997 REV 205 Greenlee Textron Inc. /5

Table of Contents Safety... 2 Purpose of this Manual... 2 Important Safety Information... -5 Grounding Instructions... Operation... 7 Maintenance... -9 Exploded Views and Parts Lists Ultra Tugger (with wiring diagram)... 0- Gearmotor (5007929)... 2- Motor (50079220)... Force Gauge... 5 Accessories... -22 Safety Safety is essential in the use and maintenance of Greenlee tools and equipment. This service manual and any markings on the tools provide information for avoiding hazards and unsafe practices related to use of this tool. Observe all of the safety information provided. Do not operate this tool unless fully trained to do so, or under trained supervision. Purpose of this Manual This manual is intended to familiarize authorized Greenlee service center personnel with the safe operation and maintenance procedures for the Greenlee 00-22 Ultra Tugger cable puller. Keep this manual available to all personnel. Replacement manuals are available upon request at no charge at www.greenlee.com. Other Publications Instruction Manual: 999502 (IM 529) All specifications are nominal and may change as design improvements occur. Greenlee Textron shall not be liable for damages resulting from misapplication or misuse of its products. Ultra Tugger is a registered trademark of Textron Innovations Inc. Loctite and 22 are registered trademarks of Loctite Corporation. Texaco is a registered trademark of Texaco Inc. KEEP THIS MANUAL Greenlee / A Textron Company 2 55 Boeing Dr. Rockford, IL 09-29 USA 5-97-7070

IMPORTANT SAFETY INFORMATION SAFETY ALERT SYMBOL This symbol is used to call your attention to hazards or unsafe practices which could result in an injury or property damage. The signal word, defined below, indicates the severity of the hazard. The message after the signal word provides information for preventing or avoiding the hazard. Immediate hazards which, if not avoided, WILL result in severe injury or death. Hazards which, if not avoided, COULD result in severe injury or death. Hazards or unsafe practices which, if not avoided, MAY result in injury or property damage. Read and understand all of the instructions and safety information in this manual before operating or servicing this tool. Failure to observe this warning will result in severe injury or death. Electric shock hazard: Disconnect the cable puller from the power supply before servicing. Failure to observe this warning could result in severe injury or death. Flying components hazard: Inspect and verify the maximum load-bearing capacity or maximum strength of all structural supports, pulling system components and anchoring systems before setting up the puller. Any component that cannot withstand the maximum cable-pulling forces could break and strike nearby personnel with sufficient force to cause severe injury or death. Do not allow anything other than the pulling rope to contact the capstan. A grip, swivel, or other component could break and strike operator with great force. Failure to observe these warnings could result in severe injury or death. Crushing hazard: Do not stand directly under a vertical pull. Cable could fall suddenly from the conduit. Failure to observe this warning could result in severe injury or death. Explosion hazard: Do not operate the cable puller in a hazardous environment. Hazards include flammable liquids and gases. Failure to observe this warning will result in severe injury or death. Greenlee / A Textron Company 55 Boeing Dr. Rockford, IL 09-29 USA 5-97-7070

IMPORTANT SAFETY INFORMATION Flying components hazard: Locate the puller so that it is close to the conduit. Rope, cable, or connectors could break under tension, causing the rope to whip violently. Failure to observe this warning could result in severe injury or death. Attach the pulling rope to the cable with appropriate types of connectors as described in this manual. Select connectors with a maximum-rated capacity of 5. kn (000 lb). An under-rated connector could break under tension. Failure to observe this warning could result in severe injury or death. Shear Point: Do not put fingers through holes in elbow unit. Rotating parts could cut off fingers. Failure to observe this warning could result in severe injury or death. Do not maintain a stationary rope on a rotating capstan. The wear generated could cause the rope to break under tension and whip violently. Check the condition of the entire rope before use. An under-rated, worn or damaged rope could break and whip violently. Use a double-braided composite rope with the following characteristics: Maximum Rated Capacity: at least 5. kn (000 lb) Average Breaking Strength: at least kn (2,000 lb) Failure to observe these warnings could result in severe injury or death. Crushing hazard: Keep hands away from the capstan. Rope at the capstan could crush a hand. Failure to observe this warning could result in severe injury or death. Entanglement hazard: Do not wrap rope around hands, arms, waist or other body parts. Do not stand in spent coils or tailed rope. Hold rope so that it may be released quickly. Failure to observe this warning could result in severe injury or death. Greenlee / A Textron Company 55 Boeing Dr. Rockford, IL 09-29 USA 5-97-7070

IMPORTANT SAFETY INFORMATION Rope, cable, or a connecting device could break under tension, causing the rope to whip violently. Do not allow any unnecessary personnel to remain in the area during the pull. Do not allow any personnel to stand in line with the pulling rope. Failure to observe these warnings could result in severe injury or death. Entanglement hazard: Do not operate the cable puller while wearing loose-fitting clothing. Retain long hair. Failure to observe this warning could result in severe injury or death. Rope overlap hazard: Do not allow the rope to become overlapped on the capstan. If an overlap begins to develop, relax the tailing force immediately and shut off the cable puller. Failure to observe this warning could result in severe injury or death. Lifting hazard: Use this tool for manufacturer s intended purpose only. Do not use the cable puller as a hoist or winch. The cable puller cannot lower a load. The load could fall. Failure to observe this warning could result in severe injury or death. Tipping hazard: Wear eye protection when using this tool. Failure to wear eye protection could result in severe eye injury from flying debris. When using the wheeled carriage to transport the Ultra Tugger: Keep personnel out of the path of transport. Evaluate the terrain over which the carriage is to move. If in doubt, obtain additional help and move the carriage slowly. Do not transport over inclines of more than 0. Do not transport the carriage with boom tubes longer than the supplied ' and ' tubes. Inspect puller and accessories before use. Replace any worn or damaged components with Greenlee replacement parts. A damaged or improperly assembled item could break and strike nearby personnel with sufficient force to cause severe injury or death. 0 Failure to observe this warning could result in severe injury or death. Greenlee / A Textron Company 5 55 Boeing Dr. Rockford, IL 09-29 USA 5-97-7070

Grounding Instructions -Amp / 20-Volt Plug and Grounded Receptacle Electric shock hazard: Connect this tool to a grounded receptacle on a -amp GFCIprotected circuit. Failure to observe this warning could result in severe injury or death. Plug Receptacle This tool must be grounded. In the event of a malfunction or breakdown, an electrical ground provides a path of least resistance for the electric current. This path of least resistance is intended to reduce the risk of electric shock to the operator. This tool s electric cord has a grounding conductor and a grounding plug as shown. Connect the plug to receptacle that is properly installed and grounded in accordance with all national and local codes and ordinances. Do not use an adapter. This tool is equipped with a European-style electrical plug. The electrical plug can be replaced with a compatible plug for the country in which the tool will be used. The electrical plug should be replaced by a qualified electrician. Do not use an adapter. Greenlee / A Textron Company 55 Boeing Dr. Rockford, IL 09-29 USA 5-97-7070

Operation. Fish the rope through the conduit. 2. Set up the cable puller. See Typical Setups illustrations and instructions in Instruction Manual 999502 (IM 529). c. Push the ramp toward the mounting plate and rotate it counterclockwise until it locks into place. Set up the cable puller so that the rope will approach the capstan at an angle of 90 (±5 ). Angles outside of this range may cause the rope to overlap. 90 (±5 ). Check the I/O switch on the puller to be sure it is OFF (O). Plug the puller into the receptacle of the standard force gauge. 5. Connect the force gauge to an appropriate power supply (see Grounding Instructions in this manual). Note: If using an extension cord, it must be rated for 20 amps. Use the shortest cord possible. Longer cords reduce puller speed.. Position the force gauge so that it can be monitored by the puller operator. Duty Cycle Table. Set the rope ramp as follows: a. Wind the rope several times around the capstan. Color Band on Meter Pounds of Pulling Force Duty Cycle (in minutes) Green 0 7. kn (0 000 lb) continuous Yellow 7. 5. kn (000 000 lb) 5 per hour Red over 5. kn (000 lb) puller will stop b. Pull the ramp away from the mounting plate and rotate it until the flat surface contacts the rope. 7. Turn the circuit breaker in the force gauge ON (I).. Grasp the tailing end of the rope. Apply a slight amount of tailing force. 9. Turn the puller ON (I). 0. Tail the rope, allowing the spent rope to accumulate on the floor between the operator and the puller.. When the pull is complete, turn the puller OFF (O). Tie off the rope and anchor the cable. Entanglement hazard: Do not wrap rope around hands, arms, waist or other body parts. Do not stand in spent coils or tailed rope. Hold rope so that it may be released quickly. Failure to observe this warning could result in severe injury or death. Greenlee / A Textron Company 7 55 Boeing Dr. Rockford, IL 09-29 USA 5-97-7070

Maintenance Disconnect power supply before servicing this tool, or when not in use. Failure to observe this warning could result in severe injury or death. 2. Secure motor wires to the motor using tiewraps. Make sure the wires will not contact the commutator.. Connect the brown motor wire to the positive (+) terminal on the rectifier (0). Connect the blue motor wire to the negative ( ) terminal on the rectifier. Maintenance should be performed by authorized personnel only. General Maintenance Notes Replace any part that is broken, cracked or worn. Replace any bearings that don t turn freely. Clean all mating surfaces before assembly. Replace gearbox grease with Texaco Regal AFB or equivalent. Specific Service Notes Average brush life for commutator brushes is about 00 hours. Replace brushes if they are shorter than 9.5 mm (/"). Replace rope ramp if it is grooved more than.5 mm (/"). Replace the capstan if it is grooved more than 0.5 mm (/"). The puller should not require any lubrication during its normal service life. Switchbox Removal. Remove the four Phillips head screws and cover from the switchbox (). 2. Remove the green hex head screw (2), three lock washers (29) and three yellow and green wires from the heat sink plate (2).. Remove the brown and blue motor wires from the filter (0).. Remove fifteen hex head screws (2), and top cover (2) from the motor. Be careful not to damage the brown, blue, and green motor wire when you remove the top cover from the motor. 5. Remove the four hex nuts (5), four screws (), and switchbox () from the top cover. Switchbox Assembly Notes. If replacing the rectifier (0), or filter (), use a thermal contact grease before mounting to heat sink (2). The first reduction hub will be damaged if the motor wires are reversed.. Connect the green and yellow wires from the power cord, motor, and filter to the heat sink plate. Motor Removal See Exploded View Ultra Tugger. Remove switchbox. 2. Remove seven hex head screws (2) and cover (20) from the motor.. Use the 7/" wrench to remove two hex nuts () and end cap (9). See Exploded View Motor. Push in and pull out the tab to release the commutator brush springs (2). 5. Use 7/" wrench and remove four hex nuts, two lock washers, and tail housing () from the motor.. Remove brush assembly plate (). 7. Remove the O-ring (5), baffle (22), and end support () from the motor housing. (See Exploded View Ultra Tugger. ). Remove magnet housing (5). 9. Remove armature (). 0. Remove screw holding the air vent protective screen and remove screen (9). Motor Assembly Notes. Apply gasket sealant between gearbox housing and the outside of the front armature housing. 2. If the armature does not turn freely after installation, the wrong gear teeth were engaged.. Hold armature in place when installing the magnet housing. Position magnet housing with the roll pin outward and pointed towards o clock. The square hole of the mounting plate should be positioned at 0 o clock.. Install commutator brush assembly. Wires should be at the 9 o clock position. 5. Insert magnet housing roll pin into the recess on the tail housing. Greenlee / A Textron Company 55 Boeing Dr. Rockford, IL 09-29 USA 5-97-7070

Maintenance (cont d) Capstan Removal. Use a -/" inch -point socket to remove capstan retaining bolt () and washers (5). 2. Pull the capstan (7) off of the shaft. If the capstan is stuck: Pull out the rope ramp. Use two pry bars on opposite sides of the capstan between the gear housing and the capstan. Do not pry against the grease seal. Doing so will damage the seal.. Remove key (9).. Remove rope ramp (). Capstan Assembly Notes. Remove oxidation before assembling. 2. Do not hammer capstan onto shaft. Use a 5 mm (2-/2") or longer bolt to draw the capstan onto the shaft. Right Angle Sheave Bracket Removal. Remove detent pin (). 2. Slide arm towards motor. Use a small punch to remove the roll pin (2).. Remove bracket (9). Gearbox Disassembly. Remove motor, capstan and right angle sheave bracket. 2. Remove the screws () on the motor side of the gearbox. Remove the mounting plate (20).. Remove the motor mounting housing (2).. Pull out the st reduction planet gear assembly and thrust washer. 5. Pull out the center shaft (2).. Pull out the 2nd reduction planet gear assembly and thrust washer. 7. Push out the output shaft/rd reduction gear assembly and thrust washer.. Remove the screws (7) holding the ring gear (). 9. Tap the bearing housing () off the ring gear and dowel pins. Do not mar the mating surface to the ring gear. Gearbox Assembly Note. Clean all ring mating surfaces. Apply a flange sealant (Loctite 55 or equivalent) to all ring mating surfaces. 2. Install center shaft with the small diameter towards the motor.. Install the mounting plates. When viewed from the motor end, the motor mounting studs should be positioned at and 7 o clock. The square hole in the mounting plate should be between 0 and o clock.. Position mounting plates so the screw heads on the capstan side fit into the counterbores of the mounting plates. Disassembly of Planet Gear Carriers. Remove the flat head screws. 2. Tap or pry off the hub plate from the hub and dowel pins.. Remove the thrust washers, gears, thrust washers and shaft.. Remove sun gear ONLY if replacement is required. Planet Gear Carrier Assembly. Place the shafts in the hub. The end with the flat should face outward. 2. The st planet reduction gears must be positioned with the gear end towards the capstan.. When replacing the st reduction gear bearing/ clutch, the locked arrow direction must be counterclockwise (when viewed from the gear end).. When replacing the ball bearing on the output shaft, the thick side of the outer race must face the capstan. 5. Use a removable thread locking compound, such as Loctite 22 Threadlocker or equivalent, on the #0 2 flat head screws (items 5 and on the gearmotor). Follow the manufacturer s instructions for curing. Greenlee / A Textron Company 9 55 Boeing Dr. Rockford, IL 09-29 USA 5-97-7070

Exploded View and Wiring Diagram 5007927 Ultra Tugger (Serial Code ADB) YELLOW & GREEN BLUE BROWN 0 2, 29 5 9 BLUE BROWN 2 9 2 5 0 5 BLUE BLUE YELLOW & GREEN PE NOTE: Connect the BROWN motor wire to positive (+) terminal on rectifier. BROWN BROWN NOTE: Use thermal contact grease on 0 & before mounting to 2 heat sink. 2 I O 2 2 2 2 0 2 29 7 52 27 25 MOTOR YELLOW & GREEN Wiring Diagram 2 20 5 9 2 7 5 29 22 50 5 7 5 9 2 2 0 9 7 Greenlee / A Textron Company 0 55 Boeing Dr. Rockford, IL 09-29 USA 5-97-7070

Parts List 5007927 Ultra Tugger (Serial Code ADB) Key Part No. Description QtyKey Part No. Description Qty 5007090 Switchbox... 2 5007050 Switch guard... 50072 Cord unit, power... 9050277 Screw, cap, # 2 x.500" socket head... 5 9059 Nut, hex, # 2... 9059559 Screw, machine, # 2 x.75" button head...2 7 90529 Screw, machine, #0 2 x.750" round head... 9055 Nut, hex, #0 2 lock, zinc-plated... 9 9975 Switch / circuit breaker... 0 90 Rectifier, 50 amp, bridge... 9 Filter, Curtis... 2 9052 Bushing, strain relief... 929 Nut, conduit, /2" lock... 50070 Wire unit, brown...2 5 907 Terminal, /" push-on ga. insulated...2 905002 Rivet, pop,.25... 7 5007092 Plate, ID... 50070959 End support... 9 5007097 End cap... 20 5007099 Cover... 2 5007025 Cover, top... 22 500709 Baffle... 2 905559 Screw, #0- x /2...22 2 50070975 Heat sink... 25 905520 Bushing, Heyco... 2 500790 Wire unit, blue...2 27 905527 Screw, SHC M x 0.5 x mm... 2 905297 Screw, # x.75 SLFTPG hex green... 29 9059 Washer, internal lock... 0 5007 Wire unit, green... 50077 Wire unit, green... 2 90529 Nut, hex #-2...2 9052 Washer, flat #-2...2 9057059 Nut, hex /-2... 5 9055252 O-ring,.25 x.75 x.25... 5007929 Gearmotor... 7 500070 Capstan... 500075 Ramp, rope... 9 50007 Bar, tie... 0 5050 Sheave, right angle... * 500072 Puller pin...2 2* 90507002 Pin, roll,.7" x.50"... * 905002 Clip, hitch pin, #...2 9055 Screw, cap, / x.500" hex head, grade 5... 5 905507 Washer, flat,.70 x 2.000 x.250"...2 90592 Screw, shoulder, 5/ x -/ x /2... 7 905279 Nut, hex, /2 zinc-plated... 90552 Hitch pin, Rein Leitzke #0 07... 9 90555 Key, square,.75" x."... 50 90505 Screw, machine, # 2 x.2" hex head, green... 5 5007 Wire unit... 52 520599 Plate, switch grounding... Repair Kit * 5007 Kit, puller pin (includes one each of the items marked with an asterisk)...2 Decals 2 500029 Decal, Warning... 5000590 Decal, Read IM... 5007092 Decal, ON/OFF... Greenlee / A Textron Company 55 Boeing Dr. Rockford, IL 09-29 USA 5-97-7070

Exploded View Gearmotor (5007929) 7 20 2 25 2 27 0 2 0 5 7 9 2 2 2 2 29 7 29 9 2 20 2 5 0 29 22 5 29 5 2 2 2 9 Greenlee / A Textron Company 2 55 Boeing Dr. Rockford, IL 09-29 USA 5-97-7070

Parts List Gearmotor (5007929) Key Part No. Description QtyKey Part No. Description Qty 500057 Bearing housing... 2 50000 Motor mount... 500057 Output hub... 50005 Output hub plate... 5 500022 2nd Reduction hub... 5000592 2nd Reduction hub plate... 7 50000 st Reduction hub... 500057 st Reduction hub plate... 9 50007 st Reduction shaft...2 0 500095 2nd Reduction shaft... 5000509 rd Reduction shaft... 2 500079 Center shaft... 5000525 st Reduction planet gear...2 50005 2nd Reduction sun gear... 5 50005 2nd Reduction planet gear... 5000550 rd Reduction sun gear... 7 50005 rd Reduction planet gear... 5000 Ring gear... 9 50079220 Motor, 20 V... 20 50005 Motor mounting plate...2 2 90520 Clutch, Torrington #RCB-02...2 22 9052 Bearing, Torrington #B-20... 2 90525 Bearing, Torrington #B-2... 2 9052 Bearing, Torrington #B-...5 25 905272 Bearing, Torrington #BH-... 2 90520 Inner race, Torrington #IR-22... 27 905299 Bearing, Fafnir #7209W... 2 90502 Seal, Freudenberg-Nok #UF-02E... 29 90529 Thrust washer,.70 x.25 x.020"... 0 9050 Thrust washer,.50 x.00 x.020"... 9057 Thrust washer,.20 x.50 x.00"... 2 90579 Dowel pin,.250 x.250"... 9050 Dowel pin,.2 x.25"...9 5 9055 Screw, cap, #0 2 x.500", skt. flt. hd...5 9055 Screw, cap, #0 2 x.750", skt. flt. hd... 7 905 Screw, cap, / 2 x 2.00", skt. hd... 905055 Screw, cap, / 2 x.500", skt. hd... 9 905200 Nut, hex, / 20...2 Repair Kits 50022920 Gearmotor repair group # (includes,,, 7, 2, 2[2], 29[2],, ) 5002295 Gearmotor repair group #2 (includes 5,, 0, 5,, 22, 2, 29[2],, 5) 50022970 Gearmotor repair group # (includes 7-9,,, 2, 2, 0[2],,, 5) Greenlee / A Textron Company 55 Boeing Dr. Rockford, IL 09-29 USA 5-97-7070

Exploded View and Parts List Motor (50079220) 9 7 0 0 5 2 Key Part No. Description QtyKey Part No. Description Qty 9705 Commutator brushes...2 2 970 Commutator brush retention spring... 955 Tail housing... 950 Brush assembly plate... 5 95 Magnet housing... 90 Armature... 7 905 Belleville washers...2 9077 Bearing... 9 992 Screen... 0 97000 Threaded rod...2 Greenlee / A Textron Company 55 Boeing Dr. Rockford, IL 09-29 USA 5-97-7070

Exploded View and Parts List 500720 Force Gauge (Serial Code ADD) FORCE INDICATOR 7 BROWN BROWN RECEPTACLE BLUE 7 5 9 SWITCH BROWN BLUE GREEN & YELLOW 9 2 22 20 2 POWER CORD 22 2 0 5 2 0 2 7 Key Part No. Description QtyKey Part No. Description Qty 50079 Box... 2 905509 O-ring, 2. x 2.7 x.09... 5007050 Guard, switch... 500297 Meter (includes keys 2,7, & 9)... 5 50070 Cord, power... 50070 Wire unit, 2 AWG x ", brown... 7 505 Wire unit, 2 AWG x ", brown... 500707 Wire unit, 2 AWG x ", blue... 9 9059 Bumper, # 2 mch screw, rubber... 0 90529 Nut, hex, # 2... 52075 Screw, machine, # 2 x.500"... 2 90502 Nut, hex, # 2... 99790 Receptacle, amp female... 9052 Bushing, strain relief... 5 9977 Switch... 929 Nut, conduit, /2" lock... 7 905725 Screw, cap, # 2 x.750", skt btn hd... 9059 Nut, hex, # 2... 9 905225 Washer, # lock... 20 5205900 Plate, receptacle grounding... 2 520590 Plate, motor grounding... 22 5205905 Wire unit... 2 5205902 Wire unit... Decals 0 5007092 Decal, ON/OFF...2 500757 Decal, Identification... Greenlee / A Textron Company 5 55 Boeing Dr. Rockford, IL 09-29 USA 5-97-7070

Accessories Slip-in Couplers Key Part No. Description Qty 50000 Slip-in coupler for 2-/2" conduit (EMT, IMC or Rigid)... 50000 Slip-in coupler for " conduit (EMT, IMC or Rigid)... 50005 Slip-in coupler for -/2" conduit (EMT, IMC or Rigid)... 5000200 Slip-in coupler for " conduit (EMT, IMC or Rigid)... 5000277 Slip-in coupler for 5" conduit (EMT, IMC or Rigid)... 5 Screw-on Couplers 2 7 Key Part No. Description Qty 5000 Screw-on coupler set for 2-/2", ", -/2" and " conduit (includes items 2,, and ) 2 5000 Screw-on coupler for 2" IMC or Rigid only... 2 500075 Screw-on coupler for 2-/2" IMC or Rigid only... 2 500072 Screw-on coupler for " IMC or Rigid only... 2 50007 Screw-on coupler for -/2" IMC or Rigid only... 2 500070 Screw-on coupler for " IMC or Rigid only... 5000799 Adapter for screw-on IMC or Rigid only... 500077 Screw assembly (includes items 5, and 7)... 2 5 50007955 Screw... 500079 Handle... 7 905277 Roll Pin... Boom Tubes 9 Key Part No. Description Qty 50005 ' Boom tube... 9 5000792 ' Boom tube... Greenlee / A Textron Company 55 Boeing Dr. Rockford, IL 09-29 USA 5-97-7070

Accessories (cont d) T-Stand (50007) Wheeled Carriage (500070) 9 5 7 2 Key Part No. Description Qty 50007700 Frame... 2 9059 Wheel,.0/.50 x / shaft, " hub length... 50007 Axle... 2 502022 Spacer,.2 x.05 x.750"... 5* 500072 Puller pin... 2 * 90507002 Pin, roll,.7 x.50"... 2 7* 905002 Clip, hitch pin #... 2 905525 Retaining ring,.750", Truarc #50-75-S-PP... 9 5000 Decal, Warning... Repair Kit * 5007 Kit, puller pin (includes one each of the items marked with an asterisk)... 2 Greenlee / A Textron Company 7 55 Boeing Dr. Rockford, IL 09-29 USA 5-97-7070

Accessories (cont d) Boom Mount (50007) 5 9 2 7 Key Part No. Description Qty 500070 Frame... 2+ 5000755 Shaft... *+ 90507002 Pin, roll,.7 x.50"... *+ 905002 Clip, hitch pin #... 5 905050 Screw, cap, / x.000" hex head... * 500072 Puller pin... 2 7 5000920 Wheel unit, idler... 50797 Bushing... 2 9 50000 Decal, Warning... Repair Kits * 5007 Kit, puller pin (includes one each of the items marked with an asterisk)... 2 + 50097 Kit, shaft (includes one each of the items marked with a plus sign)... Greenlee / A Textron Company 55 Boeing Dr. Rockford, IL 09-29 USA 5-97-7070

Accessories (cont d) Nose Unit (5000) 2 5 7 5 9 Key Part No. Description Qty 50002 Elbow, adjustable... 2 50009 Sheave unit, 2"... 5000790 Shaft, elbow... 500072 Puller pin... 5* 90507002 Pin, roll,.7 x.50"... * 905002 Clip, hitch pin #... 7 905050 Screw, cap, / x.000" hex head... 905 Bushing... 2 9 500025 Decal, Warning... Repair Kit * 5007 Kit, puller pin (includes one each of the items marked with an asterisk)... 2 500925 Kit, elbow shaft (includes one of item and two of item 5)... 2 Greenlee / A Textron Company 9 55 Boeing Dr. Rockford, IL 09-29 USA 5-97-7070

Accessories (cont d) Elbow Unit (5000) 9 2 7 0 5 Key Part No. Description QtyKey Part No. Description Qty 50002 Elbow, adjustable... 2 500025 Elbow, pivot... 50009 Sheave unit, 2"... 5000 Shaft, pivot... 5* 50007 Pin, elbow... * 90507002 Pin, roll,.7 x.50"... 7* 905002 Clip, hitch pin #... 905050 Screw, cap, / x.000" hex head...2 9 905 Bushing...2 0 50097 Lanyard... 50002 Decal, Warning... Repair Kits * 5009 Kit, elbow pins (includes one each of the items marked with an asterisk)... 500950 Kit, pivot pins (includes one of item and two of item )... Greenlee / A Textron Company 20 55 Boeing Dr. Rockford, IL 09-29 USA 5-97-7070

Accessories (cont d) 5 Pipe Adapter Assembly (500025) 2 9 7 0 2 Key Part No. Description QtyKey Part No. Description Qty 5000 Frame... 2 50007 Sheave unit, "... * 500090 Shaft... * 90507002 Pin, roll,.7 x.50"... 5* 905002 Clip, hitch pin #... 50297 Foot... 7 9050579 Screw, cap, / 20 x.500", skt hd... 50272 Screw unit, 2" vise chain...2 9 502902 Handle unit, vise chain...2 0 5029 Positioner, chain...2 905 Bushing...2 2 5000 Decal, Warning... Repair Kit * 5009 Kit, shaft (includes one each of the items marked with an asterisk)... Greenlee / A Textron Company 2 55 Boeing Dr. Rockford, IL 09-29 USA 5-97-7070

Accessories (cont d) Floor Mount (500050) 2 Key Part No. Description Qty 5000790 Frame... 2 505070 Anchor, wedge,.25 x.00"... 50007 Decal, Warning... 55 Boeing Drive Rockford, IL 09-29 USA 5-97-7070 An ISO 900 Company Greenlee Textron Inc. is a subsidiary of Textron Inc. www.greenlee.com USA Tel: 00-5-07 Fax: 00-5-22 Canada Tel: 00-5-07 Fax: 00-52-25 International Tel: +-5-97-7070 Fax: +-5-97-927