SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 TUV SUD AMERICA - AUBURN HILLS 1755 Atlantic Blvd. Auburn Hills, MI 48326 William (Mac) Elliott Phone: 813 284 2736 MECHANICAL Valid To: August 31, 2018 Certificate Number: 2955.03 In recognition of the successful completion of the A2LA evaluation process, accreditation is granted to this laboratory at the location listed above to perform the following automotive, aerospace, medical products, and telecommunications tests: Thermal Testing: Custom Profiles (-73 to 190) C Temperature and Humidity: Temperature up to 90 C; Relative Humidity up to 97 %RH Thermal Shock: (-73 to 190) C Mechanical Shock: Up to 100 G s, Force rating 56,000 lbf., Drop Test from 10 meters. Vibration: Sine and Random, 3 Axis Vibration, Frequency Range (5 to 2,000) Hz, Force Pound Rating to 28,000 lbf., 4 inch displacement, Table Sizes up to 4 ft. x 12 ft. Environmental Vibration: Temperature (-73 to 177) C and Relative Humidity (12 to 97) %RH Environmental Life Cycle Durability/Fluid Dynamics/Corrosion/Erosion: Custom Liquid Temperature, Pressure and/or Flow Profiles ranging from (-40 to 140) C, (0 to 300) PSI and (0 to 125) gpm, respectively. Altitude Testing: Up to 50,000 ft, with custom profiles (-65 to 150) C Battery Testing: (0 to 900) VDC; (-1,000 to 1,000) ADC; (-250 to 250) kw Voltage: (0 to 900) VDC Amps: (0 to 6,000) A Resistance: (0 to 100G) Ohms Durability/Cycling Testing: Utilizing fixtures with Pneumatic Actuators up to 12 inches stroke and up to 2,000 lbs at Ambient, or using custom Thermal/Humidity Profiles from (-40 to 149) C and (12 to 97) %RH Water Tests: Up to 1,500 PSI, up to 22 GPM, and up to 90 C Test Technology/ Equipment Capabilities: Test Method(s) 1 : Durability / Cyclic Reliability* Electric Energy Storage System Testing* -Transport of Dangerous Goods Chrysler PF-10817 UN ST/SG/AC.10/11, Section 38.3.4: 38.3.4.1 Altitude Simulation; 38.3.4.2 Thermal Test; 38.3.4.3 Vibration; 38.3.4.4 Shock; 38.3.4.5 External Short Circuit; 38.3.4.6 Impact; 38.3.4.7 Overcharge; 38.3.4.8 Forced Discharge (A2LA Cert. No. 2955.03) Revised 006/15/2018 Page 1 of 5
Test Technology/ Equipment Capabilities: Test Method(s) 1 : Electric Energy Storage System Testing* Electric and Hybrid Electric Vehicle Rechargeable Energy Storage System Safety and Abuse Testing Freedom CAR Battery Test Manual* Rechargeable Energy Storage System Safety and Abuse Testing Fuel Tank Testing* Fuel Tank Specification-Plastic SAE J2464, Section 4: 4.3.1 Shock Test; 4.3.2 Drop Test; 4.3.3 Penetration Test; 4.3.4 Roll Over Test; 4.3.5 Immersion Test; 4.3.6 Crush Test; 4.4.2 Thermal Stability Test; 4.4.4 Thermal Shock Cycling; 4.4.5 Passive Propagation Resistance Test; 4.5.1.1.1 Cell Hard Short; 4.5.1.1.2 Cell Soft Short; 4.5.2 Overcharge Test; 4.5.3 Overdischarge Test DOE/ID-11069: 3.2 Static Capacity Test; 3.3 Hybrid Pulse Power Characterization; 3.4 Self Discharge; 3.5 Cold Cranking; 3.6 Thermal Performance Test; 3.7 Energy Efficiency Test; 3.9 Cycle Life Test; 3.10 Calendar Life Test Chrysler PF-8950 (2009): 7.2 Climatic Cycle Test; 7.3 Pressure/Vacuum Cycling and Deflection; 7.5 Slosh; 7.6 Assembly Shake/Vibration Durability; 7.7 Vibration Resonance and Frequency Response Environmental Life Cycle / Durability* PF 10827 (2011); GM 9505P (2005), 9080P (Section 5.6); SAE J2044, Section 7.5 (2002); GMW 14785, GMW 14124 Humidity* GMW 3431 (Section 4.4.5); GMW 3172 (Sections 9.4.5 and 9.4.6); MIL-STD-810, Method 507; IEC 68-2-38 Temperature/ Thermal Shock* PF-10388 (Section 3.2) (2004); GM 9505P (2005); GMW 3172 (Sections 8.4.2 to 8.5.1 and 9.4.1 to 9.4.3); GMW 14124; MIL-STD-810, Methods 501, 502, and 503 Vibration* (Including Environmental Vibration) Chrysler PF- 10827 (2011); GM 9110P (Section 7.7); GMW 3172 (Section 9.3.1); GMW 3431 (Section 4.3.12); MIL-STD-810, Method 514; SAE J2380 (1998) (A2LA Cert. No. 2955.03) Revised 006/15/2018 Page 2 of 5
Test Technology/ Equipment Capabilities: Test Method(s) 1 : Mechanical Shock Testing* GMW 3172 (Sections 9.3.3, 9.3.4, and 9.3.5); GMW 3431 (Section 4.3.11); MIL-STD-810, Method 516 Altitude* MIL-STD-810D, Method 500.2; GMW 3172 (Rev F, Section 4.2.8); SAE J1455 Dust Testing* GMW 3172 (Section 9.5.1); GMW 3431 (Section 4.4.9) Corrosion/Erosion* ASTM D2570; GMW14193 (2008) Section 4.12 Material Evaluations* Cleanability / Solvent Rub LP-463PB-31-01 (2007) Impact Resistance Cycle Crack LP-463PB-19-01 LP-463PB-22-01 Fluid Resistance LP-463PB-31-01 (2007); GMW 3431 (Section 4.5.1) Resistance to Heat Age MS-JP7-5; 463LB-13-01; PF-11084 Cold Crack Impact Resistance Nissan M0134 (2002) Water Tests* DIN 40 050-9; ISO 16750-4 Section 5.4 SAFETY TESTING Test Technology: Test Method 1,2 : Eye Protectors for Selected Sports Eye Protective Devices for Paintball Sports Standard Specification for Eye Protectors for Field Hockey Standard Specification for Eye Protectors for Women s Lacrosse Safety Specification for Bunk Beds Safety Standard for Entrapment Hazards Bunk Beds ASTM F803 ASTM F1776 ASTM F2713 ASTM F3077 ASTM F1427 16 CFR 1213 Requirements for Bunk Beds 16 CFR 1513 (A2LA Cert. No. 2955.03) Revised 006/15/2018 Page 3 of 5
Test Technology: Test Method 1,2 : Furniture Tests: Safety and Performance Test Requirements for Bunkable and Loftable Beds, Beds with Drawers and Drawer Units for use Under Beds Home Playground Equipment (Except Swing Impact) Standard Specification for Impact Attenuation of Surface Systems Under & Around Playground Equipment Standard Specification for Impact Attenuation of Turf Playing Systems as Measured in the Field Standard Specification for Pole Vault Box Collars Standard Specification for Pole Vault Landing Systems Standard Safety Performance Specification for Soft Contained Play Equipment Playground Equipment and Surfacing Coefficient of Restitution (COR) of Baseballs and Softballs Determination of Accessibility of Surface Systems Standard Specification for Indoor Wall/Feature Padding Shock Absorbing Properties of Play Systems Technical Requirement for Determining a Sharp Point in Toys and Other Articles Intended for use by Children Under 8 Years of Age Technical Requirement for Determining a Sharp Metal or Glass Edge in Toys and Other Articles Intended for use by Children Under 8 Years of Age GSA 3FNE 99-582D ASTM F1148 ASTM F1292 3 ASTM F1936 4 ASTM F2949 ASTM F1162 / F1162M ASTM F1918 EN 1176: Parts 1, 2, 3, 4, 5, 6, 7, 10, and 11 ASTM F1887 ASTM F1951 ASTM F2440 ASTM F355 16 CFR 1500 (Section 48) 16 CFR 1500 (Section 49) Small Parts 16 CFR 1501 Engineered Wood Fiber for use as a Playground Safety Surface Under and Around Playground Equipment Standard Specification for Loose-Fill Rubber for use as a Playground Safety Surface Under and Around Playground Equipment ASTM F2075 3 (except section 8) ASTM F3012 (except sections 8 and 10) (A2LA Cert. No. 2955.03) Revised 006/15/2018 Page 4 of 5
Test Technology: Test Method 1,2 : Consumer Safety Performance Specification for Playground Equipment for Public Use ASTM F1487 Standard Specification for Unsupervised Public Use Outdoor Fitness Equipment Permanently Installed Outdoor Fitness Equipment Safety Requirements and Test Methods ASTM F3101 15 EN 16630:2015 *Including customer supplied and industry specifications directly related to the test technologies and parameters listed above. 1 When the date, revision, or edition of a test method standard is not identified on the scope of accreditation, the laboratory is expected to be using the current version within one year of the date of publication, per part C., Section 1 of A2LA R101 - General Requirements - Accreditation of ISO-IEC 17025 Laboratories. 2 The Consumer Product Safety Improvement Act (CPSIA) requires that every children's product subject to a federal consumer product safety requirement be tested by a Consumer Product Safety Commission (CPSC) accepted laboratory for compliance with the applicable federal children's product safety requirements. Accreditation by A2LA does not infer acceptance by the CPSC. Please verify this organization s acceptance status by using the CPSC s searchable database, located at http://www.cpsc.gov/cgi-bin/labsearch/. 3 The lab performs internal and field testing for these test methods. This laboratory meets A2LA R104 General Requirements: Accreditation of Field Testing and Field Calibration Laboratories for these tests. 4 This test method is only performed in the field /onsite. (A2LA Cert. No. 2955.03) Revised 006/15/2018 Page 5 of 5
Accredited Laboratory A2LA has accredited TUV SUD AMERICA - AUBURN HILLS Auburn Hills, MI for technical competence in the field of Mechanical Testing This laboratory is accredited in accordance with the recognized International Standard ISO/IEC 17025:2005 General requirements for the competence of testing and calibration laboratories. This accreditation demonstrates technical competence for a defined scope and the operation of a laboratory quality management system (refer to joint ISO-ILAC-IAF Communiqué dated 8 January 2009). Presented this 5 th day of May 2016. President and CEO For the Accreditation Council Certificate Number 2955.03 Valid to August 31, 2018 Revised June 15, 2018 For the types of tests to which this accreditation applies, please refer to the laboratory s Mechanical Scope of Accreditation.